User's Guide

ManualsBrandsiDARS Pro ManualsCamera & PhotoiDARS Pro Canon Bluetooth Camera Remote

a. Press this

button

Bluetooth

Paired

d4538xxxxxxx

paire

Bluetooth setup

6 Video

Selfie 10 seconds/

remote control

Operation mode

Immediate Release

2-sec. Delay Release

Movie Shooting

a. Movie Shooting

Safety Precautions

Notice

b. Video

1. W/T Function: Usable only with Canon EF-S 18-135mm

f/3.5-5.6 IS USM and PZ-E1

2. 605007 Remote can only be paired to one device at one

time. You will need to re-pair if you wish to switch devices.

3. Please take out the battery if you will not be using the

device for a long time.

4. When your smartphone is paired to the device but not in

camera mode, it is normal setup that clicking the

<Release> button will trigger the increase in volume.

b. Enter the Bluetooth-

setup and Click “Pair”

3 a. Press and hold W/T button

simultaneously for 3-5 seconds

b. the indicator light blinks.

4 You will see a message pop up

that says “iDARS Pro Remote is

paired”. Click Confirm to

complete the pairing.

5 Photo

c. Press to enter

Photo mode

c. Press to enter

Photo mode

b. Press <Release>

take a video

d. Press <Release> to

take a picture

Click Confirm

Confirm

1. Do not try to disassemble, repair or modify the product. If you have any

questions, please contact iDARS Pro customer support service directly

2. Do not immerse the product in water or liquid. Wipe the surface with a

clean cloth to remove water droplets.

3. Do not use this product near flammable and explosive gases to avoid fire.

4. Do not keep this product at a high temperature of over 450 degrees to

avoid overheating.

5. Do not let children use this product alone. Adults need to thoroughly

explain the use of the product and conduct proper supervision.

Before use, please read the following precautions

carefully to avoid any injury.

FCC Warning

Federal Communications Commission Statement

This device complies with FCC Rules Part 15. Operation is subject to the

following two conditions:

• This device may not cause harmful interference.

• This device must accept any interference received, including interference

that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a

class B digital device, pursuant to Part 15 of the Federal Communications

Commission (FCC) rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation. This

equipment generates, uses, and can radiate radio frequency energy and, if

not installed and used in accordance with the instructions, may cause

harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this

equipment causes harmful interference to radio or television reception,

which can be determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by doing one or more of the

following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

FCC Caution

Any changes or modifications not expressly approved by the party

responsible for compliance could void the user‘s authority to operate the

equipment.

The antenna(s) used for this transmitter must not be co-located or operating

in conjunction with any other antenna or transmitter.

Radiation Exposure Statement:

The product comply with the FCC portable RF exposure limit set forth for an

uncontrolled environment and are safe for intended operation as

described in this manual. The further RF exposure reduction can be

achieved if the product can be kept as far as possible from the user body or

set the device to lower output power if such function is available.

b. Remote Shooting

a. Immediate Release

2 Turn on your Canon camera and

enter the Bluetooth page

(Please refer to the pairing guide for

Canon Remote BR-E1 with differ-

ent Canon camera models)

*This picture uses EOS-800D as

reference.

Pairing the Remote Controller

and

Camera

WEBSITE

10F-8,NO.237.Sec.,1, Datong Rd., Xizhi Dist.

New�Taipei City 22161, Taiwan, R. O. C.

(Taiwan Science Park T1)

TEL: 02-2647-1928 ext:120 FAX:02-2647-1930

iDARS Pro Inc.

Compatible models

EOS 6D Mark 2

EOS RP

EOS R

EOS R6

EOS R5

EOS 90D

EOS 77D

EOS 850D, REBEL T8i

EOS 800D, REBEL T7i

EOS 250D

EOS 200D Mark 2

EOS 200D ,REBEL SL2

EOS M6 Mark 2

EOS M200

PowerShot SX70 HS

iPhone all

Andriod Phone

(Does not support SONY

smartphone)

Quick Guide

iDARS Pro

Canon Bluetooth

Camera Remote

Model: 605007-BLK

Introduction

iDARS Pro Canon Bluetooth Camera Remote is a

wireless remote controller compatible with Bluetooth®

(Bluetooth low energy technology). It can pair with

Bluetooth-compatible Canon® digital cameras and

smartphone devices to perform the following

operations (at a istance of 32 ft.in any direction):

● Shooting still photos

● Filming movies

● Focusing with AF

● Zooming (Available only when used with the

Power Zoom Adapter)

Please read this user guide for your camera and

power zoom adapter before use

Specifications

Type

Compliance Standards

Transmission Method

Operating Distance

Power

Dimensions (WxHxD)

Weight

Remote Controller

Bluetooth Specification Version 4.1

GFSK Modulation

Approx. 5m/16.4ft

Lithium button cell battery CR2032

91x11x27mm

17g

Function instructions

1. Release Button

2. Indicator Lamp (Red)

3. <AF> AF Start Button

4. Power Zoom:

<W> Wide-angle Button

<T> Telephoto Button

5. Strap Hole

6. Release Timing/Movie Shooting Switch

< ● > Immediate Release

< 2 > 2-sec. Delay Release

< > Movie Shooting

7. Battery Compartment Cover Screw

8. Battery Compartment Cover

1 a. Open the lid.

b. Place the battery into the device

and close the lid.

2 a. Press and hold the <Release>

and <AF> button simultaneously

for 3-5 seconds

b. the indicator light blinks.

Pairing the Remote Controller

and Smartphone

3 Open the Bluetooth setup on

your smartphone

Bluetooth

a. Press iDARS Pro

Remote to pair

b. Press [Pair]

iDARS Pro Remote

Bluetooth Pairing Request

[iDARS Pro Remote]

would like to pair with

your iPhone

Bluetooth Pairing Request

[iDARS Pro Remote]

would like to pair with

your iPhone

PairCancel

4 You will see [iDARS Pro Remote]

is connected on your

Bluetooth page.

Bluetooth

Connected

iDARS Pro Remote connected

5 Enter PHOTO/ VIDEO mode

Select PHOTO

mode

b. Select VIDEO

mode

c. Press <Release>

to take a photo

VIDEO PHOTO PORTRAIT PANO

Immediate Release

2-sec. Delay Release

Movie Shooting

1 a. Open the lid.

b. Place the battery into the device

and close the lid.

背面

正面