ICE-945GSE COM Express Type 2 Module MODEL: ICE-945GSE COM Express Module (Type 2) Intel® ATOM CPU RoHS Compliant User Manual Page i Rev. 1.
ICE-945GSE COM Express Type 2 Module Revision Date Version Changes 24 November, 2011 1.11 Added a thermal management warning on p.41 Added a heat sink in the package list. Page ii 13 July, 2011 1.10 Updated for R11 version 11 March, 2009 1.01 Updated product name 08 December, 2008 1.
ICE-945GSE COM Express Type 2 Module Copyright COPYRIGHT NOTICE The information in this document is subject to change without prior notice in order to improve reliability, design and function and does not represent a commitment on the part of the manufacturer. In no event will the manufacturer be liable for direct, indirect, special, incidental, or consequential damages arising out of the use or inability to use the product or documentation, even if advised of the possibility of such damages.
ICE-945GSE COM Express Type 2 Module Packing List NOTE: If any of the components listed in the checklist below are missing, please do not proceed with the installation. Contact the IEI reseller or vendor you purchased the ICE-945GSE from or contact an IEI sales representative directly. To contact an IEI sales representative, please send an email to sales@iei.com.tw The items listed below should all be included in the ICE-945GSE package.
ICE-945GSE COM Express Type 2 Module Table of Contents 1 INTRODUCTION.......................................................................................................... 1 1.1 OVERVIEW.................................................................................................................. 2 1.2 APPLICATIONS ............................................................................................................ 2 1.3 BENEFITS ...............................................................
ICE-945GSE COM Express Type 2 Module 2.5.8 SATA Controller ............................................................................................... 16 2.5.9 SPI Bus............................................................................................................. 17 2.5.10 USB Controller .............................................................................................. 17 2.6 ENVIRONMENTAL AND POWER SPECIFICATIONS ....................................................... 17 2.6.
ICE-945GSE COM Express Type 2 Module 6 BIOS SETUP ................................................................................................................ 44 6.1 INTRODUCTION......................................................................................................... 45 6.1.1 Starting Setup................................................................................................... 45 6.1.2 Using Setup ................................................................................
ICE-945GSE COM Express Type 2 Module 7.3 CHIPSET DRIVER INSTALLATION ............................................................................... 91 7.4 VGA DRIVER INSTALLATION .................................................................................... 94 7.5 LAN DRIVER INSTALLATION .................................................................................... 99 7.6 AUDIO DRIVER INSTALLATION ............................................................................... 101 7.6.
ICE-945GSE COM Express Type 2 Module List of Figures Figure 1–1: ICE-945GSE.................................................................................................................2 Figure 1-2: ICE-945GSE Overview (Front Side) ...........................................................................4 Figure 1-3: ICE-945GSE Overview (Reverse Side) ......................................................................4 Figure 2-1: Main Dimensions (mm)................................................
ICE-945GSE COM Express Type 2 Module Figure 7-16: LAN Driver Welcome Screen .................................................................................99 Figure 7-17: LAN Driver Welcome Screen .............................................................................. 100 Figure 7-18: LAN Driver Installation ........................................................................................ 100 Figure 7-19: LAN Driver Installation Complete.......................................................
ICE-945GSE COM Express Type 2 Module List of Tables Table 1-1: Technical Specifications..............................................................................................6 Table 2-1: Supported HDD Specifications..................................................................................15 Table 2-2: Power Consumption...................................................................................................19 Table 3-1: Package List Contents .........................................
ICE-945GSE COM Express Type 2 Module BIOS Menus BIOS Menu 1: Main .......................................................................................................................47 BIOS Menu 2: Advanced ..............................................................................................................49 BIOS Menu 3: CPU Configuration ...............................................................................................49 BIOS Menu 4: IDE Configuration.............................
ICE-945GSE COM Express Type 2 Module Chapter 1 1 Introduction Page 1
ICE-945GSE COM Express Type 2 Module 1.1 Overview Figure 1–1: ICE-945GSE The ICE-945GSE COM Express module provides the main processing chips and is connected to a compatible COM Express carrier board. The ICE-945GSE is equipped with an 1.6 GHz Intel® ATOM™ N270 CPU, Intel® 945GSE Northbridge and Intel® ICH7M Southbridge and provides multiple modern serial I/O options, while offering limited support for legacy I/Os.
ICE-945GSE COM Express Type 2 Module 1.3 Benefits Some of the ICE-945GSE embedded platform benefits include: Low power, high performance Easy integration into customized baseboards Easy upgrading Easy maintenance Easy design compatibility Low cost product development 1.4 Features Some of the ICE-945GSE features are listed below: Complies with COM Express form factor Complies with RoHS Embedded 1.
ICE-945GSE COM Express Type 2 Module Figure 1-2: ICE-945GSE Overview (Front Side) Figure 1-3: ICE-945GSE Overview (Reverse Side) 1.5.
ICE-945GSE COM Express Type 2 Module 1.5.2 IO Interface Support The ICE-945GSE embedded module supports the following IO interfaces on the baseboard: 8 x USB 2.0 1 x SDVO 4 x PCIe x1 4 x PCI 2 x SATA 1 x IDE 1 x GbE HD Audio (through HD audio chip on the baseboard, connected to HD audio interface on the ICE-945GSE) Legacy ports (COM, LPT, BIOS, PS/2) through super I/O on the baseboard connected to the LPC interface on the ICE-945GSE. 1.5.
ICE-945GSE COM Express Type 2 Module Specification Value I/O Interfaces 8 x USB 2 .0 2 x SATA 1 x IDE 1 x GbE Expansion 4 x PCIe x1 4 x PCI (32-bit, 33 MHz) BIOS AMI Power Support AT/ATX power supported Power Consumption 12 V @ 0.95 A Watchdog Timer Software programmable supports 1~255 sec.
ICE-945GSE COM Express Type 2 Module Chapter 2 2 Detailed Specifications Page 7
ICE-945GSE COM Express Type 2 Module 2.1 Dimensions The dimensions of the board are listed below: Length: 125 mm Width: 95 mm 2.1.1 Main Dimensions The figure below shows the dimensions from the top view.
ICE-945GSE COM Express Type 2 Module 2.1.2 Side Dimensions The figure below shows the dimensions as viewed from the side.
ICE-945GSE COM Express Type 2 Module 2.2 Data Flow Figure 2-3 shows the data flow between the two on-board chipsets and other components installed on the motherboard and described in the following sections of this chapter.
