Instructions / Assembly

• The detection range (left to right) is 110 degrees for a distance up to 8m (16').
• Test the area requiring coverage before mounting the sensor permanently.
• Use the swivel wall mount bracket to mark the mounting location, drill holes and install anchors and attach the bracket
with the screws provided. Slide the main unit onto the bracket until it clicks into place (Fig 5). Adjust the bracket to obtain
the best coverage of the intended protected area (Fig 6).
The Motion Sensor included with this kit is factory linked to the auto dialer
1.5~2m
(5’~6’)
5~8m (16~26’)
110°
(Fig. 6)
(Fig. 5)
BATTERY LOW INDICATOR
Whenthebatteryislow,theLEDonthefrontoftheunitwillashon3secondsandoff1second.Replacethebattery
immediately to maintain proper detection. If batteries are low they may send a false signal to the auto-dialer. Batteries in all
units should be replaced at least once per year like your smoke detectors.
DOOR/WINDOW SENSORS WITH VIBRATION DETECTION
1
2
3
4 5
6
7
8
Description of Components
1. Trigger/ battery low LED 5. Magnetic contact
2. Alarm speaker 6. Alignment arrows
3. Antenna 7. Alarm ON/OFF switch
4. Wired contact 8. Battery compartment
Installation
• Install the 9V battery (included) into the two door and window sensors (Fig. 7).
(Fig. 7)
• These two sensors are factory linked to zone 2 and 3. When one of the sensors
istriggeredeitherzone2orzone3willashonthescreen.
• Determine appropriate location for the contacts on the door or window to be protected.
• Mount the wired portion of the contact to the door or window frame and the
magnetic contact portion to the door or window.
• For maximum vibration detection the sensor should be mounted on or as close to the frame of the door or window as
possible.Beforeusingthedoublesidedtapeprovided,alignthe2sensorportionssothattheyareushandwiththe
alignment arrows facing each other and no more then 1/4" apart. Make sure to extend the antenna on the sensor for the
best transmission range.
• The Door/Window Sensors have built-in 105 dB alarms which will sound for one 10 second burst when the contacts
have separated or the detector senses vibration. This feature can be controlled with the ALARM ON/OFF switch
on the side of the unit.
BATTERY LOW INDICATOR
Whenbatteriesarelow,theLEDonthefrontoftheunitwillashon3secondsandoff1second.Replacethebatteries
immediately to maintain proper detection. If batteries are low they may send a false signal to the auto-dialer. Batteries in all
units should be replaced at least once per year like your smoke detectors.
10. TO PROGRAM CALL-IN RING DETECT CYCLE (how many rings before auto dialer will answer).
The auto dialer has been factory preset to answer after the 5th ring. The call-in ring detect cycle is for how many times you
want the phone to ring before the auto-dialer picks up. You can arm/disarm and monitor your home via the telephone.
• Enter the password followed by the PROG button seven (7) times.
• The “
”symbolwillashonthescreen.
• PressARM/DISARM buttontoconrm.
• Using the */UP and #/DOWN buttons select 3, 5, 7 or 10 (which represents the # of rings before the auto dialer picks up)
followedbytheARM/DISARMbuttontoconrm.
• Press the PROG button three (3) times to exit set-up mode.
NOTE: You cannot use an answering machine with this feature. If you want to be able to call in to the auto dialer you must
program it to answer before your answering machine does. Example if your answering machine answers after 4 rings,
you must set the auto dialer to answer at 3 rings.
11. TO PROGRAM INTERNAL 105 dB AUTO DIALER SIREN ON/OFF
The auto-dialer has been factory pre-set with the siren ON. To change this to OFF:
• Enter password followed by PROG button four (4) times.
• The “
”iconwillashontheauto-dialerscreen.(Fig.8)
• PressARM/DISARM toconrm.
• Using */UP or #/DOWN buttons to select SOUND OFF. Followed by
• ARM/DISARMbuttontoconrm.
• Press PROG button six (6) times to exit the set-up mode.
12. TO PROGRAM ENTRY DELAY TIME: (Time allowed to deactivate system once you have entered your residence)
The auto-dialer has been factory pre-set with a 20 second delay. To change the delay time to 0, 5, 10, 15 or 20 seconds:
• Enter password followed by PROG button eight (8) times.
• “ENTRY”willashontheauto-dialerscreen.
• PresstheARM/DISARMbuttontoconrm.
• Using the */UP and #/DOWN buttons select the seconds 0,5,10,15 or 20
• PressARM/DISARM toconrmthenumberofsecondsyourequirefortheentrydelaytime.
• Press the PROG button twice (2) to exit set-up mode.
INSTALLATION OF SENSORS
Before installing Sensors permanently you should test there signal range. Using HOME MODE is a convenient way to test
Sensors and Remotes. In HOME MODE the auto dialer will function only as a chime. Press the HOME button on the keypad
of the auto- dialer, wait 60 seconds at which time you will hear a beep. Then trigger the wireless sensors. The auto-dialer will
receiveasignalandachimewillsound.Ifyoudonothearachimeandthezoneisnotashingontheauto-dialerscreen,the
sensormaybeoutofrangeoftheauto-dialer.Repositioningeitherthesensororauto-dialershouldxthisproblem.Press
HOME button again to exit test mode.
MOTION SENSOR
Description of Components
1
2
3
4
1. Mounting bracket
2. Motion sensor window
3. Battery low / Trigger LED
4. Battery compartment
Installation
(Fig. 4)
• Install 9V battery (included) into the motion sensor (Fig. 4).
• The motion sensor is factory linked to zone 1. When triggered zone 1 will
ashontheautodialerscreen.