Manual

ManualsBrandsIEI Integration ManualsHardwareICE-QM770

ICE-QM770 COM Express Module

Page i

IEI Technology Corp.

User Manual

COM Express R2.0 Module (Type 6),

Socket G2 Supports 2nd and 3rd Generation Intel® Core™

i7/i5/i3, Pentium® and Celeron® Processors, DDR3 and RoHS

MODEL:

ICE-QM770

Rev. 1.01 – 17 April, 2013

Summary of content (168 pages)

PAGE 1
ICE-QM770 COM Express Module IEI Technology Corp. MODEL: ICE-QM770 COM Express R2.0 Module (Type 6), Socket G2 Supports 2nd and 3rd Generation Intel® Core™ i7/i5/i3, Pentium® and Celeron® Processors, DDR3 and RoHS User Manual Page i Rev. 1.
PAGE 2
ICE-QM770 COM Express Module Revision Date Version Changes 17 April, 2013 1.01 Updated Section 4.6: Mounting the ICE-QM770 to an Optional Baseboard 11 January, 2013 Page ii 1.
PAGE 3
ICE-QM770 COM Express Module Copyright COPYRIGHT NOTICE The information in this document is subject to change without prior notice in order to improve reliability, design and function and does not represent a commitment on the part of the manufacturer. In no event will the manufacturer be liable for direct, indirect, special, incidental, or consequential damages arising out of the use or inability to use the product or documentation, even if advised of the possibility of such damages.
PAGE 4
ICE-QM770 COM Express Module Table of Contents 1 INTRODUCTION.......................................................................................................... 1 1.1 INTRODUCTION........................................................................................................... 2 1.2 FEATURES ................................................................................................................... 2 1.3 CONNECTORS .....................................................................
PAGE 5
ICE-QM770 COM Express Module 4.5.1 LVDS Panel Type Selection.............................................................................. 33 4.6 MOUNTING THE ICE-QM770 TO AN OPTIONAL BASEBOARD....................................... 34 5 BIOS .............................................................................................................................. 38 5.1 INTRODUCTION......................................................................................................... 39 5.1.
PAGE 6
ICE-QM770 COM Express Module 5.4.2.3 Memory Configuration ............................................................................. 71 5.5 BOOT........................................................................................................................ 72 5.6 SECURITY ................................................................................................................. 74 5.7 SAVE & EXIT ...............................................................................................
PAGE 7
ICE-QM770 COM Express Module B.6.1 Configure DHCP Server Settings .................................................................. 136 B.6.2 Configure TFTP Settings ............................................................................... 137 B.6.3 Configure One Key Recovery Server Settings ............................................... 138 B.6.4 Start the DHCP, TFTP and HTTP ................................................................. 139 B.6.5 Create Shared Directory.........................
PAGE 8
ICE-QM770 COM Express Module List of Figures Figure 1-1: ICE-QM770 ...................................................................................................................2 Figure 1-2: Connectors ..................................................................................................................3 Figure 1-3: ICE-QM770 Dimensions (mm) ....................................................................................
PAGE 9
ICE-QM770 COM Express Module Figure 6-12: Graphics Driver Installation Finish Screen ..........................................................85 Figure 6-13: Windows Control Panel ..........................................................................................86 Figure 6-14: System Control Panel .............................................................................................86 Figure 6-15: Device Manager List ...........................................................................
PAGE 10
ICE-QM770 COM Express Module Figure B-11: Recovery Tool Menu ........................................................................................... 116 Figure B-12: About Symantec Ghost Window ........................................................................ 117 Figure B-13: Symantec Ghost Path ......................................................................................... 117 Figure B-14: Select a Local Source Drive .....................................................................
PAGE 11
ICE-QM770 COM Express Module List of Tables Table 1-1: ICE-QM770 Specifications ...........................................................................................8 Table 2-1: Packing List.................................................................................................................12 Table 2-2: Optional Items.............................................................................................................12 Table 3-1: Peripheral Interface Connectors ...................
PAGE 12
ICE-QM770 COM Express Module BIOS Menus BIOS Menu 1: Main .......................................................................................................................41 BIOS Menu 2: Advanced ..............................................................................................................43 BIOS Menu 3: ACPI Settings .......................................................................................................43 BIOS Menu 4: RTC Wake Settings ................................
PAGE 13
ICE-QM770 COM Express Module Chapter 1 1 Introduction Page 1
PAGE 14
ICE-QM770 COM Express Module 1.1 Introduction Figure 1-1: ICE-QM770 The ICE-QM770 COM Express module provides the main processing chips and is connected to a compatible COM Express baseboard. The ICE-QM770 is equipped with the Intel® QM77 Express Chipset and Socket G2 that supports 2nd and 3rd generation Intel® Core™ i7/i5/i3, Pentium® and Celeron® processors. The COM Express standard allows the COM Express baseboard to be designed, while leaving the choice of processor till the later stages of design.
PAGE 15
ICE-QM770 COM Express Module 1.3 Connectors The connectors on the ICE-QM770 are shown in the figures below.
PAGE 16
ICE-QM770 COM Express Module 1.4 Dimensions The main dimensions of the ICE-QM770 are shown in the diagram below.
PAGE 17
ICE-QM770 COM Express Module Figure 1-4: ICE-QM770 with Heatspreader Plate and Cooloer Kit Dimensions (mm) Page 5
PAGE 18
ICE-QM770 COM Express Module 1.5 Data Flow Figure 1-5 shows the data flow between the system chipset, the CPU and other components installed on the motherboard.
PAGE 19
ICE-QM770 COM Express Module 1.6 Technical Specifications The ICE-QM770 technical specifications are listed below. Specifications/Model ICE-QM770 Form Factor PICMG COM Express R2.0 Type 6 for basic size (95 mm x 125 mm) CPU Socket Socket G2 CPU Supported Express Chipset Memory 2nd and 3rd generation Intel® Core™ i7/i5/i3, Pentium® and Celeron® processors Intel® QM77 Two 204-pin 1600/1333/1066 MHz dual-channel DDR3/DDR3L (1.35V) SO-DIMMs supported (system max.
PAGE 20
ICE-QM770 COM Express Module Specifications/Model ICE-QM770 Four USB 3.0 Eight USB 2.0 Two SATA 6Gb/s Two SATA 3Gb/s Two RS-232 HD Audio I/O Interfaces (Signal to Baseboard) 8-bit GPIO SMBus I2C LPC TPM SPI Power Consumption Operating Temperature +12V @ 1.75 A , Vcore_12V @ 3.33A (2.
PAGE 21
ICE-QM770 COM Express Module Chapter 2 2 Packing List Page 9
PAGE 22
ICE-QM770 COM Express Module 2.1 Anti-static Precautions WARNING! Static electricity can destroy certain electronics. Make sure to follow the ESD precautions to prevent damage to the product, and injury to the user. Make sure to adhere to the following guidelines: Wear an anti-static wristband: Wearing an anti-static wristband can prevent electrostatic discharge. Self-grounding: Touch a grounded conductor every few minutes to discharge any excess static buildup.
PAGE 23
ICE-QM770 COM Express Module 2.3 Packing List NOTE: If any of the components listed in the checklist below are missing, do not proceed with the installation. Contact the IEI reseller or vendor the ICE-QM770 was purchased from or contact an IEI sales representative directly by sending an email to sales@iei.com.tw.
