Instructions / Assembly

TELEPHONE AUTO DIALER
DESCRIPTION OF COMPONENTS
1. Antenna Jack
2. Antenna
3. LCD Display
4. Speaker
5. REC./Play LED
6. Battery Low LED
7. Power LED
8. Numeric Keypad
9. MIC
10. To wall Jack
11. To Telephone
12. DC 9V Jack
13. Battery Cover
14. Reset button
15. Buzzer
16. Input Terminal
FEATURES
• Receives signals from wireless sensors - activates
Telephone auto-dialer and alarm
• Room monitor by telephone function
• Programmable voice message for telephone alert
• ARM or DISARM system by telephone
• Programmable password
• Entry delay timing (set time for how long after trigger event
before the auto dialer will dial out and siren will sound)
• Up to 5 emergency telephone numbers (up to 32 digits
each) (only last 16 digits appear on LCD screen)
• Programmable auto dialing cycle (number of times the
auto dialer will dial each programmed phone number)
up to 5 cycles
• Built-in 105 dB alarm (with programmable alarm on/off)
• HOME mode function (auto dialer will chime but not dial
out when sensors are triggered) 16 Digit, large number
display
• 10 zone icons for easy differentiation of sensor locations
• Zone 1 - 8: Can link one wireless sensor to each zone
• Zone 9: Can link up to 8 wireless sensors
• REMOTE zone: Can link up to 8 remote controls
• Recordsthevemostrecenttriggeredalarms
• Built-inashmemorytoprotectsystemdataduringa
power failure. If the battery dies, all info will remain in auto
dialer except the date and time.
• Battery Low indicator. We recommend that the battery
in the dialer be changed at least once per year, as you
change your smoke detector battery.
• Wired sensor input terminal (to connect Ideal’s wired
window and door contacts SK619)
• AC adaptor and 9V battery back-up (included)
• Wall mountable (screws and anchors included)
INSTALLATION
NOTE: The Dialer Unit must be installed where it has access to a land line and an electrical outlet.
• Install 9V battery included (Fig 1). The battery installed in this unit is a back-up battery only. This battery will keep the unit
working for a limited time during a power failure.
• Position the antenna vertically (straight up) for better reception. (Fig. 2)
• Connect the included phone cord to the jack on the control unit labeled “LINE”. Connect the other end of the cord to your
wall jack. (Fig. 3a)
NOTE:IfyouareusingaDSLservice,aDSLltermustbeinstaledbetweentheautodialerandthewalljack.
• A phone can be connected to the unit using the “TEL” jack. (Fig. 3a) Check to see if you have a dial tone.
• Connect the AC adaptor to the DC 9V jack on the auto-dialer. (Fig. 3b)
Thank you for choosing Ideal Security’s Home Security System with Telephone Auto Dialer. If you have any questions,
problems or comments regarding the installation or operation of this system, please do not hesitate to contact IDEAL’s
customer service department through our web site at www.idealalert.ca, via email at [e-mail], or by calling our
toll free number at 800-361-2236 x 230. Normal business hours 7:30 AM to 3:00 PM Eastern time. Monday to Friday.
Occasionally instructions have errors or omissions, please check for updates to these instructions, security tips and
other valuable information at www.idealalert.ca
THIS PACKAGE INCLUDES:
• 1 AUTO DIALER
• 2 REMOTE CONTROLS
• 2 WINDOW / DOOR CONTACTS
• 1 MOTION SENSOR
• 1 INDOOR/ OUTDOOR SIREN WITH LED STROBE
• ALL BATTERIES AND AC/DC ADAPTERS.
NOTE: BEFORE PERMANENTLY INSTALLING ANY OF THE DEVICES INCLUDED IN THIS PACKAGE PLEASE TEST
THE RANGE OF ALL UNITS TO MAKE SURE THAT THE RECEIVER PICKS UP ALL THE SENSORS.
NOTE: THE TELEPHONE DIALER REQUIRES AN ELECTRICAL OUTLET AND A TELEPHONE LAND LINE
WITH TONE DIALING TO MAKE OUTGOING CALLS.
SETUP OVERVIEW
• Set your passcode (refer to AUTO-DIALER SET-UP section 1)
• Program telephone numbers (refer to AUTO-DIALER SET-UP setting section 4)
• Recordyournoticationmessage(refertoAUTO-DIALERSET-UPsettingsection2)
• Install Door/Window sensors (refer to INSTALLATION OF SENSORS section)
• Install Motion sensors (refer to INSTALLATION OF SENSORS section)
It’s done!
You can now activate the system and be protected with this simple, effective wireless security system with auto dialer.
NOTE: you can change the default settings and expand the system
by following the detailed instructions provided in this manual.
IMPORTANT SAFETY TIPS
1. Do not install the system where it will be exposed to direct sunlight or rain.
2. The built-in siren is very loud, never put the system close to your ear.
3. The system should be installed away from heat sources such as radiators, heating ducts and stoves.
4. If the system sounds at random, it is possible that the installed location is too close to a heat source, changing the location
or direction of the unit may correct the problem.
5. The system can provide valuable protection for your home and property if utilized properly. However, this unit cannot
guarantee complete protection against burglary or property damage. Therefore, we will not be responsible for any losses or
damages which may occur, while using this product.
ANSWERING MACHINES AND REMOTE COMMUNICATION.
If you intend to use the REMOTE ACTIVATION features (controlling the alarm unit remotely) of the Auto Dialer, you cannot
use an answering machine.
To use the remote activation feature: Set the auto dialer to respond (pick up) before your answering machine responds. For
example, if your answering machine is set to pick up after 5 rings then set the auto dialer to pick up after 3 rings, this way
yourAUTODIALERwillpickuprst,allowingyoutoenteryourkeyselection.Completeinstructionsonsettinguptheremote
activation follow.
If the answering machine is required, then the REMOTE ACTIVATION feature cannot be used.
Set the auto dialer to respond after your answering machine normally responds (set it to 10 rings) this will ensure that the
answeringmachineisrsttorespond.
OPEN
121110
15
14
13
16
TEL.LINE