ECN-360A-HM65 Em b e d d e d S ys te m , IEI Te c h n o lo g y Co rp . MODEL: ECN-360A-HM65 Em b e d d e d S ys te m with In te l® Ce le ro n ® d u a l c o re 847E P ro c e s s o r, Du a l HDMI, VGA, Gb E, Two US B 3.0, Two US B 2.0, Th re e COM a n d Ro HS Co m p lia n t Us e r Ma n u a l Page i Re v. 1.
ECN-360A-HM65 Em b e d d e d S ys te m Re vis io n Date Version Changes 25 June 2013 1.
ECN-360A-HM65 Em b e d d e d S ys te m Co p yrig h t COP YRIGHT NOTICE The information in this document is subject to change without prior notice in order to improve reliability, design and function and does not represent a commitment on the part of the manufacturer. In no event will the manufacturer be liable for direct, indirect, special, incidental, or consequential damages arising out of the use or inability to use the product or documentation, even if advised of the possibility of such damages.
ECN-360A-HM65 Em b e d d e d S ys te m Ta b le o f Co n te n ts 1 INTRODUCTION.......................................................................................................... 1 1.1 OVERVIEW.................................................................................................................. 2 1.2 MODEL VARIATIONS ................................................................................................... 2 1.3 FEATURES ...........................................................
ECN-360A-HM65 Em b e d d e d S ys te m 4.1.2 Internal Peripheral Connectors ....................................................................... 26 4.1.3 External Interface Panel Connectors............................................................... 27 4.2 INTERNAL PERIPHERAL CONNECTORS ...................................................................... 27 4.2.1 Audio Connector .............................................................................................. 27 4.2.
ECN-360A-HM65 Em b e d d e d S ys te m 5 BIOS .............................................................................................................................. 55 5.1 INTRODUCTION......................................................................................................... 56 5.1.1 Starting Setup ................................................................................................... 56 5.1.2 Using Setup .....................................................................
ECN-360A-HM65 Em b e d d e d S ys te m A.2.1 Maintenance and Cleaning.............................................................................. 89 A.2.2 Cleaning Tools ................................................................................................. 90 B BIOS MENU OPTIONS ............................................................................................. 91 C ONE KEY RECOVERY ............................................................................................. 94 C.
ECN-360A-HM65 Em b e d d e d S ys te m ROHS COMPLIANT UNDER 2002/95/EC WITHOUT MERCURY .....................................
ECN-360A-HM65 Em b e d d e d S ys te m Lis t o f Fig u re s Figure 1-1: ECN-360A-HM65 ..........................................................................................................2 Figure 1-2: ECN-360A-HM65 Front Panel .....................................................................................5 Figure 1-3: ECN-360A-HM65 Rear Panel ......................................................................................6 Figure 1-4: Physical Dimensions (mm) ..............................
ECN-360A-HM65 Em b e d d e d S ys te m Figure 4-16: COM Connector Locations .....................................................................................41 Figure 4-17: Serial Port Connector Location .............................................................................42 Figure 4-18: SMBus Connector Location ...................................................................................43 Figure 4-19: SPI Flash Connector Location ..........................................................
ECN-360A-HM65 Em b e d d e d S ys te m Figure C-22: Auto Recovery Utility ...........................................................................................112 Figure C-23: Launching the Recovery Tool .............................................................................112 Figure C-24: Auto Recovery Environment for Windows ........................................................112 Figure C-25: Building the Auto Recovery Partition ............................................................
ECN-360A-HM65 Em b e d d e d S ys te m Lis t o f Ta b le s Table 1-1: Model Variations ...........................................................................................................2 Table 1-2: Technical Specifications ..............................................................................................4 Table 2-1: Package List Contents ...............................................................................................11 Table 4-1: Peripheral Interface Connectors .........
ECN-360A-HM65 Em b e d d e d S ys te m Table 4-28: Jumpers .....................................................................................................................49 Table 4-29: AT/ATX Power Mode Jumper Settings ...................................................................50 Table 4-30: Clear CMOS Jumper Settings ..................................................................................51 Table 4-31: LVDS Voltage Selection Jumper Settings ..........................................
ECN-360A-HM65 Em b e d d e d S ys te m Ch a p te r 1 1 In tro d u c tio n Page 1
ECN-360A-HM65 Em b e d d e d S ys te m 1.1 Ove rvie w Figure 1-1: ECN-360A-HM65 The ECN-360A-HM65 embedded system is a fanless system with two HDMI ports and one VGA port for dual display. It is powered by Intel® Celeron® dual core 847E 1.1GHz processor and supports two 204-pin DDR3 SDRAM SO-DIMM modules up to 8 GB (4GB memory preinstalled). The ECN-360A-HM65 supports a 2.5” SATA HDD with up to 6 Gb/s data transfer rate. Three serial ports, two USB 3.0 ports and two USB 2.
ECN-360A-HM65 Em b e d d e d S ys te m 1.4 Te c h n ic a l Sp e c ific a tio n s The ECN-360A-HM65 technical specifications are listed in Table 1-1. Ch a s s is Co lo r Black Dim e n s io n ( WxDxH) 255 x 130 x 63 S ys te m Fa n Fanless Ch a s s is Co n s tru c tio n SECC Mo th e rb o a rd Mo th e rb o a rd m o d e l NANO-HM651-847E CP U Intel® Celeron® dual core 847E 1.
ECN-360A-HM65 Em b e d d e d S ys te m Au d io 1 x Line-out Wire le s s 1 x 802.11 b/g/n ( optional) Expansions 1 x Full size ( reserved for Wi-Fi ) P CIe Min i P o we r 9~36V DC ( IDD-936260A) P o we r In p u t Power 1 : DC Jack Power 2: Terminal block P o we r Co n s u m p tio n 12V@3.01A (Intel® Celeron® single core 827E 1.
ECN-360A-HM65 Em b e d d e d S ys te m Figure 1-2: ECN-360A-HM65 Front Panel 1.6 Re a r P a n e l The rear panel of the ECN-360A-HM65 has the following features (Figure 1-3): 1 x DIO connector 1 x Line-out 2 x HDMI connectors 1 x 9 V ~ 36 V power jack 1 x Reset button 2 x RJ-45 LAN connectors 2 x RS-232 (DB-9 connector) 1 x RS-422/485 (DB-9 connector) 1 x 9 V ~ 36 V terminal block 2 x USB 3.0 connectors 2 x USB 2.
ECN-360A-HM65 Em b e d d e d S ys te m Figure 1-3: ECN-360A-HM65 Rear Panel Page 6
ECN-360A-HM65 Em b e d d e d S ys te m 1.
ECN-360A-HM65 Em b e d d e d S ys te m Ch a p te r 2 2 Un p a c kin g Page 8
ECN-360A-HM65 Em b e d d e d S ys te m 2.1 An ti-s ta tic P re c a u tio n s WARNING: Failure to take ESD precautions during installation may result in permanent damage to the ECN-360A-HM65 and severe injury to the user. Electrostatic discharge (ESD) can cause serious damage to electronic components, including the ECN-360A-HM65. Dry climates are especially susceptible to ESD.
ECN-360A-HM65 Em b e d d e d S ys te m 2.3 Un pa c kin g Ch e c klis t NOTE: If some of the components listed in the checklist below are missing, please do not proceed with the installation. Contact the IEI reseller or vendor you purchased the ECN-360A-HM65 from or contact an IEI sales representative directly. To contact an IEI sales representative, please send an email to sales@iei.com.tw.
ECN-360A-HM65 Em b e d d e d S ys te m Qu a n tity Ite m a n d P a rt Nu m b e r 1 Utility CD 1 One Key Recovery CD Im a g e Table 2-1: Package List Contents P a g e 11
ECN-360A-HM65 Em b e d d e d S ys te m Ch a p te r 3 3 In s ta lla tio n P a g e 12
ECN-360A-HM65 Em b e d d e d S ys te m 3.1 In s ta lla tio n P re c a u tio n s During installation, be aware of the precautions below: Read the user manual: The user manual provides a complete description of the ECN-360A-HM65, installation instructions and configuration options. DANGER! Disconnect Power: Power to the ECN-360A-HM65 must be disconnected during the installation process, or before any attempt is made to access the rear panel.