ICE-945GSE COM Express Type 2 Module 2.3 Embedded 1.6 GHz Intel® ATOM™ N270 Processor The ICE-945GSE comes with an embedded 45 nm 1.6 GHz Intel® ATOM™ N270 processor. The processor connects to the Intel® 945GSE Northbridge through the FSB. The processor is shown in Figure 2-4 below. Figure 2-4: Connections Some of the features of the 1.
ICE-945GSE COM Express Type 2 Module On-die 512-kB, 8-way L2 cache Support for IA 32-bit architecture Intel® Streaming SIMD Extensions-2 and -3 (Intel® SSE2 and Intel® SSE3) support and Supplemental Streaming SIMD Extension 3 (SSSE3) support Micro-FCBGA8 packaging technologies Thermal management support via Intel® Thermal Monitor 1 and Intel Thermal Monitor 2 FSB Lane Reversal for flexible routing Supports C0/C1(e)/C2(e)/C4(e) L2 Dynamic Cache Sizing Advanced power management features including Enhanced Int
ICE-945GSE COM Express Type 2 Module 2.4.2 Graphics The Intel® 945GSE Northbridge chipset has an Intel® Gen. 3.5 integrated graphics engine that supports the following display devices through connectors on the carrier board: Analog CRT LVDS TV-Out SDVO ports The graphics are interfaced to the carrier board through the COM Express connectors shown in Figure 2-4. 2.4.2.
ICE-945GSE COM Express Type 2 Module o o o 720p 1080i 1080p 2.4.2.4 SDVO The SDVO can be connected to an external chip to enable various graphics outputs. The Intel® 945GSE internal graphics engine has the following SDVO output features: Concurrent operation of PCIe x1 with SDVO One SDVO ports supported o o o o o SDVO is muxed onto the PCIe pins DVI 1.0 support for external digital monitor Only Downstream HDCP support Supports TV and DVD formats Display hot plug support 2.
ICE-945GSE COM Express Type 2 Module Integrated IDE controller supports Ultra ATA 100/66/33 Supports the four USB 2.0 devices on the ICE-945GSE with four UHCI controllers and one EHCI controller Complies with System Management Bus (SMBus) Specification, Version 2.0 Supports Audio Codec ’97 (AC’97) Revision 2.3 Supports Intel® High Definition Audio Contains Low Pin Count (LPC) interface Supports Firmware Hub (FWH) interface Serial peripheral interface support 2.5.
ICE-945GSE COM Express Type 2 Module 2.5.3 Low Pin Count (LPC) Interface The Intel® ICH7M LPC interface complies with the LPC 1.1 specifications. The LPC bus from the Intel® ICH7M can be connected to the following devices: Super I/O chipset COM port chipset 2.5.4 PCI Bus The PCI interface on the Intel® ICH7M is compliant with the PCI Revision 2.3 implementation. Some of the features of the PCI interface are listed below. PCI Revision 2.
ICE-945GSE COM Express Type 2 Module SATA controller specifications are listed below. Supports two SATA drives Supports 1.5 Gb/s data transfer speeds Supports Serial ATA Specification, Revision 1.0a 2.5.9 SPI Bus The Serial Peripheral Interface is a short distance serial bus for communication with other devices on the motherboard. The SPI interface from the board is interfaced to the items below: SPI BIOS. 2.5.
ICE-945GSE COM Express Type 2 Module Vcore +12 V +3.30 V +5.00 V VBAT The values for the above environmental parameters are all recorded in the BIOS Hardware Health Configuration menu. 2.6.2 Operating Temperature and Temperature Control The maximum and minimum operating temperatures for the ICE-945GSE are listed below. Minimum Operating Temperature: 0ºC (32°F) Maximum Operating Temperature: 60°C (140°F) A cooling fan and heat sink must be installed on the CPU.
ICE-945GSE COM Express Type 2 Module 2.6.3 Power Consumption Table 2-2 shows the power consumption parameters for the ICE-945GSE running with a 5 1.6 GHz Intel® ATOM™ N270 with 2.0 GB DDR2 memory. Voltage Current +12 V 0.
ICE-945GSE COM Express Type 2 Module Chapter 3 3 Unpacking Page 20
ICE-945GSE COM Express Type 2 Module 3.1 Anti-static Precautions WARNING: Failure to take ESD precautions during the installation of the ICE-945GSE may result in permanent damage to the ICE-945GSE and severe injury to the user. Electrostatic discharge (ESD) can cause serious damage to electronic components, including the ICE-945GSE. Dry climates are especially susceptible to ESD.
ICE-945GSE COM Express Type 2 Module 3.3 Unpacking Checklist NOTE: If some of the components listed in the checklist below are missing, please do not proceed with the installation. Contact the IEI reseller or vendor you purchased the ICE-945GSE from or contact an IEI sales representative directly. To contact an IEI sales representative, please send an email to sales@iei.com.tw. 3.3.
ICE-945GSE COM Express Type 2 Module Chapter 4 4 Connectors Page 23
ICE-945GSE COM Express Type 2 Module 4.1 Peripheral Interface Connectors Section 4.1.1 shows interface connector locations. Section 4.1.2 lists all the interface connectors seen in Section 4.1.1. 4.1.1 ICE-945GSE Layout Figure 4-1 shows the on-board peripheral connectors, backplane peripheral connectors and on-board jumpers.
ICE-945GSE COM Express Type 2 Module Figure 4-2: Connector and Jumper Locations 4.1.2 Peripheral Interface Connectors Table 4-1 shows a list of the interface connectors on the ICE-945GSE Detailed descriptions of these connectors can be found in Section 4.2.
ICE-945GSE COM Express Type 2 Module CN Location: See Figure 4-3 CN Pinouts: See Table 4-2 The standard COM Express connector locations and pinouts are shown below. Figure 4-3: COM Express Connector CD Location Pin No. Description Pin No.
ICE-945GSE COM Express Type 2 Module Pin No. Description Pin No.
ICE-945GSE COM Express Type 2 Module Pin No. Description Pin No.
ICE-945GSE COM Express Type 2 Module Pin No. Description Pin No.
ICE-945GSE COM Express Type 2 Module CN Type: 220-pin COM Express connector CN Location: See Figure 4-4 CN Pinouts: See Table 4-3 The standard COM Express connector locations and pinouts are shown below. Figure 4-4: COM Express Connector AB Location Pin No. Description Pin No.
