SELECT VEHICLE PRINT PAGES NEEDED HOW TO USE THIS INSTALL GUIDE 1 Open the Bookmarks menu and find your vehicle OR scroll down until you find the install guide for your vehicle. 2 Print only the pages for your vehicle using the advanced options in the Print menu. 3 Install your Maestro RR according to the guide for your vehicle. WARNING Pressing the printer icon or “quick printing” this document will print all of the guides in this compilation. NOTICE: Automotive Data Solutions Inc.
INSTALL GUIDE 2016 Scion iM RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro TO1 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY01-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Scion iM 2016 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Installation Instructions 3 Wiring Diagram 4 Radio Wire Reference Chart 5 Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware for your vehicle and that you carefully review the install guide.
Scion iM 2016 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on the next page from aftermarket radio main harness to the TO1 T-harness and match the wire functions. • Remove the factory radio. STEP 2 • If the vehicle is equipped with an OEM backup camera, connect the TO1 T-harness to the backup camera harness (see wire chart for details). STEP 3 • Identify if your vehicle has a 20 or 28 pin secondary connector.
Scion iM 2016 WIRING DIAGRAM without an Amplifier STEP 5 STEP 1 WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Scion iM 2016 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A N/A VSS (vehicle
Scion iM 2016 VEHICLE WIRE REFERENCE CHART Wire Description Connector Name Connector Color Connector Type Position Wire Color Polarity Wire Location Camera Power ~ ~ 24 pin 11 Red (+) Reverse camera harness Ground ~ ~ 24 pin 23 Shield (-) Reverse camera harness Video + ~ ~ 24 pin 12 Black (+) Reverse camera harness Video - ~ ~ 24 pin 24 White (-) Reverse camera harness REVERSE CAMERA CONNECTORS (WIRE SIDE) 12 11 10 9 8 7 6 5 4 3 2 1 24 23 22 21 20 19 18 17
Scion iM 2016 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended. Reset the RR.
Owner's Guide TO1 & Alpine radio RETAINS STEERING WHEEL CONTROLS, FACTORY SETTINGS AND MORE! PRODUCTS REQUIRED OPTIONAL ACCESSORIES PROGRAMMED FIRMWARE •iDatalink Maestro RR Radio Replacement Interface •TO1 Installation Harness ADS-RR(SR)-TOY01-DS NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.
TABLE OF CONTENTS WELCOME Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. This guide is a great addition to both the vehicle owner’s guide and the aftermarket radio owner’s guide. We recommand having both these documents handy as they cover all the functionality that the Maestro RR retains.
USIING YOUR STEERING WHEEL CONTROLS USING YOUR STEERING WHEEL CONTROLS (If equipped) Automotive Data Solutions Inc. © 2016 Your steering wheel buttons can be used to control your aftermarket Alpine radio. You can assign steering wheel buttons to Alpine radio functions. Simply program your Maestro RR module online using the Weblink updater and customize your buttons. Each steering wheel button can control up to two radio features.
USING YOUR FACTORY SYSTEMS USING YOUR FACTORY SYSTEMS HOW TO GET THERE: The following section explains how to access and operate the factory systems that have been retained. Your vehicle must already be equipped with these systems. OEM SATELLITE RADIO Press on Satellite Radio to listen to the factory satellite radio tuner. This allows you to use the tuner that’s already in your vehicle, rather than installing an aftermarket tuner.
USING MAESTRO FEATURES - VEHICLE INFO USING MAESTRO FEATURES VEHICLE INFO HOW TO GET THERE: VEHICLE INFORMATION Access And Display Vehicle Info Screen To access the maestro menu, press and hold the favorites button. Press on Vehicle Info to display information about the vehicle such as tire pressure, battery voltage and open entry points. If your vehicle is equipped with a compatible tire pressure monitoring system (TPMS), the digital tire pressures will be displayed for each tire.
USING MAESTRO FEATURES - GAUGES USING MAESTRO FEATURES GAUGES HOW TO GET THERE: GAUGES Access And Display Gauges Screen To access the Maestro menu, press and hold the Favorites button for 3 seconds. Press on Gauges to view the gauges that are selected. During the installation, the default gauge choices will be displayed. When the Maestro RR module is installed, the vehicle is queried and the gauges that can be supported are enabled.
USING MAESTRO FEATURES - GAUGES USING MAESTRO FEATURES GAUGES HOW TO GET THERE: MUTE 3 seconds Automotive Data Solutions Inc. © 2016 •OBD2 Communication Auto Disable (default) The module will communicate with the vehicle’s OBD2 system unless it detects another device. This may be a scan tool or aftermarket programmer connected to the vehicle. Always Enabled The module will communicate with the vehicle’s OBD2 system even when a scan tool or aftermarket programmer is connected.
USING MAESTRO FEATURES - PARKING ASSIST USING MAESTRO FEATURES PARKING ASSIST HOW TO GET THERE: PARKING ASSIST Access And Display Parking Assist Screen To access the Maestro menu, press and hold the Favorites button for 3 seconds. Press on Parking Assist to see the visual parking assist screen. This option will only be available if the Maestro detects that your vehicle is equipped a compatible factory parking sensor system.
CHANGING OTHER SETTINGS CHANGING OTHER SETTINGS HOW TO GET THERE: VEHICLE FACTORY SETTINGS Access And Change Vehicle factory Settings There are several programmable options that affect the way that the Maestro interface works with your vehicle. These settings enable you to customize the features of your vehicle. Not all settings are described here, as they are vehicle specific. • Vehicle Amplifier To adjust the settings of your factory amplifier, press on Vehicle Amplifier.
Owner's Guide TO1 & JVC radio RETAINS STEERING WHEEL CONTROLS, FACTORY SETTINGS AND MORE! PRODUCTS REQUIRED OPTIONAL ACCESSORIES PROGRAMMED FIRMWARE •iDatalink Maestro RR Radio Replacement Interface •TO1 Installation Harness ADS-RR(SR)-TOY01-DS NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.
TABLE OF CONTENTS WELCOME Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. This guide is a great addition to both the vehicle owner’s guide and the aftermarket radio owner’s guide. We recommand having both these documents handy as they cover all the functionality that the Maestro RR retains.
USIING YOUR STEERING WHEEL CONTROLS USING YOUR STEERING WHEEL CONTROLS (If equipped) Automotive Data Solutions Inc. © 2016 Your steering wheel buttons can be used to control your aftermarket JVC radio. You can assign steering wheel buttons to JVC radio functions. Simply program your Maestro RR module online using the Weblink updater and customize your buttons. Each steering wheel button can control up to two radio features.
USING YOUR FACTORY SYSTEMS USING YOUR FACTORY SYSTEMS HOW TO GET THERE: The following section explains how to access and operate the factory systems that have been retained. Your vehicle must already be equipped with these systems. OEM SATELLITE RADIO Press on Satellite Radio to listen to the factory satellite radio tuner. This allows you to use the tuner that’s already in your vehicle, rather than installing an aftermarket tuner.
USING MAESTRO FEATURES - VEHICLE INFO USING MAESTRO FEATURES VEHICLE INFO HOW TO GET THERE: VEHICLE INFO Access And Display Vehicle Info Screen In the My Vehicle submenu, press on Vehicle Info to display information about the vehicle such as tire pressure, battery voltage and open entry points. If your vehicle is equipped with a compatible tire pressure monitoring system (TPMS), the digital tire pressures will be displayed for each tire.
USING MAESTRO FEATURES - VEHICLE INFO USING MAESTRO FEATURES VEHICLE INFO Automotive Data Solutions Inc. © 2016 •Door Alert Enables the Vehicle Info screen to be displayed automatically if a door is opened or left open when the vehicle speed exceeds 5 mph or 8 km/h. •TPMS Alert Enables the Vehicle Info screen to be displayed automatically when a TPMS fault is detected (only if TPMS is available in the vehicle and supported by Maestro). JVC-RR(SR)-TOY01-DS-OG-EN maestro.idatalink.
USING MAESTRO FEATURES - GAUGES USING MAESTRO FEATURES GAUGES HOW TO GET THERE: GAUGES Access And Display Gauges Screen In the Vehicle Car submenu, press on Gauges to view the gauges that are selected. During the installation, the default gauge choices will be displayed. When the Maestro RR module is installed, the vehicle is queried and the gauges that can be supported are enabled.
USING MAESTRO FEATURES - GAUGES USING MAESTRO FEATURES GAUGES •Validate PIDs (Parameter Identifiers) Accesses the factory system to determine which gauges can be supported. This is done automatically when the module powers up. It is only required to be done manually if the module has been re-flashed. •About Gauges This screen will display a pop-up with information about the gauges.
USING MAESTRO FEATURES - PARKING ASSIST USING MAESTRO FEATURES PARKING ASSIST HOW TO GET THERE: PARKING ASSIST Access And Display Vehicle Info Screen In the My Vehicle submenu, press on Parking Assist to see the visual parking assist screen. This option will only be available if the Maestro detects that your vehicle is equipped a compatible factory parking sensor system.
CHANGING OTHER SETTINGS CHANGING OTHER SETTINGS HOW TO GET THERE: VEHICLE FACTORY SETTINGS Access And Change Vehicle factory Settings There are several programmable options that affect the way that the Maestro interface works with your vehicle. These settings enable you to customize the features of your vehicle. Not all settings are described here, as they are vehicle specific. • Vehicle Amplifier To adjust the settings of your factory amplifier, press on Vehicle Amplifier.
Owner's Guide TO1 & Kenwood radio RETAINS STEERING WHEEL CONTROLS, FACTORY SETTINGS AND MORE! PRODUCTS REQUIRED OPTIONAL ACCESSORIES PROGRAMMED FIRMWARE •iDatalink Maestro RR Radio Replacement Interface •TO1 Installation Harness ADS-RR(SR)-TOY01-DS NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.
TABLE OF CONTENTS WELCOME Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. This guide is a great addition to both the vehicle owner’s guide and the aftermarket radio owner’s guide. We recommand having both these documents handy as they cover all the functionality that the Maestro RR retains.
USIING YOUR STEERING WHEEL CONTROLS USING YOUR STEERING WHEEL CONTROLS (If equipped) Automotive Data Solutions Inc. © 2016 Your steering wheel buttons can be used to control your aftermarket Kenwood radio. You can assign steering wheel buttons to Kenwood radio functions. Simply program your Maestro RR module online using the Weblink updater and customize your buttons. Each steering wheel button can control up to two radio features.
USING YOUR FACTORY SYSTEMS USING YOUR FACTORY SYSTEMS HOW TO GET THERE: The following section explains how to access and operate the factory systems that have been retained. Your vehicle must already be equipped with these systems. OEM SATELLITE RADIO Press on Satellite Radio to listen to the factory satellite radio tuner. This allows you to use the tuner that’s already in your vehicle, rather than installing an aftermarket tuner.