ECN-360A-HM65 Em b e d d e d S ys te m S te p 1: Remove six retention screws from the bottom panel (Figure 3-1). Figure 3-1: Retention Screws Removal S te p 2: Open the bottom panel and locate the HDD bracket (Figure 3-2).
ECN-360A-HM65 Em b e d d e d S ys te m S te p 3: Attach the HDD to the HDD bracket, and then slide the HDD to connect the HDD to the SATA connector. Secure the HDD with the HDD bracket by four retention screws (Figure 3-3). Figure 3-3: HDD Retention Screws S te p 4: Replace the HDD cover and secure it using six previously removed retention screws. 3.
ECN-360A-HM65 Em b e d d e d S ys te m Figure 3-4: Wi-Fi Antenna Installation 3.5 Mo u n tin g Bra c ke t In s ta lla tio n To mount the embedded system onto a wall or some other surface using the two mounting brackets, please follow the steps below. S te p 1: Turn the embedded system over. S te p 2: Align the two retention screw holes in each bracket with the corresponding retention screw holes on the sides of the bottom surface.
ECN-360A-HM65 Em b e d d e d S ys te m Align the mounting holes in the sides of the mounting brackets with the predrilled S te p 5: holes in the mounting surface. NOTE: To have the best system heat dissipation, please make sure to face the I/O panel downward (Figure 3-5) when mounting the system. Insert four retention screws, two in each bracket, to secure the system to the S te p 6: wall. S te p 0: 3.
ECN-360A-HM65 Em b e d d e d S ys te m S te p 2: Plug the audio plug into the audio jack. Plug the audio plug into the audio jack. If the plug on your speakers is different, an adapter will need to be used to plug them into the audio jack. The audio jack on the ECN-360A-HM65 is a line-out port which connects to a headphone or a speaker. Figure 3-6: Audio Connector S te p 3: Check audio clarity.
ECN-360A-HM65 Em b e d d e d S ys te m Figure 3-7: HDMI Connection S te p 3: Insert the HDMI connector. Gently insert the HDMI connector. The connector should engage with a gentle push. If the connector does not insert easily, check again that the connector is aligned correctly, and that the connector is being inserted with the right way up. 3.6.3 LAN Co n n e c tio n There are two external RJ-45 LAN connectors. The RJ-45 connector enables connection to an external network.
ECN-360A-HM65 Em b e d d e d S ys te m Figure 3-8: LAN Connection S te p 3: Insert the LAN cable RJ-45 connector. Once aligned, gently insert the LAN cable RJ-45 connector into the RJ-45 connector. S te p 0: 3.6.4 DB-9 S e ria l P o rt Co n n e c tio n There are two RS-232 DB-9 connectors and one RS-422/485 DB-9 connector of the ECN-360A-HM65 for serial device connection. Follow the steps below to connect a serial device to the DB-9 connector of the ECN-360A-HM65. S te p 1: Locate the DB-9 connector.
ECN-360A-HM65 Em b e d d e d S ys te m Figure 3-9: DB-9 Serial Port Connector S te p 3: Secure the connector. Secure the serial device connector to the external interface by tightening the two retention screws on either side of the connector. Step 0: 3.6.5 US B De vic e Co n n e c tio n NOTE: User must install the USB 3.0 driver before connecting a USB device to the system or else the system may not recognize the connected device. There are four USB 3.0 connectors and two USB 2.
ECN-360A-HM65 Em b e d d e d S ys te m Figure 3-10: USB Device Connection S te p 3: Insert the device connector. Once aligned, gently insert the USB device connector into the onboard connector. 3.6.6 VGA Mo n ito r Co n n e c tio n The ECN-360A-HM65 has a single female DB-15 connector on the external peripheral interface panel. The DB-15 connector is connected to a CRT or VGA monitor. To connect a monitor to the ECN-360A-HM65, please follow the instructions below.
ECN-360A-HM65 Em b e d d e d S ys te m Figure 3-11: VGA Connector S te p 4: Secure the connector. Secure the DB-15 VGA connector from the VGA monitor to the external interface by tightening the two retention screws on either side of the connector.
ECN-360A-HM65 Em b e d d e d S ys te m Ch a p te r 4 4 S ys te m Mo th e rb o a rd P a g e 24
ECN-360A-HM65 Em b e d d e d S ys te m 4.1 P e rip h e ra l In te rfa c e Co n n e c to rs The ECN-360A-HM651 embedded system motherboard comes with a number of peripheral interface connectors and configuration jumpers. 4.1.1 La yo u t Figure 4-1 shows the on-board peripheral interface connectors and jumpers.
ECN-360A-HM65 Em b e d d e d S ys te m 4.1.2 In te rn a l P e rip h e ra l Co n n e c to rs Table 4-1 shows a list of the internal peripheral connectors on the motherboard. Detailed descriptions of these connectors can be found below.
ECN-360A-HM65 Em b e d d e d S ys te m 4.1.3 Exte rn a l In te rfa c e P a n e l Co n n e c to rs Table 4-2 lists the rear panel connectors on the motherboard. Detailed descriptions of these connectors can be found in Section 4.3. Co n n e c to r Typ e La b e l Ethernet connectors RJ-45 LAN1, LAN2 HDMI connectors HDMI HDMI1, HDMI2 USB 2.0 ports USB port USB_CON2 USB 3.0 ports USB port USB_CON3 VGA port connector 15-pin female VGA1 Table 4-2: Rear Panel Connectors 4.
ECN-360A-HM65 Em b e d d e d S ys te m Figure 4-2: Audio Connector Location Pin Description Pin Description 1 LFRONT-R 2 3 GND 4 GND 5 LFRONT-L 6 LLINE-L 7 GND 8 GND 9 LMIC1-CONN-R 10 LMIC1-CONN-L LLINE-R Table 4-3: Audio Connector Pinouts 4.2.2 Ba tte ry Co n n e c to r CN La b e l: BAT1 CN Typ e : 2-pin wafer (1x2) CN Lo c a tio n : See Figure 4-3 CN P in o u ts : See Table 4-4 This is connected to the system battery.
ECN-360A-HM65 Em b e d d e d S ys te m Pin Description 1 Battery+ 2 Ground Table 4-4: Battery Connector Pinouts 4.2.3 Dig ita l In p u t/Ou tp u t (DIO) Co n n e c to r CN La b e l: DIO1 CN Typ e : 10-pin header (2x5) CN Lo c a tio n : See Figure 4-4 CN P in o u ts : See Table 4-5 The digital input/output connector is managed through a Super I/O chip. The DIO connector pins are user programmable.
ECN-360A-HM65 Em b e d d e d S ys te m 4.2.4 De b u g Co n n e c to r CN La b e l: DBG_P ORT1 CN Typ e : 12-pin connector (1x12) CN Lo c a tio n : See Figure 4-5 CN P in o u ts : See Table 4-6 The debug connector connects to a debug card for debugging. Figure 4-5: EC Debug Connector Location Pin Description 1 +V5S 2 +V3.
ECN-360A-HM65 Em b e d d e d S ys te m 4.2.5 Fa n Co n n e c to r (CP U) CN La b e l: CP U_FAN1 CN Typ e : 4-pin wafer (1x4) CN Lo c a tio n : See Figure 4-6 CN P in o u ts : See Table 4-7 The cooling fan connector provides a 12V, 500mA current to the cooling fan. The connector has a "rotation" pin to get rotation signals from fans and notify the system so the system BIOS can recognize the fan speed. Please note that only specified fans can issue the rotation signals.
