SELECT VEHICLE PRINT PAGES NEEDED HOW TO USE THIS INSTALL GUIDE 1 Open the Bookmarks menu and find your vehicle OR scroll down until you find the install guide for your vehicle. 2 Print only the pages for your vehicle using the advanced options in the Print menu. 3 Install your Maestro RR according to the guide for your vehicle. WARNING Pressing the printer icon or “quick printing” this document will print all of the guides in this compilation. NOTICE: Automotive Data Solutions Inc.
INSTALL GUIDE 2014-2019 Toyota 4 Runner With JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-TO2 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Toyota 4 Runner With JBL 2014-2019 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Toyota 4 Runner With JBL 2014-2019 INSTALLATION INSTRUCTIONS STEP 1 STEP 6 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on the next page from aftermarket radio main harness to the TO2 T-harness and match the wire functions. • Connect all the harnesses to the Maestro RR module then test your installation. • Remove the factory radio.
Toyota 4 Runner With JBL 2014-2019 WIRING DIAGRAM STEP 5 STEP 1 WHITE WHITE/BLACK GRAY GRAY/BLACK GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota 4 Runner With JBL 2014-2019 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+) Yellow/Black Yellow/Black N⁄A N
Toyota 4 Runner With JBL 2014-2019 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure 2 pin black connector is plugged into the 2 pin black of the 28 pin connector of the TO2 harness, not the OBD2. Reset the RR. Gauges work but are limited or data features are limited (turn signals, very limited gauge functionality).
INSTALL GUIDE 2014-2019 Toyota 4 Runner Without JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-TO2 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Toyota 4 Runner Without JBL 2014-2019 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Toyota 4 Runner Without JBL 2014-2019 INSTALLATION INSTRUCTIONS STEP 6 STEP 1 • Connect all the harnesses to the Maestro RR module then test your installation. • Unbox the aftermarket radio and locate its main harness. • Cut and remove the front speaker RCA connectors. • Connect the wires shown on the next page from aftermarket radio main harness to the TO2 T-harness and match the wire functions. • Remove the factory radio.
Toyota 4 Runner Without JBL 2014-2019 WIRING DIAGRAM STEP 5 STEP 1 PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT. CUT AND REMOVE THE SPEAKER WIRE RCA CONNECTORS WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota 4 Runner Without JBL 2014-2019 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+) Yellow/Black Yellow/Black N⁄A
Toyota 4 Runner Without JBL 2014-2019 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure 2 pin black connector is plugged into the 2 pin black of the 28 pin connector of the TO2 harness, not the OBD2. Reset the RR. Gauges work but are limited or data features are limited (turn signals, very limited gauge functionality).
INSTALL GUIDE 2015-2019 Toyota Avalon With JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-TO2 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Toyota Avalon With JBL 2015-2019 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Toyota Avalon With JBL 2015-2019 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on the next page from aftermarket radio main harness to the TO2 T-harness and match the wire functions. • Remove the factory radio. For vehicles with bird’s eye view: to retain this system, connect Yellow/Green wire from TO2 T-Harness to the radio’s Purple/White wire.
Toyota Avalon With JBL 2015-2019 WIRING DIAGRAM STEP 4 STEP 1 WHITE WHITE/BLACK GRAY GRAY/BLACK GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Avalon With JBL 2015-2019 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A
Toyota Avalon With JBL 2015-2019 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure 2 pin black connector is plugged into the 2 pin black of the 28 pin connector of the TO2 harness, not the OBD2. Reset the RR. Gauges work but are limited or data features are limited (turn signals, very limited gauge functionality). Ensure 2 pin black connector is plugged into the 2 pin black of the 28 pin connector of the TO2 harness, not the OBD2, then reset the RR.
INSTALL GUIDE 2013-2014 Toyota Avalon With NAV With JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-TO2 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Toyota Avalon With NAV With JBL 2013-2014 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Toyota Avalon With NAV With JBL 2013-2014 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on the next page from aftermarket radio main harness to the TO2 T-harness and match the wire functions. • Remove the factory radio. For vehicles with bird’s eye view: to retain this system, connect Yellow/Green wire from TO2 T-Harness to the radio’s Purple/White wire.
Toyota Avalon With NAV With JBL 2013-2014 WIRING DIAGRAM STEP 4 STEP 1 WHITE WHITE/BLACK GRAY GRAY/BLACK GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Avalon With NAV With JBL 2013-2014 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+) Yellow/Black Yellow/Black
Toyota Avalon With NAV With JBL 2013-2014 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure 2 pin black connector is plugged into the 2 pin black of the 28 pin connector of the TO2 harness, not the OBD2. Reset the RR. Gauges work but are limited or data features are limited (turn signals, very limited gauge functionality).
INSTALL GUIDE 2013-2014 Toyota Avalon With NAV Without JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-TO2 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Toyota Avalon With NAV Without JBL 2013-2014 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Toyota Avalon With NAV Without JBL 2013-2014 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Cut and remove the front speaker RCA connectors. • Connect the wires shown on the next page from aftermarket radio main harness to the TO2 T-harness and match the wire functions. • Remove the factory radio. For vehicles with bird’s eye view: to retain this system, connect Yellow/Green wire from TO2 T-Harness to the radio’s Purple/White wire.
Toyota Avalon With NAV Without JBL 2013-2014 WIRING DIAGRAM STEP 4 STEP 1 PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT. CUT AND REMOVE THE SPEAKER WIRE RCA CONNECTORS WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Avalon With NAV Without JBL 2013-2014 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+) Yellow/Black Yellow/Bla
Toyota Avalon With NAV Without JBL 2013-2014 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure 2 pin black connector is plugged into the 2 pin black of the 28 pin connector of the TO2 harness, not the OBD2. Reset the RR. Gauges work but are limited or data features are limited (turn signals, very limited gauge functionality).
INSTALL GUIDE 2015-2019 Toyota Avalon Without JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-TO2 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Toyota Avalon Without JBL 2015-2019 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Toyota Avalon Without JBL 2015-2019 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Cut and remove the front speaker RCA connectors. • Connect the wires shown on the next page from aftermarket radio main harness to the TO2 T-harness and match the wire functions. • Remove the factory radio. For vehicles with bird’s eye view: to retain this system, connect Yellow/Green wire from TO2 T-Harness to the radio’s Purple/White wire.
Toyota Avalon Without JBL 2015-2019 WIRING DIAGRAM STEP 4 STEP 1 PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT. CUT AND REMOVE THE SPEAKER WIRE RCA CONNECTORS WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Avalon Without JBL 2015-2019 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+) Yellow/Black Yellow/Black N⁄A
Toyota Avalon Without JBL 2015-2019 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure 2 pin black connector is plugged into the 2 pin black of the 28 pin connector of the TO2 harness, not the OBD2. Reset the RR. Gauges work but are limited or data features are limited (turn signals, very limited gauge functionality).
INSTALL GUIDE 2018 Toyota C-HR Without Apple Carplay or Android Auto RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-TO2 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Toyota C-HR Without Apple Carplay or Android Auto 2018 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Toyota C-HR Without Apple Carplay or Android Auto 2018 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Cut and remove the front speaker RCA connectors. • Connect the wires shown on the next page from aftermarket radio main harness to the TO2 T-harness and match the wire functions. • Remove the factory radio. For vehicles with bird’s eye view: to retain this system, connect Yellow/Green wire from TO2 T-Harness to the radio’s Purple/White wire.
Toyota C-HR Without Apple Carplay or Android Auto 2018 WIRING DIAGRAM STEP 4 STEP 1 PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT. CUT AND REMOVE THE SPEAKER WIRE RCA CONNECTORS WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota C-HR Without Apple Carplay or Android Auto 2018 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+) Yellow/Black
Toyota C-HR Without Apple Carplay or Android Auto 2018 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure 2 pin black connector is plugged into the 2 pin black of the 28 pin connector of the TO2 harness, not the OBD2. Reset the RR. Gauges work but are limited or data features are limited (turn signals, very limited gauge functionality).
INSTALL GUIDE 2012-2014 Toyota Camry With Factory 6.1 inch Screen RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-TO2 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Toyota Camry With Factory 6.1 inch Screen 2012-2014 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Toyota Camry With Factory 6.1 inch Screen 2012-2014 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Cut and remove the front speaker RCA connectors. • Connect the wires shown on the next page from aftermarket radio main harness to the TO2 T-harness and match the wire functions. • Remove the factory radio. For vehicles with bird’s eye view: to retain this system, connect Yellow/Green wire from TO2 T-Harness to the radio’s Purple/White wire.
Toyota Camry With Factory 6.1 inch Screen 2012-2014 WIRING DIAGRAM STEP 4 STEP 1 PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT. CUT AND REMOVE THE SPEAKER WIRE RCA CONNECTORS WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Camry With Factory 6.
Toyota Camry With Factory 6.1 inch Screen 2012-2014 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure 2 pin black connector is plugged into the 2 pin black of the 28 pin connector of the TO2 harness, not the OBD2. Reset the RR. Gauges work but are limited or data features are limited (turn signals, very limited gauge functionality).
INSTALL GUIDE 2012-2014 Toyota Camry With Factory 6.1 inch Screen and JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-TO2 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Toyota Camry With Factory 6.1 inch Screen and JBL 2012-2014 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Toyota Camry With Factory 6.1 inch Screen and JBL 2012-2014 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on the next page from aftermarket radio main harness to the TO2 T-harness and match the wire functions. • Remove the factory radio. For vehicles with bird’s eye view: to retain this system, connect Yellow/Green wire from TO2 T-Harness to the radio’s Purple/White wire.
Toyota Camry With Factory 6.1 inch Screen and JBL 2012-2014 WIRING DIAGRAM STEP 4 STEP 1 WHITE WHITE/BLACK GRAY GRAY/BLACK GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Camry With Factory 6.
Toyota Camry With Factory 6.1 inch Screen and JBL 2012-2014 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure 2 pin black connector is plugged into the 2 pin black of the 28 pin connector of the TO2 harness, not the OBD2. Reset the RR. Gauges work but are limited or data features are limited (turn signals, very limited gauge functionality).
INSTALL GUIDE 2012-2014 Toyota Camry With Factory Screen and HDD and JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-TO2 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Toyota Camry With Factory Screen and HDD and JBL 2012-2014 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Toyota Camry With Factory Screen and HDD and JBL 2012-2014 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on the next page from aftermarket radio main harness to the TO2 T-harness and match the wire functions. • Remove the factory radio. For vehicles with bird’s eye view: to retain this system, connect Yellow/Green wire from TO2 T-Harness to the radio’s Purple/White wire.
Toyota Camry With Factory Screen and HDD and JBL 2012-2014 WIRING DIAGRAM STEP 4 STEP 1 WHITE WHITE/BLACK GRAY GRAY/BLACK GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Camry With Factory Screen and HDD and JBL 2012-2014 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+) Yellow/Bla
Toyota Camry With Factory Screen and HDD and JBL 2012-2014 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure 2 pin black connector is plugged into the 2 pin black of the 28 pin connector of the TO2 harness, not the OBD2. Reset the RR. Gauges work but are limited or data features are limited (turn signals, very limited gauge functionality).
INSTALL GUIDE 2015-2017 Toyota Camry With JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-TO2 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Toyota Camry With JBL 2015-2017 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Installation Instructions 3 Wiring Diagram 4 Radio Wire Reference Chart 5 Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware for your vehicle and that you carefully review the install guide.
Toyota Camry With JBL 2015-2017 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on the next page from aftermarket radio main harness to the TO2 T-harness and match the wire functions. • Remove the factory radio. For vehicles with bird’s eye view: to retain this system, connect Yellow/Green wire from TO2 T-Harness to the radio’s Purple/White wire.
