Owner manual

ManualsBrandsIEI Integration ManualsMonitorsDM_Series v1.14

DM Series Industrial Monitor

Page 1

IEI Technology Corp.

User Manual

P4DM Series Industrial Monitor

MODEL:

DM Series

Industrial Touch Screen Monitor

IP 65 Protection, VGA/DVI-D, 9-36V Input

Rev. 1.14 – 15 July, 2009

Summary of content (198 pages)

PAGE 1
DM Series Industrial Monitor P4DM Series Industrial Monitor IEI Technology Corp. MODEL: DM Series Industrial Touch Screen Monitor IP 65 Protection, VGA/DVI-D, 9-36V Input User Manual Page 1 Rev. 1.
PAGE 2
DM Series Industrial Monitor Revision Date Version Changes 15 July, 2009 1.14 Updated “Chapter 6: OSD Controls” April, 2008 1.13 Added DM-121GX models information Added DM-190 rack mount installation Added the smartOSD appendix July, 2007 1.12 Cautions for VESA mounting kit are added in p46, p140 May, 2007 1.11 AV-5300 AD Board CN25 connector pin 3 voltage changed to +9V~+36V input April, 2007 1.10 Updated Figure 1-3 and Section 4.4 for AV-5300 AD Board V2.0 March, 2007 1.
PAGE 3
DM Series Industrial Monitor Copyright COPYRIGHT NOTICE The information in this document is subject to change without prior notice in order to improve reliability, design and function and does not represent a commitment on the part of the manufacturer. In no event will the manufacturer be liable for direct, indirect, special, incidental, or consequential damages arising out of the use or inability to use the product or documentation, even if advised of the possibility of such damages.
PAGE 4
DM Series Industrial Monitor Manual Conventions WARNING! Warnings appear where overlooked details may cause damage to the equipment or result in personal injury. Warnings should be taken seriously. Warnings are easy to recognize. The word “warning” is written as “WARNING,” both capitalized and bold and is followed by text. The text is the warning message. A warning message is shown below: WARNING: This is an example of a warning message.
PAGE 5
DM Series Industrial Monitor CAUTION: This is an example of a caution message. Failure to adhere to cautions messages may result in permanent damage to the DM Series. Please take caution messages seriously. NOTE: These messages inform the reader of essential but non-critical information. These messages should be read carefully as any directions or instructions contained therein can help avoid making mistakes. Notes are easy to recognize.
PAGE 6
DM Series Industrial Monitor Packing List NOTE: If any of the components listed in the checklist below are missing, please do not proceed with the installation. Contact the IEI reseller or vendor you purchased the DM Series from or contact an IEI sales representative directly. To contact an IEI sales representative, please send an email to sales@iei.com.tw. The items listed below should all be included in the DM Series package. 1 x DM-190/170/150/121/104/84 series industrial monitor.
PAGE 7
DM Series Industrial Monitor Table of Contents 1 INTRODUCTION................................................................................................... 21 1.1 DM SERIES INDUSTRIAL MONITOR OVERVIEW ........................................................ 22 1.1.1 Standard Features ............................................................................................ 22 1.1.2 Model Variations .............................................................................................. 22 1.
PAGE 8
DM Series Industrial Monitor 2.4 PHYSICAL DIMENSIONS ............................................................................................ 39 2.4.1 General Physical Dimensions.......................................................................... 39 2.4.2 DM-190 Physical Dimensions ......................................................................... 40 2.4.3 DM-170 Physical Dimensions ......................................................................... 41 2.4.
PAGE 9
DM Series Industrial Monitor 3.2.1 Touch Panel Models......................................................................................... 65 3.2.2 Touch Panel Dimensions.................................................................................. 66 3.2.3 Touch Panel Specifications .............................................................................. 67 3.2.4 Touch Panel RS-232 Controller Specifications................................................ 69 3.2.
PAGE 10
DM Series Industrial Monitor 4.3.5 AV-5350 Rear Panel Connectors ..................................................................... 94 4.3.6 AV-5350 Onboard Jumper................................................................................ 94 4.3.7 AV-5350 Internal Peripheral Connectors ........................................................ 95 4.3.8 5V Power Connector........................................................................................ 95 4.3.9 12V Power Connector................
PAGE 11
DM Series Industrial Monitor 4.4.21 DVI-D Connector......................................................................................... 123 5 INSTALLATION .................................................................................................. 124 5.1 INSTALLATION PRECAUTIONS ................................................................................. 125 5.2 UNPACKING ............................................................................................................ 126 5.2.
PAGE 12
DM Series Industrial Monitor 6.1.2 OSD Menu Structure ...................................................................................... 154 6.2 USING THE OSD..................................................................................................... 156 6.2.1 Main Display Features................................................................................... 156 6.2.2 Gamma........................................................................................................... 157 6.2.
PAGE 13
DM Series Industrial Monitor C.4.3 Image Page.................................................................................................... 190 C.4.4 Display Page (for analog signal) .................................................................. 191 C.4.5 Color Page .................................................................................................... 192 C.4.6 PIP Page........................................................................................................ 193 C.4.
PAGE 14
DM Series Industrial Monitor List of Figures Figure 1-1: Typical Monitor Front View.....................................................................25 Figure 1-2: Typical Bottom Panel View .....................................................................26 Figure 1-3: AV-5300 AD Board ...................................................................................27 Figure 2-1: Front Panel Variant 1...............................................................................
PAGE 15
DM Series Industrial Monitor Figure 4-10: RS232 Serial Connector Pinout Locations..........................................87 Figure 4-11: VGA Connector Pinout Locations........................................................89 Figure 4-12: Jumpers ..................................................................................................89 Figure 4-13: Jumper Location....................................................................................90 Figure 4-14: AV-5350 AD Board Overview ........
PAGE 16
DM Series Industrial Monitor Figure 5-2: VGA Connector ..................................................................................... 131 Figure 5-3: DVI-D Connector ................................................................................... 131 Figure 5-4: 12V Power Connector........................................................................... 132 Figure 5-5: DC Power Connector............................................................................
PAGE 17
DM Series Industrial Monitor Figure 6-8: Signal Menu........................................................................................... 161 Figure 7-1: Driver CD Pop Up Screen..................................................................... 165 Figure 7-2: Install Shield Wizard Preparation........................................................ 166 Figure 7-3: Welcome Screen ...................................................................................
PAGE 18
DM Series Industrial Monitor List of Tables Table 1-1: DM Series Base Model Variants...............................................................23 Table 1-2: DM Series Specifications..........................................................................29 Table 2-1: Front Panel Variants .................................................................................32 Table 2-2: General Physical Dimensions ..................................................................
PAGE 19
DM Series Industrial Monitor Table 4-3: AV-9350 Onboard Jumper ........................................................................76 Table 4-4: 5V Power Connector Pinouts ...................................................................77 Table 4-5: Debugged Port Connector Pinouts .........................................................78 Table 4-6: External OSD and LED Indication Connector Pinouts ..........................79 Table 4-7: Serial Communications Connector Pinouts ......................
PAGE 20
DM Series Industrial Monitor Table 4-35: External OSD and LED Indication Connector Pinouts ..................... 112 Table 4-36: Backlight Inverter Connector Pinouts................................................ 113 Table 4-37: LVDS Output Connector Pinouts........................................................ 115 Table 4-38: Power Output Connector Pinouts (CN12).......................................... 116 Table 4-39: Power Output Connector Pinouts (CN13)..........................................
PAGE 21
DM Series Industrial Monitor Chapter 1 1 Introduction Page 21
PAGE 22
DM Series Industrial Monitor 1.1 DM Series Industrial Monitor Overview The DM series industrial monitor is the latest member of IEI’s line of sophisticated LCD designs, and it has been improved to be RoHS compliant. It is designed to fit industrial automation, or any other applications that require minimum installation space and flexible configuration. The flat front panel provides IP 65 protection, which effectively wards off dust and water.
PAGE 23
DM Series Industrial Monitor three digit size of the monitor. Special features with the associated model prefix are listed in Table 1-1.
PAGE 24
DM Series Industrial Monitor o Automation & Control o o o Interactive education use Plant environment monitoring Factory automation HMI terminal Shop-floor/MES control Self-service Kiosk o o o o o Full-service receptionist kiosk Hospital self-registrating terminal Interactive photo kiosk Video rental kiosk Self-service POS terminal 1.2.
