Owner's Manual

ManualsBrandsiDatalink ManualsAudio accessories & installationInterface Harness

Table Of Contents

Install Guide

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certiﬁ ed technician. Logos and trademarks used here in

are the properties of their respective owners.

WARNING

Pressing the printer icon or “quick printing” this document will print

all of the guides in this compilation.

Open the Bookmarks menu and find your vehicle OR scroll

down until you find the install guide for your vehicle.

Print only the pages for your vehicle using the advanced

options in the Print menu.

Install your Maestro RR according to the guide for your vehicle.

HOW TO USE THIS INSTALL GUIDE

SELECT VEHICLE

PRINT PAGES NEEDED

Summary of content (409 pages)

PAGE 1
SELECT VEHICLE PRINT PAGES NEEDED HOW TO USE THIS INSTALL GUIDE 1 Open the Bookmarks menu and find your vehicle OR scroll down until you find the install guide for your vehicle. 2 Print only the pages for your vehicle using the advanced options in the Print menu. 3 Install your Maestro RR according to the guide for your vehicle. WARNING Pressing the printer icon or “quick printing” this document will print all of the guides in this compilation. NOTICE: Automotive Data Solutions Inc.
PAGE 2
INSTALL GUIDE 2013-2016 Scion FR-S Base RETAINS STEERING WHEEL CONTROLS, AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-SU2 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-SUB2-DS ADDITIONAL RESOURCES ACC-uSU2 Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
PAGE 3
Scion FR-S Base 2013-2016 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Installation Instructions 3 Wiring Diagram 4 Radio Wire Reference Chart 5 Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct ﬁrmware for your vehicle and that you carefully review the install guide.
PAGE 4
Scion FR-S Base 2013-2016 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Cut the WHITE, GRAY, GREEN and PURPLE RCA tips. • Connect the wires from aftermarket radio main harness to the SU2 T-harness and match the wire functions. • Remove the factory radio. STEP 2 • Assemble the SU2 T-harness and connect it to the factory radio harness. STEP 3 Note: Connection required if the vehicle is equipped with Starlink telematics and a SOS button.
PAGE 5
Scion FR-S Base 2013-2016 WIRING DIAGRAM STEP 5 STEP 1 PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT. CUT AND REMOVE THE RCA JACKS CONNECT TO AFTERMARKET RADIO WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
PAGE 6
Scion FR-S Base 2013-2016 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Illumination (+) Orange N/A Orange/White Orange/White Reverse Light (+) Purple/White Orange/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green VSS (vehicle speed sensor) (DATA) Pink Green/White Pink Pink Power Antenna (+) Blue Blue Blue N/A Automoti
PAGE 7
Scion FR-S Base 2013-2016 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended. Reset the RR.
PAGE 8
INSTALL GUIDE 2013-2016 Scion FR-S With Amp RETAINS STEERING WHEEL CONTROLS, AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-SU2 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-SUB2-DS ADDITIONAL RESOURCES ACC-uSU2 Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
PAGE 9
Scion FR-S With Amp 2013-2016 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Installation Instructions 3 Wiring Diagram 4 Radio Wire Reference Chart 5 Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct ﬁrmware for your vehicle and that you carefully review the install guide.
PAGE 10
Scion FR-S With Amp 2013-2016 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Cut the WHITE, GRAY, GREEN and PURPLE RCA tips. • Connect the wires from aftermarket radio main harness to the SU2 T-harness and match the wire functions. • Remove the factory radio. STEP 2 • Assemble the SU2 T-harness and connect it to the factory radio harness.
PAGE 11
Scion FR-S With Amp 2013-2016 WIRING DIAGRAM STEP 5 STEP 1 PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT. CUT AND REMOVE THE RCA JACKS WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
PAGE 12
Scion FR-S With Amp 2013-2016 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Illumination (+) Orange N/A Orange/White Orange/White Reverse Light (+) Purple/White Orange/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green VSS (vehicle speed sensor) (DATA) Pink Green/White Pink Pink Power Antenna (+) Blue Blue Blue N/A Auto
PAGE 13
Scion FR-S With Amp 2013-2016 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended. Reset the RR.
PAGE 14
INSTALL GUIDE 2013-2016 Scion FR-S With NAV RETAINS STEERING WHEEL CONTROLS, AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-SU2 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-SUB2-DS ADDITIONAL RESOURCES ACC-uSU2 Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
PAGE 15
Scion FR-S With NAV 2013-2016 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Installation Instructions 3 Wiring Diagram 4 Radio Wire Reference Chart 5 Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct ﬁrmware for your vehicle and that you carefully review the install guide.
PAGE 16
Scion FR-S With NAV 2013-2016 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Cut the WHITE, GRAY, GREEN and PURPLE RCA tips. • Connect the wires from aftermarket radio main harness to the SU2 T-harness and match the wire functions. • Remove the factory radio. STEP 2 • Assemble the SU2 T-harness and connect it to the factory radio harness. STEP 3 Note: Connection required if the vehicle is equipped with Starlink telematics and a SOS button.
PAGE 17
Scion FR-S With NAV 2013-2016 WIRING DIAGRAM STEP 5 STEP 1 PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT. CUT AND REMOVE THE RCA JACKS CONNECT TO AFTERMARKET RADIO WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
PAGE 18
Scion FR-S With NAV 2013-2016 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Illumination (+) Orange N/A Orange/White Orange/White Reverse Light (+) Purple/White Orange/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green VSS (vehicle speed sensor) (DATA) Pink Green/White Pink Pink Power Antenna (+) Blue Blue Blue N/A Auto
PAGE 19
Scion FR-S With NAV 2013-2016 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended. Reset the RR.
PAGE 20
INSTALL GUIDE 2013-2016 Scion FR-S With NAV With Amp RETAINS STEERING WHEEL CONTROLS, AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-SU2 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-SUB2-DS ADDITIONAL RESOURCES ACC-uSU2 Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
PAGE 21
Scion FR-S With NAV With Amp 2013-2016 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
PAGE 22
Scion FR-S With NAV With Amp 2013-2016 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Cut the WHITE, GRAY, GREEN and PURPLE RCA tips. • Connect the wires from aftermarket radio main harness to the SU2 T-harness and match the wire functions. • Remove the factory radio. STEP 2 • Assemble the SU2 T-harness and connect it to the factory radio harness.
PAGE 23
Scion FR-S With NAV With Amp 2013-2016 WIRING DIAGRAM STEP 5 STEP 1 PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT. CUT AND REMOVE THE RCA JACKS WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
PAGE 24
Scion FR-S With NAV With Amp 2013-2016 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Illumination (+) Orange N/A Orange/White Orange/White Reverse Light (+) Purple/White Orange/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green VSS (vehicle speed sensor) (DATA) Pink Green/White Pink Pink Power Antenna (+) Blue Blue Blue
PAGE 25
Scion FR-S With NAV With Amp 2013-2016 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended. Reset the RR.
PAGE 26
INSTALL GUIDE 2013-2019 Subaru BRZ Base RETAINS STEERING WHEEL CONTROLS, AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-SU2 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-SUB2-DS ADDITIONAL RESOURCES ACC-uSU2 Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
PAGE 27
Subaru BRZ Base 2013-2019 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Installation Instructions 3 Wiring Diagram 4 Radio Wire Reference Chart 5 Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct ﬁrmware for your vehicle and that you carefully review the install guide.
PAGE 28
Subaru BRZ Base 2013-2019 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Cut the WHITE, GRAY, GREEN and PURPLE RCA tips. • Connect the wires from aftermarket radio main harness to the SU2 T-harness and match the wire functions. • Remove the factory radio. STEP 2 • Assemble the SU2 T-harness and connect it to the factory radio harness. STEP 3 Note: Connection required if the vehicle is equipped with Starlink telematics and a SOS button.
PAGE 29
Subaru BRZ Base 2013-2019 WIRING DIAGRAM STEP 5 STEP 1 PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT. CUT AND REMOVE THE RCA JACKS CONNECT TO AFTERMARKET RADIO WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
PAGE 30
Subaru BRZ Base 2013-2019 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Illumination (+) Orange N/A Orange/White Orange/White Reverse Light (+) Purple/White Orange/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green VSS (vehicle speed sensor) (DATA) Pink Green/White Pink Pink Power Antenna (+) Blue Blue Blue N/A Automoti
PAGE 31
Subaru BRZ Base 2013-2019 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended. Reset the RR.
PAGE 32
INSTALL GUIDE 2013-2019 Subaru BRZ With Amp RETAINS STEERING WHEEL CONTROLS, AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-SU2 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-SUB2-DS ADDITIONAL RESOURCES ACC-uSU2 Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
PAGE 33
Subaru BRZ With Amp 2013-2019 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Installation Instructions 3 Wiring Diagram 4 Radio Wire Reference Chart 5 Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct ﬁrmware for your vehicle and that you carefully review the install guide.
PAGE 34
Subaru BRZ With Amp 2013-2019 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Cut the WHITE, GRAY, GREEN and PURPLE RCA tips. • Connect the wires from aftermarket radio main harness to the SU2 T-harness and match the wire functions. • Remove the factory radio. STEP 2 • Assemble the SU2 T-harness and connect it to the factory radio harness.
PAGE 35
Subaru BRZ With Amp 2013-2019 WIRING DIAGRAM STEP 5 STEP 1 PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT. CUT AND REMOVE THE RCA JACKS WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
PAGE 36
Subaru BRZ With Amp 2013-2019 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Illumination (+) Orange N/A Orange/White Orange/White Reverse Light (+) Purple/White Orange/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green VSS (vehicle speed sensor) (DATA) Pink Green/White Pink Pink Power Antenna (+) Blue Blue Blue N/A Auto
PAGE 37
Subaru BRZ With Amp 2013-2019 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended. Reset the RR.
PAGE 38
INSTALL GUIDE 2013-2019 Subaru BRZ With NAV RETAINS STEERING WHEEL CONTROLS, AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-SU2 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-SUB2-DS ADDITIONAL RESOURCES ACC-uSU2 Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
PAGE 39
Subaru BRZ With NAV 2013-2019 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Installation Instructions 3 Wiring Diagram 4 Radio Wire Reference Chart 5 Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct ﬁrmware for your vehicle and that you carefully review the install guide.
PAGE 40
Subaru BRZ With NAV 2013-2019 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Cut the WHITE, GRAY, GREEN and PURPLE RCA tips. • Connect the wires from aftermarket radio main harness to the SU2 T-harness and match the wire functions. • Remove the factory radio. STEP 2 • Assemble the SU2 T-harness and connect it to the factory radio harness. STEP 3 Note: Connection required if the vehicle is equipped with Starlink telematics and a SOS button.
PAGE 41
Subaru BRZ With NAV 2013-2019 WIRING DIAGRAM STEP 5 STEP 1 PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT. CUT AND REMOVE THE RCA JACKS CONNECT TO AFTERMARKET RADIO WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
PAGE 42
Subaru BRZ With NAV 2013-2019 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Illumination (+) Orange N/A Orange/White Orange/White Reverse Light (+) Purple/White Orange/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green VSS (vehicle speed sensor) (DATA) Pink Green/White Pink Pink Power Antenna (+) Blue Blue Blue N/A Auto
PAGE 43
Subaru BRZ With NAV 2013-2019 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended. Reset the RR.
PAGE 44
INSTALL GUIDE 2013-2019 Subaru BRZ With NAV With Amp RETAINS STEERING WHEEL CONTROLS, AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-SU2 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-SUB2-DS ADDITIONAL RESOURCES ACC-uSU2 Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
PAGE 45
Subaru BRZ With NAV With Amp 2013-2019 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
PAGE 46