Toyota Camry With JBL 2015-2017 WIRING DIAGRAM STEP 4 STEP 1 WHITE WHITE/BLACK GRAY GRAY/BLACK GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Camry With JBL 2015-2017 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A
Toyota Camry With JBL 2015-2017 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure 2 pin black connector is plugged into the 2 pin black of the 28 pin connector of the TO2 harness, not the OBD2. Reset the RR. Gauges work but are limited or data features are limited (turn signals, very limited gauge functionality). Ensure 2 pin black connector is plugged into the 2 pin black of the 28 pin connector of the TO2 harness, not the OBD2, then reset the RR.
INSTALL GUIDE 2015-2017 Toyota Camry Without JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-TO2 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Toyota Camry Without JBL 2015-2017 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Toyota Camry Without JBL 2015-2017 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Cut and remove the front speaker RCA connectors. • Connect the wires shown on the next page from aftermarket radio main harness to the TO2 T-harness and match the wire functions. • Remove the factory radio. For vehicles with bird’s eye view: to retain this system, connect Yellow/Green wire from TO2 T-Harness to the radio’s Purple/White wire.
Toyota Camry Without JBL 2015-2017 WIRING DIAGRAM STEP 4 STEP 1 PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT. CUT AND REMOVE THE SPEAKER WIRE RCA CONNECTORS WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Camry Without JBL 2015-2017 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+) Yellow/Black Yellow/Black N⁄A N
Toyota Camry Without JBL 2015-2017 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure 2 pin black connector is plugged into the 2 pin black of the 28 pin connector of the TO2 harness, not the OBD2. Reset the RR. Gauges work but are limited or data features are limited (turn signals, very limited gauge functionality).
INSTALL GUIDE 2014-2019 Toyota Corolla With Factory 6.1 inch Screen RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-TO2 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Toyota Corolla With Factory 6.1 inch Screen 2014-2019 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Toyota Corolla With Factory 6.1 inch Screen 2014-2019 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Cut and remove the front speaker RCA connectors. • Connect the wires shown on the next page from aftermarket radio main harness to the TO2 T-harness and match the wire functions. • Remove the factory radio. For vehicles with bird’s eye view: to retain this system, connect Yellow/Green wire from TO2 T-Harness to the radio’s Purple/White wire.
Toyota Corolla With Factory 6.1 inch Screen 2014-2019 WIRING DIAGRAM STEP 4 STEP 1 PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT. CUT AND REMOVE THE SPEAKER WIRE RCA CONNECTORS WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Corolla With Factory 6.
Toyota Corolla With Factory 6.1 inch Screen 2014-2019 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure 2 pin black connector is plugged into the 2 pin black of the 28 pin connector of the TO2 harness, not the OBD2. Reset the RR. Gauges work but are limited or data features are limited (turn signals, very limited gauge functionality).
INSTALL GUIDE 2014-2019 Toyota Highlander With JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-TO2 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Toyota Highlander With JBL 2014-2019 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Toyota Highlander With JBL 2014-2019 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on the next page from aftermarket radio main harness to the TO2 T-harness and match the wire functions. • Remove the factory radio. For vehicles with bird’s eye view: to retain this system, connect Yellow/Green wire from TO2 T-Harness to the radio’s Purple/White wire.
Toyota Highlander With JBL 2014-2019 WIRING DIAGRAM STEP 4 STEP 1 WHITE WHITE/BLACK GRAY GRAY/BLACK GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Highlander With JBL 2014-2019 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+) Yellow/Black Yellow/Black N⁄A
Toyota Highlander With JBL 2014-2019 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure 2 pin black connector is plugged into the 2 pin black of the 28 pin connector of the TO2 harness, not the OBD2. Reset the RR. Gauges work but are limited or data features are limited (turn signals, very limited gauge functionality).
INSTALL GUIDE 2014-2019 Toyota Highlander Without JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-TO2 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Toyota Highlander Without JBL 2014-2019 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Toyota Highlander Without JBL 2014-2019 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Cut and remove the front speaker RCA connectors. • Connect the wires shown on the next page from aftermarket radio main harness to the TO2 T-harness and match the wire functions. • Remove the factory radio. For vehicles with bird’s eye view: to retain this system, connect Yellow/Green wire from TO2 T-Harness to the radio’s Purple/White wire.
Toyota Highlander Without JBL 2014-2019 WIRING DIAGRAM STEP 4 STEP 1 PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT. CUT AND REMOVE THE SPEAKER WIRE RCA CONNECTORS WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Highlander Without JBL 2014-2019 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+) Yellow/Black Yellow/Black N
Toyota Highlander Without JBL 2014-2019 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure 2 pin black connector is plugged into the 2 pin black of the 28 pin connector of the TO2 harness, not the OBD2. Reset the RR. Gauges work but are limited or data features are limited (turn signals, very limited gauge functionality).
INSTALL GUIDE 2016-2019 Toyota Prius Base RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-TO2 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Toyota Prius Base 2016-2019 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Installation Instructions 3 Wiring Diagram 4 Radio Wire Reference Chart 5 Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware for your vehicle and that you carefully review the install guide.
Toyota Prius Base 2016-2019 INSTALLATION INSTRUCTIONS STEP 6 STEP 1 • Connect all the harnesses to the Maestro RR module then test your installation. • Unbox the aftermarket radio and locate its main harness. • Cut and remove the front speaker RCA connectors. • Connect the wires shown on the next page from aftermarket radio main harness to the TO2 T-harness and match the wire functions. • Remove the factory radio.
Toyota Prius Base 2016-2019 WIRING DIAGRAM STEP 5 STEP 1 PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT. CUT AND REMOVE THE SPEAKER WIRE RCA CONNECTORS WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Prius Base 2016-2019 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A N/A
Toyota Prius Base 2016-2019 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure 2 pin black connector is plugged into the 2 pin black of the 28 pin connector of the TO2 harness, not the OBD2. Reset the RR. Gauges work but are limited or data features are limited (turn signals, very limited gauge functionality). Ensure 2 pin black connector is plugged into the 2 pin black of the 28 pin connector of the TO2 harness, not the OBD2, then reset the RR.
INSTALL GUIDE 2015-2019 Toyota Prius C With JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-TO2 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Toyota Prius C With JBL 2015-2019 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Toyota Prius C With JBL 2015-2019 INSTALLATION INSTRUCTIONS STEP 1 STEP 6 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on the next page from aftermarket radio main harness to the TO2 T-harness and match the wire functions. • Connect all the harnesses to the Maestro RR module then test your installation. • Remove the factory radio.
Toyota Prius C With JBL 2015-2019 WIRING DIAGRAM STEP 5 STEP 1 WHITE WHITE/BLACK GRAY GRAY/BLACK GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Prius C With JBL 2015-2019 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄
Toyota Prius C With JBL 2015-2019 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure 2 pin black connector is plugged into the 2 pin black of the 28 pin connector of the TO2 harness, not the OBD2. Reset the RR. Gauges work but are limited or data features are limited (turn signals, very limited gauge functionality).
INSTALL GUIDE 2012-2014 Toyota Prius C Without JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-TO2 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Toyota Prius C Without JBL 2012-2014 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Toyota Prius C Without JBL 2012-2014 INSTALLATION INSTRUCTIONS STEP 6 STEP 1 • Connect all the harnesses to the Maestro RR module then test your installation. • Unbox the aftermarket radio and locate its main harness. • Cut and remove the front speaker RCA connectors. • Connect the wires shown on the next page from aftermarket radio main harness to the TO2 T-harness and match the wire functions. • Remove the factory radio.
Toyota Prius C Without JBL 2012-2014 WIRING DIAGRAM STEP 5 STEP 1 PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT. CUT AND REMOVE THE SPEAKER WIRE RCA CONNECTORS WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Prius C Without JBL 2012-2014 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+) Yellow/Black Yellow/Black N⁄A
Toyota Prius C Without JBL 2012-2014 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure 2 pin black connector is plugged into the 2 pin black of the 28 pin connector of the TO2 harness, not the OBD2. Reset the RR. Gauges work but are limited or data features are limited (turn signals, very limited gauge functionality).
INSTALL GUIDE 2015-2019 Toyota Prius C Without JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-TO2 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Toyota Prius C Without JBL 2015-2019 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Toyota Prius C Without JBL 2015-2019 INSTALLATION INSTRUCTIONS STEP 6 STEP 1 • Connect all the harnesses to the Maestro RR module then test your installation. • Unbox the aftermarket radio and locate its main harness. • Cut and remove the front speaker RCA connectors. • Connect the wires shown on the next page from aftermarket radio main harness to the TO2 T-harness and match the wire functions. • Remove the factory radio.
Toyota Prius C Without JBL 2015-2019 WIRING DIAGRAM STEP 5 STEP 1 PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT. CUT AND REMOVE THE SPEAKER WIRE RCA CONNECTORS WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Prius C Without JBL 2015-2019 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+) Yellow/Black Yellow/Black N⁄A
Toyota Prius C Without JBL 2015-2019 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure 2 pin black connector is plugged into the 2 pin black of the 28 pin connector of the TO2 harness, not the OBD2. Reset the RR. Gauges work but are limited or data features are limited (turn signals, very limited gauge functionality).
INSTALL GUIDE 2012-2014 Toyota Prius V With JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-TO2 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Toyota Prius V With JBL 2012-2014 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Toyota Prius V With JBL 2012-2014 INSTALLATION INSTRUCTIONS STEP 1 STEP 6 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on the next page from aftermarket radio main harness to the TO2 T-harness and match the wire functions. • Connect all the harnesses to the Maestro RR module then test your installation. • Remove the factory radio.
Toyota Prius V With JBL 2012-2014 WIRING DIAGRAM STEP 5 STEP 1 WHITE WHITE/BLACK GRAY GRAY/BLACK GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Prius V With JBL 2012-2014 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄
Toyota Prius V With JBL 2012-2014 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure 2 pin black connector is plugged into the 2 pin black of the 28 pin connector of the TO2 harness, not the OBD2. Reset the RR. Gauges work but are limited or data features are limited (turn signals, very limited gauge functionality).
INSTALL GUIDE 2015-2017 Toyota Prius V With JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-TO2 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Toyota Prius V With JBL 2015-2017 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Toyota Prius V With JBL 2015-2017 INSTALLATION INSTRUCTIONS STEP 1 STEP 6 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on the next page from aftermarket radio main harness to the TO2 T-harness and match the wire functions. • Connect all the harnesses to the Maestro RR module then test your installation. • Remove the factory radio.
Toyota Prius V With JBL 2015-2017 WIRING DIAGRAM STEP 5 STEP 1 WHITE WHITE/BLACK GRAY GRAY/BLACK GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Prius V With JBL 2015-2017 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄
Toyota Prius V With JBL 2015-2017 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure 2 pin black connector is plugged into the 2 pin black of the 28 pin connector of the TO2 harness, not the OBD2. Reset the RR. Gauges work but are limited or data features are limited (turn signals, very limited gauge functionality).
INSTALL GUIDE 2012-2014 Toyota Prius V Without JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-TO2 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Toyota Prius V Without JBL 2012-2014 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Toyota Prius V Without JBL 2012-2014 INSTALLATION INSTRUCTIONS STEP 6 STEP 1 • Connect all the harnesses to the Maestro RR module then test your installation. • Unbox the aftermarket radio and locate its main harness. • Cut and remove the front speaker RCA connectors. • Connect the wires shown on the next page from aftermarket radio main harness to the TO2 T-harness and match the wire functions. • Remove the factory radio.
Toyota Prius V Without JBL 2012-2014 WIRING DIAGRAM STEP 5 STEP 1 PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT. CUT AND REMOVE THE SPEAKER WIRE RCA CONNECTORS WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Prius V Without JBL 2012-2014 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+) Yellow/Black Yellow/Black N⁄A
Toyota Prius V Without JBL 2012-2014 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure 2 pin black connector is plugged into the 2 pin black of the 28 pin connector of the TO2 harness, not the OBD2. Reset the RR. Gauges work but are limited or data features are limited (turn signals, very limited gauge functionality).
