AVL-2000PLUS Auto Data Server IEI Technology Corp. MODEL: AVL-2000PLUS Auto Data Server with Intel® Atom™ CPU, Gigabit Ethernet, OBD-II, USB, GPS, Wi-Fi, Bluetooth, Video Capture, Audio, RS-232/422/485, RoHS Compliant User Manual Page 1 Rev. 1.
AVL-2000PLUS Auto Data Server Revision Date Version Changes 28 June, 2011 1.
AVL-2000PLUS Auto Data Server Copyright COPYRIGHT NOTICE The information in this document is subject to change without prior notice in order to improve reliability, design and function and does not represent a commitment on the part of the manufacturer. In no event will the manufacturer be liable for direct, indirect, special, incidental, or consequential damages arising out of the use or inability to use the product or documentation, even if advised of the possibility of such damages.
AVL-2000PLUS Auto Data Server Table of Contents 1 INTRODUCTION.......................................................................................................... 8 1.1 OVERVIEW.................................................................................................................. 9 1.2 FEATURES ................................................................................................................... 9 1.3 FRONT PANEL ................................................................
AVL-2000PLUS Auto Data Server 3.7 POWER-ON PROCEDURE ........................................................ 錯誤! 尚未定義書籤。 尚未定義書籤。 3.7.1 Installation Checklist .................................................... 錯誤! 尚未定義書籤 尚未定義書籤。 。 3.7.2 Power-on Procedure ..................................................... 錯誤! 尚未定義書籤 尚未定義書籤。 。 3.7.3 Power State ................................................................... 錯誤! 尚未定義書籤 尚未定義書籤。 。 3.8 SYSTEM MAINTENANCE .................................................
AVL-2000PLUS Auto Data Server List of Figures Figure 1-1: AVL-2000PLUS Auto Data Server ..........................................................................9 Figure 1-2: Front Panel ........................................................................................................... 10 Figure 1-3: LED Indicators ...................................................................................................... 11 Figure 1-4: Rear View .........................................................
AVL-2000PLUS Auto Data Server List of Tables Table 1-1: Technical Specifications........................................................................................ 14 Table 2-1: Packing List............................................................................................................ 18 Table 2-2: Optional Items ........................................................................................................ 18 Table 3-1: Digital I/O Connector Pinouts .............................
AVL-2000PLUS Auto Data Server Chapter 1 1 Introduction Page 8
AVL-2000PLUS Auto Data Server 1.1 Overview Figure 1-1: AVL-2000PLUS Auto Data Server The AVL-2000PLUS is an embedded system for indoor only. At the heart of the system is the Intel® Atom™ processor, offering low power in a powerful package. The chipset is rounded off with the Intel® US15WP. The system also offers HSUPA/GPRS/GSM connection, Global Position System (GPS) and On-Board Diagnostic System (OBD) technology.
AVL-2000PLUS Auto Data Server GPS system Optional UHF RFID reader module Supports OBD-II/FMS/J1939 RoHS compliance 1.3 Front Panel The following are found on the front panel.
AVL-2000PLUS Auto Data Server 1.3.1 LED Indicators The LED indicators on the front panel show the status of UHF RFID, Wi-Fi/Bluetooth, RS-422/485, GPRS/HSUPA connection as well as CF card and battery activity. Figure 1-3: LED Indicators 1.4 Rear Panel The rear panel has VESA mounting screw holes for DIN rail mounting.
AVL-2000PLUS Auto Data Server 1.5 Right Panel The right panel has one remote control connector, one digital I/O connector and one 12 V DC power connector. The ACC/DC power switch is also located on the right panel. Figure 1-5: Right Panel 1.6 Left Panel The left panel provide access to the SD card slot, SIM card slot and CF card slot. These slots are protected by a cover. After inset the SD card slot, SIM card slot or CF card shell be closed the cover with screw before operation.
