Installation Instructions

ManualsBrandsIDEAL INDUSTRIES ManualsElectricalIDEAL®120' Tuff-Grip™ Fish Tape

• Every non-conductive fish tape is “Proof Tested’‘ to assure superior pulli

strength and proudly boasts a 5-year limited warranty on the crimped co

tions.

• Replacement winders for IDEAL S-Class

are the same as for the IDEAL

Fish

: LB-195 winder for 12" case.

Accessories

Instructions for IDEAL Gold-Fish

Fish Tape Leader and Fis

Tape Ball:

1. Unscrew end cap (LB-221 Adapter)

from Leader.

2. After cutting off loop on fish tape,

slide fish tape through hole in adapter.

3. Heat end of fish tape to a dull red and bend

with pliers. Flatten end of tape while still

red. Reheat if necessary.

4. Allow tape to cool. DO NOT QUENCH.

5. Reassemble adapter to leaded and tighten.

Pull on fish tape to ensure tape is secure

in adapter.

Follow the same instructions as above for Fish Tape Ball.

Instructions for IDEAL S-Class

Non-Conductive Fish Tape:

Important:

Nylon/fiberglass tape.

WARNING: Do not bend IDEAL S-Class

Fish Tape smaller than a

3" radius or tape will break.

• Beware, and take heed of the cautions associated with this class of fish tape.

1) DO NOT EXCEED A MINIMUM BENDING RADIUS OF THREE (3) INCHES

or tape will fracture.

2) DO NOT GRASP THE TAPE WITH ANY TYPE OF MECHANICAL PULLING

TOOL or tape will be damaged and fracture.

3) When pulling the IDEAL Tape-Pak

Case, DO NOT allow tape to bend

at 90° to winder. Keep IDEAL Tape-Pak

and conduit opening in a

straight line.

• DO NOT pull IDEAL S-Class

Fish Tape with any type of mechanical fish tape

puller. They will severely damage the tape. Use IDEAL S-Grip

S-Class

Fish

Tape Puller (Catalog #31-170) for pulling this tape and extend the useful life of

this tape.

• Five-year limited warranty on IDEAL S-Class

Fish Tape to leader and tape to

eyelet connection. Simply return broken pieces to IDEAL. Warranty limited

solely to repair or replacement of eye or leader; no warranty of merchantability,

fitness for a particular purpose or consequential damages. Warranty does not

cover broken tape.

• The crimped connections refer to the connector at the point the fish tape is

joined to the eyelet, or the leader, or the leader to the eyelet. If failure occurs

within the five-year period (the tape pulls out of the eyelet or leader), IDEAL

will install a new connector on the fish tape at no charge. IDEAL will not

replace the entire fish tape.

• Caution: IDEAL S-Class

Fish Tape does not act like steel tape and can get

twisted or knotted, similar to a garden hose. If this occurs, caution must be

taken to carefully untangle. Remember, the warranty only covers the crimped

connections, not the tape itself.

• Always keep your fish tape wound on its reel when not in use. This protects the

tape and reduces the chance of tripping or accidental contact with energized

equipment.

• Coiled tape is under tension–do not open reel with the tape coiled.

• The use of safety glasses is recommended when using this product.

• When making pulls, do not pull directly towards you. Pulling to one side will

reduce the chance of injury if the force required to pull the tape suddenly

reduces.

• Replace IDEAL Tape-Pak

, IDEAL Rapid-Pak

and IDEAL Tape-Pak

XL-15

storage reels or winder that has become chipped, cracked, or otherwise damaged.

Instructions for IDEAL Flat Spring Steel Fish Tape:

Important:

• Hold flat steel tape coil firmly when removing retaining ties or bands to prevent

rapid uncoiling and possible injury. Uncoil slowly.

• To reform pulling loop, heat spring steel fish tape to a dull red and bend by

grasping the free end with pliers. Allow to air cool only. DO NOT QUENCH.

Instructions for IDEAL Gold-Fish

Flexible Wound Wire Fish Tape:

• 31-402 Coil-Flex fish tape replaced with 31-143.

Tape damaged or abused will have properties less than 500 lbs.

• IDEAL Gold-Fish

Replacement Handles:

31-143 handle LB-194

31-144 handle LB-195

31-145 handle LB-195

General Information applying to all fish tapes:

Important Safeguards:

Metallic Fish Tape.

WARNING:Do not use near electrically live equipment. Electrical

shock may occur.

• Always route wires to be pulled through eyelet pulling loop, twisting back over

wires to form a closed loop. Wrap eye (loop) and wire bundle securely with

plastic tape to prevent separation during pulling. Or use IDEAL Squid

Multi-

Wire Pulling Leader.

• Protect yourself against the possibility of falling should the wires free up or

separate from the pulling loop or eye.

• Do not grab the fish tape with pliers or other tools which may kink, damage or

weaken the tape.

• Avoid pulling fish tape over sharp edges which may damage the tape.

• Inspect fish tape prior to each use. Do not use nicked, corroded or otherwise

damaged fish tape which may be weakened and break during pulling.

• Do not use on power pulling equipment which could damage or break tape.

• For fish tape not contained in reels, grasp coil firmly and remove retaining ties

or bands. Insert pulling loop in conduit opening. Push tape into conduit,

uncoiling as tape is fed.

• For fish tape in reels, unwind tape as it is fed into conduit.

• The use of wire-pulling lubricant such as IDEAL Yellow 77

Plus is recom-

mended to reduce the effort required to pull the wires through the conduit and

reduce the chance of damaging the wires due to excessive pulling force.

• Remove obstructions or obstacles which could be a potential trip hazard before

pulling the fish tape back through the conduit.

• Do not attempt to force a pull that has become hung up. It is best to remove

the wire and check for obstructions.

• Never attempt to make a cold bend to form a pulling loop on the end of a steel

fish tape.

ND 853-2 Fish Tape Operators Ma 1/8/07 1:36 PM Page 2