Instructions / Assembly

SYSTEM OPERATION
1. TO ARM THE SYSTEM
• Enter password followed by the ARM/DISARM button.
• Three short beeps will sound and the ARM icon will show on the auto-dialer screen.
• You can also press the ARM button on the remote control to arm the auto dialer.
• Wait 60 seconds for a short beep. The auto-dialer is now set at ARM and ready to receive signals.
• If an OPEN ZONE condition exists (a door or window is open) the auto dialer will beep for 5 seconds and the screen will
show“CLOSEPLEASE”andthezonenumberofthesensorthattriggeredthealarmwillbeashing.Ifthezoneremains
open (the door or window is not closed) after 60 seconds the alarm will sound and the auto dialer will start dialing.
2. ALARM OPTIONS
• If the auto-dialer (in ARM mode) receives a signal from any sensor, the screen will display TRIGGER with the zone
number. After the entry time delay it will sound a SIREN for 30 seconds on, 30 seconds off and 30 seconds on, and will
automatically dial all the numbers stored, one by one, for the number of cycles (amount of times the numbers are dialed)
you have chosen. The receiver of the phone call will hear a prerecorded message and will have option to listen in or
broad cast to the room the auto-dialer is located in. The receiver of the call can then call a neighbor, the police, or take
other appropriates action.
• In ARM mode, if the auto-dialer is set to SIREN OFF, the numbers stored will be dialed silently. No siren will be heard from
the auto-dialer. NOTE: The INDOOR/OUTDOOR SIREN must also be set to OFF for silent operation.
3. TO DISARM THE SYSTEM FROM THE AUTO DIALER KEY PAD
• Enter password followed by the ARM/DISARM button on the auto dialer. Or press on DISARM button on the remote.
• YouwillhearonebeepandtheARMiconwilldisappearfromtheauto-dialerscreentoconrmthattheAuto-Dialerhas
been disarmed.
• Before dialing the auto dialer will detect if a phone line is connected, if no telephone line is connected the auto dialer will
beep 4 times then the alarm will sound without dialing.
4. PANIC BUTTON
• If you press “PANIC” button on auto-dialer or remote control, the ALARM will sound instantly for 30 seconds, then off for
30 seconds, then on for 30 seconds and then off, and the auto-dialer will begin dialing the stored numbers immediately.
• To stop the alarm sound and the dialing, enter password then press ARM/DISARM button or press the DISARM
button on the remote.
5. REMOTE OPERATION BY TELEPHONE.
(What you can do when you receive a call from the system)
Answer the call. You will hear your personalized message. The message will repeat 3 times. If no function codes are entered
by the receiver of the call, the system will hang up and dial the next number programed.
Youmayenterthefollowingcodesonyourphonekeypad.Onceacodeisenteredyouwillhearabeepforconrmation.
Function Press Keys
Room Monitor 1 and #
Broadcast to room 2 and #
End of Call 3 and #
DISARM System 6 and #
6. REMOTE ACTIVATION BY TELEPHONE
(To control your auto dialer via telephone)
• Telephone your home number. The auto-dialer will answer after the designated amount of rings
that you have programmed.
• OnceconnectedenteryourPASSWORD,youwillheartwobeeps(conrmation).
• Enter key combination listed below for desired function you would like to perform.
ROOM MONITOR – Enter “1 and #” after the beep you will be able to listen into the room where the auto-dialer is installed.
After 30 seconds you will hear a beep to remind you that if you do not enter another code within 20 seconds the call will end.
The total duration of the room monitor is 50 seconds if no other codes are entered.
WIRELESS INDOOR/OUTDOOR SIREN & STROBE LIGHT
Description of Components
10
2
3
4
1
BAT.LOW AC
LEARN
DC 6V
5
6
8
97
ALKALINE
RECHARGE
10S
0S
1. Antenna
2. Arm / Battery low / Trigger indication LED ( red )
3. Strobe light
4. AC indication LED ( green )
5. Siren / Light function switch
6. LEARN button
7. Alkaline / Recharge switch
8. DC Jack
9. Entry delay switch
10. Battery cover
Installation
• Remove the screws from the battery compartment cover (Fig. 8).
A
A
A
AAA
AA
A
A
AA
ALKALINE
RECHARGE
10S
0S
(Fig. 8)
• Set the Entry delay (0 / 10 seconds) timer switch.
• Set the battery type switch.
WARNING: Failure to choose the correct setting will damage this unit.
If you use non rechargeable batteries the switch must set to ALKALINE.
If you use rechargeable batteries the switch must be set to RECHARGE.
NOTE: UNIT WILL NOT RECHARGE BATTERIES .
• Install 4 AAA batteries (included).
or 4 AAA 700mAh NI-MH rechargeable batteries (not included).
• Batteries provide Back-up power for emergency functionality in case of AC power failure.
ALKALINE
RECHARGE
10S
0S
(Fig. 9)
• Set the Siren / Light function switch.
• Temporarily remove the water resistant rubber cover to select the alarm function.
Set the switch to: Siren only / Siren+Strobe light / Strobe light only. Replace cover.
• Plug the AC adaptor to the DC 6V socket,
the AC power indication LED will show a steady light (Fig. 9).
• The Siren included with this kit is factory linked to the Auto Dialer.
WIRELESS REMOTE CONTROLS
Description of Components
1
2
3
4
1. Panic button
2. Disarm Button
3. Arm button
4. Battery compartment
Installation
Install the CR2032 battery included into the remote control (Fig. 10).
(Fig. 10)
• Remote controls for Arm, Disarm functions of the Telephone Dialer.
• Remote range from receiver is up to 25 meters (80 feet).
• The Remote Controls included with this kit are factory linked to the auto dialer.
If the remote has to be moved closer to the receiver in order to function please
replace batteries. The battery life is about six months under normal use.
NOTE: If you wish to change the factory programed zone location of the sensors
or remote controls see: LINK WIRELESS SENSORS TO THE AUTO DIALER.