INSTALL GUIDE 2015-2017 Toyota Prius V Without JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-TO2 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Toyota Prius V Without JBL 2015-2017 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Toyota Prius V Without JBL 2015-2017 INSTALLATION INSTRUCTIONS STEP 6 STEP 1 • Connect all the harnesses to the Maestro RR module then test your installation. • Unbox the aftermarket radio and locate its main harness. • Cut and remove the front speaker RCA connectors. • Connect the wires shown on the next page from aftermarket radio main harness to the TO2 T-harness and match the wire functions. • Remove the factory radio.
Toyota Prius V Without JBL 2015-2017 WIRING DIAGRAM STEP 5 STEP 1 PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT. CUT AND REMOVE THE SPEAKER WIRE RCA CONNECTORS WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Prius V Without JBL 2015-2017 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+) Yellow/Black Yellow/Black N⁄A
Toyota Prius V Without JBL 2015-2017 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure 2 pin black connector is plugged into the 2 pin black of the 28 pin connector of the TO2 harness, not the OBD2. Reset the RR. Gauges work but are limited or data features are limited (turn signals, very limited gauge functionality).
INSTALL GUIDE 2012-2014 Toyota Prius With JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-TO2 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Toyota Prius With JBL 2012-2014 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Installation Instructions 3 Wiring Diagram 4 Radio Wire Reference Chart 5 Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware for your vehicle and that you carefully review the install guide.
Toyota Prius With JBL 2012-2014 INSTALLATION INSTRUCTIONS STEP 1 STEP 6 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on the next page from aftermarket radio main harness to the TO2 T-harness and match the wire functions. • Connect all the harnesses to the Maestro RR module then test your installation. • Remove the factory radio. For vehicles with bird’s eye view: to retain this system, connect Yellow/Green wire from TO2 T-Harness to the radio’s Purple/White wire.
Toyota Prius With JBL 2012-2014 WIRING DIAGRAM STEP 5 STEP 1 WHITE WHITE/BLACK GRAY GRAY/BLACK GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Prius With JBL 2012-2014 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A
Toyota Prius With JBL 2012-2014 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure 2 pin black connector is plugged into the 2 pin black of the 28 pin connector of the TO2 harness, not the OBD2. Reset the RR. Gauges work but are limited or data features are limited (turn signals, very limited gauge functionality). Ensure 2 pin black connector is plugged into the 2 pin black of the 28 pin connector of the TO2 harness, not the OBD2, then reset the RR.
INSTALL GUIDE 2015-2019 Toyota Prius With JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-TO2 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Toyota Prius With JBL 2015-2019 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Installation Instructions 3 Wiring Diagram 4 Radio Wire Reference Chart 5 Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware for your vehicle and that you carefully review the install guide.
Toyota Prius With JBL 2015-2019 INSTALLATION INSTRUCTIONS STEP 1 STEP 6 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on the next page from aftermarket radio main harness to the TO2 T-harness and match the wire functions. • Connect all the harnesses to the Maestro RR module then test your installation. • Remove the factory radio. For vehicles with bird’s eye view: to retain this system, connect Yellow/Green wire from TO2 T-Harness to the radio’s Purple/White wire.
Toyota Prius With JBL 2015-2019 WIRING DIAGRAM STEP 5 STEP 1 WHITE WHITE/BLACK GRAY GRAY/BLACK GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Prius With JBL 2015-2019 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A
Toyota Prius With JBL 2015-2019 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure 2 pin black connector is plugged into the 2 pin black of the 28 pin connector of the TO2 harness, not the OBD2. Reset the RR. Gauges work but are limited or data features are limited (turn signals, very limited gauge functionality). Ensure 2 pin black connector is plugged into the 2 pin black of the 28 pin connector of the TO2 harness, not the OBD2, then reset the RR.
INSTALL GUIDE 2012-2014 Toyota Prius With Nav Without JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-TO2 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Toyota Prius With Nav Without JBL 2012-2014 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Toyota Prius With Nav Without JBL 2012-2014 INSTALLATION INSTRUCTIONS STEP 6 STEP 1 • Connect all the harnesses to the Maestro RR module then test your installation. • Unbox the aftermarket radio and locate its main harness. • Cut and remove the front speaker RCA connectors. • Connect the wires shown on the next page from aftermarket radio main harness to the TO2 T-harness and match the wire functions. • Remove the factory radio.
Toyota Prius With Nav Without JBL 2012-2014 WIRING DIAGRAM STEP 5 STEP 1 PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT. CUT AND REMOVE THE SPEAKER WIRE RCA CONNECTORS WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Prius With Nav Without JBL 2012-2014 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+) Yellow/Black Yellow/Blac
Toyota Prius With Nav Without JBL 2012-2014 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure 2 pin black connector is plugged into the 2 pin black of the 28 pin connector of the TO2 harness, not the OBD2. Reset the RR. Gauges work but are limited or data features are limited (turn signals, very limited gauge functionality).
INSTALL GUIDE 2015-2019 Toyota Prius With Nav Without JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-TO2 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Toyota Prius With Nav Without JBL 2015-2019 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Toyota Prius With Nav Without JBL 2015-2019 INSTALLATION INSTRUCTIONS STEP 6 STEP 1 • Connect all the harnesses to the Maestro RR module then test your installation. • Unbox the aftermarket radio and locate its main harness. • Cut and remove the front speaker RCA connectors. • Connect the wires shown on the next page from aftermarket radio main harness to the TO2 T-harness and match the wire functions. • Remove the factory radio.
Toyota Prius With Nav Without JBL 2015-2019 WIRING DIAGRAM STEP 5 STEP 1 PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT. CUT AND REMOVE THE SPEAKER WIRE RCA CONNECTORS WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Prius With Nav Without JBL 2015-2019 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+) Yellow/Black Yellow/Blac
Toyota Prius With Nav Without JBL 2015-2019 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure 2 pin black connector is plugged into the 2 pin black of the 28 pin connector of the TO2 harness, not the OBD2. Reset the RR. Gauges work but are limited or data features are limited (turn signals, very limited gauge functionality).
INSTALL GUIDE 2013-2018 Toyota Rav 4 With Factory 6.1 inch Screen RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-TO2 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Toyota Rav 4 With Factory 6.1 inch Screen 2013-2018 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Toyota Rav 4 With Factory 6.1 inch Screen 2013-2018 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Cut and remove the front speaker RCA connectors. • Connect the wires shown on the next page from aftermarket radio main harness to the TO2 T-harness and match the wire functions. • Remove the factory radio. For vehicles with bird’s eye view: to retain this system, connect Yellow/Green wire from TO2 T-Harness to the radio’s Purple/White wire.
Toyota Rav 4 With Factory 6.1 inch Screen 2013-2018 WIRING DIAGRAM STEP 4 STEP 1 PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT. CUT AND REMOVE THE SPEAKER WIRE RCA CONNECTORS WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Rav 4 With Factory 6.
Toyota Rav 4 With Factory 6.1 inch Screen 2013-2018 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure 2 pin black connector is plugged into the 2 pin black of the 28 pin connector of the TO2 harness, not the OBD2. Reset the RR. Gauges work but are limited or data features are limited (turn signals, very limited gauge functionality).
INSTALL GUIDE 2013-2018 Toyota Rav 4 With Factory 6.1 inch Screen and JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-TO2 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Toyota Rav 4 With Factory 6.1 inch Screen and JBL 2013-2018 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Toyota Rav 4 With Factory 6.1 inch Screen and JBL 2013-2018 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on the next page from aftermarket radio main harness to the TO2 T-harness and match the wire functions. • Remove the factory radio. For vehicles with bird’s eye view: to retain this system, connect Yellow/Green wire from TO2 T-Harness to the radio’s Purple/White wire.
Toyota Rav 4 With Factory 6.1 inch Screen and JBL 2013-2018 WIRING DIAGRAM STEP 4 STEP 1 WHITE WHITE/BLACK GRAY GRAY/BLACK GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Rav 4 With Factory 6.
Toyota Rav 4 With Factory 6.1 inch Screen and JBL 2013-2018 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure 2 pin black connector is plugged into the 2 pin black of the 28 pin connector of the TO2 harness, not the OBD2. Reset the RR. Gauges work but are limited or data features are limited (turn signals, very limited gauge functionality).
INSTALL GUIDE 2014-2017 Toyota Sequoia With JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-TO2 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Toyota Sequoia With JBL 2014-2017 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Toyota Sequoia With JBL 2014-2017 INSTALLATION INSTRUCTIONS STEP 1 plug the camera into Camera 1 on the radio. This is the only camera input that allows camera control through the touchscreen. • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on the next page from aftermarket radio main harness to the TO2 T-harness and match the wire functions. STEP 6 • Remove the factory radio.
Toyota Sequoia With JBL 2014-2017 WIRING DIAGRAM STEP 5 STEP 1 WHITE WHITE/BLACK GRAY GRAY/BLACK GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Sequoia With JBL 2014-2017 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄
Toyota Sequoia With JBL 2014-2017 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBD2 connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended. Reset the RR.
INSTALL GUIDE 2018-2019 Toyota Sequoia With JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-TO2 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Toyota Sequoia With JBL 2018-2019 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Toyota Sequoia With JBL 2018-2019 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on the next page from aftermarket radio main harness to the TO2 T-harness and match the wire functions. • Remove the factory radio. For vehicles with bird’s eye view: to retain this system, connect Yellow/Green wire from TO2 T-Harness to the radio’s Purple/White wire.
Toyota Sequoia With JBL 2018-2019 WIRING DIAGRAM STEP 4 STEP 1 WHITE WHITE/BLACK GRAY GRAY/BLACK GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Sequoia With JBL 2018-2019 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄
Toyota Sequoia With JBL 2018-2019 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure 2 pin black connector is plugged into the 2 pin black of the 28 pin connector of the TO2 harness, not the OBD2. Reset the RR. Gauges work but are limited or data features are limited (turn signals, very limited gauge functionality).
INSTALL GUIDE 2015-2019 Toyota Sienna With JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-TO2 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Toyota Sienna With JBL 2015-2019 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Toyota Sienna With JBL 2015-2019 INSTALLATION INSTRUCTIONS STEP 1 STEP 6 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on the next page from aftermarket radio main harness to the TO2 T-harness and match the wire functions. • Connect all the harnesses to the Maestro RR module then test your installation. • Remove the factory radio.
Toyota Sienna With JBL 2015-2019 WIRING DIAGRAM STEP 5 STEP 1 WHITE WHITE/BLACK GRAY GRAY/BLACK GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Sienna With JBL 2015-2019 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A
Toyota Sienna With JBL 2015-2019 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure 2 pin black connector is plugged into the 2 pin black of the 28 pin connector of the TO2 harness, not the OBD2. Reset the RR. Gauges work but are limited or data features are limited (turn signals, very limited gauge functionality). Ensure 2 pin black connector is plugged into the 2 pin black of the 28 pin connector of the TO2 harness, not the OBD2, then reset the RR.
INSTALL GUIDE 2015-2019 Toyota Sienna Without JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-TO2 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Toyota Sienna Without JBL 2015-2019 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Toyota Sienna Without JBL 2015-2019 INSTALLATION INSTRUCTIONS STEP 6 STEP 1 • Connect all the harnesses to the Maestro RR module then test your installation. • Unbox the aftermarket radio and locate its main harness. • Cut and remove the front speaker RCA connectors. • Connect the wires shown on the next page from aftermarket radio main harness to the TO2 T-harness and match the wire functions. • Remove the factory radio.
Toyota Sienna Without JBL 2015-2019 WIRING DIAGRAM STEP 5 STEP 1 PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT. CUT AND REMOVE THE SPEAKER WIRE RCA CONNECTORS WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Sienna Without JBL 2015-2019 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+) Yellow/Black Yellow/Black N⁄A
Toyota Sienna Without JBL 2015-2019 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure 2 pin black connector is plugged into the 2 pin black of the 28 pin connector of the TO2 harness, not the OBD2. Reset the RR. Gauges work but are limited or data features are limited (turn signals, very limited gauge functionality).