PAGE 25
DM Series Industrial Monitor 1.3.1 Front View The front of the DM series industrial monitor is a flat panel TFT LCD screen surrounded by an aluminum frame. A control button panel (OSD), if available, is located either vertically on the right side of the frame or horizontally along the bottom of the frame with the following control buttons: LCD On/Off Auto Left Right Menu The OSD panel also has one power LED. Figure 1-1 shows a typical monitor front view.
PAGE 26
DM Series Industrial Monitor 1.3.2 Bottom Panel View Figure 1-2 shows the bottom panel of the DM-190 monitor. Other models may include or exclude additional connectors. Refer to Section 2.3 for listings of monitors and their connectors. All connectors are fully described in Section 5.4.
PAGE 27
DM Series Industrial Monitor 1.3.3 AD Board The DM series industrial monitor AD board provides a wide variety of control interfaces, receiving and managing signals from a CPU card through cabling. Figure 1-3 shows the AV-5300 AD board as a sample of a typical AD board for the DM series industrial monitor. Refer to Chapter 4 for a complete description of AD boards and their connectors.
PAGE 28
DM Series Industrial Monitor 1.4 Series Specifications Table 1-2 shows the DM Series specifications. Model LCD Size DM-65 DM-84 DM-104 DM-121 DM-150 DM-170 DM-190 6.5” 8.4” 10.4” 12.1” 12” 17” 19” VGA VGA VGA VGA VGA VGA VGA DVI-D DVI-D DVI-D DVI-D Input Interface Max. 800x600/ 640x480 800x600 800x600 Resolution 1024x768 1280x1024 1280x1024 1024x768 Brightness 400/500 400 400 550:1 400:1 500:1 400/450 350 300 300 400:1 500:1 700:1 262K 16.2M 16.2M 0.297 0.
PAGE 29
DM Series Industrial Monitor Model DM-65 DM-84 DM-104 DM-121 DM-150 DM-170 DM-190 Color Silver Silver Silver Silver Silver Silver Silver 0~50°C 0~50°C 0~50°C 0~50°C 0~50°C 0~50°C 0~50°C IP 65 IP 65 IP 65 IP 65 IP 65 IP 65 IP 65 1kg 1.8kg 3kg 3.8kg 6kg 8.6kg 10kg Operation Temperature IP Level N/G Weight Table 1-2: DM Series Specifications 1.
PAGE 30
DM Series Industrial Monitor THIS PAGE IS INTENTIONALLY LEFT BLANK Page 30
PAGE 31
DM Series Industrial Monitor Chapter 2 2 Mechanical Overview Page 31
PAGE 32
DM Series Industrial Monitor 2.1 Introduction This chapter describes the general mechanical overview of the DM series monitors including front and bottom panel variations, available interfaces and overall dimensions. 2.2 Front Panel The front panel of the DM series industrial monitor is comprised of a TFT LCD in an aluminum frame with an OSD control panel. 2.2.1 Front Panel Variants Table 2-1 shows the three front panel variants for the DM series industrial monitor.
PAGE 33
DM Series Industrial Monitor 2.2.2 Front Panel Variant 1 The following models of the DM series industrial monitor have an OSD control panel located vertically along the right side of the aluminum frame: DM-170 DM-150 DM-121 DM-104 DM-84 Figure 2-1 shows the location of the front panel variant 1 OSD controls.
PAGE 34
DM Series Industrial Monitor 2.2.3 Front Panel Variant 2 The following model of the DM series industrial monitor has an OSD control panel located horizontally along the bottom of the aluminum frame: DM-190 Figure 2-2 shows the location of the front panel variant 2 OSD controls.
PAGE 35
DM Series Industrial Monitor 2.2.4 Front Panel Variant 3 The following model of the DM series industrial monitor has an OSD control panel located in-line along the bottom of the aluminum frame: DM-65 Figure 2-3 shows the location of the front panel variant 3 OSD controls. Figure 2-3: Front Panel Variant 3 2.3 Bottom Panel All peripheral device connectors are located on the bottom panel of the DM series industrial monitor.
PAGE 36
DM Series Industrial Monitor Page 36 USB connector
PAGE 37
DM Series Industrial Monitor 2.3.2 DM-65 Connectors The following is a list of the bottom panel peripheral device connectors used on the DM-65 series industrial monitor. VGA connector 12V power connector RS-232 serial connector (T-R models only) 2.3.3 DM-84 Connectors The following is a list of the bottom panel peripheral device connectors used on the DM-84 series industrial monitor.
PAGE 38
DM Series Industrial Monitor 2.3.5 DM-121 Connectors The following is a list of the bottom panel peripheral device connectors used on the DM-121 series industrial monitor. VGA connector DVI-D connector 12V power connector 9~36V terminal block (M models only) RS-232 serial connector (T-R models only) USB connector (USB/T-R models only) 2.3.6 DM-150 Connectors The following is a list of the bottom panel peripheral device connectors used on the DM-150 series industrial monitor.
PAGE 39
DM Series Industrial Monitor 2.3.8 DM-190 Connectors The following is a list of the bottom panel peripheral device connectors used on the DM-190 series industrial monitor. VGA connector DVI-D connector 12V power connector 9~36V terminal block (M models only) RS-232 serial connector (T-R models only) 2.4 Physical Dimensions The following sections describe the physical dimensions for each model of the DM series industrial monitor. 2.4.
PAGE 40
DM Series Industrial Monitor 2.4.2 DM-190 Physical Dimensions The physical dimensions of the DM-190 are shown in Figure 2-4.
PAGE 41
DM Series Industrial Monitor 2.4.3 DM-170 Physical Dimensions The physical dimensions of the DM-170 are shown in Figure 2-5.
PAGE 42
DM Series Industrial Monitor 2.4.4 DM-150 Physical Dimensions The physical dimensions of the DM-150 are shown in Figure 2-6.
PAGE 43
DM Series Industrial Monitor 2.4.5 DM-121 Physical Dimensions The physical dimensions of the DM-121 are shown in Figure 2-7.
PAGE 44
DM Series Industrial Monitor 2.4.6 DM-104 Physical Dimensions The physical dimensions of the DM-104 are shown in Figure 2-8.
PAGE 45
DM Series Industrial Monitor 2.4.7 DM-84 Physical Dimensions The physical dimensions of the DM-84 are shown in Figure 2-9.
PAGE 46
DM Series Industrial Monitor 2.4.8 DM-65 Physical Dimensions The physical dimensions of the DM-65 are shown in Figure 2-10.
PAGE 47
DM Series Industrial Monitor 2.5 Optional Mounting Kits The following sections describe the various optional mounting kits available for each model of the DM series industrial monitor. Refer to Section 5.5 for detailed instructions on the different mounting methods for the monitors. CAUTION: Due to safety concerns, it is highly recommended to use the VESA mounting kits provided by IEI for wall, stand and arm mounting.
PAGE 48
DM Series Industrial Monitor DIN Mounting Kit DK-084MS LCD Monitor Arm ARM-11 LCD Monitor Stand STAND-100-RS Table 2-4: DM-84 Mounting Kits 2.5.3 DM-104 Mounting Kits Table 2-5 lists the mounting kits available for the DM-104 monitor. Model DM-104 Panel Mounting Kit PK-104M Rack Mounting Kit RK-104MS-R10 Wall Mounting Kit WK-104MS-R10 DIN Mounting Kit - LCD Monitor Arm ARM-11 LCD Monitor Stand STAND-100-RS Table 2-5: DM-104 Mounting Kits 2.5.
PAGE 49
DM Series Industrial Monitor 2.5.5 DM-150 Mounting Kits Table 2-7 lists the mounting kits available for the DM-150 monitor. Model DM-150 Panel Mounting Kit PK-150M Rack Mounting Kit RK-150MS-R10 Wall Mounting Kit WK-150MS-R10 DIN Mounting Kit - LCD Monitor Arm ARM-31 LCD Monitor Stand STAND-100-RS Table 2-7: DM-150 Mounting Kits 2.5.6 DM-170 Mounting Kits Table 2-8 lists the mounting kits available for the DM-170 monitor.
PAGE 50
DM Series Industrial Monitor 2.5.7 DM-190 Mounting Kits Table 2-9 lists the mounting kits available for the DM-190 monitor. Model DM-190 Panel Mounting Kit PK-190M Rack Mounting Kit RK-190MS-R10 Wall Mounting Kit WK-190MS-R10 DIN Mounting Kit - LCD Monitor Arm ARM-31 LCD Monitor Stand - Table 2-9: DM-190 Mounting Kits 2.
