Baby Bath™ Thermometer + Wireless Baby Monitor OQ005 Instructions Read and save these instructions. OQ005 IM_v1 1105-PB 0216.
Table of Contents Baby Bath™ Thermometer...........................................................5 This is Not a Toy.........................................................................5 Warnings....................................................................................5 Precautions.................................................................................6 General Instructions....................................................................7 Front of the Product.....................
Table of Contents Back View – “Parent” Unit....................................................18 LCD – “Parent” Unit.............................................................19 Front View – “Baby” Unit......................................................20 Back View – “Baby” Unit......................................................21 Power Requirements.............................................................22 Neck Lanyard – “Parent Unit.................................................
Table of Contents Setting the Alarm..................................................................29 Feeding Timer.......................................................................30 Backlight...............................................................................31 Reset.....................................................................................32 Specifications........................................................................32 Statement of FCC Compliance.....................
Baby Bath Thermometer This is Not a Toy Product is tested and is in compliance with toy safety standard EN71. IT IS NOT meant to be used as A TOY and is not suitable for children under 3 years. Please retain this instruction manual for future reference. Warnings • This product should only be operated by an adult and should not be used as a toy for children.
Precautions This unit is engineered to provide you with years of satisfactory service, if you handle it carefully. The following are precautions that should be observed: • Do not clean the unit with abrasive or corrosive materials. This may scratch the plastic parts and corrode the electronic circuit. • Clean the product thoroughly after each bath. Rinse with warm water and dry with a soft, dry cloth. Never store the product when it is wet.
Precautions • Due to continuing improvements, actual product may differ slightly from the product described herein. • The technical specifications for this product and the contents of the instruction manual are subject to change without notice. General Instructions Front of the Product 1 2 3 4 5 1. MEMORY appears on the LCD when you are setting or displaying a user-defined temperature. 2. button turns the unit on or off. It also disables the alarm sound. OQ005 IM_v1 1105-PB 0216.
Front of the Product 3. The LCD also shows the temperature in °C or °F. 4. MEMORY button sets the user-defined temperature range. It also disables the alarm sound. 5. Low-battery indicator Back of the Product 1 3 2 4 1. The RESET button returns all the settings to default values. 2. Thermo sensor takes water-temperature readings. 3. °C/°F button selects the temperature unit. 4. Battery compartment holds 2 AAA batteries (included). OQ005 IM_v1 1105-PB 0216.
Batteries 1. Remove the screws. (When you first remove the product from its packaging, the screws will already be loose.) 2. Once loose, pull the two sections apart, or to remove the base, insert a blunt instrument into the groove. 3. Insert 2 AAA batteries (included), ensuring proper +/– polarities are observed. 4. To close, line up the dot with the groove. The screw holes are now lined up. 5. Tighten the screws. Ensure the unit is firmly closed to keep it watertight.
Basic Functions Temperature Ranges To obtain a temperature reading, place the unit in the water. The unit has three preset temperature ranges to indicate when the bath water is cold, comfortable or hot. Comfort Level Color Temperature Range °F Temperature Range °C Cold Red 32.0°F - 89.9°F 0.0°C - 31.9°C Comfortable Green 90.0°F - 100.0°F 32.0°C - 37.0°C Hot 100.1°F - 122.0°F 37.1°C - 49.
Basic Functions Temperature Unit To change the display measurement unit, slide the °C/°F switch to the desired setting. User-defined Temperature Range The default comfort temperature range for the baby’s bath water is 90°F to 100°F (32°C to 37°C). To set a new water-temperature range to the desired level: 1. Mix the water thoroughly to help ensure the temperature is even. 2. Press and hold MEMORY for two seconds. 3.
Basic Functions Notes: • To display the user-defined water temperature, press MEMORY. • The unit defines the temperature + or – 3.6°F (+ or – 2°C) of the temperature stored. For example, if the temperature recorded is 80.6°F (27°C), any reading below 77°F (25°C) appears on the LCD as Cold and any reading above 84.2°F (29°C) appears on the LCD as Hot. • The user-defined temperature range can only be set if the water temperature is between 32°F and 98.6°F (0°C and 37°C).