ICE-945GSE COM Express Type 2 Module Pin No. Description Pin No.
ICE-945GSE COM Express Type 2 Module Pin No. Description Pin No.
ICE-945GSE COM Express Type 2 Module Pin No. Description Pin No.
ICE-945GSE COM Express Type 2 Module 4.2.3 SO-DIMM Connector CN Label: DIMM1 CN Type: SO-DIMM connector CN Location: See Figure 4-5 The SO-DIMM socket is for installing SO-DIMM memory. Figure 4-5: SO-DIMM Connector Location 4.2.4 SPI Connector CN Label: SPI1 CN Type: 6-pin connector CN Location: See Figure 4-6 CN Pinouts: See Table 4-4 The SPI connector is for flashing new BIOS onto the SPI BIOS chip.
ICE-945GSE COM Express Type 2 Module Figure 4-6: SPI Flash Connector Location Pin No. Description 1 SPI_VCC (+3.
ICE-945GSE COM Express Type 2 Module Chapter 5 5 Installation Page 36
ICE-945GSE COM Express Type 2 Module 5.1 Installation Considerations NOTE: The following installation notices and installation considerations should be read and understood before the CPU module is installed. All installation notices pertaining to the installation of the CPU module should be strictly adhered to. Failing to adhere to these precautions may lead to severe damage of the CPU module and injury to the person installing the CPU module.
ICE-945GSE COM Express Type 2 Module 5.2 Unpacking NOTE: If any of the items listed below are missing when the ICE-945GSE is unpacked, do not proceed with the installation and contact the ICE-945GSE reseller or vendor. 5.2.1 Unpacking Precautions Before installing the ICE-945GSE, unpack the CPU module. Some components on ICE-945GSE are very sensitive to static electricity and can be damaged by a sudden rush of power.
ICE-945GSE COM Express Type 2 Module 5.3 SO-DIMM Installation To install a SO-DIMM into a SO-DIMM socket, please follow the steps below and refer to Figure 5-1. Figure 5-1: SO-DIMM Installation Step 1: Locate the SO-DIMM socket. Place the ICE-945GSE on an anti-static pad. Step 2: Align the SO-DIMM with the socket. The SO-DIMM must be oriented in such a way that the notch in the middle of the SO-DIMM must be aligned with the plastic bridge in the socket. Step 3: Insert the SO-DIMM.
ICE-945GSE COM Express Type 2 Module 5.4 Jumper Settings NOTE: A jumper is a metal bridge used to close an electrical circuit. It consists of two or three metal pins and a small metal clip (often protected by a plastic cover) that slides over the pins to connect them. To CLOSE/SHORT a jumper means connecting the pins of the jumper with the plastic clip and to OPEN a jumper means removing the plastic clip from a Jumper Locations jumper.
ICE-945GSE COM Express Type 2 Module Figure 5–2: Jumper Locations 5.4.1 LVDS Panel Resolution Jumper Label: SW1 Jumper Type: 4-in-1 switch Jumper Settings: See Table 5-2 Jumper Location: See Figure 5–2 This switch sets the resolution of the panel attached to the LVDS output. Settings are shown in Table 5-2.
ICE-945GSE COM Express Type 2 Module 5.4.2 BIOS Selection Jumper Label: SW2 Jumper Type: 4-in-1 switch Jumper Settings: See Table 5-3 Jumper Location: See Figure 5–2 This jumper selects which BIOS to use. There is a BIOS included on the ICE-945GSE, but a BIOS connected to the LPC or PCI bus can be used instead. The clear CMOS jumper settings are shown in Table 5-3. 1 2 3 4 Description OFF ON OFF OFF SPI ON OFF OFF OFF LPC OFF OFF OFF OFF PCI Table 5-3: BIOS Selection 5.
ICE-945GSE COM Express Type 2 Module WARNING! Please note that the installation instructions described in this manual should be carefully followed in order to avoid damage to the CPU module components and injury to the user. WARNING! When installing electronic components onto the embedded module or installing the embedded module onto the baseboard, always take anti-static precautions in order to prevent ESD damage to the CPU module and other electronic components like the CPU and SO-DIMM module.
ICE-945GSE COM Express Type 2 Module Chapter 6 6 BIOS Setup Page 44
ICE-945GSE COM Express Type 2 Module 6.1 Introduction NOTE: The BIOS items shown below are from a ICE-945GSE installed on the ICE-DB-9S-R10 reference carrier board. The ICE-DB-9S-R10 reference carrier board is available from iEi, contact sales@iei.com.tw or go to http://www.ieiworld.com for more information. The BIOS is programmed onto the BIOS chip. The BIOS setup program allows changes to certain system settings. This chapter outlines the options that can be changed. 6.1.
ICE-945GSE COM Express Type 2 Module Key Function Esc key Main Menu – Quit and not save changes into CMOS Status Page Setup Menu and Option Page Setup Menu -Exit current page and return to Main Menu Page Up key Increase the numeric value or make changes Page Dn key Decrease the numeric value or make changes F1 key General help, only for Status Page Setup Menu and Option Page Setup Menu F2 /F3 key Change color from total three colors. F2 to select color forward.
ICE-945GSE COM Express Type 2 Module The following sections completely describe the configuration options found in the menu items at the top of the BIOS screen and listed above. 6.2 Main The Main BIOS menu (BIOS Menu 1) appears when the BIOS Setup program is entered. The Main menu gives an overview of the basic system information. Main Advanced PCIPNP BIOS SETUP UTILITY Boot Security Chipset System Overview ⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯ AMIBIOS Version :08.00.
ICE-945GSE COM Express Type 2 Module o Count: The number of CPUs on the motherboard System Memory: Displays the auto-detected system memory. o Size: Lists memory size The System Overview field also has two user configurable fields: System Time [xx:xx:xx] Use the System Time option to set the system time. Manually enter the hours, minutes and seconds. System Date [xx/xx/xx] Use the System Date option to set the system date. Manually enter the day, month and year. 6.
ICE-945GSE COM Express Type 2 Module Main Advanced PCIPNP BIOS SETUP UTILITY Boot Security Chipset Advanced Settings ⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯ WARNING: Setting wrong values in below sections may cause system to malfunction > > > > > > > > > > CPU Configuration IDE Configuration Floppy Configuration SuperIO Configuration W83627DHG-P Hardware Health NCT7802 Hardware Health Configuration Power Configuration Remote Access Configuration USB Configuration iEi Feature Exit Configure CPU ↑ ↓ Enter F
ICE-945GSE COM Express Type 2 Module Manufacturer: Lists the name of the CPU manufacturer Brand String: Lists the brand name of the CPU being used Frequency: Lists the CPU processing speed FSB Speed: Lists the FSB speed Cache L1: Lists the CPU L1 cache size Cache L2: Lists the CPU L2 cache size 6.3.2 IDE Configuration Use the IDE Configuration menu (BIOS Menu 4) to change and/or set the configuration of the IDE devices installed in the system.
