User guide

ManualsBrandsIEI Integration ManualsHardwareKINO-9453 v2.00

KINO-9453 Mini-ITX Motherboard

Page I

KINO-9453 Motherboard User Manual

Summary of content (229 pages)

PAGE 1
KINO-9453 Mini-ITX Motherboard KINO-9453 Motherboard User Manual Page I
PAGE 2
KINO-9453 Mini-ITX Motherboard Revision Date Version Changes 2008-07 v2.00 -Changed Northbridge chipset from Intel® 945GM to Intel® 945GME -Added system fan connector (SYS_FAN1) information -Added three jumper information: AT/ATX power mode select jumpers LVDS screen resolution select jumper COM3 mode select jumpers RS-422/485 terminal resister jumpers 2007-04 Page II v1.
PAGE 3
KINO-9453 Mini-ITX Motherboard Copyright COPYRIGHT NOTICE The information in this document is subject to change without prior notice in order to improve reliability, design and function and does not represent a commitment on the part of the manufacturer. In no event will the manufacturer be liable for direct, indirect, special, incidental, or consequential damages arising out of the use or inability to use the product or documentation, even if advised of the possibility of such damages.
PAGE 4
KINO-9453 Mini-ITX Motherboard Manual Conventions WARNING! Warnings appear where overlooked details may cause damage to the equipment or result in personal injury. Warnings should be taken seriously. Warnings are easy to recognize. The word “warning” is written as “WARNING,” both capitalized and bold and is followed by text. The text is the warning message. A warning message is shown below: WARNING: This is an example of a warning message.
PAGE 5
KINO-9453 Mini-ITX Motherboard CAUTION: This is an example of a caution message. Failure to adhere to cautions messages may result in permanent damage to the KINO-9453. Please take caution messages seriously. NOTE: These messages inform the reader of essential but non-critical information. These messages should be read carefully as any directions or instructions contained therein can help avoid making mistakes. Notes are easy to recognize.
PAGE 6
KINO-9453 Mini-ITX Motherboard Packing List NOTE: If any of the components listed in the checklist below are missing, please do not proceed with the installation. Contact the IEI reseller or vendor you purchased the KINO-9453 from or contact an IEI sales representative directly. To contact an IEI sales representative, please send an email to sales@iei.com.tw. The items listed below should all be included in the KINO-9453 package.
PAGE 7
KINO-9453 Mini-ITX Motherboard Table of Contents 1 INTRODUCTION..................................................................................................... 1 1.1 INTRODUCTION .......................................................................................................... 2 1.1.1 KINO-9453 Benefits........................................................................................... 3 1.1.2 KINO-9453 Features...........................................................................
PAGE 8
KINO-9453 Mini-ITX Motherboard 2.6.5 Intel® ICH7-M PCI Interface........................................................................... 18 2.6.6 Intel® ICH7-M Real Time Clock ...................................................................... 18 2.6.7 Intel® ICH7-M SATA Controller ...................................................................... 18 2.6.8 Intel® ICH7-M USB Controller........................................................................ 18 2.7 PCIE BUS COMPONENTS ...............
PAGE 9
KINO-9453 Mini-ITX Motherboard 4.2.1 Fan Connectors................................................................................................ 32 4.2.2 Front Panel Connector .................................................................................... 33 4.2.3 Digital Input/Output Connector....................................................................... 34 4.2.4 IDE Connector ................................................................................................. 35 4.2.
PAGE 10
KINO-9453 Mini-ITX Motherboard 5.4.4 RS-422 or RS-486 Termination Resister .......................................................... 70 5.4.5 LVDS Screen Resolution Selection................................................................... 71 5.4.6 LVDS Voltage Selection.................................................................................... 73 5.5 CHASSIS INSTALLATION ........................................................................................... 75 5.5.1 Airflow.................
PAGE 11
KINO-9453 Mini-ITX Motherboard 6.3.6 APM Configuration......................................................................................... 111 6.3.7 Remote Access Configuration .........................................................................113 6.3.8 USB Configuration..........................................................................................117 6.3.8.1 USB Mass Storage Device Configuration............................................... 120 6.4 PCI/PNP ...........................
PAGE 12
KINO-9453 Mini-ITX Motherboard B.3.1 Enable the DIO Input Function..................................................................... 186 B.3.2 Enable the DIO Output Function .................................................................. 186 C WATCHDOG TIMER .......................................................................................... 187 D ADDRESS MAPPING.......................................................................................... 190 D.1 ADDRESS MAP .....................
PAGE 13
KINO-9453 Mini-ITX Motherboard List of Figures Figure 1-1: KINO-9453 Embedded SBC ........................................................................................2 Figure 1-2: KINO-9453 Overview ...................................................................................................4 Figure 2-1: KINO-9453 Dimensions (mm).....................................................................................9 Figure 2-2: External Interface Panel Dimensions (mm) ..............................
PAGE 14
KINO-9453 Mini-ITX Motherboard Figure 5-5: Connect the cooling fan cable.................................................................................63 Figure 5-6: Installing a DIMM .......................................................................................................64 Figure 5-7: Jumper Locations .....................................................................................................65 Figure 5-8: AT/ATX Power Select Jumper Location .......................................
PAGE 15
KINO-9453 Mini-ITX Motherboard Figure 7-16: Double Click the System Icon............................................................................. 159 Figure 7-17: Double Click the Device Manager Tab ............................................................... 159 Figure 7-18: Device Manager List ............................................................................................ 160 Figure 7-19: Search for Suitable Driver .......................................................................
PAGE 16
KINO-9453 Mini-ITX Motherboard List of Tables Table 1-1: Technical Specifications ..............................................................................................7 Table 2-1: Processor Features ....................................................................................................12 Table 2-2: Supported Processors ...............................................................................................13 Table 2-3: Supported HDD Specifications...............................
PAGE 17
KINO-9453 Mini-ITX Motherboard Table 5-1: Jumpers .......................................................................................................................66 Table 5-2: AT/ATX Power Select Jumper Settings .....................................................................66 Table 5-3: Clear CMOS Jumper Settings ....................................................................................68 Table 5-4: COM 3 Function Select Jumper Settings ...............................................
PAGE 18
KINO-9453 Mini-ITX Motherboard BIOS Menus Menu 1: Main .................................................................................................................................90 Menu 2: Advanced ........................................................................................................................92 Menu 3: CPU Configuration.........................................................................................................93 Menu 4: IDE Configuration .........................
PAGE 19
KINO-9453 Mini-ITX Motherboard Chapter 1 1 Introduction Page 1
PAGE 20
KINO-9453 Mini-ITX Motherboard 1.1 Introduction Figure 1-1: KINO-9453 Embedded SBC The KINO-9453 Mini-ITX form factor motherboard is an Intel® dual-core CPU platform. Intel® Core™2 Duo, Core Duo and Core Solo CPU are all supported to enhance the system processing speed. The KINO-9452 has a maximum front side bus (FSB) frequency of 667 MHz and contains two DDR2 SDRAM DIMM sockets that support up to 4 GB system memory.
PAGE 21
KINO-9453 Mini-ITX Motherboard 1.1.1 KINO-9453 Benefits Some of the KINO-9453 benefits are listed below: Multiple display output options Storage flexibility with support for SATA drives and IDE drives Expandable system with PCI and mini PCI slots DDR2 support enables faster data transfers Multiple I/O interfaces provide connectivity to a broad range of external peripheral devices 1.1.2 KINO-9453 Features Some of the KINO-9453 features are listed below.
PAGE 22
KINO-9453 Mini-ITX Motherboard Figure 1-2: KINO-9453 Overview 1.2.
PAGE 23
KINO-9453 Mini-ITX Motherboard 2 x Serial port connectors 2 x SATA connectors 1 x SPDIF connector 2 x USB connectors The KINO-9453 has the following external peripheral interface connectors on the board rear panel 2 x Audio jacks 1 x VGA connector 2 x Ethernet connectors 2 x Keyboard/Mouse connectors 2 x Serial port connectors 1 x DVI connector 4 x USB 2.
PAGE 24
KINO-9453 Mini-ITX Motherboard Specification KINO-9453 Socket 479 Intel® Celeron® M FSB 533 MHz (socket M) Front Side Bus 533 MHz or 667 MHz Northbridge: Intel® 945GME System Chipset Southbridge: Intel® ICH7-M Two 240-pin 400 MHz, 533 MHz or 667 MHz DDR2 SDRAM Memory DIMMs supported (system max.
PAGE 25
KINO-9453 Mini-ITX Motherboard Specification KINO-9453 Dimensions (LxW) 170 mm x 170 mm Weight (GW/NW) 900g/ 362g Table 1-1: Technical Specifications Page 7
PAGE 26
KINO-9453 Mini-ITX Motherboard Chapter 2 2 Detailed Specifications Page 8
PAGE 27
KINO-9453 Mini-ITX Motherboard 2.1 Overview This chapter describes the specifications and on-board features of the KINO-9453 in detail. 2.2 Dimensions 2.2.
PAGE 28
KINO-9453 Mini-ITX Motherboard 2.2.2 External Interface Panel Dimensions External peripheral interface connector panel dimensions are shown in Figure 2-2.
PAGE 29
KINO-9453 Mini-ITX Motherboard 2.3 Data Flow Figure 2-3 shows the data flow between the two on-board chipsets and other components installed on the motherboard and described in the following sections of this chapter.
PAGE 30
KINO-9453 Mini-ITX Motherboard 2.4 Compatible Processors 2.4.1 Compatible Processor Overview The KINO-9453 supports the following socket 479 processors: ® Intel ® Intel ® Intel Core™2 Duo Mobile processors Core™ Duo processors Core™ Solo processors Intel® Celeron® M processors The first three of the above processors communicate with the Intel® 945GME GMCH through a 667 MHz FSB and the Intel® Celeron® M processor through a 533 MHz FSB. Features of the supported processors are listed in Table 2-1.
PAGE 31
KINO-9453 Mini-ITX Motherboard Family Core™ Duo Core™ Solo Celeron® M sSpec# CPU Speed Processor # Bus Speed Mfg Tech Stepping Cache Size SL9SQ 1.66 GHz T5500 667 MHz 65 nm B2 2 MB SL8VT 2 GHz T2500 667 MHz 65 nm C0 2 MB SL9DN 1.66 GHz T2300E 667 MHz 65 nm C0 2 MB SL92X 1.83 GHz T1400 667 MHz 65 nm C0 2 MB SL9VA 1.73 GHz 530 533 MHz 65 nm A1 1 MB SL9LF 1.86 GHz 440 533 MHz 65 nm D0 1 MB Table 2-2: Supported Processors 2.
PAGE 32
KINO-9453 Mini-ITX Motherboard The Intel® 945GME Northbridge chipset on the KINO-9453 supports two DDR2 240-pin DIMMs with the following features: Two 240-pin DIMMs DDR2 only (DO NOT install a DDR DIMM) Single-channel or dual-channel Capacities of 256 MB, 512 MB, 1 GB or 2 GB Transfer speeds of 400 MHz, 533 MHz, or 667 MHz The memory sockets are shown in Figure 2-4. Figure 2-4: 240-pin DIMM Sockets 2.5.3 Intel® 945GME Integrated Graphics The Intel® 945GME Northbridge chipset has an Intel® Gen. 3.
