Datasheet

LF1D/LF2D LED Illumination Units (Wide Angle & High Illuminance Model)
TM
Safety Precautions
Instructions
IDEC CORPORATION (USA)
1175 Elko Drive
Sunnyvale, CA 94089-2209, USA
Tel: [phone] / (800) 262-IDEC (4332)
Fax: [phone]
E-mail: [e-mail]
IDEC CANADA LIMITED
3155 Pepper Mill Court, Unit 4
Mississauga, Ontario, L5L 4X7, Canada
Tel: [phone]
Toll Free:
(800) 262-IDEC (4332)
Fax: [phone]
E-mail: [e-mail]
IDEC AUSTRALIA PTY. LTD.
Unit 17, 104 Ferntree Gully Road,
Oakleigh, Victoria 3166, Australia
Tel: [phone], Toll Free: 1800-68-4332
Fax: [phone]
E-mail: [e-mail]
7-31, Nishi-Miyahara 1-Chome, Yodogawa-ku, Osaka 532-8550, Japan
Tel: [phone], Fax: [phone]
E-mail: [e-mail]
Specifications and other descriptions in this catalog are subject to change without notice.
Cat. No. EP1419-0 MAY 2012 PDF
IDEC ELECTRONICS LIMITED
Unit 2, Beechwood, Chineham Business Park,
Basingstoke, Hampshire RG24 8WA, UK
Tel: [phone], Fax: [phone]
E-mail: [e-mail]
IDEC ELEKTROTECHNIK GmbH
Wendenstrasse 331, 20537 Hamburg, Germany
Tel: [phone] - 0, Fax: [phone] - 24
E-mail: [e-mail]
IDEC (SHANGHAI) CORPORATION
Room 701-702 Chong Hing Finance Center,
No. 288 Nanjing Road West, Shanghai 200003, PRC
Tel: [phone]
Fax: [phone]
E-mail: [e-mail]
IDEC (BEIJING) CORPORATION
Room 211B, To wer B, The Grand Pacific Building,
8A Guanghua Road, Chaoyang District,
Beijing 100026, PRC
Tel: [phone], Fax: [phone]
IDEC (SHENZHEN) CORPORATION
Unit AB-3B2, Tian Xiang Building, Tian’an Cyber Park,
Fu Tian District, Shenzhen, Guang Dong 518040, PRC
Tel: [phone], Fax: [phone]
IDEC IZUMI (H.K.) CO., LTD.
Units 11-15, Level 27, Tower 1,
Millennium City 1, 388 Kwun Tong Road,
Kwun Tong, Kowloon, Hong Kong
Tel: [phone], Fax: [phone]
E-mail: [e-mail]
IDEC TAIWAN CORPORATION
8F-1, No. 79, Hsin Tai Wu Road, Sec. 1,
Hsi-Chih District, New Taipei City, Taiwan
Tel: [phone], Fax: [phone]
E-mail: [e-mail]
IDEC IZUMI ASIA PTE. LTD.
No. 31, Tannery Lane #05-01,
HB Centre 2, Singapore 347788
Tel: [phone], Fax: [phone]
E-mail: [e-mail]
www.idec.com
Do not disassemble, repair, or modify LF1D/LF2D. Otherwise •
electric shock, fire, or malfunction may occur.
Turn off power before wiring. To prevent electric shock or dam- •
age, ensure that the wiring is correct.
Do not stare directly into the LF1D/LF2D while it is lit, and do not •
project the light towards other people, otherwise their eyes may
be injured.
The LF1D/LF2D is general-purpose industrial electric device. •
Do not use with electronic equipment which may cause harm or
injury to anyone or threaten life in case a malfunction or failure
occurs.
Before designing equipment and powering up units, confirm the •
specifications described in the instruction sheet.
Apply voltage within the rated value, otherwise the LED elements •
may be damaged.
The LF1D/LF2D is vulnerable to static electricity. Take sufficient •
measures for protection against static electricity and voltage
surges.
Make sure that the unit is not dropped during transportation, •
installation, and operation, otherwise damage may result.
Do not pull or push the cable, otherwise damage may result. •
Allow sufficient slack to the cable while wiring.
Do not apply excessive force. Do not leave a damaged unit •
unattended or use a damaged unit. Reinforced glass illumination
surface requires extra attention.
Ensure correct operating temperature. Otherwise rise in internal •
temperature may result in damage to the unit.
Do not use or store in a location subjected to vibration and shock. •
Do not use in the following locations: •
∗Exposure to direct sunlight, near heaters, high temperatures
∗ Subject to chemicals, and corrosive gases
(Plastic illumination surface: avoid iron powder and oil)
∗Places with high humidity such as basements and
greenhouses
∗ Cold storage warehouses (make sure that no freezing occurs)
Do not loosen screws, otherwise the protection characteristics will •
be impaired.
For the LF2D, make sure to provide sufficient strength for mount- •
ing panel. Required waterproof characteristics cannot be ob-
tained if a distorted mounting panel is used.
(12/05/18)