USING MAESTRO FEATURES - VEHICLE INFO USING MAESTRO FEATURES VEHICLE INFO Maestro features can be accessed in the My Car submenu. If an icon is not active (gray color) then it is not available in your vehicle or it was disabled when the Maestro module was programmed using Weblink. The options described here may not be available in your vehicle.
USING MAESTRO FEATURES - VEHICLE INFO USING MAESTRO FEATURES VEHICLE INFO Maestro features can be accessed in the My Car submenu. If an icon is not active (gray color) then it is not available in your vehicle or it was disabled when the Maestro module was programmed using Weblink. The options described here may not be available in your vehicle. •Door Alert Enables the Vehicle Info screen to be displayed automatically if a door is opened or left open when the vehicle speed exceeds 5 mph or 8 km/h.
USING MAESTRO FEATURES - GAUGES USING MAESTRO FEATURES GAUGES Maestro features can be accessed in the My Car submenu. If an icon is not active (gray color) then it is not available in your vehicle or it was disabled when the Maestro module was programmed using Weblink. The options described here may not be available in your vehicle. HOW TO GET THERE: GAUGES Access And Display Gauges Screen In the My Car submenu, press on Gauges to view the gauges that are selected.
USING MAESTRO FEATURES - GAUGES USING MAESTRO FEATURES GAUGES Maestro features can be accessed in the My Car submenu. If an icon is not active (gray color) then it is not available in your vehicle or it was disabled when the Maestro module was programmed using Weblink. The options described here may not be available in your vehicle. HOW TO GET THERE: •Fuel Economy For accurate fuel economy information, the fuel tank capacity must be entered in this section of the settings menu.
USING MAESTRO FEATURES - PARKING ASSIST USING MAESTRO FEATURES PARKING ASSIST Maestro features can be accessed in the My Car submenu. If an icon is not active (gray color) then it is not available in your vehicle or it was disabled when the Maestro module was programmed using Weblink. The options described here may not be available in your vehicle. PARKING ASSIST Access And Display Parking Assist Screen In the My Car submenu, press on Parking Assist to see the visual parking assist screen.
CHANGING OTHER SETTINGS CHANGING OTHER SETTINGS HOW TO GET THERE: VEHICLE FACTORY SETTINGS Access And Change Vehicle factory Settings There are several programmable options that affect the way that the Maestro interface works with your vehicle. These settings enable you to customize the features of your vehicle. Not all settings are described here, as they are vehicle specific. • Vehicle Amplifier To adjust the settings of your factory amplifier, press on Vehicle Amplifier.
Owner's Guide TO1 & Pioneer radio RETAINS STEERING WHEEL CONTROLS, FACTORY SETTINGS AND MORE! PRODUCTS REQUIRED OPTIONAL ACCESSORIES PROGRAMMED FIRMWARE •iDatalink Maestro RR Radio Replacement Interface •TO1 Installation Harness ADS-RR(SR)-TOY01-DS NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.
TABLE OF CONTENTS WELCOME Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. This guide is a great addition to both the vehicle owner’s guide and the aftermarket radio owner’s guide. We recommand having both these documents handy as they cover all the functionality that the Maestro RR retains.
USIING YOUR STEERING WHEEL CONTROLS USING YOUR STEERING WHEEL CONTROLS (If equipped) Automotive Data Solutions Inc. © 2016 Your steering wheel buttons can be used to control your aftermarket Pioneer radio. You can assign steering wheel buttons to Pioneer radio functions. Simply program your Maestro RR module online using the Weblink updater and customize your buttons. Each steering wheel button can control up to two radio features.
USING YOUR FACTORY SYSTEMS USING FACTORY SETTINGS The following section explains how to access and operate the factory systems that have been retained. Your vehicle must already be equipped with these systems. OEM SATELLITE RADIO Press on Satellite Radio to listen to the factory satellite radio tuner. This allows you to use the tuner that’s already in your vehicle, rather than installing an aftermarket tuner. Your vehicle must be equipped with a tuner for it be retained by the Maestro RR module.
USING MAESTRO FEATURES - VEHICLE INFO USING MAESTRO FEATURES VEHICLE INFO HOW TO GET THERE: VEHICLE INFORMATION Access And Display Vehicle Info Screen To access Maestro features, enter the My Vehicle menu. Press on the Vehicle Info icon to display information about the vehicle such as tire pressure, battery voltage and open entry points. If your vehicle is equipped with a compatible tire pressure monitoring system (TPMS), the digital tire pressures will be displayed for each tire.
USING MAESTRO FEATURES - GAUGES USING MAESTRO FEATURES GAUGES HOW TO GET THERE: GAUGES Access And Display Gauges Screen In the My Vehicle menu, press on Gauges icon to view the gauges that are selected. The display style of the gauge can be changed by tapping the face of each gauge. You can also press and hold each gauge to configure it. During the installation, the default gauge choices will be displayed.
USING MAESTRO FEATURES - GAUGES USING MAESTRO FEATURES GAUGES HOW TO GET THERE: •OBD2 Communication Auto Disable (default) The module will communicate with the vehicle’s OBD2 system unless it detects another device. This may be a scan tool or aftermarket programmer connected to the vehicle. Always Enabled The module will communicate with the vehicle’s OBD2 system even when a scan tool or aftermarket programmer is connected.
USING MAESTRO FEATURES - PARKING ASSIST USING MAESTRO FEATURES PARKING ASSIST PARKING ASSIST Access And Display Parking Assist Screen In the My Vehicle menu, press on Parking Assist to see the visual parking assist screen. This option will only be available if the Maestro detects that your vehicle is equipped a compatible factory parking sensor system. HOW TO GET THERE: Access And Change Parking Assist Settings In the Parking Assist screen, press the Settings button to configure this feature.
CHANGING OTHER SETTINGS CHANGING OTHER SETTINGS HOW TO GET THERE: VEHICLE FACTORY SETTINGS Access And Change Vehicle factory Settings There are several programmable options that affect the way that the Maestro interface works with your vehicle. These settings enable you to customize the features of your vehicle. Not all settings are described here, as they are vehicle specific. • Vehicle Amplifier To adjust the settings of your factory amplifier, press on Vehicle Amplifier.
INSTALL GUIDE 2012-2016 Scion iQ RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro TO1 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY01-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Scion iQ 2012-2016 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Installation Instructions 3 Wiring Diagram 4 Radio Wire Reference Chart 5 Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware for your vehicle and that you carefully review the install guide.
Scion iQ 2012-2016 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on the next page from aftermarket radio main harness to the TO1 T-harness and match the wire functions. • Remove the factory radio. STEP 2 • If the vehicle is equipped with an OEM backup camera, connect the TO1 T-harness to the backup camera harness (see wire chart for details). STEP 3 • Identify if your vehicle has a 20 or 28 pin secondary connector.
Scion iQ 2012-2016 WIRING DIAGRAM without an Amplifier STEP 5 STEP 1 WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Scion iQ 2012-2016 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A N/A VSS (ve
Scion iQ 2012-2016 VEHICLE WIRE REFERENCE CHART REVERSE CAMERA NOT AVAILABLE / NOT PRESENT Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-TOY01-DS-IG-EN maestro.idatalink.
Scion iQ 2012-2016 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended. Reset the RR.
INSTALL GUIDE 2007-2016 Scion tC RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro TO1 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY01-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Scion tC 2007-2016 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Installation Instructions 3 Wiring Diagram 4 Radio Wire Reference Chart 5 Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware for your vehicle and that you carefully review the install guide.
Scion tC 2007-2016 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on the next page from aftermarket radio main harness to the TO1 T-harness and match the wire functions. • Remove the factory radio. STEP 2 • If the vehicle is equipped with an OEM backup camera, connect the TO1 T-harness to the backup camera harness (see wire chart for details). STEP 3 • Identify if your vehicle has a 20 or 28 pin secondary connector.
Scion tC 2007-2016 WIRING DIAGRAM without an Amplifier STEP 5 STEP 1 WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Scion tC 2007-2016 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A N/A VSS (ve
Scion tC 2007-2016 VEHICLE WIRE REFERENCE CHART REVERSE CAMERA NOT AVAILABLE / NOT PRESENT Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-TOY01-DS-IG-EN maestro.idatalink.
Scion tC 2007-2016 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended. Reset the RR.
INSTALL GUIDE 2008-2016 Scion xB RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro TO1 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY01-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Scion xB 2008-2016 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Installation Instructions 3 Wiring Diagram 4 Radio Wire Reference Chart 5 Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware for your vehicle and that you carefully review the install guide.
Scion xB 2008-2016 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on the next page from aftermarket radio main harness to the TO1 T-harness and match the wire functions. • Remove the factory radio. STEP 2 • If the vehicle is equipped with an OEM backup camera, connect the TO1 T-harness to the backup camera harness (see wire chart for details). STEP 3 • Identify if your vehicle has a 20 or 28 pin secondary connector.
Scion xB 2008-2016 WIRING DIAGRAM without an Amplifier STEP 5 STEP 1 WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Scion xB 2008-2016 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A N/A VSS (ve
Scion xB 2008-2016 VEHICLE WIRE REFERENCE CHART REVERSE CAMERA NOT AVAILABLE / NOT PRESENT Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-TOY01-DS-IG-EN maestro.idatalink.
Scion xB 2008-2016 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended. Reset the RR.
INSTALL GUIDE 2008-2014 Scion xD RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro TO1 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY01-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Scion xD 2008-2014 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Installation Instructions 3 Wiring Diagram 4 Radio Wire Reference Chart 5 Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware for your vehicle and that you carefully review the install guide.
Scion xD 2008-2014 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on the next page from aftermarket radio main harness to the TO1 T-harness and match the wire functions. • Remove the factory radio. STEP 2 • If the vehicle is equipped with an OEM backup camera, connect the TO1 T-harness to the backup camera harness (see wire chart for details). STEP 3 • Identify if your vehicle has a 20 or 28 pin secondary connector.
Scion xD 2008-2014 WIRING DIAGRAM without an Amplifier STEP 5 STEP 1 WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Scion xD 2008-2014 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A N/A VSS (ve
Scion xD 2008-2014 VEHICLE WIRE REFERENCE CHART REVERSE CAMERA NOT AVAILABLE / NOT PRESENT Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-TOY01-DS-IG-EN maestro.idatalink.
Scion xD 2008-2014 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended. Reset the RR.