PAGE 33
KINO-9453 Mini-ITX Motherboard 2.5.3.1 Intel® 945GME Analog CRT Support A DB-15 VGA connector on the external peripheral interface connector panel is interfaced to the Intel® 945GME graphics engine. The Intel® 945GME internal graphics engine, with an integrated 400 MHz RAMDAC and hot plug CRT support, supports analog CRT monitors up to QXGA. 2.5.3.2 Intel® 945GME LVDS Support A 30-pin LVDS crimp connector is interfaced to the Intel® 945GME graphics engine.
PAGE 34
KINO-9453 Mini-ITX Motherboard 2.6 Intel® ICH7-M Southbridge Chipset 2.6.1 Intel® ICH7-M Overview The Intel® ICH7-M Southbridge chipset is connected to the Intel® 945GME Northbridge GMCH through the chip-to-chip Direct Media Interface (DMI). Some of the features of the Intel® ICH7-M are listed below. Complies with PCI Express Base Specification, Revision 1.0a Complies with PCI Local Bus Specification, Revision 2.
PAGE 35
KINO-9453 Mini-ITX Motherboard Front right Back left Back right Center Subwoofer 2.6.3 Intel® ICH7-M IDE Interface The integrated IDE interface on the ICH7-M Southbridge supports two IDE hard disks and ATAPI devices. PIO IDE transfers up to 16 MB/s and Ultra ATA transfers of 100 MB/s.
PAGE 36
KINO-9453 Mini-ITX Motherboard 2.6.5 Intel® ICH7-M PCI Interface The PCI interface on the ICH7-M is compliant with the PCI Revision 2.3 implementation. Some of the features of the PCI interface are listed below. PCI Revision 2.3 compliant 33 MHz 5 V tolerant PCI signals (except PME#) Integrated PCI arbiter supports up to seven PCI bus masters 2.6.6 Intel® ICH7-M Real Time Clock 256 bytes of battery backed RAM is provided by the Motorola MC146818A real time clock (RTC) integrated into the ICH7-M.
PAGE 37
KINO-9453 Mini-ITX Motherboard 2.7 PCIe Bus Components 2.7.1 PCIe Bus Overview The PCIe bus is connected to components listed below: Two PCIe GbE Broadcom LAN controllers 2.7.2 Broadcom PCI Express GbE interface The Broadcom BCM5787M PCI Express (PCIe) GbE controller is a 10/100/1000BASE-T Ethernet LAN controller. The BCM5787M combines a triple-speed IEEE 802.3 compliant Media Access Controller (MAC) with a triple-speed Ethernet transceiver, a PCIe bus interface, and an on-chip buffer memory.
PAGE 38
KINO-9453 Mini-ITX Motherboard 2.8.2 BIOS Chipset The BIOS chipset has a licensed copy of AMI BIOS installed on the chipset. Some of the BIOS features are listed below: AMI Flash BIOS SMIBIOS (DMI) compliant Console redirection function support PXE (Pre-boot Execution Environment) support USB booting support 2.8.3 Super I/O chipset The iTE IT8712F Super I/O chipset is connected to the ICH7-M Southbridge through the LPC bus.
PAGE 39
KINO-9453 Mini-ITX Motherboard 2.8.3.1 Super I/O LPC Interface The LPC interface on the Super I/O complies with the Intel® Low Pin Count Specification Rev. 1.0. The LPC interface supports both LDRQ# and SERIRQ protocols as well as PCI PME# interfaces. 2.8.3.2 Super I/O 16C550 UARTs The on-board Super I/O has two integrated 16C550 UARTs that can support the following: Two standard serial ports (COM1 and COM2) IrDa 1.
PAGE 40
KINO-9453 Mini-ITX Motherboard 2.9 Environmental and Power Specifications 2.9.1 System Monitoring Three thermal inputs on the KINO-9453 Super I/O Enhanced Hardware Monitor monitor the following temperatures: System temperature Power temperature CPU temperature Eight voltage inputs on the KINO-9453 Super I/O Enhanced Hardware Monitor monitor the following voltages: CPU Core +2.5V +3.30V +5.00V +12.0V GMCH (1.5V) 1.
PAGE 41
KINO-9453 Mini-ITX Motherboard 2.9.2 Operating Temperature and Temperature Control The maximum and minimum operating temperatures for the KINO-9453 are listed below. Minimum Operating Temperature: 0ºC (32°F) Maximum Operating Temperature: 60°C (140°F) A cooling fan and heat sink must be installed on the CPU. Thermal paste must be smeared on the lower side of the heat sink before it is mounted on the CPU.
PAGE 42
KINO-9453 Mini-ITX Motherboard Chapter 3 3 Unpacking Page 24
PAGE 43
KINO-9453 Mini-ITX Motherboard 3.1 Anti-static Precautions WARNING: Failure to take ESD precautions during the installation of the KINO-9453 may result in permanent damage to the KINO-9453 and severe injury to the user. Electrostatic discharge (ESD) can cause serious damage to electronic components, including the KINO-9453. Dry climates are especially susceptible to ESD.
PAGE 44
KINO-9453 Mini-ITX Motherboard 3.3 Unpacking Checklist NOTE: If some of the components listed in the checklist below are missing, please do not proceed with the installation. Contact the IEI reseller or vendor you purchased the KINO-9453 from or contact an IEI sales representative directly. To contact an IEI sales representative, please send an email to sales@iei.com.tw. 3.3.
PAGE 45
KINO-9453 Mini-ITX Motherboard 1 SATA power cable (P/N: 32100-088600-RS) 1 Mini jumper Pack 1 Quick installation guide 1 Utility CD 1 I/O shielding Table 3-1: Package List Contents 3.3.2 Optional Items NOTE: The items listed in this section are optional items that must be ordered separately. Please contact your KINO-9453 vendor, distributor or reseller for more information or, contact IEI directly by sending an email to sales@iei.com.tw.
PAGE 46
KINO-9453 Mini-ITX Motherboard Quantity Item and Part Number 1 Dual port USB cable (P/N: CB-USB02-RS) 1 Four port USB cable (P/N: CB-USB14-RS) 1 RS-232/422/485 cable (P/N: 32200-000077-RS) 1 CPU Cooler (P/N: CF-479B-RS) Table 3-2: Optional Items Page 28 Image
PAGE 47
KINO-9453 Mini-ITX Motherboard Chapter 4 4 Connector Pinouts Page 29
PAGE 48
KINO-9453 Mini-ITX Motherboard 4.1 Peripheral Interface Connectors Section 4.1.1 shows peripheral interface connector locations. Section 4.1.2 lists all the peripheral interface connectors seen in Section 4.1.3. 4.1.1 KINO-9453 Layout Figure 4-1 shows the on-board peripheral connectors, rear panel peripheral connectors and on-board jumpers.
PAGE 49
KINO-9453 Mini-ITX Motherboard 4.1.2 Peripheral Interface Connectors Table 4-1 shows a list of the peripheral interface connectors on the KINO-9453. Detailed descriptions of these connectors can be found in Section 4.2.
PAGE 50
KINO-9453 Mini-ITX Motherboard 4.1.3 External Interface Panel Connectors Table 4-2 lists the rear panel connectors on the KINO-9453. Detailed descriptions of these connectors can be found in Section 4.3.
PAGE 51
KINO-9453 Mini-ITX Motherboard CN Pinouts: See Table 4-3 The cooling fan connectors on the KINO-9453 provide a 12 V, 500 mA current to one CPU cooling fan, one Northbridge cooling fan and one system cooling fan. There is a “sense” pin in the fan connector, which transfers the fan’s sense signal to the system BIOS in order to recognize the fan speed. Please note that only some specific types of fans offer a rotation signal. Figure 4-2: Fan Connector Locations PIN NO.
PAGE 52
KINO-9453 Mini-ITX Motherboard The front panel connector connects to several external switches and indicators to monitor and control the motherboard. These indicators and switches include: Power Power button Reset button Speaker HDD Figure 4-3: Front Panel Connector Location PIN NO. DESCRIPTION PIN NO.
PAGE 53
KINO-9453 Mini-ITX Motherboard CN Location: See Figure 4-4 CN Pinouts: See Table 4-5 The DIO connector is managed through a Super I/O chip. The DIO connector pins are user programmable. The digital IO port of KINO-9453 is 5 V CMOS level. Figure 4-4: GPIO Connector Location PIN NO. DESCRIPTION PIN NO. DESCRIPTION 1 GND 2 +5V 3 INPUT0 4 OUTPUT0 5 INPUT1 6 OUTPUT1 7 INPUT2 8 OUTPUT2 9 INPUT3 10 OUTPUT3 Table 4-5: GPIO Connector Pinouts 4.2.
PAGE 54
KINO-9453 Mini-ITX Motherboard One primary 40-pin IDE device connector on the KINO-9453 motherboard supports connectivity to ATA 100 IDE devices with data transfer rates up to 100 MB/s. Figure 4-5: IDE Device Connector Location PIN NO. DESCRIPTION PIN NO.
PAGE 55
KINO-9453 Mini-ITX Motherboard PIN NO. DESCRIPTION PIN NO. DESCRIPTION 13 DATA 2 14 DATA 13 15 DATA 1 16 DATA 14 17 DATA 0 18 DATA 15 19 GND 20 (KEY) 21 DRQ 22 GND 23 IOW# 24 GND 25 IOR# 26 GND 27 CHRDY 28 GND 29 DACK 30 GND 31 INTERRUPT 32 N/C 33 SA1 34 P66DET 35 SA0 36 SA2 37 HDC CS0# 38 HDC CS1# 39 HDD ACTIVE# 40 GND Table 4-6: IDE Connector Pinouts 4.2.
PAGE 56
KINO-9453 Mini-ITX Motherboard Figure 4-6: LCD Backlight Connector Location PIN NO. DESCRIPTION 1 Back Light Power 2 Back Light Power 3 Back Light enable 4 NC 5 GND 6 GND Table 4-7: LCD Backlight Connector Pinouts 4.2.6 LVDS LCD connector CN Label: LVDS1 CN Type: 30-pin connector (2x15) CN Location: See Figure 4-7 CN Pinouts: See Table 4-8 The connector supports one or two channel (18-bit or 24-bit) LVDS panel.
PAGE 57
KINO-9453 Mini-ITX Motherboard Figure 4-7: LVDS LCD Connector Location PIN NO. DESCRIPTION PIN NO.
PAGE 58
KINO-9453 Mini-ITX Motherboard 4.2.7 Mini PCI Slot CN Label: MINIPCI CN Type: 124-pin Mini PCI Type III slot CN Location: See Figure 4-8 CN Pinouts: See Table 4-9 Mini PCI is a small form factor version of a PCI card. Mini PCI expansion devices can be inserted into the Mini PCI slot. Figure 4-8: Mini PCI Slot Location PIN NAME PIN NAME PIN NAME PIN NAME 1 TIP 32 GROUND 63 3.