INSTALL GUIDE 2016-2019 Toyota Tacoma With JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-TO2 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Toyota Tacoma With JBL 2016-2019 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Toyota Tacoma With JBL 2016-2019 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on the next page from aftermarket radio main harness to the TO2 T-harness and match the wire functions. • Remove the factory radio. For vehicles with bird’s eye view: to retain this system, connect Yellow/Green wire from TO2 T-Harness to the radio’s Purple/White wire.
Toyota Tacoma With JBL 2016-2019 WIRING DIAGRAM STEP 4 STEP 1 WHITE WHITE/BLACK GRAY GRAY/BLACK GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Tacoma With JBL 2016-2019 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A
Toyota Tacoma With JBL 2016-2019 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure 2 pin black connector is plugged into the 2 pin black of the 28 pin connector of the TO2 harness, not the OBD2. Reset the RR. Gauges work but are limited or data features are limited (turn signals, very limited gauge functionality). Ensure 2 pin black connector is plugged into the 2 pin black of the 28 pin connector of the TO2 harness, not the OBD2, then reset the RR.
INSTALL GUIDE 2016-2019 Toyota Tacoma Without JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-TO2 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Toyota Tacoma Without JBL 2016-2019 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Toyota Tacoma Without JBL 2016-2019 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Cut and remove the front speaker RCA connectors. • Connect the wires shown on the next page from aftermarket radio main harness to the TO2 T-harness and match the wire functions. • Remove the factory radio. For vehicles with bird’s eye view: to retain this system, connect Yellow/Green wire from TO2 T-Harness to the radio’s Purple/White wire.
Toyota Tacoma Without JBL 2016-2019 WIRING DIAGRAM STEP 4 STEP 1 PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT. CUT AND REMOVE THE SPEAKER WIRE RCA CONNECTORS WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Tacoma Without JBL 2016-2019 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+) Yellow/Black Yellow/Black N⁄A
Toyota Tacoma Without JBL 2016-2019 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure 2 pin black connector is plugged into the 2 pin black of the 28 pin connector of the TO2 harness, not the OBD2. Reset the RR. Gauges work but are limited or data features are limited (turn signals, very limited gauge functionality).
INSTALL GUIDE 2014-2019 Toyota Tundra With JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-TO2 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Toyota Tundra With JBL 2014-2019 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Toyota Tundra With JBL 2014-2019 INSTALLATION INSTRUCTIONS STEP 1 STEP 6 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on the next page from aftermarket radio main harness to the TO2 T-harness and match the wire functions. • Connect all the harnesses to the Maestro RR module then test your installation. • Remove the factory radio.
Toyota Tundra With JBL 2014-2019 WIRING DIAGRAM STEP 5 STEP 1 WHITE WHITE/BLACK GRAY GRAY/BLACK GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Tundra With JBL 2014-2019 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A
Toyota Tundra With JBL 2014-2019 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure 2 pin black connector is plugged into the 2 pin black of the 28 pin connector of the TO2 harness, not the OBD2. Reset the RR. Gauges work but are limited or data features are limited (turn signals, very limited gauge functionality). Ensure 2 pin black connector is plugged into the 2 pin black of the 28 pin connector of the TO2 harness, not the OBD2, then reset the RR.
INSTALL GUIDE 2014-2019 Toyota Tundra With non-JBL AMP RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-TO2 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Toyota Tundra With non-JBL AMP 2014-2019 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Toyota Tundra With non-JBL AMP 2014-2019 INSTALLATION INSTRUCTIONS STEP 6 STEP 1 • Connect all the harnesses to the Maestro RR module then test your installation. • Unbox the aftermarket radio and locate its main harness. • Cut and remove the front speaker RCA connectors. • Connect the wires shown on the next page from aftermarket radio main harness to the TO2 T-harness and match the wire functions. • Remove the factory radio.
Toyota Tundra With non-JBL AMP 2014-2019 WIRING DIAGRAM STEP 5 STEP 1 PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT. CUT AND REMOVE THE SPEAKER WIRE RCA CONNECTORS WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Tundra With non-JBL AMP 2014-2019 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+) Yellow/Black Yellow/Black
Toyota Tundra With non-JBL AMP 2014-2019 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure 2 pin black connector is plugged into the 2 pin black of the 28 pin connector of the TO2 harness, not the OBD2. Reset the RR. Gauges work but are limited or data features are limited (turn signals, very limited gauge functionality).
INSTALL GUIDE 2014-2019 Toyota Tundra Without JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-TO2 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Toyota Tundra Without JBL 2014-2019 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Toyota Tundra Without JBL 2014-2019 INSTALLATION INSTRUCTIONS STEP 6 STEP 1 • Connect all the harnesses to the Maestro RR module then test your installation. • Unbox the aftermarket radio and locate its main harness. • Cut and remove the front speaker RCA connectors. • Connect the wires shown on the next page from aftermarket radio main harness to the TO2 T-harness and match the wire functions. • Remove the factory radio.
Toyota Tundra Without JBL 2014-2019 WIRING DIAGRAM STEP 5 STEP 1 PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT. CUT AND REMOVE THE SPEAKER WIRE RCA CONNECTORS WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Tundra Without JBL 2014-2019 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+) Yellow/Black Yellow/Black N⁄A
Toyota Tundra Without JBL 2014-2019 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure 2 pin black connector is plugged into the 2 pin black of the 28 pin connector of the TO2 harness, not the OBD2. Reset the RR. Gauges work but are limited or data features are limited (turn signals, very limited gauge functionality).
INSTALL GUIDE 2015-2016 Toyota Venza With JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-TO2 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Toyota Venza With JBL 2015-2016 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Installation Instructions 3 Wiring Diagram 4 Radio Wire Reference Chart 5 Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware for your vehicle and that you carefully review the install guide.
Toyota Venza With JBL 2015-2016 INSTALLATION INSTRUCTIONS STEP 1 STEP 6 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on the next page from aftermarket radio main harness to the TO2 T-harness and match the wire functions. • Connect all the harnesses to the Maestro RR module then test your installation. • Remove the factory radio. For vehicles with bird’s eye view: to retain this system, connect Yellow/Green wire from TO2 T-Harness to the radio’s Purple/White wire.
Toyota Venza With JBL 2015-2016 WIRING DIAGRAM STEP 5 STEP 1 WHITE WHITE/BLACK GRAY GRAY/BLACK GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Venza With JBL 2015-2016 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A
Toyota Venza With JBL 2015-2016 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure 2 pin black connector is plugged into the 2 pin black of the 28 pin connector of the TO2 harness, not the OBD2. Reset the RR. Gauges work but are limited or data features are limited (turn signals, very limited gauge functionality). Ensure 2 pin black connector is plugged into the 2 pin black of the 28 pin connector of the TO2 harness, not the OBD2, then reset the RR.
INSTALL GUIDE 2013-2014 Toyota Venza With JBL and Nav RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-TO2 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Toyota Venza With JBL and Nav 2013-2014 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Toyota Venza With JBL and Nav 2013-2014 INSTALLATION INSTRUCTIONS STEP 1 STEP 6 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on the next page from aftermarket radio main harness to the TO2 T-harness and match the wire functions. • Connect all the harnesses to the Maestro RR module then test your installation. • Remove the factory radio.
Toyota Venza With JBL and Nav 2013-2014 WIRING DIAGRAM STEP 5 STEP 1 WHITE WHITE/BLACK GRAY GRAY/BLACK GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Venza With JBL and Nav 2013-2014 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+) Yellow/Black Yellow/Black N
Toyota Venza With JBL and Nav 2013-2014 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure 2 pin black connector is plugged into the 2 pin black of the 28 pin connector of the TO2 harness, not the OBD2. Reset the RR. Gauges work but are limited or data features are limited (turn signals, very limited gauge functionality).
INSTALL GUIDE 2015-2016 Toyota Venza Without JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-TO2 Installation Harness E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-DS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Toyota Venza Without JBL 2015-2016 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Toyota Venza Without JBL 2015-2016 INSTALLATION INSTRUCTIONS STEP 6 STEP 1 • Connect all the harnesses to the Maestro RR module then test your installation. • Unbox the aftermarket radio and locate its main harness. • Cut and remove the front speaker RCA connectors. • Connect the wires shown on the next page from aftermarket radio main harness to the TO2 T-harness and match the wire functions. • Remove the factory radio.
Toyota Venza Without JBL 2015-2016 WIRING DIAGRAM STEP 5 STEP 1 PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT. CUT AND REMOVE THE SPEAKER WIRE RCA CONNECTORS WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Venza Without JBL 2015-2016 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+) Yellow/Black Yellow/Black N⁄A N
Toyota Venza Without JBL 2015-2016 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure 2 pin black connector is plugged into the 2 pin black of the 28 pin connector of the TO2 harness, not the OBD2. Reset the RR. Gauges work but are limited or data features are limited (turn signals, very limited gauge functionality).
SELECT VEHICLE PRINT PAGES NEEDED HOW TO USE THIS INSTALL GUIDE 1 Open the Bookmarks menu and find your vehicle OR scroll down until you find the install guide for your vehicle. 2 Print only the pages for your vehicle using the advanced options in the Print menu. 3 Install your Maestro RR according to the guide for your vehicle. WARNING Pressing the printer icon or “quick printing” this document will print all of the guides in this compilation. NOTICE: Automotive Data Solutions Inc.
INSTALL GUIDE 2014-2019 Toyota 4 Runner With JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-TO2 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-AS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician.
Toyota 4 Runner With JBL 2014-2019 WELCOME Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. TABLE OF CONTENTS Installation Instructions 3 Wiring Diagram 4 Troubleshooting Table 5 Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware for your vehicle and that you carefully review the install guide.
Toyota 4 Runner With JBL 2014-2019 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on the next page from aftermarket radio main harness to the TO2 T-harness and match the wire functions. • Remove the factory radio. STEP 2 • If the vehicle is equipped with an OEM backup camera, connect the TO2 T-harness to the backup camera harness. STEP 3 • Connect the factory harness to the TO2 T-harness.
Toyota 4 Runner With JBL 2014-2019 WIRING DIAGRAM with an Amplifier STEP 5 STEP 1 WHITE WHITE/BLACK GRAY GRAY/BLACK GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota 4 Runner With JBL 2014-2019 TROUBLESHOOTING TABLE PROBLEM SOLUTION When a button on the steering wheel is pressed, the light on the Maestro module blinks but the radio does not respond. Ensure the blue 4-pin steering wheel control cable is connected between the maestro and the radio (the radio will use either the 3.5mm jack or the Blue/ Yellow wire, not both). Refer to radio’s owners manual to verifie if the radio has this function: Steering Wheel Control (ON/OFF) : choose ON.
INSTALL GUIDE 2014-2019 Toyota 4 Runner Without JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-TO2 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-AS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician.
Toyota 4 Runner Without JBL 2014-2019 WELCOME Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. TABLE OF CONTENTS Installation Instructions 3 Wiring Diagram 4 Troubleshooting Table 5 Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware for your vehicle and that you carefully review the install guide.
Toyota 4 Runner Without JBL 2014-2019 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Cut and remove the front speaker wire junction connectors. • Connect the wires shown on the next page from aftermarket radio main harness to the TO2 T-harness and match the wire functions. • Remove the factory radio. STEP 2 • If the vehicle is equipped with an OEM backup camera, connect the TO2 T-harness to the backup camera harness.
Toyota 4 Runner Without JBL 2014-2019 WIRING DIAGRAM without an Amplifier STEP 5 STEP 1 CUT AND REMOVE THE SPEAKER WIRE JUNCTION CONNECTORS WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota 4 Runner Without JBL 2014-2019 TROUBLESHOOTING TABLE PROBLEM SOLUTION When a button on the steering wheel is pressed, the light on the Maestro module blinks but the radio does not respond. Ensure the blue 4-pin steering wheel control cable is connected between the maestro and the radio (the radio will use either the 3.5mm jack or the Blue/ Yellow wire, not both). Refer to radio’s owners manual to verifie if the radio has this function: Steering Wheel Control (ON/OFF) : choose ON.
