i-700 Product Information Guide V3
Technical Specifications Frequency Range 1.88~1.90GHz Channels 120 Duplex channels RF Carrier Power <250mW Modulation GFSK Frequency Stability <± Charging time 15 hours Ambient temperature Normal: 15℃ ~ 35℃, Extreme: 0℃ ~ 40℃ Humidity 0%~90% Size (mm) Base: 179 x 106 x 43; Handset: 162 x 50 x 24 Power supply Base input: 6V, 1000/300 mA； Handset input: Ni-MH 1.2V x 2, 800mAh 50 KHz ? Design and specifications are subject to change without notice.
Introduction Thank you for purchasing the color DECT BT phone. Your new DECT (Digital Enhanced Cordless Telecommunications) can connect to an iPhone with Bluetooth function, which enables you to make calls through cell phone lines and landline. Enjoy these additional features, as well: Large displays and accessible menus. Color display - Customizable with wallpapers and backgrounds. iPhone charger - Charge an iPhone using a port on your new phone.
Chapter 10: Additional Information Troubleshooting Symptom The handset doesn't turn on. Solution Try charging the handset for a few minutes, then remove it from the base. If it still doesn't turn on, check the battery installation. If these efforts are unsuccessful, try replacing the batteries. Contact an authorized service center. The handset works, but it doesn't access the base unit. Check the connection of the switching power supply. Try registering the handset to the base.
Contents Contacts Home Chapter 1: Getting Started 7 Features List Cell 1 9 Phone Layout Cell 2 10 Key Functions Handset 12 Handset Screen PIN code 13 Package Contents Register 14 Connecting 14 Installing the Batteries Select base 15 Charging Reset handset 15 Turning On or Off the Phone 16 Registering a New Handset Auto answer 17 Deactivating a Handset Language 18 Choosing the Dialing Mode 18 Setting Date & Time Base PIN: (1590) Chapter 2: Bluetooth Flash time Dial mode 20 Pairing w
Chapter 9: Menu Structure 28 Flash Signal 28 Using a Pause 29 Out of Range Indicator Bluetooth Add device Device list 29 Locking the Keypad 30 Paging 30 Temporary Tone-Dial Switchover 31 Intercom Display Contrast 31 Transferring Calls between Handsets 32 Three-way Conference Calling Wallpaper Background Handset name Chapter 4: Display and Sound 33 Display Contrast 33 Wallpaper 34 Background color Sound Cell ringtone PSTN ringtone 34 Handset Name 35 Ring Setting 36 Key Tone INT ringtone 36 Powe
44 Editing or Deleting Contacts 45 Download Phonebook from the iPhone Chapter 7: Settings 46 Changing the Handset & Base PIN 48 Selecting a Base 49 Resetting the Handset or the Base 51 Auto Answer 51 Language 52 Flash Time Chapter 8: Date and Time 53 Date Format 53 Time Format 54 Alarm 55 Sleep Mode 56 Chapter 9: Menu Structure Chapter 10: Additional Information Sleep Mode This feature enables you to not be disturbed by the ring tone at night.
Alarm Chapter 1: Getting Started You can set an alarm to ring once or ring in regular intervals about every 10 minutes. Features List Activating the Alarm Feature Color DECT BT Phone 1 Press 2 Press 3 Press beneath Menu to display the main menu items. Date and time to choose , then press beneath Select. beneath Select to choose Alarm. or Down 4 Press Up beneath Select. to choose "ON", and then press 5 Use the numeric keys to enter the time using the HH:MM format.
selectable background colors Call duration display Internal calling Password protection Mute function Real clock (12-hour or 24-hour) Keypad lock Redial, Flash, Pause Preparation dialing Sleep mode selection Alarm Landline FSK/DTMF Caller ID Incoming call indicator Private/Out of area notification Message waiting notification Selectable dialing mode Selectable Flash time Chapter 8: Date and Time Date Format If you have set the date, you can choose the date format.
Flash Time Phone Layout During a conversation, allows you to access special services offered by your telephone network or to transfer a call to another extension if you are connected to a PABX (Private Automatic Branch of eXchange). Handset Earpiece If your key does not work properly, you need to adjust the Flash time, as follows: 1 Press 2 Press beneath Menu to display the main menu items. Base to choose , then press beneath Select.