ICE-945GSE COM Express Type 2 Module Configures the on-board ATA/IDE controller to be in Enhanced Enhanced mode. In this mode, IDE channels and SATA channels are separated. This mode supports up to 6 storage devices. Some legacy OS do not support this mode. Legacy IDE Channels [SATA Pri, PATA Sec] Only the SATA drives are enabled. SATA Only SATA Pri, PATA Sec DEFAULT The SATA drives are enabled on the Primary IDE channel. The IDE drives are enabled on the Secondary IDE channel.
ICE-945GSE COM Express Type 2 Module Main Advanced PCIPNP BIOS SETUP UTILITY Boot Security Chipset Primary IDE Master ⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯ Device :Not Detected Type LBA/Large Mode Block (Multi-Sector Transfer) PIO Mode DMA Mode S.M.A.R.T. 32Bit Data Transfer [Auto] [Auto] [Auto] [Auto] [Auto] [Auto] [Enabled] Exit Select the type of device connected to the system ↑ ↓ Enter F1 F10 ESC Select Screen Select Item Go to SubScreen General Help Save and Exit Exit v02.
ICE-945GSE COM Express Type 2 Module Type [Auto] Use the Type BIOS option select the type of device the AMIBIOS attempts to boot from after the Power-On Self-Test (POST) is complete. BIOS is prevented from searching for an IDE disk Not Installed drive on the specified channel. Auto DEFAULT The BIOS auto detects the IDE disk drive type attached to the specified channel. This setting should be used if an IDE hard disk drive is attached to the specified channel.
ICE-945GSE COM Express Type 2 Module BIOS is prevented from using Multi-Sector Transfer on the Disabled specified channel. The data to and from the device occurs one sector at a time. Auto DEFAULT BIOS auto detects Multi-Sector Transfer support on the drive on the specified channel. If supported the data transfer to and from the device occurs multiple sectors at a time.
ICE-945GSE COM Express Type 2 Module S.M.A.R.T [Auto] Use the S.M.A.R.T option to auto-detect, disable or enable Self-Monitoring Analysis and Reporting Technology (SMART) on the drive on the specified channel. S.M.A.R.T predicts impending drive failures. The S.M.A.R.T BIOS option enables or disables this function. Auto DEFAULT BIOS auto detects HDD SMART support. Disabled Prevents BIOS from using the HDD SMART feature.
ICE-945GSE COM Express Type 2 Module Main Advanced PCIPNP BIOS SETUP UTILITY Boot Security Chipset Floppy Configuration ⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯ Floppy A [Disabled] Exit Allows BIOS to select Serial Port Base Addresses ↑ ↓ Enter F1 F10 ESC Select Screen Select Item Go to SubScreen General Help Save and Exit Exit v02.61 ©Copyright 1985-2006, American Megatrends, Inc. BIOS Menu 6: Floppy Configuration Floppy A/B Use the Floppy A/B option to configure the floppy disk drive.
ICE-945GSE COM Express Type 2 Module 6.3.4 Super IO Configuration Use the Super IO Configuration menu (BIOS Menu 7) to set or change the configurations for the FDD controllers, parallel ports and serial ports.
ICE-945GSE COM Express Type 2 Module Serial Port2 Address [2F8/IRQ3] Use the Serial Port2 Address option to select the Serial Port 2 base address.
ICE-945GSE COM Express Type 2 Module Bi-directional Parallel port outputs are 8-bits long. Inputs are accomplished by reading 4 of the 8 bits on the status register. The ECP parallel port operates in the extended capabilities port (ECP) mode. The ECP mode supports bi-directional communication between the system and the parallel port device and the transmission rates between the two are much faster than the Normal mode The parallel port operates in the enhanced parallel EPP port mode (EPP).
ICE-945GSE COM Express Type 2 Module Serial Port3 Address [3E8] Use the Serial Port3 Address option to select the base addresses for serial port 3 No base address is assigned to serial port 3 Disabled 3E8 DEFAULT Serial port 3 I/O port address is 3E8 2E8 Serial port 3 I/O port address is 2E8 2F0 Serial port 3 I/O port address is 2F0 2E0 Serial port 3 I/O port address is 2E0 Serial Port3 IRQ [11] Use the Serial Port3 IRQ option to select the interrupt address for serial port 3.
ICE-945GSE COM Express Type 2 Module Serial Port5 Address [2F0] Use the Serial Port5 IRQ option to select the interrupt address for serial port 5. Disabled No base address is assigned to serial port 5 3E8 Serial port 5 I/O port address is 3E8 2E8 Serial port 5 I/O port address is 2E8 2F0 DEFAULT Serial port 5 I/O port address is 2F0 Serial port 5 I/O port address is 2E0 2E0 Serial Port5 IRQ [11] Use the Serial Port5 IRQ option to select the interrupt address for serial port 5.
ICE-945GSE COM Express Type 2 Module Select RS232 or RS422/RS485 [RS232] Use the Select RS232 or RS422/RS485 option to select the Serial Port 6 signaling mode. RS232 DEFAULT Serial Port 6 signaling mode is RS-232 Serial Port 6 signaling mode is RS-422/485 RS422/RS485 6.3.5 W83627DHG-P Hardware Health The W83627DHG-P Hardware Health menu (BIOS Menu 8) shows the operating 5 temperature, fan speeds and system voltages.
ICE-945GSE COM Express Type 2 Module FAN1 PWM Control [070] This value specifies the speed of the fan. Use the + or – key to change the value. PWM Minimum Mode: 0 PWM Maximum Mode: 255 CPU FAN1 PWM Control [070] This value specifies the speed of the CPU fan. Use the + or – key to change the value. PWM Minimum Mode: 0 PWM Maximum Mode: 255 6.3.6 NCT7802 Hardware Health Configuration The NCT7802 Hardware Health Configuration menu (BIOS Menu 9) shows the operating temperature, fan speeds and system voltages.