PAGE 59
KINO-9453 Mini-ITX Motherboard 10 8PMJ-5 41 AD[25] 72 DEVSEL# 103 AC_SYNC 11 LED1_GRNP 42 AD[28] 73 C/BE[1]# 104 M66EN 12 LED2_YELP 43 RESERVED 74 GROUND 105 AC_SDATA_IN 13 LED1_GRNN 44 AD[26] 75 AD[14] 106 AC_SDATA_OUT 14 LED2_YELN 45 C/BE[3]# 76 AD[15] 107 AC_BIT_CLK 15 CHSGND 46 AD[24] 77 GROUND 108 AC_CODEC_ID0# 16 RESERVED 47 AD[23] 78 AD[13] 109 AC_CODEC_ID1# 17 INTB# 48 IDSEL 79 AD[12] 110 AC_RESET# 18 5V 49 GROUND 80 AD[11] 111 M
PAGE 60
KINO-9453 Mini-ITX Motherboard Figure 4-9: Power Connector Location PIN NO. DESCRIPTION PIN NO. DESCRIPTION 1 3.3V 11 3.3V 2 3.3V 12 -12V 3 GND 13 GND 4 +5V 14 PS_ON 5 GND 15 GND 6 +5V 16 GND 7 GND 17 GND 8 Power good 18 -5V 9 5VSB 19 +5V 10 +12V 20 +5V Table 4-10: Power Connector Pinouts 4.2.
PAGE 61
KINO-9453 Mini-ITX Motherboard CN Pinouts: See Table 4-11 The serial ports connectors connect to RS-232/422/485 serial port device. Figure 4-10: 14-Pin Serial Port Connector Locations PIN NO. DESCRIPTION PIN NO. DESCRIPTION 1 DCD 2 DSR 3 RXD 4 RTS 5 TXD 6 CTS 7 DTR 8 RI 9 GND 10 NC 11 TX+ 12 TX- 13 RX+ 14 RX- Table 4-11: COM2 Pinouts 4.2.
PAGE 62
KINO-9453 Mini-ITX Motherboard Figure 4-11: 10-Pin Serial Port Connector Locations PIN NO. DESCRIPTION PIN NO. DESCRIPTION 1 DCD 2 DSR 3 RXD 4 RTS 5 TXD 6 CTS 7 DTR 8 RI 9 GND 10 NC Table 4-12: COM4 Pinouts 4.2.11 SATA Drive Connectors CN Label: SATA1 and SATA2 CN Type: 7-pin SATA drive connector (1x7) CN Location: See Figure 4-12 CN Pinouts: See Table 4-13 The two SATA drive connectors are connected to four SATA drives. SATA drives transfer data at speeds as high as 1.
PAGE 63
KINO-9453 Mini-ITX Motherboard Figure 4-12: SATA Drive Connector Locations PIN NO. DESCRIPTION 1 GND 2 TXP 3 TXN 4 GND 5 RXN 6 RXP 7 GND Table 4-13: SATA Drive Connector Pinouts 4.2.12 SPDIF Connector CN Label: SPDIF1 CN Type: 5-pin header (1x5) CN Location: See Figure 4-13 CN Pinouts: See Table 4-14 The SPDIF connector connects to the S/PDIF audio module, which bears S/PDIF digital output.
PAGE 64
KINO-9453 Mini-ITX Motherboard allows the user to enjoy digital audio. The SPDIF1 port provides digital audio to external speaker or compressed AC3 data to an external Dolby Digital Decoder via a coaxial cable. Figure 4-13: SPDIF Connector Locations PIN NO. DESCRIPTION 1 +5V 2 (KEY) 3 SPDIF_OUT 4 GND 5 SPDIF_IN Table 4-14: SPDIF Pinouts 4.2.
PAGE 65
KINO-9453 Mini-ITX Motherboard Figure 4-14: Internal USB Connector Locations PIN NO. DESCRIPTION PIN NO. DESCRIPTION 1 VCC 2 GND 3 DATA0- 4 DATA1+ 5 DATA0+ 6 DATA1- 7 GND 8 VCC Table 4-15: USB3 and USB4 Pinouts 4.3 External Interface Connectors The peripheral connectors on the back panel are connected to devices externally when the KINO-9453 is installed in a chassis.
PAGE 66
KINO-9453 Mini-ITX Motherboard Figure 4-15: KINO-9453 External Interface Connectors 4.3.1 Audio Connectors CN Label: AUDIO CN Type: Audio jack CN Location: See Figure 4-15 CN Pinouts: See Figure 4-16 Line Out port (Lime): Connects a headphone or a speaker. In 4,6,8-channel configuration, the function of this port becomes Front Speaker Out. Microphone (Pink): Connects a microphone. Figure 4-16: Audio Connectors 4.3.
PAGE 67
KINO-9453 Mini-ITX Motherboard CN Pinouts: See Table 4-16 The standard 15-pin VGA connector connects to a CRT or LCD display monitor. Figure 4-17: VGA Connector PIN NO. DESCRIPTION PIN NO. DESCRIPTION 1 RED 2 GREEN 3 BLUE 4 N/C 5 GND 6 GND 7 GND 8 GND 9 VCC 10 GND 11 N/C 12 DDC DAT 13 HSYNC 14 VSYNC 15 DDC CLK Table 4-16: VGA Connector Pinouts 4.3.
PAGE 68
KINO-9453 Mini-ITX Motherboard Figure 4-18 DVI-I Connector Pinout Locations PIN Description PIN Description PIN Description 1 DTX2- 9 DTX1- 17 DTX0- 2 DTX2+ 10 DTX1+ 18 DTX0+ 3 GND 11 GND 19 GND 4 N/C 12 N/C 20 N/C 5 N/C 13 N/C 21 N/C 6 SB_CK_C 14 PVDD1 22 GND 6 SB_DA_C 15 GND 23 DTXC+ 8 V_SYNC 16 GND 24 DTXC- C1 R C3 B 25 GND C5 GND C6 GND 26 GND C2 G C4 H_SYNC Table 4-17: DVI-I Connector Pinouts 4.3.
PAGE 69
KINO-9453 Mini-ITX Motherboard PIN DESCRIPTION PIN DESCRIPTION 1 MDX0+ 5 MDX2- 2 MDX0- 6 MDX1- 3 MDX1+ 7 MDX3+ 4 MDX2+ 8 MDX3- Table 4-18: LAN1 and LAN2 Pinouts Figure 4-19: RJ-45 Ethernet Connector The RJ-45 Ethernet connector has two status LEDs, one green and one yellow. The green LED indicates activity on the port and the yellow LED indicates the port is linked. See Table 4-19.
PAGE 70
KINO-9453 Mini-ITX Motherboard The KINO-9453 keyboard and mouse connectors are standard PS/2 connectors. Figure 4-20: PS/2 Pinouts PIN DESCRIPTION PIN DESCRIPTION 1 L_KDAT 7 L_MDAT 2 NC 8 NC 3 GND 9 GND 4 5V 10 5V 5 L_KCLK 11 L_MCLK 6 NC 12 NC Table 4-20: PS/2 Connector Pinouts 4.3.
PAGE 71
KINO-9453 Mini-ITX Motherboard Figure 4-21: External Serial Port Connector PIN Description 1 DATA CARRIER DETECT (DCD) 2 RECEIVE DATA (RXD) 3 TRANSMIT DATA (TXD) 4 DATA TERMINAL READY (DTR) 5 GROUND (GND) 6 DATA SET READY (DSR) 7 REQUEST TO SEND (RTS) 8 CLEAR TO SEND (CTS) 9 RING INDICATOR (RI) Table 4-21: External Serial Port Pinouts 4.3.
PAGE 72
KINO-9453 Mini-ITX Motherboard PIN NO. DESCRIPTION PIN NO.
PAGE 73
KINO-9453 Mini-ITX Motherboard Chapter 5 5 Installation Page 55
PAGE 74
KINO-9453 Mini-ITX Motherboard 5.1 Anti-static Precautions WARNING: Failure to take ESD precautions during the installation of the KINO-9453 may result in permanent damage to the KINO-9453 and severe injury to the user. Electrostatic discharge (ESD) can cause serious damage to electronic components, including the KINO-9453. Dry climates are especially susceptible to ESD.
PAGE 75
KINO-9453 Mini-ITX Motherboard 5.2 Installation Considerations NOTE: The following installation notices and installation considerations should be read and understood before the KINO-9453 is installed. All installation notices pertaining to the installation of the KINO-9453 should be strictly adhered to. Failing to adhere to these precautions may lead to severe damage of the KINO-9453 and injury to the person installing the motherboard. 5.2.
PAGE 76
KINO-9453 Mini-ITX Motherboard o When working with the KINO-9453, make sure that it is disconnected from all power supplies and that no electricity is being fed into the system. Before and during the installation of the KINO-9453 DO NOT: Remove any of the stickers on the PCB board. These stickers are required for warranty validation. Use the product before verifying all the cables and power connectors are properly connected.
PAGE 77
KINO-9453 Mini-ITX Motherboard o o o Keyboard Mouse RS-232 serial communications device 5.3 CPU, CPU Cooling Kit and DIMM Installation WARNING: A CPU should never be turned on without the specified cooling kit being installed. If the cooling kit (heat sink and fan) is not properly installed and the system turned on, permanent damage to the CPU, KINO-9453 and other electronic components attached to the system may be incurred. Running a CPU without a cooling kit may also result in injury to the user.
PAGE 78
KINO-9453 Mini-ITX Motherboard WARNING: When handling the CPU, only hold it on the sides. DO NOT touch the pins at the bottom of the CPU. Step 1: Unlock the CPU retention screw. When shipped, the retention screw of the CPU socket should be in the unlocked position. If it is not in the unlocked position, use a screwdriver to unlock the screw. See Figure 5-1. Figure 5-1: Make sure the CPU socket retention screw is unlocked Step 2: Inspect the CPU socket.
PAGE 79
KINO-9453 Mini-ITX Motherboard Step 5: Align the CPU pins. Carefully align the CPU pins with the holes in the CPU socket. Step 6: Insert the CPU. Gently insert the CPU into the socket. If the CPU pins are properly aligned, the CPU should slide into the CPU socket smoothly. Step 7: Lock the retention screw. Rotate the retention screw into the locked position. See Figure 5-2.
PAGE 80
KINO-9453 Mini-ITX Motherboard 5.3.2 Cooling Kit CF-479B-RS Installation Figure 5-3: IEI CF-479B-RS Cooling Kit An IEI Socket 479 CPU cooling kit can be purchased separately. The cooling kit comprises a CPU heat sink and a cooling fan. WARNING: Do not wipe off (accidentally or otherwise) the pre-sprayed layer of thermal paste on the bottom of the CF-479B-RS heat sink. The thermal paste between the CPU and the heat sink is important for optimum heat dissipation.
PAGE 81
KINO-9453 Mini-ITX Motherboard Figure 5-4: Cooling Kit Support Bracket Step 4: Tighten the screws. Use a screwdriver to tighten the four screws. Tighten each nut a few turns at a time and do not over-tighten the screws. Step 5: Connect the fan cable. Connect the cooling kit fan cable to the fan connector on the motherboard. Carefully route the cable and avoid heat generating chips and fan blades. See Figure 5-5.