ECN-360A-HM65 Em b e d d e d S ys te m CN Lo c a tio n : See Figure 4-7 CN P in o u ts : See Table 4-8 The cooling fan connector provides a 12V, 500mA current to the cooling fan. The connector has a "rotation" pin to get rotation signals from fans and notify the system so the system BIOS can recognize the fan speed. Please note that only specified fans can issue the rotation signals.
ECN-360A-HM65 Em b e d d e d S ys te m Reset Figure 4-8: Front Panel Connector Location FUNCTION Power Button HDD LED P IN DES CRIP TION FUNCTION P IN DES CRIP TION 1 N/A Power LED 6 PWR_LED+ 2 PWR_BTN+ 7 PWR_LED+ 3 PWR_BTN- 8 PWR_LED- 4 HDD_LED+ 9 RESET+ 5 HDD_LED- 10 RESET- Reset Table 4-9: Front Panel Connector Pinouts 4.2.
ECN-360A-HM65 Em b e d d e d S ys te m Figure 4-9: Backlight Inverter Connector Location Pin Description 1 BACKLIGHT ADJUST 2 GROUND 3 +12 V 4 GROUND 5 BACKLIGHT ENABLE Table 4-10: Backlight Inverter Connector Pinouts 4.2.
ECN-360A-HM65 Em b e d d e d S ys te m Figure 4-10: Keyboard/Mouse Connector Location Pin Description 1 VCC5_KBMS 2 MS DATA 3 MS CLK 4 KB DATA 5 KB CLK 6 GROUND Table 4-11: Keyboard/Mouse Connector Pinouts 4.2.10 LVDS LCD Co n n e c to r CN La b e l: LVDS 1 CN Typ e : 30-pin crimp (2x15) CN Lo c a tio n : See Figure 4-11 CN P in o u ts : See Table 4-12 The LVDS connector is for an LCD panel connected to the board.
ECN-360A-HM65 Em b e d d e d S ys te m Figure 4-11: LVDS Connector Location Pin Description Pin Description 1 GND 2 GND 3 A_Y0 4 A_Y0# 5 A_Y1 6 A_Y1# 7 A_Y2 8 A_Y2# 9 A_CK 10 A_CK# 11 A_Y3 12 A_Y3# 13 GND 14 GND 15 B_Y0 16 B_Y0# 17 B_Y1 18 B_Y1# 19 B_Y2 20 B_Y2# 21 B_CK 22 B_CK# 23 B_Y3 24 B_Y3# 25 GND 26 GND 27 VCC/VCC3 28 VCC/VCC3 29 VCC/VCC3 30 VCC/VCC3 Table 4-12: LVDS Connector Pinouts 4.2.
ECN-360A-HM65 Em b e d d e d S ys te m CN P in o u ts : See Table 4-4 The PCIe Mini card slot enables a PCIe Mini card expansion module to be connected to the board. Cards supported include among others wireless LAN (WLAN) cards and mSATA cards. Figure 4-12: PCIe Mini Card Slot Location Pin Description Pin Description 1 PCIE_WAKE# 2 VCC3 3 N/C 4 GND 5 N/C 6 1.
ECN-360A-HM65 Em b e d d e d S ys te m Pin Description Pin Description 37 N/C 38 USBD+ 39 N/C 40 GND 41 N/C 42 N/C 43 N/C 44 N/C 45 N/C 46 N/C 47 N/C 48 1.5V 49 N/C 50 GND 51 N/C 52 VCC3 Table 4-13: PCIe Mini Card Slot Pinouts 4.2.12 P owe r Co n n e c to r CN La b e l: P WR1 CN Typ e : 4-pin connector (2x2) CN Lo c a tio n : See Figure 4-13 CN P in o u ts : See Table 4-14 This connector accepts 12 V of power for the processor.
ECN-360A-HM65 Em b e d d e d S ys te m Pin Description Pin Description 1 GND 2 GND 3 +12 V 4 +12 V Table 4-14: CPU Power Connector Pinouts 4.2.13 S ATA 6Gb /s Co n n e c to r CN La b e l: S _ATA1, S _ATA2 CN Typ e : 7-pin SATA drive connector CN Lo c a tio n : See Figure 4-14 CN P in o u ts : See Table 4-15 The SATA connectors connect to SATA hard drives or optical drives with data transfer speeds as high as 6Gb/s.
ECN-360A-HM65 Em b e d d e d S ys te m 4.2.14 S ATA P o we r Co n n e c to rs CN La b e l: CN1, CN2 CN Typ e : 2-pin wafer CN Lo c a tio n : See Figure 4-15 CN P in o u ts : See Table 4-16 Use the SATA Power Connector to connect to SATA device power connections. Total +5V SATA power is 2A (CN1+CN2). Figure 4-15: SATA Power Connector Locations Pin Description 1 +V5S 2 GND Table 4-16: SATA Power Connector Pinouts 4.2.
ECN-360A-HM65 Em b e d d e d S ys te m Figure 4-16: COM Connector Locations Pin Description Pin Description 1 -NDCD 6 -NCTS 2 -NDSR 7 -NDTR 3 NSIN 8 -XRI 4 -NRTS 9 GND 5 NSOUT 10 GND Table 4-17: COM Connector Pinouts 4.2.16 RS -422/485 S e ria l P ort Co n n e c to r (COM3) CN La b e l: COM3 CN Typ e : 4-pin wafer (1x4) CN Lo c a tio n : See Figure 4-17 CN P in o u ts : See Table 4-18 This connector provides RS-422 or RS-485 communications.
ECN-360A-HM65 Em b e d d e d S ys te m Figure 4-17: Serial Port Connector Location Pin Description 1 RXD422- 2 RXD422+ 3 TXD422+/TXD485+ 4 TXD422-/TXD485- Table 4-18: Serial Port Connector Pinouts Use the optional RS-422/485 cable to connect to a serial device. The pinouts of the DB-9 connector are listed below. RS-422 Pinouts RS-485 Pinouts Table 4-19: DB-9 RS-422/485 Pinouts 4.2.
ECN-360A-HM65 Em b e d d e d S ys te m The SMBus Connector provides a connection to a SMBus (System Management Bus) device. Figure 4-18: SMBus Connector Location Pin Description 1 GND 2 SMB_DATA 3 SMB_CLK 4 +V5S Table 4-20: SMBus Connector Pinouts 4.2.18 S P I Fla s h Co n n e c to r CN La b e l: J S P I1 CN Typ e : 6-pin wafer (1x6) CN Lo c a tio n : See Figure 4-19 CN P in o u ts : See Table 4-21 The SPI Flash connector is used to flash the BIOS.
ECN-360A-HM65 Em b e d d e d S ys te m Figure 4-19: SPI Flash Connector Location Pin Description Pin Description 1 +V3.3M_SPI_CON 5 SPI_SI_SW 2 SPI_CS 6 GND 3 SPI_SO_SW 7 GND 4 SPI_CLK_SW 8 GND Table 4-21: SPI Flash Connector 4.3 Exte rn a l P e rip h e ra l In te rfa c e Co n n e c to r P a n e l Figure 4-20 shows the motherboard external peripheral interface connector (EPIC) panel.
ECN-360A-HM65 Em b e d d e d S ys te m 4.3.1 Eth e rn e t Co n n e c to rs CN La b e l: LAN1 a n d LAN2 CN Typ e : RJ-45 CN Lo c a tio n : See Figure 4-20 CN P in o u ts : See Table 4-22 The motherboard is equipped with two built-in RJ-45 Ethernet controllers. The controllers can connect to the LAN through two RJ-45 LAN connectors. There are two LEDs on the connector indicating the status of LAN.
ECN-360A-HM65 Em b e d d e d S ys te m 4.3.2 HDMI Co n n e c to rs CN La b e l: HDMI1, HDMI2 CN Typ e : HDMI connector CN Lo c a tio n : See Figure 4-20 CN P in o u ts : See Table 4-24 and Figure 4-22 The HDMI connector connects to a display device with HDMI interface.