PAGE 24
ICE-QM770 COM Express Module Quantity Item and Part Number 1 Utility CD 1 Quick Installation Guide Image Table 2-1: Packing List 2.
PAGE 25
ICE-QM770 COM Express Module Chapter 3 3 Connectors Page 13
PAGE 26
ICE-QM770 COM Express Module 3.1 Peripheral Interface Connectors This chapter details all the connectors. 3.1.1 ICE-QM770 Layout The figure below shows all the connectors.
PAGE 27
ICE-QM770 COM Express Module 3.1.2 Peripheral Interface Connectors The table below lists all the connectors on the ICE-QM770. Connector Type Label COM Express connector AB COM Express connector J3 COM Express connector CD COM Express connector J4 SO-DIMM connectors SO-DIMM connector DIMM1, DIMM2 SPI Flash (BIOS) 6-pin connector JSPI1 SPI Flash (EC) 6-pin connector JSPI2 Table 3-1: Peripheral Interface Connectors 3.
PAGE 28
ICE-QM770 COM Express Module Pin No. Description Pin No.
PAGE 29
ICE-QM770 COM Express Module Pin No. Description Pin No.
PAGE 30
ICE-QM770 COM Express Module Pin No. Description Pin No.
PAGE 31
ICE-QM770 COM Express Module Pin No. Description Pin No.
PAGE 32
ICE-QM770 COM Express Module Figure 3-3: COM Express Connector CD Location Pin No. Description Pin No.
PAGE 33
ICE-QM770 COM Express Module Pin No. Description Pin No.
PAGE 34
ICE-QM770 COM Express Module Pin No. Description Pin No.
PAGE 35
ICE-QM770 COM Express Module Pin No. Description Pin No.
PAGE 36
ICE-QM770 COM Express Module 3.2.3 SO-DIMM Connectors CN Label: DIMM1, DIMM2 CN Type: 204-pin DDR3 SO-DIMM connector CN Location: See Figure 3-4 The SO-DIMM connectors are for installing memory on the system. Figure 3-4: SO-DIMM Connector Locations 3.2.4 SPI Flash Connector (BIOS) CN Label: JSPI1 CN Type: 6-pin connector CN Location: See Figure 3-6 CN Pinouts: See Table 3-5 The SPI Flash connector is for flashing new BIOS onto the SPI BIOS chip.
PAGE 37
ICE-QM770 COM Express Module Figure 3-5: SPI Flash Connector (BIOS) Location Pin Description 1 +V3.3M_SPI_CON 2 SPI_CS 3 SPI_SO_SW 4 SPI_CLK_SW 5 SPI_SI_SW 6 GND Table 3-4: SPI Flash Connector (BIOS) Pinouts 3.2.5 SPI Flash Connector (EC) CN Label: JSPI2 CN Type: 6-pin connector CN Location: See Figure 3-6 CN Pinouts: See Table 3-5 The SPI Flash connector is for flashing new BIOS onto the embedded controller.
PAGE 38
ICE-QM770 COM Express Module Figure 3-6: SPI Flash Connector (EC) Location Pin Description 1 +V3.
PAGE 39
ICE-QM770 COM Express Module Chapter 4 4 Installation Page 27
PAGE 40
ICE-QM770 COM Express Module 4.1 Anti-static Precautions WARNING: Failure to take ESD precautions during the installation of the ICE-QM770 may result in permanent damage to the ICE-QM770 and severe injury to the user. Electrostatic discharge (ESD) can cause serious damage to electronic components, including the ICE-QM770. Dry climates are especially susceptible to ESD.
PAGE 41
ICE-QM770 COM Express Module WARNING: The installation instructions described in this manual should be carefully followed in order to prevent damage to the components and injury to the user. Before and during the installation please DO the following: Read the user manual: o The user manual provides a complete description of the ICE-QM770 installation instructions and configuration options. Wear an electrostatic discharge cuff (ESD): o Electronic components are easily damaged by ESD.
PAGE 42
ICE-QM770 COM Express Module 4.3 Socket G2 CPU Installation WARNING: CPUs are expensive and sensitive components. When installing the CPU, please be careful not to damage it in anyway. Make sure the CPU is installed properly and ensure the correct cooling kit is properly installed. To install a socket G2 CPU onto the ICE-QM770, follow the steps below: WARNING: When handling the CPU, only hold it on the sides. DO NOT touch the pins at the bottom of the CPU. Step 1: Unlock the CPU retention screw.
PAGE 43
ICE-QM770 COM Express Module Step 2: Inspect the CPU socket. Make sure there are no bent pins and make sure the socket contacts are free of foreign material. If any debris is found, remove it with compressed air. Step 3: Correctly Orientate the CPU. Make sure the IHS (integrated heat sink) side is facing upwards. Step 4: Correctly position the CPU. Match the Pin 1 mark with the cut edge on the CPU socket. See Figure 4-1. Step 5: Align the CPU pins.
PAGE 44
ICE-QM770 COM Express Module 4.4 SO-DIMM Installation WARNING: Using incorrectly specified SO-DIMM may cause permanent damage to the ICE-QM770. Please make sure the purchased SO-DIMM complies with the memory specifications of the ICE-QM770. SO-DIMM specifications compliant with the ICE-QM770 are listed in Chapter 1. To install a SO-DIMM into a SO-DIMM socket, please follow the steps below and refer to Figure 4-3. Figure 4-3: SO-DIMM Installation Step 1: Locate the SO-DIMM socket.
PAGE 45
ICE-QM770 COM Express Module 4.5 Jumper Settings 4.5.1 LVDS Panel Type Selection Jumper Label: SW1 Jumper Type: DIP switch Jumper Settings: See Table 4-1 Jumper Location: See Figure 4-4 This switch sets the resolution of the panel attached to the LVDS output.
PAGE 46
ICE-QM770 COM Express Module Figure 4-4: LVDS Panel Type Selection Switch Location 4.6 Mounting the ICE-QM770 to an Optional Baseboard NOTE: Baseboard can be designed by the end user, customized by IEI, or purchased from IEI. For more information visit the IEI website (www.ieiworld.com) or contact an IEI sales representative. WARNING: Never run the COM Express module without the cooling kit.
PAGE 47
ICE-QM770 COM Express Module Figure 4-5: Connect the COM Express Connectors Step 2: Place the supplied cooling kit on the heatspreader plate, aligning the retention screw holes (Figure 4-6). Ensure to apply thermal paste to the heat sink or heatspreader plate for optimum heat dissipation.
PAGE 48
ICE-QM770 COM Express Module Step 3: Place the heatspreader plate with the cooling kit on the ICE-QM770, aligning the retention screw holes (Figure 4-7). Step 4: Secure the heatspreader plate with the cooling kit onto the baseboard with the supplied retention screws (Figure 4-7). Figure 4-7: Secure the Heatspreader Plate with the Cooling Kit to the Baseboard Step 5: Connect the cooling kit fan cable to the CPU fan connector on the baseboard (Figure 4-8).
PAGE 49
ICE-QM770 COM Express Module Figure 4-8: Connect to the CPU Fan Connector on the Baseboard Page 37
PAGE 50
ICE-QM770 COM Express Module Chapter 5 5 BIOS Page 38
PAGE 51
ICE-QM770 COM Express Module 5.1 Introduction The BIOS is programmed onto the BIOS chip. The BIOS setup program allows changes to certain system settings. This chapter outlines the options that can be changed. 5.1.1 Starting Setup The UEFI BIOS is activated when the computer is turned on. The setup program can be activated in one of two ways. 1. Press the DEL or F2 key as soon as the system is turned on or 2. Press the DEL or F2 key when the “Press DEL or F2 to enter SETUP” message appears on the screen.
