Instructions / Assembly

ManualsBrandsIdeal ManualsElectrical200 Amp Clamp Meter with TRMS, NCV, Shaker, CP, Backlight

#61-702

#61-704

700 Series

200 Amp Clamp Meters

1. Non-contact voltage (NCV) (#61-702)

With the NCV tab on the tip of the clamp close to an AC

voltage, press the NCV button. The NCV LED will light and

the beeper will beep. The closer the NCV tab is to AC volt-

age, the louder the beep.

To differentiate between hot and neutral in an outlet, insert

the NCV tab into each slot in the outlet. The beeper will be

much louder on the hot side of the outlet than the neutral.

Summary of content (6 pages)

PAGE 1
#61-702 #61-704 1 2 700 Series 200 Amp Clamp Meters 3 6 5 7 4 8 1. Non-contact voltage (NCV) (#61-702) With the NCV tab on the tip of the clamp close to an AC voltage, press the NCV button. The NCV LED will light and the beeper will beep. The closer the NCV tab is to AC voltage, the louder the beep. To differentiate between hot and neutral in an outlet, insert the NCV tab into each slot in the outlet. The beeper will be much louder on the hot side of the outlet than the neutral.
PAGE 2
The test lead can also be used to differentiate between the hot and neutral. Insert the rod test lead into the + port and snap it into the test probe holder. Press the NCV button and insert the probe into each slot of the outlet. The beeper will only beep on the hot side of the outlet. 7. Max button Press Max prior to a measurement to capture the maximum reading displayed during the measurement. To clear the max value, press the max button again, or press the reset button. 2.
PAGE 3
4. Visually inspect leads for damage before using. Replace if insulation is damaged or leads appear suspect. 5. Never ground yourself when taking electrical measurements. Do not touch exposed metal pipes, outlets, fixtures etc. Keep your body isolated from ground by using dry clothing, rubber shoes, mats, or any other approved insulating material. Keep your fingers behind the finger guards on the probes. Work with others. 6. Before beginning all unknown measurements, set meter to highest possible range. 7.
PAGE 4
To Measure AC Current: 1. Set the rotary switch to the appropriate AAC range. 2. With the jaws closed, separate one wire from a bundle using the long fixed jaw. 3. Slide the wire to the corner where the two jaws meet, then open the jaws to let it in. 4. Measure the current in only one wire at a time. DC Voltage Range Resolution Max Accuracy Display 2000mV 1mV 1999 ±(0.5%+1) 200V 0.1V 199.9 ±(0.5%+1) 1000V 1V 1000 ±(0.5%+1) AC & DC Volts To Measure Voltage: 5.
PAGE 5
Resistance (Ohms) Capacitance Testing Range Resolution 200Ω 0.1Ω 200kΩ 0.1kΩ Max Display 200.0 200.0 Accuracy ±(1% +3) ±(1% +3) To Measure Resistance: 1. Turn the power off to the circuit or device that is to be measured and discharge all capacitors before attempting a measurement. 2. Plug the black test lead into the COM port and the red test lead into the + port. 3. Set the rotary switch to the appropriate Ohms range. 4.
PAGE 6
Continuity Check Battery Replacement: To Verify Continuity: A continuity test ensures that all circuit connections are intact. 1. Plug the Black test lead into the COM port and the Red test lead into the + port. 2. Set the rotary switch to the position. 3. Connect the test leads to the circuit to be measured. The beeper will sound within 100mS if the resistance of the circuit measured is lower than 300 Ohms. 4. In addition to the beeper, both 61-702 and 61-704 have an LED to verify continuity.