ICE-945GSE COM Express Type 2 Module Manual mode DEFAULT The fan spins at the speed set in: Fan PWM control SmartFan mode The fan adjusts its speed using these settings: Temperature Level 1 Temperature Level 2 Temperature Level 3 Temperature Level 4 Temperature Critical FAN1 PWM Control [070] This value specifies the speed of the fan. Use the + or – key to change the value. PWM Minimum Mode: 0 PWM Maximum Mode: 255 Hardware Health Monitoring The following system parameters and values are shown.
ICE-945GSE COM Express Type 2 Module 6.3.7 Power Configuration The Power Configuration menu (BIOS Menu 10) allows the advanced power management options to be configured. Main Advanced PCIPNP BIOS SETUP UTILITY Boot Security Select AT/ATX Power Chipset [ATX Power] Exit Set the ACPI state used for System suspend > ACPI Configuration > APM Configuration Select Screen ↑ ↓ Select Item Enter Go to SubScreen F1 General Help F10 Save and Exit ESC Exit v02.
ICE-945GSE COM Express Type 2 Module Main Advanced PCIPNP BIOS SETUP UTILITY Boot Security Chipset ACPI Settings ⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯ Suspend mode [S1 (POS)] Exit Set the ACPI state used for System suspend ↑ ↓ Enter F1 F10 ESC Select Screen Select Item Go to SubScreen General Help Save and Exit Exit v02.61 ©Copyright 1985-2006, American Megatrends, Inc.
ICE-945GSE COM Express Type 2 Module Main Advanced PCIPNP BIOS SETUP UTILITY Boot Security Chipset APM Configuration ⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯ Restore on AC Power Loss [Last State] Power Button Mode [On/Off] Advanced Resume Event Controls Resume on Keyboard/Mouse Resume on PME# Resume On RING/PCI-E Wake# Resume on RTC Alarm [Disabled] [Disabled] [Enabled] [Disabled] Exit Go into On/Off, or Suspend when Power button is pressed ↑ ↓ Enter F1 F10 ESC Select Screen Select Item Go to SubScreen Ge
ICE-945GSE COM Express Type 2 Module Resume on Keyboard/Mouse [Disabled] Use the Resume on Keyboard/Mouse BIOS option to enable activity on either the keyboard or mouse to rouse the system from a suspend or standby state. That is, the system is roused when the mouse is moved or a button on the keyboard is pressed.
ICE-945GSE COM Express Type 2 Module Resume On RTC Alarm [Disabled] Use the Resume On RTC Alarm option to specify the time the system should be roused from a suspended state. Disabled DEFAULT The real time clock (RTC) cannot generate a wake event If selected, the following appears with values that Enabled can be selected: RTC Alarm Date (Days) System Time After setting the alarm, the computer turns itself on from a suspend state when the alarm goes off. 6.3.
ICE-945GSE COM Express Type 2 Module Remote Access [Disabled] Use the Remote Access option to enable or disable access to the remote functionalities of the system. Disabled DEFAULT Remote access is disabled. Remote access configuration options shown below Enabled appear: Serial Port Number Serial Port Mode Redirection after BIOS POST Terminal Type These configuration options are discussed below.
ICE-945GSE COM Express Type 2 Module Serial Port Mode [115200 8,n,1] Use the Serial Port Mode option to select baud rate through which the console redirection is made.
ICE-945GSE COM Express Type 2 Module 6.3.9 USB Configuration Use the USB Configuration menu (BIOS Menu 14) to read USB configuration information and configure the USB settings. Main Advanced PCIPNP BIOS SETUP UTILITY Boot Security Chipset USB Configuration ⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯ Module Version – 2.24.3-13.4 Exit Enables USB host controllers USB Devices Enabled: None USB Function USB 2.0 Controller Legacy USB Support USB 2.
ICE-945GSE COM Express Type 2 Module Normally if this option is not enabled, any attached USB mouse or USB keyboard does not become available until a USB compatible operating system is fully booted with all USB drivers loaded. When this option is enabled, any attached USB mouse or USB keyboard can control the system even when there is no USB driver loaded onto the system.
ICE-945GSE COM Express Type 2 Module Auto Recovery Function [Disabled] Use the Auto Recovery Function BIOS option to enable or disable the auto recovery function of the IEI One Key Recovery. Disabled DEFAULT Enabled Auto recovery function disabled Auto recovery function enabled 6.4 PCI/PnP Use the PCI/PnP menu (BIOS Menu 16) to configure advanced PCI and PnP settings. WARNING! Setting wrong values for the BIOS selections in the PCIPnP BIOS menu may cause the system to malfunction.
ICE-945GSE COM Express Type 2 Module Main Advanced PCIPNP BIOS SETUP UTILITY Boot Security Chipset Advanced PCI/PnP Settings ⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯ WARNING: Setting wrong values in below sections may cause system to malfunction IRQ3 [Reserved] IRQ4 [Reserved] IRQ5 [Available] IRQ7 [Available] IRQ9 [Available] IRQ10 [Available] IRQ11 [Reserved] IRQ14 [Available] IRQ15 [Available] DMA DMA DMA DMA DMA DMA Channel Channel Channel Channel Channel Channel 0 1 3 5 6 7 [Available] [Available] [Ava
ICE-945GSE COM Express Type 2 Module IRQ9 IRQ10 IRQ 11 IRQ 14 IRQ 15 DMA Channel# [Available] Use the DMA Channel# option to assign a specific DMA channel to a particular PCI/PnP device.
ICE-945GSE COM Express Type 2 Module 6.5 Boot Use the Boot menu (BIOS Menu 17) to configure system boot options. Main Advanced PCIPNP BIOS SETUP UTILITY Boot Security Chipset Boot Settings ⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯ > Boot Settings Configuration Exit Configure settings during system boot. ↑ ↓ Enter F1 F10 ESC Select Screen Select Item Go to SubScreen General Help Save and Exit Exit v02.61 ©Copyright 1985-2006, American Megatrends, Inc. BIOS Menu 17: Boot 6.5.
ICE-945GSE COM Express Type 2 Module Quick Boot [Enabled] Use the Quick Boot BIOS option to make the computer speed up the boot process. No POST procedures are skipped Disabled Enabled DEFAULT Some POST procedures are skipped to decrease the system boot time Quiet Boot [Enabled] Use the Quiet Boot BIOS option to select the screen display when the system boots.