Subaru BRZ With NAV With Amp 2013-2019 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Cut the WHITE, GRAY, GREEN and PURPLE RCA tips. • Connect the wires from aftermarket radio main harness to the SU2 T-harness and match the wire functions. • Remove the factory radio. STEP 2 • Assemble the SU2 T-harness and connect it to the factory radio harness.
PAGE 47
Subaru BRZ With NAV With Amp 2013-2019 WIRING DIAGRAM STEP 5 STEP 1 PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT. CUT AND REMOVE THE RCA JACKS WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
PAGE 48
Subaru BRZ With NAV With Amp 2013-2019 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Illumination (+) Orange N/A Orange/White Orange/White Reverse Light (+) Purple/White Orange/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green VSS (vehicle speed sensor) (DATA) Pink Green/White Pink Pink Power Antenna (+) Blue Blue Blue
PAGE 49
Subaru BRZ With NAV With Amp 2013-2019 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended. Reset the RR.
PAGE 50
INSTALL GUIDE 2016-2017 Subaru Forester with 6.2 inch screen RETAINS STEERING WHEEL CONTROLS, AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-SU2 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-SUB2-DS ADDITIONAL RESOURCES ACC-uSU2 Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
PAGE 51
Subaru Forester with 6.2 inch screen 2016-2017 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
PAGE 52
Subaru Forester with 6.2 inch screen 2016-2017 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Cut the WHITE, GRAY, GREEN and PURPLE RCA tips. • Connect the wires from aftermarket radio main harness to the SU2 T-harness and match the wire functions. • Remove the factory radio. STEP 2 • Assemble the SU2 T-harness and connect it to the factory radio harness. STEP 3 Note: Connection required if the vehicle is equipped with Starlink telematics and a SOS button.
PAGE 53
Subaru Forester with 6.2 inch screen 2016-2017 WIRING DIAGRAM STEP 5 STEP 1 PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT. CUT AND REMOVE THE RCA JACKS CONNECT TO AFTERMARKET RADIO WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
PAGE 54
Subaru Forester with 6.
PAGE 55
Subaru Forester with 6.2 inch screen 2016-2017 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended.
PAGE 56
INSTALL GUIDE 2016-2017 Subaru Forester with 6.2 inch screen and Harman Kardon RETAINS STEERING WHEEL CONTROLS, AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-SU2 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-SUB2-DS ADDITIONAL RESOURCES ACC-uSU2 Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
PAGE 57
Subaru Forester with 6.2 inch screen and Harman Kardon 2016-2017 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
PAGE 58
Subaru Forester with 6.2 inch screen and Harman Kardon 2016-2017 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires from aftermarket radio main harness to the SU2 T-harness and match the wire functions. • Remove the factory radio. STEP 2 • Assemble the SU2 T-harness and connect it to the factory radio harness. STEP 3 Note: Connection required if the vehicle is equipped with Starlink telematics and a SOS button.
PAGE 59
Subaru Forester with 6.2 inch screen and Harman Kardon 2016-2017 WIRING DIAGRAM STEP 5 STEP 1 WHITE WHITE/BLACK GRAY GRAY/BLACK GREEN GREEN/BLACK PURPLE PURPLE/BLACK RCA CABLES LF RCA INPUT PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT. RF RCA INPUT LR RCA INPUT CONNECT TO AFTERMARKET RADIO RR RCA INPUT MAIN HARNESS BLUE/WHITE - AMP.
PAGE 60
Subaru Forester with 6.
PAGE 61
Subaru Forester with 6.2 inch screen and Harman Kardon 2016-2017 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps.
PAGE 62
INSTALL GUIDE 2018 Subaru Forester with 6.5 inch screen RETAINS STEERING WHEEL CONTROLS, AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-SU2 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-SUB2-DS ADDITIONAL RESOURCES ACC-uSU2 Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
PAGE 63
Subaru Forester with 6.5 inch screen 2018 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
PAGE 64
Subaru Forester with 6.5 inch screen 2018 INSTALLATION INSTRUCTIONS STEP 6 STEP 1 • Connect all the harnesses to the Maestro RR module then test your installation. • Unbox the aftermarket radio and locate its main harness. • Cut the WHITE, GRAY, GREEN and PURPLE RCA tips. • Connect the wires from aftermarket radio main harness to the SU2 T-harness and match the wire functions. • Remove the factory radio. STEP 2 • Assemble the SU2 T-harness and connect it to the factory radio harness.
PAGE 65
Subaru Forester with 6.5 inch screen 2018 WIRING DIAGRAM STEP 5 STEP 1 PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT. CUT AND REMOVE THE RCA JACKS WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
PAGE 66
Subaru Forester with 6.
PAGE 67
Subaru Forester with 6.5 inch screen 2018 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended. Reset the RR.
PAGE 68
INSTALL GUIDE 2018 Subaru Forester with 6.5 inch screen and Harman Kardon RETAINS STEERING WHEEL CONTROLS, AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-SU2 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-SUB2-DS ADDITIONAL RESOURCES ACC-uSU2 Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
PAGE 69
Subaru Forester with 6.5 inch screen and Harman Kardon 2018 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
PAGE 70
Subaru Forester with 6.5 inch screen and Harman Kardon 2018 INSTALLATION INSTRUCTIONS STEP 6 STEP 1 • Connect all the harnesses to the Maestro RR module then test your installation. • Unbox the aftermarket radio and locate its main harness. • Connect the wires from aftermarket radio main harness to the SU2 T-harness and match the wire functions. • Remove the factory radio. STEP 2 • Assemble the SU2 T-harness and connect it to the factory radio harness.
PAGE 71
Subaru Forester with 6.5 inch screen and Harman Kardon 2018 WIRING DIAGRAM STEP 5 STEP 1 WHITE WHITE/BLACK GRAY GRAY/BLACK GREEN GREEN/BLACK PURPLE PURPLE/BLACK PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT. LF RCA INPUT RF RCA INPUT LR RCA INPUT CONNECT TO AFTERMARKET RADIO RR RCA INPUT MAIN HARNESS BLUE/WHITE - AMP.
PAGE 72
Subaru Forester with 6.
PAGE 73
Subaru Forester with 6.5 inch screen and Harman Kardon 2018 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps.
PAGE 74
INSTALL GUIDE 2016-2017 Subaru Forester with 7 inch screen RETAINS STEERING WHEEL CONTROLS, AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-SU2 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-SUB2-DS ADDITIONAL RESOURCES ACC-uSU2 Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
PAGE 75
Subaru Forester with 7 inch screen 2016-2017 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
PAGE 76
Subaru Forester with 7 inch screen 2016-2017 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Cut the WHITE, GRAY, GREEN and PURPLE RCA tips. • Connect the wires from aftermarket radio main harness to the SU2 T-harness and match the wire functions. • Remove the factory radio. STEP 2 • Assemble the SU2 T-harness and connect it to the factory radio harness. STEP 3 Note: Connection required if the vehicle is equipped with Starlink telematics and a SOS button.
PAGE 77
Subaru Forester with 7 inch screen 2016-2017 WIRING DIAGRAM STEP 5 STEP 1 PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT. CUT AND REMOVE THE RCA JACKS CONNECT TO AFTERMARKET RADIO WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
PAGE 78
Subaru Forester with 7 inch screen 2016-2017 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Illumination (+) Orange N/A Orange/White Orange/White Reverse Light (+) Purple/White Orange/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green VSS (vehicle speed sensor) (DATA) Pink Green/White Pink Pink Power Antenna (+) Blue Blue
PAGE 79
Subaru Forester with 7 inch screen 2016-2017 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended.
PAGE 80
INSTALL GUIDE 2018 Subaru Forester with 7 inch screen RETAINS STEERING WHEEL CONTROLS, AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-SU2 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-SUB2-DS ADDITIONAL RESOURCES ACC-uSU2 Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
PAGE 81
Subaru Forester with 7 inch screen 2018 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
PAGE 82
Subaru Forester with 7 inch screen 2018 INSTALLATION INSTRUCTIONS STEP 6 STEP 1 • Connect all the harnesses to the Maestro RR module then test your installation. • Unbox the aftermarket radio and locate its main harness. • Cut the WHITE, GRAY, GREEN and PURPLE RCA tips. • Connect the wires from aftermarket radio main harness to the SU2 T-harness and match the wire functions. • Remove the factory radio. STEP 2 • Assemble the SU2 T-harness and connect it to the factory radio harness.
PAGE 83
Subaru Forester with 7 inch screen 2018 WIRING DIAGRAM STEP 5 STEP 1 PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT. CUT AND REMOVE THE RCA JACKS WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
PAGE 84
Subaru Forester with 7 inch screen 2018 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Illumination (+) Orange N/A Orange/White Orange/White Reverse Light (+) Purple/White Orange/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green VSS (vehicle speed sensor) (DATA) Pink Green/White Pink Pink Power Antenna (+) Blue Blue Blue
PAGE 85
Subaru Forester with 7 inch screen 2018 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended. Reset the RR.
PAGE 86
INSTALL GUIDE 2016-2017 Subaru Forester with 7 inch screen and Harman Kardon RETAINS STEERING WHEEL CONTROLS, AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-SU2 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-SUB2-DS ADDITIONAL RESOURCES ACC-uSU2 Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
PAGE 87
Subaru Forester with 7 inch screen and Harman Kardon 2016-2017 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
PAGE 88
Subaru Forester with 7 inch screen and Harman Kardon 2016-2017 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires from aftermarket radio main harness to the SU2 T-harness and match the wire functions. • Remove the factory radio. STEP 2 • Assemble the SU2 T-harness and connect it to the factory radio harness. STEP 3 Note: Connection required if the vehicle is equipped with Starlink telematics and a SOS button.
PAGE 89
Subaru Forester with 7 inch screen and Harman Kardon 2016-2017 WIRING DIAGRAM STEP 5 STEP 1 WHITE WHITE/BLACK GRAY GRAY/BLACK GREEN GREEN/BLACK PURPLE PURPLE/BLACK PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT. LF RCA INPUT RF RCA INPUT LR RCA INPUT CONNECT TO AFTERMARKET RADIO RR RCA INPUT MAIN HARNESS BLUE/WHITE - AMP.
PAGE 90
Subaru Forester with 7 inch screen and Harman Kardon 2016-2017 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Illumination (+) Orange N/A Orange/White Orange/White Reverse Light (+) Purple/White Orange/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green VSS (vehicle speed sensor) (DATA) Pink Green/White Pink Pink Power Antenna
PAGE 91
Subaru Forester with 7 inch screen and Harman Kardon 2016-2017 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps.
PAGE 92
INSTALL GUIDE 2018 Subaru Forester with 7 inch screen and Harman Kardon RETAINS STEERING WHEEL CONTROLS, AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-SU2 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-SUB2-DS ADDITIONAL RESOURCES ACC-uSU2 Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
PAGE 93
Subaru Forester with 7 inch screen and Harman Kardon 2018 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
PAGE 94
Subaru Forester with 7 inch screen and Harman Kardon 2018 INSTALLATION INSTRUCTIONS STEP 6 STEP 1 • Connect all the harnesses to the Maestro RR module then test your installation. • Unbox the aftermarket radio and locate its main harness. • Connect the wires from aftermarket radio main harness to the SU2 T-harness and match the wire functions. • Remove the factory radio. STEP 2 • Assemble the SU2 T-harness and connect it to the factory radio harness. • Locate the 28 pin connector on the SU2 T-harness.
PAGE 95
Subaru Forester with 7 inch screen and Harman Kardon 2018 WIRING DIAGRAM STEP 5 STEP 1 WHITE WHITE/BLACK GRAY GRAY/BLACK GREEN GREEN/BLACK PURPLE PURPLE/BLACK PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT. LF RCA INPUT RF RCA INPUT LR RCA INPUT CONNECT TO AFTERMARKET RADIO RR RCA INPUT MAIN HARNESS BLUE/WHITE - AMP.
PAGE 96
Subaru Forester with 7 inch screen and Harman Kardon 2018 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Illumination (+) Orange N/A Orange/White Orange/White Reverse Light (+) Purple/White Orange/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green VSS (vehicle speed sensor) (DATA) Pink Green/White Pink Pink Power Antenna (+)
PAGE 97
Subaru Forester with 7 inch screen and Harman Kardon 2018 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps.
PAGE 98
INSTALL GUIDE 2014-2015 Subaru Forester with NAV RETAINS STEERING WHEEL CONTROLS, AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-SU2 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-SUB2-DS ADDITIONAL RESOURCES ACC-uSU2 Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
PAGE 99
Subaru Forester with NAV 2014-2015 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
PAGE 100