INSTALL GUIDE 2005-2011 Toyota 4 Runner With JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro TO1 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY01-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Toyota 4 Runner With JBL 2005-2011 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Toyota 4 Runner With JBL 2005-2011 INSTALLATION INSTRUCTIONS STEP 6 STEP 1 • Connect all the harnesses to the Maestro RR module then test your installation. • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on the next page from aftermarket radio main harness to the TO1 T-harness and match the wire functions. • Remove the factory radio.
Toyota 4 Runner With JBL 2005-2011 WIRING DIAGRAM with an Amplifier STEP 5 STEP 1 WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota 4 Runner With JBL 2005-2011 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+) Yellow/Black Yellow/Black N⁄A N
Toyota 4 Runner With JBL 2005-2011 VEHICLE WIRE REFERENCE CHART 2006-2009 Wire Description Connector Name Connector Color Connector Type Position Wire Color Polarity Wire Location Camera Power ~ ~ 24 pin 24 Red (+) Reverse camera harness Ground ~ ~ 24 pin 21 White (-) Reverse camera harness Video + ~ ~ 24 pin 22 Black (+) Reverse camera harness Video - ~ ~ 24 pin 23 Shield (-) Reverse camera harness Wire Description Connector Name Connector Color Connector Type P
Toyota 4 Runner With JBL 2005-2011 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended. Reset the RR.
INSTALL GUIDE 2012-2013 Toyota 4 Runner With JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro TO1 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY01-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Toyota 4 Runner With JBL 2012-2013 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Toyota 4 Runner With JBL 2012-2013 INSTALLATION INSTRUCTIONS STEP 6 STEP 1 • Connect all the harnesses to the Maestro RR module then test your installation. • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on the next page from aftermarket radio main harness to the TO1 T-harness and match the wire functions. • Remove the factory radio.
Toyota 4 Runner With JBL 2012-2013 WIRING DIAGRAM with an Amplifier STEP 5 STEP 1 WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota 4 Runner With JBL 2012-2013 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+) Yellow/Black Yellow/Black N⁄A N
Toyota 4 Runner With JBL 2012-2013 VEHICLE WIRE REFERENCE CHART Wire Description Connector Name Connector Color Connector Type Position Wire Color Polarity Wire Location Camera Power ~ ~ 24 pin 24 Red (+) Reverse camera harness Ground ~ ~ 24 pin 21 Shield (-) Reverse camera harness Video + ~ ~ 24 pin 22 White (+) Reverse camera harness Video - ~ ~ 24 pin 23 Black (-) Reverse camera harness Wire Description Connector Name Connector Color Connector Type Position W
Toyota 4 Runner With JBL 2012-2013 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended. Reset the RR.
INSTALL GUIDE 2005-2011 Toyota 4 Runner Without JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro TO1 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY01-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Toyota 4 Runner Without JBL 2005-2011 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Toyota 4 Runner Without JBL 2005-2011 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on the next page from aftermarket radio main harness to the TO1 T-harness and match the wire functions. • Remove the factory radio. STEP 2 • If the vehicle is equipped with an OEM backup camera, connect the TO1 T-harness to the backup camera harness (see wire chart for details). STEP 3 • Identify if your vehicle has a 20 or 28 pin secondary connector.
Toyota 4 Runner Without JBL 2005-2011 WIRING DIAGRAM without an Amplifier STEP 5 STEP 1 WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota 4 Runner Without JBL 2005-2011 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+) Yellow/Black Yellow/Black N⁄A
Toyota 4 Runner Without JBL 2005-2011 VEHICLE WIRE REFERENCE CHART REVERSE CAMERA NOT AVAILABLE / NOT PRESENT Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-TOY01-DS-IG-EN maestro.idatalink.
Toyota 4 Runner Without JBL 2005-2011 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended. Reset the RR.
INSTALL GUIDE 2012-2013 Toyota 4 Runner Without JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro TO1 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY01-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Toyota 4 Runner Without JBL 2012-2013 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Toyota 4 Runner Without JBL 2012-2013 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on the next page from aftermarket radio main harness to the TO1 T-harness and match the wire functions. • Remove the factory radio. STEP 2 • If the vehicle is equipped with an OEM backup camera, connect the TO1 T-harness to the backup camera harness (see wire chart for details). STEP 3 • Identify if your vehicle has a 20 or 28 pin secondary connector.
Toyota 4 Runner Without JBL 2012-2013 WIRING DIAGRAM without an Amplifier STEP 5 STEP 1 WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota 4 Runner Without JBL 2012-2013 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+) Yellow/Black Yellow/Black N⁄A
Toyota 4 Runner Without JBL 2012-2013 VEHICLE WIRE REFERENCE CHART Wire Description Connector Name Connector Color Connector Type Position Wire Color Polarity Wire Location Camera Power ~ ~ 24 pin 24 Red (+) Reverse camera harness Ground ~ ~ 24 pin 21 Shield (-) Reverse camera harness Video + ~ ~ 24 pin 22 White (+) Reverse camera harness Video - ~ ~ 24 pin 23 Black (-) Reverse camera harness Wire Description Connector Name Connector Color Connector Type Position
Toyota 4 Runner Without JBL 2012-2013 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended. Reset the RR.
INSTALL GUIDE 2011-2012 Toyota Avalon With JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro TO1 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY01-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Toyota Avalon With JBL 2011-2012 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Toyota Avalon With JBL 2011-2012 INSTALLATION INSTRUCTIONS STEP 6 STEP 1 • Connect all the harnesses to the Maestro RR module then test your installation. • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on the next page from aftermarket radio main harness to the TO1 T-harness and match the wire functions. • Remove the factory radio.
Toyota Avalon With JBL 2011-2012 WIRING DIAGRAM with an Amplifier STEP 5 STEP 1 WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Avalon With JBL 2011-2012 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A
Toyota Avalon With JBL 2011-2012 VEHICLE WIRE REFERENCE CHART Wire Description Connector Name Connector Color Connector Type Position Wire Color Polarity Wire Location Camera Power ~ ~ 24 pin 24 Green (+) Reverse camera harness Ground ~ ~ 24 pin 21 Shield (-) Reverse camera harness Video + ~ ~ 24 pin 22 Blue (+) Reverse camera harness Video - ~ ~ 24 pin 23 Pink (-) Reverse camera harness REVERSE CAMERA CONNECTOR (WIRE SIDE) 1 2 3 4 5 6 7 8 9 10 11 12 13 14
Toyota Avalon With JBL 2011-2012 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended. Reset the RR.
INSTALL GUIDE 2013-2014 Toyota Avalon With JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro TO1 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY01-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Toyota Avalon With JBL 2013-2014 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Toyota Avalon With JBL 2013-2014 INSTALLATION INSTRUCTIONS STEP 6 STEP 1 • Connect all the harnesses to the Maestro RR module then test your installation. • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on the next page from aftermarket radio main harness to the TO1 T-harness and match the wire functions. • Remove the factory radio.
Toyota Avalon With JBL 2013-2014 WIRING DIAGRAM with an Amplifier STEP 5 STEP 1 WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Avalon With JBL 2013-2014 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A
Toyota Avalon With JBL 2013-2014 VEHICLE WIRE REFERENCE CHART Wire Description Connector Name Connector Color Connector Type Position Wire Color Polarity Wire Location Camera Power ~ ~ 16 pin 07 Red (+) Reverse camera harness Ground ~ ~ 16 pin 15 Shield (-) Reverse camera harness Video + ~ ~ 16 pin 08 White (+) Reverse camera harness Video - ~ ~ 16 pin 16 Black (-) Reverse camera harness REVERSE CAMERA CONNECTOR (WIRE SIDE) 8 7 6 5 4 3 2 1 16 15 14 13 12 11
Toyota Avalon With JBL 2013-2014 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended. Reset the RR.
INSTALL GUIDE 2011-2012 Toyota Avalon Without JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro TO1 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY01-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Toyota Avalon Without JBL 2011-2012 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Toyota Avalon Without JBL 2011-2012 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on the next page from aftermarket radio main harness to the TO1 T-harness and match the wire functions. • Remove the factory radio. STEP 2 • If the vehicle is equipped with an OEM backup camera, connect the TO1 T-harness to the backup camera harness (see wire chart for details). STEP 3 • Identify if your vehicle has a 20 or 28 pin secondary connector.
Toyota Avalon Without JBL 2011-2012 WIRING DIAGRAM without an Amplifier STEP 5 STEP 1 WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Avalon Without JBL 2011-2012 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+) Yellow/Black Yellow/Black N⁄A
Toyota Avalon Without JBL 2011-2012 VEHICLE WIRE REFERENCE CHART Wire Description Connector Name Connector Color Connector Type Position Wire Color Polarity Wire Location Camera Power ~ ~ 24 pin 24 Green (+) Reverse camera harness Ground ~ ~ 24 pin 21 Shield (-) Reverse camera harness Video + ~ ~ 24 pin 22 Blue (+) Reverse camera harness Video - ~ ~ 24 pin 23 Pink (-) Reverse camera harness REVERSE CAMERA CONNECTOR (WIRE SIDE) 1 2 3 4 5 6 7 8 9 10 11 12 13
Toyota Avalon Without JBL 2011-2012 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended. Reset the RR.
INSTALL GUIDE 2013-2014 Toyota Avalon Without JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro TO1 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY01-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Toyota Avalon Without JBL 2013-2014 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Toyota Avalon Without JBL 2013-2014 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on the next page from aftermarket radio main harness to the TO1 T-harness and match the wire functions. • Remove the factory radio. STEP 2 • If the vehicle is equipped with an OEM backup camera, connect the TO1 T-harness to the backup camera harness (see wire chart for details). STEP 3 • Identify if your vehicle has a 20 or 28 pin secondary connector.
Toyota Avalon Without JBL 2013-2014 WIRING DIAGRAM without an Amplifier STEP 5 STEP 1 WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Avalon Without JBL 2013-2014 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+) Yellow/Black Yellow/Black N⁄A
Toyota Avalon Without JBL 2013-2014 VEHICLE WIRE REFERENCE CHART Wire Description Connector Name Connector Color Connector Type Position Wire Color Polarity Wire Location Camera Power ~ ~ 16 pin 07 Black (+) Reverse camera harness Ground ~ ~ 16 pin 15 Shield (-) Reverse camera harness Video + ~ ~ 16 pin 08 White (+) Reverse camera harness Video - ~ ~ 16 pin 16 Red (-) Reverse camera harness REVERSE CAMERA CONNECTOR (WIRE SIDE) 8 7 6 5 4 3 2 1 16 15 14 13 12
Toyota Avalon Without JBL 2013-2014 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended. Reset the RR.
INSTALL GUIDE 2018 Toyota C-HR RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro TO1 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY01-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Toyota C-HR 2018 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Installation Instructions 3 Wiring Diagram 4 Radio Wire Reference Chart 5 Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware for your vehicle and that you carefully review the install guide.