ICE-945GSE COM Express Type 2 Module On DEFAULT Allows the Number Lock on the keyboard to be enabled automatically when the computer system boots up. This allows the immediate use of the 10-key numeric keypad located on the right side of the keyboard. To confirm this, the Number Lock LED light on the keyboard is lit. Boot From LAN Support [Disabled] Use the BOOT From LAN Support option to enable the system to be booted from a remote system.
ICE-945GSE COM Express Type 2 Module Change Supervisor Password Use the Change Supervisor Password to set or change a supervisor password. The default for this option is Not Installed. If a supervisor password must be installed, select this field and enter the password. After the password has been added, Install appears next to Change Supervisor Password. Change User Password Use the Change User Password to set or change a user password. The default for this option is Not Installed.
ICE-945GSE COM Express Type 2 Module Main Advanced PCIPNP BIOS SETUP UTILITY Boot Security Chipset Exit Advanced Chipset Settings ⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯ WARNING: Setting wrong values in below section may cause system to malfunction. > North Bridge Configuration > South Bridge Configuration ↑ ↓ Enter F1 F10 ESC Select Screen Select Item Go to SubScreen General Help Save and Exit Exit v02.61 ©Copyright 1985-2006, American Megatrends, Inc. BIOS Menu 20: Chipset 6.7.
ICE-945GSE COM Express Type 2 Module ISA expansion card is used, please refer to the documentation that came with the card to see if it is necessary to reserve the space. Disabled DEFAULT Memory is not reserved for ISA expansion cards Between 15 MB and 16 MB of memory is reserved 15 MB–16 MB for ISA expansion cards Internal Graphics Mode Select [Enable, 8 MB] Use the Internal Graphic Mode Select option to specify the amount of system memory that can be used by the Internal graphics device.
ICE-945GSE COM Express Type 2 Module Main Advanced PCIPNP BIOS SETUP UTILITY Boot Security Chipset Exit Video Function Configuration ⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯ DVMT Mode Select [DVMT Mode] DVMT/Fixed Memory [Maximum DVMT] Boot Display Device LVDS Panel Type LVDS1 Current Jumper Setting [Auto] [1024x768 18b] [640x480 18b] Backlight Control [Inverted] TV Standard [VBIOS-Default] ↑ ↓ Enter F1 F10 ESC Select Screen Select Item Go to SubScreen General Help Save and Exit Exit v02.
ICE-945GSE COM Express Type 2 Module 64 MB 128 MB Maximum DVMT Default Boot Display Device Use the Boot Display Device option to select the display device used by the system when it boots. Configuration options are listed below. Auto DEFAULT CRT TV LFP LVDS Panel Type [1024x768 18b] Use the LVDS Panel Type option to select the type of flat panel connected to the system. Configuration options are listed below.
ICE-945GSE COM Express Type 2 Module TV Standard [Auto] Use the TV Standard option to select the standard of the television connected to the system. The configuration options are listed below. VBIOS-Default DEFAULT NTSC PAL SECAM SMPTE240M ITU-R television SMPTE295M SMPTE296M EIA-770.2 EIA-770.3 6.7.2 South Bridge Configuration Use the South Bridge Configuration menu (BIOS Menu 23) to configure the Northbridge chipset.
ICE-945GSE COM Express Type 2 Module Audio Controller [Azalia] Use the Audio Controller option to enable or disable the audio codec. Azalia DEFAULT The onboard HD Audio codec is enabled Disable all audio codec. All Disabled Spread Spectrum Clock [Disabled] Use the Spread Spectrum Clock option to reduce the EMI. Excess EMI is generated when the system clock generator pulses have extreme values.
ICE-945GSE COM Express Type 2 Module Save Changes and Exit Use the Save Changes and Exit option to save the changes made to the BIOS options and to exit the BIOS configuration setup program. Discard Changes and Exit Use the Discard Changes and Exit option to exit the BIOS configuration setup program without saving the changes made to the system. Discard Changes Use the Discard Changes option to discard the changes and remain in the BIOS configuration setup program.
ICE-945GSE COM Express Type 2 Module Chapter 7 7 Software Installation Page 88
ICE-945GSE COM Express Type 2 Module 7.1 Available Software Drivers NOTE: The content of the CD may vary throughout the life cycle of the product and is subject to change without prior notice. Visit the IEI website or contact technical support for the latest updates. The following drivers can be installed on the system: 7.3 Chipset Driver Installation....................................................................... 91 7.4 VGA Driver Installation .....................................................
ICE-945GSE COM Express Type 2 Module Step 2: The screen in Figure 7-1 appears. Figure 7-1: Start Up Screen Step 3: Click ICE-945GSE. Step 4: The screen in Figure 7-2 appears. Figure 7-2: Select Operating System Step 5: Select the operating system installed on the ICE-945GSE system. This manual describes the installation for a Windows XP operating system.
ICE-945GSE COM Express Type 2 Module Step 6: The list of drivers in Figure 7-3 appears. Figure 7-3: Drivers 7.3 Chipset Driver Installation To install the chipset driver, please do the following. Step 1: Access the driver list shown in Figure 7-3. (See Section 7.2) Step 2: Click “1-Chipset Driver” Step 3: When the setup files are completely extracted the Welcome Screen in Figure 7-4 appears.
ICE-945GSE COM Express Type 2 Module Figure 7-4: Chipset Driver Welcome Screen Step 4: Click Next to continue. Step 5: The license agreement in Figure 7-5 appears. Figure 7-5: Chipset Driver License Agreement Step 6: Read the License Agreement. Step 7: Click the YES button to accept the license agreement and continue.
ICE-945GSE COM Express Type 2 Module Step 8: The Read Me file in Figure 7-6 appears. Figure 7-6: Chipset Driver Read Me File Step 9: Click NEXT to continue. Step 10: Setup Operations are performed as shown in Figure 7-7. Figure 7-7: Chipset Driver Setup Operations Step 11: Once the Setup Operations are complete, click the NEXT icon to continue.
ICE-945GSE COM Express Type 2 Module Step 12: The Finish screen appears. Figure 7-8: Chipset Driver Installation Finish Screen Step 13: Select “Yes, I want to restart the computer now” and click the Finish icon. See Figure 7-8. 7.4 VGA Driver Installation To install the VGA driver, please do the following. Step 1: Access the driver list shown in Figure 7-3. (See Section 7.2) Step 2: Click “2-VGA” Step 3: The VGA Read Me file in Figure 7-9 appears.