PAGE 52
ICE-QM770 COM Express Module Key Function Esc key Main Menu – Quit and not save changes into CMOS Status Page Setup Menu and Option Page Setup Menu -Exit current page and return to Main Menu F1 General help, only for Status Page Setup Menu and Option Page Setup Menu F2 Load previous values F3 Load optimized defaults F4 Save changes and Exit BIOS Table 5-1: BIOS Navigation Keys 5.1.
PAGE 53
ICE-QM770 COM Express Module 5.2 Main The Main BIOS menu (BIOS Menu 1) appears when the BIOS Setup program is entered. The Main menu gives an overview of the basic system information. Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc. Main Advanced Chipset Boot Security Save & Exit BIOS Information BIOS Vendor Core Version Compliancy Project Version Build Date and Time American Megatrends 4.6.5.3.0.18 UEFI 2.3; PI 1.2 B163AR10.
PAGE 54
ICE-QM770 COM Express Module System Overview The BIOS Information lists a brief summary of the BIOS. The fields in BIOS Information cannot be changed. The items shown in the system overview include: BIOS Information Processor Information Memory Information PCH Information SPI Clock Frequency The System Overview field also has two user configurable fields: System Date [xx/xx/xx] Use the System Date option to set the system date. Manually enter the day, month and year.
PAGE 55
ICE-QM770 COM Express Module Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc.
PAGE 56
ICE-QM770 COM Express Module ACPI Sleep State [S1 only (CPU Stop Clock)] Use the ACPI Sleep State option to specify the sleep state the system enters when it is not being used. S1 only (CPU Stop DEFAULT The system enters S1 (POS) sleep state. The system appears off. The CPU is stopped; RAM is Clock) refreshed; the system is running in a low power mode. S3 only (Suspend The caches are flushed and the CPU is powered to RAM) off. Power to the RAM is maintained.
PAGE 57
ICE-QM770 COM Express Module Wake system with Fixed Time [Disabled] Use the Wake system with Fixed Time option to enable or disable the system wake on alarm event. Disabled DEFAULT The real time clock (RTC) cannot generate a wake event Enabled If selected, the Wake up every day option appears allowing you to enable to disable the system to wake every day at the specified time.
PAGE 58
ICE-QM770 COM Express Module Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc. Advanced Configuration Security Device Support [Disable] Current Status Information NO Security Device Found Enables or Disables BIOS support for security device. O.S. will not show Security Device. TCG EFI protocol and INT1A interface will not be available. ---------------------- : Select Screen ↑ ↓: Select Item Enter: Select +/-: Change Opt.
PAGE 59
ICE-QM770 COM Express Module 5.3.4 CPU Configuration Use the CPU Configuration menu (BIOS Menu 6) to view detailed CPU specifications and configure the CPU. Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc. Advanced CPU Configuration Intel(R) Core(TM) i5-3610ME CPU @ 2.
PAGE 60
ICE-QM770 COM Express Module Intel VT-x Technology: Indicates if Intel VT-x Technology is supported by the CPU. Intel SMX Technology: Indicates if Intel SMX Technology is supported by the CPU. 64-bit: Indicates if 64-bit is supported by the CPU. L1 Data Cache: Lists the amount of data storage space on the L1 cache. L1 Code Cache: Lists the amount of code storage space on the L1 cache. L2 Cache: Lists the amount of storage space on the L2 cache. L3 Cache: Lists the amount of storage space on the L3 cache.
PAGE 61
ICE-QM770 COM Express Module 5.3.5 SATA Configuration Use the SATA Configuration menu (BIOS Menu 7) to change and/or set the configuration of the SATA devices installed in the system. Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc. Advanced SATA Mode Selection [IDE] S_ATA1 S_ATA2 S_ATA3 S_ATA4 Empty Empty Empty Empty Determines how SATA controller(s) operate. --------------------- : Select Screen ↑ ↓: Select Item Enter: Select +/-: Change Opt.
PAGE 62
ICE-QM770 COM Express Module 5.3.6 Intel(R) Rapid Start Technology Use the Intel(R) Rapid Start Technology (BIOS Menu 8) menu to configure Intel® Rapid Start Technology support. Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc. Advanced Intel(R) Rapid Start Technology [Disabled] --------------------: Select Screen ↑ ↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit Version 2.14.1219.
PAGE 63
ICE-QM770 COM Express Module 5.3.7 Intel TXT(LT) Configuration Use the Intel TXT(LT) Configuration (BIOS Menu 9) menu to configure Intel Trusted Execution Technology support. Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc. Advanced Intel Trusted Execution Technology Configuration Intel TXT support only can be enabled/disabled if SMX is enabled. VT and VT-d support must also be enabled prior to TXT.
PAGE 64
ICE-QM770 COM Express Module Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc. Advanced Intel AMT Un-Configure ME [Enabled] [Disabled] Enable/Disable Intel (R) Active Management Technology BIOS Extension. Note: iAMT H/W is always enabled. This option just controls the BIOS extension execution. If enabled, this requires additional firmware in the SPI device. --------------------: Select Screen ↑ ↓: Select Item Enter: Select +/-: Change Opt.
PAGE 65
ICE-QM770 COM Express Module 5.3.9 USB Configuration Use the USB Configuration menu (BIOS Menu 11) to read USB configuration information and configure the USB settings. Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc. Advanced USB Configuration USB Devices: 1 Keyboard Legacy USB Support [Enabled] Enables Legacy USB support. AUTO option disables legacy support if no USB devices are connected. DISABLE option will keep USB devices available only for EFI applications.
PAGE 66
ICE-QM770 COM Express Module Legacy USB support disabled Disabled Enabled DEFAULT Auto Legacy USB support enabled Legacy USB support disabled if no USB devices are connected 5.3.10 iWDD H/W Monitor The iWDD H/W Monitor menu (BIOS Menu 12) displays the CPU temperature and CPU fan speed, and contains the fan configuration submenu. Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc.
PAGE 67
ICE-QM770 COM Express Module Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc. Advanced Smart Fan Mode Configuration Smart Fan Mode Select Fan 1 Smart Fan Control Auto mode fan start temperature Auto mode fan off temperature Auto mode fan start PWM Auto mode fan slope PWM [Auto Mode] 50 40 30 1 --------------------- : Select Screen ↑ ↓: Select Item Enter Select + - Change Opt. F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save & Exit ESC Exit Version 2.14.1219.
PAGE 68
ICE-QM770 COM Express Module 5.3.11 W83627DHG Super IO Configuration Use the W83627DHG Super IO Configuration menu (BIOS Menu 14) to set or change the configurations for the serial ports. Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc.
PAGE 69
ICE-QM770 COM Express Module 5.3.11.1.1 Serial Port 1 Configuration Serial Port [Enabled] Use the Serial Port option to enable or disable the serial port. Disable the serial port Disabled Enabled DEFAULT Enable the serial port Change Settings [Auto] Use the Change Settings option to change the serial port IO port address and interrupt address. Auto DEFAULT The serial port IO port address and interrupt address are automatically detected.
PAGE 70
ICE-QM770 COM Express Module Change Settings [Auto] Use the Change Settings option to change the serial port IO port address and interrupt address. Auto DEFAULT The serial port IO port address and interrupt address are automatically detected.