INSTALL GUIDE 2015-2019 Toyota Avalon With JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-TO2 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-AS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician.
Toyota Avalon With JBL 2015-2019 WELCOME Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. TABLE OF CONTENTS Installation Instructions 3 Wiring Diagram 4 Troubleshooting Table 5 Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware for your vehicle and that you carefully review the install guide.
Toyota Avalon With JBL 2015-2019 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on the next page from aftermarket radio main harness to the TO2 T-harness and match the wire functions. • Remove the factory radio. STEP 2 • If the vehicle is equipped with an OEM backup camera, connect the TO2 T-harness to the backup camera harness. STEP 3 • Connect the factory harness to the TO2 T-harness.
Toyota Avalon With JBL 2015-2019 WIRING DIAGRAM with an Amplifier STEP 5 STEP 1 WHITE WHITE/BLACK GRAY GRAY/BLACK GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Avalon With JBL 2015-2019 TROUBLESHOOTING TABLE PROBLEM SOLUTION When a button on the steering wheel is pressed, the light on the Maestro module blinks but the radio does not respond. Ensure the blue 4-pin steering wheel control cable is connected between the maestro and the radio (the radio will use either the 3.5mm jack or the Blue/ Yellow wire, not both). Refer to radio’s owners manual to verifie if the radio has this function: Steering Wheel Control (ON/OFF) : choose ON.
INSTALL GUIDE 2013-2014 Toyota Avalon With NAV With JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-TO2 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-AS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician.
Toyota Avalon With NAV With JBL 2013-2014 WELCOME Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Toyota Avalon With NAV With JBL 2013-2014 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on the next page from aftermarket radio main harness to the TO2 T-harness and match the wire functions. • Remove the factory radio.
Toyota Avalon With NAV With JBL 2013-2014 WIRING DIAGRAM with an Amplifier STEP 5 STEP 1 WHITE WHITE/BLACK GRAY GRAY/BLACK GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Avalon With NAV With JBL 2013-2014 TROUBLESHOOTING TABLE PROBLEM SOLUTION When a button on the steering wheel is pressed, the light on the Maestro module blinks but the radio does not respond. Ensure the blue 4-pin steering wheel control cable is connected between the maestro and the radio (the radio will use either the 3.5mm jack or the Blue/ Yellow wire, not both). Refer to radio’s owners manual to verifie if the radio has this function: Steering Wheel Control (ON/OFF) : choose ON.
INSTALL GUIDE 2013-2014 Toyota Avalon With NAV Without JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-TO2 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-AS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician.
Toyota Avalon With NAV Without JBL 2013-2014 WELCOME Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Toyota Avalon With NAV Without JBL 2013-2014 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Cut and remove the front speaker wire junction connectors. • Connect the wires shown on the next page from aftermarket radio main harness to the TO2 T-harness and match the wire functions. • Remove the factory radio.
Toyota Avalon With NAV Without JBL 2013-2014 WIRING DIAGRAM without an Amplifier STEP 5 STEP 1 CUT AND REMOVE THE SPEAKER WIRE JUNCTION CONNECTORS WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Avalon With NAV Without JBL 2013-2014 TROUBLESHOOTING TABLE PROBLEM SOLUTION When a button on the steering wheel is pressed, the light on the Maestro module blinks but the radio does not respond. Ensure the blue 4-pin steering wheel control cable is connected between the maestro and the radio (the radio will use either the 3.5mm jack or the Blue/ Yellow wire, not both). Refer to radio’s owners manual to verifie if the radio has this function: Steering Wheel Control (ON/OFF) : choose ON.
INSTALL GUIDE 2015-2019 Toyota Avalon Without JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-TO2 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-AS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician.
Toyota Avalon Without JBL 2015-2019 WELCOME Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. TABLE OF CONTENTS Installation Instructions 3 Wiring Diagram 4 Troubleshooting Table 5 Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware for your vehicle and that you carefully review the install guide.
Toyota Avalon Without JBL 2015-2019 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Cut and remove the front speaker wire junction connectors. • Connect the wires shown on the next page from aftermarket radio main harness to the TO2 T-harness and match the wire functions. • Remove the factory radio. STEP 2 • If the vehicle is equipped with an OEM backup camera, connect the TO2 T-harness to the backup camera harness.
Toyota Avalon Without JBL 2015-2019 WIRING DIAGRAM without an Amplifier STEP 5 STEP 1 CUT AND REMOVE THE SPEAKER WIRE JUNCTION CONNECTORS WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Avalon Without JBL 2015-2019 TROUBLESHOOTING TABLE PROBLEM SOLUTION When a button on the steering wheel is pressed, the light on the Maestro module blinks but the radio does not respond. Ensure the blue 4-pin steering wheel control cable is connected between the maestro and the radio (the radio will use either the 3.5mm jack or the Blue/ Yellow wire, not both). Refer to radio’s owners manual to verifie if the radio has this function: Steering Wheel Control (ON/OFF) : choose ON.
INSTALL GUIDE 2018 Toyota C-HR Without Apple Carplay or Android Auto RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-TO2 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-AS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician.
Toyota C-HR Without Apple Carplay or Android Auto 2018 WELCOME Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Toyota C-HR Without Apple Carplay or Android Auto 2018 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Cut and remove the front speaker wire junction connectors. • Connect the wires shown on the next page from aftermarket radio main harness to the TO2 T-harness and match the wire functions. • Remove the factory radio. STEP 2 • Connect the factory harness to the TO2 T-harness.
Toyota C-HR Without Apple Carplay or Android Auto 2018 WIRING DIAGRAM without an Amplifier STEP 4 STEP 1 CUT AND REMOVE THE SPEAKER WIRE JUNCTION CONNECTORS WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota C-HR Without Apple Carplay or Android Auto 2018 TROUBLESHOOTING TABLE PROBLEM SOLUTION When a button on the steering wheel is pressed, the light on the Maestro module blinks but the radio does not respond. Ensure the blue 4-pin steering wheel control cable is connected between the maestro and the radio (the radio will use either the 3.5mm jack or the Blue/ Yellow wire, not both). Refer to radio’s owners manual to verifie if the radio has this function: Steering Wheel Control (ON/OFF) : choose ON.
INSTALL GUIDE 2012-2014 Toyota Camry With Factory 6.1" Screen RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-TO2 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-AS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician.
Toyota Camry With Factory 6.1" Screen 2012-2014 WELCOME Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Toyota Camry With Factory 6.1" Screen 2012-2014 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Cut and remove the front speaker wire junction connectors. • Connect the wires shown on the next page from aftermarket radio main harness to the TO2 T-harness and match the wire functions. • Remove the factory radio.
Toyota Camry With Factory 6.1" Screen 2012-2014 WIRING DIAGRAM without an Amplifier STEP 5 STEP 1 CUT AND REMOVE THE SPEAKER WIRE JUNCTION CONNECTORS WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Camry With Factory 6.1" Screen 2012-2014 TROUBLESHOOTING TABLE PROBLEM SOLUTION When a button on the steering wheel is pressed, the light on the Maestro module blinks but the radio does not respond. Ensure the blue 4-pin steering wheel control cable is connected between the maestro and the radio (the radio will use either the 3.5mm jack or the Blue/ Yellow wire, not both). Refer to radio’s owners manual to verifie if the radio has this function: Steering Wheel Control (ON/OFF) : choose ON.
INSTALL GUIDE 2012-2014 Toyota Camry With Factory 6.1" Screen and JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-TO2 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-AS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician.
Toyota Camry With Factory 6.1" Screen and JBL 2012-2014 WELCOME Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Toyota Camry With Factory 6.1" Screen and JBL 2012-2014 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on the next page from aftermarket radio main harness to the TO2 T-harness and match the wire functions. • Remove the factory radio.
Toyota Camry With Factory 6.1" Screen and JBL 2012-2014 WIRING DIAGRAM with an Amplifier STEP 5 STEP 1 WHITE WHITE/BLACK GRAY GRAY/BLACK GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Camry With Factory 6.1" Screen and JBL 2012-2014 TROUBLESHOOTING TABLE PROBLEM SOLUTION When a button on the steering wheel is pressed, the light on the Maestro module blinks but the radio does not respond. Ensure the blue 4-pin steering wheel control cable is connected between the maestro and the radio (the radio will use either the 3.5mm jack or the Blue/ Yellow wire, not both). Refer to radio’s owners manual to verifie if the radio has this function: Steering Wheel Control (ON/OFF) : choose ON.
INSTALL GUIDE 2012-2014 Toyota Camry With Factory Screen and HDD and JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-TO2 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-AS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician.
Toyota Camry With Factory Screen and HDD and JBL 2012-2014 WELCOME Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Toyota Camry With Factory Screen and HDD and JBL 2012-2014 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on the next page from aftermarket radio main harness to the TO2 T-harness and match the wire functions. • Remove the factory radio.
Toyota Camry With Factory Screen and HDD and JBL 2012-2014 WIRING DIAGRAM with an Amplifier STEP 5 STEP 1 WHITE WHITE/BLACK GRAY GRAY/BLACK GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Camry With Factory Screen and HDD and JBL 2012-2014 TROUBLESHOOTING TABLE PROBLEM SOLUTION When a button on the steering wheel is pressed, the light on the Maestro module blinks but the radio does not respond. Ensure the blue 4-pin steering wheel control cable is connected between the maestro and the radio (the radio will use either the 3.5mm jack or the Blue/ Yellow wire, not both).
INSTALL GUIDE 2015-2017 Toyota Camry With JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-TO2 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-AS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician.
Toyota Camry With JBL 2015-2017 WELCOME Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. TABLE OF CONTENTS Installation Instructions 3 Wiring Diagram 4 Troubleshooting Table 5 Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware for your vehicle and that you carefully review the install guide.
Toyota Camry With JBL 2015-2017 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on the next page from aftermarket radio main harness to the TO2 T-harness and match the wire functions. • Remove the factory radio. STEP 2 • If the vehicle is equipped with an OEM backup camera, connect the TO2 T-harness to the backup camera harness. STEP 3 • Connect the factory harness to the TO2 T-harness.
Toyota Camry With JBL 2015-2017 WIRING DIAGRAM with an Amplifier STEP 5 STEP 1 WHITE WHITE/BLACK GRAY GRAY/BLACK GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Camry With JBL 2015-2017 TROUBLESHOOTING TABLE PROBLEM SOLUTION When a button on the steering wheel is pressed, the light on the Maestro module blinks but the radio does not respond. Ensure the blue 4-pin steering wheel control cable is connected between the maestro and the radio (the radio will use either the 3.5mm jack or the Blue/ Yellow wire, not both). Refer to radio’s owners manual to verifie if the radio has this function: Steering Wheel Control (ON/OFF) : choose ON.
INSTALL GUIDE 2015-2017 Toyota Camry Without JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-TO2 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-AS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician.
Toyota Camry Without JBL 2015-2017 WELCOME Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. TABLE OF CONTENTS Installation Instructions 3 Wiring Diagram 4 Troubleshooting Table 5 Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware for your vehicle and that you carefully review the install guide.
Toyota Camry Without JBL 2015-2017 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Cut and remove the front speaker wire junction connectors. • Connect the wires shown on the next page from aftermarket radio main harness to the TO2 T-harness and match the wire functions. • Remove the factory radio. STEP 2 • If the vehicle is equipped with an OEM backup camera, connect the TO2 T-harness to the backup camera harness.