Key Functions Press to enter # or to switch between upper case and lower case letters in the English mode. Press and hold to turn on or off the keypad lock function. Select keys: Press to perform the function listed above the key. Press to turn on the phone. If you press and hold, the phone turns off. While navigating through menus, briefly press it to cancel your input and return to the main screen. During a call, briefly press it to end the call.
Select Keys Resetting the Base 1 Press beneath Menu to display the main menu items. Base 2 Press to choose , then press beneath Select. 3 The handset prompts you to enter the current base PIN code (the default PIN is 1590). Use the numeric keys to enter the beneath OK. PIN, and then press 4 Press Up or Down beneath Select. Contacts Left: Select Back Right: OK Save . Be careful! When you reset the handset, you will lose any data stored in it (e.g. Numbers in the incoming and outgoing lists).
Handset Screen Resetting the Handset or the Base The screen shows various icons. If you reset the handset or the base, all of the user-selectable features restore to the factory settings: When resetting the handset, the incoming and outgoing lists will be erased, but the Contacts and Flash time do not reset. Signal strength. The greater the number of bars, the stronger the signal. The handset and base can be reset independently. It is useful for the following purposes: The landline is engaged.
Selecting a Base Package Contents Your handset can be used with up to 4 base units, provided that it has been registered with them. This menu option enables you to select which base you want to use: Once you have unpacked your phone, make sure that you have all of these parts. If any component is missing or broken, please call your dealer. 1 Press beneath Menu to display the main menu items. Handset 2 Press to choose 3 Press Up or Down beneath Select. press or Down 4 Press Up beneath Select.
Connecting Base PIN 1 Connect the plug of the power supply to the power jack of the base, and then plug the power supply into a standard AC wall outlet. 1 Press 2 Connect one end of the phone line cord to the phone line jack on the base, and then connect the other end to a standard phone wall outlet. 2 Press beneath Menu to display the main menu items. Base to choose , then press 3 The handset prompts you to enter the current base PIN code (the default PIN is 1590).
Chapter 7: Settings Notes: Changing the Handset & Base PIN Base and handset PINs are required to protect your phone against unauthorized use. They are set to 1590 at the factory. You can change the PINs as follows: Charging Handset PIN 1 Press 2 Press 3 Press Replace batteries if they don't recover their full storage capacity after recharging. When replacing the batteries, always use high quality Ni-MH re-chargeable batteries. Never use other types of batteries.
Registering a New Handset 3 Press To share your phone line with other people, you can register up to 5 handsets to your base. To do this, assign a new number to each handset that you register. The supplied handset is already registered with the number 1, appearing as 1. For security reasons, the registration procedure can only be performed by people who are close to your base and know the REGISTER PIN. Please note that this PIN cannot be modified.
Speed Dial Note: You can store up to 9 speed dial numbers on the numeric keypad (0~9), so you can easily dial the numbers by pressing and holding the associated numeric key. To extend radio coverage, a handset can be registered to up to 4 different base units. A base can be used with up to 5 handsets, and one base can connect to only one handset at a time. Storing Speed Dial Numbers 1 Press beneath Menu to display the main menu items.
Choosing the Dialing Mode Reviewing or Dialing a Number in Contacts Your phone can be set to pulse dialing (rotary), or tone dialing (DTMF). To change the dialing mode: You can search stored contacts by entering the first characters of their names (alphabetic search). You can also scroll through the entire list without accessing the Contacts menu. 1 Press 2 Press beneath Menu to display the main menu items. Base to choose , then press beneath Select.
Method 2: In Standby Mode 1 Enter a phone number, then press Notes: beneath Save. 2 Complete storage by starting from Step 4 in the last paragraph of Method 1. When setting the month, you can enter 1 digit or 2 digits at a time, but it is displayed in 2-digit format. (For example: For August, you can enter 8 or 08 in the month field, but the display shows "08".