Subaru Forester with NAV 2014-2015 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Cut the WHITE, GRAY, GREEN and PURPLE RCA tips. • Connect the wires from aftermarket radio main harness to the SU2 T-harness and match the wire functions. • Remove the factory radio. STEP 2 • Assemble the SU2 T-harness and connect it to the factory radio harness. STEP 3 • Plug the OBDII connector into the OBDII of the vehicle, under driver dash.
PAGE 101
Subaru Forester with NAV 2014-2015 WIRING DIAGRAM STEP 4 STEP 1 PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT. CUT AND REMOVE THE RCA JACKS CONNECT TO AFTERMARKET RADIO WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
PAGE 102
Subaru Forester with NAV 2014-2015 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Illumination (+) Orange N/A Orange/White Orange/White Reverse Light (+) Purple/White Orange/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green VSS (vehicle speed sensor) (DATA) Pink Green/White Pink Pink Power Antenna (+) Blue Blue Blue N/A
PAGE 103
Subaru Forester with NAV 2014-2015 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended. Reset the RR.
PAGE 104
INSTALL GUIDE 2014-2015 Subaru Forester with NAV and Harman Kardon RETAINS STEERING WHEEL CONTROLS, AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-SU2 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-SUB2-DS ADDITIONAL RESOURCES ACC-uSU2 Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
PAGE 105
Subaru Forester with NAV and Harman Kardon 2014-2015 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
PAGE 106
Subaru Forester with NAV and Harman Kardon 2014-2015 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires from aftermarket radio main harness to the SU2 T-harness and match the wire functions. • Remove the factory radio. STEP 2 • Assemble the SU2 T-harness and connect it to the factory radio harness. STEP 3 • Plug the OBDII connector into the OBDII of the vehicle, under driver dash.
PAGE 107
Subaru Forester with NAV and Harman Kardon 2014-2015 WIRING DIAGRAM STEP 4 STEP 1 WHITE WHITE/BLACK GRAY GRAY/BLACK GREEN GREEN/BLACK PURPLE PURPLE/BLACK PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT. LF RCA INPUT RF RCA INPUT LR RCA INPUT CONNECT TO AFTERMARKET RADIO RR RCA INPUT MAIN HARNESS BLUE/WHITE - AMP.
PAGE 108
Subaru Forester with NAV and Harman Kardon 2014-2015 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Illumination (+) Orange N/A Orange/White Orange/White Reverse Light (+) Purple/White Orange/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green VSS (vehicle speed sensor) (DATA) Pink Green/White Pink Pink Power Antenna (+) Blue
PAGE 109
Subaru Forester with NAV and Harman Kardon 2014-2015 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended.
PAGE 110
INSTALL GUIDE 2012 Subaru Forester with NAV and SD card RETAINS STEERING WHEEL CONTROLS, AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-SU2 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-SUB2-DS ADDITIONAL RESOURCES ACC-uSU2 Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
PAGE 111
Subaru Forester with NAV and SD card 2012 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
PAGE 112
Subaru Forester with NAV and SD card 2012 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Cut the WHITE, GRAY, GREEN and PURPLE RCA tips. • Connect the wires from aftermarket radio main harness to the SU2 T-harness and match the wire functions. • Remove the factory radio. STEP 2 • Assemble the SU2 T-harness and connect it to the factory radio harness. STEP 3 • Plug the OBDII connector into the OBDII of the vehicle, under driver dash.
PAGE 113
Subaru Forester with NAV and SD card 2012 WIRING DIAGRAM STEP 4 STEP 1 PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT. CUT AND REMOVE THE RCA JACKS CONNECT TO AFTERMARKET RADIO WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
PAGE 114
Subaru Forester with NAV and SD card 2012 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Illumination (+) Orange N/A Orange/White Orange/White Reverse Light (+) Purple/White Orange/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green VSS (vehicle speed sensor) (DATA) Pink Green/White Pink Pink Power Antenna (+) Blue Blue Blu
PAGE 115
Subaru Forester with NAV and SD card 2012 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended. Reset the RR.
PAGE 116
INSTALL GUIDE 2013 Subaru Forester with NAV and USB RETAINS STEERING WHEEL CONTROLS, AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-SU2 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-SUB2-DS ADDITIONAL RESOURCES ACC-uSU2 Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
PAGE 117
Subaru Forester with NAV and USB 2013 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
PAGE 118
Subaru Forester with NAV and USB 2013 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Cut the WHITE, GRAY, GREEN and PURPLE RCA tips. • Connect the wires from aftermarket radio main harness to the SU2 T-harness and match the wire functions. • Remove the factory radio. STEP 2 • Assemble the SU2 T-harness and connect it to the factory radio harness. STEP 3 • Plug the OBDII connector into the OBDII of the vehicle, under driver dash.
PAGE 119
Subaru Forester with NAV and USB 2013 WIRING DIAGRAM STEP 4 STEP 1 PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT. CUT AND REMOVE THE RCA JACKS CONNECT TO AFTERMARKET RADIO WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
PAGE 120
Subaru Forester with NAV and USB 2013 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Illumination (+) Orange N/A Orange/White Orange/White Reverse Light (+) Purple/White Orange/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green VSS (vehicle speed sensor) (DATA) Pink Green/White Pink Pink Power Antenna (+) Blue Blue Blue N
PAGE 121
Subaru Forester with NAV and USB 2013 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended. Reset the RR.
PAGE 122
INSTALL GUIDE 2015-2016 Subaru Impreza with 6.2 inch screen RETAINS STEERING WHEEL CONTROLS, AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-SU2 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-SUB2-DS ADDITIONAL RESOURCES ACC-uSU2 Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
PAGE 123
Subaru Impreza with 6.2 inch screen 2015-2016 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
PAGE 124
Subaru Impreza with 6.2 inch screen 2015-2016 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Cut the WHITE, GRAY, GREEN and PURPLE RCA tips. • Connect the wires from aftermarket radio main harness to the SU2 T-harness and match the wire functions. • Remove the factory radio. STEP 2 • Assemble the SU2 T-harness and connect it to the factory radio harness. STEP 3 Note: Connection required if the vehicle is equipped with Starlink telematics and a SOS button.
PAGE 125
Subaru Impreza with 6.2 inch screen 2015-2016 WIRING DIAGRAM STEP 5 STEP 1 PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT. CUT AND REMOVE THE RCA JACKS CONNECT TO AFTERMARKET RADIO WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
PAGE 126
Subaru Impreza with 6.
PAGE 127
Subaru Impreza with 6.2 inch screen 2015-2016 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended.
PAGE 128
INSTALL GUIDE 2015-2016 Subaru Impreza with 6.2 inch screen and Harman Kardon RETAINS STEERING WHEEL CONTROLS, AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-SU2 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-SUB2-DS ADDITIONAL RESOURCES ACC-uSU2 Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
PAGE 129
Subaru Impreza with 6.2 inch screen and Harman Kardon 2015-2016 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
PAGE 130
Subaru Impreza with 6.2 inch screen and Harman Kardon 2015-2016 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires from aftermarket radio main harness to the SU2 T-harness and match the wire functions. • Remove the factory radio. STEP 2 • Assemble the SU2 T-harness and connect it to the factory radio harness. STEP 3 Note: Connection required if the vehicle is equipped with Starlink telematics and a SOS button.
PAGE 131
Subaru Impreza with 6.2 inch screen and Harman Kardon 2015-2016 WIRING DIAGRAM STEP 5 STEP 1 WHITE WHITE/BLACK GRAY GRAY/BLACK GREEN GREEN/BLACK PURPLE PURPLE/BLACK RCA CABLES LF RCA INPUT PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT. RF RCA INPUT LR RCA INPUT CONNECT TO AFTERMARKET RADIO RR RCA INPUT MAIN HARNESS BLUE/WHITE - AMP.
PAGE 132
Subaru Impreza with 6.
PAGE 133
Subaru Impreza with 6.2 inch screen and Harman Kardon 2015-2016 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps.
PAGE 134
INSTALL GUIDE 2015-2016 Subaru Impreza with 7 inch screen RETAINS STEERING WHEEL CONTROLS, AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-SU2 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-SUB2-DS ADDITIONAL RESOURCES ACC-uSU2 Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
PAGE 135
Subaru Impreza with 7 inch screen 2015-2016 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
PAGE 136
Subaru Impreza with 7 inch screen 2015-2016 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Cut the WHITE, GRAY, GREEN and PURPLE RCA tips. • Connect the wires from aftermarket radio main harness to the SU2 T-harness and match the wire functions. • Remove the factory radio. STEP 2 • Assemble the SU2 T-harness and connect it to the factory radio harness. STEP 3 Note: Connection required if the vehicle is equipped with Starlink telematics and a SOS button.
PAGE 137
Subaru Impreza with 7 inch screen 2015-2016 WIRING DIAGRAM STEP 5 STEP 1 PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT. CUT AND REMOVE THE RCA JACKS CONNECT TO AFTERMARKET RADIO WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
PAGE 138
Subaru Impreza with 7 inch screen 2015-2016 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Illumination (+) Orange N/A Orange/White Orange/White Reverse Light (+) Purple/White Orange/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green VSS (vehicle speed sensor) (DATA) Pink Green/White Pink Pink Power Antenna (+) Blue Blue B
PAGE 139
Subaru Impreza with 7 inch screen 2015-2016 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended.
PAGE 140
INSTALL GUIDE 2015-2016 Subaru Impreza with 7 inch screen and Harman Kardon RETAINS STEERING WHEEL CONTROLS, AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-SU2 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-SUB2-DS ADDITIONAL RESOURCES ACC-uSU2 Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
PAGE 141
Subaru Impreza with 7 inch screen and Harman Kardon 2015-2016 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
PAGE 142
Subaru Impreza with 7 inch screen and Harman Kardon 2015-2016 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires from aftermarket radio main harness to the SU2 T-harness and match the wire functions. • Remove the factory radio. STEP 2 • Assemble the SU2 T-harness and connect it to the factory radio harness. STEP 3 Note: Connection required if the vehicle is equipped with Starlink telematics and a SOS button.
PAGE 143
Subaru Impreza with 7 inch screen and Harman Kardon 2015-2016 WIRING DIAGRAM STEP 5 STEP 1 WHITE WHITE/BLACK GRAY GRAY/BLACK GREEN GREEN/BLACK PURPLE PURPLE/BLACK PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT. LF RCA INPUT RF RCA INPUT LR RCA INPUT CONNECT TO AFTERMARKET RADIO RR RCA INPUT MAIN HARNESS BLUE/WHITE - AMP.
PAGE 144
Subaru Impreza with 7 inch screen and Harman Kardon 2015-2016 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Illumination (+) Orange N/A Orange/White Orange/White Reverse Light (+) Purple/White Orange/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green VSS (vehicle speed sensor) (DATA) Pink Green/White Pink Pink Power Antenna
PAGE 145
Subaru Impreza with 7 inch screen and Harman Kardon 2015-2016 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps.
PAGE 146
INSTALL GUIDE 2012-2014 Subaru Impreza with NAV and Harman Kardon and OEM camera on radio RETAINS STEERING WHEEL CONTROLS, AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-SU2 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-SUB2-DS ADDITIONAL RESOURCES ACC-uSU2 Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc
PAGE 147
Subaru Impreza with NAV and Harman Kardon and OEM camera on radio 2012-2014 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
PAGE 148
Subaru Impreza with NAV and Harman Kardon and OEM camera on radio 2012-2014 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires from aftermarket radio main harness to the SU2 T-harness and match the wire functions. • Remove the factory radio. STEP 2 • Assemble the SU2 T-harness and connect it to the factory radio harness. STEP 3 • Plug the OBDII connector into the OBDII of the vehicle, under driver dash.
PAGE 149
Subaru Impreza with NAV and Harman Kardon and OEM camera on radio 2012-2014 WIRING DIAGRAM STEP 4 STEP 1 WHITE WHITE/BLACK GRAY GRAY/BLACK GREEN GREEN/BLACK PURPLE PURPLE/BLACK PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT. LF RCA INPUT RF RCA INPUT LR RCA INPUT CONNECT TO AFTERMARKET RADIO RR RCA INPUT MAIN HARNESS BLUE/WHITE - AMP.
PAGE 150
Subaru Impreza with NAV and Harman Kardon and OEM camera on radio 2012-2014 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Illumination (+) Orange N/A Orange/White Orange/White Reverse Light (+) Purple/White Orange/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green VSS (vehicle speed sensor) (DATA) Pink Green/White Pink Pink P
PAGE 151