Toyota Camry Without JBL 2015-2017 WIRING DIAGRAM without an Amplifier STEP 5 STEP 1 CUT AND REMOVE THE SPEAKER WIRE JUNCTION CONNECTORS WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Camry Without JBL 2015-2017 TROUBLESHOOTING TABLE PROBLEM SOLUTION When a button on the steering wheel is pressed, the light on the Maestro module blinks but the radio does not respond. Ensure the blue 4-pin steering wheel control cable is connected between the maestro and the radio (the radio will use either the 3.5mm jack or the Blue/ Yellow wire, not both). Refer to radio’s owners manual to verifie if the radio has this function: Steering Wheel Control (ON/OFF) : choose ON.
INSTALL GUIDE 2014-2019 Toyota Corolla With Factory 6.1" Screen RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-TO2 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-AS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician.
Toyota Corolla With Factory 6.1" Screen 2014-2019 WELCOME Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Toyota Corolla With Factory 6.1" Screen 2014-2019 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Cut and remove the front speaker wire junction connectors. • Connect the wires shown on the next page from aftermarket radio main harness to the TO2 T-harness and match the wire functions. • Remove the factory radio. STEP 2 • If the vehicle is equipped with an OEM backup camera, connect the TO2 T-harness to the backup camera harness.
Toyota Corolla With Factory 6.1" Screen 2014-2019 WIRING DIAGRAM without an Amplifier STEP 5 STEP 1 CUT AND REMOVE THE SPEAKER WIRE JUNCTION CONNECTORS WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Corolla With Factory 6.1" Screen 2014-2019 TROUBLESHOOTING TABLE PROBLEM SOLUTION When a button on the steering wheel is pressed, the light on the Maestro module blinks but the radio does not respond. Ensure the blue 4-pin steering wheel control cable is connected between the maestro and the radio (the radio will use either the 3.5mm jack or the Blue/ Yellow wire, not both). Refer to radio’s owners manual to verifie if the radio has this function: Steering Wheel Control (ON/OFF) : choose ON.
INSTALL GUIDE 2014-2019 Toyota Highlander With JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-TO2 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-AS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician.
Toyota Highlander With JBL 2014-2019 WELCOME Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. TABLE OF CONTENTS Installation Instructions 3 Wiring Diagram 4 Troubleshooting Table 5 Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware for your vehicle and that you carefully review the install guide.
Toyota Highlander With JBL 2014-2019 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on the next page from aftermarket radio main harness to the TO2 T-harness and match the wire functions. • Remove the factory radio. STEP 2 • If the vehicle is equipped with an OEM backup camera, connect the TO2 T-harness to the backup camera harness. STEP 3 • Connect the factory harness to the TO2 T-harness.
Toyota Highlander With JBL 2014-2019 WIRING DIAGRAM with an Amplifier STEP 5 STEP 1 WHITE WHITE/BLACK GRAY GRAY/BLACK GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Highlander With JBL 2014-2019 TROUBLESHOOTING TABLE PROBLEM SOLUTION When a button on the steering wheel is pressed, the light on the Maestro module blinks but the radio does not respond. Ensure the blue 4-pin steering wheel control cable is connected between the maestro and the radio (the radio will use either the 3.5mm jack or the Blue/ Yellow wire, not both). Refer to radio’s owners manual to verifie if the radio has this function: Steering Wheel Control (ON/OFF) : choose ON.
INSTALL GUIDE 2014-2019 Toyota Highlander Without JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-TO2 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-AS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician.
Toyota Highlander Without JBL 2014-2019 WELCOME Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Toyota Highlander Without JBL 2014-2019 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Cut and remove the front speaker wire junction connectors. • Connect the wires shown on the next page from aftermarket radio main harness to the TO2 T-harness and match the wire functions. • Remove the factory radio. STEP 2 • If the vehicle is equipped with an OEM backup camera, connect the TO2 T-harness to the backup camera harness.
Toyota Highlander Without JBL 2014-2019 WIRING DIAGRAM without an Amplifier STEP 5 STEP 1 CUT AND REMOVE THE SPEAKER WIRE JUNCTION CONNECTORS WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Highlander Without JBL 2014-2019 TROUBLESHOOTING TABLE PROBLEM SOLUTION When a button on the steering wheel is pressed, the light on the Maestro module blinks but the radio does not respond. Ensure the blue 4-pin steering wheel control cable is connected between the maestro and the radio (the radio will use either the 3.5mm jack or the Blue/ Yellow wire, not both). Refer to radio’s owners manual to verifie if the radio has this function: Steering Wheel Control (ON/OFF) : choose ON.
INSTALL GUIDE 2016-2019 Toyota Prius Base RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-TO2 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-AS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician.
Toyota Prius Base 2016-2019 WELCOME Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. TABLE OF CONTENTS Installation Instructions 3 Wiring Diagram 4 Troubleshooting Table 5 Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware for your vehicle and that you carefully review the install guide.
Toyota Prius Base 2016-2019 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Cut and remove the front speaker wire junction connectors. • Connect the wires shown on the next page from aftermarket radio main harness to the TO2 T-harness and match the wire functions. • Remove the factory radio. STEP 2 • If the vehicle is equipped with an OEM backup camera, connect the TO2 T-harness to the backup camera harness.
Toyota Prius Base 2016-2019 WIRING DIAGRAM without an Amplifier STEP 5 STEP 1 CUT AND REMOVE THE SPEAKER WIRE JUNCTION CONNECTORS WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Prius Base 2016-2019 TROUBLESHOOTING TABLE PROBLEM SOLUTION When a button on the steering wheel is pressed, the light on the Maestro module blinks but the radio does not respond. Ensure the blue 4-pin steering wheel control cable is connected between the maestro and the radio (the radio will use either the 3.5mm jack or the Blue/ Yellow wire, not both). Refer to radio’s owners manual to verifie if the radio has this function: Steering Wheel Control (ON/OFF) : choose ON.
INSTALL GUIDE 2015-2019 Toyota Prius C With JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-TO2 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-AS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician.
Toyota Prius C With JBL 2015-2019 WELCOME Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. TABLE OF CONTENTS Installation Instructions 3 Wiring Diagram 4 Troubleshooting Table 5 Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware for your vehicle and that you carefully review the install guide.
Toyota Prius C With JBL 2015-2019 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on the next page from aftermarket radio main harness to the TO2 T-harness and match the wire functions. • Remove the factory radio. STEP 2 • If the vehicle is equipped with an OEM backup camera, connect the TO2 T-harness to the backup camera harness. STEP 3 • Connect the factory harness to the TO2 T-harness.
Toyota Prius C With JBL 2015-2019 WIRING DIAGRAM with an Amplifier STEP 5 STEP 1 WHITE WHITE/BLACK GRAY GRAY/BLACK GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Prius C With JBL 2015-2019 TROUBLESHOOTING TABLE PROBLEM SOLUTION When a button on the steering wheel is pressed, the light on the Maestro module blinks but the radio does not respond. Ensure the blue 4-pin steering wheel control cable is connected between the maestro and the radio (the radio will use either the 3.5mm jack or the Blue/ Yellow wire, not both). Refer to radio’s owners manual to verifie if the radio has this function: Steering Wheel Control (ON/OFF) : choose ON.
INSTALL GUIDE 2012-2014 Toyota Prius C Without JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-TO2 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-AS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician.
Toyota Prius C Without JBL 2012-2014 WELCOME Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. TABLE OF CONTENTS Installation Instructions 3 Wiring Diagram 4 Troubleshooting Table 5 Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware for your vehicle and that you carefully review the install guide.
Toyota Prius C Without JBL 2012-2014 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Cut and remove the front speaker wire junction connectors. • Connect the wires shown on the next page from aftermarket radio main harness to the TO2 T-harness and match the wire functions. • Remove the factory radio. STEP 2 • If the vehicle is equipped with an OEM backup camera, connect the TO2 T-harness to the backup camera harness.
Toyota Prius C Without JBL 2012-2014 WIRING DIAGRAM without an Amplifier STEP 5 STEP 1 CUT AND REMOVE THE SPEAKER WIRE JUNCTION CONNECTORS WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Prius C Without JBL 2012-2014 TROUBLESHOOTING TABLE PROBLEM SOLUTION When a button on the steering wheel is pressed, the light on the Maestro module blinks but the radio does not respond. Ensure the blue 4-pin steering wheel control cable is connected between the maestro and the radio (the radio will use either the 3.5mm jack or the Blue/ Yellow wire, not both). Refer to radio’s owners manual to verifie if the radio has this function: Steering Wheel Control (ON/OFF) : choose ON.
INSTALL GUIDE 2015-2019 Toyota Prius C Without JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-TO2 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-AS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician.
Toyota Prius C Without JBL 2015-2019 WELCOME Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. TABLE OF CONTENTS Installation Instructions 3 Wiring Diagram 4 Troubleshooting Table 5 Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware for your vehicle and that you carefully review the install guide.
Toyota Prius C Without JBL 2015-2019 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Cut and remove the front speaker wire junction connectors. • Connect the wires shown on the next page from aftermarket radio main harness to the TO2 T-harness and match the wire functions. • Remove the factory radio. STEP 2 • If the vehicle is equipped with an OEM backup camera, connect the TO2 T-harness to the backup camera harness.
Toyota Prius C Without JBL 2015-2019 WIRING DIAGRAM without an Amplifier STEP 5 STEP 1 CUT AND REMOVE THE SPEAKER WIRE JUNCTION CONNECTORS WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Prius C Without JBL 2015-2019 TROUBLESHOOTING TABLE PROBLEM SOLUTION When a button on the steering wheel is pressed, the light on the Maestro module blinks but the radio does not respond. Ensure the blue 4-pin steering wheel control cable is connected between the maestro and the radio (the radio will use either the 3.5mm jack or the Blue/ Yellow wire, not both). Refer to radio’s owners manual to verifie if the radio has this function: Steering Wheel Control (ON/OFF) : choose ON.
INSTALL GUIDE 2012-2014 Toyota Prius V With JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-TO2 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-AS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician.
Toyota Prius V With JBL 2012-2014 WELCOME Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. TABLE OF CONTENTS Installation Instructions 3 Wiring Diagram 4 Troubleshooting Table 5 Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware for your vehicle and that you carefully review the install guide.
Toyota Prius V With JBL 2012-2014 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on the next page from aftermarket radio main harness to the TO2 T-harness and match the wire functions. • Remove the factory radio.
Toyota Prius V With JBL 2012-2014 WIRING DIAGRAM with an Amplifier STEP 5 STEP 1 WHITE WHITE/BLACK GRAY GRAY/BLACK GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Prius V With JBL 2012-2014 TROUBLESHOOTING TABLE PROBLEM SOLUTION When a button on the steering wheel is pressed, the light on the Maestro module blinks but the radio does not respond. Ensure the blue 4-pin steering wheel control cable is connected between the maestro and the radio (the radio will use either the 3.5mm jack or the Blue/ Yellow wire, not both). Refer to radio’s owners manual to verifie if the radio has this function: Steering Wheel Control (ON/OFF) : choose ON.
INSTALL GUIDE 2015-2017 Toyota Prius V With JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-TO2 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-AS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician.
Toyota Prius V With JBL 2015-2017 WELCOME Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. TABLE OF CONTENTS Installation Instructions 3 Wiring Diagram 4 Troubleshooting Table 5 Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware for your vehicle and that you carefully review the install guide.
Toyota Prius V With JBL 2015-2017 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on the next page from aftermarket radio main harness to the TO2 T-harness and match the wire functions. • Remove the factory radio. STEP 2 • If the vehicle is equipped with an OEM backup camera, connect the TO2 T-harness to the backup camera harness. STEP 3 • Connect the factory harness to the TO2 T-harness.
Toyota Prius V With JBL 2015-2017 WIRING DIAGRAM with an Amplifier STEP 5 STEP 1 WHITE WHITE/BLACK GRAY GRAY/BLACK GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Prius V With JBL 2015-2017 TROUBLESHOOTING TABLE PROBLEM SOLUTION When a button on the steering wheel is pressed, the light on the Maestro module blinks but the radio does not respond. Ensure the blue 4-pin steering wheel control cable is connected between the maestro and the radio (the radio will use either the 3.5mm jack or the Blue/ Yellow wire, not both). Refer to radio’s owners manual to verifie if the radio has this function: Steering Wheel Control (ON/OFF) : choose ON.
