BK1216 Template and installation instructions The BK1216 handle set is designed for the US market. It replaces handle with 4 posts and a distance of 3.228" between the handle center and the key cylinder center. For Canadian market sets with 3 posts and 3.715" distance, use SK1215. Check your current handle before installing. Warning: Check door profile prior to installation. You will require a profile wide enough for proper installation.
B. Template Placement and Drilling Instructions 1. Fold the template on the dotted line to 90 according to the handedness (left or right). 2. With the door in closed position, place folded template on inside of door so that the SIDE A is against the jamb or metal z-bar, which ever projects out farther; and SIDE B is on the inside surface of door. See Fig 1 3. Use a center punch to mark the position of all holes on SIDE A and SIDE B. 4. Drill pilot holes on all marked locations using drill bit of 1/16".
C. Handle & Latch Installation 1. Rotate the outside handle to the left or right according to your door handedness. 2. Insert a handle spindle completely into the center hole of the outside handle from the back side. The spindle locks the handle in place and actives spring. 3. Place the outside handle assembly on door. (If your door thickness is not standard then: The spindle should project through inside of door a max of 3/8" and min of 1/4". You may have to cut off spindle.) 4.
E. Drilling template E. Gabarit de perçage Print out this sheet at 1:1 scale Imprimez cette page à l'échelle 1:1 ligne de découpage 1.750in 44.5mm ligne de découpage 1/16" 8 PLCS .438in 11.1mm 2.520in 64mm .962in 24.4mm .314in 8mm 4 PLCS 3.228in 82mm 1.156in 29.4mm 1.750in 44.5mm Thank you for your purchase. If you require any information or installation assistance, please contact our customer service department. Tel: 1-800-361-2236 e-mail: info@idealinc.
RFQSK1215 SK1215 Template and installation instructions SK1215 GABARIT ET INSTRUCTIONS D'INSTALLATION Warning: Check door profile prior to installation. AVERTISSEMENT : Vérifiez le profil de la porte avant l'installation. Determine if your storm door is hinged right or hinge left for proper use of drilling template. Déterminer si les charnières de la contre-porte sont à droite ou à gauche pour utiliser correctement le gabarit de perçage. You will require a profile wide enough for proper installation.
B. Template Placement and Drilling Instructions 1. Fold the template on the dotted line to 90 according to the handedness (left or right). 2. With the door in closed position, place folded template on inside of door so that the SIDE A is against the jamb or metal z-bar, which ever projects out farther; and SIDE B is on the inside surface of door. See Fig 1 3. Use a center punch to mark the position of all holes on SIDE A and SIDE B. 4. Drill pilot holes on all marked locations using drill bit of 1/16".
C. Handle & Latch Installation 1. Rotate the outside handle to the left or right according to your door handedness. 2. Insert a handle spindle completely into the center hole of the outside handle from the back side. The spindle locks the handle in place and actives spring. 3. Place the outside handle assembly on door. (If your door thickness is not standard then: The spindle should project through inside of door a max of 3/8" and min of 1/4". You may have to cut off spindle.) 4.
E. Drilling template E. Gabarit de perçage Print out this sheet at 1:1 scale Imprimez cette page à l'échelle 1:1 ligne de découpage 1.093in 27.8mm ligne de découpage 1/16" 8 PLCS .438in 11.1mm 2.520in 64mm .962in 24.4mm .314in 8mm 4 PLCS 3.715in 94.4mm 1.156in 29.4mm 1.750in 44.5mm Thank you for your purchase. If you require any information or installation assistance, please contact our customer service department. Tel: 1-800-361-2236 e-mail: info@idealinc.