ECN-360A-HM65 Em b e d d e d S ys te m CN Lo c a tio n : See Figure 4-20 CN P in o u ts : See Table 4-25 The motherboard has two external USB 2.0 ports. The ports connect to both USB 2.0 and USB 1.1 devices. Pin Description 1 VCC 2 DATA- 3 DATA+ 4 GND Table 4-25: USB 2.0 Port Pinouts 4.3.4 US B 3.0 Co n n e c to rs CN La b e l: US B_CON3 CN Typ e : USB 3.0 port CN Lo c a tio n : See Figure 4-20 CN P in o u ts : See Table 4-26 The USB 3.0 connector can be connected to a USB device.
ECN-360A-HM65 Em b e d d e d S ys te m 4.3.5 VGA Co n n e c to r CN La b e l: VGA1 CN Typ e : 15-pin Female CN Lo c a tio n : See Figure 4-20 CN P in o u ts : See Figure 4-23 and Table 4-27 The motherboard has a single 15-pin female connector for connectivity to standard display devices.
ECN-360A-HM65 Em b e d d e d S ys te m 4.4 J u m p e r S e ttin g s NOTE: A jumper is a metal bridge used to close an electrical circuit. It consists of two or three metal pins and a small metal clip (often protected by a plastic cover) that slides over the pins to connect them. To CLOSE/SHORT a jumper means connecting the pins of the jumper with the plastic clip and to OPEN a jumper means removing the plastic clip from a jumper. The jumpers on the motherboard are listed in Table 4-28.
ECN-360A-HM65 Em b e d d e d S ys te m Setting Description Short 1-2 Use ATX power (Default) Short 2-3 Use AT power Table 4-29: AT/ATX Power Mode Jumper Settings Figure 4-24: AT/ATX Power Mode Jumper Location 4.4.
ECN-360A-HM65 Em b e d d e d S ys te m After having done one of the above, save the changes and exit the CMOS Setup menu. The clear CMOS jumper settings are shown in Table 4-30. Setting Description Short 1 - 2 Keep CMOS Setup (Default) Short 2 - 3 Clear CMOS Setup Table 4-30: Clear CMOS Jumper Settings The location of the clear CMOS jumper is shown in Figure 4-25 below. Figure 4-25: Clear CMOS Jumper 4.4.
ECN-360A-HM65 Em b e d d e d S ys te m Setting Description Short 1-2 +3.3 V (Default) Short 2-3 +5.0 V Table 4-31: LVDS Voltage Selection Jumper Settings Figure 4-26: LVDS Voltage Selection Jumper Location 4.4.
ECN-360A-HM65 Em b e d d e d S ys te m Pin Description 1-2 and 7-8 1366 X 768 (24bit) 3-4 and 7-8 1440 X 900 (48bit) 1-2 and 3-4 and 7-8 1600 X 900 (48bit) 5-6 and 7-8 1680 X 1050 (48bit) 1-2 and 5-6 and 7-8 1920 X 1080 (48bit) 3-4 and 5-6 and 7-8 1920 X 1200 (48bit) Short all LVDS Disabled Table 4-32: LVDS Screen Resolution Jumper Settings Figure 4-27: LVDS Screen Resolution Jumper Locations 4.4.
ECN-360A-HM65 Em b e d d e d S ys te m Figure 4-28: TPM Setting Jumper Location 4.4.6 Fla s h De s c rip to r S e c u rity Ove rrid e J u m p e r J u m p e r La b e l: J _FLAS H1 J u m p e r Typ e : 3-pin header J u m p e r S e ttin g s : See Table 4-34 J u m p e r Lo c a tio n : See Figure 4-29 The Flash Descriptor Security Override jumper specifies whether to override the flash descriptor.
ECN-360A-HM65 Em b e d d e d S ys te m Ch a p te r 5 5 BIOS P a g e 55
ECN-360A-HM65 Em b e d d e d S ys te m 5.1 In tro d u c tio n The BIOS is programmed onto the BIOS chip. The BIOS setup program allows changes to certain system settings. This chapter outlines the options that can be changed. 5.1.1 Sta rtin g S e tu p The AMI BIOS is activated when the computer is turned on. The setup program can be activated in one of two ways. 1. Press the DELETE or F2 key as soon as the system is turned on or 2.
ECN-360A-HM65 Em b e d d e d S ys te m Ke y Fu n c tio n F4 key Save all the CMOS changes Esc key Main Menu – Quit and not save changes into CMOS Status Page Setup Menu and Option Page Setup Menu -Exit current page and return to Main Menu Table 5-1: BIOS Navigation Keys 5.1.3 Ge ttin g He lp When F1 is pressed a small help window describing the appropriate keys to use and the possible selections for the highlighted item appears. To exit the Help Window press ESC or the F1 key again. 5.1.
ECN-360A-HM65 Em b e d d e d S ys te m 5.2 Ma in The Main BIOS menu (BIOS Menu 1) appears when the BIOS Setup program is entered. The Main menu gives an overview of the basic system information. Aptio Setup Utility – Copyright (C) 2010 American Megatrends, Inc. Main Advanced Chipset Boot Security Save & Exit BIOS Information BIOS Vendor Core Version Compliency Project Version Build Date and Time American Megatrends 4.6.4.0 0.01 UEFI 2.1 B238AR10.ROM 01/15/2013 13:58:50 Set the Date.
ECN-360A-HM65 Em b e d d e d S ys te m S ys te m Tim e [xx:xx:xx] Use the System Time option to set the system time. Manually enter the hours, minutes and seconds. 5.3 Ad va n c e d Use the Advanced menu (BIOS Menu 2) to configure the CPU and peripheral devices through the following sub-menus: WARNING! Setting the wrong values in the sections below may cause the system to malfunction. Make sure that the settings made are compatible with the hardware.
ECN-360A-HM65 Em b e d d e d S ys te m Aptio Setup Utility – Copyright (C) 2010 American Megatrends, Inc. Advanced ACPI Settings ACPI Sleep State [S1 (CPU Stop Clock)] Select the highest ACPI sleep state the system will enter when the SUSPEND button is pressed. ---------------------: Select Screen ↑ ↓: Select Item Enter Select + - Change Opt. F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save & Exit ESC Exit Version 2.10.1208. Copyright (C) 2010 American Megatrends, Inc.
ECN-360A-HM65 Em b e d d e d S ys te m Aptio Setup Utility – Copyright (C) 2010 American Megatrends, Inc. Advanced Wake system with Fixed Time [Disabled] Enable or disable System wake on alarm event. When enabled, System will wake on the date: hr::min::sec specified ---------------------- : Select Screen ↑ ↓: Select Item Enter Select F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save ESC Exit Version 2.10.1208. Copyright (C) 2010 American Megatrends, Inc.
ECN-360A-HM65 Em b e d d e d S ys te m 5.3.3 CP U Co n fig u ra tio n Use the CPU Configuration menu (BIOS Menu 5) to enter the CPU Information submenu or enable Intel Virtualization Technology. Aptio Setup Utility – Copyright (C) 2010 American Megatrends, Inc. Advanced CPU Configuration Intel(R) Celeron(R) CPU 847E @ 1.
ECN-360A-HM65 Em b e d d e d S ys te m In te l Virtu a liza tio n Te c h n o lo g y [Dis a b le d ] Use the Intel Virtualization Technology option to enable or disable virtualization on the system. When combined with third party software, Intel® Virtualization technology allows several OSs to run on the same system at the same time. Disabled DEFAULT Disables Intel Virtualization Technology. Enables Intel Virtualization Technology. Enabled 5.3.