PAGE 51
DM Series Industrial Monitor Figure 2-11: Typical Panel Mounting Table 2-10 lists the number of mounting clamps required to mount the monitor to a panel.
PAGE 52
DM Series Industrial Monitor 2.6.2 Rack and Cabinet Mounting Each model of the DM series industrial monitor has a series of holes located on the rear of the front panel for mounting the monitor to a rack or cabinet. NOTE: 1. The DM-190 monitor requires two special mounting brackets for installation into a rack or cabinet. Refer to Section 5.5.2.2 for details. 2. The DM-84 monitor uses panel mounting clamps for installation into a rack or cabinet. Refer to Section 5.5.1.1 for details. 3.
PAGE 53
DM Series Industrial Monitor Table 2-11 lists the number of holes each monitor has for mounting to a rack or cabinet. Model Holes DM-170 16 DM-150 12 DM-121 8 DM-104 10 Table 2-11: Rack Mounting Clamps 2.6.3 Wall Mounting Each model of the DM series industrial monitor has four holes located on the rear panel for mounting the monitor to a wall. Figure 2-13 shows the typical methods for wall mounting.
PAGE 54
DM Series Industrial Monitor 2.6.4 DIN Rail Mounting The DM-84 and DM-65 have four holes located on the rear panel for mounting the monitor to a DIN rail clamp. Figure 2-14 shows a typical DIN rail mounting bracket.
PAGE 55
DM Series Industrial Monitor 2.6.5 Monitor Arm or Stand Mounting Most models of the DM series industrial monitor have four or eight Video Electronics Standards Association (VESA) standard holes located on the rear panel for mounting the monitor to a monitor arm or stand. NOTE: There is no monitor stand available for the DM-190 monitor. Figure 2-15 shows a typical monitor arm or stand mounting.
PAGE 56
DM Series Industrial Monitor Chapter 3 3 LCD and Touch Panel Specifications Page 56
PAGE 57
DM Series Industrial Monitor 3.1 LCD Specifications 3.1.1 LCD Overview The DM series industrial monitors use the following LCD panels. DM-190: AUO M190EG02 DM-170: AUO M170EG01 DM-150: AUO G150XG01 DM-121: AUO G121SN01 DM-121GX: CHI MEI G121X1-L01 DM-104: Toshiba LTA104D182F DM-084: AUO G084SN03/ Toshiba LTA084C270F DM-65: Toshiba LTA065B0D0F Detailed specifications for the LCD screens are listed in the following sections.
PAGE 58
DM Series Industrial Monitor 3.1.2 DM-190 LCD Specifications Table 3-1 lists the DM-190 LCD specifications. Model DM-190 Size 19” MFR/Model AUO/M190EG02 Resolution SXGA (1280 x 1024) Active Area (mm) 376.3 x 301.1 Pixel Pitch (mm) 0.294 Mode Number of Colors Color Saturation (NTSC%) View Angle (H/V) Brightness (cd/m2) Contrast Ratio Response Time (ms) (at 25C) Power Consumption (W) Interface Supply Voltage (V) TN 16.
PAGE 59
DM Series Industrial Monitor 3.1.3 DM-170 LCD Specifications Table 3-2 lists the DM-170 LCD specifications. Model DM-170 Size 17” MFR/Model AUO/M170EG01 Resolution SXGA (1280 x 1024) Active Area (mm) 337.9 x 270.3 Pixel Pitch (mm) 0.264 Mode Number of Colors Color Saturation (NTSC%) View Angle (H/V) Brightness (cd/m2) Contrast Ratio Response Time (ms) (at 25C) Power Consumption (W) Interface Supply Voltage (V) TN 16.2M 72 140/130 300 500:1 8 25.
PAGE 60
DM Series Industrial Monitor 3.1.4 DM-150 LCD Specifications Table 3-3 lists the DM-150 LCD specifications. Model DM-150 Size MFR/Model 15” AUO/G150XG01 XGA (1024 x Resolution 768) Active Area (mm) 304.1 x 228.1 Pixel Pitch (mm) 0.297 Mode TN Number of Colors 262K Color Saturation (NTSC%) View Angle (H/V) 60 130/120 Brightness (cd/m2) 350 Contrast Ratio 500:1 Response Time (ms) (at 25C) 12 Power Consumption (W) Interface 11.5 1ch LVDS Supply Voltage (V) 3.
PAGE 61
DM Series Industrial Monitor 3.1.5 DM-121 LCD Specifications Table 3-4 lists the DM-121 LCD specifications. Model DM-121G DM-121GX 12.1” 12.1” MFR/Model AUO/G121SN01 CHE MEI/G121X1-L01 Resolution SVGA (800 x 600) XGA (1024 x 768) Active Area (mm) 246.0 x 184.5 245.76 x 184.32 Pixel Pitch (mm) 0.307 0.240 TN TN Number of Colors 262K 262K View Angle (H/V) 150/110 160/160 400 450 500:1 700:1 Response Time (ms) (at 25C) 35 13 (TR); 12 (TF) Power Consumption (W) 7.3 3.
PAGE 62
DM Series Industrial Monitor 3.1.6 DM-104 LCD Specifications Table 3-5 lists the DM-104 LCD specifications. Model DM-104 10.4” Size MFR/Model Toshiba/LTA104D182F Resolution SVGA (800 x 600) Active Area (mm) 211.2 x 158.4 Pixel Pitch (mm) 0.264 TN Mode Number of Colors 262K View Angle (H/V) 120 / 100 400 Brightness (cd/m2) 500:1 Contrast Ratio Response Time (ms) (at 25C) 6 (tON), 17 (tOFF) Interface Supply Voltage (V) 1ch LVDS 3.
PAGE 63
DM Series Industrial Monitor 3.1.7 DM-84 LCD Specifications Table 3-6 lists the DM-84 LCD specifications. Model DM-84 Size 8.4” MFR/Model Toshiba/LTA084C270F Resolution SVGA (800 x 600) Active Area (mm) 170.4 x 127.8 Pixel Pitch (mm) 0.213 TN Mode Number of Colors 262K View Angle (H/V) 120 / 100 400 Brightness (cd/m2) 450:1 Contrast Ratio Response Time (ms) (at 25C) 8 (tON), 17 (tOFF) Interface Supply Voltage (V) 1ch LVDS 3.
PAGE 64
DM Series Industrial Monitor 3.1.8 DM-65 LCD Specifications Table 3-7 lists the DM-65 LCD specifications. Model DM-65 Size 6.5” MFR/Model Toshiba/LTA065B0D0F Resolution VGA (640 x 480) Active Area (mm) 132.48 x 99.36 Pixel Pitch (mm) 0.207 Mode Number of Colors 262K Color Saturation (NTSC%) View Angle (H/V) Brightness (cd/m2) Contrast Ratio 140/120 400 500:1 Response Time (ms) (at 25C) 25 Power Consumption (W) 4.2 Interface Supply Voltage (V) 3.
PAGE 65
DM Series Industrial Monitor 3.2 Optional Touch Panels IEI offers optional touch panels for the DM series industrial monitors with the following features: Small border customized design All size touch panel design Customized activation force and palm rejection Customized optical characteristics High reliability and durability in the field 3.2.1 Touch Panel Models Table 3-8 lists the DM series industrial monitors and their associated touch panels.
PAGE 66
DM Series Industrial Monitor 3.2.2 Touch Panel Dimensions Table 3-9 shows the touch panel dimensions in millimeters. Model: Dimension Dimensional PanJit 1190503A 1171505A 2.8 Viewing Area: 306.05 381.3 - Active Area: 301.05 376.3 - Key Area: 300.05 375.3 - 365 295.08 2.9 Viewing Area: 342.05 275.45 - Active Area: 342.05 275.45 - 338.0 271.4 - 257.5 333.6 2.9 Viewing Area: 232.1 308.2 - Active Area: 228.1 304.1 - 204 268 2.
PAGE 67
DM Series Industrial Monitor Viewing Area: 139.00 106.00 - Active Area: 133.00 99.80 - Table 3-9: Touch Panel Dimensions (mm) 3.2.3 Touch Panel Specifications Table 3-10 lists the touch panel specifications. Type Analog Resistive Type Touch Panel Input Method Finger, Stylus or gloved hand Wire Type 5-wire Maximum Voltage and Currant DC7V Position Accuracy Less than 1.