PAGE 82
KINO-9453 Mini-ITX Motherboard 5.3.3 DIMM Installation WARNING: Only DDR2 memory module can be installed on the KINO-9453. Do not install DDR memory modules. If a DDR memory module is installed on the KINO-9453, the KINO-9453 may be irreparably damaged. Please make sure the purchased DIMM complies with the memory specifications of the KINO-9453. DIMM specifications compliant with the KINO-9453 are listed in Chapter 2.
PAGE 83
KINO-9453 Mini-ITX Motherboard Step 2: Align the DIMM with the socket. The DIMM must be oriented in such a way that the notch in the middle of the DIMM must be aligned with the plastic bridge in the socket. See Figure 5-6. Step 3: Insert the DIMM. Once properly aligned, the DIMM can be inserted into the socket. As the DIMM is inserted, the white handles on the side of the socket will close automatically and secure the DIMM to the socket. See Figure 5-6. Step 4: Removing a DIMM.
PAGE 84
KINO-9453 Mini-ITX Motherboard LVDS screen resolution selection JP2 8-pin header RS-422 Termination Resister JP8 2-pin header RS-485 Termination Resister JP9 2-pin header Table 5-1: Jumpers 5.4.1 AT/ATX Power Select Jumper Settings Jumper Label: JP5 and JP6 Jumper Type: 2-pin header Jumper Settings: See Table 5-2 Jumper Location: See Figure 5-8 The AT/ATX Power Select jumper specifies the systems power mode as AT or ATX. AT/ATX Power Select jumper settings are shown in Table 5-2.
PAGE 85
KINO-9453 Mini-ITX Motherboard Figure 5-8: AT/ATX Power Select Jumper Location 5.4.2 Clear CMOS Jumper Jumper Label: JP3 Jumper Type: 3-pin header Jumper Settings: See Table 5-3 Jumper Location: See Figure 5-9 If the KINO-9453 fails to boot due to improper BIOS settings, the clear CMOS jumper clears the CMOS data and resets the system BIOS information. To do this, use the jumper cap to close pins 2 and 3 for a few seconds then reinstall the jumper clip back to pins 1 and 2.
PAGE 86
KINO-9453 Mini-ITX Motherboard Enter the correct CMOS setting Load Optimal Defaults Load Failsafe Defaults. After having done one of the above, save the changes and exit the CMOS Setup menu. The clear CMOS jumper settings are shown in Table 5-3. Clear CMOS Description Short 1 - 2 Keep CMOS Setup Short 2 - 3 Clear CMOS Setup Default Table 5-3: Clear CMOS Jumper Settings The location of the clear CMOS jumper is shown in Figure 5-9 below.
PAGE 87
KINO-9453 Mini-ITX Motherboard 5.4.3 COM 3 Function Select Jumper Jumper Label: JP1 and JP7 Jumper Type: 6-pin header Jumper Settings: See Table 5-4 Jumper Location: See Figure 5-10 The COM 3 Function Select jumper sets the communication protocol used by the second serial communications port (COM 3) as RS-232, RS-422 or RS-485. The COM 3 Function Select settings are shown in Table 5-4.
PAGE 88
KINO-9453 Mini-ITX Motherboard Figure 5-10: COM 3 Function Select Jumper Locations 5.4.4 RS-422 or RS-486 Termination Resister Jumper Label: JP8 and JP9 Jumper Type: 2-pin header Jumper Settings: See Table 5-5 and Table 5-6 Jumper Location: See Figure 5-11 The JP8 sets the RS-422 Termination Resister while JP9 sets the RS-485 Termination Resister. The RS-422 and RS-485 Termination Resister settings are shown in Table 5-5 and Table 5-6.
PAGE 89
KINO-9453 Mini-ITX Motherboard JP9 Description Open Normal Operation Short Termination Resister Setting Default Table 5-6: RS-485 Termination Resister Jumper Settings The RS-422 or RS-485 Termination Resister jumper location is shown in Figure 5-11. Figure 5-11: RS-422 and RS-485 Termination Resister Jumper Locations 5.4.
PAGE 90
KINO-9453 Mini-ITX Motherboard LVDS Resolution Select Description Open By BIOS setting Short 3-4 800 x 600 (18-bit) Short 5-6 1024 x 768 (24-bit) Short 1-2, 3-4 1024 x 768 (18-bit) Short 1-2, 3-4, 5-6 1600 x 1200 (48-bit) Short 3-4, 5-6 1280 x 1024 (48-bit) Short 7-8 1280 x 768 (18-bit) Short 1-2, 7-8 1280 x 800 (18-bit) Short 3-4, 7-8 1366 x 768 (18-bit) Short 1-2, 3-4, 7-8 1440 x 900 (36-bit) Short 5-6, 7-8 1440 x 900 (48-bit) Short 1-2, 5-6, 7-8 1680 x 1050 (48-bit) Default Tab
PAGE 91
KINO-9453 Mini-ITX Motherboard Figure 5-12: LVDS Screen Resolution Selection Jumper Pinout Locations 5.4.6 LVDS Voltage Selection WARNING: Permanent damage to the screen and KINO-9453 may occur if the wrong voltage is selected with this jumper. Please refer to the user guide that cam with the monitor to select the correct voltage.
PAGE 92
KINO-9453 Mini-ITX Motherboard The LVDS Voltage Selection jumper allows the LVDS screen voltage to be set. The LVDS Voltage Selection jumper settings are shown in Table 5-8. LVDS Voltage Select Description Short 1-2 +3V Short 3-4 +5V Default Table 5-8: LVDS Voltage Selection Jumper Settings The LVDS Voltage Selection jumper location. is shown in Figure 5-13.
PAGE 93
KINO-9453 Mini-ITX Motherboard 5.5 Chassis Installation 5.5.1 Airflow WARNING: Airflow is critical to the cooling of the CPU and other onboard components. The chassis in which the KINO-9453 must have air vents to allow cool air to move into the system and hot air to move out. The KINO-9453 must be installed in a chassis with ventilation holes on the sides allowing airflow to travel through the heat sink surface.
PAGE 94
KINO-9453 Mini-ITX Motherboard 5.6 Internal Peripheral Device Connections 5.6.1 Peripheral Device Cables The cables listed in Table 5-9 are shipped with the KINO-9453. Quantity Type 1 IDE Cable 1 Dual RS-232 cable 2 SATA drive cables 1 SATA drive power cable Table 5-9: IEI Provided Cables Optional cables are listed below: USB cable (dual port) USB cable (four port) RS-232/422/485 cable 5.6.2 IDE Cable Connection The IDE flat cable connects to the KINO-9453 to one or two IDE devices.
PAGE 95
KINO-9453 Mini-ITX Motherboard Figure 5-14: IDE Cable Connection Step 3: Connect the cable to an IDE device. Connect the two connectors on the other side of the cable to one or two IDE devices. Make sure that pin 1 on the cable corresponds to pin 1 on the connectorStep 0: 5.6.3 Dual RS-232 Cable Connection The dual RS-232 cable consists of two connectors attached to two independent cables. Each cable is then attached to a D-sub 9 male connector that is mounted onto a bracket.
PAGE 96
KINO-9453 Mini-ITX Motherboard Figure 5-15: Dual RS-232 Cable Installation Step 3: Secure the bracket. The dual RS-232 connector has two D-sub 9 male connectors secured on a bracket. To secure the bracket to the chassis please refer to the reference material that came with the chassisStep 0: 5.6.4 SATA Drive Connection The KINO-9453 is shipped with two SATA drive cables and one SATA drive power cable. To connect the SATA drives to the connectors, please follow the steps below.
PAGE 97
KINO-9453 Mini-ITX Motherboard Figure 5-16: SATA Drive Cable Connection Step 3: Connect the cable to the SATA disk. Connect the connector on the other end of the cable to the connector at the back of the SATA drive. See Figure 5-17. Step 4: Connect the SATA power cable. Connect the SATA power connector to the back of the SATA drive. See Figure 5-17.
PAGE 98
KINO-9453 Mini-ITX Motherboard 5.7 External Peripheral Interface Connection The following external peripheral devices can be connected to the external peripheral interface connectors. Audio devices RJ-45 Ethernet cable USB devices VGA monitors DVI port devices Serial port devices Mouse and keyboard To install these devices, connect the corresponding cable connector from the actual device to the corresponding KINO-9453 external peripheral interface connector making sure the pins are properly aligned. 5.7.
PAGE 99
KINO-9453 Mini-ITX Motherboard Figure 5-18: Audio Connectors 5.7.2 RJ-45 Ethernet Connection The KINO-9453 has two RJ-45 Ethernet connectors on the external peripheral interface panel for LAN communications. Follow the steps below to connect an RJ-45 Ethernet connector to the KINO-9453. Step 1: Locate the RJ-45 connector. The location of the RJ-45 connector is shown in Chapter 3. Step 2: Insert an RJ-45 plug. Insert the RJ-45 plug of a LAN into the RJ-45 receptacle on the external peripheral interface.
PAGE 100
KINO-9453 Mini-ITX Motherboard Figure 5-19: RJ-45 Ethernet Connector 5.7.3 USB Connection The external USB Series "A" receptacle connectors provide easier and quicker access to external USB devices. Follow the steps below to connect USB devices to the KINO-9453. Step 1: Locate the USB Series "A" receptacle connectors. The location of the USB Series "A" receptacle connectors are shown in Chapter 3. Step 2: Insert a USB Series "A" plug.
PAGE 101
KINO-9453 Mini-ITX Motherboard Figure 5-20: USB Connector 5.7.4 VGA Monitor Connection The KINO-9453 has a single female DB-15 connector on the external peripheral interface panel. The DB-15 connector is connected to a CRT or VGA monitor. To connect a monitor to the KINO-9453, please follow the instructions below. Step 1: Locate the female DB-15 connector. The location of the female DB-15 connector is shown in Chapter 3. Step 2: Align the VGA connector.
PAGE 102
KINO-9453 Mini-ITX Motherboard Figure 5-21: VGA Connector Step 4: Secure the connector. Secure the DB-15 VGA connector from the VGA monitor to the external interface by tightening the two retention screws on either side of the connector. Step 0: 5.7.5 Serial Device Connection The KINO-9453 has two female DB-9 connectors on the external peripheral interface panel for serial devices. Follow the steps below to connect a serial device to the KINO-9453. Step 1: Locate the DB-9 connector.
PAGE 103
KINO-9453 Mini-ITX Motherboard Figure 5-22: Serial Device Connector Step 3: Secure the connector. Secure the serial device connector to the external interface by tightening the two retention screws on either side of the connector. Step 0: 5.7.6 PS/2 Keyboard/Mouse Connection The KINO-9453 has a dual PS/2 connector on the external peripheral interface panel. The dual PS/2 connector is used to connect to a keyboard and mouse to the system.
PAGE 104
KINO-9453 Mini-ITX Motherboard Figure 5-23: PS/2 Keyboard/Mouse Connector Page 86
PAGE 105
KINO-9453 Mini-ITX Motherboard Chapter 6 6 AMI BIOS Page 87
PAGE 106
KINO-9453 Mini-ITX Motherboard 6.1 Introduction A licensed copy of AMI BIOS is preprogrammed into the ROM BIOS. The BIOS setup program allows users to modify the basic system configuration. This chapter describes how to access the BIOS setup program and the configuration options that may be changed. 6.1.1 Starting Setup The AMI BIOS is activated when the computer is turned on. The setup program can be activated in one of two ways. 1. Press the DELETE key as soon as the system is turned on or 2.
