speeCup Product Information Guide 2014-04
IMPORTANT To get the full capability of your new speeCup, please read this manual. It's more than just a Bluetooth Speaker! SPEECUP'S INTUITIVE SMARTCONTROL INTERFACE Press anywhere on the perimeter of speeCup smartControl Start/Pause music Interrupt music to answer an incoming call Hang up a call and resume music Increase or decrease volume Pause a movie or video Other Controls: Track up/down Access voice command Use hand gesture controls CARE AND MAINTENANCE 1.
CHARGING speeCup has a built-in Li-ion battery (3.7V, 1.6A), so it can be used without connecting to a power supply. To charge the battery, follow these steps: 1. Connect the micro USB connector to the speeCup DC 5V input. 2. Plug the USB full-size connector into the 12V accessory car plug supplied. 3. A common USB type AC charger (DC 5V, 500mA) can be used as well. 4. speeCup can be charged by plugging the USB connector into a computer. When speeCup is charging the LED status indicator will be RED.
SMARTCONTROL INTERFACE Top view Smartphone Voice Command access Music track UP/Down buttons LED status indicator Front view Bottom view smartControl perimeter interface Microphone Power ON/OFF switch Rear view Micro USB jack Audio Out 3
OPERATION Turning speeCup On or Off The ON/OFF switch is located and clearly marked on the bottom of the speeCup. The standby time of speeCup is 336 Hours. It is not necessary to switch speeCup to the OFF position unless it will not be used for extended periods. Pairing speeCup with Smartphone or Any Bluetooth Enabled Music Device To use speeCup with any Bluetooth enabled smartphone or tablet, you must first pair the device to the speeCup.
Connecting with iPhone 1. Turn the Bluetooth feature of the iPhone to ON. It will then begin searching for any Bluetooth device within range. 2. Make sure the speeCup is turned to the ON position, then press and hold the smartControl for about 3 seconds until the orange and blue LED flash alternately. 3. You will see speeCup on the Devices list. Touch the speeCup to pair, and you will see that it's Connected.
Clear speeCup from iPhone Touch the as shown below, then you will see Forget this Device, touch this option and confirm by the red prompt.
Connecting with Android phone 1. Turn the Bluetooth feature of the Android phone to ON. It will then begin searching for any Bluetooth device within range. 2. Make sure the speeCup is turned to the ON position, then press and hold the smartControl for about 3 seconds until the orange and blue LED flash alternately. 3. You will see speeCup on the Available devices list. Touch the speeCup to pair, and you will see that it's Connected on the Paired devices list.
8
Clear speeCup from Android phone Touch the as shown below, then you will see Unpair, touch this option and confirm. Clear all the devices from speeCup Turn the speeCup to the ON position, then press and hold the smartControl for several seconds until you hear a confirmation beep.
USING VOICE COMMAND FUNCTIONS Voice commands with Siri or S Voice OFF Simple voice commands of numbers or contact names can be given to speeCup by pressing the once briefly in the center of speeCup and wait to hear the sound indicating voice command is ready to access. Voice commands with Siri or S Voice Enabled To access voice commands press the once briefly and wait to hear the sound indicating voice command is ready to access. Do NOT press and HOLD the button, but press briefly once.
GESTURE 1. When a call is received, wave left or right in the direction of the gray arrows to answer it. For details, see the picture below. 2. To end a call, wave left or right again. 3. While playing music, wave left or right to select the desired track. The distance between your hand and the speeCup should be less than 2.4 inches (6cm). By default the feature is switched off. To switch it on, press and hold for several seconds until you hear a confirmation beep .
AUDIO OUT speeCup can also be connected to other audio devices like your car audio system, home audio system or sound bar using the 3.5mm audio out cord provided. Music from the Bluetooth connected device will play on the audio system connected to speeCup. Any use of a mobile device for phone calls or voice commands will pause the music and speeCup will function normally as a hands free interface to the Bluetooth connected mobile device.
STEREO AUDIO OUTPUT TO HOME SYSTEM Connecting speeCup to a home audio system will provide a useful way to hold your Bluetooth connected smartphone or tablet in your hand and let speeCup act as an interface to your sound system. Though each audio system is a little different, speeCup’s 3.5mm stereo output can be connected using a variety of cables and connectors available on-line or at retail stores.
ADJUSTING VOLUME To adjust speeCup’s volume, rotate the smartControl clockwise to increase the volume or counter-clockwise to decrease it. Volume can be adjusted by either the smartControl or the Bluetooth device speeCup is connected to. LOW BATTERY INDICATION Apple iOS battery indication: FULL LOW Other Bluetooth device: may be no indication By default the sound indication on speeCup is switched off. To switch it on, press and hold until a confirmation tone occurs.
SPECIFICATIONS Frequency Range: 2.402GHz - 2.480GHz Channels: 79 Carrier Power: <2.