PAGE 71
ICE-QM770 COM Express Module Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc. Advanced PC Health Status > Smart Fan Mode Configuration FAN1 FAN2 Smart Fan Mode Select : N/A : N/A --------------------: Select Screen ↑ ↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit Version 2.14.1219. Copyright (C) 2011 American Megatrends, Inc. BIOS Menu 16: W83627DHG H/W Monitor 5.3.12.
PAGE 72
ICE-QM770 COM Express Module Manual Mode DEFAULT The fan spins at the speed set in Fan1/Fan2 expect PWM Output settings. Fan1/ Fan2 expect PWM Output Use the + or – key to change the value. Enter a decimal number between 0 and 255. 5.3.13 Serial Port Console Redirection The Serial Port Console Redirection menu (BIOS Menu 18) allows the console redirection options to be configured.
PAGE 73
ICE-QM770 COM Express Module VT100 The target terminal type is VT100 VT100+ The target terminal type is VT100+ VT-UTF8 The target terminal type is VT-UTF8 ANSI DEFAULT The target terminal type is ANSI Bits per second [115200] Use the Bits per second option to specify the serial port transmission speed. The speed must match the other side. Long or noisy lines may require lower speeds. 9600 Sets the serial port transmission speed at 9600. 19200 Sets the serial port transmission speed at 19200.
PAGE 74
ICE-QM770 COM Express Module The parity bit is always 1. This option does not Mark provide error detection. The parity bit is always 0. This option does not Space provide error detection. Stop Bits [1] Use the Stop Bits option to specify the number of stop bits used to indicate the end of a serial data packet. Communication with slow devices may require more than 1 stop bit. 1 2 Page 62 DEFAULT Sets the number of stop bits at 1. Sets the number of stop bits at 2.
PAGE 75
ICE-QM770 COM Express Module 5.3.14 iEi Feature Use the iEi Feature menu (BIOS Menu 19) to configure One Key Recovery function. Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc. Advanced iEi Feature Auto Recovery Function [Disabled] Auto Recovery Function Reboot and recover system automatically within 10 min, when OS crashes. Please install Auto Recovery API service before enabling this function. --------------------: Select Screen ↑ ↓: Select Item Enter: Select +/-: Change Opt.
PAGE 76
ICE-QM770 COM Express Module 5.4 Chipset Use the Chipset menu (BIOS Menu 20) to access the PCH IO and System Agent (SA) configuration menus. WARNING! Setting the wrong values for the Chipset BIOS selections in the Chipset BIOS menu may cause the system to malfunction. Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc.
PAGE 77
ICE-QM770 COM Express Module Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc. Chipset PCH-IO Configuration PCI Express Configuration settings > PCI Express Configuration Azalia Restore AC Power Loss [Enabled] [Last State] --------------------: Select Screen ↑ ↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit Version 2.14.1219. Copyright (C) 2011 American Megatrends, Inc.
PAGE 78
ICE-QM770 COM Express Module 5.4.1.1 PCI Express Configuration Use the PCI Express Configuration menu (BIOS Menu 22) to select the support type of the PCI Express or PCIe Mini slots. Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc. Chipset PCI Express Configuration > > > > > > > PCIE1 Slot Settings PCIE1 Slot PCIE2 Slot PCIE3 Slot PCIE4 Slot PCIE5 Slot M_PCIE1 Slot M_PCIE2 Slot ---------------------: Select Screen ↑ ↓: Select Item Enter: Select +/-: Change Opt.
PAGE 79
ICE-QM770 COM Express Module 5.4.2 System Agent (SA) Configuration Use the System Agent (SA) Configuration menu (BIOS Menu 23) to configure the System Agent (SA) parameters. Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc. Chipset VT-d > Graphics Configuration > NB PCIe Configuration > Memory Configuration [Disabled] Check to enable VT-d function on MCH. --------------------: Select Screen ↑ ↓: Select Item Enter: Select +/-: Change Opt.
PAGE 80
ICE-QM770 COM Express Module Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc. Chipset Graphics Configuration Primary Display [Auto] DVMT Pre-Allocated DVMT Total Gfx Mem [256M] [MAX] Select which of IGFX/PEG/PCI Graphics device should be Primary Display Or select SG for Switchable Gfx. ---------------------: Select Screen ↑ ↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit Version 2.14.1219.
PAGE 81
ICE-QM770 COM Express Module DVMT Total Gfx Mem [MAX] Use the DVMT Total Gfx Mem option to select DVMT5.0 total graphic memory size used by the internal graphic device. The following options are available: 128M 256M MAX Default Primary IGFX Boot Display [VBIOS Default] Use the Primary IGFX Boot Display option to select the display device used by the system when it boots. Configuration options are listed below.
PAGE 82
ICE-QM770 COM Express Module 1680x1050 48BIT 1920x1080 48BIT 1920x1200 48BIT Backlight Control [Inverted] Use the Backlight Control option to select the backlight control mode. Inverted The LVDS backlight is brighter at high voltage level. DEFAULT The LVDS backlight is brighter at low voltage level. Normal 5.4.2.2 NB PCIe Configuration Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc.
PAGE 83
ICE-QM770 COM Express Module Enable PEG [Auto] Use the Enable PEG option to enable or disable the PCI Express controller. The following options are available: Disabled Enabled Auto Default Detect Non-Compliance Device [Disabled] Use the Detect Non-Compliance Device option to enable or disable detecting a non-compliance PCI Express device in the PEG. The following options are available: Disabled Default Enabled 5.4.2.
PAGE 84
ICE-QM770 COM Express Module 5.5 Boot Use the Boot menu (BIOS Menu 27) to configure system boot options. Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc. Main Advanced Chipset Boot Security Save & Exit Boot Configuration Bootup NumLock State Quiet Boot Option ROM Messages Launch PXE OpROM UEFI Boot [On] [Enabled] [Force BIOS] [Disabled] [Disabled] Select the keyboard NumLock state --------------------: Select Screen ↑ ↓: Select Item Boot Option Priorities Enter: Select +/-: Change Opt.
PAGE 85
ICE-QM770 COM Express Module Quiet Boot [Enabled] Use the Quiet Boot BIOS option to select the screen display when the system boots. Normal POST messages displayed Disabled Enabled DEFAULT OEM Logo displayed instead of POST messages Option ROM Messages [Force BIOS] Use the Option ROM Messages option to set the Option ROM display mode. Force DEFAULT Sets display mode to force BIOS. BIOS Sets display mode to current.
PAGE 86
ICE-QM770 COM Express Module 5.6 Security Use the Security menu (BIOS Menu 28) to set system and user passwords. Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc. Main Advanced Chipset Boot Security Save & Exit Password Description If ONLY the Administrator’s password is set, then this only limits access to Setup and is only asked for when entering Setup. If ONLY the User’s password is set, then this is a power on password and must be entered to boot or enter Setup.
PAGE 87
ICE-QM770 COM Express Module Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc. Main Advanced Chipset Boot Security Save & Exit Save Changes and Reset Discard Changes and Reset Reset the system after saving the changes. Restore Defaults Save as User Defaults Restore User Defaults --------------------: Select Screen ↑ ↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit Version 2.14.1219.
PAGE 88
ICE-QM770 COM Express Module Chapter 6 6 Software Drivers Page 76
PAGE 89
ICE-QM770 COM Express Module 6.1 Available Software Drivers NOTE: The content of the CD may vary throughout the life cycle of the product and is subject to change without prior notice. Visit the IEI website or contact technical support for the latest updates. The following drivers can be installed on the system: Chipset Graphics LAN Audio SATA (Intel® Rapid Storage Technology) USB 3.0 Intel® AMT Installation instructions are given below. 6.