Chapter 2: Bluetooth Chapter 6: Contacts Pairing with an iPhone To use an iPhone with your DECT phone, you must first pair and connect the iPhone with the DECT phone. You can store frequently used numbers so that you can easily make a call without having to remember or enter the phone number. You can store up 200 entries in your contact list. Storing Contact Entries 1 Turn on the Bluetooth feature of your iPhone.
Dialed Calls List Method 2: Using the DECT Phone Menu The last 20 dialed calls are stored in the Dialed Calls list. You can review, redial, delete and save these numbers. 1 Press 1 Press 2 Press beneath Menu to display the main menu items. Call logs to choose , then press beneath Select. or Down to choose Dialed calls, then press 3 Press Up beneath Select. The last dialed number appears on the screen. 4 Press Up or Down to find the desired number, press beneath Select.
Disconnecting an iPhone 1 Press 2 Press Notes: beneath Menu to display the main menu items. Bluetooth to choose 3 Press Down Select. , then press beneath Select. to choose Device list, press beneath 4 The display shows all devices that have been paired before. Press Up or Down to choose the desired device, press beneath Select. 5 Press beneath Select to choose Disconnect. Then a prompt tone occurs and Not Connected appears to the right of i-700 on the iPhone screen.
Chapter 5: Call Logs Removing a Paired iPhone Answered or Missed Calls If you already have the maximum of seven paired iPhones in the Device list and you want to add another iPhone, you must first delete a paired iPhone. When you receive a call and you subscribe to your network provider’s caller ID service, if the caller's information is transmitted from the network on which the call was made (and the caller doesn't hide it), the caller's phone number is displayed.
Chapter 3: Basic Functions Charging Tone Making a Call Every time you place the handset on the base, a tone occurs. This tone confirms that the handset is charging. You can switch the tone ON or OFF. When you dial, up to 25 digits appear on the screen. If the number is longer than 16 digits, the digits become smaller to accommodate the whole number. 1 Press beneath Menu to display the main menu items.
Key Tone Call Switching between the DECT Phone and an iPhone Every time that you press a key, your handset acknowledges it with a key tone. You can disable the key tones. During a call, you can switch between your DECT phone and your iPhone. 1 Press 2 Press beneath Menu to display the main menu items. Sound to choose 3 Press Up or Down beneath Select. , then press beneath Select.
Receiving a Call Ring Setting When a call is received, the phone rings and "Incoming Call" appears on the screen. indicates a landline call or indicates a cellphone line call. If the incoming call can be identified (i.e. The caller's information is transmitted) you also see the caller's number. You can select unique cell, landline and internal call ring tones and volumes. There are 15 ringtones, and four volume levels. You can also turn off the ringer.
Using the Speakerphone Background Color 1 Press beneath Menu to display the main menu items. Display 2 Press to choose , then press beneath Select. During a call, you can turn on the speakerphone that is built into the handset. You can simply put your handset on a surface (e.g. a desk) and enjoy the comfort of a handsfree conversation. 3 Press Up or Down to choose Background, then beneath Select. The current setting appears on press the screen. To turn on the speakerphone, press appears.
Last Number Redial Chapter 4: Display and Sound Your phone allows you to quickly redial the last dialed number. Display Contrast Pick up the handset and press to engage the line. Then press beneath Redial to dial the last-dialed number. This adjustment enables you to optimize the visibility of the display by changing its contrast according to environmental conditions. 1 Press 2 Press If your phone service includes call waiting or conference call services, you can use to initiate these functions.
Three-way Conference Calling Out of Range Indicator When you have an external call and an intercom call in progress, you can set up a three-way conference call, like this: The bars to the right of show the signal strength received from the base. If you are too far from the base, the radio signal might become too weak for the phone to access the telephone line. In these conditions you can't make or receive phone calls, and turns red and "Searching..." appears.
Paging Intercom You can page the handset from the base by making the handset ring with a special ring. It's useful to locate a lost handset or call the user who currently has the handset. If you connected more than one handset to a base (you can connect up to 5 handsets to the same base), you can have a conversation between two people using two different handsets. To send the paging signal, briefly press , located on the base. All handsets registered with the base ring for 15 seconds. .