ECN-360A-HM65 Em b e d d e d S ys te m Configures SATA devices as AHCI device. AHCI 5.3.5 US B Co n fig u ra tio n Use the USB Configuration menu (BIOS Menu 7) to read USB configuration information and configure the USB settings. Aptio Setup Utility – Copyright (C) 2010 American Megatrends, Inc. Advanced USB Configuration USB Support Parameters USB Devices: 1 Keyboard, 2 Hubs --------------------: Select Screen ↑ ↓: Select Item Enter Select + - Change Opt.
ECN-360A-HM65 Em b e d d e d S ys te m 5.3.6 S u pe r IO Co n fig u ra tio n Use the Super IO Configuration menu (BIOS Menu 8) to set or change the configurations for the FDD controllers, parallel ports and serial ports. Aptio Setup Utility – Copyright (C) 2010 American Megatrends, Inc.
ECN-360A-HM65 Em b e d d e d S ys te m 5.3.6.1.1 S e ria l P o rt 1 Co n fig u ra tio n S e ria l P o rt [En a b le d ] Use the Serial Port option to enable or disable the serial port. Disabled Enabled Disable the serial port DEFAULT Enable the serial port Ch a n g e S e ttin g s [Au to ] Use the Change Settings option to change the serial port IO port address and interrupt address. Auto DEFAULT The serial port IO port address and interrupt address are automatically detected.
ECN-360A-HM65 Em b e d d e d S ys te m Ch a n g e S e ttin g s [Au to ] Use the Change Settings option to change the serial port IO port address and interrupt address. Auto DEFAULT The serial port IO port address and interrupt address are automatically detected.
ECN-360A-HM65 Em b e d d e d S ys te m IO=3E8h; Serial Port I/O port address is 3E8h and the interrupt IRQ=10 address is IRQ10 IO=3F8h; Serial Port I/O port address is 3F8h and the interrupt IRQ=10 address is IRQ10 IO=2F8h; Serial Port I/O port address is 2F8h and the interrupt IRQ=10 address is IRQ10 IO=3E8h; Serial Port I/O port address is 3E8h and the interrupt IRQ=10 address is IRQ10 IO=2E8h; Serial Port I/O port address is 2E8h and the interrupt IRQ=10 address is IRQ10
ECN-360A-HM65 Em b e d d e d S ys te m P C He a lth Sta tu s The following system parameters and values are shown. The system parameters that are monitored are: System Temperatures: o o System Temperature Fan Speed: o o CPU Temperature CPU Fan Speed System Fan Speed Voltages: o o o o o o VCC_core +5VS +12VS +1.5V VSB3V VBAT 5.3.7.1 S m a rt Fa n Mo d e Co nfig u ra tio n Use the Smart Fan Mode Configuration submenu (BIOS Menu 11) to configure fan temperature and speed settings.
ECN-360A-HM65 Em b e d d e d S ys te m CP U Fa n S m a rt Fa n Co n tro l [Au to Du ty-Cyc le Mo d e ] Use the CPU Smart Fan control option to configure the CPU Smart Fan. Manual The fan spins at the speed set in Manual by Duty Duty-Cycle settings Mode Auto DEFAULT The fan adjusts its speed using Auto by Duty-Cycle settings Duty-Cycle Mode Te m p e ra tu re n Use the + or – key to change the fan Temperature n value. Enter a decimal number between 0 and 100.
ECN-360A-HM65 Em b e d d e d S ys te m Aptio Setup Utility – Copyright (C) 2010 American Megatrends, Inc. Advanced COM1 Console Redirection > Console Redirection Settings [Disabled] COM2 Console Redirection > Console Redirection Settings [Disabled] Console Redirection Enable or Disable --------------------: Select Screen [Disabled] ↑ ↓: Select Item Enter Select +/-: Change Opt. F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save & Exit ESC Exit Version 2.10.1208.
ECN-360A-HM65 Em b e d d e d S ys te m Aptio Setup Utility – Copyright (C) 2010 American Megatrends, Inc. Advanced COM1 Console Redirection Settings Terminal Type Bits per second Data Bits Parity Stop Bits [ANSI] [115200] [8] [None] [1] Emulation: ANSI: Extended ASCII char set. VT100: ASCII char set. VT100+: Extends VT100 to support color, function keys, etc. VT-UTF8: Uses UTF8 encoding to map Unicode chars onto 1 or more bytes.
ECN-360A-HM65 Em b e d d e d S ys te m 57600 115200 The transmission speed is 57600 DEFAULT The transmission speed is 115200 Da ta Bits [8] Use the Data Bits option to specify the number of data bits. 7 8 Sets the data bits at 7. DEFAULT Sets the data bits at 8. P a rity [No n e ] Use the Parity option to specify the parity bit that can be sent with the data bits for detecting the transmission errors. None Even DEFAULT No parity bit is sent with the data bits.
ECN-360A-HM65 Em b e d d e d S ys te m 5.4 iEi Fe a tu re Use the iEi Feature menu (BIOS Menu 14) to configure the auto recovery function. Aptio Setup Utility – Copyright (C) 2010 American Megatrends, Inc. Advanced iEi Feature Auto Recovery Function [Disabled] Auto Recovery Function Reboot and recover system automatically within 10 min, when OS crashes.
ECN-360A-HM65 Em b e d d e d S ys te m WARNING! Setting the wrong values for the Chipset BIOS selections in the Chipset BIOS menu may cause the system to malfunction. Aptio Setup Utility – Copyright (C) 2010 American Megatrends, Inc. Main Advanced Chipset Boot Security Save & Exit > NorthBridge Configuration > SouthBridge Configuration North Bridge Parameters --------------------: Select Screen ↑ ↓: Select Item Enter Select + - Change Opt.
ECN-360A-HM65 Em b e d d e d S ys te m 5.5.1 No rth Brid g e Co n fig u ra tio n Use the NorthBridge Configuration menu (BIOS Menu 16) to configure the Northbridge chipset. Aptio Setup Utility – Copyright (C) 2010 American Megatrends, Inc. Chipset NorthBridge Configuration Check to enable VT-d function on MCH.
ECN-360A-HM65 Em b e d d e d S ys te m 5.5.1.1 Gra p h ic s Co n fig u ra tio n Use the Graphics Configuration menu to configure the video device connected to the system. Aptio Setup Utility – Copyright (C) 2010 American Megatrends, Inc. Chipset Graphics Configuration DVMT Pre-Allocated DVMT Total Gfx Mem [256M] [MAX] Boot Display Device LCD Panel Type PID Current Jumper Setting Backlight Control [Auto] [By Hardware] 1024x768 24BIT [Normal] Select DVMT 5.
ECN-360A-HM65 Em b e d d e d S ys te m DVMT To ta l Gfx Me m [MAX] Use the DVMT Total Gfx Mem option to specify the total amount of memory that can be allocated as graphics memory. Configuration options are listed below. 128M 256M MAX DEFAULT Bo o t Dis p la y De vic e Use the Boot Display Device option to select the display device used by the system when it boots. Configuration options are listed below.
ECN-360A-HM65 Em b e d d e d S ys te m 1920x1080 (48bit) 1920x1200 (48bit) 2048x1536 (48bit) Ba c klig h t Co n tro l [No rm a l] Use the Backlight Control option to select backlight control mode. Normal Inverted DEFAULT Brightest at low voltage level. Brightest at high voltage level. 5.5.2 S o u th b rid g e Co n fig u ra tio n Use the Southbridge Configuration menu (BIOS Menu 18) to configure the Southbridge chipset.
ECN-360A-HM65 Em b e d d e d S ys te m Power On Last State The system turns on DEFAULT The system returns to its previous state. If it was on, it turns itself on. If it was off, it remains off. Aza lia [En a b le d ] Use the Azalia option to enable or disable the High Definition Audio controller.
ECN-360A-HM65 Em b e d d e d S ys te m 5.6 Bo o t Use the Boot menu (BIOS Menu 19) to configure system boot options. Aptio Setup Utility – Copyright (C) 2010 American Megatrends, Inc.