PAGE 107
KINO-9453 Mini-ITX Motherboard Key Function F1 key General help, only for Status Page Setup Menu and Option Page Setup Menu F2 /F3 key Change color from total 16 colors. F2 to select color forward. F10 key Save all the CMOS changes, only for Main Menu Table 6-1: BIOS Navigation Keys 6.1.3 Getting Help When F1 is pressed a small help window describing the appropriate keys to use and the possible selections for the highlighted item appears. To exit the Help Window press ESC or the F1 key again. 6.1.
PAGE 108
KINO-9453 Mini-ITX Motherboard 6.2 Main The Main BIOS menu (BIOS Menu 1) appears when the BIOS Setup program is entered. The Main menu gives an overview of the basic system information. BIOS Menu 1: Main System Overview The System Overview lists a brief summary of different system components. The fields in System Overview cannot be changed.
PAGE 109
KINO-9453 Mini-ITX Motherboard o o Speed: Lists the processor speed Count: The number of CPUs on the motherboard System Memory: Displays the auto-detected system memory. o Size: Lists memory size The System Overview field also has two user configurable fields: System Time [xx:xx:xx] Use the System Time option to set the system time. Manually enter the hours, minutes and seconds. System Date [xx/xx/xx] Use the System Date option to set the system date. Manually enter the day, month and year. 6.
PAGE 110
KINO-9453 Mini-ITX Motherboard Remote Access Configuration (see Section 6.3.7) USB Configuration (see Section 6.3.8) BIOS Menu 2: Advanced 6.3.1 CPU Configuration Use the CPU Configuration menu (BIOS Menu 3) to view detailed CPU specifications and configure the CPU.
PAGE 111
KINO-9453 Mini-ITX Motherboard BIOS Menu 3: CPU Configuration The CPU Configuration menu (BIOS Menu 3) lists the following CPU details: Manufacturer: Lists the name of the CPU manufacturer Brand String: Lists the brand name of the CPU being used Frequency: Lists the CPU processing speed FSB Speed: Lists the FSB speed Cache L1: Lists the CPU L1 cache size Cache L2: Lists the CPU L2 cache size 6.3.
PAGE 112
KINO-9453 Mini-ITX Motherboard BIOS Menu 4: IDE Configuration ATA/IDE Configuration [Enhanced] The ATA/IDE Configuration BIOS option allows the user to configure the ATA/IDE device mode. Disable all ATA/IDE ports. No Primary/Secondary IDE Disabled mode is presented for configuration Up to 6 HDDs can be used, four for SATA and the other Compatible for PATA IDE. If this option is selected, “Legacy IDE Channels” option is presented for configuration.
PAGE 113
KINO-9453 Mini-ITX Motherboard SATA channels” options are presented for configuration. Configure SATA as [IDE] Use the Configure SATA as option to specify how to configure the available SATA devices.
PAGE 114
KINO-9453 Mini-ITX Motherboard Secondary IDE Slave Third IDE Master Third IDE Slave The IDE Configuration menu (BIOS Menu 4) allows changes to the configurations for the IDE devices installed in the system. If an IDE device is detected, and one of the above listed four BIOS configuration options are selected, the IDE configuration options shown in Section 6.3.2.1 appear. 6.3.2.
PAGE 115
KINO-9453 Mini-ITX Motherboard Use the Type BIOS option select the type of device the AMIBIOS attempts to boot from after the Power-On Self-Test (POST) is complete. BIOS is prevented from searching for an IDE disk Not Installed drive on the specified channel. Auto DEFAULT The BIOS auto detects the IDE disk drive type attached to the specified channel. This setting should be used if an IDE hard disk drive is attached to the specified channel.
PAGE 116
KINO-9453 Mini-ITX Motherboard Block (Multi-Sector Transfer) [Auto] Use the Block (Multi Sector Transfer) to disable or enable BIOS to auto detect if the device supports multi-sector transfers. BIOS is prevented from using Multi-Sector Transfer on the Disabled specified channel. The data to and from the device occurs one sector at a time. Auto DEFAULT BIOS auto detects Multi-Sector Transfer support on the drive on the specified channel.
PAGE 117
KINO-9453 Mini-ITX Motherboard DMA Mode [Auto] Use the DMA Mode BIOS selection to adjust the DMA mode options. Auto DEFAULT BIOS auto detects the DMA mode. Use this value if the IDE disk drive support cannot be determined. SWDMA0 Single Word DMA mode 0 selected with a maximum data transfer rate of 2.1MBps SWDMA1 Single Word DMA mode 1 selected with a maximum data transfer rate of 4.2MBps SWDMA2 Single Word DMA mode 2 selected with a maximum data transfer rate of 8.
PAGE 118
KINO-9453 Mini-ITX Motherboard Ultra DMA mode 4 selected with a maximum data transfer UDMA4 rate of 66.6MBps (To use this mode, it is required that an 80-conductor ATA cable is used.) Ultra DMA mode 5 selected with a maximum data transfer UDMA5 rate of 99.9MBps (To use this mode, it is required that an 80-conductor ATA cable is used.) S.M.A.R.T [Auto] Use the S.M.A.R.
PAGE 119
KINO-9453 Mini-ITX Motherboard BIOS Menu 6: Super IO Configuration Serial Port1 Address [3F8/IRQ4] Use the Serial Port1 Address option to select the Serial Port 1 base address.
PAGE 120
KINO-9453 Mini-ITX Motherboard Serial Port1 Mode [Normal] Use the Serial Port1 Mode option to select the transmitting and receiving mode for the first serial port. Normal (Default) Serial Port 1 mode is normal IrDA Serial Port 1 mode is IrDA ASK IR Serial Port 1 mode is ASK IR Serial Port2 Address [2F8/IRQ3] Use the Serial Port2 Address option to select the Serial Port 2 base address.
PAGE 121
KINO-9453 Mini-ITX Motherboard No base address is assigned to serial port 3 Disabled 3E8 DEFAULT Serial port 3 I/O port address is 3E8 2E8 Serial port 3 I/O port address is 2E8 2F0 Serial port 3 I/O port address is 2F0 2E0 Serial port 3 I/O port address is 2E0 Serial Port3 IRQ [11] Use the Serial Port3 IRQ option to select the interrupt address for serial port 3.
PAGE 122
KINO-9453 Mini-ITX Motherboard 6.3.4 Hardware Health Configuration The Hardware Health Configuration menu (BIOS Menu 7) shows the operating temperature, fan speeds and system voltages. BIOS Menu 7: Hardware Health Configuration CPU FAN Mode Setting [Full On Mode] Use the CPU FAN Mode Setting option to configure the second fan. Full On Mode Automatic mode DEFAULT Fan is on all the time Fan is off when the temperature is low enough. Parameters must be set by the user.
PAGE 123
KINO-9453 Mini-ITX Motherboard When the CPU FAN Mode Setting option is in the Automatic Mode, the following parameters can be set. CPU Temp. Limit of OFF CPU Temp. Limit of Start CPU Temp. Limit of Full CPU Fan Start PWM Slope PWM 1 When the CPU FAN Mode Setting option is in the PWM Manual Mode, the following parameters can be set. CPU Fan PWM control CPU Temp.
PAGE 124
KINO-9453 Mini-ITX Motherboard WARNING: Setting this value too high may cause the fan to start only when the CPU is at a high temperature and therefore cause the system to be damaged. The CPU Temp. Limit of Start option can only be set if the CPU FAN Mode Setting option is set to Automatic Mode. Use the CPU Temp. Limit of Start option to select the CPU temperature at which the cooling fan should automatically turn on.
PAGE 125
KINO-9453 Mini-ITX Motherboard speed. To select a value, select the CPU Temp. Limit of Full option and enter a decimal number between 000 and 127. The temperature range is specified below. Minimum Value: 0°C Maximum Value: 127°C CPU Fan Start PWM [070] The CPU Fan Start PWM option can only be set if the CPU FAN Mode Setting option is set to Automatic Mode. Use the CPU Fan Start PWM option to select the PWM mode the fan starts to rotate with after the temperature specified in the CPU Temp.
PAGE 126
KINO-9453 Mini-ITX Motherboard CPU Fan PWM Control [100] The CPU Fan PWM Control option can only be set if the CPU FAN Mode Setting option is set to Manual Mode. Use the CPU Fan PWM Control option to select PWM duty cycle control. The PWM duty cycle specifies the width of the modulated pulse. A high value ensures a wide pulse and a low value ensures a narrow pulse. To select a value, select the CPU Fan PWM Control option and enter a decimal number between 000 and 127.
PAGE 127
KINO-9453 Mini-ITX Motherboard 6.3.5 ACPI Configuration The ACPI Configuration menu (BIOS Menu 8) configures the Advanced Configuration and Power Interface (ACPI) and Power Management (APM) options. BIOS Menu 8: ACPI Configuration 6.3.5.1 General ACPI Configuration Use the General ACPI Configuration menu (BIOS Menu 9) to select the ACPI state when the system is suspended.
PAGE 128
KINO-9453 Mini-ITX Motherboard BIOS Menu 9: General ACPI Configuration [Advanced\ ACPI Configuration] Suspend Mode [S3 (STR)] Use the Suspend Mode option to specify the sleep state the system enters when it is not being used. The system enters S1(POS) sleep state. The system S1 (POS) appears off. The CPU is stopped; RAM is refreshed; the system is running in a low power mode. S3 (STR) DEFAULT The system enters a S3(STR) sleep state.
PAGE 129
KINO-9453 Mini-ITX Motherboard 6.3.6 APM Configuration The APM Configuration menu (BIOS Menu 10) allows the advanced power management options to be configured. BIOS Menu 10:Advanced Power Management Configuration Power Management/APM [Enabled] Use the Power Management/APM BIOS option to enable access to the advanced power management features. If this option is disabled, the only other option on the screen is the Power Button Mode.
PAGE 130
KINO-9453 Mini-ITX Motherboard Power Supply Mode [ATX] Use the Power Supply Mode BIOS option to to select the power supply that is connected to the system. An AT power supply is connected to the system AT ATX DEFAULT An ATX power supply is connected to the system Restore on AC Power Loss by IO [Power Off] Use the Restore on AC Power Loss by IO BIOS option to specify what state the system returns to if there is a sudden loss of power to the system.
PAGE 131
KINO-9453 Mini-ITX Motherboard activity Wake event generated by PCI PME controller activity Enabled Resume On RTC Alarm [Disabled] Use the Resume On RTC Alarm option to specify the time the system should be roused from a suspended state.
PAGE 132
KINO-9453 Mini-ITX Motherboard BIOS Menu 11: Remote Access Configuration [Advanced] Remote Access [Disabled] Use the Remote Access option to enable or disable access to the remote functionalities of the system. Disabled Enabled DEFAULT Remote access is disabled.