PAGE 68
DM Series Industrial Monitor OS Compatibility Windows: XP/XP Embedded Windows 2000 Windows ME Windows 98 SE Windows CE.Net 4.2 (x86 and ARM) WHQL certified Linux: Fedora Core I/II Mandrake 10.0/10.1 RedHat 9.
PAGE 69
DM Series Industrial Monitor 3.2.4 Touch Panel RS-232 Controller Specifications Table 3-11 lists the touch panel RS-232 controller specifications. Circuit Board Dimension 20mm x 75mm (0.79inches x 2.95inches)----(5-Wire) Power Requirements D.C.
PAGE 70
DM Series Industrial Monitor 3.2.5 Touch Panel USB Controller Specifications Table 3-12 lists the touch panel USB controller specifications. Circuit Board Dimension 20mm x 75mm (0.79inches x 2.95inches)----(5-Wire) Power Requirements D.C.+5V (100mA typical, 50mV peak to peak maximum ripple and noise) Operating Temperature 0°C to 50°C Storage Temperature -40°C to 80°C Relative Humidity 95% at 60°C Interface USB 1.
PAGE 71
DM Series Industrial Monitor 3.3 Power Adapters Table 3-13 lists the AC/DC power adapter specifications.
PAGE 72
DM Series Industrial Monitor Chapter 4 4 AD Boards Page 72
PAGE 73
DM Series Industrial Monitor 4.1 AD Board Overview The DM series industrial monitor AD board provides a wide variety of control interfaces, receiving and managing interface signals from a CPU card through cabling. There are three AD boards used for the DM series monitors: AV-9350, AV-5350 and AV-5300. Refer to Table 1-2 for a listing of DM series monitors and their associated AD board. The following sections describe each AD board in detail. 4.
PAGE 74
DM Series Industrial Monitor 1 x TTL output connector 2 x 5V power connector 1 x RS-232 connector The AV-9350 AD board has the following connectors on the board rear panel: 1 x RS-232 connector 1 x VGA connector 1 x 12V DC power connector The locations of the peripheral interface connectors for the AV-9350 AD board are shown in Section 4.2.3. A complete list of all the peripheral interface connectors can be seen in Section 4.2.4. 4.2.
PAGE 75
DM Series Industrial Monitor 4.2.4 AV-9350 Peripheral Interface Connectors Table 4-1 shows a list of the peripheral interface connectors on the AV-9350 AD board. Detailed descriptions of these connectors can be found in Section 4.2.7.
PAGE 76
DM Series Industrial Monitor 4.2.6 AV-9350 Onboard Jumper Table 4-3 lists the onboard jumper. A detailed description of the jumper can be found in Section 4.2.19. Jumper Type Label LCD Panel Voltage Select 3-pin header JP5 Table 4-3: AV-9350 Onboard Jumper 4.2.7 AV-9350 Internal Peripheral Connectors Internal peripheral connectors on the AV-9350 AD board are only accessible when the board is outside of the monitor.
PAGE 77
DM Series Industrial Monitor 4.2.8 5V Power Connector CN Label: CN11, CN12 CN Type: 2-pin header CN Pinouts: See Table 4-4 CN Location: See Figure 4-3 The 5V power connector is a general-purpose power connector.
PAGE 78
DM Series Industrial Monitor 4.2.9 Debugged Port Connector CN Label: CN3, CN5 CN Type: 4-pin header CN Pinouts: See Table 4-5 CN Location: See Figure 4-4 Use the debugged port connector to update the AD board BIOS.
PAGE 79
DM Series Industrial Monitor 4.2.10 External OSD and LED Indication Connector CN Label: CN4 CN Type: 9-pin header CN Pinouts: See Table 4-6 CN Location: See Figure 4-5 The External OSD and LED Indication connector connects to an external OSD controller.
PAGE 80
DM Series Industrial Monitor Figure 4-5: External OSD and LED Indication Connector Location 4.2.11 Serial Communications Connector CN Label: COM1 CN Type: 10-pin header CN Pinouts: See Table 4-7 CN Location: See Figure 4-6 The AV-9350 has a 10-pin serial communications connector.
PAGE 81
DM Series Industrial Monitor Figure 4-6: Serial Communications Connector Location Page 81
PAGE 82
DM Series Industrial Monitor 4.2.12 TTL Output Connector CN Label: CN7 CN Type: 40-pin header CN Pinouts: See Table 4-8 CN Location: See Figure 4-7 The TTL output connector connects the LCD panel to the system.
PAGE 83
DM Series Industrial Monitor 2 6 2 8 3 0 3 2 3 4 3 6 3 8 4 0 R1 R3 R5 R7 GROUND FPVS FPHS ENVEE 2 5 2 7 2 9 3 1 3 3 3 5 3 7 3 9 R0 R2 R4 R6 GROUND FPCLK FPDEN N/C Table 4-8: TTL Output Connector Pinouts Figure 4-7: TTL Output Connector Location Page 83
PAGE 84
DM Series Industrial Monitor NOTE: The supply voltage (3.3V and 5V) can be selected via JP5. 4.2.13 VGA Connector CN Label: CN2 CN Type: 10-pin header CN Pinouts: See Table 4-9 CN Location: See Figure 4-8 In addition to the standard DB-15 female VGA connector (CN1), a VGA connection can also be made through the onboard CN2 10-pin header.
PAGE 85
DM Series Industrial Monitor Figure 4-8: VGA Connector Location 4.2.14 AV-9350 External (Rear Panel) Connectors Figure 4-9 shows the AV-9350 external (rear panel) connectors. The peripheral connectors on the back panel of the monitor can connect to external devices.
PAGE 86
DM Series Industrial Monitor 4.2.15 DC 12V Connector CN Label: J2 CN Type: DC 12V Jack CN Pinouts: See Table 4-10 CN Location: See Figure 4-9 Use the DC 12V connector to power the monitor. PI N DESCRIPTION 1 GND 2 GND 3 DC 12V Table 4-10: DC 12V Connector Pinouts 4.2.16 RS232 Serial Connector CN Label: J1 CN Type: D-Sub 9 female connector CN Pinouts: See Table 4-11 and Figure 4-10 CN Location: See Figure 4-9 Use the RS-232 serial connector to connect the touch panel.
PAGE 87
DM Series Industrial Monitor 5 GND Table 4-11: RS232 Serial Connector Pinouts Figure 4-10: RS232 Serial Connector Pinout Locations 4.2.17 OSD Control Buttons CN Label: JP1, JP2, JP3, JP4 CN Type: Pushbutton CN Pinouts: See Table 4-12, Table 4-13, Table 4-14, Table 4-15 CN Location: See Figure 4-9 Use these buttons to control the OSD functions. The following tables list each button’s function and pinouts.
PAGE 88
DM Series Industrial Monitor PI PI DESCRIPTION N N DESCRIPTION DOWN/AUTO 1 ADJUST 3 No Connect 2 Ground 4 No Connect Table 4-14: OSD Control Button JP3 Pinouts PI PI DESCRIPTION N N DESCRIPTION 1 LCD ON/OFF 3 No Connect 2 Ground 4 No Connect Table 4-15: OSD Control Button JP4 Pinouts 4.2.
PAGE 89
DM Series Industrial Monitor Table 4-16: VGA Connector Pinouts Figure 4-11: VGA Connector Pinout Locations 4.2.19 AV-9350 Onboard Jumper NOTE: A jumper is a metal bridge used to close an electrical circuit. It consists of two or three metal pins and a small metal clip (often protected by a plastic cover) that slides over the pins to connect them.
PAGE 90
DM Series Industrial Monitor Figure 4-13: Jumper Location Page 90
PAGE 91
DM Series Industrial Monitor 4.2.20 LCD Panel (TTL) Voltage Select Jumper Jumper Label: JP5 Jumper Type: 3-pin header Jumper Location: See Figure 4-13 Jumper Settings: See Table 4-17 The JP5 jumper sets the voltage to the LCD panel. JP 5 1- Description Panel Voltage select 5V 2 2- Panel Voltage select 3.
PAGE 92
DM Series Industrial Monitor 4.3 AV-5350 AD Board The following sections describe the AV-5350 AD board in detail. 4.3.1 AV-5350 AD Board Overview Figure 4-14: AV-5350 AD Board Overview 4.3.
PAGE 93
DM Series Industrial Monitor 1 x 12V power connector 1 x Backlight Inverter connector The AV-5350 AD board has the following connectors on the board rear panel: 1 x VGA connector 1 x 12V DC power connector The locations of the peripheral interface connectors for the AV-5350 AD board are shown in Section 4.3.3. A complete list of all the peripheral interface connectors can be seen in Section 4.3.4. 4.3.
