EN Wireless Outdoor Temperature and Humidity Sensor (Model #: PS-R01) User Manual PS R01A English Cover r7 1 10/17/03, 6:29 PM
EN TABLE OF CONTENTS About Oregon Scientific ............................................ 1 About this guide ....................................................... 2 Product overview ....................................................... 3 Getting started .......................................................... 4 Set up ................................................................. 4 Change channel .................................................. 5 Comfort zone ....................................
EN In this box, you will find: ABOUT THIS GUIDE Congratulations on your selection of the Philippe Starck with Oregon Scientific Wireless Outdoor Temperature and Humidity Sensor (PS-R01). • • Remote unit Batteries This sensor is compatible with a wide variety of weather monitoring tools, and can be used with any STARCK / Oregon Scientific Weather Stations. Keep this manual handy as you use your new product.
EN PRODUCT OVERVIEW DESCRIPTIONS 1 1. 2. 3. 4. 5. 6. 7. 8. 9.
EN SET UP 1. Place remote unit as close as possible to the main unit. 2. Remove the battery compartment lid. (You will need a small Phillips screwdriver.) 3. Assign a Channel Number. If you are using more than one remote unit, select a different channel number for each unit. 4. Set the measurement unit. 5. Insert the batteries. Match the polarity, as shown in the battery compartment. 6. Press RESET with the point of a blunt object (such as a ball point pen).
EN 7. 8. You may need to experiment with various locations to get the best reception. Replace the battery compartment lid. Secure. Mount the remote unit on a flat surface using the recess hole on the back of the unit. For best results: • Place the unit out of direct sunlight and moisture. • Do not place the remote unit more than 60 - 90 feet (20 - 30 meters) from the main (indoor) unit. • Position the unit so that it faces the main (indoor) unit. Minimize obstructions such as doors, walls, and furniture.
EN TRENDS The trend arrow for the last 30 minutes always displays. Outdoor temperature and humidity trends are shown separately. COMFORT ZONE The outdoor comfort zones are shown under the following conditions. Zone Temperature Relative Humidity Any >70% Trend Wet Any <40% 68 - 77 °F (20 - 25 °C) 40 - 70% Temperature Relative Humidity +0.9 °F > +3% Steady Steady -0.
EN LOW BATTERY WARNING Replace the batteries whenever the low battery signal ( ) shows on the remote unit, or on the remote unit area of the main unit. radio frequency link with main unit). Refer to the User Manual for the main unit for more information. SAFETY AND CARE Wash the unit with a slightly damp cloth and mild detergent. Avoid dropping the unit or placing it in direct sunlight or in damp or high-traffic locations. NOTE Do not use rechargeable batteries.
EN • • • • • • • • Do not subject the main unit to extreme force, shock, or fluctuations in temperature or humidity. Do not tamper with the internal components. Do not mix new and old batteries or batteries of different types. Do not use rechargeable batteries with this product. Remove the batteries if storing this product for a long period of time. Do not scratch the LCD display. Do not make any changes or modifications to this product. Unauthorized changes may void your right to use the product.
EN SPECIFICATIONS Dimensions LxWxH 3 x 1.4 x 3.1 in (75 x 35 x 78.3 mm) Weight 0.3 lbs / 136 grams with battery Frequency RF frequency Range Temperature Unit Range Resolution Channel No. Unit Power Transmission °F or °C -4 °F to 140 °F (20 °C to 60 °C) 0.2 °F (0.1 °C) 433 MHz 30 meters (98 feet) with no obstructions approximately every 40 seconds 1, 2, or 3 °F or °C 2 x UM-4 (AAA) 1.
EN • • FCC NOTICE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
EN DECLARATION OF CONFORMITY The following declaration is required for us to fully meet FCC requirements. The information below is not to be used as contact for support or sales. Please call our customer service number (listed on our website at www.oregonscientific.com, or on the warranty card for this product) for all inquiries instead. We declare that the product is in conformity with Part 15 of the FCC Rules. Name: Address: Oregon Scientific, Inc.
EN Operation is subject to the following two conditions: 1) This device may not cause harmful interference. 2) This device must accept any interference received, including interference that may cause undesired operation. CAUTION — The content of this manual is subject to change without further notice. — Due to printing limitation, the displays shown in this manual may differ from the actual display. — The contents of this manual may not be reproduced without the permission of the manufacturer.