Subaru Impreza with NAV and Harman Kardon and OEM camera on radio 2012-2014 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps.
PAGE 152
INSTALL GUIDE 2012-2014 Subaru Impreza with NAV and Harman Kardon and OEM camera on secondary display RETAINS STEERING WHEEL CONTROLS, AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-SU2 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-SUB2-DS ADDITIONAL RESOURCES ACC-uSU2 Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data S
PAGE 153
Subaru Impreza with NAV and Harman Kardon and OEM camera on secondary display 2012-2014 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
PAGE 154
Subaru Impreza with NAV and Harman Kardon and OEM camera on secondary display 2012-2014 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires from aftermarket radio main harness to the SU2 T-harness and match the wire functions. • Remove the factory radio. STEP 2 • Assemble the SU2 T-harness and connect it to the factory radio harness. STEP 3 • Plug the OBDII connector into the OBDII of the vehicle, under driver dash.
PAGE 155
Subaru Impreza with NAV and Harman Kardon and OEM camera on secondary display 2012-2014 WIRING DIAGRAM STEP 4 STEP 1 WHITE WHITE/BLACK GRAY GRAY/BLACK GREEN GREEN/BLACK PURPLE PURPLE/BLACK PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT. LF RCA INPUT RF RCA INPUT LR RCA INPUT CONNECT TO AFTERMARKET RADIO RR RCA INPUT MAIN HARNESS BLUE/WHITE - AMP.
PAGE 156
Subaru Impreza with NAV and Harman Kardon and OEM camera on secondary display 2012-2014 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Illumination (+) Orange N/A Orange/White Orange/White Reverse Light (+) Purple/White Orange/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green VSS (vehicle speed sensor) (DATA) Pink Green/White P
PAGE 157
Subaru Impreza with NAV and Harman Kardon and OEM camera on secondary display 2012-2014 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps.
PAGE 158
INSTALL GUIDE 2012-2014 Subaru Impreza with NAV and OEM camera on radio RETAINS STEERING WHEEL CONTROLS, AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-SU2 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-SUB2-DS ADDITIONAL RESOURCES ACC-uSU2 Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
PAGE 159
Subaru Impreza with NAV and OEM camera on radio 2012-2014 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
PAGE 160
Subaru Impreza with NAV and OEM camera on radio 2012-2014 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Cut the WHITE, GRAY, GREEN and PURPLE RCA tips. • Connect the wires from aftermarket radio main harness to the SU2 T-harness and match the wire functions. • Remove the factory radio. STEP 2 • Assemble the SU2 T-harness and connect it to the factory radio harness. STEP 3 • Plug the OBDII connector into the OBDII of the vehicle, under driver dash.
PAGE 161
Subaru Impreza with NAV and OEM camera on radio 2012-2014 WIRING DIAGRAM STEP 4 STEP 1 PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT. CUT AND REMOVE THE RCA JACKS CONNECT TO AFTERMARKET RADIO WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
PAGE 162
Subaru Impreza with NAV and OEM camera on radio 2012-2014 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Illumination (+) Orange N/A Orange/White Orange/White Reverse Light (+) Purple/White Orange/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green VSS (vehicle speed sensor) (DATA) Pink Green/White Pink Pink Power Antenna (+)
PAGE 163
Subaru Impreza with NAV and OEM camera on radio 2012-2014 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps.
PAGE 164
INSTALL GUIDE 2012-2014 Subaru Impreza with NAV and OEM camera on secondary display RETAINS STEERING WHEEL CONTROLS, AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-SU2 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-SUB2-DS ADDITIONAL RESOURCES ACC-uSU2 Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
PAGE 165
Subaru Impreza with NAV and OEM camera on secondary display 2012-2014 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
PAGE 166
Subaru Impreza with NAV and OEM camera on secondary display 2012-2014 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Cut the WHITE, GRAY, GREEN and PURPLE RCA tips. • Connect the wires from aftermarket radio main harness to the SU2 T-harness and match the wire functions. • Remove the factory radio. STEP 2 • Assemble the SU2 T-harness and connect it to the factory radio harness.
PAGE 167
Subaru Impreza with NAV and OEM camera on secondary display 2012-2014 WIRING DIAGRAM STEP 4 STEP 1 PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT. CUT AND REMOVE THE RCA JACKS CONNECT TO AFTERMARKET RADIO WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
PAGE 168
Subaru Impreza with NAV and OEM camera on secondary display 2012-2014 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Illumination (+) Orange N/A Orange/White Orange/White Reverse Light (+) Purple/White Orange/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green VSS (vehicle speed sensor) (DATA) Pink Green/White Pink Pink Power A
PAGE 169
Subaru Impreza with NAV and OEM camera on secondary display 2012-2014 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps.
PAGE 170
INSTALL GUIDE 2015-2017 Subaru Legacy with 6.2 inch screen RETAINS STEERING WHEEL CONTROLS, AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-SU2 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-SUB2-DS ADDITIONAL RESOURCES ACC-uSU2 Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
PAGE 171
Subaru Legacy with 6.2 inch screen 2015-2017 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
PAGE 172
Subaru Legacy with 6.2 inch screen 2015-2017 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Cut the WHITE, GRAY, GREEN and PURPLE RCA tips. • Connect the wires from aftermarket radio main harness to the SU2 T-harness and match the wire functions. • Remove the factory radio. STEP 2 • Assemble the SU2 T-harness and connect it to the factory radio harness. STEP 3 Note: Connection required if the vehicle is equipped with Starlink telematics and a SOS button.
PAGE 173
Subaru Legacy with 6.2 inch screen 2015-2017 WIRING DIAGRAM STEP 5 STEP 1 PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT. CUT AND REMOVE THE RCA JACKS CONNECT TO AFTERMARKET RADIO WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
PAGE 174
Subaru Legacy with 6.
PAGE 175
Subaru Legacy with 6.2 inch screen 2015-2017 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended.
PAGE 176
INSTALL GUIDE 2015-2017 Subaru Legacy with 6.2 inch screen and Harman Kardon RETAINS STEERING WHEEL CONTROLS, AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-SU2 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-SUB2-DS ADDITIONAL RESOURCES ACC-uSU2 Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
PAGE 177
Subaru Legacy with 6.2 inch screen and Harman Kardon 2015-2017 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
PAGE 178
Subaru Legacy with 6.2 inch screen and Harman Kardon 2015-2017 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires from aftermarket radio main harness to the SU2 T-harness and match the wire functions. • Remove the factory radio. STEP 2 • Assemble the SU2 T-harness and connect it to the factory radio harness. STEP 3 Note: Connection required if the vehicle is equipped with Starlink telematics and a SOS button.
PAGE 179
Subaru Legacy with 6.2 inch screen and Harman Kardon 2015-2017 WIRING DIAGRAM STEP 5 STEP 1 WHITE WHITE/BLACK GRAY GRAY/BLACK GREEN GREEN/BLACK PURPLE PURPLE/BLACK RCA CABLES LF RCA INPUT PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT. RF RCA INPUT LR RCA INPUT CONNECT TO AFTERMARKET RADIO RR RCA INPUT MAIN HARNESS BLUE/WHITE - AMP.
PAGE 180
Subaru Legacy with 6.
PAGE 181
Subaru Legacy with 6.2 inch screen and Harman Kardon 2015-2017 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps.
PAGE 182
INSTALL GUIDE 2015-2017 Subaru Legacy with 7 inch screen RETAINS STEERING WHEEL CONTROLS, AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-SU2 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-SUB2-DS ADDITIONAL RESOURCES ACC-uSU2 Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
PAGE 183
Subaru Legacy with 7 inch screen 2015-2017 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
PAGE 184
Subaru Legacy with 7 inch screen 2015-2017 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Cut the WHITE, GRAY, GREEN and PURPLE RCA tips. • Connect the wires from aftermarket radio main harness to the SU2 T-harness and match the wire functions. • Remove the factory radio. STEP 2 • Assemble the SU2 T-harness and connect it to the factory radio harness. STEP 3 Note: Connection required if the vehicle is equipped with Starlink telematics and a SOS button.
PAGE 185
Subaru Legacy with 7 inch screen 2015-2017 WIRING DIAGRAM STEP 5 STEP 1 PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT. CUT AND REMOVE THE RCA JACKS CONNECT TO AFTERMARKET RADIO WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
PAGE 186
Subaru Legacy with 7 inch screen 2015-2017 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Illumination (+) Orange N/A Orange/White Orange/White Reverse Light (+) Purple/White Orange/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green VSS (vehicle speed sensor) (DATA) Pink Green/White Pink Pink Power Antenna (+) Blue Blue Bl
PAGE 187
Subaru Legacy with 7 inch screen 2015-2017 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended.
PAGE 188
INSTALL GUIDE 2015-2017 Subaru Legacy with 7 inch screen and Harman Kardon RETAINS STEERING WHEEL CONTROLS, AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-SU2 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-SUB2-DS ADDITIONAL RESOURCES ACC-uSU2 Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
PAGE 189
Subaru Legacy with 7 inch screen and Harman Kardon 2015-2017 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
PAGE 190
Subaru Legacy with 7 inch screen and Harman Kardon 2015-2017 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires from aftermarket radio main harness to the SU2 T-harness and match the wire functions. • Remove the factory radio. STEP 2 • Assemble the SU2 T-harness and connect it to the factory radio harness. STEP 3 Note: Connection required if the vehicle is equipped with Starlink telematics and a SOS button.
PAGE 191
Subaru Legacy with 7 inch screen and Harman Kardon 2015-2017 WIRING DIAGRAM STEP 5 STEP 1 WHITE WHITE/BLACK GRAY GRAY/BLACK GREEN GREEN/BLACK PURPLE PURPLE/BLACK PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT. LF RCA INPUT RF RCA INPUT LR RCA INPUT CONNECT TO AFTERMARKET RADIO RR RCA INPUT MAIN HARNESS BLUE/WHITE - AMP.
PAGE 192
Subaru Legacy with 7 inch screen and Harman Kardon 2015-2017 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Illumination (+) Orange N/A Orange/White Orange/White Reverse Light (+) Purple/White Orange/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green VSS (vehicle speed sensor) (DATA) Pink Green/White Pink Pink Power Antenna (
PAGE 193
Subaru Legacy with 7 inch screen and Harman Kardon 2015-2017 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps.
PAGE 194
INSTALL GUIDE 2015-2017 Subaru Outback with 6.2 inch screen RETAINS STEERING WHEEL CONTROLS, AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-SU2 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-SUB2-DS ADDITIONAL RESOURCES ACC-uSU2 Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
PAGE 195
Subaru Outback with 6.2 inch screen 2015-2017 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
PAGE 196
Subaru Outback with 6.2 inch screen 2015-2017 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Cut the WHITE, GRAY, GREEN and PURPLE RCA tips. • Connect the wires from aftermarket radio main harness to the SU2 T-harness and match the wire functions. • Remove the factory radio. STEP 2 • Assemble the SU2 T-harness and connect it to the factory radio harness. STEP 3 Note: Connection required if the vehicle is equipped with Starlink telematics and a SOS button.
PAGE 197
Subaru Outback with 6.2 inch screen 2015-2017 WIRING DIAGRAM STEP 5 STEP 1 PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT. CUT AND REMOVE THE RCA JACKS CONNECT TO AFTERMARKET RADIO WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
PAGE 198
Subaru Outback with 6.
PAGE 199
Subaru Outback with 6.2 inch screen 2015-2017 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended.
PAGE 200
INSTALL GUIDE 2015-2017 Subaru Outback with 6.2 inch screen and Harman Kardon RETAINS STEERING WHEEL CONTROLS, AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-SU2 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-SUB2-DS ADDITIONAL RESOURCES ACC-uSU2 Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
PAGE 201
Subaru Outback with 6.2 inch screen and Harman Kardon 2015-2017 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
PAGE 202
Subaru Outback with 6.2 inch screen and Harman Kardon 2015-2017 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires from aftermarket radio main harness to the SU2 T-harness and match the wire functions. • Remove the factory radio. STEP 2 • Assemble the SU2 T-harness and connect it to the factory radio harness. STEP 3 Note: Connection required if the vehicle is equipped with Starlink telematics and a SOS button.
PAGE 203