PAGE 94
DM Series Industrial Monitor 4.3.4 AV-5350 Peripheral Interface Connectors Table 4-18 shows a list of the peripheral interface connectors on the AV-5350 AD board. Detailed descriptions of these connectors can be found in Section 4.3.7.
PAGE 95
DM Series Industrial Monitor Jumper Type Label LCD Panel Voltage Select 3-pin header JP1 Table 4-20: AV-5350 Onboard Jumper 4.3.7 AV-5350 Internal Peripheral Connectors Internal peripheral connectors on the AV-5350 AD board are only accessible when the board is outside of the monitor. This section has complete descriptions of all the internal, peripheral connectors on the AV-5350 AD board. 4.3.
PAGE 96
DM Series Industrial Monitor Figure 4-16: 5V Power Connector Location 4.3.9 12V Power Connector CN Label: CN7 CN Type: 2-pin header CN Pinouts: See Table 4-22 CN Location: See Figure 4-17 The 12V power connector is a general-purpose power connector.
PAGE 97
DM Series Industrial Monitor Figure 4-17: 12V Power Connector Location 4.3.10 Backlight Inverter Connector CN Label: CN6 CN Type: 6-pin header CN Pinouts: See Table 4-23 CN Location: See Figure 4-18 The Inverter connector connects to the LCD backlight.
PAGE 98
DM Series Industrial Monitor Figure 4-18: Backlight Inverter Connector Location 4.3.11 External OSD and LED Indication Connector CN Label: CN2 CN Type: 9-pin header CN Pinouts: See Table 4-24 CN Location: See Figure 4-19 The External OSD and LED Indication connector connects to an external OSD controller.
PAGE 99
DM Series Industrial Monitor 7 AUTO 8 LCD ON/OFF 9 GND Table 4-24: External OSD and LED Indication Connector Pinouts Figure 4-19: External OSD and LED Indication Connector Location 4.3.12 LVDS Output Connector CN Label: CN5 CN Type: 30-pin header CN Pinouts: See Table 4-25 CN Location: See Figure 4-20 Use the LVDS output connector to connect the LCD panel to a system.
PAGE 100
DM Series Industrial Monitor 11 TXO0+ 12 TXO0- 13 GND 14 GND 15 TXE3+ 16 TXE3- 17 TXEC+ 18 TXEC- 19 TXE2+ 20 TXE2- 21 TXE1+ 22 TXE1- 23 TXE0+ 24 TXE0- 25 GND 26 GND 27 VDD 28 VDD 29 VDD 30 VDD Table 4-25: LVDS Output Connector Pinouts Figure 4-20: LVDS Output Connector Location NOTE: The supply voltage (3.3V (Default), 5V or 12V) can be selected via JP1.
PAGE 101
DM Series Industrial Monitor 4.3.13 VGA Connector CN Label: J2 CN Type: 10-pin header CN Pinouts: See Table 4-26 CN Location: See Figure 4-21 In addition to the standard DB-15 female VGA connector (J1), a VGA connection can also be made through the onboard CN2 10-pin header.
PAGE 102
DM Series Industrial Monitor Figure 4-21: VGA Connector Location 4.3.14 AV-5350 External (Rear Panel) Connectors Figure 4-22 shows the AV-5350 external (rear panel) connectors. The peripheral connectors on the back panel of the monitor can connect to external devices.
PAGE 103
DM Series Industrial Monitor 4.3.15 DC 12V Connector CN Label: J3 CN Type: DC 12V Jack CN Pinouts: See Table 4-27 CN Location: See Figure 4-22 Use the DC 12V connector to power the monitor. PI DESCRIPTIO N N 1 GND 2 GND 3 DC 12V Table 4-27: DC 12V Connector Pinouts 4.3.
PAGE 104
DM Series Industrial Monitor PIN DESCRIPTION PIN DESCRIPTION 6 Ground 14 Vertical Synchronization 7 Ground 15 DDC Clock 8 Ground Table 4-28: VGA Connector Pinouts Figure 4-23: VGA Connector Pinout Locations 4.3.17 AV-5350 Onboard Jumper NOTE: A jumper is a metal bridge used to close an electrical circuit. It consists of two or three metal pins and a small metal clip (often protected by a plastic cover) that slides over the pins to connect them.
PAGE 105
DM Series Industrial Monitor Figure 4-25: Jumper Location 4.3.18 LCD Panel Voltage Select Jumper Jumper Label: JP5 Jumper Type: 6-pin header Jumper Location: See Figure 4-25 Jumper Settings: See Table 4-29 The JP1 jumper sets the voltage to the LCD panel. JP1 Description 1-2 Panel Voltage select 3.
PAGE 106
DM Series Industrial Monitor 4.4 AV-5300 AD Board Overview The AV-5300 AD board provides a wide variety of control interfaces, receiving and managing interface signals from a CPU card through cabling. The following sections describe the AV-5300 AD board in detail.
PAGE 107
DM Series Industrial Monitor 4.4.
PAGE 108
DM Series Industrial Monitor 4.4.2 AV-5300 AD Board Layout Figure 4-27 shows the on-board peripheral connectors and on-board jumpers.
PAGE 109
DM Series Industrial Monitor 4.4.3 AV-5300 Peripheral Interface Connectors Table 4-30 shows a list of the peripheral interface connectors on the AV-5300 AD board. Detailed descriptions of these connectors can be found in Section 4.4.6.
PAGE 110
DM Series Industrial Monitor 4.4.5 AV-5300 On-board Jumpers Table 4-32 lists the on-board jumpers. A detailed description of these jumpers can be found in Section 4.4.15. Jumper Type Label LCD Panel Power Input Select 6-pin header JP4 LCD Panel Voltage Select 6-pin header JP1 Table 4-32: AV-5300 On-board Jumpers 4.4.6 AV-5300 Internal Peripheral Connectors Internal peripheral connectors on the AV-5300 AD board are only accessible when the board is outside of the monitor.
PAGE 111
DM Series Industrial Monitor Table 4-33: Auto-dimming Connector Pinouts Figure 4-28: Auto-dimming Connector Location 4.4.8 Debug Port Connector CN Label: CN4 CN Type: 4-pin wafer connector CN Pinouts: See Table 4-34 CN Location: See Figure 4-29 Use the debug port connector to update the AD board BIOS.
PAGE 112
DM Series Industrial Monitor Figure 4-29: Debug Port Connector Location 4.4.9 External OSD and LED Indication Connector CN Label: CN3 CN Type: 9-pin wafer connector CN Pinouts: See Table 4-35 CN Location: See Figure 4-30 The External OSD and LED Indication connector connects to an external OSD controller.
PAGE 113
DM Series Industrial Monitor Figure 4-30: External OSD and LED Indication Connector Location 4.4.10 Backlight Inverter Connector CN Label: CN2 CN Type: 6-pin wafer connector CN Pinouts: See Table 4-36 CN Location: See Figure 4-31 The Inverter connector connects to the LCD backlight. Using the BKLT_EN signal to control the inverter status (ON/OFF) and the BKLT_ADJ signal to adjust brightness of inverter by OSD brightness function.
PAGE 114
DM Series Industrial Monitor Figure 4-31: Backlight Inverter Connector Location 4.4.11 LVDS Output Connector CN Label: CN8 CN Type: 30-pin connector CN Pinouts: See Table 4-37 CN Location: See Figure 4-32 Use either LVDS output connector to connect the LCD panel to a system.
PAGE 115
DM Series Industrial Monitor PIN DESCRIPTION PIN DESCRIPTION 23 TXE0+ 24 TXE0- 25 GND 26 GND 27 VDD 28 VDD 29 VDD 30 VDD Table 4-37: LVDS Output Connector Pinouts Figure 4-32: LVDS Output Connector Location NOTE: The supply voltage (3.3V (Default), 5V or 12V) can be selected via JP1. 4.4.
PAGE 116
DM Series Industrial Monitor The AV-5300 supports two power output connectors, one for 12V and the other for 5V. PIN DESCRIPTION 1 +12V 2 GND Table 4-38: Power Output Connector Pinouts (CN12) PIN DESCRIPTION 1 +5V 2 GND Table 4-39: Power Output Connector Pinouts (CN13) Figure 4-33: Power Output Connector Locations 4.4.