ICE-945GSE COM Express Type 2 Module Figure 7-9: VGA Driver Read Me File Step 4: Click NEXT to continue. Step 5: The installation files are extracted. See Figure 7-10. Figure 7-10: VGA Driver Setup Files Extracted Step 6: The Welcome Screen in Figure 7-11 appears.
ICE-945GSE COM Express Type 2 Module Figure 7-11: VGA Driver Welcome Screen Step 7: Click NEXT to continue. Step 8: The license agreement in Figure 7-12 appears. Figure 7-12: VGA Driver License Agreement Step 9: Read the License Agreement. Step 10: Click YES to accept the license agreement and continue.
ICE-945GSE COM Express Type 2 Module Step 11: The Readme file in Figure 7-13 appears. Figure 7-13: VGA Driver Read Me File Step 12: Click NEXT to continue. Step 13: Setup Operations are performed as shown in Figure 7-14. NOTE: The “Found New Hardware Wizard” will appear and then disappear during this step. Do not adjust any settings in the “Found New Hardware Wizard” window.
ICE-945GSE COM Express Type 2 Module Figure 7-14: VGA Driver Setup Operations Step 14: Once the Setup Operations are complete, click NEXT to continue. Step 15: The Finish screen appears. Figure 7-15: VGA Driver Installation Finish Screen Step 16: Select “Yes, I want to restart the computer now” and click FINISH . See Figure 7-15.
ICE-945GSE COM Express Type 2 Module 7.5 LAN Driver Installation To install the chipset driver, please do the following. Step 1: Access the driver list shown in Figure 7-3. (See Section 7.2) Step 2: Click “3-LAN” Step 3: The Welcome screen in Figure 7-16 appears. Figure 7-16: LAN Driver Welcome Screen Step 4: Click NEXT to continue. Step 5: The Ready to Install screen in Figure 7-17 appears.
ICE-945GSE COM Express Type 2 Module Figure 7-17: LAN Driver Welcome Screen Step 6: Click NEXT to proceed with the installation. Step 7: The program begins to install. Step 8: The installation progress can be monitored in the progress bar shown in Figure 7-18. Figure 7-18: LAN Driver Installation Step 9: When the driver installation is complete, the screen in Figure 7-19 appears.
ICE-945GSE COM Express Type 2 Module Figure 7-19: LAN Driver Installation Complete Step 10: Click FINISH to exit the InstallShield Wizard (Figure 7-19). 7.6 Audio Driver Installation There is no audio driver on the ICE-945GSE. To add audio capabilities to the ICE-945GSE, connect a HD Audio kit or AC’97 audio kit available from IEI. Follow the installation applicable to the installed audio kit. 7.6.1 AC’97 Driver Installation To install the chipset driver, please do the following.
ICE-945GSE COM Express Type 2 Module Figure 7-20: AC'97 Audio Step 3: Browse to “E:\4-Audio\ALC665\Windows\Windows 98Gold, 98se, Me, 2000, XP, 2003(32,64 bits)\A3.
ICE-945GSE COM Express Type 2 Module Step 4: Double-click the installation file in Figure 7-21. Step 5: The AC’97 Driver Installation screen in Figure 7-22 appears. Figure 7-22: AC’97 Driver Installation Welcome Screen Step 6: Click NEXT to continue. Step 7: The Verification window in Figure 7-23 may appear.
ICE-945GSE COM Express Type 2 Module Step 8: Click CONTINUE ANYWAY . Step 9: When the driver is installed, the driver installation finish screen in Figure 7-24 appears. Figure 7-24: AC’97 Driver Installation Complete Step 10: Select “Yes, I wish to restart my computer now” And click FINISH to exit the InstallShield Wizard and restart the computer.Step 0: 7.6.2 HD Audio Driver Installation To install the chipset driver, please do the following. Step 1: Access the driver list shown in Figure 7-3.
ICE-945GSE COM Express Type 2 Module Figure 7-25: HD Audio Step 3: Browse to “E:\4-Audio\ALC883\Windows\Windows 2000, XP, 2003(32,64 bits)” Figure 7-26 Figure 7-26: HD Audio Driver Options Page 105
ICE-945GSE COM Express Type 2 Module Step 4: Double-click the installation file in Figure 7-26. Step 5: The AC’97 Driver Installation screen in Figure 7-27 appears. Figure 7-27: HD Audio Driver Installation Welcome Screen Step 6: Click NEXT to continue. Step 7: When the driver is installed, the driver installation finish screen in Figure 7-28 appears.
ICE-945GSE COM Express Type 2 Module Step 8: Select “Yes, I wish to restart my computer now” And click FINISH to exit the InstallShield Wizard and restart the computer.Step 0: 7.7 iSMM Installation The iSMM (Intelligent System Management Module) allows hardware functions to be monitored from within the operating system. The iSMM can be set to sound an alarm when voltages, temperatures or fan speeds rise above or fall below the set limits. Step 1: Access the driver list shown in Figure 7-3. (See Section 7.
ICE-945GSE COM Express Type 2 Module Step 5: The contents of the directory are displayed. (Figure 7-30) Figure 7-30: iSMM Installation File Step 6: Double click the iSMM EN V1.11.00 setup file. (Figure 7-30) Step 7: The iSMM InstallShield Welcome Screen appears. (Figure 7-31) Figure 7-31: iSMM InstallShield Welcome Screen Step 8: Click NEXT to continue.
ICE-945GSE COM Express Type 2 Module Step 9: The License Agreement screen appears. (Figure 7-32) Figure 7-32: iSMM License Agreement Step 10: Select “I accept the terms of the license agreement.” (Figure 7-32) Step 11: Click NEXT to continue.
ICE-945GSE COM Express Type 2 Module Step 12: The Customer Information screen appears.(Figure 7-33) Figure 7-33: iSMM Customer Information Step 13: Fill in the “User Name” and “Organization” fields, which will be automatically filled with the settings for the current user.(Figure 7-33) Step 14: Click Next to continue.
ICE-945GSE COM Express Type 2 Module Step 15: The Setup Type screen appears. (Figure 7-34) Figure 7-34: iSMM Setup Type Step 16: Select “Complete” (Figure 7-34) Step 17: Click NEXT to continue.
ICE-945GSE COM Express Type 2 Module Step 18: The Installation Confirmation screen appears. (Figure 7-35) Figure 7-35: iSMM Installation Confirmation Step 19: Click INSTALL to begin installing the drivers. (Figure 7-35) Step 20: The InstallShield Wizard Completed appears when the drivers are finished installing.