Subaru Outback with 6.2 inch screen and Harman Kardon 2015-2017 WIRING DIAGRAM STEP 5 STEP 1 WHITE WHITE/BLACK GRAY GRAY/BLACK GREEN GREEN/BLACK PURPLE PURPLE/BLACK RCA CABLES LF RCA INPUT PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT. RF RCA INPUT LR RCA INPUT CONNECT TO AFTERMARKET RADIO RR RCA INPUT MAIN HARNESS BLUE/WHITE - AMP.
PAGE 204
Subaru Outback with 6.
PAGE 205
Subaru Outback with 6.2 inch screen and Harman Kardon 2015-2017 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps.
PAGE 206
INSTALL GUIDE 2015-2017 Subaru Outback with 7 inch screen RETAINS STEERING WHEEL CONTROLS, AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-SU2 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-SUB2-DS ADDITIONAL RESOURCES ACC-uSU2 Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
PAGE 207
Subaru Outback with 7 inch screen 2015-2017 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
PAGE 208
Subaru Outback with 7 inch screen 2015-2017 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Cut the WHITE, GRAY, GREEN and PURPLE RCA tips. • Connect the wires from aftermarket radio main harness to the SU2 T-harness and match the wire functions. • Remove the factory radio. STEP 2 • Assemble the SU2 T-harness and connect it to the factory radio harness. STEP 3 Note: Connection required if the vehicle is equipped with Starlink telematics and a SOS button.
PAGE 209
Subaru Outback with 7 inch screen 2015-2017 WIRING DIAGRAM STEP 5 STEP 1 PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT. CUT AND REMOVE THE RCA JACKS CONNECT TO AFTERMARKET RADIO WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
PAGE 210
Subaru Outback with 7 inch screen 2015-2017 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Illumination (+) Orange N/A Orange/White Orange/White Reverse Light (+) Purple/White Orange/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green VSS (vehicle speed sensor) (DATA) Pink Green/White Pink Pink Power Antenna (+) Blue Blue B
PAGE 211
Subaru Outback with 7 inch screen 2015-2017 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended.
PAGE 212
INSTALL GUIDE 2015-2017 Subaru Outback with 7 inch screen and Harman Kardon RETAINS STEERING WHEEL CONTROLS, AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-SU2 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-SUB2-DS ADDITIONAL RESOURCES ACC-uSU2 Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
PAGE 213
Subaru Outback with 7 inch screen and Harman Kardon 2015-2017 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
PAGE 214
Subaru Outback with 7 inch screen and Harman Kardon 2015-2017 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires from aftermarket radio main harness to the SU2 T-harness and match the wire functions. • Remove the factory radio. STEP 2 • Assemble the SU2 T-harness and connect it to the factory radio harness. STEP 3 Note: Connection required if the vehicle is equipped with Starlink telematics and a SOS button.
PAGE 215
Subaru Outback with 7 inch screen and Harman Kardon 2015-2017 WIRING DIAGRAM STEP 5 STEP 1 WHITE WHITE/BLACK GRAY GRAY/BLACK GREEN GREEN/BLACK PURPLE PURPLE/BLACK PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT. LF RCA INPUT RF RCA INPUT LR RCA INPUT CONNECT TO AFTERMARKET RADIO RR RCA INPUT MAIN HARNESS BLUE/WHITE - AMP.
PAGE 216
Subaru Outback with 7 inch screen and Harman Kardon 2015-2017 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Illumination (+) Orange N/A Orange/White Orange/White Reverse Light (+) Purple/White Orange/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green VSS (vehicle speed sensor) (DATA) Pink Green/White Pink Pink Power Antenna
PAGE 217
Subaru Outback with 7 inch screen and Harman Kardon 2015-2017 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps.
PAGE 218
INSTALL GUIDE 2016-2017 Subaru WRX STI with 6.2 inch screen RETAINS STEERING WHEEL CONTROLS, AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-SU2 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-SUB2-DS ADDITIONAL RESOURCES ACC-uSU2 Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
PAGE 219
Subaru WRX STI with 6.2 inch screen 2016-2017 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
PAGE 220
Subaru WRX STI with 6.2 inch screen 2016-2017 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Cut the WHITE, GRAY, GREEN and PURPLE RCA tips. • Connect the wires from aftermarket radio main harness to the SU2 T-harness and match the wire functions. • Remove the factory radio. STEP 2 • Assemble the SU2 T-harness and connect it to the factory radio harness. STEP 3 Note: Connection required if the vehicle is equipped with Starlink telematics and a SOS button.
PAGE 221
Subaru WRX STI with 6.2 inch screen 2016-2017 WIRING DIAGRAM STEP 5 STEP 1 PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT. CUT AND REMOVE THE RCA JACKS CONNECT TO AFTERMARKET RADIO WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
PAGE 222
Subaru WRX STI with 6.
PAGE 223
Subaru WRX STI with 6.2 inch screen 2016-2017 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended.
PAGE 224
INSTALL GUIDE 2016-2017 Subaru WRX STI with 6.2 inch screen and Harman Kardon RETAINS STEERING WHEEL CONTROLS, AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-SU2 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-SUB2-DS ADDITIONAL RESOURCES ACC-uSU2 Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
PAGE 225
Subaru WRX STI with 6.2 inch screen and Harman Kardon 2016-2017 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
PAGE 226
Subaru WRX STI with 6.2 inch screen and Harman Kardon 2016-2017 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires from aftermarket radio main harness to the SU2 T-harness and match the wire functions. • Remove the factory radio. STEP 2 • Assemble the SU2 T-harness and connect it to the factory radio harness. STEP 3 Note: Connection required if the vehicle is equipped with Starlink telematics and a SOS button.
PAGE 227
Subaru WRX STI with 6.2 inch screen and Harman Kardon 2016-2017 WIRING DIAGRAM STEP 5 STEP 1 WHITE WHITE/BLACK GRAY GRAY/BLACK GREEN GREEN/BLACK PURPLE PURPLE/BLACK RCA CABLES LF RCA INPUT PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT. RF RCA INPUT LR RCA INPUT CONNECT TO AFTERMARKET RADIO RR RCA INPUT MAIN HARNESS BLUE/WHITE - AMP.
PAGE 228
Subaru WRX STI with 6.
PAGE 229
Subaru WRX STI with 6.2 inch screen and Harman Kardon 2016-2017 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps.
PAGE 230
INSTALL GUIDE 2018-2020 Subaru WRX STI with 6.5 inch screen RETAINS STEERING WHEEL CONTROLS, AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-SU2 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-SUB2-DS ADDITIONAL RESOURCES ACC-uSU2 Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
PAGE 231
Subaru WRX STI with 6.5 inch screen 2018-2020 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
PAGE 232
Subaru WRX STI with 6.5 inch screen 2018-2020 INSTALLATION INSTRUCTIONS STEP 6 STEP 1 • Connect all the harnesses to the Maestro RR module then test your installation. • Unbox the aftermarket radio and locate its main harness. • Cut the WHITE, GRAY, GREEN and PURPLE RCA tips. • Connect the wires from aftermarket radio main harness to the SU2 T-harness and match the wire functions. • Remove the factory radio. STEP 2 • Assemble the SU2 T-harness and connect it to the factory radio harness.
PAGE 233
Subaru WRX STI with 6.5 inch screen 2018-2020 WIRING DIAGRAM STEP 5 STEP 1 PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT. CUT AND REMOVE THE RCA JACKS WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
PAGE 234
Subaru WRX STI with 6.
PAGE 235
Subaru WRX STI with 6.5 inch screen 2018-2020 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended.
PAGE 236
INSTALL GUIDE 2018-2020 Subaru WRX STI with 6.5 inch screen and Harman Kardon RETAINS STEERING WHEEL CONTROLS, AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-SU2 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-SUB2-DS ADDITIONAL RESOURCES ACC-uSU2 Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
PAGE 237
Subaru WRX STI with 6.5 inch screen and Harman Kardon 2018-2020 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
PAGE 238
Subaru WRX STI with 6.5 inch screen and Harman Kardon 2018-2020 INSTALLATION INSTRUCTIONS STEP 6 STEP 1 • Connect all the harnesses to the Maestro RR module then test your installation. • Unbox the aftermarket radio and locate its main harness. • Connect the wires from aftermarket radio main harness to the SU2 T-harness and match the wire functions. • Remove the factory radio. STEP 2 • Assemble the SU2 T-harness and connect it to the factory radio harness.
PAGE 239
Subaru WRX STI with 6.5 inch screen and Harman Kardon 2018-2020 WIRING DIAGRAM STEP 5 STEP 1 WHITE WHITE/BLACK GRAY GRAY/BLACK GREEN GREEN/BLACK PURPLE PURPLE/BLACK PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT. LF RCA INPUT RF RCA INPUT LR RCA INPUT CONNECT TO AFTERMARKET RADIO RR RCA INPUT MAIN HARNESS BLUE/WHITE - AMP.
PAGE 240
Subaru WRX STI with 6.
PAGE 241
Subaru WRX STI with 6.5 inch screen and Harman Kardon 2018-2020 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps.
PAGE 242
INSTALL GUIDE 2016-2017 Subaru WRX STI with 7 inch screen RETAINS STEERING WHEEL CONTROLS, AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-SU2 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-SUB2-DS ADDITIONAL RESOURCES ACC-uSU2 Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
PAGE 243
Subaru WRX STI with 7 inch screen 2016-2017 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
PAGE 244
Subaru WRX STI with 7 inch screen 2016-2017 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Cut the WHITE, GRAY, GREEN and PURPLE RCA tips. • Connect the wires from aftermarket radio main harness to the SU2 T-harness and match the wire functions. • Remove the factory radio. STEP 2 • Assemble the SU2 T-harness and connect it to the factory radio harness. STEP 3 Note: Connection required if the vehicle is equipped with Starlink telematics and a SOS button.
PAGE 245
Subaru WRX STI with 7 inch screen 2016-2017 WIRING DIAGRAM STEP 5 STEP 1 PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT. CUT AND REMOVE THE RCA JACKS CONNECT TO AFTERMARKET RADIO WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
PAGE 246
Subaru WRX STI with 7 inch screen 2016-2017 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Illumination (+) Orange N/A Orange/White Orange/White Reverse Light (+) Purple/White Orange/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green VSS (vehicle speed sensor) (DATA) Pink Green/White Pink Pink Power Antenna (+) Blue Blue B
PAGE 247
Subaru WRX STI with 7 inch screen 2016-2017 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended.
PAGE 248
INSTALL GUIDE 2018-2020 Subaru WRX STI with 7 inch screen RETAINS STEERING WHEEL CONTROLS, AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-SU2 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-SUB2-DS ADDITIONAL RESOURCES ACC-uSU2 Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
PAGE 249
Subaru WRX STI with 7 inch screen 2018-2020 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
PAGE 250
Subaru WRX STI with 7 inch screen 2018-2020 INSTALLATION INSTRUCTIONS STEP 6 STEP 1 • Connect all the harnesses to the Maestro RR module then test your installation. • Unbox the aftermarket radio and locate its main harness. • Cut the WHITE, GRAY, GREEN and PURPLE RCA tips. • Connect the wires from aftermarket radio main harness to the SU2 T-harness and match the wire functions. • Remove the factory radio. STEP 2 • Assemble the SU2 T-harness and connect it to the factory radio harness.
PAGE 251
Subaru WRX STI with 7 inch screen 2018-2020 WIRING DIAGRAM STEP 5 STEP 1 PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT. CUT AND REMOVE THE RCA JACKS WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
PAGE 252
Subaru WRX STI with 7 inch screen 2018-2020 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Illumination (+) Orange N/A Orange/White Orange/White Reverse Light (+) Purple/White Orange/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green VSS (vehicle speed sensor) (DATA) Pink Green/White Pink Pink Power Antenna (+) Blue Blue B
PAGE 253
Subaru WRX STI with 7 inch screen 2018-2020 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended.
PAGE 254
INSTALL GUIDE 2016-2017 Subaru WRX STI with 7 inch screen and Harman Kardon RETAINS STEERING WHEEL CONTROLS, AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-SU2 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-SUB2-DS ADDITIONAL RESOURCES ACC-uSU2 Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
PAGE 255
Subaru WRX STI with 7 inch screen and Harman Kardon 2016-2017 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
PAGE 256
Subaru WRX STI with 7 inch screen and Harman Kardon 2016-2017 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires from aftermarket radio main harness to the SU2 T-harness and match the wire functions. • Remove the factory radio. STEP 2 • Assemble the SU2 T-harness and connect it to the factory radio harness. STEP 3 Note: Connection required if the vehicle is equipped with Starlink telematics and a SOS button.
PAGE 257
Subaru WRX STI with 7 inch screen and Harman Kardon 2016-2017 WIRING DIAGRAM STEP 5 STEP 1 WHITE WHITE/BLACK GRAY GRAY/BLACK GREEN GREEN/BLACK PURPLE PURPLE/BLACK PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT. LF RCA INPUT RF RCA INPUT LR RCA INPUT CONNECT TO AFTERMARKET RADIO RR RCA INPUT MAIN HARNESS BLUE/WHITE - AMP.