INSTALL GUIDE 2012-2014 Toyota Prius V Without JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-TO2 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-AS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician.
Toyota Prius V Without JBL 2012-2014 WELCOME Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. TABLE OF CONTENTS Installation Instructions 3 Wiring Diagram 4 Troubleshooting Table 5 Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware for your vehicle and that you carefully review the install guide.
Toyota Prius V Without JBL 2012-2014 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Cut and remove the front speaker wire junction connectors. • Connect the wires shown on the next page from aftermarket radio main harness to the TO2 T-harness and match the wire functions. • Remove the factory radio.
Toyota Prius V Without JBL 2012-2014 WIRING DIAGRAM without an Amplifier STEP 5 STEP 1 CUT AND REMOVE THE SPEAKER WIRE JUNCTION CONNECTORS WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Prius V Without JBL 2012-2014 TROUBLESHOOTING TABLE PROBLEM SOLUTION When a button on the steering wheel is pressed, the light on the Maestro module blinks but the radio does not respond. Ensure the blue 4-pin steering wheel control cable is connected between the maestro and the radio (the radio will use either the 3.5mm jack or the Blue/ Yellow wire, not both). Refer to radio’s owners manual to verifie if the radio has this function: Steering Wheel Control (ON/OFF) : choose ON.
INSTALL GUIDE 2015-2017 Toyota Prius V Without JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-TO2 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-AS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician.
Toyota Prius V Without JBL 2015-2017 WELCOME Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. TABLE OF CONTENTS Installation Instructions 3 Wiring Diagram 4 Troubleshooting Table 5 Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware for your vehicle and that you carefully review the install guide.
Toyota Prius V Without JBL 2015-2017 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Cut and remove the front speaker wire junction connectors. • Connect the wires shown on the next page from aftermarket radio main harness to the TO2 T-harness and match the wire functions. • Remove the factory radio. STEP 2 • If the vehicle is equipped with an OEM backup camera, connect the TO2 T-harness to the backup camera harness.
Toyota Prius V Without JBL 2015-2017 WIRING DIAGRAM without an Amplifier STEP 5 STEP 1 CUT AND REMOVE THE SPEAKER WIRE JUNCTION CONNECTORS WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Prius V Without JBL 2015-2017 TROUBLESHOOTING TABLE PROBLEM SOLUTION When a button on the steering wheel is pressed, the light on the Maestro module blinks but the radio does not respond. Ensure the blue 4-pin steering wheel control cable is connected between the maestro and the radio (the radio will use either the 3.5mm jack or the Blue/ Yellow wire, not both). Refer to radio’s owners manual to verifie if the radio has this function: Steering Wheel Control (ON/OFF) : choose ON.
INSTALL GUIDE 2012-2014 Toyota Prius With JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-TO2 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-AS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician.
Toyota Prius With JBL 2012-2014 WELCOME Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. TABLE OF CONTENTS Installation Instructions 3 Wiring Diagram 4 Troubleshooting Table 5 Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware for your vehicle and that you carefully review the install guide.
Toyota Prius With JBL 2012-2014 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on the next page from aftermarket radio main harness to the TO2 T-harness and match the wire functions. • Remove the factory radio. STEP 2 • If the vehicle is equipped with an OEM backup camera: Cut the reverse camera plug of the TO2 T-harness and connect the wires as indicated in the wiring diagram next page (BROWN/RED and BROWN/YELLOW wires are not used).
Toyota Prius With JBL 2012-2014 WIRING DIAGRAM with an Amplifier STEP 5 STEP 1 WHITE WHITE/BLACK GRAY GRAY/BLACK GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Prius With JBL 2012-2014 TROUBLESHOOTING TABLE PROBLEM SOLUTION When a button on the steering wheel is pressed, the light on the Maestro module blinks but the radio does not respond. Ensure the blue 4-pin steering wheel control cable is connected between the maestro and the radio (the radio will use either the 3.5mm jack or the Blue/ Yellow wire, not both). Refer to radio’s owners manual to verifie if the radio has this function: Steering Wheel Control (ON/OFF) : choose ON.
INSTALL GUIDE 2015-2019 Toyota Prius With JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-TO2 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-AS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician.
Toyota Prius With JBL 2015-2019 WELCOME Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. TABLE OF CONTENTS Installation Instructions 3 Wiring Diagram 4 Troubleshooting Table 5 Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware for your vehicle and that you carefully review the install guide.
Toyota Prius With JBL 2015-2019 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on the next page from aftermarket radio main harness to the TO2 T-harness and match the wire functions. • Remove the factory radio. STEP 2 • If the vehicle is equipped with an OEM backup camera, connect the TO2 T-harness to the backup camera harness. STEP 3 • Connect the factory harness to the TO2 T-harness.
Toyota Prius With JBL 2015-2019 WIRING DIAGRAM with an Amplifier STEP 5 STEP 1 WHITE WHITE/BLACK GRAY GRAY/BLACK GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Prius With JBL 2015-2019 TROUBLESHOOTING TABLE PROBLEM SOLUTION When a button on the steering wheel is pressed, the light on the Maestro module blinks but the radio does not respond. Ensure the blue 4-pin steering wheel control cable is connected between the maestro and the radio (the radio will use either the 3.5mm jack or the Blue/ Yellow wire, not both). Refer to radio’s owners manual to verifie if the radio has this function: Steering Wheel Control (ON/OFF) : choose ON.
INSTALL GUIDE 2012-2014 Toyota Prius With Nav Without JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-TO2 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-AS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician.
Toyota Prius With Nav Without JBL 2012-2014 WELCOME Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Toyota Prius With Nav Without JBL 2012-2014 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Cut and remove the front speaker wire junction connectors. • Connect the wires shown on the next page from aftermarket radio main harness to the TO2 T-harness and match the wire functions. • Remove the factory radio.
Toyota Prius With Nav Without JBL 2012-2014 WIRING DIAGRAM without an Amplifier STEP 5 STEP 1 CUT AND REMOVE THE SPEAKER WIRE JUNCTION CONNECTORS WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Prius With Nav Without JBL 2012-2014 TROUBLESHOOTING TABLE PROBLEM SOLUTION When a button on the steering wheel is pressed, the light on the Maestro module blinks but the radio does not respond. Ensure the blue 4-pin steering wheel control cable is connected between the maestro and the radio (the radio will use either the 3.5mm jack or the Blue/ Yellow wire, not both). Refer to radio’s owners manual to verifie if the radio has this function: Steering Wheel Control (ON/OFF) : choose ON.
INSTALL GUIDE 2015-2019 Toyota Prius With Nav Without JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-TO2 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-AS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician.
Toyota Prius With Nav Without JBL 2015-2019 WELCOME Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Toyota Prius With Nav Without JBL 2015-2019 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Cut and remove the front speaker wire junction connectors. • Connect the wires shown on the next page from aftermarket radio main harness to the TO2 T-harness and match the wire functions. • Remove the factory radio. STEP 2 • If the vehicle is equipped with an OEM backup camera, connect the TO2 T-harness to the backup camera harness.
Toyota Prius With Nav Without JBL 2015-2019 WIRING DIAGRAM without an Amplifier STEP 5 STEP 1 CUT AND REMOVE THE SPEAKER WIRE JUNCTION CONNECTORS WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Prius With Nav Without JBL 2015-2019 TROUBLESHOOTING TABLE PROBLEM SOLUTION When a button on the steering wheel is pressed, the light on the Maestro module blinks but the radio does not respond. Ensure the blue 4-pin steering wheel control cable is connected between the maestro and the radio (the radio will use either the 3.5mm jack or the Blue/ Yellow wire, not both). Refer to radio’s owners manual to verifie if the radio has this function: Steering Wheel Control (ON/OFF) : choose ON.
INSTALL GUIDE 2013-2018 Toyota Rav 4 With Factory 6.1" Screen RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-TO2 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-AS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician.
Toyota Rav 4 With Factory 6.1" Screen 2013-2018 WELCOME Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Toyota Rav 4 With Factory 6.1" Screen 2013-2018 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Cut and remove the front speaker wire junction connectors. • Connect the wires shown on the next page from aftermarket radio main harness to the TO2 T-harness and match the wire functions. • Remove the factory radio. STEP 2 • If the vehicle is equipped with an OEM backup camera, connect the TO2 T-harness to the backup camera harness.
Toyota Rav 4 With Factory 6.1" Screen 2013-2018 WIRING DIAGRAM without an Amplifier STEP 5 STEP 1 CUT AND REMOVE THE SPEAKER WIRE JUNCTION CONNECTORS WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Rav 4 With Factory 6.1" Screen 2013-2018 TROUBLESHOOTING TABLE PROBLEM SOLUTION When a button on the steering wheel is pressed, the light on the Maestro module blinks but the radio does not respond. Ensure the blue 4-pin steering wheel control cable is connected between the maestro and the radio (the radio will use either the 3.5mm jack or the Blue/ Yellow wire, not both). Refer to radio’s owners manual to verifie if the radio has this function: Steering Wheel Control (ON/OFF) : choose ON.
INSTALL GUIDE 2013-2018 Toyota Rav 4 With Factory 6.1" Screen and JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-TO2 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-AS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician.
Toyota Rav 4 With Factory 6.1" Screen and JBL 2013-2018 WELCOME Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Toyota Rav 4 With Factory 6.1" Screen and JBL 2013-2018 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on the next page from aftermarket radio main harness to the TO2 T-harness and match the wire functions. • Remove the factory radio. STEP 2 • If the vehicle is equipped with an OEM backup camera, connect the TO2 T-harness to the backup camera harness. STEP 3 • Connect the factory harness to the TO2 T-harness.
Toyota Rav 4 With Factory 6.1" Screen and JBL 2013-2018 WIRING DIAGRAM with an Amplifier STEP 5 STEP 1 WHITE WHITE/BLACK GRAY GRAY/BLACK GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Rav 4 With Factory 6.1" Screen and JBL 2013-2018 TROUBLESHOOTING TABLE PROBLEM SOLUTION When a button on the steering wheel is pressed, the light on the Maestro module blinks but the radio does not respond. Ensure the blue 4-pin steering wheel control cable is connected between the maestro and the radio (the radio will use either the 3.5mm jack or the Blue/ Yellow wire, not both). Refer to radio’s owners manual to verifie if the radio has this function: Steering Wheel Control (ON/OFF) : choose ON.
INSTALL GUIDE 2014-2019 Toyota Sequoia With JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-TO2 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-AS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician.
Toyota Sequoia With JBL 2014-2019 WELCOME Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. TABLE OF CONTENTS Installation Instructions 3 Wiring Diagram 4 Troubleshooting Table 5 Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware for your vehicle and that you carefully review the install guide.
Toyota Sequoia With JBL 2014-2019 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on the next page from aftermarket radio main harness to the TO2 T-harness and match the wire functions. • Remove the factory radio. STEP 2 • If the vehicle is equipped with an OEM backup camera, connect the TO2 T-harness to the backup camera harness. STEP 3 • Connect the factory harness to the TO2 T-harness.
Toyota Sequoia With JBL 2014-2019 WIRING DIAGRAM with an Amplifier STEP 5 STEP 1 WHITE WHITE/BLACK GRAY GRAY/BLACK GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Sequoia With JBL 2014-2019 TROUBLESHOOTING TABLE PROBLEM SOLUTION When a button on the steering wheel is pressed, the light on the Maestro module blinks but the radio does not respond. Ensure the blue 4-pin steering wheel control cable is connected between the maestro and the radio (the radio will use either the 3.5mm jack or the Blue/ Yellow wire, not both). Refer to radio’s owners manual to verifie if the radio has this function: Steering Wheel Control (ON/OFF) : choose ON.
INSTALL GUIDE 2015-2019 Toyota Sienna With JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-TO2 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-AS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician.