PAGE 90
ICE-QM770 COM Express Module Figure 6-1: Start Up Screen Step 3: Click ICE-QM770. Step 4: The list of drivers in Figure 6-2 appears.
PAGE 91
ICE-QM770 COM Express Module 6.3 Chipset Driver Installation To install the chipset driver, please do the following. Step 1: Access the driver list. (See Section 6.2) Step 2: Click “1-Chipset”. Step 3: Locate the setup file and double click on it. Step 4: The Welcome Screen in Figure 6-3 appears. Click Next to continue. Figure 6-3: Chipset Driver Welcome Screen Step 5: The license agreement in Figure 6-4 appears. Step 6: Read the License Agreement. Step 7: Click Yes to continue.
PAGE 92
ICE-QM770 COM Express Module Figure 6-4: Chipset Driver License Agreement Step 8: The Read Me file in Figure 6-5 appears. Step 9: Click Next to continue.
PAGE 93
ICE-QM770 COM Express Module Step 10: Setup Operations are performed as shown in Figure 6-6. Figure 6-6: Chipset Driver Setup Operations Step 11: Once the Setup Operations are complete, click Next to continue. Step 12: The Finish screen in Figure 6-7 appears. Step 13: Select “Yes, I want to restart the computer now” and click the Finish icon. See Figure 6-7.
PAGE 94
ICE-QM770 COM Express Module Figure 6-7: Chipset Driver Installation Finish Screen 6.4 Graphics Driver Installation To install the graphics driver, please do the following. Step 1: Access the driver list. (See Section 6.2) Step 2: Click “2-Graphics” and select the folder which corresponds to the operating system. Step 3: Double click the setup file. Step 4: The Welcome Screen in Figure 6-8 appears. Click Next to continue.
PAGE 95
ICE-QM770 COM Express Module Figure 6-8: Graphics Driver Welcome Screen Step 5: The license agreement in Figure 6-9 appears. Read the License Agreement. Step 6: Click Yes to continue.
PAGE 96
ICE-QM770 COM Express Module Step 7: The Read Me file in Figure 6-10 appears. Step 8: Click Next to continue. Figure 6-10: Graphics Driver Read Me File Step 9: Setup Operations are performed as shown in Figure 6-11.
PAGE 97
ICE-QM770 COM Express Module Step 10: Once the Setup Operations are complete, click the Next icon to continue. Step 11: The Finish screen appears. Step 12: Select “Yes, I want to restart the computer now” and click the Finish icon. See Figure 6-12. Figure 6-12: Graphics Driver Installation Finish Screen 6.5 LAN Driver Installation To install the LAN driver, please do the following. Step 1: Right-click the Computer button from the start menu and select Properties (Figure 6-13).
PAGE 98
ICE-QM770 COM Express Module Figure 6-13: Windows Control Panel Step 2: The system control panel window in Figure 6-14 appears. Step 3: Click the Device Manager link (Figure 6-14). Figure 6-14: System Control Panel Step 4: A list of system hardware devices appears (Figure 6-15). Step 5: Right-click the Ethernet Controller that has question marks next to it (this means Windows does not recognize the device).
PAGE 99
ICE-QM770 COM Express Module Step 6: Select Update Driver Software. Figure 6-15: Device Manager List Step 7: The Update Driver Software Window appears (Figure 6-16).
PAGE 100
ICE-QM770 COM Express Module Figure 6-16: Update Driver Software Window Step 8: Select “Browse my computer for driver software” and click NEXT to continue. Step 9: Click Browse to select “X:\3-LAN” directory in the Locate File window, where “X:\” is the system CD drive. (Figure 6-17). Figure 6-17: Locate Driver Files Step 10: Click NEXT to continue.
PAGE 101
ICE-QM770 COM Express Module Step 11: Driver Installation is performed as shown in Figure 6-18. Figure 6-18: LAN Driver Installation Step 12: The Finish screen in Figure 6-19 appears. Click Close to exit.
PAGE 102
ICE-QM770 COM Express Module 6.6 Audio Driver Installation To install the Audio driver, please do the following. Step 1: Access the driver list. (See Section 6.2) Step 2: Click “4-Audio” and select the folder which corresponds to the operating system. Step 3: Double click the setup file. Step 4: The InstallShield Wizard is prepared to guide the user through the rest of the process. Step 5: Once initialized, the InstallShield Wizard welcome screen appears (Figure 6-20).
PAGE 103
ICE-QM770 COM Express Module Figure 6-21: Audio Driver Installation Step 8: When the driver installation is complete, the screen in Figure 6-22 appears.
PAGE 104
ICE-QM770 COM Express Module Step 9: Select “Yes, I want to restart my computer now” and click Finish. Step 10: The system reboots. 6.7 Intel® Rapid Storage Technology Driver Installation To install the Intel® Rapid Storage Technology driver, please do the following. Step 1: Access the driver list. (See Section 6.2) Step 2: Click “5-SATA”. Step 3: Locate the setup file and double click on it. Step 4: The Welcome Screen in Figure 6-23 appears. Step 5: Click Next to continue.
PAGE 105
ICE-QM770 COM Express Module Figure 6-24: SATA RAID Driver License Agreement Step 9: The Read Me file in Figure 6-25 appears. Step 10: Click Next to continue.
PAGE 106
ICE-QM770 COM Express Module Step 11: Setup Operations are performed as shown in Figure 6-26. Step 12: Once the Setup Operations are complete, click Next to continue. Figure 6-26: SATA RAID Driver Setup Operations Step 13: The Finish screen in Figure 6-27 appears. Step 14: Select “Yes, I want to restart this computer now” and click Finish.
PAGE 107
ICE-QM770 COM Express Module 6.8 USB 3.0 Driver Installation WARNING: Do not run this driver’s installer (Setup.exe) from a USB storage device (ie. external USB hard drive or USB thumb drive). For proper installation, please copy driver files to a local hard drive folder and run from there. To install the USB 3.0 driver, please follow the steps below. Step 1: Access the driver list. (See Section 6.2) Step 2: Click “6-USB 3.0”. Step 3: Locate the setup file and double click on it.
PAGE 108
ICE-QM770 COM Express Module Step 6: The license agreement in Figure 6-29 appears. Step 7: Read the License Agreement. Step 8: Click Yes to continue. Figure 6-29: USB 3.0 Driver License Agreement Step 9: The Read Me file in Figure 6-30 appears. Step 10: Click Next to continue. Figure 6-30: USB 3.
PAGE 109
ICE-QM770 COM Express Module Step 11: Setup Operations are performed as shown in Figure 6-31. Step 12: Once the Setup Operations are complete, click Next to continue. Figure 6-31: USB 3.0 Driver Setup Operations Step 13: The Finish screen in Figure 6-32 appears. Step 14: Select “Yes, I want to restart this computer now” and click Finish.Step 0: Figure 6-32: USB 3.
PAGE 110
ICE-QM770 COM Express Module 6.9 Intel® AMT Driver Installation The package of the Intel® AMT components includes Intel® Management Engine Interface (Intel® ME Interface) Intel® Dynamic Application Loader Intel® Identity Protection Technology (Intel® IPT) Serial Over LAN (SOL) Intel® Manageability Engine Firmware Recovery Agent Intel® Management and Security Status Local Management Service (LMS) User Notification Service (UNS) To install these Intel® AMT components, please do the following.