PAGE 117
DM Series Industrial Monitor The AV-5300 supports two internal power input connectors.
PAGE 118
DM Series Industrial Monitor 4.4.14 VGA Connector CN Label: J1 CN Type: 10-pin box header CN Pinouts: See Table 4-42 CN Location: See Figure 4-35 In addition to the standard DB-15 female VGA connector (J1), a VGA connection can also be made through the on-board CN2 10-pin header.
PAGE 119
DM Series Industrial Monitor 4.4.15 AV-5300 On-board Jumpers NOTE: A jumper is a metal bridge used to close an electrical circuit. It consists of two or three metal pins and a small metal clip (often protected by a plastic cover) that slides over the pins to connect them. To CLOSE/SHORT a jumper means connecting the pins of the jumper with the plastic clip and to OPEN a jumper means Figure 4-36: Jumpers removing the plastic clip from a jumper. The AV-5300 has two on-board jumpers (Table 4-32).
PAGE 120
DM Series Industrial Monitor 4.4.16 LCD Panel Power Input Jumper Jumper Label: JP4 Jumper Type: 6-pin header Jumper Location: See Figure 4-37 Jumper Settings: See Table 4-43 The JP4 jumper sets the input source from either the 12V power connector (J3) or the external terminal block. JP4 Description 1-3, 2-4 3-5, 4-6 +12V from power connector (J3) (Default) Input with external connector (Need external power module) Table 4-43: LCD Panel Power Input Jumper Settings 4.4.
PAGE 121
DM Series Industrial Monitor 4.4.18 AV-5300 External (Rear Panel) Connectors Figure 4-38 shows the AV-5300 external (rear panel) connectors. The peripheral connectors on the back panel of the monitor can connect to external devices. The peripheral connectors on the rear panel are: 1 x DC 12V connector 1 x DVI-D connector 1 x VGA connector Figure 4-38: AV-5300 External (Rear Panel) Connectors 4.4.
PAGE 122
DM Series Industrial Monitor 4.4.20 VGA Connector CN Label: J5 CN Type: D-sub 15 female connector CN Pinouts: See Table 4-46 and Figure 4-39 CN Location: See Figure 4-38 Use the standard D-sub 15-pin VGA connector to connect the monitor to a system.
PAGE 123
DM Series Industrial Monitor 4.4.21 DVI-D Connector CN Label: J2 CN Type: D-sub DVI female connector CN Pinouts: See Table 4-47 and Figure 4-40 CN Location: See Figure 4-38 The 24-pin female dual link digital only DVI [Digital Visual Interface] connector is a standard for high-speed, high-resolution digital displays. Use the DVI-D connector to connect the LCD to a system.
PAGE 124
DM Series Industrial Monitor Figure 4-40: DVI-D Connector Pinout Locations Chapter 4 5 5 Installation Page 124
PAGE 125
DM Series Industrial Monitor 5.1 Installation Precautions When installing the DM series industrial monitor, please follow the precautions listed below: Read the user manual: The user manual provides a complete description of the DM series industrial monitor, installation instructions and configuration options. DANGER! Disconnect Power: Power to the monitor must be disconnected when installing the DM series industrial monitor, or before any attempt is made to access the rear panel.
PAGE 126
DM Series Industrial Monitor 5.2 Unpacking 5.2.1 Packaging When shipped, the DM series industrial monitor is wrapped in a plastic bag. Two polystyrene ends are placed on either side of the monitor. The monitor is then placed into a first (internal) cardboard box. This box is then sealed and placed into a second (external) cardboard box. The second box is also sealed. A bag containing accessory items is placed underneath the monitor, at the bottom of the internal (first) box. 5.2.
PAGE 127
DM Series Industrial Monitor Step 7: Make sure all the components listed in the packing list are present. Step 0: 5.2.3 Packing List All the monitors in the DM series are shipped with the following components: 1 x DM-190/170/150/121/104/84/65 series industrial monitor.
PAGE 128
DM Series Industrial Monitor 5.3.2 Voltage Select Jumper Settings If the monitor comes with both 12V and 9~36V DC power connectors, the voltage select jumper on the integrated AD board must be configured for the DC connector that is used to power the monitor. Refer to Chapter 4 for the appropriate jumper settings of each AD board. NOTE: The default voltage select jumper is configured for a 12V power source.
PAGE 129
DM Series Industrial Monitor 5.4 Connectors Table 5-1 lists the rear panel connectors for the DM series industrial monitors.
PAGE 130
DM Series Industrial Monitor 5.4.1 Rear Panel Connectors Overview Figure 5-1: Monitor Rear Panel Connections Figure 5-1 shows all the possible rear panel connectors for the DM series industrial monitor. Refer to Table 5-1 for a list of the monitors and their corresponding connectors. The following sections fully describe the rear panel connectors for the DM series industrial monitor. 5.4.
PAGE 131
DM Series Industrial Monitor Table 5-2: VGA Connector Pinouts Figure 5-2: VGA Connector 5.4.3 DVI-D Connector Use the rear panel standard 24-pin female DVI-D connector to connect the monitor to the system graphics interface.
PAGE 132
DM Series Industrial Monitor Figure 5-4: 12V Power Connector 5.4.5 Optional DC Power Connector Use the rear panel 3-pin terminal block DC power connector to connect the monitor to a DC power source. Figure 5-5: DC Power Connector 5.4.6 Optional RS-232 Touch Panel Connector Use the rear panel standard RS-232 DB-9 female touch panel connector to connect the monitor to the system graphics interface.
PAGE 133
DM Series Industrial Monitor Figure 5-6: Optional RS-232 Touch Panel Connector 5.4.7 Optional USB Touch Panel Connector Use the rear panel standard USB touch panel connector to connect the monitor to the system graphics interface.
PAGE 134
DM Series Industrial Monitor 5.5 Mounting the DM Series Industrial Monitor The DM series industrial monitor can be mounted in a panel, cabinet, rack, DIN rail or wall. The monitor can also be mounted on a monitor arm or stand. The mounting methods are described below. CAUTION: When mounting the monitor take care to tighten the retention screws or bolts until fully secure, but do not over tighten. Over tightening the retention screws or bolts may cause them to become stripped, rendering them useless. 5.5.
PAGE 135
DM Series Industrial Monitor Figure 5-8: Panel Opening Step 3: Slide the monitor through the hole until the metal frame is flush against the panel (Figure 5-9). Figure 5-9: Insert the Monitor Step 4: Insert the panel mounting clamps into the pre-formed holes along the edges of the monitor, behind the metal frame.
PAGE 136
DM Series Industrial Monitor required number of mounting clamps. Figure 5-10: Panel Mounting Clamp Position Step 5: Tighten the screws that pass through the panel mounting clamps until the plastic caps at the front of all the screws are firmly secured to the panel (Figure 5-10). Step 3: 5.5.1.2 DM-65 Panel Mounting To mount the DM-65 monitor into a panel, follow steps one through three of the standard panel mounting procedure (Section 5.5.1.1), then continue using the steps below.
PAGE 137
DM Series Industrial Monitor Figure 5-11: DM-65 Panel Mounting Step 5: Tighten the panel retention screws that pass through the panel mounting clips until the plastic caps at the front of all the screws are firmly secured to the panel (Figure 5-11). Step 0: 5.5.2 Cabinet and Rack Installation 5.5.2.
PAGE 138
DM Series Industrial Monitor NOTE: When purchasing a cabinet/rack installation bracket, make sure it is compatible with both the monitor and the cabinet/rack into which the monitor is installed. Step 2: Slide the monitor through the cabinet/rack bracket until the rear side of the monitor frame is flush against the front of the bracket. Step 3: Make sure the retention screw holes at the rear of the monitor frame are aligned with the retention screw holes in the cabinet/rack bracket.
PAGE 139
DM Series Industrial Monitor (Figure 5-13). Figure 5-13: Install into a Cabinet/Rack Step 6: Once the monitor with the attached cabinet/rack has been properly inserted into the rack or cabinet, secure the front of the rack/cabinet bracket to the front of the rack or cabinet (Figure 5-13).
PAGE 140
DM Series Industrial Monitor 5.5.2.2 DM-190 Cabinet and Rack Installation To mount the DM-190 monitor into a cabinet/rack, please follow the steps below. Step 1: Insert and tighten the supplied mounting nuts and bolts to the rack for the rack mounting bracket. Each bracket requires three nuts and bolts for installation. (See Figure 5-14) Figure 5-14: Rack Mounting Nuts and Bolts Installation (DM-190) Step 2: Secure the rack mounting bracket to two sides of the monitor using the supplied retention screws.