Toyota C-HR 2018 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on the next page from aftermarket radio main harness to the TO1 T-harness and match the wire functions. • Remove the factory radio. STEP 2 • If the vehicle is equipped with an OEM backup camera, connect the TO1 T-harness to the backup camera harness (see wire chart for details). STEP 3 • Identify if your vehicle has a 20 or 28 pin secondary connector.
Toyota C-HR 2018 WIRING DIAGRAM without an Amplifier STEP 5 STEP 1 WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota C-HR 2018 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A N/A VSS (vehi
Toyota C-HR 2018 VEHICLE WIRE REFERENCE CHART REVERSE CAMERA NOT AVAILABLE / NOT PRESENT Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-TOY01-DS-IG-EN maestro.idatalink.
Toyota C-HR 2018 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended. Reset the RR.
INSTALL GUIDE 2007-2011 Toyota Camry With JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro TO1 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY01-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Toyota Camry With JBL 2007-2011 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Installation Instructions 3 Wiring Diagram 4 Radio Wire Reference Chart 5 Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware for your vehicle and that you carefully review the install guide.
Toyota Camry With JBL 2007-2011 INSTALLATION INSTRUCTIONS STEP 6 STEP 1 • Connect all the harnesses to the Maestro RR module then test your installation. • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on the next page from aftermarket radio main harness to the TO1 T-harness and match the wire functions. • Remove the factory radio.
Toyota Camry With JBL 2007-2011 WIRING DIAGRAM with an Amplifier STEP 5 STEP 1 WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Camry With JBL 2007-2011 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A
Toyota Camry With JBL 2007-2011 VEHICLE WIRE REFERENCE CHART Wire Description Connector Name Connector Color Connector Type Position Wire Color Polarity Wire Location Camera Power ~ ~ 24 pin 24 Black (+) Reverse camera harness Ground ~ ~ 24 pin 21 Shield (-) Reverse camera harness Video + ~ ~ 24 pin 22 Red (+) Reverse camera harness Video - ~ ~ 24 pin 23 White (-) Reverse camera harness REVERSE CAMERA CONNECTOR (WIRE SIDE) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 1
Toyota Camry With JBL 2007-2011 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended. Reset the RR.
INSTALL GUIDE 2012-2014 Toyota Camry Without Factory Screen RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro TO1 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY01-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Toyota Camry Without Factory Screen 2012-2014 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Toyota Camry Without Factory Screen 2012-2014 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on the next page from aftermarket radio main harness to the TO1 T-harness and match the wire functions. • Remove the factory radio. STEP 2 • If the vehicle is equipped with an OEM backup camera, connect the TO1 T-harness to the backup camera harness (see wire chart for details).
Toyota Camry Without Factory Screen 2012-2014 WIRING DIAGRAM without an Amplifier STEP 5 STEP 1 WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Camry Without Factory Screen 2012-2014 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+) Yellow/Black Yellow/Bl
Toyota Camry Without Factory Screen 2012-2014 VEHICLE WIRE REFERENCE CHART Wire Description Connector Name Connector Color Connector Type Position Wire Color Polarity Wire Location Camera Power ~ ~ 16 pin 07 Black (+) Reverse camera harness Ground ~ ~ 16 pin 15 Shield (-) Reverse camera harness Video + ~ ~ 16 pin 08 White (+) Reverse camera harness Video - ~ ~ 16 pin 16 Red (-) Reverse camera harness REVERSE CAMERA CONNECTOR (WIRE SIDE) 8 7 6 5 4 3 2 1 16 15
Toyota Camry Without Factory Screen 2012-2014 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended.
INSTALL GUIDE 2007-2011 Toyota Camry Without JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro TO1 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY01-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Toyota Camry Without JBL 2007-2011 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Toyota Camry Without JBL 2007-2011 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on the next page from aftermarket radio main harness to the TO1 T-harness and match the wire functions. • Remove the factory radio. STEP 2 • If the vehicle is equipped with an OEM backup camera, connect the TO1 T-harness to the backup camera harness (see wire chart for details). STEP 3 • Identify if your vehicle has a 20 or 28 pin secondary connector.
Toyota Camry Without JBL 2007-2011 WIRING DIAGRAM without an Amplifier STEP 5 STEP 1 WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Camry Without JBL 2007-2011 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+) Yellow/Black Yellow/Black N⁄A N
Toyota Camry Without JBL 2007-2011 VEHICLE WIRE REFERENCE CHART Wire Description Connector Name Connector Color Connector Type Position Wire Color Polarity Wire Location Camera Power ~ ~ 24 pin 24 Black (+) Reverse camera harness Ground ~ ~ 24 pin 21 Shield (-) Reverse camera harness Video + ~ ~ 24 pin 22 Red (+) Reverse camera harness Video - ~ ~ 24 pin 23 White (-) Reverse camera harness REVERSE CAMERA CONNECTOR (WIRE SIDE) 1 2 3 4 5 6 7 8 9 10 11 12 13 1
Toyota Camry Without JBL 2007-2011 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended. Reset the RR.
INSTALL GUIDE 2017-2018 Toyota Corolla iM RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro TO1 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY01-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Toyota Corolla iM 2017-2018 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Installation Instructions 3 Wiring Diagram 4 Radio Wire Reference Chart 5 Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware for your vehicle and that you carefully review the install guide.
Toyota Corolla iM 2017-2018 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on the next page from aftermarket radio main harness to the TO1 T-harness and match the wire functions. • Remove the factory radio. STEP 2 • If the vehicle is equipped with an OEM backup camera, connect the TO1 T-harness to the backup camera harness (see wire chart for details). STEP 3 • Identify if your vehicle has a 20 or 28 pin secondary connector.
Toyota Corolla iM 2017-2018 WIRING DIAGRAM without an Amplifier STEP 5 STEP 1 WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Corolla iM 2017-2018 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A N/A
Toyota Corolla iM 2017-2018 VEHICLE WIRE REFERENCE CHART Wire Description Connector Name Connector Color Connector Type Position Wire Color Polarity Wire Location Camera Power ~ ~ 24 pin 11 Red (+) Reverse camera harness Ground ~ ~ 24 pin 23 Shield (-) Reverse camera harness Video + ~ ~ 24 pin 12 Black (+) Reverse camera harness Video - ~ ~ 24 pin 24 White (-) Reverse camera harness REVERSE CAMERA CONNECTORS (WIRE SIDE) 12 11 10 9 8 7 6 5 4 3 2 1 24 23 22 2
Toyota Corolla iM 2017-2018 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended. Reset the RR.
INSTALL GUIDE 2009-2013 Toyota Corolla With JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro TO1 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY01-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Toyota Corolla With JBL 2009-2013 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Toyota Corolla With JBL 2009-2013 INSTALLATION INSTRUCTIONS STEP 6 STEP 1 • Connect all the harnesses to the Maestro RR module then test your installation. • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on the next page from aftermarket radio main harness to the TO1 T-harness and match the wire functions. • Remove the factory radio.
Toyota Corolla With JBL 2009-2013 WIRING DIAGRAM with an Amplifier STEP 5 STEP 1 WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Corolla With JBL 2009-2013 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄
Toyota Corolla With JBL 2009-2013 VEHICLE WIRE REFERENCE CHART REVERSE CAMERA NOT AVAILABLE / NOT PRESENT Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-TOY01-DS-IG-EN maestro.idatalink.
Toyota Corolla With JBL 2009-2013 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended. Reset the RR.
INSTALL GUIDE 2014-2015 Toyota Corolla Without Factory Screen RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro TO1 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY01-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Toyota Corolla Without Factory Screen 2014-2015 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Toyota Corolla Without Factory Screen 2014-2015 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on the next page from aftermarket radio main harness to the TO1 T-harness and match the wire functions. • Remove the factory radio. STEP 2 • If the vehicle is equipped with an OEM backup camera, connect the TO1 T-harness to the backup camera harness (see wire chart for details).
Toyota Corolla Without Factory Screen 2014-2015 WIRING DIAGRAM without an Amplifier STEP 5 STEP 1 WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Corolla Without Factory Screen 2014-2015 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+) Yellow/Black Yellow/
Toyota Corolla Without Factory Screen 2014-2015 VEHICLE WIRE REFERENCE CHART REVERSE CAMERA NOT AVAILABLE / NOT PRESENT Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-TOY01-DS-IG-EN maestro.idatalink.
Toyota Corolla Without Factory Screen 2014-2015 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended.
INSTALL GUIDE 2009-2013 Toyota Corolla Without JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro TO1 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY01-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Toyota Corolla Without JBL 2009-2013 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Toyota Corolla Without JBL 2009-2013 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on the next page from aftermarket radio main harness to the TO1 T-harness and match the wire functions. • Remove the factory radio. STEP 2 • If the vehicle is equipped with an OEM backup camera, connect the TO1 T-harness to the backup camera harness (see wire chart for details). STEP 3 • Identify if your vehicle has a 20 or 28 pin secondary connector.
Toyota Corolla Without JBL 2009-2013 WIRING DIAGRAM without an Amplifier STEP 5 STEP 1 WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Corolla Without JBL 2009-2013 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+) Yellow/Black Yellow/Black N⁄A
Toyota Corolla Without JBL 2009-2013 VEHICLE WIRE REFERENCE CHART REVERSE CAMERA NOT AVAILABLE / NOT PRESENT Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-TOY01-DS-IG-EN maestro.idatalink.
Toyota Corolla Without JBL 2009-2013 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended. Reset the RR.
INSTALL GUIDE 2006-2014 Toyota FJ Cruiser With JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro TO1 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY01-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Toyota FJ Cruiser With JBL 2006-2014 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Toyota FJ Cruiser With JBL 2006-2014 INSTALLATION INSTRUCTIONS STEP 6 STEP 1 • Connect all the harnesses to the Maestro RR module then test your installation. • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on the next page from aftermarket radio main harness to the TO1 T-harness and match the wire functions. • Remove the factory radio.
Toyota FJ Cruiser With JBL 2006-2014 WIRING DIAGRAM with an Amplifier STEP 5 STEP 1 WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota FJ Cruiser With JBL 2006-2014 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+) Yellow/Black Yellow/Black N⁄A
Toyota FJ Cruiser With JBL 2006-2014 VEHICLE WIRE REFERENCE CHART REVERSE CAMERA NOT AVAILABLE / NOT PRESENT Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-TOY01-DS-IG-EN maestro.idatalink.
Toyota FJ Cruiser With JBL 2006-2014 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended. Reset the RR.
