SELECT VEHICLE PRINT PAGES NEEDED HOW TO USE THIS INSTALL GUIDE 1 Open the Bookmarks menu and find your vehicle OR scroll down until you find the install guide for your vehicle. 2 Print only the pages for your vehicle using the advanced options in the Print menu. 3 Install your Maestro RR according to the guide for your vehicle. WARNING Pressing the printer icon or “quick printing” this document will print all of the guides in this compilation. NOTICE: Automotive Data Solutions Inc.
INSTALL GUIDE 2014-2018 Jeep Cherokee RETAINS STEERING WHEEL CONTROLS, VEHICLE SETTINGS, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR Radio Replacement Interface iDatalink Maestro CHK1 Dash Kit E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-CHR03M-DS ADDITIONAL RESOURCES ACC-SP1 Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
Jeep Cherokee 2014-2018 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Installation Instructions 3 Wiring Diagram 6 Radio Wire Reference Chart 7 Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware for your vehicle and that you carefully review the install guide.
Jeep Cherokee 2014-2018 INSTALLATION INSTRUCTIONS FACTORY RADIO DISASSEMBLY / DASH KIT ASSEMBLY STEP 1 • Pry out the climate panel to expose the two (2) screws that hold in the radio bezel. Disconnect the climate panel harness and put to the side. (Fig. 1.1, 1.2) Fig. 1.1 Fig. 1.2 Fig. 1.3 Fig. 1.4 Fig. 1.5 Fig. 1.6 Fig. 1.7 Fig. 1.8 STEP 2 • Remove the two (2) screws and remove the radio bezel. (Fig. 1.
Jeep Cherokee 2014-2018 INSTALLATION INSTRUCTIONS FACTORY RADIO DISASSEMBLY / DASH KIT ASSEMBLY MAKE CONNECTIONS STEP 9 STEP 13 • Plug connectors (J) and (K) to CHK1 media hub as shown. • At the front of the center console, pry off the plastic cover. (Fig. 2.1) • Plug connector (L) from rear of vehicle to long USB adapter (included in the kit) then to aftermarket radio. STEP 10 STEP 14 • Using a plastic pry tool, lift and detach the center console cover to expose the media port at the front. (Fig.
Jeep Cherokee 2014-2018 INSTALLATION INSTRUCTIONS • Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (If there is no iDatalink audio input, connect to AUX). Note: On Pioneer radio, ensure that there is nothing plugged into the W/R port. • Plug mini USB cable to short USB adapter then connect adapter to aftermarket radio. • Plug long USB adapter to aftermarket radio.
Jeep Cherokee 2014-2018 WIRING DIAGRAM STEP 17 STEP 14 WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
Jeep Cherokee 2014-2018 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A N/A VS
Jeep Cherokee 2014-2018 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work / show up. Make sure that you selected Gauges during the flash. Reset the RR. When making a phone call you cannot hear the callers but they can hear you. If your vehicle has a factory amplifier, make sure that the 4-pin green and white connectors in the harness are plugged in correctly, as stated in step 15. The radio stays ON or the radio doesn’t come ON at all.
INSTALL GUIDE 2019 JEEP CHEROKEE RETAINS STEERING WHEEL CONTROLS, VEHICLE SETTINGS, AND MORE! OR PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR Radio Replacement Interface iDatalink Maestro CHK1 Dash Kit E L E C T R O N I C S Click here for: Radar Installation Guides PROGRAMMED FIRMWARE ADS-RR(SR)-CHR03M-DS ADDITIONAL RESOURCES ACC-SP1 Maestro RR2 Programmable Outputs Guide NOTICE: Automotive Data Solutions Inc.
JEEP CHEROKEE 2019 WELCOME TABLE OF CONTENTS Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Installation Instructions 3 Wiring Diagram 5 Radio Wire Reference Chart 6 Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct firmware for your vehicle and that you carefully review the install guide.
JEEP CHEROKEE 2019 INSTALLATION INSTRUCTIONS FACTORY RADIO DISASSEMBLY / DASH KIT ASSEMBLY STEP 1 • Pry out the climate panel to expose the two (2) screws that hold in the radio bezel. Disconnect the climate panel harness and put to the side. (Fig. 1.1, 1.2) Fig. 1.1 Fig. 1.2 Fig. 1.3 Fig. 1.4 Fig. 1.5 Fig. 1.6 Fig. 1.7 Fig. 1.8 STEP 2 • Remove the two (2) screws and remove the radio bezel. (Fig. 1.
JEEP CHEROKEE 2019 INSTALLATION INSTRUCTIONS MAKE CONNECTIONS • Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (If there is no iDatalink audio input, connect to AUX). STEP 9 Note 1: On Pioneer radio, ensure that there is nothing plugged into the W/R port. • Unbox the aftermarket radio and locate its main harness. • Connect the wires shown on the next page from aftermarket radio main harness to the CHK1 T-harness and match the wire functions.
JEEP CHEROKEE 2019 WIRING DIAGRAM STEP 13 STEP 9 WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) GRAY/BLACK - RF SPEAKER (-) GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP.
JEEP CHEROKEE 2019 RADIO WIRE REFERENCE CHART Wire Description Polarity Wire Color on Maestro T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Wire Color on Sony cable Illumination (+) Orange N/A Orange/White Orange/White Orange Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A N/A VSS (ve
JEEP CHEROKEE 2019 TROUBLESHOOTING TABLE PROBLEM SOLUTION Gauges do not work / show up. Make sure that you selected Gauges during the flash. Reset the RR. When making a phone call you cannot hear the callers but they can hear you. If your vehicle has a factory amplifier, make sure that the 4-pin green and white connectors in the harness are plugged in correctly, as stated in step 15. The radio stays ON or the radio doesn’t come ON at all.