Technical Specifications Type Description Display Temperature Range 32°F to 122°F (0°C to 50°C) Temperature Resolution +/– 0.1°C (0.2°F) Measurement Unit User-selectable °F/°C Unit Dimensions (H x W x D) Approximately 3" x 3" x 1" Unit Weight 3.88 ounces Batteries 2 AAA (UM-4) 1.5V 13 OQ005 IM_v1 1105-PB 0216.
Baby Monitor with Indoor Temperature Precautions This unit is engineered to give you years of satisfactory service, if you handle it carefully. Here are a few precautions: • Do not immerse the unit in water. • Do not cover the ventilation holes. Ensure items that are nearby, such as newspapers, tablecloths, curtains, blankets, beddings, etc., cannot accidentally cover the ventilation holes. • Use a soft, slightly moistened cloth to clean the unit.
Precautions • Remove the batteries before storing the product for a long time. Do not mix new and old batteries. Note: The technical specifications for this product and the contents of the instruction manual are subject to change without notice. CAUTION: To reduce the risk of electric shock, do not expose this appliance to rain or moisture. CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type. Batteries are supplied by Rickbery, NiMH, 3.
Warnings • This product should only be operated by an adult and should not to be used as a toy for children. • This product is not intended and should not be used as a replacement for responsible adult supervision; it only acts as a support for your child-caring purpose. Any type of liability beyond statutory warranty regulations or resulting from improper use of this product and/or use not in accordance with product warnings, precautions and instructions is excluded.
General Instructions Front View – “Parent” Unit 1 3 4 5 6 2 1. : Turns the unit on and off; activates backlight. 2. Sound Light Indicators: Shows the sound level received from the “baby” unit. 3. +/– : Increases and decreases volume; changes setting value; activates and disables alarm. 4. MODE: Displays or sets the clock / alarm / voice-activation sensitivity level. 5. : Sets and operates the feeding timer. 6. Speaker 17 OQ005 IM_v1 1105-PB 0216.
Back View – “Parent” Unit 1 4 2 5 3 1. AC Adapter Jack 2. Table Stand 3. RESET Button 4. Lanyard Holes 5. °C/°F Selection 18 OQ005 IM_v1 1105-PB 0216.
LCD – “Parent” Unit 1 7 2 3 4 5 8 6 9 1. Connection / Signal Icon 2. Low Battery on the “Baby” Unit 3. Battery Status on the “Parent” Unit 4. Voice Activation Sensitivity Level 5. Alarm Icon 6. Feeding Timer Icon 7. Indoor Temperature 8. Clock / Alarm / Timer 9. Volume Level OQ005 IM_v1 1105-PB 0216.
Front View – “Baby” Unit 2 3 4 5 1 1. Microphone 2. / : Turns the unit on and off; searches for channel. 3. : Turn the night-light on and off. 4. Night-light 5. LED Indicator: Flashes during data transmission. 20 OQ005 IM_v1 1105-PB 0216.
Back View – “Baby” Unit 1 2 3 4 1. AC Adapter Jack 2. Table Stand 3. Battery Compartment 4. RESET Button 21 OQ005 IM_v1 1105-PB 0216.
Power Requirements “Baby” Unit The adapter should be used at all times. Insert one end of the adapter into the unit, then plug the other end into a wall outlet. The 3 AAA (UM-4 1.5V) batteries (purchase separately) are for backup use only. Before first use, insert the batteries, ensuring proper +/– polarities are observed. 22 OQ005 IM_v1 1105-PB 0216.
Power Requirements “Parent” Unit This unit uses a rechargeable battery pack (3 AAA/UM-4 NiMH). Insert the rechargeable battery pack by connecting the end of the wire into the indentation located at the bottom right of the battery compartment. To recharge the battery, connect the adapter into the unit, then plug the other end into a wall outlet. 23 OQ005 IM_v1 1105-PB 0216.
Power Requirements An animated battery icon indicates that it is charging. steadily appears when the battery is fully charged. Before first use, charge the batteries for 12 hours and press RESET. After the first charge, you only need to charge the unit until the battery icon indicates that it is fully charged. Low Battery Flashes when the “Baby” unit is low. A series of warning beeps is emitted every minute until the battery is fully exhausted. Flashes when the “Parent” unit is low.