Paging Intercom You can page the handset from the base by making the handset ring with a special ring. It's useful to locate a lost handset or call the user who currently has the handset. If you connected more than one handset to a base (you can connect up to 5 handsets to the same base), you can have a conversation between two people using two different handsets. To send the paging signal, briefly press , located on the base. All handsets registered with the base ring for 15 seconds. .
Three-way Conference Calling Out of Range Indicator When you have an external call and an intercom call in progress, you can set up a three-way conference call, like this: The bars to the right of show the signal strength received from the base. If you are too far from the base, the radio signal might become too weak for the phone to access the telephone line. In these conditions you can't make or receive phone calls, and turns red and "Searching..." appears.
Last Number Redial Chapter 4: Display and Sound Your phone allows you to quickly redial the last dialed number. Display Contrast Pick up the handset and press to engage the line. Then press beneath Redial to dial the last-dialed number. This adjustment enables you to optimize the visibility of the display by changing its contrast according to environmental conditions. 1 Press 2 Press If your phone service includes call waiting or conference call services, you can use to initiate these functions.
Using the Speakerphone Background Color 1 Press beneath Menu to display the main menu items. Display 2 Press to choose , then press beneath Select. During a call, you can turn on the speakerphone that is built into the handset. You can simply put your handset on a surface (e.g. a desk) and enjoy the comfort of a handsfree conversation. 3 Press Up or Down to choose Background, then beneath Select. The current setting appears on press the screen. To turn on the speakerphone, press appears.
Receiving a Call Ring Setting When a call is received, the phone rings and "Incoming Call" appears on the screen. indicates a landline call or indicates a cellphone line call. If the incoming call can be identified (i.e. The caller's information is transmitted) you also see the caller's number. You can select unique cell, landline and internal call ring tones and volumes. There are 15 ringtones, and four volume levels. You can also turn off the ringer.
Key Tone Call Switching between the DECT Phone and an iPhone Every time that you press a key, your handset acknowledges it with a key tone. You can disable the key tones. During a call, you can switch between your DECT phone and your iPhone. 1 Press 2 Press beneath Menu to display the main menu items. Sound to choose 3 Press Up or Down beneath Select. , then press beneath Select.
Chapter 3: Basic Functions Charging Tone Making a Call Every time you place the handset on the base, a tone occurs. This tone confirms that the handset is charging. You can switch the tone ON or OFF. When you dial, up to 25 digits appear on the screen. If the number is longer than 16 digits, the digits become smaller to accommodate the whole number. 1 Press beneath Menu to display the main menu items.
Chapter 5: Call Logs Removing a Paired iPhone Answered or Missed Calls If you already have the maximum of seven paired iPhones in the Device list and you want to add another iPhone, you must first delete a paired iPhone. When you receive a call and you subscribe to your network provider’s caller ID service, if the caller's information is transmitted from the network on which the call was made (and the caller doesn't hide it), the caller's phone number is displayed.
Disconnecting an iPhone 1 Press 2 Press Notes: beneath Menu to display the main menu items. Bluetooth to choose 3 Press Down Select. , then press beneath Select. to choose Device list, press beneath 4 The display shows all devices that have been paired before. Press Up or Down to choose the desired device, press beneath Select. 5 Press beneath Select to choose Disconnect. Then a prompt tone occurs and Not Connected appears to the right of i-700 on the iPhone screen.
Dialed Calls List Method 2: Using the DECT Phone Menu The last 20 dialed calls are stored in the Dialed Calls list. You can review, redial, delete and save these numbers. 1 Press 1 Press 2 Press beneath Menu to display the main menu items. Call logs to choose , then press beneath Select. or Down to choose Dialed calls, then press 3 Press Up beneath Select. The last dialed number appears on the screen. 4 Press Up or Down to find the desired number, press beneath Select.
Chapter 2: Bluetooth Chapter 6: Contacts Pairing with an iPhone To use an iPhone with your DECT phone, you must first pair and connect the iPhone with the DECT phone. You can store frequently used numbers so that you can easily make a call without having to remember or enter the phone number. You can store up 200 entries in your contact list. Storing Contact Entries 1 Turn on the Bluetooth feature of your iPhone.