ECN-360A-HM65 Em b e d d e d S ys te m Qu ie t Bo o t [En a b le d ] Use the Quiet Boot BIOS option to select the screen display when the system boots. Disabled Enabled Normal POST messages displayed DEFAULT OEM Logo displayed instead of POST messages La u n c h P XE Op ROM [Dis a b le d ] Use the Launch PXE OpROM option to enable or disable boot option for legacy network devices.
ECN-360A-HM65 Em b e d d e d S ys te m 5.7 S e c u rity Use the Security menu (BIOS Menu 20) to set system and user passwords. Aptio Setup Utility – Copyright (C) 2010 American Megatrends, Inc. Main Advanced Chipset Boot Security Save & Exit Password Description Set Setup Administrator Password If ONLY the Administrator’s password is set, then this only limits access to Setup and is only asked for when entering Setup.
ECN-360A-HM65 Em b e d d e d S ys te m 5.8 Exit Use the Exit menu (BIOS Menu 21) to load default BIOS values, optimal failsafe values and to save configuration changes. Aptio Setup Utility – Copyright (C) 2010 American Megatrends, Inc. Main Advanced Chipset Boot Security Save & Exit Save Changes and Reset Discard Changes and Reset Exit the system after saving the changes.
ECN-360A-HM65 Em b e d d e d S ys te m S a ve a s Us e r De fa u lts Use the Save as User Defaults option to save the changes done so far as user defaults. Re s to re Us e r De fa u lts Use the Restore User Defaults option to restore the user defaults to all the setup options.
ECN-360A-HM65 Em b e d d e d S ys te m Appendix A A S a fe ty P re c a u tio n s P a g e 86
ECN-360A-HM65 Em b e d d e d S ys te m WARNING: The precautions outlined in this chapter should be strictly followed. Failure to follow these precautions may result in permanent damage to the ECN-360A-HM65. A.1 S a fe ty P re c a u tio n s Please follow the safety precautions outlined in the sections that follow: A.1.1 Ge n e ra l S a fe ty P re c a u tio n s Please ensure the following safety precautions are adhered to at all times.
ECN-360A-HM65 Em b e d d e d S ys te m A.1.2 An ti-s ta tic P re c a u tio n s WARNING: Failure to take ESD precautions during the installation of the ECN-360A-HM65 may result in permanent damage to the ECN-360A-HM65 and severe injury to the user. Electrostatic discharge (ESD) can cause serious damage to electronic components, including the ECN-360A-HM65. Dry climates are especially susceptible to ESD.
ECN-360A-HM65 Em b e d d e d S ys te m A.1.3 P ro d u c t Dis p o s a l CAUTION: Risk of explosion if battery is replaced by and incorrect type. Only certified engineers should replace the on-board battery. Dispose of used batteries according to instructions and local regulations. Outside the European Union - If you wish to dispose of used electrical and electronic products outside the European Union, please contact your local authority so as to comply with the correct disposal method.
ECN-360A-HM65 Em b e d d e d S ys te m The interior of the ECN-360A-HM65X does not require cleaning. Keep fluids away from the ECN-360A-HM65 interior. Be cautious of all small removable components when vacuuming the ECN-360A-HM65. Turn the ECN-360A-HM65 off before cleaning the ECN-360A-HM65. Never drop any objects or liquids through the openings of the ECN-360A-HM65. Be cautious of any possible allergic reactions to solvents or chemicals used when cleaning the ECN-360A-HM65.
ECN-360A-HM65 Em b e d d e d S ys te m Appendix B B BIOS Me n u Op tio n s P a g e 91
ECN-360A-HM65 Em b e d d e d S ys te m System Overview .................................................................................................................58 System Date [xx/xx/xx] ........................................................................................................58 System Time [xx:xx:xx] .......................................................................................................59 ACPI Sleep State [S1 (CPU Stop Clock)] ...........................
ECN-360A-HM65 Em b e d d e d S ys te m Restore on AC Power Loss [Last State] ............................................................................79 Azalia [Enabled] ...................................................................................................................80 Azalia internal HDMI codec [Enabled] ...............................................................................80 Bootup NumLock State [On] .............................................................
ECN-360A-HM65 Em b e d d e d S ys te m Ap p e n d ix C C On e Ke y Re c o ve ry P a g e 94
ECN-360A-HM65 Em b e d d e d S ys te m C.1 On e Ke y Re c o ve ry In tro d u c tio n The IEI one key recovery is an easy-to-use front end for the Norton Ghost system backup and recovery tool. This tool provides quick and easy shortcuts for creating a backup and reverting to that backup or reverting to the factory default settings.
ECN-360A-HM65 Em b e d d e d S ys te m After completing the five initial setup procedures as described above, users can access the recovery tool by pressing while booting up the system. The detailed information of each function is described in Section C.5. NOTE: The initial setup procedures for Linux system are described in Section C.3. C.1.1 S ys te m Re q u ire m e n t NOTE: The recovery CD can only be used with IEI products.
ECN-360A-HM65 Em b e d d e d S ys te m partitions. Please take the following table as a reference when calculating the size of the partition. OS OS Image after Ghost Compression Ratio Windows® 7 7 GB 5 GB 70% Windows® XPE 776 MB 560 MB 70% Windows® CE 6.0 36 MB 28 MB 77% NOTE: Specialized tools are required to change the partition size if the operating system is already installed. C.1.
ECN-360A-HM65 Em b e d d e d S ys te m o o o o o o o Ubuntu 8.10 (Intrepid) Ubuntu 7.10 (Gutsy) Ubuntu 6.10 (Edgy) Debian 5.0 (Lenny) Debian 4.0 (Etch) SuSe 11.2 SuSe 10.3 NOTE: Installing unsupported OS versions may cause the recovery tool to fail. C.2 S e tu p P ro c e d u re fo r Win d ows Prior to using the recovery tool to backup or restore, a few setup procedures are required. S te p 1: Hardware and BIOS setup (see Section C.2.1) S te p 2: Create partitions (see Section C.2.
ECN-360A-HM65 Em b e d d e d S ys te m C.2.1 Ha rdwa re a n d BIOS S e tu p S te p 1: Make sure the system is powered off and unplugged. S te p 2: Install a hard drive or SSD in the system. An unformatted and unpartitioned disk is recommended. S te p 3: Connect an optical disk drive to the system and insert the recovery CD. S te p 4: Turn on the system. S te p 5: Press the key as soon as the system is turned on to enter the BIOS.
ECN-360A-HM65 Em b e d d e d S ys te m Figure C-2: Launching the Recovery Tool S te p 3: The recovery tool setup menu is shown as below. Figure C-3: Recovery Tool Setup Menu S te p 4: P a g e 100 Press <6> then .
ECN-360A-HM65 Em b e d d e d S ys te m Figure C-4: Command Prompt S te p 5: The command prompt window appears. Type the following commands (marked in red) to create two partitions. One is for the OS installation; the other is for saving recovery files and images which will be an invisible partition.
ECN-360A-HM65 Em b e d d e d S ys te m Figure C-5: Partition Creation Commands P a g e 102
ECN-360A-HM65 Em b e d d e d S ys te m NOTE: Use the following commands to check if the partitions were created successfully. S te p 6: Press any key to exit the recovery tool and automatically reboot the system. Please continue to the following procedure: Build the Recovery Partition.Step0: C.2.3 In s ta ll Op e ra tin g S ys te m , Drive rs a n d Ap p lic a tio n s Install the operating system onto the unlabelled partition.
ECN-360A-HM65 Em b e d d e d S ys te m C.2.4 Bu ild in g th e Re c o ve ry P a rtitio n S te p 1: Put the recover CD in the optical drive. S te p 2: Start the system. S te p 3: Boot the system from the recovery CD. When prompted, press any key to boot from the recovery CD. It will take a while to launch the recovery tool. Please be patient! Figure C-6: Launching the Recovery Tool S te p 4: When the recovery tool setup menu appears, press <2> then .