INSTALL GUIDE 2006-2014 Toyota FJ Cruiser Without JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro TO1 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY01-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Toyota FJ Cruiser Without JBL 2006-2014 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Toyota FJ Cruiser Without JBL 2006-2014 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on the next page from aftermarket radio main harness to the TO1 T-harness and match the wire functions. • Remove the factory radio. STEP 2 • If the vehicle is equipped with an OEM backup camera, connect the TO1 T-harness to the backup camera harness (see wire chart for details).
Toyota FJ Cruiser Without JBL 2006-2014 WIRING DIAGRAM without an Amplifier STEP 5 STEP 1 WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota FJ Cruiser Without JBL 2006-2014 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+) Yellow/Black Yellow/Black N
Toyota FJ Cruiser Without JBL 2006-2014 VEHICLE WIRE REFERENCE CHART REVERSE CAMERA NOT AVAILABLE / NOT PRESENT Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-TOY01-DS-IG-EN maestro.idatalink.
Toyota FJ Cruiser Without JBL 2006-2014 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended. Reset the RR.
INSTALL GUIDE 2008-2012 Toyota Highlander With JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro TO1 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY01-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Toyota Highlander With JBL 2008-2012 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Toyota Highlander With JBL 2008-2012 INSTALLATION INSTRUCTIONS STEP 6 STEP 1 • Connect all the harnesses to the Maestro RR module then test your installation. • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on the next page from aftermarket radio main harness to the TO1 T-harness and match the wire functions. • Remove the factory radio.
Toyota Highlander With JBL 2008-2012 WIRING DIAGRAM with an Amplifier STEP 5 STEP 1 WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Highlander With JBL 2008-2012 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+) Yellow/Black Yellow/Black N⁄A
Toyota Highlander With JBL 2008-2012 VEHICLE WIRE REFERENCE CHART Wire Description Connector Name Connector Color Connector Type Position Wire Color Polarity Wire Location Camera Power ~ ~ 24 pin 24 Black (+) Reverse camera harness Ground ~ ~ 24 pin 21 White (-) Reverse camera harness Video + ~ ~ 24 pin 22 Red (+) Reverse camera harness Video - ~ ~ 24 pin 23 Shield (-) Reverse camera harness Wire Description Connector Name Connector Color Connector Type Position
Toyota Highlander With JBL 2008-2012 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended. Reset the RR.
INSTALL GUIDE 2013 Toyota Highlander With JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro TO1 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY01-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Toyota Highlander With JBL 2013 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Installation Instructions 3 Wiring Diagram 4 Radio Wire Reference Chart 5 Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware for your vehicle and that you carefully review the install guide.
Toyota Highlander With JBL 2013 INSTALLATION INSTRUCTIONS STEP 6 STEP 1 • Connect all the harnesses to the Maestro RR module then test your installation. • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on the next page from aftermarket radio main harness to the TO1 T-harness and match the wire functions. • Remove the factory radio.
Toyota Highlander With JBL 2013 WIRING DIAGRAM with an Amplifier STEP 5 STEP 1 WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Highlander With JBL 2013 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A
Toyota Highlander With JBL 2013 VEHICLE WIRE REFERENCE CHART Wire Description Connector Name Connector Color Connector Type Position Wire Color Polarity Wire Location Camera Power ~ ~ 24 pin 24 Black (+) Reverse camera harness Ground ~ ~ 24 pin 21 White (-) Reverse camera harness Video + ~ ~ 24 pin 22 Red (+) Reverse camera harness Video - ~ ~ 24 pin 23 Shield (-) Reverse camera harness Wire Description Connector Name Connector Color Connector Type Position Wire
Toyota Highlander With JBL 2013 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended. Reset the RR.
INSTALL GUIDE 2008-2012 Toyota Highlander Without JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro TO1 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY01-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Toyota Highlander Without JBL 2008-2012 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Toyota Highlander Without JBL 2008-2012 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on the next page from aftermarket radio main harness to the TO1 T-harness and match the wire functions. • Remove the factory radio. STEP 2 • If the vehicle is equipped with an OEM backup camera, connect the TO1 T-harness to the backup camera harness (see wire chart for details).
Toyota Highlander Without JBL 2008-2012 WIRING DIAGRAM without an Amplifier STEP 5 STEP 1 WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Highlander Without JBL 2008-2012 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+) Yellow/Black Yellow/Black N
Toyota Highlander Without JBL 2008-2012 VEHICLE WIRE REFERENCE CHART REVERSE CAMERA NOT AVAILABLE / NOT PRESENT Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-TOY01-DS-IG-EN maestro.idatalink.
Toyota Highlander Without JBL 2008-2012 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended. Reset the RR.
INSTALL GUIDE 2013 Toyota Highlander Without JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro TO1 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY01-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Toyota Highlander Without JBL 2013 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Toyota Highlander Without JBL 2013 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on the next page from aftermarket radio main harness to the TO1 T-harness and match the wire functions. • Remove the factory radio. STEP 2 • If the vehicle is equipped with an OEM backup camera, connect the TO1 T-harness to the backup camera harness (see wire chart for details). STEP 3 • Identify if your vehicle has a 20 or 28 pin secondary connector.
Toyota Highlander Without JBL 2013 WIRING DIAGRAM without an Amplifier STEP 5 STEP 1 WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Highlander Without JBL 2013 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+) Yellow/Black Yellow/Black N⁄A N
Toyota Highlander Without JBL 2013 VEHICLE WIRE REFERENCE CHART Wire Description Connector Name Connector Color Connector Type Position Wire Color Polarity Wire Location Camera Power ~ ~ 24 pin 24 Black (+) Reverse camera harness Ground ~ ~ 24 pin 21 White (-) Reverse camera harness Video + ~ ~ 24 pin 22 Red (+) Reverse camera harness Video - ~ ~ 24 pin 23 Shield (-) Reverse camera harness Wire Description Connector Name Connector Color Connector Type Position W
Toyota Highlander Without JBL 2013 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended. Reset the RR.
INSTALL GUIDE 2013-2014 Toyota Matrix RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro TO1 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY01-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Toyota Matrix 2013-2014 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Installation Instructions 3 Wiring Diagram 4 Radio Wire Reference Chart 5 Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware for your vehicle and that you carefully review the install guide.
Toyota Matrix 2013-2014 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on the next page from aftermarket radio main harness to the TO1 T-harness and match the wire functions. • Remove the factory radio. STEP 2 • If the vehicle is equipped with an OEM backup camera, connect the TO1 T-harness to the backup camera harness (see wire chart for details). STEP 3 • Identify if your vehicle has a 20 or 28 pin secondary connector.
Toyota Matrix 2013-2014 WIRING DIAGRAM without an Amplifier STEP 5 STEP 1 WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Matrix 2013-2014 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A N/A VS
Toyota Matrix 2013-2014 VEHICLE WIRE REFERENCE CHART REVERSE CAMERA NOT AVAILABLE / NOT PRESENT Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-TOY01-DS-IG-EN maestro.idatalink.
Toyota Matrix 2013-2014 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended. Reset the RR.
INSTALL GUIDE 2009-2012 Toyota Matrix With JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro TO1 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY01-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Toyota Matrix With JBL 2009-2012 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Toyota Matrix With JBL 2009-2012 INSTALLATION INSTRUCTIONS STEP 6 STEP 1 • Connect all the harnesses to the Maestro RR module then test your installation. • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on the next page from aftermarket radio main harness to the TO1 T-harness and match the wire functions. • Remove the factory radio.
Toyota Matrix With JBL 2009-2012 WIRING DIAGRAM with an Amplifier STEP 5 STEP 1 WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Matrix With JBL 2009-2012 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A
Toyota Matrix With JBL 2009-2012 VEHICLE WIRE REFERENCE CHART Wire Description Connector Name Connector Color Connector Type Position Wire Color Polarity Wire Location Camera Power ~ ~ 24 pin 11 Black (+) Reverse camera harness Ground ~ ~ 24 pin 23 Shield (-) Reverse camera harness Video + ~ ~ 24 pin 12 Red (+) Reverse camera harness Video - ~ ~ 24 pin 24 White (-) Reverse camera harness REVERSE CAMERA CONNECTOR (WIRE SIDE) 12 11 10 9 8 7 6 5 4 3 2 1 24 23
Toyota Matrix With JBL 2009-2012 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended. Reset the RR.
INSTALL GUIDE 2009-2012 Toyota Matrix Without JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro TO1 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY01-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Toyota Matrix Without JBL 2009-2012 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Toyota Matrix Without JBL 2009-2012 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on the next page from aftermarket radio main harness to the TO1 T-harness and match the wire functions. • Remove the factory radio. STEP 2 • If the vehicle is equipped with an OEM backup camera, connect the TO1 T-harness to the backup camera harness (see wire chart for details). STEP 3 • Identify if your vehicle has a 20 or 28 pin secondary connector.
Toyota Matrix Without JBL 2009-2012 WIRING DIAGRAM without an Amplifier STEP 5 STEP 1 WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Matrix Without JBL 2009-2012 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+) Yellow/Black Yellow/Black N⁄A
Toyota Matrix Without JBL 2009-2012 VEHICLE WIRE REFERENCE CHART Wire Description Connector Name Connector Color Connector Type Position Wire Color Polarity Wire Location Camera Power ~ ~ 24 pin 11 Black (+) Reverse camera harness Ground ~ ~ 24 pin 23 Shield (-) Reverse camera harness Video + ~ ~ 24 pin 12 Red (+) Reverse camera harness Video - ~ ~ 24 pin 24 White (-) Reverse camera harness REVERSE CAMERA CONNECTOR (WIRE SIDE) 12 11 10 9 8 7 6 5 4 3 2 1 24
Toyota Matrix Without JBL 2009-2012 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended. Reset the RR.
INSTALL GUIDE 2012-2015 Toyota Prius Base RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro TO1 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY01-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Toyota Prius Base 2012-2015 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Installation Instructions 3 Wiring Diagram 4 Radio Wire Reference Chart 5 Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware for your vehicle and that you carefully review the install guide.
Toyota Prius Base 2012-2015 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on the next page from aftermarket radio main harness to the TO1 T-harness and match the wire functions. • Remove the factory radio. STEP 2 • If the vehicle is equipped with an OEM backup camera, connect the TO1 T-harness to the backup camera harness (see wire chart for details). STEP 3 • Identify if your vehicle has a 20 or 28 pin secondary connector.