PAGE 133
KINO-9453 Mini-ITX Motherboard Terminal Type VT-UTF8 Combo Key Support Sredir Memory Display Delay These configuration options are discussed below. Serial Port Number [COM1] Use the Serial Port Number option allows to select the serial port used for remote access. COM1 DEFAULT COM2 System is remotely accessed through COM1 System is remotely accessed through COM2 NOTE: Make sure the selected COM port is enabled through the Super I/O configuration menu.
PAGE 134
KINO-9453 Mini-ITX Motherboard NOTE: Identical baud rate setting musts be set on the host (a management computer running a terminal software) and the slave Flow Control [None] Use the Flow Control option to report the flow control method for the console redirection application.
PAGE 135
KINO-9453 Mini-ITX Motherboard VT100 The target terminal type is VT100 VT-UTF8 The target terminal type is VT-UTF8 VT-UTF8 Combo Key Support [Disabled] Use the VT-UFT8 Combo Key Support option to enable additional keys that are not provided by VT100 for the PC 101 keyboard. The VT100 Terminal Definition is the standard convention used to configure and conduct emergency management tasks with UNIX-based servers. VT100 does not support all keys on the standard PC 101-key layout, however.
PAGE 136
KINO-9453 Mini-ITX Motherboard BIOS Menu 12: USB Configuration USB Function [8 USB ports] Use the USB Function BIOS option to enable or disable a specified number of USB ports. If only two USB ports are being used, disabling the remaining six USB frees up system resources that can be redirected elsewehere.
PAGE 137
KINO-9453 Mini-ITX Motherboard USB 2.0 Controller [Enabled] Use the USB 2.0 Controller BIOS option to enable or disable the USB 2.0 controller USB 2.0 controller disabled Disabled Enabled DEFAULT USB 2.0 controller enabled Legacy USB Support [Enabled] Use the Legacy USB Support BIOS option to enable USB mouse and USB keyboard support.
PAGE 138
KINO-9453 Mini-ITX Motherboard Systems with OSes that do not support EHCI can Disabled use the EHCI handoff functionality. Enabled DEFAULT Systems with OSes that do not support EHCI cannot use the EHCI handoff functionality. 6.3.8.1 USB Mass Storage Device Configuration Use the USB Mass Storage Device Configuration menu (?????) to configure USB mass storage class devices.
PAGE 139
KINO-9453 Mini-ITX Motherboard POST waits 10 seconds for the USB mass storage 10 Sec device after the start unit command. 20 Sec DEFAULT POST waits 20 seconds for the USB mass storage device after the start unit command. 30 Sec POST waits 30 seconds for the USB mass storage device after the start unit command. 40 Sec POST waits 40 seconds for the USB mass storage device after the start unit command. Device ## The Device## field lists the USB devices that are connected to the system.
PAGE 140
KINO-9453 Mini-ITX Motherboard Auto Floppy DEFAULT BIOS auto-detects the current USB. The USB device will be emulated as a floppy drive. The device can be either A: or B: responding to INT13h calls that return DL = 0 or DL = 1 respectively. Forced FDD Allows a hard disk image to be connected as a floppy image. This option works only for drives formatted with FAT12, FAT16 or FAT32.
PAGE 141
KINO-9453 Mini-ITX Motherboard BIOS Menu 14: PCI/PnP Configuration Page 123
PAGE 142
KINO-9453 Mini-ITX Motherboard Clear NVRAM [No] Use the Clear NVRAM option to specify if the NVRAM (Non-Volatile RAM) is cleared when the power is turned off. No DEFAULT System does not clear NVRAM during system boot System clears NVRAM during system boot Yes Plug & Play O/S [No] Use the Plug & Play O/S BIOS option to specify whether system plug and play devices are configured by the operating system or the BIOS.
PAGE 143
KINO-9453 Mini-ITX Motherboard Allocate IRQ to PCI VGA [Yes] Use the Allocate IRQ to PCI VGA option to restrict the system from giving the VGA adapter card an interrupt address. Yes (Default) Assigns an IRQ to a PCI VGA card if card requests IRQ Does not assign IRQ to a PCI VGA card even if the card No requests an IRQ Palette Snooping [Disabled] Use the Palette Snooping option to enable or disable the palette snooping function.
PAGE 144
KINO-9453 Mini-ITX Motherboard OffBoard PCI/ISA IDE Card [Auto] Use the OffBoard PCI/ISA IDE Card BIOS option to select the OffBoard PCI/ISA IDE Card. Auto DEFAULT The location of the Off Board PCI IDE adapter card is automatically detected by the AMIBIOS. PCI Slot 1 PCI Slot 1 is selected as the location of the OffBoard PCI IDE adapter card. Only select this slot if the adapter card is installed in PCI Slot 1. PCI Slot 2 PCI Slot 2 is selected as the location of the OffBoard PCI IDE adapter card.
PAGE 145
KINO-9453 Mini-ITX Motherboard Available DEFAULT The specified IRQ is available to be used by PCI/PnP devices The specified IRQ is reserved for use by Legacy ISA Reserved devices Available IRQ addresses are: IRQ3 IRQ4 IRQ5 IRQ7 IRQ9 IRQ10 IRQ 11 IRQ 14 IRQ 15 DMA Channel# [Available] Use the DMA Channel# option to assign a specific DMA channel to a particular PCI/PnP device.
PAGE 146
KINO-9453 Mini-ITX Motherboard DM Channel 7 Reserved Memory Size [Disabled] Use the Reserved Memory Size BIOS option to specify the amount of memory that should be reserved for legacy ISA devices. Disabled DEFAULT No memory block reserved for legacy ISA devices 16K 16KB reserved for legacy ISA devices 32K 32KB reserved for legacy ISA devices 64K 54KB reserved for legacy ISA devices 6.5 Boot Use the Boot menu (BIOS Menu 15) to configure system boot options.
PAGE 147
KINO-9453 Mini-ITX Motherboard 6.5.1 Boot Settings Configuration Use the Boot Settings Configuration menu (BIOS Menu 15) to configure advanced system boot options. BIOS Menu 16: Boot Settings Configuration Quick Boot [Enabled] Use the Quick Boot BIOS option to make the computer speed up the boot process.
PAGE 148
KINO-9453 Mini-ITX Motherboard Disabled DEFAULT Normal POST messages displayed OEM Logo displayed instead of POST messages Enabled AddOn ROM Display Mode [Force BIOS] Use the AddOn ROM Display Mode option to allow add-on ROM (read-only memory) messages to be displayed. Force BIOS DEFAULT The system forces third party BIOS to display during system boot. The system displays normal information during Keep Current system boot.
PAGE 149
KINO-9453 Mini-ITX Motherboard PS/2 mouse support is disabled and prevented from Disabled using system resources. Allows the system to use a PS/2 mouse. Enabled Auto DEFAULT The system auto-adjusts PS/2 mouse support. Boot From LAN Support [Disabled] Use the Boot From LAN Support option to enable the system to be booted from a remote system. Disabled DEFAULT Cannot be booted from a remote system through the LAN Enabled Can be booted from a remote system through the LAN 6.5.
PAGE 150
KINO-9453 Mini-ITX Motherboard BIOS Menu 17: Boot Device Priority Settings Page 132
PAGE 151
KINO-9453 Mini-ITX Motherboard 6.5.3 Removable Drives Use the Removable Drives menu (BIOS Menu 18) to specify the boot sequence of the available FDDs. When the menu is opened, the FDDs connected to the system are listed as shown below: 1st Drive [1st FLOPPY DRIVE] 2nd Drive [2nd FLOPPY DRIVE] NOTE: Only the drives connected to the system are shown. For example, if only one FDD is connected only “1st Drive” is listed. The boot sequence from the available devices is selected.
PAGE 152
KINO-9453 Mini-ITX Motherboard 6.6 Security Use the Security menu (BIOS Menu 19) to set system and user passwords. BIOS Menu 19: Security Change Supervisor Password Use the Change Supervisor Password to set or change a supervisor password. The default for this option is Not Installed. If a supervisor password must be installed, select this field and enter the password. After the password has been added, Install appears next to Change Supervisor Password.
PAGE 153
KINO-9453 Mini-ITX Motherboard password. After the password has been added, Install appears next to Change User Password. 6.7 Chipset Use the Chipset menu (BIOS Menu 20) to access the NorthBridge and SouthBridge configuration menus. WARNING: Setting the wrong values for the Chipset BIOS selections in the Chipset BIOS menu may cause the system to malfunction.
PAGE 154
KINO-9453 Mini-ITX Motherboard 6.7.1 NorthBridge Configuration Use the NorthBridge Configuration menu (BIOS Menu 20) to configure the Northbridge chipset. BIOS Menu 21:NorthBridge Chipset Configuration Boots Graphics Adapter Priority [PCI/IGD] Use the Boots Graphics Adapter Priority option to select the graphics controller used as the primary boot device. Select either an integrated graphics controller (IGD) or a combination of PCI graphics controller, a PCI express (PEG) controller or an IGD.
PAGE 155
KINO-9453 Mini-ITX Motherboard PCI/IGD DEFAULT Internal Graphics Mode Select [Enable, 8MB] Use the Internal Graphic Mode Select option to specify the amount of system memory that can be used by the Internal graphics device. Disable 1MB of memory used by internal graphics device Enable, 1MB Enable, 8MB DEFAULT 8MB of memory used by internal graphics device PEG Port [Auto] Use the PEG Port option to enable or disable the PCI Express port. Auto DEFAULT The system automatically detects the PEG port.
PAGE 156
KINO-9453 Mini-ITX Motherboard Figure 6-1: Video Function Configuration DVMT Mode Select [DVMT Mode] Use the DVMT Mode Select option to select the Intel Dynamic Video Memory Technology (DVMT) operating mode. A fixed portion of graphics memory is reserved as Fixed Mode graphics memory. DVMT Mode DEFAULT Graphics memory is dynamically allocated according to the system and graphics needs. Combo Mode A fixed portion of graphics memory is reserved as graphics memory.
PAGE 157
KINO-9453 Mini-ITX Motherboard DVMT/FIXED Memory [128MB] Use the DVMT/FIXED Memory option to specify the maximum amount of memory that can be allocated as graphics memory. This option can only be configured for if DVMT Mode or Fixed Mode is selected in the DVMT Mode Select option. If Combo Mode is selected, the maximum amount of graphics memory is 128MB. Configuration options are listed below.
PAGE 158
KINO-9453 Mini-ITX Motherboard 1280x600 2048x1536 (36bits) Local Flat Panel Scaling [Auto] Use the Local Flat Panel Scaling option to select the method of scaling for the flat panel screen attached to the system. Auto DEFAULT Scaling is automatic Forced Scaling Scaling is forced Disabled Scaling is disabled 6.7.2 SouthBridge Chipset Configuration The SouthBridge Chipset Configuration menu (BIOS Menu 22) the Southbridge chipset to be configured.
PAGE 159
KINO-9453 Mini-ITX Motherboard ASF Support [Enabled] Use the ASF Support BIOS option to control the system’s ability to connect to a remote management server. The system will not communicate with a remote Disabled management server. Enabled DEFAULT The Alert Standard Format (ASF) controller is activated and can communicate with a remote management server. Audio Controller [AC`97 Audio Only] The Audio Controller option allows selection of the audio controller to use.