PAGE 111
ICE-QM770 COM Express Module Figure 6-33: Intel® ME Driver Welcome Screen Step 6: The license agreement in Figure 6-34 appears. Step 7: Read the License Agreement. Step 8: Click Yes to continue.
PAGE 112
ICE-QM770 COM Express Module Step 9: Setup Operations are performed as shown in Figure 6-35. Step 10: Once the Setup Operations are complete, click Next to continue. Figure 6-35: Intel® ME Driver Setup Operations Step 11: The Finish screen in Figure 6-36 appears. Step 12: Select “Yes, I want to restart this computer now” and click Finish.
PAGE 113
ICE-QM770 COM Express Module Appendix A A BIOS Options Page 101
PAGE 114
ICE-QM770 COM Express Module Below is a list of BIOS configuration options in the BIOS chapter. System Overview .................................................................................................................42 System Date [xx/xx/xx] ........................................................................................................42 System Time [xx:xx:xx] .......................................................................................................
PAGE 115
ICE-QM770 COM Express Module Azalia [Enabled] ...................................................................................................................65 Restore AC Power Loss [Last State] .................................................................................65 PCIE1/PCIE2/PCIE3/PCIE4/PCIE5/M_PCIE1/M_PCIE2 Slot ..............................................66 VT-d [Disabled]..................................................................................................................
PAGE 116
ICE-QM770 COM Express Module Appendix B B One Key Recovery Page 104
PAGE 117
ICE-QM770 COM Express Module B.1 One Key Recovery Introduction The IEI one key recovery is an easy-to-use front end for the Norton Ghost system backup and recovery tool. This tool provides quick and easy shortcuts for creating a backup and reverting to that backup or reverting to the factory default settings.
PAGE 118
ICE-QM770 COM Express Module After completing the five initial setup procedures as described above, users can access the recovery tool by pressing while booting up the system. The detailed information of each function is described in Section B.5. NOTE: The initial setup procedures for Linux system are described in Section B.3. 7 B.1.1 System Requirement NOTE: The recovery CD can only be used with IEI products.
PAGE 119
ICE-QM770 COM Express Module partitions. Please take the following table as a reference when calculating the size of the partition. OS OS Image after Ghost Compression Ratio Windows® 7 7 GB 5 GB 70% Windows® XPE 776 MB 560 MB 70% Windows® CE 6.0 36 MB 28 MB 77% NOTE: Specialized tools are required to change the partition size if the operating system is already installed. B.1.
PAGE 120
ICE-QM770 COM Express Module Linux o o o o o o o o o o o o o o Fedora Core 12 (Constantine) Fedora Core 11 (Leonidas) Fedora Core 10 (Cambridge) Fedora Core 8 (Werewolf) Fedora Core 7 (Moonshine) RedHat RHEL-5.4 RedHat 9 (Ghirke) Ubuntu 8.10 (Intrepid) Ubuntu 7.10 (Gutsy) Ubuntu 6.10 (Edgy) Debian 5.0 (Lenny) Debian 4.0 (Etch) SuSe 11.2 SuSe 10.3 NOTE: Installing unsupported OS versions may cause the recovery tool to fail. B.
PAGE 121
ICE-QM770 COM Express Module The detailed descriptions are described in the following sections. NOTE: The setup procedures described below are for Microsoft Windows operating system users. For Linux, most of the setup procedures are the same except for several steps described in Section B.3. 7 B.2.1 Hardware and BIOS Setup Step 1: Make sure the system is powered off and unplugged. Step 2: Install a hard drive or SSD in the system. An unformatted and unpartitioned disk is recommended.
PAGE 122
ICE-QM770 COM Express Module Step 2: Boot the system from recovery CD. When prompted, press any key to boot from the recovery CD. It will take a while to launch the recovery tool. Please be patient! Figure B-2: Launching the Recovery Tool Step 3: The recovery tool setup menu is shown as below. Figure B-3: Recovery Tool Setup Menu Step 4: Press <6> then .
PAGE 123
ICE-QM770 COM Express Module Figure B-4: Command Prompt Step 5: The command prompt window appears. Type the following commands (marked in red) to create two partitions. One is for the OS installation; the other is for saving recovery files and images which will be an invisible partition.
PAGE 124
ICE-QM770 COM Express Module Figure B-5: Partition Creation Commands Page 112
PAGE 125
ICE-QM770 COM Express Module NOTE: Use the following commands to check if the partitions were created successfully. Step 6: Press any key to exit the recovery tool and automatically reboot the system. Please continue to the following procedure: Build the Recovery Partition.Step0: B.2.3 Install Operating System, Drivers and Applications Install the operating system onto the unlabelled partition.
PAGE 126
ICE-QM770 COM Express Module B.2.4 Build-up Recovery Partition Step 1: Put the recover CD in the optical drive. Step 2: Start the system. Step 3: Boot the system from the recovery CD. When prompted, press any key to boot from the recovery CD. It will take a while to launch the recovery tool. Please be patient! Figure B-6: Launching the Recovery Tool Step 4: When the recovery tool setup menu appears, press <2> then .
PAGE 127
ICE-QM770 COM Express Module Step 5: The Symantec Ghost window appears and starts configuring the system to build a recovery partition. In this process the partition created for recovery files in Section B.2.2 is hidden and the recovery tool is saved in this partition. 7 Figure B-8: Building the Recovery Partition Step 6: After completing the system configuration, press any key in the following window to reboot the system. Figure B-9: Press Any Key to Continue Step 7: Eject the recovery CD.
PAGE 128
ICE-QM770 COM Express Module B.2.5 Create Factory Default Image NOTE: Before creating the factory default image, please configure the system to a factory default environment, including driver and application installations. To create a factory default image, please follow the steps below. Step 1: Turn on the system. When the following screen displays (Figure B-10), press 7 the key to access the recovery tool.
PAGE 129
ICE-QM770 COM Express Module Figure B-12: About Symantec Ghost Window Step 4: Use mouse to navigate to the option shown below (Figure B-13). 7 Figure B-13: Symantec Ghost Path Step 5: Select the local source drive (Drive 1) as shown in Figure B-14. Then click OK.
PAGE 130
ICE-QM770 COM Express Module Figure B-14: Select a Local Source Drive Step 6: Select a source partition (Part 1) from basic drive as shown in Figure B-15. 7 Then click OK. Figure B-15: Select a Source Partition from Basic Drive Step 7: Select 1.2: [Recovery] NTFS drive and enter a file name called iei (Figure B-16). Click Save. The factory default image will then be saved in the 7 selected recovery drive and named IEI.GHO. WARNING: The file name of the factory default image must be iei.GHO.
PAGE 131
ICE-QM770 COM Express Module Figure B-16: File Name to Copy Image to Step 8: When the Compress Image screen in Figure B-17 prompts, click High to make 7 the image file smaller.
PAGE 132
ICE-QM770 COM Express Module Step 9: The Proceed with partition image creation window appears, click Yes to continue. Figure B-18: Image Creation Confirmation Step 10: The Symantec Ghost starts to create the factory default image (Figure B-19). 7 Figure B-19: Image Creation Complete Step 11: When the image creation completes, a screen prompts as shown in Figure B-20. 7 Click Continue and close the Ghost window to exit the program.