Toyota Prius Base 2012-2015 WIRING DIAGRAM without an Amplifier STEP 5 STEP 1 WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Prius Base 2012-2015 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A N/A
Toyota Prius Base 2012-2015 VEHICLE WIRE REFERENCE CHART Wire Description Connector Name Connector Color Connector Type Position Wire Color Polarity Wire Location Camera Power ~ ~ 16 pin 07 White (+) Reverse camera harness Ground ~ ~ 16 pin 15 Shield (-) Reverse camera harness Video + ~ ~ 16 pin 08 Red (+) Reverse camera harness Video - ~ ~ 16 pin 16 Black (-) Reverse camera harness REVERSE CAMERA CONNECTOR (WIRE SIDE) 8 7 6 5 4 3 2 1 16 15 14 13 12 11 10 9
Toyota Prius Base 2012-2015 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended. Reset the RR.
INSTALL GUIDE 2010-2011 Toyota Prius With JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro TO1 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY01-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Toyota Prius With JBL 2010-2011 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Installation Instructions 3 Wiring Diagram 4 Radio Wire Reference Chart 5 Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware for your vehicle and that you carefully review the install guide.
Toyota Prius With JBL 2010-2011 INSTALLATION INSTRUCTIONS STEP 6 STEP 1 • Connect all the harnesses to the Maestro RR module then test your installation. • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on the next page from aftermarket radio main harness to the TO1 T-harness and match the wire functions. • Remove the factory radio.
Toyota Prius With JBL 2010-2011 WIRING DIAGRAM with an Amplifier STEP 5 STEP 1 WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Prius With JBL 2010-2011 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A
Toyota Prius With JBL 2010-2011 VEHICLE WIRE REFERENCE CHART Wire Description Connector Name Connector Color Connector Type Position Wire Color Polarity Wire Location Camera Power ~ ~ 16 pin 07 White (+) Reverse camera harness Ground ~ ~ 16 pin 15 Shield (-) Reverse camera harness Video + ~ ~ 16 pin 08 Red (+) Reverse camera harness Video - ~ ~ 16 pin 16 Black (-) Reverse camera harness REVERSE CAMERA CONNECTOR (WIRE SIDE) 8 7 6 5 4 3 2 1 16 15 14 13 12 11 1
Toyota Prius With JBL 2010-2011 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended. Reset the RR.
INSTALL GUIDE 2010-2011 Toyota Prius Without JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro TO1 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY01-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Toyota Prius Without JBL 2010-2011 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Toyota Prius Without JBL 2010-2011 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on the next page from aftermarket radio main harness to the TO1 T-harness and match the wire functions. • Remove the factory radio. STEP 2 • If the vehicle is equipped with an OEM backup camera, connect the TO1 T-harness to the backup camera harness (see wire chart for details). STEP 3 • Identify if your vehicle has a 20 or 28 pin secondary connector.
Toyota Prius Without JBL 2010-2011 WIRING DIAGRAM without an Amplifier STEP 5 STEP 1 WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Prius Without JBL 2010-2011 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+) Yellow/Black Yellow/Black N⁄A N
Toyota Prius Without JBL 2010-2011 VEHICLE WIRE REFERENCE CHART Wire Description Connector Name Connector Color Connector Type Position Wire Color Polarity Wire Location Camera Power ~ ~ 16 pin 07 White (+) Reverse camera harness Ground ~ ~ 16 pin 15 Shield (-) Reverse camera harness Video + ~ ~ 16 pin 08 Red (+) Reverse camera harness Video - ~ ~ 16 pin 16 Black (-) Reverse camera harness REVERSE CAMERA CONNECTOR (WIRE SIDE) 8 7 6 5 4 3 2 1 16 15 14 13 12 1
Toyota Prius Without JBL 2010-2011 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended. Reset the RR.
INSTALL GUIDE 2012 Toyota Rav 4 RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro TO1 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY01-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Toyota Rav 4 2012 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Installation Instructions 3 Wiring Diagram 4 Radio Wire Reference Chart 5 Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware for your vehicle and that you carefully review the install guide.
Toyota Rav 4 2012 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on the next page from aftermarket radio main harness to the TO1 T-harness and match the wire functions. • Remove the factory radio. STEP 2 • If the vehicle is equipped with an OEM backup camera, connect the TO1 T-harness to the backup camera harness (see wire chart for details). STEP 3 • Identify if your vehicle has a 20 or 28 pin secondary connector.
Toyota Rav 4 2012 WIRING DIAGRAM without an Amplifier STEP 5 STEP 1 WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Rav 4 2012 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A N/A VSS (veh
Toyota Rav 4 2012 VEHICLE WIRE REFERENCE CHART REVERSE CAMERA NOT AVAILABLE / NOT PRESENT Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-TOY01-DS-IG-EN maestro.idatalink.
Toyota Rav 4 2012 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended. Reset the RR.
INSTALL GUIDE 2006-2011 Toyota Rav 4 With JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro TO1 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY01-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Toyota Rav 4 With JBL 2006-2011 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Installation Instructions 3 Wiring Diagram 4 Radio Wire Reference Chart 5 Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware for your vehicle and that you carefully review the install guide.
Toyota Rav 4 With JBL 2006-2011 INSTALLATION INSTRUCTIONS STEP 6 STEP 1 • Connect all the harnesses to the Maestro RR module then test your installation. • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on the next page from aftermarket radio main harness to the TO1 T-harness and match the wire functions. • Remove the factory radio.
Toyota Rav 4 With JBL 2006-2011 WIRING DIAGRAM with an Amplifier STEP 5 STEP 1 WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Rav 4 With JBL 2006-2011 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A
Toyota Rav 4 With JBL 2006-2011 VEHICLE WIRE REFERENCE CHART REVERSE CAMERA NOT AVAILABLE / NOT PRESENT Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-TOY01-DS-IG-EN maestro.idatalink.
Toyota Rav 4 With JBL 2006-2011 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended. Reset the RR.
INSTALL GUIDE 2006-2011 Toyota Rav 4 Without JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro TO1 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY01-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Toyota Rav 4 Without JBL 2006-2011 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Toyota Rav 4 Without JBL 2006-2011 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on the next page from aftermarket radio main harness to the TO1 T-harness and match the wire functions. • Remove the factory radio. STEP 2 • If the vehicle is equipped with an OEM backup camera, connect the TO1 T-harness to the backup camera harness (see wire chart for details). STEP 3 • Identify if your vehicle has a 20 or 28 pin secondary connector.
Toyota Rav 4 Without JBL 2006-2011 WIRING DIAGRAM without an Amplifier STEP 5 STEP 1 WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Rav 4 Without JBL 2006-2011 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+) Yellow/Black Yellow/Black N⁄A N
Toyota Rav 4 Without JBL 2006-2011 VEHICLE WIRE REFERENCE CHART REVERSE CAMERA NOT AVAILABLE / NOT PRESENT Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-TOY01-DS-IG-EN maestro.idatalink.
Toyota Rav 4 Without JBL 2006-2011 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended. Reset the RR.
INSTALL GUIDE 2008-2013 Toyota Sequoia With JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro TO1 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY01-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Toyota Sequoia With JBL 2008-2013 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Toyota Sequoia With JBL 2008-2013 INSTALLATION INSTRUCTIONS STEP 6 STEP 1 • Connect all the harnesses to the Maestro RR module then test your installation. • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on the next page from aftermarket radio main harness to the TO1 T-harness and match the wire functions. • Remove the factory radio.
Toyota Sequoia With JBL 2008-2013 WIRING DIAGRAM with an Amplifier STEP 5 STEP 1 WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Sequoia With JBL 2008-2013 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄
Toyota Sequoia With JBL 2008-2013 VEHICLE WIRE REFERENCE CHART Wire Description Connector Name Connector Color Connector Type Position Wire Color Polarity Wire Location Camera Power ~ ~ 24 pin 24 Black (+) Reverse camera harness Ground ~ ~ 24 pin 21 White (-) Reverse camera harness Video + ~ ~ 24 pin 22 Red (+) Reverse camera harness Video - ~ ~ 24 pin 23 Shield (-) Reverse camera harness Wire Description Connector Name Connector Color Connector Type Position Wi
Toyota Sequoia With JBL 2008-2013 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended. Reset the RR.
INSTALL GUIDE 2008-2013 Toyota Sequoia Without JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro TO1 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY01-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Toyota Sequoia Without JBL 2008-2013 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Toyota Sequoia Without JBL 2008-2013 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on the next page from aftermarket radio main harness to the TO1 T-harness and match the wire functions. • Remove the factory radio. STEP 2 • If the vehicle is equipped with an OEM backup camera, connect the TO1 T-harness to the backup camera harness (see wire chart for details). STEP 3 • Identify if your vehicle has a 20 or 28 pin secondary connector.
Toyota Sequoia Without JBL 2008-2013 WIRING DIAGRAM without an Amplifier STEP 5 STEP 1 WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Sequoia Without JBL 2008-2013 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+) Yellow/Black Yellow/Black N⁄A
Toyota Sequoia Without JBL 2008-2013 VEHICLE WIRE REFERENCE CHART Wire Description Connector Name Connector Color Connector Type Position Wire Color Polarity Wire Location Camera Power ~ ~ 20 pin 13 Black (+) Reverse camera harness Ground ~ ~ 20 pin 14 White (-) Reverse camera harness Video + ~ ~ 20 pin 11 Red (+) Reverse camera harness Video - ~ ~ 20 pin 12 Shield (-) Reverse camera harness REVERSE CAMERA CONNECTOR (WIRE SIDE) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
Toyota Sequoia Without JBL 2008-2013 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended. Reset the RR.
INSTALL GUIDE 2014-2018 Toyota Sequoia Without JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro TO1 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY01-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Toyota Sequoia Without JBL 2014-2018 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Toyota Sequoia Without JBL 2014-2018 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on the next page from aftermarket radio main harness to the TO1 T-harness and match the wire functions. • Remove the factory radio. STEP 2 • If the vehicle is equipped with an OEM backup camera, connect the TO1 T-harness to the backup camera harness (see wire chart for details). STEP 3 • Identify if your vehicle has a 20 or 28 pin secondary connector.
Toyota Sequoia Without JBL 2014-2018 WIRING DIAGRAM without an Amplifier STEP 5 STEP 1 WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Sequoia Without JBL 2014-2018 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+) Yellow/Black Yellow/Black N⁄A
Toyota Sequoia Without JBL 2014-2018 VEHICLE WIRE REFERENCE CHART Wire Description Connector Name Connector Color Connector Type Position Wire Color Polarity Wire Location Camera Power ~ ~ 24 pin 11 Black (+) Reverse camera harness Ground ~ ~ 24 pin 23 White (-) Reverse camera harness Video + ~ ~ 24 pin 12 Red (+) Reverse camera harness Video - ~ ~ 24 pin 24 Shield (-) Reverse camera harness REVERSE CAMERA CONNECTORS (WIRE SIDE) 12 11 10 9 8 7 6 5 4 3 2 1 2
Toyota Sequoia Without JBL 2014-2018 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended. Reset the RR.