AVL-2000PLUS Auto Data Server 1.7 System Specifications The technical specifications for the AVL-2000PLUS systems are listed in Table 1-1. System CPU 1.1 GHz Intel® Atom™ Z510 Chipset Intel® US15WP Memory One 1.0 GB 533 MHz DDR2 pre-installed OS Windows 7 Embedded Storage 1 x 4 GB CompactFlash® card (500x) preinstalled 1 x SD card slot Audio Realtek ALC888 Digital I/O 4 inputs / 4 outputs Communication LAN 1 x 10/100/1000 Mbps RJ-45 Wireless LAN 802.11b/g Bluetooth Bluetooth 2.
AVL-2000PLUS Auto Data Server Connectors and Buttons Antenna Connectors 1 x GPS antenna connector 1 x 2.5G/3G/3.
AVL-2000PLUS Auto Data Server 1.8 Dimensions The dimensions are shown below.
AVL-2000PLUS Auto Data Server Chapter 2 2 Unpacking Page 16
AVL-2000PLUS Auto Data Server To unpack the AVL-2000PLUS, follow the steps below: Step 1: Use box cutters, a knife or a sharp pair of scissors that seals the top side of the external (second) box. Step 2: Open the external (second) box. Step 3: Use box cutters, a knife or a sharp pair of scissors that seals the top side of the internal (first) box. Step 4: Lift the monitor out of the boxes. Step 5: Remove both polystyrene ends, one from each side. Step 6: Pull the plastic cover off the AVL-2000PLUS.
AVL-2000PLUS Auto Data Server Quantity Item 1 GPS/GSM antenna Image (P/N: 32506-000100-100-RS) 1 Wi-Fi/Bluetooth antenna (P/N: 32505-000400-100-RS) 1 OBD-II cable (P/N: 32025-000300-100-RS) 1 J1939/FMS cable (P/N: 32025-000400-100-RS) 1 User manual CD and driver CD Table 2-1: Packing List Item UHF RFID antenna with cable Table 2-2: Optional Items Page 18 Image
AVL-2000PLUS Auto Data Server If any of these items are missing or damaged, contact the distributor or sales representative immediately.
AVL-2000PLUS Auto Data Server Chapter 3 3 Installation Page 20
AVL-2000PLUS Auto Data Server 3.1 Anti-static Precautions WARNING: Failure to take ESD precautions during the maintenance of the AVL-2000PLUS may result in permanent damage to the AVL-2000PLUS and severe injury to the user. Electrostatic discharge (ESD) can cause serious damage to electronic components, including the AVL-2000PLUS. Dry climates are especially susceptible to ESD.
AVL-2000PLUS Auto Data Server Anti-static Discharge: If a user open the bottom panel of the AVL-2000PLUS, to configure the jumpers or plug in added peripheral devices, ground themselves first and wear and anti-static wristband. 3.3 Installation and Configuration Steps The following installation steps must be followed. Step 1: Unpack the system Step 2: Install a SIM card or SD card (optional) Step 3: Connect peripheral devices Step 4: Mount the system Step 5: Power up the system Step 0: 3.
AVL-2000PLUS Auto Data Server Step 2: Locate the SIM card slot or SD card slot. See Figure 3-2. Figure 3-2: Slot Locations Step 3: Insert the card into the correspondent slot.Step 0: 3.5 Mounting the System To mount the system onto a VESA bracket, please follow the steps below. Step 1: Attach theVESA mounting bracket to the bottom panel of the AVL-2000PLUS. Secure the bracket to the AVL-2000PLUS with the supplied retention screws ( Figure 3-3).
AVL-2000PLUS Auto Data Server 3.6 I/O Interface Connectors This section provides an overview of the I/O interface connectors of the AVL-2000PLUS. 3.6.1 CAN Bus Connection There is one 3-pin CAN Bus connector. The connector pinouts are shown in Figure 3-4: CAN Bus Connector Pinouts 3.6.2 Digital I/O Connection The AVL-2000PLUS right side panel has one 14-pin wafer connector for digital I/O connection. The pinouts for digital I/O connector are listed in the table below.