PAGE 133
ICE-QM770 COM Express Module Step 12: The recovery tool main menu window is shown as below. Press any key to reboot the system. Step0: Figure B-21: Press Any Key to Continue B.3 Auto Recovery Setup Procedure The auto recovery function allows a system to automatically restore from the factory default image after encountering a Blue Screen of Death (BSoD) or a hang for around 10 minutes. To use the auto recovery function, follow the steps described in the following sections.
PAGE 134
ICE-QM770 COM Express Module Step 1: Follow the steps described in Section B.2.1 ~ Section B.2.3 to setup BIOS, create partitions and install operating system. Step 2: Install the auto recovery utility into the system by double clicking the Utility/AUTORECOVERY-SETUP.exe in the One Key Recovery CD. This utility MUST be installed in the system, otherwise, the system will automatically restore from the factory default image every ten (10) minutes.
PAGE 135
ICE-QM770 COM Express Module Step 4: Reboot the system from the recovery CD. When prompted, press any key to boot from the recovery CD. It will take a while to launch the recovery tool. Please be patient! Figure B-24: Launching the Recovery Tool Step 5: When the recovery tool setup menu appears, press <4> then . Figure B-25: Auto Recovery Environment for Windows Step 6: The Symantec Ghost window appears and starts configuring the system to build an auto recovery partition.
PAGE 136
ICE-QM770 COM Express Module Figure B-26: Building the Auto Recovery Partition Step 7: After completing the system configuration, the following message prompts to confirm whether to create a factory default image. Type Y to have the system create a factory default image automatically. Type N within 6 seconds to skip this process (The default option is YES). It is suggested to choose YES for this option.
PAGE 137
ICE-QM770 COM Express Module Step 8: The Symantec Ghost starts to create the factory default image (Figure B-28). Figure B-28: Image Creation Complete Step 9: After completing the system configuration, press any key in the following window to restart the system. Figure B-29: Press any key to continue Step 10: Eject the One Key Recovery CD and restart the system. Step 11: Press the key as soon as the system is turned on to enter the BIOS.
PAGE 138
ICE-QM770 COM Express Module Main Advanced PCIPNP BIOS SETUP UTILITY Boot Security Chipset Exit iEi Feature ⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯ Auto Recovery Function [Enabled] Recover from PXE [Disabled] ↑ ↓ Enter F1 F10 ESC Select Screen Select Item Go to SubScreen General Help Save and Exit Exit v02.61 ©Copyright 1985-2006, American Megatrends, Inc. Figure B-30: IEI Feature Step 13: Save changes and restart the system.
PAGE 139
ICE-QM770 COM Express Module Partition 1: / Partition 2: SWAP NOTE: Please reserve enough space for partition 3 for saving recovery images. Figure B-31: Partitions for Linux Step 3: Create a recovery partition. Insert the recovery CD into the optical disk drive. Follow Step 1 ~ Step 3 described in Section B.2.2. Then type the following 7 commands (marked in red) to create a partition for recovery images.
PAGE 140
ICE-QM770 COM Express Module recovery partition. After completing the system configuration, press any key to reboot the system. Eject the recovery CD. Figure B-32: System Configuration for Linux Step 5: Access the recovery tool main menu by modifying the “menu.lst”. To first access the recovery tool main menu, the menu.lst must be modified. In Linux, enter Administrator (root). When prompt appears, type: cd /boot/grub vi menu.lst Figure B-33: Access menu.lst in Linux (Text Mode) Step 6: Modify the menu.
PAGE 141
ICE-QM770 COM Express Module Step 7: The recovery tool menu appears. (Figure B-34) 7 Figure B-34: Recovery Tool Menu Step 8: Create a factory default image. Follow Step 2 ~ Step 12 described in Section B.2.5 to create a factory default image. 7 B.5 Recovery Tool Functions After completing the initial setup procedures as described above, users can access the recovery tool by pressing while booting up the system. However, if the setup procedure in Section B.
PAGE 142
ICE-QM770 COM Express Module Figure B-35: Recovery Tool Main Menu The recovery tool has several functions including: 1. Factory Restore: Restore the factory default image (iei.GHO) created in Section B.2.5. 7 2. Backup system: Create a system backup image (iei_user.GHO) which will be saved in the hidden partition. 3. Restore your last backup: Restore the last system backup image 4. Manual: Enter the Symantec Ghost window to configure manually. 5. Quit: Exit the recovery tool and restart the system.
PAGE 143
ICE-QM770 COM Express Module B.5.1 Factory Restore To restore the factory default image, please follow the steps below. Step 1: Type <1> and press in the main menu. Step 2: The Symantec Ghost window appears and starts to restore the factory default. A factory default image called iei.GHO is created in the hidden Recovery partition. Figure B-36: Restore Factory Default Step 3: The screen is shown in Figure B-37 appears when completed. Press any key to 7 reboot the system.
PAGE 144
ICE-QM770 COM Express Module B.5.2 Backup System To backup the system, please follow the steps below. Step 1: Type <2> and press in the main menu. Step 2: The Symantec Ghost window appears and starts to backup the system. A backup image called iei_user.GHO is created in the hidden Recovery partition. Figure B-38: Backup System Step 3: The screen is shown in Figure B-39 appears when system backup is complete. 7 Press any key to reboot the system.
PAGE 145
ICE-QM770 COM Express Module B.5.3 Restore Your Last Backup To restore the last system backup, please follow the steps below. Step 1: Type <3> and press in the main menu. Step 2: The Symantec Ghost window appears and starts to restore the last backup image (iei_user.GHO). Figure B-40: Restore Backup Step 3: The screen shown in Figure B-41 appears when backup recovery is complete. 7 Press any key to reboot the system.
PAGE 146
ICE-QM770 COM Express Module B.5.4 Manual To restore the last system backup, please follow the steps below. Step 1: Type <4> and press in the main menu. Step 2: The Symantec Ghost window appears. Use the Ghost program to backup or recover the system manually. Figure B-42: Symantec Ghost Window Step 3: When backup or recovery is completed, press any key to reboot the system.
PAGE 147
ICE-QM770 COM Express Module B.6 Restore Systems from a Linux Server through LAN The One Key Recovery allows a client system to automatically restore to a factory default image saved in a Linux system (the server) through LAN connectivity after encountering a Blue Screen of Death (BSoD) or a hang for around 10 minutes. To be able to use this function, the client system and the Linux system MUST reside in the same domain.
PAGE 148
ICE-QM770 COM Express Module B.6.1 Configure DHCP Server Settings Step 1: Install the DHCP #yum install dhcp (CentOS, commands marked in red) #apt-get install dhcp3-server (Debian, commands marked in blue) Step 2: Confirm the operating system default settings: dhcpd.conf. CentOS Use the following command to show the DHCP server sample location: #vi /etc/dhcpd.conf The DHCP server sample location is shown as below: Use the following command to copy the DHCP server sample to etc/dhcpd.
PAGE 149
ICE-QM770 COM Express Module filename “pxelinux.0”; B.6.2 Configure TFTP Settings Step 1: Install the tftp, httpd and syslinux. #yum install tftp-server httpd syslinux (CentOS) #apt-get install tftpd-hpa xinetd syslinux (Debian) Step 2: Enable the TFTP server by editing the “/etc/xinetd.d/tftp” file and make it use the remap file. The “-vvv” is optional but it could definitely help on getting more information while running the remap file. For example: CentOS #vi /etc/xinetd.