Method 2: In Standby Mode 1 Enter a phone number, then press Notes: beneath Save. 2 Complete storage by starting from Step 4 in the last paragraph of Method 1. When setting the month, you can enter 1 digit or 2 digits at a time, but it is displayed in 2-digit format. (For example: For August, you can enter 8 or 08 in the month field, but the display shows "08".
Choosing the Dialing Mode Reviewing or Dialing a Number in Contacts Your phone can be set to pulse dialing (rotary), or tone dialing (DTMF). To change the dialing mode: You can search stored contacts by entering the first characters of their names (alphabetic search). You can also scroll through the entire list without accessing the Contacts menu. 1 Press 2 Press beneath Menu to display the main menu items. Base to choose , then press beneath Select.
Speed Dial Note: You can store up to 9 speed dial numbers on the numeric keypad (0~9), so you can easily dial the numbers by pressing and holding the associated numeric key. To extend radio coverage, a handset can be registered to up to 4 different base units. A base can be used with up to 5 handsets, and one base can connect to only one handset at a time. Storing Speed Dial Numbers 1 Press beneath Menu to display the main menu items.
Registering a New Handset 3 Press To share your phone line with other people, you can register up to 5 handsets to your base. To do this, assign a new number to each handset that you register. The supplied handset is already registered with the number 1, appearing as 1. For security reasons, the registration procedure can only be performed by people who are close to your base and know the REGISTER PIN. Please note that this PIN cannot be modified.
Chapter 7: Settings Notes: Changing the Handset & Base PIN Base and handset PINs are required to protect your phone against unauthorized use. They are set to 1590 at the factory. You can change the PINs as follows: Charging Handset PIN 1 Press 2 Press 3 Press Replace batteries if they don't recover their full storage capacity after recharging. When replacing the batteries, always use high quality Ni-MH re-chargeable batteries. Never use other types of batteries.
Connecting Base PIN 1 Connect the plug of the power supply to the power jack of the base, and then plug the power supply into a standard AC wall outlet. 1 Press 2 Connect one end of the phone line cord to the phone line jack on the base, and then connect the other end to a standard phone wall outlet. 2 Press beneath Menu to display the main menu items. Base to choose , then press 3 The handset prompts you to enter the current base PIN code (the default PIN is 1590).
Selecting a Base Package Contents Your handset can be used with up to 4 base units, provided that it has been registered with them. This menu option enables you to select which base you want to use: Once you have unpacked your phone, make sure that you have all of these parts. If any component is missing or broken, please call your dealer. 1 Press beneath Menu to display the main menu items. Handset 2 Press to choose 3 Press Up or Down beneath Select. press or Down 4 Press Up beneath Select.
Handset Screen Resetting the Handset or the Base The screen shows various icons. If you reset the handset or the base, all of the user-selectable features restore to the factory settings: When resetting the handset, the incoming and outgoing lists will be erased, but the Contacts and Flash time do not reset. Signal strength. The greater the number of bars, the stronger the signal. The handset and base can be reset independently. It is useful for the following purposes: The landline is engaged.
Select Keys Resetting the Base 1 Press beneath Menu to display the main menu items. Base 2 Press to choose , then press beneath Select. 3 The handset prompts you to enter the current base PIN code (the default PIN is 1590). Use the numeric keys to enter the beneath OK. PIN, and then press 4 Press Up or Down beneath Select. Contacts Left: Select Back Right: OK Save . Be careful! When you reset the handset, you will lose any data stored in it (e.g. Numbers in the incoming and outgoing lists).
Key Functions Press to enter # or to switch between upper case and lower case letters in the English mode. Press and hold to turn on or off the keypad lock function. Select keys: Press to perform the function listed above the key. Press to turn on the phone. If you press and hold, the phone turns off. While navigating through menus, briefly press it to cancel your input and return to the main screen. During a call, briefly press it to end the call.