Power On/Off To turn either unit on or off, press and hold . Setup 1. Insert batteries and plug in adapters. 2. Turn the “Baby” unit on, then turn on the “Parent” unit. 3. Place the two units close to each other for five seconds. This allows the units to “recognize” each other. 4. Position the units no more than 980 feet (300 meters) from each other. For best results: • Keep the units away from electrical or mechanical objects, direct sunlight or moisture.
Selecting Channels – “Baby” Unit If there is interference or transmission trouble between the two units, press the button on the “Baby” unit. Night-Light – “Baby” Unit To turn the night-light on and off, press the button. Volume To change the volume (0-5), press the +/– button on the “Parent” unit. Notes: • All the alarm sounds are independent of the volume level. • You may hear a high-pitched noise if the “Parent” unit is placed too close to the “Baby” unit.
Sound Light Indicators The sound light indicators on the “Parent” unit can alert you visually to a baby’s sound. The louder the sound received from the “Baby” unit, the more the lights are on. Connection Signal Status The connection icon shows you the status of the signal between the two units. Lost Link Normal Signal The icons are animated when the two units are linked.
Temperature Display The “Baby” unit measures the surrounding temperature. If “---” is shown, the “Baby” unit cannot transmit the temperature reading. Slide the °C/°F switch, located in the battery compartment of the “Parent” unit, to the desired setting. Clock/Alarm To toggle between the clock and the alarm display, press the MODE button. Set Clock/Voice-Activation Sensitivity Level 1. To enter Setting mode, press and hold MODE button. 2. To change the setting, press + or – button.
Set Clock/Voice-Activation Sensitivity Level Level Sensitivity 0 Maximum 3 High 2 Medium 1 Low Note: The voice-activation sensitivity feature increases/decreases the level of sound the “Parent” unit emits. When set to 0, all sounds, regardless of level, can be heard on the “Parent” unit. Setting the Alarm 1. To view alarm display, press MODE. 2. To select alarm on, press + or –. 3. To enter the Setting mode, press and hold MODE. 29 OQ005 IM_v1 1105-PB 0216.
Setting the Alarm 4. To change the setting, press + or –. To quickly scroll through the numbers, press and hold + or –. 5. To confirm a setting and move on to the next one, press MODE. The setting sequence is hours, then minutes. To Activate or Deactivate the Alarm When in Alarm display, press + or –. If the alarm is off, “—” appears. To Stop the Alarm Sound Press any button except . Feeding Timer The feeding timer is useful to help you develop a feeding routine for your baby. To Set the Timer . 1.
Feeding Timer 3. To increase or decrease the time in 30-minute intervals, press + or –. To quickly scroll through the numbers, press and hold + or –. 4. To confirm, press . Timer Functions • To start/stop/retrieve the last setting, press the • To reset the timer, press and hold . or press RESET. • To view the clock while the timer is running, press MODE. flashes when the timer is in use. • To turn off the 2-minute alarm that sounds when the timer has reached 0, press any button except .
Reset To return either unit to the default settings, insert a blunt stylus into the RESET hole, located in the battery compartment of each unit. Specifications Type Description Clock Time 12- or 24-hour format Alarm 2 minutes Feeding Timer 30 minutes to 24 hours RF Frequency 2.4GHz Transmission Range 980 feet (300 meters) open area Temperature Measuring Range 14°F to 122°F (–10°C to 50°C) Operating Range 32°F to 122°F (0°C to 50°C) Temperature Unit °C/°F 32 OQ005 IM_v1 1105-PB 0216.
Specifications Power Description “Baby” Unit 6V DC 200mA AC adapter/ 3 x 1.5V UM-4/AAA batteries “Parent” Unit 6V DC 200mA AC adapter/ 3.6V NiMH rechargeable battery pack Measurements Description Dimensions – Both Units (H x W x D) Approximately 4" x 21/2" x 2" (96 x 63 x 40 mm) Weight – “Parent” Unit 2.4 ounces (68 grams) without battery Weight – “Baby” Unit 2.2 ounces (62 grams) without battery 33 OQ005 IM_v1 1105-PB 0216.
Statement FCC Compliance of FCC Compliance Statement WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Warranty What Is Covered This warranty covers any defects in materials or workmanship, with the exceptions stated below. How Long Coverage Lasts This warranty runs for 90 days from the date of original purchase. What Is Not Covered This warranty does not cover damage caused by misuse or use other than as intended and described in the product instruction manual, or loss or damage to batteries or removable parts.