PAGE 258
Subaru WRX STI with 7 inch screen and Harman Kardon 2016-2017 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Illumination (+) Orange N/A Orange/White Orange/White Reverse Light (+) Purple/White Orange/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green VSS (vehicle speed sensor) (DATA) Pink Green/White Pink Pink Power Antenna
PAGE 259
Subaru WRX STI with 7 inch screen and Harman Kardon 2016-2017 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps.
PAGE 260
INSTALL GUIDE 2018-2020 Subaru WRX STI with 7 inch screen and Harman Kardon RETAINS STEERING WHEEL CONTROLS, AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-SU2 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-SUB2-DS ADDITIONAL RESOURCES ACC-uSU2 Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
PAGE 261
Subaru WRX STI with 7 inch screen and Harman Kardon 2018-2020 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
PAGE 262
Subaru WRX STI with 7 inch screen and Harman Kardon 2018-2020 INSTALLATION INSTRUCTIONS STEP 6 STEP 1 • Connect all the harnesses to the Maestro RR module then test your installation. • Unbox the aftermarket radio and locate its main harness. • Connect the wires from aftermarket radio main harness to the SU2 T-harness and match the wire functions. • Remove the factory radio. STEP 2 • Assemble the SU2 T-harness and connect it to the factory radio harness.
PAGE 263
Subaru WRX STI with 7 inch screen and Harman Kardon 2018-2020 WIRING DIAGRAM STEP 5 STEP 1 WHITE WHITE/BLACK GRAY GRAY/BLACK GREEN GREEN/BLACK PURPLE PURPLE/BLACK PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT. LF RCA INPUT RF RCA INPUT LR RCA INPUT CONNECT TO AFTERMARKET RADIO RR RCA INPUT MAIN HARNESS BLUE/WHITE - AMP.
PAGE 264
Subaru WRX STI with 7 inch screen and Harman Kardon 2018-2020 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Illumination (+) Orange N/A Orange/White Orange/White Reverse Light (+) Purple/White Orange/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green VSS (vehicle speed sensor) (DATA) Pink Green/White Pink Pink Power Antenna
PAGE 265
Subaru WRX STI with 7 inch screen and Harman Kardon 2018-2020 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps.
PAGE 266
INSTALL GUIDE 2015 Subaru WRX STI with NAV RETAINS STEERING WHEEL CONTROLS, AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-SU2 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-SUB2-DS ADDITIONAL RESOURCES ACC-uSU2 Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
PAGE 267
Subaru WRX STI with NAV 2015 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Installation Instructions 3 Wiring Diagram 4 Radio Wire Reference Chart 5 Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct ﬁrmware for your vehicle and that you carefully review the install guide.
PAGE 268
Subaru WRX STI with NAV 2015 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Cut the WHITE, GRAY, GREEN and PURPLE RCA tips. • Connect the wires from aftermarket radio main harness to the SU2 T-harness and match the wire functions. • Remove the factory radio. STEP 2 • Assemble the SU2 T-harness and connect it to the factory radio harness. STEP 3 Note: Connection required if the vehicle is equipped with Starlink telematics and a SOS button.
PAGE 269
Subaru WRX STI with NAV 2015 WIRING DIAGRAM STEP 5 STEP 1 PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT. CUT AND REMOVE THE RCA JACKS CONNECT TO AFTERMARKET RADIO WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
PAGE 270
Subaru WRX STI with NAV 2015 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Illumination (+) Orange N/A Orange/White Orange/White Reverse Light (+) Purple/White Orange/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green VSS (vehicle speed sensor) (DATA) Pink Green/White Pink Pink Power Antenna (+) Blue Blue Blue N/A Autom
PAGE 271
Subaru WRX STI with NAV 2015 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended. Reset the RR.
PAGE 272
INSTALL GUIDE 2015 Subaru WRX STI with NAV and Amp RETAINS STEERING WHEEL CONTROLS, AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-SU2 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-SUB2-DS ADDITIONAL RESOURCES ACC-uSU2 Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
PAGE 273
Subaru WRX STI with NAV and Amp 2015 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
PAGE 274
Subaru WRX STI with NAV and Amp 2015 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires from aftermarket radio main harness to the SU2 T-harness and match the wire functions. • Remove the factory radio. STEP 2 • Assemble the SU2 T-harness and connect it to the factory radio harness. STEP 3 Note: Connection required if the vehicle is equipped with Starlink telematics and a SOS button.
PAGE 275
Subaru WRX STI with NAV and Amp 2015 WIRING DIAGRAM STEP 5 STEP 1 WHITE WHITE/BLACK GRAY GRAY/BLACK GREEN GREEN/BLACK PURPLE PURPLE/BLACK PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT. LF RCA INPUT RF RCA INPUT LR RCA INPUT CONNECT TO AFTERMARKET RADIO RR RCA INPUT MAIN HARNESS BLUE/WHITE - AMP.
PAGE 276
Subaru WRX STI with NAV and Amp 2015 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Illumination (+) Orange N/A Orange/White Orange/White Reverse Light (+) Purple/White Orange/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green VSS (vehicle speed sensor) (DATA) Pink Green/White Pink Pink Power Antenna (+) Blue Blue Blue N/
PAGE 277
Subaru WRX STI with NAV and Amp 2015 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended. Reset the RR.
PAGE 278
INSTALL GUIDE 2016-2017 Subaru WRX with 6.2 inch screen RETAINS STEERING WHEEL CONTROLS, AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-SU2 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-SUB2-DS ADDITIONAL RESOURCES ACC-uSU2 Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
PAGE 279
Subaru WRX with 6.2 inch screen 2016-2017 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
PAGE 280
Subaru WRX with 6.2 inch screen 2016-2017 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Cut the WHITE, GRAY, GREEN and PURPLE RCA tips. • Connect the wires from aftermarket radio main harness to the SU2 T-harness and match the wire functions. • Remove the factory radio. STEP 2 • Assemble the SU2 T-harness and connect it to the factory radio harness. STEP 3 Note: Connection required if the vehicle is equipped with Starlink telematics and a SOS button.
PAGE 281
Subaru WRX with 6.2 inch screen 2016-2017 WIRING DIAGRAM STEP 5 STEP 1 PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT. CUT AND REMOVE THE RCA JACKS CONNECT TO AFTERMARKET RADIO WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
PAGE 282
Subaru WRX with 6.
PAGE 283
Subaru WRX with 6.2 inch screen 2016-2017 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended. Reset the RR.
PAGE 284
INSTALL GUIDE 2016-2017 Subaru WRX with 6.2 inch screen and Harman Kardon RETAINS STEERING WHEEL CONTROLS, AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-SU2 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-SUB2-DS ADDITIONAL RESOURCES ACC-uSU2 Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
PAGE 285
Subaru WRX with 6.2 inch screen and Harman Kardon 2016-2017 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
PAGE 286
Subaru WRX with 6.2 inch screen and Harman Kardon 2016-2017 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires from aftermarket radio main harness to the SU2 T-harness and match the wire functions. • Remove the factory radio. STEP 2 • Assemble the SU2 T-harness and connect it to the factory radio harness. STEP 3 Note: Connection required if the vehicle is equipped with Starlink telematics and a SOS button.
PAGE 287
Subaru WRX with 6.2 inch screen and Harman Kardon 2016-2017 WIRING DIAGRAM STEP 5 STEP 1 WHITE WHITE/BLACK GRAY GRAY/BLACK GREEN GREEN/BLACK PURPLE PURPLE/BLACK RCA CABLES LF RCA INPUT PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT. RF RCA INPUT LR RCA INPUT CONNECT TO AFTERMARKET RADIO RR RCA INPUT MAIN HARNESS BLUE/WHITE - AMP.
PAGE 288
Subaru WRX with 6.
PAGE 289
Subaru WRX with 6.2 inch screen and Harman Kardon 2016-2017 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps.
PAGE 290
INSTALL GUIDE 2018-2020 Subaru WRX with 6.5 inch screen RETAINS STEERING WHEEL CONTROLS, AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-SU2 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-SUB2-DS ADDITIONAL RESOURCES ACC-uSU2 Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
PAGE 291
Subaru WRX with 6.5 inch screen 2018-2020 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
PAGE 292
Subaru WRX with 6.5 inch screen 2018-2020 INSTALLATION INSTRUCTIONS STEP 6 STEP 1 • Connect all the harnesses to the Maestro RR module then test your installation. • Unbox the aftermarket radio and locate its main harness. • Cut the WHITE, GRAY, GREEN and PURPLE RCA tips. • Connect the wires from aftermarket radio main harness to the SU2 T-harness and match the wire functions. • Remove the factory radio. STEP 2 • Assemble the SU2 T-harness and connect it to the factory radio harness.
PAGE 293
Subaru WRX with 6.5 inch screen 2018-2020 WIRING DIAGRAM STEP 5 STEP 1 PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT. CUT AND REMOVE THE RCA JACKS WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
PAGE 294
Subaru WRX with 6.
PAGE 295
Subaru WRX with 6.5 inch screen 2018-2020 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended. Reset the RR.
PAGE 296
INSTALL GUIDE 2018-2020 Subaru WRX with 6.5 inch screen and Harman Kardon RETAINS STEERING WHEEL CONTROLS, AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-SU2 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-SUB2-DS ADDITIONAL RESOURCES ACC-uSU2 Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
PAGE 297
Subaru WRX with 6.5 inch screen and Harman Kardon 2018-2020 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
PAGE 298
Subaru WRX with 6.5 inch screen and Harman Kardon 2018-2020 INSTALLATION INSTRUCTIONS STEP 6 STEP 1 • Connect all the harnesses to the Maestro RR module then test your installation. • Unbox the aftermarket radio and locate its main harness. • Connect the wires from aftermarket radio main harness to the SU2 T-harness and match the wire functions. • Remove the factory radio. STEP 2 • Assemble the SU2 T-harness and connect it to the factory radio harness.
PAGE 299
Subaru WRX with 6.5 inch screen and Harman Kardon 2018-2020 WIRING DIAGRAM STEP 5 STEP 1 WHITE WHITE/BLACK GRAY GRAY/BLACK GREEN GREEN/BLACK PURPLE PURPLE/BLACK PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT. LF RCA INPUT RF RCA INPUT LR RCA INPUT CONNECT TO AFTERMARKET RADIO RR RCA INPUT MAIN HARNESS BLUE/WHITE - AMP.
PAGE 300
Subaru WRX with 6.
PAGE 301
Subaru WRX with 6.5 inch screen and Harman Kardon 2018-2020 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps.
PAGE 302
INSTALL GUIDE 2016-2017 Subaru WRX with 7 inch screen RETAINS STEERING WHEEL CONTROLS, AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-SU2 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-SUB2-DS ADDITIONAL RESOURCES ACC-uSU2 Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
PAGE 303
Subaru WRX with 7 inch screen 2016-2017 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
PAGE 304
Subaru WRX with 7 inch screen 2016-2017 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Cut the WHITE, GRAY, GREEN and PURPLE RCA tips. • Connect the wires from aftermarket radio main harness to the SU2 T-harness and match the wire functions. • Remove the factory radio. STEP 2 • Assemble the SU2 T-harness and connect it to the factory radio harness. STEP 3 Note: Connection required if the vehicle is equipped with Starlink telematics and a SOS button.
PAGE 305
Subaru WRX with 7 inch screen 2016-2017 WIRING DIAGRAM STEP 5 STEP 1 PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT. CUT AND REMOVE THE RCA JACKS CONNECT TO AFTERMARKET RADIO WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
PAGE 306
Subaru WRX with 7 inch screen 2016-2017 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Illumination (+) Orange N/A Orange/White Orange/White Reverse Light (+) Purple/White Orange/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green VSS (vehicle speed sensor) (DATA) Pink Green/White Pink Pink Power Antenna (+) Blue Blue Blue
PAGE 307
Subaru WRX with 7 inch screen 2016-2017 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended. Reset the RR.
PAGE 308
INSTALL GUIDE 2018-2020 Subaru WRX with 7 inch screen RETAINS STEERING WHEEL CONTROLS, AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-SU2 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-SUB2-DS ADDITIONAL RESOURCES ACC-uSU2 Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
PAGE 309
Subaru WRX with 7 inch screen 2018-2020 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
PAGE 310
Subaru WRX with 7 inch screen 2018-2020 INSTALLATION INSTRUCTIONS STEP 6 STEP 1 • Connect all the harnesses to the Maestro RR module then test your installation. • Unbox the aftermarket radio and locate its main harness. • Cut the WHITE, GRAY, GREEN and PURPLE RCA tips. • Connect the wires from aftermarket radio main harness to the SU2 T-harness and match the wire functions. • Remove the factory radio. STEP 2 • Assemble the SU2 T-harness and connect it to the factory radio harness.