Flash Time Phone Layout During a conversation, allows you to access special services offered by your telephone network or to transfer a call to another extension if you are connected to a PABX (Private Automatic Branch of eXchange). Handset Earpiece If your key does not work properly, you need to adjust the Flash time, as follows: 1 Press 2 Press beneath Menu to display the main menu items. Base to choose , then press beneath Select.
9 selectable background colors Call duration display Internal calling Password protection Mute function Real clock (12-hour or 24-hour) Keypad lock Redial, Flash, Pause Preparation dialing Sleep mode selection Alarm Landline FSK/DTMF Caller ID Incoming call indicator Private/Out of area notification Message waiting notification Selectable dialing mode Selectable Flash time Chapter 8: Date and Time Date Format If you have set the date, you can choose the date format.
Alarm Chapter 1: Getting Started You can set an alarm to ring once or ring in regular intervals about every 10 minutes. Features List Activating the Alarm Feature Color DECT BT Phone 1 Press 2 Press 3 Press beneath Menu to display the main menu items. Date and time to choose , then press beneath Select. beneath Select to choose Alarm. or Down 4 Press Up beneath Select. to choose "ON", and then press 5 Use the numeric keys to enter the time using the HH:MM format.
44 Editing or Deleting Contacts 45 Download Phonebook from the iPhone Chapter 7: Settings 46 Changing the Handset & Base PIN 48 Selecting a Base 49 Resetting the Handset or the Base 51 Auto Answer 51 Language 52 Flash Time Chapter 8: Date and Time 53 Date Format 53 Time Format 54 Alarm 55 Sleep Mode 56 Chapter 9: Menu Structure Chapter 10: Additional Information Sleep Mode This feature enables you to not be disturbed by the ring tone at night.
Chapter 9: Menu Structure 28 Flash Signal 28 Using a Pause 29 Out of Range Indicator Bluetooth Add device Device list 29 Locking the Keypad 30 Paging 30 Temporary Tone-Dial Switchover 31 Intercom Display Contrast 31 Transferring Calls between Handsets 32 Three-way Conference Calling Wallpaper Background Handset name Chapter 4: Display and Sound 33 Display Contrast 33 Wallpaper 34 Background color Sound Cell ringtone PSTN ringtone 34 Handset Name 35 Ring Setting 36 Key Tone INT ringtone 36 Powe
Contents Contacts Home Chapter 1: Getting Started 7 Features List Cell 1 9 Phone Layout Cell 2 10 Key Functions Handset 12 Handset Screen PIN code 13 Package Contents Register 14 Connecting 14 Installing the Batteries Select base 15 Charging Reset handset 15 Turning On or Off the Phone 16 Registering a New Handset Auto answer 17 Deactivating a Handset Language 18 Choosing the Dialing Mode 18 Setting Date & Time Base PIN: (1590) Chapter 2: Bluetooth Flash time Dial mode 20 Pairing w
Chapter 10: Additional Information Troubleshooting Symptom The handset doesn't turn on. Solution Try charging the handset for a few minutes, then remove it from the base. If it still doesn't turn on, check the battery installation. If these efforts are unsuccessful, try replacing the batteries. Contact an authorized service center. The handset works, but it doesn't access the base unit. Check the connection of the switching power supply. Try registering the handset to the base.
Introduction Thank you for purchasing the color DECT BT phone. Your new DECT (Digital Enhanced Cordless Telecommunications) can connect to an iPhone with Bluetooth function, which enables you to make calls through cell phone lines and landline. Enjoy these additional features, as well: Large displays and accessible menus. Color display - Customizable with wallpapers and backgrounds. iPhone charger - Charge an iPhone using a port on your new phone.
Technical Specifications Frequency Range 1.88~1.90GHz Channels 120 Duplex channels RF Carrier Power <250mW Modulation GFSK Frequency Stability <± Charging time 15 hours Ambient temperature Normal: 15℃ ~ 35℃, Extreme: 0℃ ~ 40℃ Humidity 0%~90% Size (mm) Base: 179 x 106 x 43; Handset: 162 x 50 x 24 Power supply Base input: 6V, 1000/300 mA； Handset input: Ni-MH 1.2V x 2, 800mAh 50 KHz ? Design and specifications are subject to change without notice.
i-700 Product Information Guide V3
