Instructions / Assembly

• PressARM/DISARM buttontoconrm.
• You are now ready to program up to 5 emergency telephone numbers. Press the */UP or #/DOWN buttons to select
memory location from 1 to 5. If you select 2 this is where your number will be stored and it will be the 2nd number dialed.
• Enter the telephone number you would like to store, as you would normally dial it in your area (maximum of 32 digits, the
screenwillonlydisplaythelast16digits),followedbyARM/DISARMtoconrm.
• Repeat steps for the four other numbers you may wish to store.
• Press PROG button eight (8) times to exit the set-up mode.
5. TO DELETE A TELEPHONE NUMBER FROM MEMORY
• Enter password followed by PROG button twice (2).
• “MEMORY”willashontheauto-dialerscreen.
• PressARM/DISARM buttontoconrm.
• Press */UP or #/DOWN buttons to select the number you want to delete.
• Press DEL./PAUSE button to delete the number.
• PresstheARM/DISARMbuttontoconrm.
• Press PROG button eight (8) times to exit the set-up mode.
6. PAUSE FUNCTION
The “PAUSE” function can be stored as one digit in the telephone number memory for some dialing operations. Every one
PAUSE in the memory dialing sequence will pause for 3.6 seconds. For example, if you want to store telephone number
514-363-1030 EXTENSION 230 to memory location 2, the operation will be as following:
• Enter password then press PROG button twice (2).
• “MEMORY”willashontheauto-dialerscreen.
• PressARM/DISARMbuttontoconrm.
• Press */UP or #/DOWN button to select memory location 2.
• Enter 5143631030 press and hold DEL./PAUSE for 2 seconds until the letter F appears on the screen, then enter 230.
• PressARM/DISARMbuttontoconrm.
• Press PROG button eight (8) times to exit set-up mode.
7. TO PROGRAM AUTO CALL FUNCTION ON/OFF
The auto-dialer has been factory pre-set with the call option ON.
If you do not want the auto dialer to call out change this to OFF:
• EnterpasswordfollowedbyPROGbuttonve(5)times.
• The “
”iconwillashontheauto-dialerscreen.
• PressARM/DISARM buttontoconrm.
• Using*/UPor#/DOWNbuttonstoselectcallOFFfollowedbytheARM/DISARMbuttontoconrm.
• PressPROGbuttonve(5)timestoexittheset-upmode.
8. TO PROGRAM AUTO DIALING CYCLE (how many times the auto dialer will call the programed numbers).
The auto-dialer has been factory pre-set to auto dial for 1 cycle (When a sensor is triggered the auto dialer will call all stored
numbers 1 time). You can change the number of cycles from 1 to 5 dialing cycles.
• Enter password followed by PROG button six (6) times.
• “CYCLE”willashontheauto-dialerscreen.
• PressARM/DISARMbuttontoconrm.
• Using */UP and #/DOWN buttons to select number of cycles between 1 and 5
followedbytheARM/DISARMbuttontoconrm.
• Press PROG button four (4) times to exit set up mode.
9. TO TEST MEMORY DIALING
In standby mode, press and hold the PROG button for at least 3 seconds, you will hear a short beep. Key in the memory
locationofthetelephonenumber,i.e.1–5.Thetelephonenumberstoredinspeciedmemorylocationwillautomaticallybe
dialed. Press the PROG button to stop the dialing. The auto dialer must be connected to a land line in order for this function
to work. If not connected then you will hear 4 short beeps.
( Fig. 3a )
TEL.LINE
( Fig. 3b )
DC 9V Adaptor
TEL.
LINE
• Wall mount option: Choose a suitable location where you have access to a telephone line and electrical outlet, drill holes,
using template provided and install anchors and screws. Place the auto-dialer over the screws and slide it down
to secure it in place.
AUTO-DIALER SET-UP
NOTE: If no key is pressed for 20 seconds, the auto-dialer will automatically exit set-up mode.
• Set-up is done in DISARM mode only.
• The auto-dialer has a factory preset password of 0-0-0. This should be changed to your own personal password.
1. TO CHANGE PASSWORD
• Enterfactorypre-setpassword0-0-0.PressPROGbuttononce(1),PASSWORDwillashontheauto-dialerscreen.
• PresstheARM/DISARMbuttontoconrmthatyouwanttoenterthePASSWORD.
• EnteryournewpasswordthenpresstheARM/DISARMbuttontoconrmyourpasswordhasbeenstored
(you can choose from 3 to 6 digits for your password).
• Press the PROG button nine (9) times to exit set-up mode.
NOTE: PASSWORD RESET
If you forget your password, locate the RESET button on the back of the unit. Press and hold the PROG button, and, press
and release the reset button once. The screen will go blank. When screen returns let go of the PROG button. You now have
the factory pre-set password of 0-0-0. This will reset the password ONLY, all other information will remain (programmed
telephone numbers and learned sensors)
2. RECORD PERSONALIZED NOTIFICATION MESSAGE
Youcanrecordasinglepersonalized20secondmessagethatwillbeplayedbackwhenyoureceivetelephonenotication
that your system has been triggered. To help remember the options you have, your message should be similar to:
“[Your name’s] security system has been triggered, please enter a command; to Monitor Room press 1 plus #, to Broadcast
press 2 plus #, to End Call press 3 plus #, to Disarm System and end call press 6 plus #.”
• Enter password then press REC/PLAY once.
• Clearly and slowly dictate your 20 second message.
• Press REC/PLAY to end recording. The recording will automatically end after 20 seconds. The message will replay once
afterrecordingisnished.
• Press REC>/PLAY to replay message at anytime.
3. SETTING THE TIME (YEAR / MONTH / DATE / HOUR / MINUTES)
• Enter password then press the PROG button nine (9) times.
•
Willashontheauto-dialerscreen.
• PressARM/DISARM buttontoconrm.
• Thedatewillshowontheauto-dialerscreenasvesetsofnumbers:year,month,anddatefollowedbythetimehourand
minutes(24hr.timeclock).Therstsetofnumberswillashconrmingthatthesecannowbechanged.
• Enter correct year by pressing */UP or #/DOWN button, then press the ARM/DISARM button. The next set of numbers will
startashing,enterthemonthbypressing*/UPor#/DOWNbutton,thenpresstheARM/DISARMbutton.Continueuntil
you have the correct date and time.
• Press PROG button once (1) to exit set-up mode.
4. TO PROGRAM EMERGENCY TELEPHONE CALL NUMBERS
• Enter password followed by PROG button twice (2).
• MEMORYwillashontheauto-dialerscreen.