PAGE 141
DM Series Industrial Monitor Figure 5-15: Rack Mounting Bracket Installation (DM-190) Step 3: Carefully insert the slotted holes of the brackets on the monitor through the bolts on the rack and gently pull the monitor downwards until the bolts rests securely in the slotted holes. (See Figure 5-16). Ensure that all six of the bolts fit snuggly into their respective slotted holes.
PAGE 142
DM Series Industrial Monitor Figure 5-16: Rack Mounting (DM-190) 5.5.2.3 DM-84 and DM-65 Cabinet and Rack Installation Use the standard panel mounting procedure (Section 5.5.1.1) to mount the DM-84 monitor into a cabinet/rack and use the DM-65 panel mounting procedure (Section 5.5.1.2) to mount the DM-65 monitor into a cabinet/rack.
PAGE 143
DM Series Industrial Monitor 5.5.3 DIN Rail Installation To mount the DM series industrial monitor onto a DIN rail, please follow the steps below. Step 1: Attach the DIN rail mounting bracket to the rear of the monitor. Secure the bracket to the monitor with the supplied retention screws (Figure 5-17). Figure 5-17: DIN Rail Mounting Bracket Step 2: Make sure the inserted screw in the center of the bracket is at the lowest position of the elongated hole (Figure 5-18).
PAGE 144
DM Series Industrial Monitor Step 3: Place the DIN rail flush against the back of the mounting bracket making sure the edges of the rail are between the upper and lower clamps (Figure 5-19). Figure 5-19: Mounting the DIN RAIL Step 4: Secure the DIN rail to the mounting bracket by turning the top screw clockwise. This draws the lower clamp up and secures the monitor to the DIN rail (Figure 5-20).
PAGE 145
DM Series Industrial Monitor 5.5.4 Wall Mounting CAUTION: Due to safety concerns, it is highly recommended to use the VESA mounting kits provided by IEI for wall, stand and arm mounting. If the VESA mounting kit is purchased separately, please make sure the mounting kit is UL-listed. To mount the DM series industrial monitor onto a wall, please follow the steps below. Step 1: Select a location on the wall for the wall-mounting bracket.
PAGE 146
DM Series Industrial Monitor mounting kit into the four screw holes on the real panel of the monitor and tighten until the screw shank is secured against the rear panel (Figure 5-22). Figure 5-22: Monitor Support Screws Step 7: Align the mounting screws on the monitor rear panel with the mounting holes on the bracket. Step 8: Carefully insert the screws through the holes and gently pull the monitor downwards until the monitor rests securely in the slotted holes (Figure 5-23).
PAGE 147
DM Series Industrial Monitor Figure 5-23: Wall Mounting the Monitor 5.5.5 Monitor Stand Installation The DM series industrial monitor has Video Electronics Standards Association (VESA) standard mounting holes tapped into the rear panel. The standard holes are M4 set at 100m x 100mm apart (Figure 5-24).
PAGE 148
DM Series Industrial Monitor Figure 5-24: VESA Mounting Holes The monitor stand mounting plate has a matching VESA hole pattern. To mount the DM series industrial monitor onto a stand, please follow the steps below. Step 1: Line up the threaded holes on the monitor rear panel with the screw holes on the monitor stand mounting plate. Step 2: Secure the monitor to the stand with the supplied retention screws (Figure 5-25).
PAGE 149
DM Series Industrial Monitor Figure 5-25: Monitor Stand Mounting 5.5.6 Monitor Arm Installation The DM series industrial monitor has Video Electronics Standards Association (VESA) standard mounting holes tapped into the rear panel. The standard holes are M4 set at 100m x 100mm apart (Figure 5-24). The monitor arm mounting plate has a matching VESA hole pattern. To mount the DM series industrial monitor onto a monitor arm, please follow the steps below.
PAGE 150
DM Series Industrial Monitor Figure 5-26: Monitor Arm Mounting Page 150
PAGE 151
DM Series Industrial Monitor THIS PAGE IS INTENTIONALLY LEFT BLANK Page 151
PAGE 152
DM Series Industrial Monitor Chapter 6 6 On-Screen-Display (OSD) Controls Page 152
PAGE 153
DM Series Industrial Monitor 6.1 User Mode OSD Structure 6.1.1 OSD Buttons There are several on-screen-display (OSD) control buttons oriented either vertically along the right hand side or horizontally along the bottom of the monitor front panel. Refer to Section 2.2 for availability and orientation of the OSD controls on specific DM series monitors. Figure 6-1 shows a typical arrangement of OSD controls for all models of the DM series industrial monitor except the DM-65.
PAGE 154
DM Series Industrial Monitor Figure 6-2 shows the OSD controls for the DM-65. Figure 6-2: DM-65 OSD Control Buttons 6.1.2 OSD Menu Structure Table 6-1 shows the OSD menu structure for all models of the DM series LCD monitor. Level 0 Level 1 Value Main Display Features Menu Brightness 0 to 100 Contrast 0 to 100 Horizontal Size 0 to 100 Sharpness 1 to 5 Volume This menu is currently disabled, Mute and will be implemented with Speaker Menu models equipped with speakers.
PAGE 155
DM Series Industrial Monitor Image Setting Menu OSD Menu Signal Menu Auto Color Select Width 0 to 100 Phase 0 to 100 H. Position 0 to 100 V.
PAGE 156
DM Series Industrial Monitor 6.2 Using the OSD OSD menu options are described below. 6.2.1 Main Display Features Main display features are shown in Figure 6-3. Figure 6-3: Main Display Features Brightness: The brightness option adjusts the brightness of screen. This function adjusts the offset value of ADC. Setting this value too high or too low will affect the quality of image. Contrast: This function adjusts the gain value of ADC.
PAGE 157
DM Series Industrial Monitor 6.2.2 Gamma Gamma options are shown in Figure 6-5. Figure 6-4: Color Options The Gamma menu adjusts the gamma for the LCD. Volume: This item adjusts the volume. It is only implemented with models equipped with speakers. Mute: This item mute the audio. It is only implemented with models equipped with speakers. Gamma: This item allows user to calibrate the monitor by hardware.
PAGE 158
DM Series Industrial Monitor 6.2.3 Color Color options are shown in Figure 6-5. Figure 6-5: Color Options The Color menu fine-tunes the palette of color hues for the LCD. 9300k: NTSC standard Kelvin 7500k: NTSC standard Kelvin 6500k: NTSC standard Kelvin User Temp: This item allows fine-tuning the balance among Red, Green, and Blue color hues if images look garish or unrealistic.
PAGE 159
DM Series Industrial Monitor 6.2.4 Image Settings The image settings are shown in Figure 6-6. Figure 6-6: Image Settings Menu Image settings are described below. Auto Color: Automatically adjusts the color settings. Width: Adjusts the width of the display screen. Phase: Adjusts the input signal and dot clock position (Analog only). H. Position: Adjusts the horizontal position of the display screen. V.
PAGE 160
DM Series Industrial Monitor Adjusts the vertical position of the display screen. 6.2.5 OSD Configurations The OSD configurations are shown in Figure 6-7. Figure 6-7: OSD Configurations Menu OSD Configurations are described below. OSD Time Out: Determines how many seconds the OSD screen stays on screen before it disappears when OSD is left unattended. OSD Position: Adjusts the OSD position on the screen.
PAGE 161
DM Series Industrial Monitor 6.2.
PAGE 162
DM Series Industrial Monitor THIS PAGE IS INTENTIONALLY LEFT BLANK Page 162
PAGE 163
DM Series Industrial Monitor Chapter 7 7 Software Drivers Page 163
PAGE 164
DM Series Industrial Monitor 7.1 Introduction The touch panel controller enables analog resistive touch panels for four-wire, five-wire & eight-wire models. The controller directly communicates with the PC system through the touch panel communications interface. The controller design is superior in sensitivity, accuracy, and friendly operation. The touch panel driver emulates the left mouse button and the right mouse button functions.
PAGE 165
DM Series Industrial Monitor Figure 7-1: Driver CD Pop Up Screen Step 3: Select the operating system installed on the system from the menu on the left side of the screen. NOTE: The following description is for driver installation using a Windows 2000 OS. If a different OS is installed, please refer to the driver user manual for the relevant OS. The driver user manuals can be accessed by selecting “User Manual” from the menu on the left side of the “Driver CD Pop Up Screen”.