PAGE 311
Subaru WRX with 7 inch screen 2018-2020 WIRING DIAGRAM STEP 5 STEP 1 PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT. CUT AND REMOVE THE RCA JACKS WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
PAGE 312
Subaru WRX with 7 inch screen 2018-2020 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Illumination (+) Orange N/A Orange/White Orange/White Reverse Light (+) Purple/White Orange/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green VSS (vehicle speed sensor) (DATA) Pink Green/White Pink Pink Power Antenna (+) Blue Blue Blue
PAGE 313
Subaru WRX with 7 inch screen 2018-2020 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended. Reset the RR.
PAGE 314
INSTALL GUIDE 2016-2017 Subaru WRX with 7 inch screen and Harman Kardon RETAINS STEERING WHEEL CONTROLS, AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-SU2 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-SUB2-DS ADDITIONAL RESOURCES ACC-uSU2 Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
PAGE 315
Subaru WRX with 7 inch screen and Harman Kardon 2016-2017 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
PAGE 316
Subaru WRX with 7 inch screen and Harman Kardon 2016-2017 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires from aftermarket radio main harness to the SU2 T-harness and match the wire functions. • Remove the factory radio. STEP 2 • Assemble the SU2 T-harness and connect it to the factory radio harness. STEP 3 Note: Connection required if the vehicle is equipped with Starlink telematics and a SOS button.
PAGE 317
Subaru WRX with 7 inch screen and Harman Kardon 2016-2017 WIRING DIAGRAM STEP 5 STEP 1 WHITE WHITE/BLACK GRAY GRAY/BLACK GREEN GREEN/BLACK PURPLE PURPLE/BLACK PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT. LF RCA INPUT RF RCA INPUT LR RCA INPUT CONNECT TO AFTERMARKET RADIO RR RCA INPUT MAIN HARNESS BLUE/WHITE - AMP.
PAGE 318
Subaru WRX with 7 inch screen and Harman Kardon 2016-2017 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Illumination (+) Orange N/A Orange/White Orange/White Reverse Light (+) Purple/White Orange/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green VSS (vehicle speed sensor) (DATA) Pink Green/White Pink Pink Power Antenna (+)
PAGE 319
Subaru WRX with 7 inch screen and Harman Kardon 2016-2017 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps.
PAGE 320
INSTALL GUIDE 2018-2020 Subaru WRX with 7 inch screen and Harman Kardon RETAINS STEERING WHEEL CONTROLS, AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-SU2 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-SUB2-DS ADDITIONAL RESOURCES ACC-uSU2 Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
PAGE 321
Subaru WRX with 7 inch screen and Harman Kardon 2018-2020 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
PAGE 322
Subaru WRX with 7 inch screen and Harman Kardon 2018-2020 INSTALLATION INSTRUCTIONS STEP 6 STEP 1 • Connect all the harnesses to the Maestro RR module then test your installation. • Unbox the aftermarket radio and locate its main harness. • Connect the wires from aftermarket radio main harness to the SU2 T-harness and match the wire functions. • Remove the factory radio. STEP 2 • Assemble the SU2 T-harness and connect it to the factory radio harness. • Locate the 28 pin connector on the SU2 T-harness.
PAGE 323
Subaru WRX with 7 inch screen and Harman Kardon 2018-2020 WIRING DIAGRAM STEP 5 STEP 1 WHITE WHITE/BLACK GRAY GRAY/BLACK GREEN GREEN/BLACK PURPLE PURPLE/BLACK PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT. LF RCA INPUT RF RCA INPUT LR RCA INPUT CONNECT TO AFTERMARKET RADIO RR RCA INPUT MAIN HARNESS BLUE/WHITE - AMP.
PAGE 324
Subaru WRX with 7 inch screen and Harman Kardon 2018-2020 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Illumination (+) Orange N/A Orange/White Orange/White Reverse Light (+) Purple/White Orange/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green VSS (vehicle speed sensor) (DATA) Pink Green/White Pink Pink Power Antenna (+)
PAGE 325
Subaru WRX with 7 inch screen and Harman Kardon 2018-2020 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps.
PAGE 326
INSTALL GUIDE 2015 Subaru WRX with NAV RETAINS STEERING WHEEL CONTROLS, AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-SU2 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-SUB2-DS ADDITIONAL RESOURCES ACC-uSU2 Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
PAGE 327
Subaru WRX with NAV 2015 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Installation Instructions 3 Wiring Diagram 4 Radio Wire Reference Chart 5 Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct ﬁrmware for your vehicle and that you carefully review the install guide.
PAGE 328
Subaru WRX with NAV 2015 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Cut the WHITE, GRAY, GREEN and PURPLE RCA tips. • Connect the wires from aftermarket radio main harness to the SU2 T-harness and match the wire functions. • Remove the factory radio. STEP 2 • Assemble the SU2 T-harness and connect it to the factory radio harness. STEP 3 Note: Connection required if the vehicle is equipped with Starlink telematics and a SOS button.
PAGE 329
Subaru WRX with NAV 2015 WIRING DIAGRAM STEP 5 STEP 1 PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT. CUT AND REMOVE THE RCA JACKS CONNECT TO AFTERMARKET RADIO WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
PAGE 330
Subaru WRX with NAV 2015 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Illumination (+) Orange N/A Orange/White Orange/White Reverse Light (+) Purple/White Orange/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green VSS (vehicle speed sensor) (DATA) Pink Green/White Pink Pink Power Antenna (+) Blue Blue Blue N/A Automotiv
PAGE 331
Subaru WRX with NAV 2015 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended. Reset the RR.
PAGE 332
INSTALL GUIDE 2015 Subaru WRX with NAV and Amp RETAINS STEERING WHEEL CONTROLS, AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-SU2 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-SUB2-DS ADDITIONAL RESOURCES ACC-uSU2 Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
PAGE 333
Subaru WRX with NAV and Amp 2015 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
PAGE 334
Subaru WRX with NAV and Amp 2015 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires from aftermarket radio main harness to the SU2 T-harness and match the wire functions. • Remove the factory radio. STEP 2 • Assemble the SU2 T-harness and connect it to the factory radio harness. STEP 3 Note: Connection required if the vehicle is equipped with Starlink telematics and a SOS button.
PAGE 335
Subaru WRX with NAV and Amp 2015 WIRING DIAGRAM STEP 5 STEP 1 WHITE WHITE/BLACK GRAY GRAY/BLACK GREEN GREEN/BLACK PURPLE PURPLE/BLACK PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT. LF RCA INPUT RF RCA INPUT LR RCA INPUT CONNECT TO AFTERMARKET RADIO RR RCA INPUT MAIN HARNESS BLUE/WHITE - AMP.
PAGE 336
Subaru WRX with NAV and Amp 2015 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Illumination (+) Orange N/A Orange/White Orange/White Reverse Light (+) Purple/White Orange/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green VSS (vehicle speed sensor) (DATA) Pink Green/White Pink Pink Power Antenna (+) Blue Blue Blue N/A A
PAGE 337
Subaru WRX with NAV and Amp 2015 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended. Reset the RR.
PAGE 338
INSTALL GUIDE 2015-2017 Subaru XV Crosstrek with 6.2 inch screen RETAINS STEERING WHEEL CONTROLS, AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-SU2 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-SUB2-DS ADDITIONAL RESOURCES ACC-uSU2 Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
PAGE 339
Subaru XV Crosstrek with 6.2 inch screen 2015-2017 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
PAGE 340
Subaru XV Crosstrek with 6.2 inch screen 2015-2017 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Cut the WHITE, GRAY, GREEN and PURPLE RCA tips. • Connect the wires from aftermarket radio main harness to the SU2 T-harness and match the wire functions. • Remove the factory radio. STEP 2 • Assemble the SU2 T-harness and connect it to the factory radio harness.
PAGE 341
Subaru XV Crosstrek with 6.2 inch screen 2015-2017 WIRING DIAGRAM STEP 5 STEP 1 PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT. CUT AND REMOVE THE RCA JACKS CONNECT TO AFTERMARKET RADIO WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
PAGE 342
Subaru XV Crosstrek with 6.
PAGE 343
Subaru XV Crosstrek with 6.2 inch screen 2015-2017 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended.
PAGE 344
INSTALL GUIDE 2015-2017 Subaru XV Crosstrek with 6.2 inch screen and Harman Kardon RETAINS STEERING WHEEL CONTROLS, AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-SU2 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-SUB2-DS ADDITIONAL RESOURCES ACC-uSU2 Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
PAGE 345
Subaru XV Crosstrek with 6.2 inch screen and Harman Kardon 2015-2017 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
PAGE 346
Subaru XV Crosstrek with 6.2 inch screen and Harman Kardon 2015-2017 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires from aftermarket radio main harness to the SU2 T-harness and match the wire functions. • Remove the factory radio. STEP 2 • Assemble the SU2 T-harness and connect it to the factory radio harness. STEP 3 Note: Connection required if the vehicle is equipped with Starlink telematics and a SOS button.
PAGE 347
Subaru XV Crosstrek with 6.2 inch screen and Harman Kardon 2015-2017 WIRING DIAGRAM STEP 5 STEP 1 WHITE WHITE/BLACK GRAY GRAY/BLACK GREEN GREEN/BLACK PURPLE PURPLE/BLACK RCA CABLES LF RCA INPUT PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT. RF RCA INPUT LR RCA INPUT CONNECT TO AFTERMARKET RADIO RR RCA INPUT MAIN HARNESS BLUE/WHITE - AMP.
PAGE 348
Subaru XV Crosstrek with 6.
PAGE 349
Subaru XV Crosstrek with 6.2 inch screen and Harman Kardon 2015-2017 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps.
PAGE 350
INSTALL GUIDE 2015-2017 Subaru XV Crosstrek with 7 inch screen RETAINS STEERING WHEEL CONTROLS, AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-SU2 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-SUB2-DS ADDITIONAL RESOURCES ACC-uSU2 Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
PAGE 351
Subaru XV Crosstrek with 7 inch screen 2015-2017 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
PAGE 352
Subaru XV Crosstrek with 7 inch screen 2015-2017 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Cut the WHITE, GRAY, GREEN and PURPLE RCA tips. • Connect the wires from aftermarket radio main harness to the SU2 T-harness and match the wire functions. • Remove the factory radio. STEP 2 • Assemble the SU2 T-harness and connect it to the factory radio harness. STEP 3 Note: Connection required if the vehicle is equipped with Starlink telematics and a SOS button.
PAGE 353
Subaru XV Crosstrek with 7 inch screen 2015-2017 WIRING DIAGRAM STEP 5 STEP 1 PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT. CUT AND REMOVE THE RCA JACKS CONNECT TO AFTERMARKET RADIO WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
PAGE 354
Subaru XV Crosstrek with 7 inch screen 2015-2017 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Illumination (+) Orange N/A Orange/White Orange/White Reverse Light (+) Purple/White Orange/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green VSS (vehicle speed sensor) (DATA) Pink Green/White Pink Pink Power Antenna (+) Blue Bl
PAGE 355
Subaru XV Crosstrek with 7 inch screen 2015-2017 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended.
PAGE 356
INSTALL GUIDE 2015-2017 Subaru XV Crosstrek with 7 inch screen and Harman Kardon RETAINS STEERING WHEEL CONTROLS, AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-SU2 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-SUB2-DS ADDITIONAL RESOURCES ACC-uSU2 Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
PAGE 357
Subaru XV Crosstrek with 7 inch screen and Harman Kardon 2015-2017 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
PAGE 358
Subaru XV Crosstrek with 7 inch screen and Harman Kardon 2015-2017 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires from aftermarket radio main harness to the SU2 T-harness and match the wire functions. • Remove the factory radio. STEP 2 • Assemble the SU2 T-harness and connect it to the factory radio harness. STEP 3 Note: Connection required if the vehicle is equipped with Starlink telematics and a SOS button.
PAGE 359
Subaru XV Crosstrek with 7 inch screen and Harman Kardon 2015-2017 WIRING DIAGRAM STEP 5 STEP 1 WHITE WHITE/BLACK GRAY GRAY/BLACK GREEN GREEN/BLACK PURPLE PURPLE/BLACK PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT. LF RCA INPUT RF RCA INPUT LR RCA INPUT CONNECT TO AFTERMARKET RADIO RR RCA INPUT MAIN HARNESS BLUE/WHITE - AMP.
PAGE 360
Subaru XV Crosstrek with 7 inch screen and Harman Kardon 2015-2017 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Illumination (+) Orange N/A Orange/White Orange/White Reverse Light (+) Purple/White Orange/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green VSS (vehicle speed sensor) (DATA) Pink Green/White Pink Pink Power Ante
PAGE 361