INSTALL GUIDE 2007-2010 Toyota Sienna With JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro TO1 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY01-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Toyota Sienna With JBL 2007-2010 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Toyota Sienna With JBL 2007-2010 INSTALLATION INSTRUCTIONS STEP 6 STEP 1 • Connect all the harnesses to the Maestro RR module then test your installation. • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on the next page from aftermarket radio main harness to the TO1 T-harness and match the wire functions. • Remove the factory radio.
Toyota Sienna With JBL 2007-2010 WIRING DIAGRAM with an Amplifier STEP 5 STEP 1 WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Sienna With JBL 2007-2010 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A
Toyota Sienna With JBL 2007-2010 VEHICLE WIRE REFERENCE CHART Wire Description Connector Name Connector Color Connector Type Position Wire Color Polarity Wire Location Camera Power ~ ~ 24 pin 24 Red (+) Reverse camera harness Ground ~ ~ 24 pin 21 White (-) Reverse camera harness Video + ~ ~ 24 pin 22 Black (+) Reverse camera harness Video - ~ ~ 24 pin 23 Shield (-) Reverse camera harness REVERSE CAMERA CONNECTOR (WIRE SIDE) 1 2 3 4 5 6 7 8 9 10 11 12 13 14
Toyota Sienna With JBL 2007-2010 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended. Reset the RR.
INSTALL GUIDE 2011-2014 Toyota Sienna With JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro TO1 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY01-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Toyota Sienna With JBL 2011-2014 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Toyota Sienna With JBL 2011-2014 INSTALLATION INSTRUCTIONS STEP 6 STEP 1 • Connect all the harnesses to the Maestro RR module then test your installation. • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on the next page from aftermarket radio main harness to the TO1 T-harness and match the wire functions. • Remove the factory radio.
Toyota Sienna With JBL 2011-2014 WIRING DIAGRAM with an Amplifier STEP 5 STEP 1 WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Sienna With JBL 2011-2014 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A
Toyota Sienna With JBL 2011-2014 VEHICLE WIRE REFERENCE CHART Wire Description Connector Name Connector Color Connector Type Position Wire Color Polarity Wire Location Camera Power ~ ~ 30 pin 14 Red (+) Parking assist ECU, behind glovebox Ground ~ ~ ~ ~ ~ ~ ~ Video + ~ ~ 30 pin 12 Black (+) Parking assist ECU, behind glovebox Video - ~ ~ 30 pin 11 White (-) Parking assist ECU, behind glovebox PARKING ASSIST CONNECTOR (WIRE SIDE) 6 5 4 3 2 1 8 7 18 17 16 15
Toyota Sienna With JBL 2011-2014 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended. Reset the RR.
INSTALL GUIDE 2007-2010 Toyota Sienna Without JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro TO1 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY01-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Toyota Sienna Without JBL 2007-2010 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Toyota Sienna Without JBL 2007-2010 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on the next page from aftermarket radio main harness to the TO1 T-harness and match the wire functions. • Remove the factory radio. STEP 2 • If the vehicle is equipped with an OEM backup camera, connect the TO1 T-harness to the backup camera harness (see wire chart for details). STEP 3 • Identify if your vehicle has a 20 or 28 pin secondary connector.
Toyota Sienna Without JBL 2007-2010 WIRING DIAGRAM without an Amplifier STEP 5 STEP 1 WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Sienna Without JBL 2007-2010 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+) Yellow/Black Yellow/Black N⁄A
Toyota Sienna Without JBL 2007-2010 VEHICLE WIRE REFERENCE CHART REVERSE CAMERA NOT AVAILABLE / NOT PRESENT Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-TOY01-DS-IG-EN maestro.idatalink.
Toyota Sienna Without JBL 2007-2010 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended. Reset the RR.
INSTALL GUIDE 2011-2014 Toyota Sienna Without JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro TO1 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY01-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Toyota Sienna Without JBL 2011-2014 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Toyota Sienna Without JBL 2011-2014 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on the next page from aftermarket radio main harness to the TO1 T-harness and match the wire functions. • Remove the factory radio. STEP 2 • If the vehicle is equipped with an OEM backup camera, connect the TO1 T-harness to the backup camera harness (see wire chart for details). STEP 3 • Identify if your vehicle has a 20 or 28 pin secondary connector.
Toyota Sienna Without JBL 2011-2014 WIRING DIAGRAM without an Amplifier STEP 5 STEP 1 WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Sienna Without JBL 2011-2014 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+) Yellow/Black Yellow/Black N⁄A
Toyota Sienna Without JBL 2011-2014 VEHICLE WIRE REFERENCE CHART Wire Description Connector Name Connector Color Connector Type Position Wire Color Polarity Wire Location Camera Power ~ ~ 20 pin 13 Red (+) Reverse camera harness Ground ~ ~ 20 pin 14 Shield (-) Reverse camera harness Video + ~ ~ 20 pin 11 Black (+) Reverse camera harness Video - ~ ~ 20 pin 12 White (-) Reverse camera harness REVERSE CAMERA CONNECTOR (WIRE SIDE) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
Toyota Sienna Without JBL 2011-2014 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended. Reset the RR.
INSTALL GUIDE 2005-2011 Toyota Tacoma With JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro TO1 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY01-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Toyota Tacoma With JBL 2005-2011 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Toyota Tacoma With JBL 2005-2011 INSTALLATION INSTRUCTIONS STEP 6 STEP 1 • Connect all the harnesses to the Maestro RR module then test your installation. • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on the next page from aftermarket radio main harness to the TO1 T-harness and match the wire functions. • Remove the factory radio.
Toyota Tacoma With JBL 2005-2011 WIRING DIAGRAM with an Amplifier STEP 5 STEP 1 WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Tacoma With JBL 2005-2011 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A
Toyota Tacoma With JBL 2005-2011 VEHICLE WIRE REFERENCE CHART REVERSE CAMERA NOT AVAILABLE / NOT PRESENT Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-TOY01-DS-IG-EN maestro.idatalink.
Toyota Tacoma With JBL 2005-2011 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended. Reset the RR.
INSTALL GUIDE 2012-2013 Toyota Tacoma With JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro TO1 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY01-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Toyota Tacoma With JBL 2012-2013 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Toyota Tacoma With JBL 2012-2013 INSTALLATION INSTRUCTIONS STEP 6 STEP 1 • Connect all the harnesses to the Maestro RR module then test your installation. • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on the next page from aftermarket radio main harness to the TO1 T-harness and match the wire functions. • Remove the factory radio.
Toyota Tacoma With JBL 2012-2013 WIRING DIAGRAM with an Amplifier STEP 5 STEP 1 WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Tacoma With JBL 2012-2013 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A
Toyota Tacoma With JBL 2012-2013 VEHICLE WIRE REFERENCE CHART Wire Description Connector Name Connector Color Connector Type Position Wire Color Polarity Wire Location Camera Power ~ ~ 24 pin 11 Black (+) Reverse camera harness Ground ~ ~ 24 pin 23 Shield (-) Reverse camera harness Video + ~ ~ 24 pin 12 Red (+) Reverse camera harness Video - ~ ~ 24 pin 24 White (-) Reverse camera harness Wire Description Connector Name Connector Color Connector Type Position Wir
Toyota Tacoma With JBL 2012-2013 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended. Reset the RR.
INSTALL GUIDE 2014-2015 Toyota Tacoma With JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro TO1 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY01-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Toyota Tacoma With JBL 2014-2015 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Toyota Tacoma With JBL 2014-2015 INSTALLATION INSTRUCTIONS STEP 6 STEP 1 • Connect all the harnesses to the Maestro RR module then test your installation. • Unbox the aftermarket radio and locate its main harness. • Cut RCA wires from amp. adapter and connect them to matching wires of TO1 t-harness. • Connect the wires shown on the next page from aftermarket radio main harness to the TO1 T-harness and match the wire functions. • Remove the factory radio.
Toyota Tacoma With JBL 2014-2015 WIRING DIAGRAM with an Amplifier STEP 1 CUT RCA WIRES FROM AMP. ADAPTER. CONNECT THEM TO MATCHING WIRES OF TO1 T-HARNESS. WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Tacoma With JBL 2014-2015 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A
Toyota Tacoma With JBL 2014-2015 VEHICLE WIRE REFERENCE CHART Wire Description Connector Name Connector Color Connector Type Position Wire Color Polarity Wire Location Camera Power ~ ~ 24 pin 11 Black (+) Reverse camera harness Ground ~ ~ 24 pin 23 Shield (-) Reverse camera harness Video + ~ ~ 24 pin 12 Red (+) Reverse camera harness Video - ~ ~ 24 pin 24 White (-) Reverse camera harness Wire Description Connector Name Connector Color Connector Type Position Wir
Toyota Tacoma With JBL 2014-2015 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended. Reset the RR.
INSTALL GUIDE 2005-2011 Toyota Tacoma Without JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro TO1 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY01-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Toyota Tacoma Without JBL 2005-2011 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Toyota Tacoma Without JBL 2005-2011 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on the next page from aftermarket radio main harness to the TO1 T-harness and match the wire functions. • Remove the factory radio. STEP 2 • If the vehicle is equipped with an OEM backup camera, connect the TO1 T-harness to the backup camera harness (see wire chart for details). STEP 3 • Identify if your vehicle has a 20 or 28 pin secondary connector.
Toyota Tacoma Without JBL 2005-2011 WIRING DIAGRAM without an Amplifier STEP 5 STEP 1 WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Tacoma Without JBL 2005-2011 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+) Yellow/Black Yellow/Black N⁄A
Toyota Tacoma Without JBL 2005-2011 VEHICLE WIRE REFERENCE CHART REVERSE CAMERA NOT AVAILABLE / NOT PRESENT Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-TOY01-DS-IG-EN maestro.idatalink.
Toyota Tacoma Without JBL 2005-2011 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended. Reset the RR.
INSTALL GUIDE 2012-2015 Toyota Tacoma Without JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro TO1 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY01-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Toyota Tacoma Without JBL 2012-2015 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Toyota Tacoma Without JBL 2012-2015 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on the next page from aftermarket radio main harness to the TO1 T-harness and match the wire functions. • Remove the factory radio. STEP 2 • If the vehicle is equipped with an OEM backup camera, connect the TO1 T-harness to the backup camera harness (see wire chart for details). STEP 3 • Identify if your vehicle has a 20 or 28 pin secondary connector.