Toyota Sienna With JBL 2015-2019 WELCOME Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. TABLE OF CONTENTS Installation Instructions 3 Wiring Diagram 4 Troubleshooting Table 5 Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware for your vehicle and that you carefully review the install guide.
Toyota Sienna With JBL 2015-2019 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on the next page from aftermarket radio main harness to the TO2 T-harness and match the wire functions. • Remove the factory radio. STEP 2 • If the vehicle is equipped with an OEM backup camera, connect the TO2 T-harness to the backup camera harness. Note: The reverse camera cannot be retained in this vehicle.
Toyota Sienna With JBL 2015-2019 WIRING DIAGRAM with an Amplifier STEP 5 STEP 1 WHITE WHITE/BLACK GRAY GRAY/BLACK GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Sienna With JBL 2015-2019 TROUBLESHOOTING TABLE PROBLEM SOLUTION When a button on the steering wheel is pressed, the light on the Maestro module blinks but the radio does not respond. Ensure the blue 4-pin steering wheel control cable is connected between the maestro and the radio (the radio will use either the 3.5mm jack or the Blue/ Yellow wire, not both). Refer to radio’s owners manual to verifie if the radio has this function: Steering Wheel Control (ON/OFF) : choose ON.
INSTALL GUIDE 2015-2019 Toyota Sienna Without JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-TO2 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-AS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician.
Toyota Sienna Without JBL 2015-2019 WELCOME Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. TABLE OF CONTENTS Installation Instructions 3 Wiring Diagram 4 Troubleshooting Table 5 Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware for your vehicle and that you carefully review the install guide.
Toyota Sienna Without JBL 2015-2019 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Cut and remove the front speaker wire junction connectors. • Connect the wires shown on the next page from aftermarket radio main harness to the TO2 T-harness and match the wire functions. • Remove the factory radio. STEP 2 • If the vehicle is equipped with an OEM backup camera, connect the TO2 T-harness to the backup camera harness.
Toyota Sienna Without JBL 2015-2019 WIRING DIAGRAM without an Amplifier STEP 5 STEP 1 CUT AND REMOVE THE SPEAKER WIRE JUNCTION CONNECTORS WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Sienna Without JBL 2015-2019 TROUBLESHOOTING TABLE PROBLEM SOLUTION When a button on the steering wheel is pressed, the light on the Maestro module blinks but the radio does not respond. Ensure the blue 4-pin steering wheel control cable is connected between the maestro and the radio (the radio will use either the 3.5mm jack or the Blue/ Yellow wire, not both). Refer to radio’s owners manual to verifie if the radio has this function: Steering Wheel Control (ON/OFF) : choose ON.
INSTALL GUIDE 2016-2019 Toyota Tacoma With JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-TO2 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-AS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician.
Toyota Tacoma With JBL 2016-2019 WELCOME Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. TABLE OF CONTENTS Installation Instructions 3 Wiring Diagram 4 Troubleshooting Table 5 Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware for your vehicle and that you carefully review the install guide.
Toyota Tacoma With JBL 2016-2019 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on the next page from aftermarket radio main harness to the TO2 T-harness and match the wire functions. • Remove the factory radio. STEP 2 • If the vehicle is equipped with an OEM backup camera, connect the TO2 T-harness to the backup camera harness. STEP 3 • Connect the factory harness to the TO2 T-harness.
Toyota Tacoma With JBL 2016-2019 WIRING DIAGRAM with an Amplifier STEP 5 STEP 1 WHITE WHITE/BLACK GRAY GRAY/BLACK GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Tacoma With JBL 2016-2019 TROUBLESHOOTING TABLE PROBLEM SOLUTION When a button on the steering wheel is pressed, the light on the Maestro module blinks but the radio does not respond. Ensure the blue 4-pin steering wheel control cable is connected between the maestro and the radio (the radio will use either the 3.5mm jack or the Blue/ Yellow wire, not both). Refer to radio’s owners manual to verifie if the radio has this function: Steering Wheel Control (ON/OFF) : choose ON.
INSTALL GUIDE 2016-2019 Toyota Tacoma Without JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-TO2 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-AS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician.
Toyota Tacoma Without JBL 2016-2019 WELCOME Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. TABLE OF CONTENTS Installation Instructions 3 Wiring Diagram 4 Troubleshooting Table 5 Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware for your vehicle and that you carefully review the install guide.
Toyota Tacoma Without JBL 2016-2019 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Cut and remove the front speaker wire junction connectors. • Connect the wires shown on the next page from aftermarket radio main harness to the TO2 T-harness and match the wire functions. • Remove the factory radio. STEP 2 • If the vehicle is equipped with an OEM backup camera, connect the TO2 T-harness to the backup camera harness.
Toyota Tacoma Without JBL 2016-2019 WIRING DIAGRAM without an Amplifier STEP 5 STEP 1 CUT AND REMOVE THE SPEAKER WIRE JUNCTION CONNECTORS WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Tacoma Without JBL 2016-2019 TROUBLESHOOTING TABLE PROBLEM SOLUTION When a button on the steering wheel is pressed, the light on the Maestro module blinks but the radio does not respond. Ensure the blue 4-pin steering wheel control cable is connected between the maestro and the radio (the radio will use either the 3.5mm jack or the Blue/ Yellow wire, not both). Refer to radio’s owners manual to verifie if the radio has this function: Steering Wheel Control (ON/OFF) : choose ON.
INSTALL GUIDE 2014-2019 Toyota Tundra With JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-TO2 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-AS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician.
Toyota Tundra With JBL 2014-2019 WELCOME Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. TABLE OF CONTENTS Installation Instructions 3 Wiring Diagram 4 Troubleshooting Table 5 Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware for your vehicle and that you carefully review the install guide.
Toyota Tundra With JBL 2014-2019 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on the next page from aftermarket radio main harness to the TO2 T-harness and match the wire functions. • Remove the factory radio. STEP 2 • If the vehicle is equipped with an OEM backup camera, connect the TO2 T-harness to the backup camera harness. STEP 3 • Connect the factory harness to the TO2 T-harness.
Toyota Tundra With JBL 2014-2019 WIRING DIAGRAM with an Amplifier STEP 5 STEP 1 WHITE WHITE/BLACK GRAY GRAY/BLACK GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Tundra With JBL 2014-2019 TROUBLESHOOTING TABLE PROBLEM SOLUTION When a button on the steering wheel is pressed, the light on the Maestro module blinks but the radio does not respond. Ensure the blue 4-pin steering wheel control cable is connected between the maestro and the radio (the radio will use either the 3.5mm jack or the Blue/ Yellow wire, not both). Refer to radio’s owners manual to verifie if the radio has this function: Steering Wheel Control (ON/OFF) : choose ON.
INSTALL GUIDE 2014-2019 Toyota Tundra Without JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-TO2 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-AS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician.
Toyota Tundra Without JBL 2014-2019 WELCOME Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. TABLE OF CONTENTS Installation Instructions 3 Wiring Diagram 4 Troubleshooting Table 5 Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware for your vehicle and that you carefully review the install guide.
Toyota Tundra Without JBL 2014-2019 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Cut and remove the front speaker wire junction connectors. • Connect the wires shown on the next page from aftermarket radio main harness to the TO2 T-harness and match the wire functions. • Remove the factory radio. STEP 2 • If the vehicle is equipped with an OEM backup camera, connect the TO2 T-harness to the backup camera harness.
Toyota Tundra Without JBL 2014-2019 WIRING DIAGRAM without an Amplifier STEP 5 STEP 1 CUT AND REMOVE THE SPEAKER WIRE JUNCTION CONNECTORS WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Tundra Without JBL 2014-2019 TROUBLESHOOTING TABLE PROBLEM SOLUTION When a button on the steering wheel is pressed, the light on the Maestro module blinks but the radio does not respond. Ensure the blue 4-pin steering wheel control cable is connected between the maestro and the radio (the radio will use either the 3.5mm jack or the Blue/ Yellow wire, not both). Refer to radio’s owners manual to verifie if the radio has this function: Steering Wheel Control (ON/OFF) : choose ON.
INSTALL GUIDE 2015-2016 Toyota Venza With JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-TO2 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-AS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician.
Toyota Venza With JBL 2015-2016 WELCOME Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. TABLE OF CONTENTS Installation Instructions 3 Wiring Diagram 4 Troubleshooting Table 5 Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware for your vehicle and that you carefully review the install guide.
Toyota Venza With JBL 2015-2016 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on the next page from aftermarket radio main harness to the TO2 T-harness and match the wire functions. • Remove the factory radio. STEP 2 • If the vehicle is equipped with an OEM backup camera, connect the TO2 T-harness to the backup camera harness. STEP 3 • Connect the factory harness to the TO2 T-harness.
Toyota Venza With JBL 2015-2016 WIRING DIAGRAM with an Amplifier STEP 5 STEP 1 WHITE WHITE/BLACK GRAY GRAY/BLACK GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Venza With JBL 2015-2016 TROUBLESHOOTING TABLE PROBLEM SOLUTION When a button on the steering wheel is pressed, the light on the Maestro module blinks but the radio does not respond. Ensure the blue 4-pin steering wheel control cable is connected between the maestro and the radio (the radio will use either the 3.5mm jack or the Blue/ Yellow wire, not both). Refer to radio’s owners manual to verifie if the radio has this function: Steering Wheel Control (ON/OFF) : choose ON.
INSTALL GUIDE 2013-2014 Toyota Venza With JBL and Nav RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-TO2 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-AS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician.
Toyota Venza With JBL and Nav 2013-2014 WELCOME Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features.
Toyota Venza With JBL and Nav 2013-2014 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on the next page from aftermarket radio main harness to the TO2 T-harness and match the wire functions. • Remove the factory radio.
Toyota Venza With JBL and Nav 2013-2014 WIRING DIAGRAM with an Amplifier STEP 5 STEP 1 WHITE WHITE/BLACK GRAY GRAY/BLACK GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Venza With JBL and Nav 2013-2014 TROUBLESHOOTING TABLE PROBLEM SOLUTION When a button on the steering wheel is pressed, the light on the Maestro module blinks but the radio does not respond. Ensure the blue 4-pin steering wheel control cable is connected between the maestro and the radio (the radio will use either the 3.5mm jack or the Blue/ Yellow wire, not both). Refer to radio’s owners manual to verifie if the radio has this function: Steering Wheel Control (ON/OFF) : choose ON.
INSTALL GUIDE 2015-2016 Toyota Venza Without JBL RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface iDatalink Maestro HRN-RR-TO2 Installation Harness PROGRAMMED FIRMWARE ADS-RR(SR)-TOY02-AS ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician.
Toyota Venza Without JBL 2015-2016 WELCOME Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. TABLE OF CONTENTS Installation Instructions 3 Wiring Diagram 4 Troubleshooting Table 5 Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware for your vehicle and that you carefully review the install guide.
Toyota Venza Without JBL 2015-2016 INSTALLATION INSTRUCTIONS STEP 1 • Unbox the aftermarket radio and locate its main harness. • Cut and remove the front speaker wire junction connectors. • Connect the wires shown on the next page from aftermarket radio main harness to the TO2 T-harness and match the wire functions. • Remove the factory radio. STEP 2 • If the vehicle is equipped with an OEM backup camera, connect the TO2 T-harness to the backup camera harness.
Toyota Venza Without JBL 2015-2016 WIRING DIAGRAM without an Amplifier STEP 5 STEP 1 CUT AND REMOVE THE SPEAKER WIRE JUNCTION CONNECTORS WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Toyota Venza Without JBL 2015-2016 TROUBLESHOOTING TABLE PROBLEM SOLUTION When a button on the steering wheel is pressed, the light on the Maestro module blinks but the radio does not respond. Ensure the blue 4-pin steering wheel control cable is connected between the maestro and the radio (the radio will use either the 3.5mm jack or the Blue/ Yellow wire, not both). Refer to radio’s owners manual to verifie if the radio has this function: Steering Wheel Control (ON/OFF) : choose ON.
