IDEAL INDUSTRIES, INC.
TABLE OF CONTENTS Title Page Introduction 1 Precautions and Safety Information 1 Symbol Table 1 TightSight™ Display Notes 1 High Voltage Warning (HI-V) 2 Safety Information 2 Certifications and Compliance 3 Specifications 3 General Specification 3 Voltage Specifications 4 Current Specifications 4 Resistance Specifications 4 Frequency Specification 4 Capacitance Specifications 4 Continuity Specifications 4 Performance Verification 5/6 Calibration 7/8 Replacing the Battery
Page 1 Introduction Warning To avoid shock or injury, do not perform the verification tests or calibration procedures described in this manual unless you are qualified to do so. The information provided in this document is for the use of qualified personnel only. Caution The 61-760 series contains parts that can be damaged by static discharge. Follow the standard practices for handling static sensitive devices. For additional information about IDEAL INDUSTRIES, INC.
Page 2 High Voltage Warning (HI-V): The meter beeps and lights an LED when >30V AC/DC voltage is present through test leads of the meter. This enhanced safety feature alerts the user that dangerous voltage is present across the leads even if the meter is set on an incorrect function or range. Notes: This feature does not work through the clamp head as the clamp is intended to only measure current.
Page 3 Certifications and Compliances Designed to UL 61010-1 second edition, IEC 61010-2-032 second Safety edition,IEC61010-031 specifications 1000V DC Category III 600V DC Category IV Input rating 750V AC Category III 600V AC Category IV Over voltage category CAT IV: Outside and service entrance. CAT III: Distribution level mains, fixed installation. CAT II: Local level mains, appliances, and portable equipment. CAT I: Signal level, special equipment or parts of equipment, telecommunication, electronics.
Page 4 61-763 Function / Range AC Voltage (True RMS) (45-400Hz) DC Voltage AC Current (True RMS) (45-400Hz) Capacitance Frequency Resistance Continuity 61-765 Function / Range AC Voltage (True RMS) (20-400Hz) DC Voltage AC Current (True RMS) (20-400Hz) DC Current Capacitance 1 Resistance Continuity Ranges Accuracy 0.0V ~ 600.0V, 45Hz - 100Hz 600.0V ~ 750.0V, 45Hz - 100Hz 0.0V ~ 750.0V, 100Hz - 400Hz 0.0V ~ 600.0V 600.0V ~ 999.9V 0.0A ~ 660.0A, 45Hz -60Hz 1.0% + 5 digits 1.5% + 5 digits 6.
Page 5 PERFORMANCE VERIFICATIONS Perform the following analysis; if the meter conforms to the limits listed in Table 1 through 7 the meter is functioning correctly. If the meter does not conform to any of the listed limits the calibration procedure must be performed. Performance Verification Preparation 1. Turn on the calibrator, allow calibrator to warm up. Temperature stabilization should be reached after 30 minutes. 2.
Page 6 Table 6 Capacitance and Frequency Test Low Limit 49.70 High Limit 50.30 200Hz @ 10A 198.5 201.5 61-763, 61-765 60Hz @ 120V 59.2 60.8 61-763, 61-765 100µF 94.0 106.
Page 7 CALIBRATION Calibration Preparation 1. Turn on the calibrator, allow calibrator to warm up. Perform calibration at 23±2°C (73.4°F ±3.5°F) at relative humidity of < 70%. Temperature stabilization should be reached after 30 minutes. 2. Disconnect the test leads and turn the range switch to “OFF”. 3. Remove the screws holding the battery cover, one at the jaw, and the screw for the TightSight™ cover. 4.
Page 8 Resistance Calibration 1. Set the function switch to range. Short the V and COM inputs on the meter. After a reading in the LCD is settled (about 5 seconds), press MAX/MIN button until unit display reads 000.0 ± 1 digit. Zero adjustment is complete. 2. Connect the calibrator to the V and COM inputs on the meter. 3. Output 800.0 . After a reading in the LCD is settled (about 5 seconds), press MAX/MIN button until unit display reads 800.0 ± 2 digits. Adjustment is complete. 4. Output 8K .
Page 9 Battery Replacement (Refer to Figure 1) 1. Disconnect the test leads from any circuit under test and turn off meter. 2. Use a Philips head screwdriver to remove the screws on battery cover. 3. Remove battery from the battery compartment. 4. Install new 9V battery (NEDA #1604). An alkaline type is recommended. 5. Install new battery into compartment using care to install to proper polarity. 6. Reinstall battery cover.