Toyota Tacoma Without JBL 2012-2015 WIRING DIAGRAM without an Amplifier STEP 5 STEP 1 WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Tacoma Without JBL 2012-2015 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+) Yellow/Black Yellow/Black N⁄A
Toyota Tacoma Without JBL 2012-2015 VEHICLE WIRE REFERENCE CHART Wire Description Connector Name Connector Color Connector Type Position Wire Color Polarity Wire Location Camera Power ~ ~ 24 pin 11 Black (+) Reverse camera harness Ground ~ ~ 24 pin 23 Shield (-) Reverse camera harness Video + ~ ~ 24 pin 12 Red (+) Reverse camera harness Video - ~ ~ 24 pin 24 White (-) Reverse camera harness Wire Description Connector Name Connector Color Connector Type Position
Toyota Tacoma Without JBL 2012-2015 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended. Reset the RR.
INSTALL GUIDE 2007-2013 Toyota Tundra With JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro TO1 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY01-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Toyota Tundra With JBL 2007-2013 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Toyota Tundra With JBL 2007-2013 INSTALLATION INSTRUCTIONS STEP 6 STEP 1 • Connect all the harnesses to the Maestro RR module then test your installation. • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on the next page from aftermarket radio main harness to the TO1 T-harness and match the wire functions. • Remove the factory radio.
Toyota Tundra With JBL 2007-2013 WIRING DIAGRAM with an Amplifier STEP 5 STEP 1 WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Tundra With JBL 2007-2013 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A
Toyota Tundra With JBL 2007-2013 VEHICLE WIRE REFERENCE CHART Wire Description Connector Name Connector Color Connector Type Position Wire Color Polarity Wire Location Camera Power ~ ~ 24 pin 24 Black (+) Reverse camera harness Ground ~ ~ 24 pin 21 Shield (-) Reverse camera harness Video + ~ ~ 24 pin 22 Red (+) Reverse camera harness Video - ~ ~ 24 pin 23 Shield (-) Reverse camera harness REVERSE CAMERA CONNECTOR (WIRE SIDE) 1 2 3 4 5 6 7 8 9 10 11 12 13 14
Toyota Tundra With JBL 2007-2013 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended. Reset the RR.
INSTALL GUIDE 2007-2013 Toyota Tundra Without JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro TO1 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY01-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Toyota Tundra Without JBL 2007-2013 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Toyota Tundra Without JBL 2007-2013 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on the next page from aftermarket radio main harness to the TO1 T-harness and match the wire functions. • Remove the factory radio. STEP 2 • If the vehicle is equipped with an OEM backup camera, connect the TO1 T-harness to the backup camera harness (see wire chart for details). STEP 3 • Identify if your vehicle has a 20 or 28 pin secondary connector.
Toyota Tundra Without JBL 2007-2013 WIRING DIAGRAM without an Amplifier STEP 5 STEP 1 WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Tundra Without JBL 2007-2013 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+) Yellow/Black Yellow/Black N⁄A
Toyota Tundra Without JBL 2007-2013 VEHICLE WIRE REFERENCE CHART Wire Description Connector Name Connector Color Connector Type Position Wire Color Polarity Wire Location Camera Power ~ ~ 20 pin 13 Black (+) Reverse camera harness Ground ~ ~ 20 pin 14 White (-) Reverse camera harness Video + ~ ~ 20 pin 11 Red (+) Reverse camera harness Video - ~ ~ 20 pin 12 Shield (-) Reverse camera harness REVERSE CAMERA CONNECTOR (WIRE SIDE) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
Toyota Tundra Without JBL 2007-2013 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended. Reset the RR.
INSTALL GUIDE 2009-2012 Toyota Venza With JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro TO1 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY01-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Toyota Venza With JBL 2009-2012 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Installation Instructions 3 Wiring Diagram 4 Radio Wire Reference Chart 5 Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware for your vehicle and that you carefully review the install guide.
Toyota Venza With JBL 2009-2012 INSTALLATION INSTRUCTIONS STEP 6 STEP 1 • Connect all the harnesses to the Maestro RR module then test your installation. • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on the next page from aftermarket radio main harness to the TO1 T-harness and match the wire functions. • Remove the factory radio.
Toyota Venza With JBL 2009-2012 WIRING DIAGRAM with an Amplifier STEP 5 STEP 1 WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Venza With JBL 2009-2012 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A
Toyota Venza With JBL 2009-2012 VEHICLE WIRE REFERENCE CHART Wire Description Connector Name Connector Color Connector Type Position Wire Color Polarity Wire Location Camera Power ~ ~ 24 pin 11 Black (+) Reverse camera harness Ground ~ ~ 24 pin 23 Shield (-) Reverse camera harness Video + ~ ~ 24 pin 12 Red (+) Reverse camera harness Video - ~ ~ 24 pin 24 White (-) Reverse camera harness Wire Description Connector Name Connector Color Connector Type Position Wire
Toyota Venza With JBL 2009-2012 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended. Reset the RR.
INSTALL GUIDE 2013-2014 Toyota Venza With JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro TO1 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY01-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Toyota Venza With JBL 2013-2014 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Installation Instructions 3 Wiring Diagram 4 Radio Wire Reference Chart 5 Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware for your vehicle and that you carefully review the install guide.
Toyota Venza With JBL 2013-2014 INSTALLATION INSTRUCTIONS STEP 6 STEP 1 • Connect all the harnesses to the Maestro RR module then test your installation. • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on the next page from aftermarket radio main harness to the TO1 T-harness and match the wire functions. • Remove the factory radio.
Toyota Venza With JBL 2013-2014 WIRING DIAGRAM with an Amplifier STEP 5 STEP 1 WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Venza With JBL 2013-2014 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A
Toyota Venza With JBL 2013-2014 VEHICLE WIRE REFERENCE CHART Wire Description Connector Name Connector Color Connector Type Position Wire Color Polarity Wire Location Camera Power ~ ~ 24 pin 11 Black (+) Reverse camera harness Ground ~ ~ 24 pin 23 Shield (-) Reverse camera harness Video + ~ ~ 24 pin 12 Red (+) Reverse camera harness Video - ~ ~ 24 pin 24 White (-) Reverse camera harness Wire Description Connector Name Connector Color Connector Type Position Wire
Toyota Venza With JBL 2013-2014 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended. Reset the RR.
INSTALL GUIDE 2009-2012 Toyota Venza Without JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro TO1 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY01-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Toyota Venza Without JBL 2009-2012 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Toyota Venza Without JBL 2009-2012 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on the next page from aftermarket radio main harness to the TO1 T-harness and match the wire functions. • Remove the factory radio. STEP 2 • If the vehicle is equipped with an OEM backup camera, connect the TO1 T-harness to the backup camera harness (see wire chart for details). STEP 3 • Identify if your vehicle has a 20 or 28 pin secondary connector.
Toyota Venza Without JBL 2009-2012 WIRING DIAGRAM without an Amplifier STEP 5 STEP 1 WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Venza Without JBL 2009-2012 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+) Yellow/Black Yellow/Black N⁄A N
Toyota Venza Without JBL 2009-2012 VEHICLE WIRE REFERENCE CHART REVERSE CAMERA NOT AVAILABLE / NOT PRESENT Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-TOY01-DS-IG-EN maestro.idatalink.
Toyota Venza Without JBL 2009-2012 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended. Reset the RR.
INSTALL GUIDE 2013-2014 Toyota Venza Without JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro TO1 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY01-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Toyota Venza Without JBL 2013-2014 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Toyota Venza Without JBL 2013-2014 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on the next page from aftermarket radio main harness to the TO1 T-harness and match the wire functions. • Remove the factory radio. STEP 2 • If the vehicle is equipped with an OEM backup camera, connect the TO1 T-harness to the backup camera harness (see wire chart for details). STEP 3 • Identify if your vehicle has a 20 or 28 pin secondary connector.
Toyota Venza Without JBL 2013-2014 WIRING DIAGRAM without an Amplifier STEP 5 STEP 1 WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Venza Without JBL 2013-2014 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+) Yellow/Black Yellow/Black N⁄A N
Toyota Venza Without JBL 2013-2014 VEHICLE WIRE REFERENCE CHART Wire Description Connector Name Connector Color Connector Type Position Wire Color Polarity Wire Location Camera Power ~ ~ 24 pin 11 Black (+) Reverse camera harness Ground ~ ~ 24 pin 23 Shield (-) Reverse camera harness Video + ~ ~ 24 pin 12 Red (+) Reverse camera harness Video - ~ ~ 24 pin 24 White (-) Reverse camera harness Wire Description Connector Name Connector Color Connector Type Position W
Toyota Venza Without JBL 2013-2014 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended. Reset the RR.
INSTALL GUIDE 2007-2011 Toyota Yaris RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro TO1 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY01-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Toyota Yaris 2007-2011 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Installation Instructions 3 Wiring Diagram 4 Radio Wire Reference Chart 5 Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware for your vehicle and that you carefully review the install guide.
Toyota Yaris 2007-2011 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on the next page from aftermarket radio main harness to the TO1 T-harness and match the wire functions. • Remove the factory radio. STEP 2 • If the vehicle is equipped with an OEM backup camera, connect the TO1 T-harness to the backup camera harness (see wire chart for details). STEP 3 • Identify if your vehicle has a 20 or 28 pin secondary connector.
Toyota Yaris 2007-2011 WIRING DIAGRAM without an Amplifier STEP 5 STEP 1 WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Yaris 2007-2011 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A N/A VSS
Toyota Yaris 2007-2011 VEHICLE WIRE REFERENCE CHART REVERSE CAMERA NOT AVAILABLE / NOT PRESENT Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-TOY01-DS-IG-EN maestro.idatalink.
Toyota Yaris 2007-2011 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended. Reset the RR.
INSTALL GUIDE 2012-2018 Toyota Yaris RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro TO1 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY01-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Toyota Yaris 2012-2018 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Installation Instructions 3 Wiring Diagram 4 Radio Wire Reference Chart 5 Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware for your vehicle and that you carefully review the install guide.
Toyota Yaris 2012-2018 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on the next page from aftermarket radio main harness to the TO1 T-harness and match the wire functions. • Remove the factory radio. STEP 2 • If the vehicle is equipped with an OEM backup camera, connect the TO1 T-harness to the backup camera harness (see wire chart for details). STEP 3 • Identify if your vehicle has a 20 or 28 pin secondary connector.
Toyota Yaris 2012-2018 WIRING DIAGRAM without an Amplifier STEP 5 STEP 1 WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Yaris 2012-2018 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A N/A VSS
Toyota Yaris 2012-2018 VEHICLE WIRE REFERENCE CHART REVERSE CAMERA NOT AVAILABLE / NOT PRESENT Automotive Data Solutions Inc. © 2019 ADS-RR(SR)-TOY01-DS-IG-EN maestro.idatalink.
Toyota Yaris 2012-2018 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended. Reset the RR.