PAGE 160
KINO-9453 Mini-ITX Motherboard and enabled Enabled DEFAULT Disabled The on-board LAN2 controller is manually enabled The on-board LAN2 controller is manually disabled 6.8 Exit Use the Exit menu (BIOS Menu 23) to load default BIOS values, optimal failsafe values and to save configuration changes. BIOS Menu 23:Exit Save Changes and Exit Use the Save Changes and Exit option to save the changes made to the BIOS options and to exit the BIOS configuration setup program.
PAGE 161
KINO-9453 Mini-ITX Motherboard Use the Discard Changes and Exit option to exit the BIOS configuration setup program without saving the changes made to the system. Discard Changes Use the Discard Changes option to discard the changes and remain in the BIOS configuration setup program. Load Optimal Defaults Use the Load Optimal Defaults option to load the optimal default values for each of the parameters on the Setup menus. F9 key can be used for this operation.
PAGE 162
KINO-9453 Mini-ITX Motherboard Chapter 7 7 Driver Installation Page 144
PAGE 163
KINO-9453 Mini-ITX Motherboard 7.1 Available Software Drivers NOTE: The content of the CD may vary throughout the life cycle of the product and is subject to change without prior notice. You may visit the IEI website or contact technical support for the latest updates. The following drivers can be installed on the system. Chipset driver VGA driver LAN driver Installation instructions are given below. 7.2 Driver CD Auto-run All the drivers for the KINO-9453 are on the CD that came with the system.
PAGE 164
KINO-9453 Mini-ITX Motherboard Figure 7-1: Available Drivers Step 5: Select the driver to install from the list in Figure 7-1. Step 0: 7.3 Chipset Driver Installation To install the chipset driver, please follow the steps below: Step 1: Select the INF driver from the list in Figure 7-1. Step 2: A new window opens (Figure 7-2).
PAGE 165
KINO-9453 Mini-ITX Motherboard Figure 7-2: Chipset Driver Installation Program Step 3: Double click the infinst_Autol icon in Figure 7-2. Step 4: The welcome screen in Figure 7-3 appears.
PAGE 166
KINO-9453 Mini-ITX Motherboard Figure 7-3: Chipset Driver Installation Welcome Screen Step 5: Click NEXT in Figure 7-3 to continue the installation process. Step 6: The license agreement in Figure 7-4 appears.
PAGE 167
KINO-9453 Mini-ITX Motherboard Figure 7-4: Chipset Driver Installation License Agreement Step 7: Click YES to continue the setup. Step 8: The Readme file in Figure 7-5 appears.
PAGE 168
KINO-9453 Mini-ITX Motherboard Figure 7-5: Chipset Driver Readme File Information Step 9: Click NEXT in Figure 7-5 to start the driver installation. Step 10: After the driver installation process is complete, a confirmation screen (Figure 7-6) appears.
PAGE 169
KINO-9453 Mini-ITX Motherboard Figure 7-6: Chipset Driver Installation Complete 7.4 Intel Graphics Media Accelerator Driver To install the chipset driver, please follow the steps below: Step 1: Select the VGA driver from the list in Figure 7-1. Step 2: A new window opens (Figure 7-7).
PAGE 170
KINO-9453 Mini-ITX Motherboard Figure 7-7: Select the Operating System Step 3: Select the operating system from those shown in Figure 7-7. Step 4: A new window appears (Figure 7-8).
PAGE 171
KINO-9453 Mini-ITX Motherboard Figure 7-8: VGA Driver Step 5: Click the installation program icon in Figure 7-8. Step 6: The Readme information file shown in Figure 7-9 appears.
PAGE 172
KINO-9453 Mini-ITX Motherboard Figure 7-9: GMA Driver Readme File Step 7: Click NEXT to extract the GMA driver files. See Figure 7-10. Figure 7-10: GMA Driver File Extraction Step 8: The welcome screen shown in Figure 7-11 appears.
PAGE 173
KINO-9453 Mini-ITX Motherboard Figure 7-11: GMA Driver Installation Welcome Screen Step 9: To continue the installation process, click NEXT. Step 10: The license agreement in Figure 7-12 appears.
PAGE 174
KINO-9453 Mini-ITX Motherboard Figure 7-12: GMA Driver License Agreement Step 11: Click the YES in Figure 7-12 to continue. Step 12: The installation notice shown in Figure 7-13 appears. Figure 7-13: GMA Driver Installing Notice Step 13: A confirmation screen shown in Figure 7-14 appears.
PAGE 175
KINO-9453 Mini-ITX Motherboard Figure 7-14: GMA Driver Installation Complete Step 14: After selecting when to restart the computer in Figure 7-14, click FINISH. Step 0: 7.5 Broadcom LAN Driver (for GbE LAN) Installation To install the Broadcom LAN driver, please follow the steps below. Step 1: Open Windows Control Panel (Figure 7-15).
PAGE 176
KINO-9453 Mini-ITX Motherboard Figure 7-15: Access Windows Control Panel Step 2: Double click the System icon (Figure 7-16).
PAGE 177
KINO-9453 Mini-ITX Motherboard Figure 7-16: Double Click the System Icon Step 3: Double click the Device Manager tab (Figure 7-17). Figure 7-17: Double Click the Device Manager Tab Step 4: A list of system hardware devices appears (Figure 7-18).
PAGE 178
KINO-9453 Mini-ITX Motherboard Figure 7-18: Device Manager List Step 5: Double click the listed device that has question marks next to it. (This means Windows does not recognize the device). Step 6: The Device Driver Wizard appears (Figure 7-19). Click NEXT to continue.
PAGE 179
KINO-9453 Mini-ITX Motherboard Figure 7-19: Search for Suitable Driver Step 7: Select “Specify a Location” in the Locate Driver Files window (Figure 7-20). Click NEXT to continue.
PAGE 180
KINO-9453 Mini-ITX Motherboard Figure 7-20: Locate Driver Files Step 8: Select the proper OS folder under the “X:\3-LAN\BROADCOM BCM57xx Drivers” directory (Figure 7-21) in the location browsing window, where “X:\” is the system CD drive. Figure 7-21: Location Browsing Window Step 9: Click OK to continue. A driver files location menu window appears. Click NEXT to continue. The driver is installed.
PAGE 181
KINO-9453 Mini-ITX Motherboard 7.6 Realtek HD Audio Driver (ALC883) Installation To install the Realtek High Definition (HD) Audio driver, please follow the steps below. 7.6.1 BIOS Setup Step 1: Enter the BIOS setup. To do this, reboot the system and press DEL during POST. Step 2: Go to the Southbridge Configuration menu. Set the Audio Controller option to [Azalia]. See Chapter 6 for details. Step 3: Press F10 to save the changes and exit the BIOS setup. The system reboots. Step 0: 7.6.
PAGE 182
KINO-9453 Mini-ITX Motherboard Step 4: Once the WDM_R140 icon is double clicked, the contents of the installation package are extracted. See Figure 7-23.
PAGE 183
KINO-9453 Mini-ITX Motherboard Step 5: The Welcome screen appears. Click NEXT. See Figure 7-24.
PAGE 184
KINO-9453 Mini-ITX Motherboard Step 6: The driver is automatically installed. Step 7: After the driver installation process is complete, a confirmation screen shown in Figure 7-25 appears. Figure 7-25: HD Audio Driver Installation Complete Step 8: The confirmation screen shown in Figure 7-25 allows you to restart the computer immediately after the installation is complete or to restart the computer later. For the settings to take effect the computer must be restarted.
PAGE 185
KINO-9453 Mini-ITX Motherboard 7.7 Realtek AC`97 Audio Driver (ALC665) Installation To install the Realtek AC `97 audio driver, please follow the steps below. 7.7.1 BIOS Setup Step 1: Enter the BIOS setup. To do this, reboot the system and press DEL during POST. Step 2: Go to the Southbridge Configuration menu. Set the Audio Controller option to [AC`97]. See Section 6.7.2 for details. Step 3: Press F10 to save the changes and exit the BIOS setup. The system reboots. Step 0: 7.7.
PAGE 186
KINO-9453 Mini-ITX Motherboard Figure 7-26: CD 4-AUDIO\AC-KIT08R\Windows Folder Step 3: Double-click the Setup.exe file to begin the driver installation process. Step 4: Once you double click the Setup icon, the install shield wizard for the audio driver starts. See Figure 7-27. Figure 7-27: AC`97 Audio Driver Install Shield Wizard Starting Step 5: The Realtek Audio Setup prepares the install shield to guide you through the rest of the setup process. See Figure 7-24.
PAGE 187
KINO-9453 Mini-ITX Motherboard Figure 7-28: AC`97 Audio Driver Setup Preparation Step 6: After the install shield is prepared, the welcome screen shown in Figure 7-29 appears. To continue the installation process, click the “NEXT” button. The install shield starts to configure the new software as shown in Figure 7-30.
PAGE 188
KINO-9453 Mini-ITX Motherboard Figure 7-30: AC`97 Audio Driver Software Configuration Page 170
PAGE 189
KINO-9453 Mini-ITX Motherboard Step 7: At this stage the “Digital Signal Not Found” screen appears (Figure 7-31). To continue the installation process, click the “YES” button.
PAGE 190
KINO-9453 Mini-ITX Motherboard Step 8: After clicking the “YES” button in Figure 7-31, the installation of the driver begins (Figure 7-32).
PAGE 191
KINO-9453 Mini-ITX Motherboard Step 9: After the driver installation process is complete, a confirmation screen shown in Figure 7-33 appears. Figure 7-33: AC`97 Audio Driver Installation Complete Step 10: The confirmation screen shown in Figure 7-33 allows you to restart the computer immediately after the installation is complete or to restart the computer later. For the settings to take effect the computer must be restarted. Once you have decided when to restart the computer, click the “FINISH” button.
PAGE 192
KINO-9453 Mini-ITX Motherboard 7.8 Intel Matrix Storage Manager Installation To install the Intel® Matrix Storage Manager driver, please follow the steps below: Step 1: Select SATA from the list in Figure 7-1. Step 2: A new window opens (Figure 7-34). Figure 7-34: SATA RAID Driver Installation Program Step 3: Double-click the INTEL folder. Step 4: Double-click the iata62_cd.exe program icon in Figure 7-35.
PAGE 193
KINO-9453 Mini-ITX Motherboard Figure 7-35: SATA RAID Setup Program Icon Step 5: Figure 7-36 shows the InstallShield Wizard preparing to guide the user through the rest of the process.
PAGE 194
KINO-9453 Mini-ITX Motherboard Step 6: Figure 7-37 shows the Matrix Storage Manager software configuring the installation process. Figure 7-37: Matrix Storage Manager Setup Screen Step 7: Figure 7-38 shows the Matrix Storage Manager welcome screen.
PAGE 195
KINO-9453 Mini-ITX Motherboard Step 8: Click NEXT and a warning appears (Figure 7-39). Read the warning carefully and decide whether or not to continue the installation process. Figure 7-39: Matrix Storage Manager Warning Screen Step 9: Click NEXT and a license agreement appears (Figure 7-40).