ICE-945GSE COM Express Type 2 Module Step 21: Click FINISH to exit the installation program.(Figure 7-36) Step 22: The Restart Confirmation screen appears.(Figure 7-37) Figure 7-37: iSMM Restart Confirmation Step 23: Select YES to restart the system, or NO to restart the system manually later.
ICE-945GSE COM Express Type 2 Module Appendix A A BIOS Options Page 114
ICE-945GSE COM Express Type 2 Module Below is a list of BIOS configuration options in the BIOS chapter. System Overview .................................................................................................................47 System Time [xx:xx:xx] .......................................................................................................48 System Date [xx/xx/xx] ........................................................................................................
ICE-945GSE COM Express Type 2 Module FAN1 Mode Setting [Manual Mode]....................................................................................63 FAN1 PWM Control [070].....................................................................................................64 Hardware Health Monitoring ...............................................................................................64 Select AT/ATX Power [ATX Power] ..........................................................................
ICE-945GSE COM Express Type 2 Module DVMT Mode Select [DVMT Mode].......................................................................................83 DVMT/FIXED Memory [Maximum DVMT] ...........................................................................83 Boot Display Device ............................................................................................................84 LVDS Panel Type [1024x768 18b].....................................................................................
ICE-945GSE COM Express Type 2 Module Appendix B B Terminology Page 118
ICE-945GSE COM Express Type 2 Module AC ’97 Audio Codec 97 (AC’97) refers to a codec standard developed by Intel® in 1997. ACPI Advanced Configuration and Power Interface (ACPI) is an OS-directed configuration, power management, and thermal management interface. AHCI Advanced Host Controller Interface (AHCI) is a SATA Host controller register-level interface. ATA The Advanced Technology Attachment (ATA) interface connects storage devices including hard disks and CD-ROM drives to a computer.
ICE-945GSE COM Express Type 2 Module DMA Direct Memory Access (DMA) enables some peripheral devices to bypass the system processor and communicate directly with the system memory. DIMM Dual Inline Memory Modules are a type of RAM that offer a 64-bit data bus and have separate electrical contacts on each side of the module. DIO The digital inputs and digital outputs are general control signals that control the on/off circuit of external devices or TTL devices.
ICE-945GSE COM Express Type 2 Module LCD Liquid crystal display (LCD) is a flat, low-power display device that consists of two polarizing plates with a liquid crystal panel in between. LVDS Low-voltage differential signaling (LVDS) is a dual-wire, high-speed differential electrical signaling system commonly used to connect LCD displays to a computer. POST The Power-on Self Test (POST) is the pre-boot actions the system performs when the system is turned-on.
ICE-945GSE COM Express Type 2 Module Appendix C C Watchdog Timer Page 122
ICE-945GSE COM Express Type 2 Module NOTE: The following discussion applies to DOS environment. IEI support is contacted or the IEI website visited for specific drivers for more sophisticated operating systems, e.g., Windows and Linux. The Watchdog Timer is provided to ensure that standalone systems can always recover from catastrophic conditions that cause the CPU to crash. This condition may have occurred by external EMIs or a software bug.
ICE-945GSE COM Express Type 2 Module NOTE: When exiting a program it is necessary to disable the Watchdog Timer, otherwise the system resets.
ICE-945GSE COM Express Type 2 Module Appendix D D Address Mapping Page 125
ICE-945GSE COM Express Type 2 Module D.1 Direct Memory Access (DMA) Figure D-1: Direct Memory Access (DMA) D.
ICE-945GSE COM Express Type 2 Module Figure D-3: Input/Output (IO) (2 of 2) D.
ICE-945GSE COM Express Type 2 Module D.
ICE-945GSE COM Express Type 2 Module Appendix E E Compatibility Page 129
ICE-945GSE COM Express Type 2 Module NOTE: The compatible items described here have been tested by the IEI R&D team and found to be compatible with the ICE-945GSE E.1 Compatible Operating Systems The following operating systems have been successfully run on the ICE-945GSE. Microsoft® Windows Vista Microsoft® Windows XP (32-bit) Microsoft® Windows 2000 Fedora 7 E.
ICE-945GSE COM Express Type 2 Module E.3 Compatible Memory Modules NOTE: The memory modules listed below have been tested on the ICE-945GSE other memory modules that comply with the specifications may also work on the ICE-945GSE but have not been tested. The following memory modules have been successfully tested on the ICE-945GSE. Manufacturer Transcend Capacity 2.
ICE-945GSE COM Express Type 2 Module Appendix F F Hazardous Materials Disclosure Page 132
ICE-945GSE COM Express Type 2 Module F.1 Hazardous Materials Disclosure Table for IPB Products Certified as RoHS Compliant Under 2002/95/EC Without Mercury The details provided in this appendix are to ensure that the product is compliant with the Peoples Republic of China (China) RoHS standards. The table below acknowledges the presences of small quantities of certain materials in the product, and is applicable to China RoHS only.
ICE-945GSE COM Express Type 2 Module Part Name Toxic or Hazardous Substances and Elements Lead Mercury Cadmium Hexavalent Polybrominated Polybrominated (Pb) (Hg) (Cd) Chromium Biphenyls Diphenyl (CR(VI)) (PBB) Ethers (PBDE) Housing X O O O O X Display X O O O O X Printed Circuit X O O O O X X O O O O O X O O O O X Fan Assembly X O O O O X Power Supply X O O O O X O O O O O O Board Metal Fasteners Cable Assembly Assemblies Battery O: This
ICE-945GSE COM Express Type 2 Module 此附件旨在确保本产品符合中国 RoHS 标准。以下表格标示此产品中某有毒物质的含量符 合中国 RoHS 标准规定的限量要求。 本产品上会附有”环境友好使用期限”的标签，此期限是估算这些物质”不会有泄漏或突变”的 年限。本产品可能包含有较短的环境友好使用期限的可替换元件，像是电池或灯管，这些元 件将会单独标示出来。 部件名称 有毒有害物质或元素 铅 汞 镉 六价铬 多溴联苯 多溴二苯 (Pb) (Hg) (Cd) (CR(VI)) (PBB) 醚 (PBDE) 壳体 X O O O O X 显示 X O O O O X 印刷电路板 X O O O O X 金属螺帽 X O O O O O 电缆组装 X O O O O X 风扇组装 X O O O O X 电力供应组装 X O O O O X 电池 O O O O O O O: 表示该有毒有害物质在该部件所有物质材料中的含量均在 SJ/T11363-2
