Datasheet

Download catalogs and CAD from http://asia.idec.com/downloads
E-086
APEM
Switches &
Pilot Lights
Control Boxes
Emergency
Stop Switches
Enabling
Switches
Safety Products
Explosion Proof
Terminal Blocks
Relays & Sockets
Circuit
Protectors
Power Supplies
LED Illumination
Controllers
Operator
Interfaces
Sensors
AUTO-ID
Safety Products
Interlock
Switches
Non-contact
Interlock Switches
Safety Laser
Scanners
Safety Light
Curtains
Safety Modules
HS6B
HS6E
HS5D
HS5L
HS1L
Actuators for
HS1/HS5/HS6
Actuators/
Padlock Hasp
HS5 Series Sliding Actuator
Installation
When using with HS5D-
**
Z interlock switch When using with HS5L interlock switch
F
asten the actuator cover on at least two rectangular holes
and two round mounting holes using mounting screws
.
The thickness adjustment plate requires mounting holes.
HS5L
Interlock
Switch
Two Round Mounting Holes
Two Oblong Mounting Holes
4
36.286.5
10 to 11
20 to 22
5
34
5
0
-1
Thickness Adjustment Plate
(to be provided by the user)
Recommended thickness: 5 mm
0
-1
4
5
36.2
34
20 to 22
Fasten the actuator cover on at least two
oblong holes using mounting screws.
HS5D
Interlock Switch
Two Oblong
Mounting Holes
Operating Instructions
• When using the sliding actuator in a safety-related part of the system,
make sure of proper operation while observing the safety standards
and regulations of the relevant country or region where the actual
machine/system is used. Also, perform a risk assessment before
operation.
• Read the instruction sheet of the interlock switch carefully before
installation or operation.
• The actuator has projections on the end. Take care not to injure
hands.
• Regardless of door types, do not use the sliding actuator as a door
stop.
• When the actuator is inserted to an interlock switch in the different
direction from the open/close direction of the door, do not open
the door with excessive force, otherwise failure or damage will be
caused.
• When an operator enters the hazardous zone, take a safety measure
such as using padlock hasp HS9Z-PH5 so that the operator is not
trapped inside and the machine is not operated while the operator is
in the hazardous zone.
• Do not install the sliding actuator as shown below, otherwise the
actuator may be removed from the interlock switch due to shocks.
• Ensure to slide the sliding actuator completely. Incomplete insertion
of the actuator may cause unstable contact operation of the interlock
switch. Also, door may not be opened, damaging the actuator.
• Do not close the door when the actuator is slid out of the cover,
otherwise the actuator may damaged.
• When using the sliding actuator, take care so that ngers or hands
are not caught between the actuator and interlock switch.
• When installing the sliding actuator over
the interlock switch as shown below, do not
apply a shock exceeding 100 m/s
2
to the
actuator, otherwise the actuator may be
inserted to the interlock switch and cause
unintended machine operation.
• Use the sliding actuator with HS5D/HS5E/
HS5E-K/HS5Linterlock switches only. Do not
use with other products.
• Do not modify or disassemble the sliding
actuator.
Adjustment
1. Mounting Reference Position
• The mounting reference position of sliding actuator is shown below.
HS5D Interlock Switch
Mounting
P
osition
T
olerance: ±2.5
26.7
21
4
Mounring
Reference
(Mounting position tolerance 4
)
+3
-1
2. Recommended Tightening Torque of Mounting Screws
• M5 screws for mounting the sliding actuator: 4.5 to 5.5 N·m
• M4 screws for mounting the interlock switch: 1.8 to 2.2 N·m
Note: The above recommended tightening torque of the mounting screws are
the values with hex socket head bolts. When other screws are used and
tightened to a smaller torque, make sure that the screws do not become
loose after mounting.
Interlock
Switch
HS9Z-SH5
Instructions
Download catalogs and CAD from http://eu.idec.com/downloads