PAGE 166
DM Series Industrial Monitor Figure 7-2: Install Shield Wizard Preparation Step 5: After the Install Shield Wizard is ready, a welcome screen appears (Figure 7-3). Figure 7-3: Welcome Screen Step 6: To continue the installation process click NEXT. Step 7: An Install PS/2 interface driver screen appears (Figure 7-4). It is not necessary to install the PS/2 interface driver. To continue click NEXT.
PAGE 167
DM Series Industrial Monitor Figure 7-4: Install PS/2 Interface Driver Step 8: Four point calibration options are then selected. Four point calibrations can be done every time a user boots up, during the next time the system boots or never. Select if and when a four-point calibration should be done. Click NEXT to continue.
PAGE 168
DM Series Industrial Monitor Figure 7-5: Install PS/2 Interface Driver Step 9: The user is then prompted to ensure the touch monitor or the USB for the touch controller is plugged into the system (Figure 7-6). Once the touch controller is plugged into the system, click “OK.” Figure 7-6: Touch Monitor/USB Touch Controller Confirmation Step 10: The user is then prompted to select a file directory in which the touch kit controller is installed (Figure 7-7).
PAGE 169
DM Series Industrial Monitor Figure 7-7: Controller Installation Directory Step 11: The user is then prompted to select a file directory in which the program icons are saved (Figure 7-8). The default folder is “TouchKit.” If a different folder must be used, select a folder from the list shown. Once the folder is selected, click NEXT to continue.
PAGE 170
DM Series Industrial Monitor Figure 7-8: Program Icon Directory Step 12: The program then starts installing (Figure 7-9).
PAGE 171
DM Series Industrial Monitor Figure 7-9: Installing Step 13: Once the program is finished installing, the user is prompted to restart the computer now or to restart the computer later (Figure 7-10). Select when the computer should be restarted and click “FINISH” to complete the driver installation procedure.Step 0: Figure 7-10: Installation Complete 7.3 Touch Panel Driver Configuration To configure the touch panel driver options, refer to the TouchKit user manual located on the driver installation CD.
PAGE 172
DM Series Industrial Monitor THIS PAGE IS INTENTIONALLY LEFT BLANK Page 172
PAGE 173
DM Series Industrial Monitor Chapter 8 8 Gasket Replacement Page 173
PAGE 174
DM Series Industrial Monitor 8.1 Gasket Replacement A gasket used for a long time may gradually lose its ability to protect the monitor from fluids and vapors; scratches or dirt may also accumulate. It is recommended that the gasket be replaced yearly. NOTE: If the monitor is mounted vertically, first remove it and place it on a flat, level surface with the display screen facing down before changing the gasket. Step 1: Remove the old gasket from the sides of the monitor.
PAGE 175
DM Series Industrial Monitor Appendix A A Safety Precautions Page 175
PAGE 176
DM Series Industrial Monitor WARNING: The precautions outlined in this chapter should be strictly followed. Failure to follow these precautions may result in permanent damage to the DM Series. A.1 Safety Precautions Please follow the safety precautions outlined in the sections that follow: A.1.1 General Safety Precautions Please ensure the following safety precautions are adhered to at all times. Follow the electrostatic precautions outlined below whenever the DM Series is opened.
PAGE 177
DM Series Industrial Monitor A.1.2 Anti-static Precautions WARNING: Failure to take ESD precautions during the installation of the DM Series may result in permanent damage to the DM Series and severe injury to the user. Electrostatic discharge (ESD) can cause serious damage to electronic components, including the DM Series. Dry climates are especially susceptible to ESD.
PAGE 178
DM Series Industrial Monitor The interior of the DM Series does not require cleaning. Keep fluids away from the DM Series interior. Be cautious of all small removable components when vacuuming the DM Series. Turn the DM Series off before cleaning the DM Series. Never drop any objects or liquids through the openings of the DM Series. Be cautious of any possible allergic reactions to solvents or chemicals used when cleaning the DM Series.
PAGE 179
DM Series Industrial Monitor Appendix B B Certifications Page 179
PAGE 180
DM Series Industrial Monitor B.1 RoHS Compliant All models in the DM industrial monitor series comply with the Restriction of Hazardous Materials (RoHS) Directive. This means that all components used to build the industrial workstations and the workstation itself are RoHS compliant.
PAGE 181
DM Series Industrial Monitor Appendix C C smartOSD Page 181
PAGE 182
DM Series Industrial Monitor C.1 IEI smartOSD Quick Installation Guide IEI smartOSD is a proprietary On-Screen-Display (OSD) software solution from IEI that enables easy, remote monitor setting adjustments in a Windows environment. IEI smartOSD delivers excellent performance and provides more flexibility than the typical OSD hardware solutions when adjusting a monitor.
PAGE 183
DM Series Industrial Monitor Figure 8-2: smartOSD Installer Step 2: Click “Smart OSD” in Figure 8-2. Step 3: The welcome screen shown in Figure 8-3 appears. Figure 8-3: smartOSD Welcome Screen Step 4: Click Next to continue. Step 5: The Folder Select screen in Figure 8-4 appears.
PAGE 184
DM Series Industrial Monitor Figure 8-4: smartOSD Folder Select Screen Step 6: Select the installation folder in Figure 8-4 shown above. Step 7: Click Next to continue. Step 8: The screen in Figure 8-5 appears. Figure 8-5: smartOSD Confirm Installation Step 9: Confirm the installation by clicking Next in the screen above. Step 10: The program starts to install and the progress bar shown in Figure 8-6 appears.
PAGE 185
DM Series Industrial Monitor Figure 8-6: smartOSD Installation Progress Step 11: When the installation is complete the “Complete Installation” screen in Figure 8-7 appears. Figure 8-7: smartOSD Installation Complete Step 12: Click Close in the screen above. Step 13: After quick setup is complete, the IEI smartOSD wizard logo appears on the desktop as shown in the screen below. Step 14: To access the smartOSD, click the smartOSD wizard logo.
PAGE 186
DM Series Industrial Monitor C.4 Software Illustration The table below shows the smartOSD menu structure for all IEI LCD monitors. NOTE: To update the display setting status immediately, push the refresh button on every page To turn the system on, press ALT + P. Item Elements Management Save/Load File Power Management EDID EDID contains basic information about the monitor and its capabilities.
PAGE 187
DM Series Industrial Monitor Phase Clock Color Auto Color User Red Gain User Green Gain User Blue Gain Color Temperature (5000k and 4200k disabled in the DM Series) Gamma PIP PIP (disabled in the DM Series) PIP Source Input (disabled in the DM Series) PIP Size (disabled in the DM Series) System Monitor Power Control Auto Brightness (disabled in the DM Series) Main Source Input (S-Video and CVBS disabled) Volume (disabled in the DM Series) Factory Presets/OSD Lock/OSD Unlock Mute (disabled in the DM Ser
PAGE 188
DM Series Industrial Monitor C.4.
PAGE 189
DM Series Industrial Monitor C.4.
PAGE 190
DM Series Industrial Monitor C.4.
PAGE 191
DM Series Industrial Monitor C.4.
PAGE 192
DM Series Industrial Monitor C.4.
PAGE 193
DM Series Industrial Monitor C.4.6 PIP Page NOTE: The functions in the PIP page are only available in the MDM Series and AFOLUX Series monitors.
PAGE 194
DM Series Industrial Monitor C.4.
PAGE 195
DM Series Industrial Monitor C.4.
PAGE 196
DM Series Industrial Monitor C.5 smartOSD FAQ For troubleshooting, please see the steps below: C.5.1 Windows 2000 Installation Failure Installation fails under Windows 2000 and shows the following image: Figure C-9: DLL Missing Solution: Download and install service pack Windows Installer 3.
PAGE 197
DM Series Industrial Monitor C.5.2 Vista Installation Failure Installation fail under Vista while showing following image: Figure C-10: Windows Vista Error Solution: Install SmartOSD.
PAGE 198
DM Series Industrial Monitor C.5.3 Model Failure The Model Fail error message shown below appears. Figure C-12: Firmware Incompatibility Solution: SmartOSD only supports firmware version 2.0 and following versions. C.5.4 DCC Port Failure The DDC port fail error message shown below appears. Figure C-13: DCC Port Failure Solutions: Check VGA or DVI cable Check an IEI monitor is being used Make sure the version is version 2.3 for the AFOLUX/MDM series and version 1.