ECN-360A-HM65 Em b e d d e d S ys te m S te p 5: The Symantec Ghost window appears and starts configuring the system to build a recovery partition. In this process the partition created for recovery files in Section C.2.2 is hidden and the recovery tool is saved in this partition. Figure C-8: Building the Recovery Partition S te p 6: After completing the system configuration, press any key in the following window to reboot the system.
ECN-360A-HM65 Em b e d d e d S ys te m C.2.5 Cre a te Fa c to ry De fa u lt Im a g e NOTE: Before creating the factory default image, please configure the system to a factory default environment, including driver and application installations. To create a factory default image, please follow the steps below. S te p 1: Turn on the system. When the following screen displays (Figure C-10), press the key to access the recovery tool.
ECN-360A-HM65 Em b e d d e d S ys te m Figure C-12: About Symantec Ghost Window S te p 4: Use mouse to navigate to the option shown below (Figure C-13). Figure C-13: Symantec Ghost Path S te p 5: Select the local source drive (Drive 1) as shown in Figure C-14. Then click OK.
ECN-360A-HM65 Em b e d d e d S ys te m Figure C-14: Select a Local Source Drive S te p 6: Select a source partition (Part 1) from basic drive as shown in Figure C-15. Then click OK. Figure C-15: Select a Source Partition from Basic Drive S te p 7: Select 1.2: [Recovery] NTFS drive and enter a file name called iei (Figure C-16). Click Save. The factory default image will then be saved in the selected recovery drive and named IEI.GHO. WARNING: The file name of the factory default image must be iei.GHO.
ECN-360A-HM65 Em b e d d e d S ys te m Figure C-16: File Name to Copy Image to S te p 8: When the Compress Image screen in Figure C-17 prompts, click High to make the image file smaller.
ECN-360A-HM65 Em b e d d e d S ys te m S te p 9: The Proceed with partition image creation window appears, click Yes to continue. Figure C-18: Image Creation Confirmation S te p 10: The Symantec Ghost starts to create the factory default image (Figure C-19). Figure C-19: Image Creation Complete S te p 11: When the image creation completes, a screen prompts as shown in Figure C-20. Click Continue and close the Ghost window to exit the program.
ECN-360A-HM65 Em b e d d e d S ys te m S te p 12: The recovery tool main menu window is shown as below. Press any key to reboot the system. Step0: Figure C-21: Press Any Key to Continue C.3 Au to Re c o ve ry S e tu p P ro c e d u re The auto recovery function allows a system to automatically restore from the factory default image after encountering a Blue Screen of Death (BSoD) or a hang for around 10 minutes. To use the auto recovery function, follow the steps described in the following sections.
ECN-360A-HM65 Em b e d d e d S ys te m Figure C-22: Auto Recovery Utility S te p 3: Reboot the system from the recovery CD. When prompted, press any key to boot from the recovery CD. It will take a while to launch the recovery tool. Please be patient! Figure C-23: Launching the Recovery Tool S te p 4: When the recovery tool setup menu appears, press <4> then .
ECN-360A-HM65 Em b e d d e d S ys te m S te p 5: The Symantec Ghost window appears and starts configuring the system to build an auto recovery partition. In this process the partition created for recovery files in Section C.2.2 is hidden and the auto recovery tool is saved in this partition. Figure C-25: Building the Auto Recovery Partition S te p 6: After completing the system configuration, the following message prompts to confirm whether to create a factory default image.
ECN-360A-HM65 Em b e d d e d S ys te m S te p 7: The Symantec Ghost starts to create the factory default image (Figure C-27). Figure C-27: Image Creation Complete S te p 8: After completing the system configuration, press any key in the following window to restart the system. Figure C-28: Press any key to continue S te p 9: Eject the One Key Recovery CD and restart the system. S te p 10: Press the key as soon as the system is turned on to enter the BIOS.
ECN-360A-HM65 Em b e d d e d S ys te m Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc. Advanced iEi Feature Auto Recovery Function [Disabled] Auto Recovery Function Reboot and recover system automatically within 10 min, when OS crashes. Please install Auto Recovery API service before enabling this function --------------------: Select Screen ↑ ↓: Select Item Enter Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit Version 2.
ECN-360A-HM65 Em b e d d e d S ys te m S te p 1: Hardware and BIOS setup. Refer to Section C.2.1. S te p 2: Install Linux operating system. Make sure to install GRUB (v0.97 or earlier) MBR type and Ext3 partition type. Leave enough space on the hard drive to create the recover partition later. NOTE: If the Linux OS is not installed with GRUB (v0.97 or earlier) and Ext3, the Symantec Ghost may not function properly.
ECN-360A-HM65 Em b e d d e d S ys te m DISKPART>sel disk 0 DISKPART>create part pri size= ___ DISKPART>assign letter=N DISKPART>exit system32>format N: /fs:ntfs /q /v:Recovery /y system32>exit S te p 4: Build the recovery partition. Press any key to boot from the recovery CD. It will take a while to launch the recovery tool. Please be patient. When the recovery tool setup menu appears, type <3> and press (Figure C-30).
ECN-360A-HM65 Em b e d d e d S ys te m Figure C-31: Access menu.lst in Linux (Text Mode) S te p 6: Modify the menu.lst as shown below. S te p 7: The recovery tool menu appears. (Figure C-32) Figure C-32: Recovery Tool Menu S te p 8: Create a factory default image. Follow Step 2 ~ Step 12 described in Section C.2.5 to create a factory default image.
ECN-360A-HM65 Em b e d d e d S ys te m C.5 Re c o ve ry To o l Fu n c tio n s After completing the initial setup procedures as described above, users can access the recovery tool by pressing while booting up the system. However, if the setup procedure in Section C.3 has been completed and the auto recovery function is enabled, the system will automatically restore from the factory default image without pressing the F3 key. The recovery tool main menu is shown below.
ECN-360A-HM65 Em b e d d e d S ys te m WARNING: All data in the system will be deleted during the system recovery. Please backup the system files before restoring the system (either Factory Restore or Restore Backup). C.5.1 Fa c to ry Re s to re To restore the factory default image, please follow the steps below. S te p 1: Type <1> and press in the main menu. S te p 2: The Symantec Ghost window appears and starts to restore the factory default. A factory default image called iei.
ECN-360A-HM65 Em b e d d e d S ys te m Figure C-35: Recovery Complete Window C.5.2 Ba c ku p S ys te m To backup the system, please follow the steps below. S te p 1: Type <2> and press in the main menu. S te p 2: The Symantec Ghost window appears and starts to backup the system. A backup image called iei_user.GHO is created in the hidden Recovery partition. Figure C-36: Backup System S te p 3: The screen shown in Figure C-37 appears when system backup is complete.
ECN-360A-HM65 Em b e d d e d S ys te m Figure C-37: System Backup Complete Window C.5.3 Re s to re Yo u r La s t Ba c ku p To restore the last system backup, please follow the steps below. S te p 1: Type <3> and press in the main menu. S te p 2: The Symantec Ghost window appears and starts to restore the last backup image (iei_user.GHO). Figure C-38: Restore Backup S te p 3: The screen shown in Figure C-39 appears when backup recovery is complete. Press any key to reboot the system.
ECN-360A-HM65 Em b e d d e d S ys te m Figure C-39: Restore System Backup Complete Window C.5.4 Ma n u a l To restore the last system backup, please follow the steps below. S te p 1: Type <4> and press in the main menu. S te p 2: The Symantec Ghost window appears. Use the Ghost program to backup or recover the system manually. Figure C-40: Symantec Ghost Window S te p 3: When backup or recovery is completed, press any key to reboot the system.