AVL-2000PLUS Auto Data Server 13 SPEED_IN+ 14 SPEED_IN- Table 3-1: Digital I/O Connector Pinouts 3.6.3 LAN Connection There is one external RJ-45 LAN connector. The RJ-45 connector enables connection to an external network. To connect a LAN cable with an RJ-45 connector, please follow the instructions below. Step 1: Locate the RJ-45 connectors on the bottom panel of the AVL-2000PLUS. Step 2: Align the connectors.
AVL-2000PLUS Auto Data Server 3.6.4 OBD-II Connector The AVL-2000PLUS has one DB-9 male connector for OBD-II connection. Use the OBD-II cable or J1939/FMS cable (Figure 3-7) in the package to connect the AVL-2000PLUS. OBD-II Cable J1939/FMS Cable Figure 3-7: OBD-II Cable and J1939/FMS Cable The pinouts for OBD-II connector are listed in the table below.
AVL-2000PLUS Auto Data Server The pinout locations of OBD-II cable connector and J1939/FMS cable connector are shown below. Figure 3-9: OBD-II Connector Pinouts Figure 3-10: J1939/FMS Connector Pinouts 3.6.5 Power Input Connection The AVL-2000PLUS has one 12 V DC input connector on the right panel.
AVL-2000PLUS Auto Data Server 3.6.6 Remote Control Connection The AVL-2000PLUS right side panel has one 14-pin wafer connector for the optional remote control connection. The pinouts for remote control connector are listed in the table below. Figure 3-12: Remote Control Connector Pinouts Location PIN NO. DESCRIPTION PIN NO. DESCRIPTION 1 PWR_BTN 2 GND 3 FU1 4 GND 5 FU2 6 GND 7 FU3 8 GND 9 PW_BAT_LED# 10 GND 11 HDD_LED 12 3.
AVL-2000PLUS Auto Data Server Step 3: Insert the serial connector. Insert the DB-9 connector of a serial device into the DB-9 connector on the cable. See Figure 3-13. Figure 3-13: Serial Device Connector Step 4: Secure the connector. Secure the serial device connector to the external interface by tightening the two retention screws on either side of the connector. 3.6.7.1 COM1 Pinouts The COM1 connector can be set as RS-232 (default), RS-422 or RS-485 in BIOS.
AVL-2000PLUS Auto Data Server 3.6.8 USB Device Connection There are two external USB connectors. To connect a USB device, please follow the instructions below. Step 1: Located the USB connectors. The locations of the USB connectors are shown in Chapter 2. Step 2: Align the connectors. Align the USB device connector with one of the connectors on the bottom panel. Figure 3-14: USB Device Connection Step 3: Insert the device connector.
AVL-2000PLUS Auto Data Server Figure 3-15: Video Capture Cable The pinouts for video connector are listed in the table below. Figure 3-16: Video Connector Pinouts Location Pin Description 1 CN1_A 2 CN1_B 3 CN1_C 4 CN1_D 5 SIN1_A 6 GND 7 GND 8 GND 9 GND Table 3-5: Video Connector Pinouts 3.6.10 VGA Monitor Connection The AVL-2000PLUS has a single female DB-15 connector on the external peripheral interface panel. The DB-15 connector is connected to a CRT or VGA monitor.
AVL-2000PLUS Auto Data Server Step 1: Locate the female DB-15 connector. The location of the female DB-15 connector is shown in Chapter 3. Step 2: Align the VGA connector. Align the male DB-15 connector on the VGA screen cable with the female DB-15 connector on the external peripheral interface. Step 3: Insert the VGA connector. Once the connectors are properly aligned with the insert the male connector from the VGA screen into the female connector on the AVL-2000PLUS. See Figure 3-17.
AVL-2000PLUS Auto Data Server NOTE: A user cannot replace a motherboard. If the motherboard fails it must be shipped back to IEI to be replaced. Please contact the system vendor, reseller or an IEI sales person directly. Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
AVL-2000PLUS Auto Data Server Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