PAGE 196
KINO-9453 Mini-ITX Motherboard Step 10: Read the license agreement. To accept the terms and conditions stipulated in the license agreement shown, click YES and the Readme information file shown in Figure 7-41 appears. Figure 7-41: Matrix Storage Manager Readme File Step 11: Read the Readme file information and click NEXT.
PAGE 197
KINO-9453 Mini-ITX Motherboard Step 12: After the driver installation process is complete, a confirmation screen appears (Figure 7-42). Figure 7-42: Matrix Storage Manager Setup Complete Step 13: The confirmation screen offers the option of restarting the computer now or later. For the settings to take effect, the computer must be restarted. Click FINISH to restart the computer.
PAGE 198
KINO-9453 Mini-ITX Motherboard Appendix A A BIOS Options Page 180
PAGE 199
KINO-9453 Mini-ITX Motherboard System Overview .................................................................................................................90 System Time [xx:xx:xx] .......................................................................................................91 System Date [xx/xx/xx] ........................................................................................................91 ATA/IDE Configuration [Enhanced].........................................................
PAGE 200
KINO-9453 Mini-ITX Motherboard Power Supply Mode [ATX] ................................................................................................112 Restore on AC Power Loss by IO [Power Off] ................................................................112 Resume on Ring [Disabled] ..............................................................................................112 Resume on PME# [Disabled] ............................................................................................
PAGE 201
KINO-9453 Mini-ITX Motherboard Allocate IRQ to PCI VGA [Yes]......................................................................................... 125 Palette Snooping [Disabled] ............................................................................................ 125 PCI IDE BusMaster [Enabled] .......................................................................................... 125 OffBoard PCI/ISA IDE Card [Auto]..............................................................................
PAGE 202
KINO-9453 Mini-ITX Motherboard Appendix B B DIO Interface Page 184
PAGE 203
KINO-9453 Mini-ITX Motherboard B.1 DIO Interface Introduction The DIO connector on the KINO-9453 is interfaced to GIO ports on the iTE Super I/O chipset. The DIO has both 4-bit digital inputs and 4-bit digital outputs. The digital inputs and digital outputs are generally control signals that control the on/off circuit of external devices or TTL devices. Data can be read or written to the selected address to enable the DIO functions.
PAGE 204
KINO-9453 Mini-ITX Motherboard B.3 Assembly Language Samples B.3.1 Enable the DIO Input Function The BIOS interrupt call INT 15H controls the digital I/O. An assembly program to enable digital I/O input functions is listed below. MOV AX, 6F08H Sets the digital port as input INT 15H Initiates the INT 15H BIOS call B.3.2 Enable the DIO Output Function The BIOS interrupt call INT 15H controls the digital I/O. An assembly program to enable digital I/O output functions is listed below.
PAGE 205
KINO-9453 Mini-ITX Motherboard Appendix C C Watchdog Timer Page 187
PAGE 206
KINO-9453 Mini-ITX Motherboard NOTE: The following discussion applies to DOS environment. IEI support is contacted or the IEI website visited for specific drivers for more sophisticated operating systems, e.g., Windows and Linux. The Watchdog Timer is provided to ensure that standalone systems can always recover from catastrophic conditions that cause the CPU to crash. This condition may have occurred by external EMI or a software bug.
PAGE 207
KINO-9453 Mini-ITX Motherboard NOTE: When exiting a program it is necessary to disable the Watchdog Timer, otherwise the system resets.
PAGE 208
KINO-9453 Mini-ITX Motherboard Appendix D D Address Mapping Page 190
PAGE 209
KINO-9453 Mini-ITX Motherboard D.
PAGE 210
KINO-9453 Mini-ITX Motherboard D.3 IRQ Mapping Table IRQ0 System Timer IRQ8 RTC clock IRQ1 Keyboard IRQ9 ACPI IRQ2 Available IRQ10 LAN IRQ3 COM2 IRQ11 LAN/USB2.0/SATA IRQ4 COM1 IRQ12 PS/2 mouse IRQ5 SMBus Controller IRQ13 FPU IRQ6 FDC IRQ14 Primary IDE IRQ7 Available IRQ15 Secondary IDE Table D-3: IRQ Mapping Table D.
PAGE 211
KINO-9453 Mini-ITX Motherboard Appendix E ® E Intel Matrix Storage Manager Page 193
PAGE 212
KINO-9453 Mini-ITX Motherboard E.1 Introduction The Intel® ICH7R chipset can provide data protection for serial ATA (SATA) disks via the Intel® Matrix Storage Manager using one of three fault-tolerant RAID levels: RAID 1, 5 or 10. When using two hard drives, matrix RAID allows RAID 0 and RAID 1 functions to be combined, where critical files can be stored on RAID 1, and RAID 0 can be used for non-critical items such as software.
PAGE 213
KINO-9453 Mini-ITX Motherboard CAUTION! Do not accidentally disconnect the SATA drive cables. Carefully route the cables within the chassis to avoid system down time. E.2 Features and Benefits Supports RAID levels 0, 1, 5 and 10 Supports connectivity to two or more disk drives Supported Operating Systems include: Windows XP, Windows Server 2003 and Windows Vista E.3 Accessing the Intel® Matrix Storage Manager To access the Intel® Matrix Storage Manager, please follow the steps below.
PAGE 214
KINO-9453 Mini-ITX Motherboard Step 3: Save and Exit BIOS. After the SATA support option is enabled, save and exit the BIOS. Step 4: Reboot the system. Reboot the system after saving and exiting the BIOS. Step 5: Press Ctrl+I. During the system boot process, press Ctrl+I when prompted to enter the RAID configuration software. Step 6: Configure the RAID settings. Use the Intel® Matrix Storage Manager to configure the RAID array. Brief descriptions of configuration options are given below.
PAGE 215
KINO-9453 Mini-ITX Motherboard Step 1: Select “Create RAID Volume.” Use the arrow keys to highlight Create RAID Volume and press ENTER. See Figure E-1. Figure E-1: Matrix Storage Manager Main Menu Step 2: Name the RAID volume. Enter a name for the RAID volume, or press ENTER to accept the default volume name. Upper and lower case alphabetic, numeric, space, and underscore characters are all applicable for naming an array. See Figure E-2.
PAGE 216
KINO-9453 Mini-ITX Motherboard Step 3: Choose the RAID level. Select a RAID level from the list. RAID levels include RAID 0, 1, 5 and 10. See Figure E-3. NOTE: RAID 0 and RAID1 levels require a minimum of two hard drives. RAID 10 level requires a minimum of four hard drives. RAID5 level requires a minimum of three hard drives.
PAGE 217
KINO-9453 Mini-ITX Motherboard Step 4: Select the Stripe Size. Select a stripe size from the list. See Figure E-4. Figure E-4: Select the Stripe Size Step 5: Enter the Volume Capacity. Enter the volume capacity, or press ENTER to accept the default capacity. See Figure E-5.
PAGE 218
KINO-9453 Mini-ITX Motherboard Step 6: Create the RAID Volume. Press ENTER to create the RAID volume as specified. See Figure E-6. Figure E-6: Create the RAID Volume Step 7: Create RAID Volume Verification. After reading the warning, press Y to create the RAID volume as specified, or N to return to the Create RAID Volume menu. See Figure E-7.
PAGE 219
KINO-9453 Mini-ITX Motherboard E.4.2 Deleting a RAID Volume WARNING! All data stored on the member drives of a RAID volume are destroyed during the RAID deletion process. Make sure any data to be saved has been moved or backed up before deleting a RAID volume. Step 1: Select “Delete RAID Volume.” Use the arrow keys to highlight Delete RAID Volume and press ENTER. See Figure E-8.
PAGE 220
KINO-9453 Mini-ITX Motherboard Step 2: Select RAID Volume to be Deleted. Use the arrow keys to highlight the RAID volume to be deleted and press ENTER. See Figure E-9. Figure E-9: Select RAID Volume to be Deleted Step 3: Delete Volume Verification. After reading the warning, press Y to delete the specified RAID volume, or N to return to the Delete Volume menu. See Figure E-10.
PAGE 221
KINO-9453 Mini-ITX Motherboard Step 4: Non-RAID Disks. After deleting the RAID volume, the disks belonging to the volume will be shown as non-RAID disks. See Figure E-11. Step 0: Figure E-11: Non-RAID Disks E.4.3 Resetting a Disk to Non-RAID WARNING! All data stored on the disk drive of a RAID volume is destroyed when resetting it to non-RAID. Make sure any data to be saved has been moved or backed up before resetting a disk to non-RAID.
PAGE 222
KINO-9453 Mini-ITX Motherboard Step 1: Select “Reset Disk to Non-RAID.” Use the arrow keys to highlight Reset Disk to Non-RAID and press ENTER. See Figure E-12. Figure E-12: Reset Disk to Non-RAID Menu Step 2: Select Disks to Reset. Use the arrow keys to scroll through the disk drives and press SPACE to select which drives are to be reset as non-RAID. After all the disks to be reset have been chosen, press ENTER. See Figure E-13.
PAGE 223
KINO-9453 Mini-ITX Motherboard Step 3: Reset Disk Verification. After reading the warning, press Y to reset the selected disks as non-RAID, or N to return to the Reset RAID Data menu. See Figure E-14. Figure E-14: Reset Disk Verification Step 4: Disk Drive and RAID Volume Status. After the disk drives have been reset, the Matrix Storage Manager Main menu is shown indicating the status of the RAID volumes and disk drives. See Figure E-15.
PAGE 224
KINO-9453 Mini-ITX Motherboard E.4.4 Exiting the Matrix Storage Manager Step 1: Select “Exit.” Use the arrow keys to highlight Exit and press ENTER. See Figure E-16. Figure E-16: Exit Menu Step 2: Exit Verification. Press Y to exit the Matrix Storage Manager, or N to return to the Main menu. See Figure E-17.
PAGE 225
KINO-9453 Mini-ITX Motherboard F Index Page 207
PAGE 226
KINO-9453 Mini-ITX Motherboard chipset driver................................... 146, 151 A ACPI ................................................109, 110 Advanced Power Management ....... 111, 141 airflow ........................................................75 ALC655 CODEC........................................16 anti-static precautions..........................25, 56 anti-static pad ..................................25, 56 anti-static wristband.........................25, 56 handling ................
PAGE 227
KINO-9453 Mini-ITX Motherboard CPU ...........................................................12 F compatible .............................................12 CRT monitor...............................................83 fan speed controller ...................................21 FDD......................................................... 100 D front panel ..................................................34 Front panel...................................................4 DB-15 connector.................
PAGE 228
KINO-9453 Mini-ITX Motherboard L PCIe bus ....................................................19 peripheral device cables ............................76 LCD backlight ........................................4, 37 power supply LCD voltage ...........................................5, 65 AT/ATX power select jumper .................66 LPC bus .....................................................19 processors .................................................12 LPC interface .............................
PAGE 229
KINO-9453 Mini-ITX Motherboard six-channel audio CODEC.........................16 unpacking checklist ...............................26 socket 479 CPU unpacking precautions...........................25 cooling kit ..............................................62 USB...................................... 2, 117, 118, 119 cooling kit installation ............................62 controller................................................18 installation..............................................