PAGE 150
ICE-QM770 COM Express Module Debian Replace the TFTP settings from “inetd” to “xinetd” and annotate the “inetd” by adding “#”. #vi /etc/inetd.conf Modify: #tftp dgram udp wait root /usr/sbin....... (as shown below) #vi /etc/xinetd.d/tftp B.6.3 Configure One Key Recovery Server Settings Step 1: Copy the Utility/RECOVERYR10.TAR.BZ2 package from the One Key Recovery CD to the system (server side). Step 2: Extract the recovery package to /. #cp RecoveryR10.tar.bz2 / #cd / #tar –xvjf RecoveryR10.tar.
PAGE 151
ICE-QM770 COM Express Module B.6.4 Start the DHCP, TFTP and HTTP Start the DHCP, TFTP and HTTP. For example: CentOS #service xinetd restart #service httpd restart #service dhcpd restart Debian #/etc/init.d/xinetd reload #/etc/init.d/xinetd restart #/etc/init.d/dhcp3-server restart B.6.5 Create Shared Directory Step 1: Install the samba. #yum install samba Step 2: Create a shared directory for the factory default image. #mkdir /share #cd /share #mkdir /image #cp iei.
PAGE 152
ICE-QM770 COM Express Module Modify: [image] comment = One Key Recovery path = /share/image browseable = yes writable = yes public = yes create mask = 0644 directory mask = 0755 Step 4: Edit “/etc/samba/smb.conf” for your environment. For example: Step 5: Modify the hostname #vi /etc/hostname Modify: RecoveryServer B.6.6 Setup a Client System for Auto Recovery Step 1: Disable the automatically restart function before creating the factory default image. Go to: My Computer Properties Advanced.
PAGE 153
ICE-QM770 COM Express Module Figure B-43: Disable Automatically Restart Step 2: Configure the following BIOS options of the client system. Advanced → iEi Feature → Auto Recovery Function → Enabled Advanced → iEi Feature → Recover from PXE → Enabled Boot → Launch PXE OpROM → Enabled Step 3: Continue to configure the Boot Option Priorities BIOS option of the client system: Boot Option #1 remain the default setting to boot from the original OS. Boot Option #2 select the boot from LAN option.
PAGE 154
ICE-QM770 COM Express Module MUST be installed in the system, otherwise, the system will automatically restore from the factory default image every ten (10) minutes. Step 6: Restart the client system from LAN. If the system encounters a Blue Screen of Death (BSoD) or a hang for around 10 minutes, it will automatically restore from the factory default image. The following screens will show when the system starts auto recovering.
PAGE 155
ICE-QM770 COM Express Module NOTE: A firewall or a SELinux is not in use in the whole setup process described above. If there is a firewall or a SELinux protecting the system, modify the configuration information to accommodate them. B.7 Other Information B.7.1 Using AHCI Mode or ALi M5283 / VIA VT6421A Controller When the system uses AHCI mode or some specific SATA controllers such as ALi M5283 or VIA VT6421A, the SATA RAID/AHCI driver must be installed before using one key recovery.
PAGE 156
ICE-QM770 COM Express Module Step 5: When the following window appears, press ~~to select “Specify Additional Device”.~~
~~PAGE 157~~
ICE-QM770 COM Express Module Step 6: In the following window, select a SATA controller mode used in the system. Then press . The user can now start using the SATA HDD. Step 7: After pressing , the system will get into the recovery tool setup menu. Continue to follow the setup procedure from Step 4 in Section B.2.2 Create 7 Partitions to finish the whole setup process. B.7.
~~PAGE 158~~
~~ICE-QM770 COM Express Module Appendix C C Terminology Page 146~~
~~PAGE 159~~
ICE-QM770 COM Express Module AC ’97 Audio Codec 97 (AC’97) refers to a codec standard developed by Intel® in 1997. ACPI Advanced Configuration and Power Interface (ACPI) is an OS-directed configuration, power management, and thermal management interface. AHCI Advanced Host Controller Interface (AHCI) is a SATA Host controller register-level interface. ATA The Advanced Technology Attachment (ATA) interface connects storage devices including hard disks and CD-ROM drives to a computer.
~~PAGE 160~~
ICE-QM770 COM Express Module DIMM Dual Inline Memory Modules are a type of RAM that offer a 64-bit data bus and have separate electrical contacts on each side of the module. DIO The digital inputs and digital outputs are general control signals that control the on/off circuit of external devices or TTL devices. Data can be read or written to the selected address to enable the DIO functions.
~~PAGE 161~~
ICE-QM770 COM Express Module LVDS Low-voltage differential signaling (LVDS) is a dual-wire, high-speed differential electrical signaling system commonly used to connect LCD displays to a computer. POST The Power-on Self Test (POST) is the pre-boot actions the system performs when the system is turned-on. RAM Random Access Memory (RAM) is volatile memory that loses data when power is lost. RAM has very fast data transfer rates compared to other storage like hard drives.
~~PAGE 162~~
~~ICE-QM770 COM Express Module Appendix D D Watchdog Timer Page 150~~
~~PAGE 163~~
ICE-QM770 COM Express Module NOTE: The following discussion applies to DOS environment. Contact IEI support or visit the IEI website for specific drivers for other operating systems. The Watchdog Timer is provided to ensure that standalone systems can always recover from catastrophic conditions that cause the CPU to crash. This condition may have occurred by external EMIs or a software bug.
~~PAGE 164~~
~~ICE-QM770 COM Express Module NOTE: When exiting a program it is necessary to disable the Watchdog Timer, otherwise the system resets.~~
~~PAGE 165~~
~~ICE-QM770 COM Express Module Appendix E E Hazardous Materials Disclosure Page 153~~
~~PAGE 166~~
ICE-QM770 COM Express Module E.1 Hazardous Materials Disclosure Table for IPB Products Certified as RoHS Compliant Under 2002/95/EC Without Mercury The details provided in this appendix are to ensure that the product is compliant with the Peoples Republic of China (China) RoHS standards. The table below acknowledges the presences of small quantities of certain materials in the product, and is applicable to China RoHS only.
~~PAGE 167~~
ICE-QM770 COM Express Module Part Name Toxic or Hazardous Substances and Elements Lead Mercury Cadmium Hexavalent Polybrominated Polybrominated (Pb) (Hg) (Cd) Chromium Biphenyls Diphenyl (CR(VI)) (PBB) Ethers (PBDE) Housing X O O O O X Display X O O O O X Printed Circuit X O O O O X X O O O O O X O O O O X Fan Assembly X O O O O X Power Supply X O O O O X O O O O O O Board Metal Fasteners Cable Assembly Assemblies Battery O: This toxic o
~~PAGE 168~~
ICE-QM770 COM Express Module 此附件旨在确保本产品符合中国 RoHS 标准。以下表格标示此产品中某有毒物质的含量符合中国 RoHS 标准规定的限量要求。本产品上会附有”环境友好使用期限”的标签，此期限是估算这些物质”不会有泄漏或突变”的年限。本产品可能包含有较短的环境友好使用期限的可替换元件，像是电池或灯管，这些元件将会单独标示出来。部件名称有毒有害物质或元素铅汞镉六价铬多溴联苯多溴二苯 (Pb) (Hg) (Cd) (CR(VI)) (PBB) 醚 (PBDE) 壳体 X O O O O X 显示 X O O O O X 印刷电路板 X O O O O X 金属螺帽 X O O O O O 电缆组装 X O O O O X 风扇组装 X O O O O X 电力供应组装 X O O O O X 电池 O O O O O O O: 表示该有毒有害物质在该部件所有物质材料中的含量均在 SJ/T11363-2006 标准规定