Subaru XV Crosstrek with 7 inch screen and Harman Kardon 2015-2017 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps.
PAGE 362
INSTALL GUIDE 2013-2014 Subaru XV Crosstrek with Harman Kardon and OEM camera on radio RETAINS STEERING WHEEL CONTROLS, AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-SU2 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-SUB2-DS ADDITIONAL RESOURCES ACC-uSU2 Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
PAGE 363
Subaru XV Crosstrek with Harman Kardon and OEM camera on radio 2013-2014 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
PAGE 364
Subaru XV Crosstrek with Harman Kardon and OEM camera on radio 2013-2014 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires from aftermarket radio main harness to the SU2 T-harness and match the wire functions. • Remove the factory radio. STEP 2 • Assemble the SU2 T-harness and connect it to the factory radio harness. STEP 3 • Plug the OBDII connector into the OBDII of the vehicle, under driver dash.
PAGE 365
Subaru XV Crosstrek with Harman Kardon and OEM camera on radio 2013-2014 WIRING DIAGRAM STEP 4 STEP 1 WHITE WHITE/BLACK GRAY GRAY/BLACK GREEN GREEN/BLACK PURPLE PURPLE/BLACK PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT. LF RCA INPUT RF RCA INPUT LR RCA INPUT CONNECT TO AFTERMARKET RADIO RR RCA INPUT MAIN HARNESS BLUE/WHITE - AMP.
PAGE 366
Subaru XV Crosstrek with Harman Kardon and OEM camera on radio 2013-2014 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Illumination (+) Orange N/A Orange/White Orange/White Reverse Light (+) Purple/White Orange/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green VSS (vehicle speed sensor) (DATA) Pink Green/White Pink Pink Powe
PAGE 367
Subaru XV Crosstrek with Harman Kardon and OEM camera on radio 2013-2014 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps.
PAGE 368
INSTALL GUIDE 2013-2014 Subaru XV Crosstrek with NAV and Harman Kardon and OEM camera on secondary display RETAINS STEERING WHEEL CONTROLS, AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-SU2 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-SUB2-DS ADDITIONAL RESOURCES ACC-uSU2 Maestro RR2 Programmable Outputs Guide NOTICE: Automotive D
PAGE 369
Subaru XV Crosstrek with NAV and Harman Kardon and OEM camera on secondary display WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
PAGE 370
Subaru XV Crosstrek with NAV and Harman Kardon and OEM camera on secondary display INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires from aftermarket radio main harness to the SU2 T-harness and match the wire functions. • Remove the factory radio. STEP 2 • Assemble the SU2 T-harness and connect it to the factory radio harness. STEP 3 • Plug the OBDII connector into the OBDII of the vehicle, under driver dash.
PAGE 371
Subaru XV Crosstrek with NAV and Harman Kardon and OEM camera on secondary display WIRING DIAGRAM STEP 4 STEP 1 WHITE WHITE/BLACK GRAY GRAY/BLACK GREEN GREEN/BLACK PURPLE PURPLE/BLACK PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT. LF RCA INPUT RF RCA INPUT LR RCA INPUT CONNECT TO AFTERMARKET RADIO RR RCA INPUT MAIN HARNESS BLUE/WHITE - AMP.
PAGE 372
Subaru XV Crosstrek with NAV and Harman Kardon and OEM camera on secondary display RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Illumination (+) Orange N/A Orange/White Orange/White Reverse Light (+) Purple/White Orange/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green VSS (vehicle speed sensor) (DATA) Pink Green/White Pink
PAGE 373
Subaru XV Crosstrek with NAV and Harman Kardon and OEM camera on secondary display TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps.
PAGE 374
INSTALL GUIDE 2013-2014 Subaru XV Crosstrek with NAV and OEM camera on secondary display RETAINS STEERING WHEEL CONTROLS, AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-SU2 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-SUB2-DS ADDITIONAL RESOURCES ACC-uSU2 Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
PAGE 375
Subaru XV Crosstrek with NAV and OEM camera on secondary display 2013-2014 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
PAGE 376
Subaru XV Crosstrek with NAV and OEM camera on secondary display 2013-2014 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Cut the WHITE, GRAY, GREEN and PURPLE RCA tips. • Connect the wires from aftermarket radio main harness to the SU2 T-harness and match the wire functions. • Remove the factory radio. STEP 2 • Assemble the SU2 T-harness and connect it to the factory radio harness.
PAGE 377
Subaru XV Crosstrek with NAV and OEM camera on secondary display 2013-2014 WIRING DIAGRAM STEP 4 STEP 1 PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT. CUT AND REMOVE THE RCA JACKS CONNECT TO AFTERMARKET RADIO WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
PAGE 378
Subaru XV Crosstrek with NAV and OEM camera on secondary display 2013-2014 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Illumination (+) Orange N/A Orange/White Orange/White Reverse Light (+) Purple/White Orange/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green VSS (vehicle speed sensor) (DATA) Pink Green/White Pink Pink Po
PAGE 379
Subaru XV Crosstrek with NAV and OEM camera on secondary display 2013-2014 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps.
PAGE 380
INSTALL GUIDE 2013-2014 Subaru XV Crosstrek with OEM camera on radio RETAINS STEERING WHEEL CONTROLS, AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-SU2 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-SUB2-DS ADDITIONAL RESOURCES ACC-uSU2 Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
PAGE 381
Subaru XV Crosstrek with OEM camera on radio 2013-2014 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
PAGE 382
Subaru XV Crosstrek with OEM camera on radio 2013-2014 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Cut the WHITE, GRAY, GREEN and PURPLE RCA tips. • Connect the wires from aftermarket radio main harness to the SU2 T-harness and match the wire functions. • Remove the factory radio. STEP 2 • Assemble the SU2 T-harness and connect it to the factory radio harness. STEP 3 • Plug the OBDII connector into the OBDII of the vehicle, under driver dash.
PAGE 383
Subaru XV Crosstrek with OEM camera on radio 2013-2014 WIRING DIAGRAM STEP 4 STEP 1 PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT. CUT AND REMOVE THE RCA JACKS CONNECT TO AFTERMARKET RADIO WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
PAGE 384
Subaru XV Crosstrek with OEM camera on radio 2013-2014 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Illumination (+) Orange N/A Orange/White Orange/White Reverse Light (+) Purple/White Orange/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green VSS (vehicle speed sensor) (DATA) Pink Green/White Pink Pink Power Antenna (+) Bl
PAGE 385
Subaru XV Crosstrek with OEM camera on radio 2013-2014 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended.
PAGE 386
INSTALL GUIDE 2017-2019 Toyota 86 Base RETAINS STEERING WHEEL CONTROLS, AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-SU2 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-SUB2-DS ADDITIONAL RESOURCES ACC-uSU2 Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
PAGE 387
Toyota 86 Base 2017-2019 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Installation Instructions 3 Wiring Diagram 4 Radio Wire Reference Chart 5 Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct ﬁrmware for your vehicle and that you carefully review the install guide.
PAGE 388
Toyota 86 Base 2017-2019 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Cut the WHITE, GRAY, GREEN and PURPLE RCA tips. • Connect the wires from aftermarket radio main harness to the SU2 T-harness and match the wire functions. • Remove the factory radio. STEP 2 • Assemble the SU2 T-harness and connect it to the factory radio harness. STEP 3 Note: Connection required if the vehicle is equipped with Starlink telematics and a SOS button.
PAGE 389
Toyota 86 Base 2017-2019 WIRING DIAGRAM STEP 5 STEP 1 PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT. CUT AND REMOVE THE RCA JACKS CONNECT TO AFTERMARKET RADIO WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
PAGE 390
Toyota 86 Base 2017-2019 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Illumination (+) Orange N/A Orange/White Orange/White Reverse Light (+) Purple/White Orange/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green VSS (vehicle speed sensor) (DATA) Pink Green/White Pink Pink Power Antenna (+) Blue Blue Blue N/A Automotiv
PAGE 391
Toyota 86 Base 2017-2019 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended. Reset the RR.
PAGE 392
INSTALL GUIDE 2017-2019 Toyota 86 With Amp RETAINS STEERING WHEEL CONTROLS, AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-SU2 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-SUB2-DS ADDITIONAL RESOURCES ACC-uSU2 Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
PAGE 393
Toyota 86 With Amp 2017-2019 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Installation Instructions 3 Wiring Diagram 4 Radio Wire Reference Chart 5 Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct ﬁrmware for your vehicle and that you carefully review the install guide.
PAGE 394
Toyota 86 With Amp 2017-2019 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Cut the WHITE, GRAY, GREEN and PURPLE RCA tips. • Connect the wires from aftermarket radio main harness to the SU2 T-harness and match the wire functions. • Remove the factory radio. STEP 2 • Assemble the SU2 T-harness and connect it to the factory radio harness.
PAGE 395
Toyota 86 With Amp 2017-2019 WIRING DIAGRAM STEP 5 STEP 1 PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT. CUT AND REMOVE THE RCA JACKS WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
PAGE 396
Toyota 86 With Amp 2017-2019 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Illumination (+) Orange N/A Orange/White Orange/White Reverse Light (+) Purple/White Orange/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green VSS (vehicle speed sensor) (DATA) Pink Green/White Pink Pink Power Antenna (+) Blue Blue Blue N/A Autom
PAGE 397
Toyota 86 With Amp 2017-2019 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended. Reset the RR.
PAGE 398
INSTALL GUIDE 2017-2019 Toyota 86 With NAV RETAINS STEERING WHEEL CONTROLS, AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-SU2 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-SUB2-DS ADDITIONAL RESOURCES ACC-uSU2 Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
PAGE 399
Toyota 86 With NAV 2017-2019 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Installation Instructions 3 Wiring Diagram 4 Radio Wire Reference Chart 5 Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct ﬁrmware for your vehicle and that you carefully review the install guide.
PAGE 400
Toyota 86 With NAV 2017-2019 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Cut the WHITE, GRAY, GREEN and PURPLE RCA tips. • Connect the wires from aftermarket radio main harness to the SU2 T-harness and match the wire functions. • Remove the factory radio. STEP 2 • Assemble the SU2 T-harness and connect it to the factory radio harness. STEP 3 Note: Connection required if the vehicle is equipped with Starlink telematics and a SOS button.
PAGE 401
Toyota 86 With NAV 2017-2019 WIRING DIAGRAM STEP 5 STEP 1 PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT. CUT AND REMOVE THE RCA JACKS CONNECT TO AFTERMARKET RADIO WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
PAGE 402
Toyota 86 With NAV 2017-2019 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Illumination (+) Orange N/A Orange/White Orange/White Reverse Light (+) Purple/White Orange/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green VSS (vehicle speed sensor) (DATA) Pink Green/White Pink Pink Power Antenna (+) Blue Blue Blue N/A Autom
PAGE 403
Toyota 86 With NAV 2017-2019 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended. Reset the RR.
PAGE 404
INSTALL GUIDE 2017-2019 Toyota 86 With NAV With Amp RETAINS STEERING WHEEL CONTROLS, AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-SU2 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-SUB2-DS ADDITIONAL RESOURCES ACC-uSU2 Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
PAGE 405
Toyota 86 With NAV With Amp 2017-2019 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
PAGE 406
Toyota 86 With NAV With Amp 2017-2019 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Cut the WHITE, GRAY, GREEN and PURPLE RCA tips. • Connect the wires from aftermarket radio main harness to the SU2 T-harness and match the wire functions. • Remove the factory radio. STEP 2 • Assemble the SU2 T-harness and connect it to the factory radio harness.
PAGE 407
Toyota 86 With NAV With Amp 2017-2019 WIRING DIAGRAM STEP 5 STEP 1 PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT. CUT AND REMOVE THE RCA JACKS WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
PAGE 408
Toyota 86 With NAV With Amp 2017-2019 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Illumination (+) Orange N/A Orange/White Orange/White Reverse Light (+) Purple/White Orange/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green VSS (vehicle speed sensor) (DATA) Pink Green/White Pink Pink Power Antenna (+) Blue Blue Blue N
PAGE 409
Toyota 86 With NAV With Amp 2017-2019 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended. Reset the RR.