Manual IB-M2HSF-705 Swivelling M.2 heat pipe heat sink with fan Handbuch IB-M2HSF-705 Schwenkbarer M.
Safety information IB-M2HSF-705 Please read carefully the following information to prevent injuries, damage to material and device as well as data loss: Warning levels Signal words and safety codes indicate the warning level and provide immediate information in terms of the probability of occurrence as well as the type and severity of the consequences if the measures to prevent hazards are not complied with.
Safety information IB-M2HSF-705 • • Guarantee sufficient ambient air for the device/power unit Do not place objects on the device/power unit 4. Hazards caused by very small parts and packaging Risk of suffocation Risk of death by suffocation or swallowing • Keep small parts and accessories away from children • Store/dispose of plastic bags and packaging in an area that is inaccessible to children • Do not hand over small parts and packaging to children WARNING 5.
Sicherheitshinweise IB-M2HSF-705 Zur Vermeidung körperlicher Schäden, sowie von Sach-, Geräteschäden und Datenverlust beachten Sie bitte folgende Hinweise: Warnstufen Signalwort und Sicherheitszeichen kennzeichnen die Warnstufe und geben einen sofortigen Hinweis auf Wahrscheinlichkeit, Art und Schwere der Folgen, wenn die Maßnahmen zur Vermeidung der Gefahr nicht befolgt werden. GEFAHR warnt vor einer unmittelbar gefährlichen Situation, die zum Tod oder zu schweren Verletzungen führen wird.
Sicherheitshinweise IB-M2HSF-705 • • • • • externe Erwärmung vermeiden und Luftaustausch zulassen Lüfterauslass und passive Kühlkörper freihalten direkte Sonneneinstrahlung auf Gerät/Netzteil vermeiden ausreichend Umgebungsluft für Gerät/Netzteil sicherstellen keine Gegenstände auf dem Gerät/Netzteil abstellen 4.
Manual IB-M2HSF-705 Protect your M.2 SSD! 105 g pure high-performance cooling with great flexibility. Thanks to the clever swivel function, installation in confined spaces is guaranteed. The interplay between heat pipe and fan ensures excellent cooling performance with 23 W TDP, reducing the temperature of your M.2 SSD by up to 40%*. With a volume flow of 2.87 CFM or about 4.9 m³/h and 8500 rpm the generated heat is excellently dissipated by the 30 mm PWM fan. This enables your M.
Manual IB-M2HSF-705 Overview 1 2 5 3 4 6 1. 2. 3. 4. 5. 6. 30 mm 12 V PWM fan with 8500 rpm 22x 0.
Manual IB-M2HSF-705 Installation 1. To change the orientation of the heat sink, loosen the two large screws in the center of the aluminium heat sink. 2. Now tilt the heat sink in the desired direction.
Manual IB-M2HSF-705 3. Now tighten the two large screws to fix the heat sink securely in the desired position. 4. Now loosen the four small screws on the counter plate to remove the heat sink from the counter plate.
Manual IB-M2HSF-705 5. Install both thermal pads. Install the first thermal pad on the counter plate and the second thermal pad on the top of your M.2 SSD. Now gently press the SSD together with the thermal pad on the counter plate. Then press the M.2 SSD together with the counter plate on the bottom of the main heat sink and fix it with all four screws. Note: Make sure that the contacts of the M.2 SSD protrude over the counter plate. Also, when installing a 22x 80 mm M.2 SSD, make sure that the M.
Manual IB-M2HSF-705 6. Carefully insert the M.2 SSD with heat sink into the M.2 slot of your mainboard at an angle of about 30°. Now fix the heat sink and M.2 SSD with the screw provided. Note: Make sure that the M.2 SSD and M.2 socket as well as the supported protocol (e.g. NVMe) match (e.g. M-Key NVMe M.2 SSD and M-Key socket for example on the motherboard). 7. Finally, plug the 4 pin fan connector onto a free 4 pin connector on your motherboard. The fan runs continuously when connected.
Handbuch IB-M2HSF-705 Schützen Sie Ihre M.2 SSD! 105 g pure Hochleistungskühlung bei großer Flexibilität. Dank der durchdachten Schwenkfunktion ist die Installation auch bei beengten Platzverhältnissen gewährleistet. Das Zusammenspiel zwischen Heatpipe und Lüfter sorgt für eine hervorragende Kühlleistung von 23 W TDP, durch die die Temperatur Ihrer M.2 SSD um bis zu 40%* reduziert werden kann. Mit einem Volumenstrom von 2,87 CFM oder ca.
Handbuch IB-M2HSF-705 Überblick 1 2 5 3 4 6 1. 2. 3. 4. 5. 6. 30 mm 12 V Lüfter mit 8500 U/min 22x 0.
Handbuch IB-M2HSF-705 Installation 1. Um die Ausrichtung des Kühlkörpers zu ändern, lösen Sie die beiden großen Schrauben in der Mitte des Aluminiumkühlkörpers. 2. Neigen Sie nun den Kühlkörper in die gewünschte Richtung.
Handbuch IB-M2HSF-705 3. Ziehen Sie nun die beiden großen Schrauben wieder fest, sodass der Kühlkörper sicher in der gewünschten Position bleibt. 4. Lösen Sie nun die vier kleinen Schrauben an der Konterplatte, um den Kühlkörper von der Konterplatte zu entfernen.
Handbuch IB-M2HSF-705 5. Befestigen Sie beide Wärmeleitpads: das erste Wärmeleitpad auf die Konterplatte und das zweite Wärmeleitpad auf die Oberseite Ihrer M.2 SSD. Nun drücken Sie die SSD mitsamt dem Wärmeleitpad auf der Oberseite vorsichtig auf die Konterplatte mit dem zweiten –bereits installierten– Wärmeleitpad. Dann drücken Sie vorsichtig die Konterplatte mit SSD an den Hauptkühlkörper und fixieren Sie diese mit den vier Schrauben. Hinweis: Achten Sie darauf, dass die Kontakte der M.
Handbuch IB-M2HSF-705 6. Stecken Sie die M.2 SSD mit Kühlkörper vorsichtig in einem Winkel von etwa 30° in den M.2 Steckplatz Ihres Mainboards. Fixieren Sie nun Kühlkörper und M.2 SSD mit der mitgelieferten Schraube. Hinweis: Achten Sie darauf, dass M.2 SSD und M.2 Sockel, sowie das unterstützte Protokoll (z.B. NVMe) zueinander passen (z.B. M-Key NVMe M.2 SSD und M-Key Sockel z.B. auf dem Motherboard). 7.
© Copyright 2021 by RaidSonic Technology GmbH. All Rights Reserved. The information contained in this manual is believed to be accurate and reliable. RaidSonic Technology GmbH assumes no responsibility for any errors contained in this manual. RaidSonic Technology GmbH reserves the right to make changes in the specifications and/or design of the above-mentioned product without prior notice.