Installation Guide

ManualsBrandsIDEAL Security ManualsTools & HardwareDeluxe White Storm Door Handle Set with Deadbolt

1.750in

44.5mm

1.750in

44.5mm

3.715in

94.4mm

1/16"

8 PLCS

1.156in

29.4mm

1.093in

27.8mm

.962in

24.4mm

.438in

11.1mm

2.520in

64mm

.314in

8mm

4 PLCS

.877in

22.3mm

.064in

1.6mm

2 PLCS

SK1215 Template and installation instructions

Warning:

Check door profile prior to installation.

You will require a profile wide enough for proper installation.

With the door closed, the minimum outside and inside door profile width is 1-7/8” from the edge of the door frame (glass side) to

the edge of the door jamb or metal door frame (z-bar), which ever is narrower.

Determine if your storm door is hinged right or hinge left for proper use of drilling template.

From outside of door, looking in, if the hinges are on your left, your door is left handed.

If the hinges are on the right, it is a right handed door.

Ensure that the inside paddle does not interfere with the prime door lock.

cutting linecutting line

RFQSK1215

PAGE 1 OF 4

Summary of content (5 pages)

PAGE 1
RFQSK1215 SK1215 Template and installation instructions Warning: Check door profile prior to installation. You will require a profile wide enough for proper installation. With the door closed, the minimum outside and inside door profile width is 1-7/8” from the edge of the door frame (glass side) to the edge of the door jamb or metal door frame (z-bar), which ever is narrower. Determine if your storm door is hinged right or hinge left for proper use of drilling template.
PAGE 2
Template Placement and Drilling Instructions 1. Fold the template on the dotted line to 90 according to the handedness (left or right). 2. With the door in closed position, place folded template on inside of door so that the SIDE A is against the jamb or metal z-bar, which ever projects out farther; and SIDE B is on the inside surface of door. See Fig 1 3. Use a center punch to mark the position of all holes on SIDE A and SIDE B. 4. Drill pilot holes on all marked locations using drill bit of 1/16".
PAGE 3
SPINDLES AND SCREWS SELECTION CHART HANDLE SPINDLE SELECTION LATCH SCREW SELECTION DOOR THICKNESS DOOR THICKNESS 1" 1" 1 1/4" 1 1/4" 1 1/2" 1 3/4" 1 1/2" 2" 1 3/4" 2 1/8" 2" 1. Print out this sheet using 1:1 scale. 2. Over lay screws on top of the image. 3. Select the screws that match your door thickness. 2 1/8" Now the latch screws are selected and ready for installation. ALIGN CAP OF SPINDLE HERE 1. Print out this sheet using 1:1 scale. 2. Over lay handle spindle on top of the image. 3.
PAGE 4
tapping screws Handle & Latch Installation 1. Rotate the outside handle to the left or right according to your door handedness. 2. Insert a handle spindle completely into the center hole of the outside handle from the back side. The spindle locks the handle in place and actives spring. 3. Place the outside handle assembly on door. (If your door thickness is not standard then: The spindle should project through inside of door a max of 3/8" and min of 1/4". You may have to cut off spindle.) 4.
PAGE 5
.255in 6.5mm 2.886in 73.3mm 1.926in 48.9mm 3.687in 93.7mm 1.125in 28.6mm .872in 22.2mm 2.495in 63.4mm 1.750in 44.5mm 8.550in 217.2mm .694in 17.6mm 3.720in 94.5mm 2.724in 69.2mm .875in 22.2mm 1.161in 29.5mm 1.394in 35.4mm SK1215 DIMENSIONS 2.447in 62.2mm 1.750in 44.5mm 1.246in 31.6mm 1.156in 29.4mm .675in 17.1mm 2.749in 69.8mm 2.510in 63.