Datasheet

ManualsBrandsIDEC ManualsEmergency Stop SwitchesEmergency Stop Switch, 2NC, IP65

www.apem-idec.eu

D-026

ø22 XW Series Emergency Stop Switches

APEM

Switches &

Pilot Lights

Control Boxes

Emergency

Stop Switches

Enabling

Switches

Safety Products

Explosion Proof

Terminal Blocks

Relays & Sockets

Circuit

Protectors

Power Supplies

LED Illumination

Controllers

Operator

Interfaces

Sensors

AUTO-ID

Emergency Stop Switches

SEMI

ø22 mm, 4-contact Emergency Stop Switch. Compact size—only 37.1 mm deep behind the panel

(screw terminal style 48.7 mm with terminal cover). Reliable “Safe break action.”

Standards and Specications

Contact Ratings

(NC main contacts/NO monitor contact)

Rated Insulation

Voltage (Ui)

Screw Terminal 250V

Solder Terminal

300V

PC Board Terminal

Connector

125V

Rated Thermal Current (Ith) 5A (connector style: 2.5A)

Rated Operating Voltage

(Ue)

30V 125V

250V

(Note 3)

Rated Operating Current

Main

Contacts

50/60 Hz

Resistive Load (AC-12) –

(Note 1)

Inductive Load (AC-15) –

(Note 2)

1.5A

Resistive Load (DC-12) 2A 0.4A 0.2A

Inductive Load (DC-13) 1A 0.22A 0.1A

Monitor

Contacts

50/60 Hz

Resistive Load (AC-12) – 1.2A 0.6A

Inductive Load (AC-14) – 0.6A 0.3A

Resistive Load (DC-12) 2A 0.4A 0.2A

Inductive Load (DC-13) 1A 0.22A 0.1A

• Minimum applicable load: 5V AC/DC, 1 mA (reference value)

(Operating area depends on the operating conditions and load types.)

• The rated operating currents are measured at resistive/inductive load types

specied in JIS C8201-5-1.

Note 1: Solder terminal/PC board terminal: 3A, Connector: 2.5A

Note 2: Solder terminal/PC board terminal: 1.5A

Note 3: Except for connector style.

Illumination Ratings

Rated Voltage Operating Voltage Rated Current

24V AC/DC 24V AC/DC ±10% 15 mA

Note: An LED lamp is built into the contact block and cannot be replaced.

Specifications

Applicable Standards

IEC60947-5-1, EN60947-5-1

IEC60947-5-5 (Note), EN60947-5-5

JIS C8201-5-1, UL508, UL991, NFPA79,

CSA C22.2 No. 14, GB14048.5

Operating Temperature

Non-illuminated: –25 to +60°C (no freezing)

LED illuminated: –25 to +55°C (no freezing)

Storage Temperature –45 to +80°C

Operating Humidity 45 to 85% RH (no condensation)

Operating Force

Push to lock: 32N

Pull to reset: 21N

Turn to reset: 0.27 N·m

Minimum Force Required

for Direct Opening Action

80N

Minimum Operator Stroke

Required for Direct

Opening Action

4.0 mm

Maximum Operator Stroke 4.5 mm

Contact Resistance

50 mΩ maximum (initial value)

Connector style: 30 mΩ (Note)

Insulation Resistance

100 MΩ minimum (500V DC megger)

Overvoltage Category II

Impulse Withstand Voltage 2.5 kV

Pollution Degree 3 (connector style: 2)

Operation Frequency 900 operations/hour

Shock Resistance

Operating extremes: 150 m/s

Damage limits: 1000 m/s

Vibration Resistance

Operating extremes: 10 to 500 Hz, amplitude 0.35 mm,

acceleration 50 m/s

Damage limits: 10 to 500 Hz, amplitude 0.35 mm,

acceleration 50 m/s

Mechanical Life 250,000 operations minimum

Electrical Life

100,000 operations minimum

250,000 operations minimum (24V AC/DC, 100 mA)

Degree of Protection

Panel front: IP65, IP67 (IEC 60529)

Terminal Protection: IP20 (screw terminal, when using XW9Z-VL2MF)

Short-circuit Protection

250V/10A fuse (Type aM, IEC60269-1/IEC60269-2)

Conditional

Short-circuit Current

1000A

Terminal Style

Solder terminal, PC board terminal,

M3 screw terminal, Connector

Recommended

Tightening Torque for

Locking Ring

2.0 N·m

Connectable Wire

Screw terminal: 0.75 to 1.25 mm

(AWG18 to 16)

Solder terminal / PC board terminal:

1.25 mm

maximum (AWG16 maximum)

Connector style: 0.3 to 0.85 mm

(AWG22 to 18)

Soldering Conditions 310 to 350°C, 3 seconds maximum

Recommended

Tightening Torque for

Terminal Screw

0.6 to 1.0 N·m

Weight ø40 mm: 72g ø60 mm: 81g

Note: When connecting the applicable connector to a 1m wire of 0.3 mm

(AWG22).

• The depth behind the panel is only 37.1 mm for 1 to 4 contacts

(screw terminal style 48.7 mm with terminal cover).

• The same depth behind the panel for illuminated and non-illuminated switches.

• IDEC’s original “Safe break action” ensures that the contacts open

when the contact block is detached from the operator.

• 1 to 4NC main contacts and 1 or 2NO monitor contact

• Push-to-lock, Pull or Turn-to-reset operator

• Direct opening action mechanism (IEC60947-5-5, 5.2, IEC60947-5-1, Annex K)

• Safety lock mechanism (IEC60947-5-5, 6.2)

• Degree of protection IP65, IP67 (IEC60529)

• Durable, silver with gold contacts.

• Screw terminal style is nger-safe (IP20).

• Two operator sizes: ø40 and ø60 mm

• Dark red (Munsell 5R4/12) or bright red (Munsell 7.5R4.5/14) colors

are available for the non-illuminated operator.

• Push-ON illumination available (operator size: ø60)

• Connector style available to reduce wiring time and wiring mistakes.

Direct Opening Action