Instructions / Assembly

9. BATTERY LOW LED INDICATOR
WhentheBatteryLowLEDashesonceevery1.5seconds,itindicatesthatthebatterypowerinauto-dialerisrunninglow.
Replace the batteries immediately. If batteries are low, a false signal may be triggered and the auto dialer may start dialing.
Batteries in all units should be replaced every year like your smoke detectors.
LINK WIRELESS SENSORS TO THE AUTO DIALER
All the units included in this package have been factory linked to the auto dialer. You may link additional sensors, remote
controls or sirens to your auto-dialer. In certain circumstances you may have to re-link existing parts.
You can learn a total of 16 sensors and 8 remote controls to this unit .
The system has a total of 10 zones for wireless sensors and remote controls:
• Zone 1-8: link one wireless sensor per zone, they will trigger the dialer in armed mode only.
• Zone 9: Learn up to 8 wireless sensors and they will trigger the dialer in armed mode only.
• REMOTE Zone (LCD icon REMOTE) is the remote control zone and you can learn up to 8 remote controls..
NOTE: If you wish to change the factory programed zone location of the sensors they must be deleted from their current
zone and re linked to a new zone (see instructions below)
LINKING WIRELESS SENSORS OR REMOTE CONTROLS TO THE AUTO DIALER
• Enter your password and press the PROG button three (3) times.
• The“LEARN”iconwillashonthescreen.
• PressARM/DISARM toconrm,thesystemwillgointolearningIDcodemodeandzone1iconwillash.
• Pressthe*/UPand#/DOWNbuttonstoselectthezoneyouwishtolearnyoursensorto.WhenthescreenashesNO
IDCODE,thatmeansthatzoneisemptyandyoucanlearnasensor.IfthescreenashesFULLthenyoualreadyhave
a sensor linked to that zone. You can either choose another zone or press DEL./PAUSE to delete the sensor in that zone
and link the new sensor.
• PressARM/DISARM toconrmthatthisisthezoneyouwantthesensortobelinkedwith
• Trigger the sensor or remote control that you are trying to link as follows:
 • WirelessmotiondetectorSK615,bymovinghandinfrontofsensortosendsignal(pleaseseenotebelow).
 • Wirelessdoor/windowsensorSK621&SK625,openingandclosingthemagneticswitchwillsendsignal.
 • WirelesswateralarmsensorSK616,putsensorinwatertotriggerandsendsignal.
 • WirelesstemperaturesensorSK627,bypressingthetestbutton.
 • GarageAlertSK623,openingthegaragedoorwilltriggerandsendsignal.
 • RemotecontrolSK629,pressinganykeywilltriggerandsendasignal.
• Youwillhearalongbeepfromtheauto-dialertoconrmthatlinkingwassuccessfulandthescreenwilldisplayFULLfor
zones 1-8. Zone 9 will display the number of sensors in the zone up to a maximum of 8. The Remote zone will display the
number of remote controls in the zone up to a maximum of 8.
• Press the PROG button seven (7) times to exit the setup mode.
NOTE: if you have linked a motion detector to your auto dialer, place a towel over the motion sensor before linking other
items as the motion sensor will send signal to auto- dialer every time you move.
LINK THE AUTO DIALER TO THE INDOOR/ OUTDOOR SIREN
The Siren included in this package has been factory linked to the auto dialer. To re-link the siren:
• Remove the water resistant rubber cap on the bottom of the Siren, press and hold the LEARN button, release the button
afterhearingasingleconrming“beep”,theunitisnowreadytolinkwiththeAutoDialer
• On the auto dialer enter the password then press ARM/DISARM button once.
• YouwillhearalongbeeptonefromtheSirentoconrmlinkingwassuccessful.IflinkingwasunsuccessfulYouwillhear
four short beeps. Carefully repeat the steps.
• To unlink all auto Dialers, Sensors or Remote Controls from the Siren: press and hold LEARN button for 12 seconds, you
will hear a long beep tone, all links will be deleted.
ARM SYSTEM – Enter “5 and #” after three short beeps the system is ARMED and will automatically hang up. If you hear
5 rapid beeps after three short beeps, it means one of your sensors isn’t closed or is activated. The system will give you 5
seconds to enter a new code.
DISARM SYSTEM – Enter “6 and #” after a beep the auto-dialer will DISARM and hang up.
NOTE: Whether you receive an alarm call or you call the auto dialer, if you enter a wrong password or operation code, the call
will disconnect and sound 5 beeps on the auto-dialer. If the call was an alarm call to you, you can wait for it to call you again
(providing you have set the dialing sequence to more than one cycle) and then enter the above codes again. If your dialing
sequence is set to one cycle and you have set up the auto dialer to answer before your answering machine (if you have one
connected) then you can call into the auto dialer and enter in your codes again. If you made the initial call to the dialer you
just have to redial and then enter the codes again.
7. HOME MODE FUNCTION:
While at home you can set your auto-dialer to home mode. This will activate a chime every time one of the sensors is trig-
gered. You can also program which zone will send signals to the auto-dialer when triggered. The factory default is all sensors
send signals to the auto dialer.
To activate Home Mode.
• Press the HOME button once; you will hear a chime and the word HOME will appear on the LCD screen.
• Wait 60 seconds, you will hear a beep. System is now in home mode and will chime if a sensor is triggered.
• When auto-dialer receives signal it will chime and show which zone is being triggered on the auto-dialer LCD screen. If
thePANICbuttonispressedtheautodialerwillstartdialingthenumbersprogrammedfortheamountoftimesspecied.
• Press the HOME button again to exit the home mode.
NOTE: Arming system while in Home mode will deactivate Home mode. Press the HOME button again if you want to return to
home mode. In home mode the system will not dial out or sound alarm.
Pressing the PANIC button on the keypad or remote control will trigger the alarm and start the dialing sequence.
Enabling and Disabling sensors when in home mode.
When in HOME mode all sensors will send signal to auto dialer and you will hear a chime. If you have one or more sensors
that you do not wish to activate a chime on the auto dialer you may disable the zone containing the sensor. For example, a
contact on a patio door that is in zone 3, if you disable zone 3 a chime will not sound each time the door is opened. Zone’s
1 through 8 control 1 sensor per zone allowing for individual control of 8 sensors. Zone 9 can contain up to 8 sensors all
sensors in that zone are enabled or disabled together, you cannot pick individual sensors in that zone. The REMOTE zone
cannot be disabled. The factory preset is all sensors are on and will activate a chime when triggered.
To turn off a zone follow these instructions.
• Enter password followed by pressing the Home button.
• ZoneonewillashontheLEDscreen.
• Using the */UP and #/DOWN buttons select the zone you want to change the setting for.
• PressARM/DISARM buttontoconrm,usingthe*/UP&#/DOWNbuttonsselectONorOFF.PressARM/DISARM
buttontoconrm
• Press the Home button once to exit home-setup.
8. VIEW STORED INFORMATION FUNCTION
Triggered Events History
The last 5 triggered Events, including the time the event occurred and the zone that was triggered are stored in memory.
To view triggered events,
• In standby mode, press #/DOWN button
• ThetimeandzoneoftherstrecordedtriggeredeventwillbedisplayedontheLEDscreen.See.
• Pressing the #/DOWN button repeatedly will cycle through 5 stored events ending with the most recent.
Stored Telephone Numbers
In standby mode, press */UP to view stored telephone numbers.
NOTE: If no buttons are pressed for 20 seconds, the auto-dialer will automatically exit view mode.