ECN-360A-HM65 Em b e d d e d S ys te m C.6 Re s to re S ys te m s fro m a Lin u x S e rve r thro u g h LAN The One Key Recovery allows a client system to automatically restore to a factory default image saved in a Linux system (the server) through LAN connectivity after encountering a Blue Screen of Death (BSoD) or a hang for around 10 minutes. To be able to use this function, the client system and the Linux system MUST reside in the same domain.
ECN-360A-HM65 Em b e d d e d S ys te m C.6.1 Co n fig u re DHCP S e rve r S e ttin g s S te p 1: Install the DHCP #yum install dhcp (CentOS, commands marked in red) #apt-get install dhcp3-server (Debian, commands marked in blue) S te p 2: Confirm the operating system default settings: dhcpd.conf. CentOS Use the following command to show the DHCP server sample location: #vi /etc/dhcpd.
ECN-360A-HM65 Em b e d d e d S ys te m filename “pxelinux.0”; C.6.2 Co n fig u re TFTP S e ttin g s S te p 1: Install the tftp, httpd and syslinux. #yum install tftp-server httpd syslinux (CentOS) #apt-get install tftpd-hpa xinetd syslinux (Debian) S te p 2: Enable the TFTP server by editing the “/etc/xinetd.d/tftp” file and make it use the remap file. The “-vvv” is optional but it could definitely help on getting more information while running the remap file. For example: CentOS #vi /etc/xinetd.
ECN-360A-HM65 Em b e d d e d S ys te m Debian Replace the TFTP settings from “inetd” to “xinetd” and annotate the “inetd” by adding “#”. #vi /etc/inetd.conf Modify: #tftp dgram udp wait root /usr/sbin....... (as shown below) #vi /etc/xinetd.d/tftp C.6.3 Co n fig u re On e Ke y Re c o ve ry S e rve r S e ttin g s S te p 1: Copy the Utility/RECOVERYR10.TAR.BZ2 package from the One Key Recovery CD to the system (server side). S te p 2: Extract the recovery package to /. #cp RecoveryR10.tar.
ECN-360A-HM65 Em b e d d e d S ys te m C.6.4 Sta rt th e DHCP, TFTP a n d HTTP Start the DHCP, TFTP and HTTP. For example: CentOS #service xinetd restart #service httpd restart #service dhcpd restart Debian #/etc/init.d/xinetd reload #/etc/init.d/xinetd restart #/etc/init.d/dhcp3-server restart C.6.5 Cre a te S ha re d Dire c to ry S te p 1: Install the samba. #yum install samba S te p 2: Create a shared directory for the factory default image. #mkdir /share #cd /share #mkdir /image #cp iei.
ECN-360A-HM65 Em b e d d e d S ys te m Modify: [image] comment = One Key Recovery path = /share/image browseable = yes writable = yes public = yes create mask = 0644 directory mask = 0755 S te p 4: Edit “/etc/samba/smb.conf” for your environment. For example: S te p 5: Modify the hostname #vi /etc/hostname Modify: RecoveryServer C.6.6 S e tu p a Clie n t S ys te m fo r Au to Re c o ve ry S te p 1: Configure the following BIOS options of the client system.
ECN-360A-HM65 Em b e d d e d S ys te m S te p 2: Continue to configure the Boot Option Priorities BIOS option of the client system: Boot Option #1 remain the default setting to boot from the original OS. Boot Option #2 select the boot from LAN option. S te p 3: Save changes and exit BIOS menu. Exit Save Changes and Exit S te p 4: Install the auto recovery utility into the system by double clicking the Utility/AUTORECOVERY-SETUP.exe in the One Key Recovery CD.
ECN-360A-HM65 Em b e d d e d S ys te m NOTE: A firewall or a SELinux is not in use in the whole setup process. If there is a firewall or a SELinux protecting the system, modify the configuration information to accommodate them.
ECN-360A-HM65 Em b e d d e d S ys te m C.7 Oth e r In fo rm a tio n C.7.1 Us in g AHCI Mo d e o r ALi M5283 / VIA VT6421A Co n tro lle r When the system uses AHCI mode or some specific SATA controllers such as ALi M5283 or VIA VT6421A, the SATA RAID/AHCI driver must be installed before using one key recovery. Please follow the steps below to install the SATA RAID/AHCI driver. S te p 1: Copy the SATA RAID/AHCI driver to a floppy disk and insert the floppy disk into a USB floppy disk drive.
ECN-360A-HM65 Em b e d d e d S ys te m S te p 5: When the following window appears, press to select “Specify Additional Device”. S te p 6: In the following window, select a SATA controller mode used in the system. Then press . The user can now start using the SATA HDD.
ECN-360A-HM65 Em b e d d e d S ys te m After pressing , the system will get into the recovery tool setup menu. S te p 7: Continue to follow the setup procedure from Step 4 in Section C.2.2 Create Partitions to finish the whole setup process.Step0: C.7.2 S ys te m Me m o ry Re q u ire m e n t To be able to access the recovery tool by pressing while booting up the system, please make sure to have enough system memory. The minimum memory requirement is listed below.
ECN-360A-HM65 Em b e d d e d S ys te m Appendix D D Wa tc h d o g Tim e r P a g e 135
ECN-360A-HM65 Em b e d d e d S ys te m NOTE: The following discussion applies to DOS environment. IEI support is contacted or the IEI website visited for specific drivers for more sophisticated operating systems, e.g., Windows and Linux. The Watchdog Timer is provided to ensure that standalone systems can always recover from catastrophic conditions that cause the CPU to crash. This condition may have occurred by external EMI or a software bug.
ECN-360A-HM65 Em b e d d e d S ys te m NOTE: When exiting a program it is necessary to disable the Watchdog Timer, otherwise the system resets.
ECN-360A-HM65 Em b e d d e d S ys te m Ap p e n d ix E E Ha za rd o u s Ma te ria ls Dis c lo s u re P a g e 138
ECN-360A-HM65 Em b e d d e d S ys te m E.1 Ha za rd o u s Ma te ria ls Dis c lo s u re Ta ble for IP B P ro d u c ts Ce rtifie d a s Ro HS Co m p lia n t Un d e r 2002/95/EC With o u t Me rc u ry The details provided in this appendix are to ensure that the product is compliant with the Peoples Republic of China (China) RoHS standards. The table below acknowledges the presences of small quantities of certain materials in the product, and is applicable to China RoHS only.
ECN-360A-HM65 Em b e d d e d S ys te m P a rt Na m e To xic o r Ha za rd o u s S u b s ta n c e s a n d Ele m e n ts Le a d Me rc u ry Ca d m iu m He xa va le n t P o lyb ro m in a te d P o lyb ro m in a te d (P b ) (Hg ) (Cd ) Ch ro m iu m Bip h e n yls Dip h e n yl (CR(VI)) (P BB) Eth e rs (P BDE) Ho u s in g X O O O O X Dis p la y X O O O O X P rin te d Circ u it X O O O O X X O O O O O X O O O O X Fa n As s e m b ly X O O O O X P o we r S u p p ly
ECN-360A-HM65 Em b e d d e d S ys te m 此附件旨在确保本产品符合中国 RoHS 标准。以下表格标示此产品中某有毒物质的含量符 合中国 RoHS 标准规定的限量要求。 本产品上会附有”环境友好使用期限”的标签,此期限是估算这些物质”不会有泄漏或突变”的 年限。本 产品可能包含有较短的环境友好使用期限的可替换元件,像是电池或灯管,这些元 件将会单独标示出来。 部件名称 有毒有害物质或元素 铅 汞 镉 六价铬 多溴联苯 多溴二苯 (P b ) (Hg ) (Cd ) (CR(VI)) (P BB) 醚 (P BDE) 壳体 X O O O O X 显示 X O O O O X 印刷电路板 X O O O O X 金属螺帽 X O O O O O 电缆组装 X O O O O X 风扇组装 X O O O O X 电力供应组装 X O O O O X 电池 O O O O O O O: 表示该有毒有害物质在该部件所有物质材料中的含量均在 SJ