Page i
NANO-9452 EPIC Motherboard Revision MODEL NANO-9452 Socket 479 Intel Motherboard Revision Number Description Date of Issue 1.
Copyright COPYRIGHT NOTICE The information in this document is subject to change without prior notice in order to improve reliability, design and function and does not represent a commitment on the part of the manufacturer. In no event will the manufacturer be liable for direct, indirect, special, incidental, or consequential damages arising out of the use or inability to use the product or documentation, even if advised of the possibility of such damages.
NANO-9452 EPIC Motherboard Packing List NOTE: If any of the components listed in the checklist below are missing, please do not proceed with the installation. Contact the IEI reseller or vendor you purchased the NANO-9452 from or contact an IEI sales representative directly. To contact an IEI sales representative, please send an email to sales@iei.com.tw. The items listed below should all be included in the NANO-9452 package.
Table of Contents 1 INTRODUCTION..................................................................................................... 1 1.1 INTRODUCTION .......................................................................................................... 2 1.1.1 NANO-9452 Benefits.......................................................................................... 2 1.1.2 NANO-9452 Features ........................................................................................ 2 1.
NANO-9452 EPIC Motherboard 2.6.4 Intel® ICH7M Low Pin Count (LPC) Interface ............................................... 16 2.6.5 Intel® ICH7M PCI Interface ............................................................................ 16 2.6.6 Intel® ICH7M Real Time Clock........................................................................ 16 2.6.7 Intel® ICH7M SATA Controller........................................................................ 17 2.6.8 Intel® ICH7M USB Controller...................
4.1.2 Peripheral Interface Connectors ..................................................................... 31 4.1.3 External Interface Panel Connectors............................................................... 32 4.2 INTERNAL PERIPHERAL CONNECTORS ...................................................................... 33 4.2.1 +12V ATX Power Supply Connector ............................................................... 33 4.2.2 +5V ATX Power Supply Connector ..........................................
NANO-9452 EPIC Motherboard 5.3 CPU, CPU COOLING KIT AND DIMM INSTALLATION ............................................. 69 5.3.1 Socket 479 CPU Installation............................................................................ 69 5.3.2 Cooling Kit CF-479B-RS Installation.............................................................. 72 5.3.3 SODIMM Installation ...................................................................................... 74 5.3.4 CF Card Installation...........................
6.3.2 IDE Configuration ......................................................................................... 104 6.3.2.1 IDE Master, IDE Slave ........................................................................... 105 6.3.3 Super IO Configuration................................................................................... 111 6.3.4 Hardware Health Configuration.....................................................................116 6.3.5 ACPI Configuration ...................................
NANO-9452 EPIC Motherboard A BIOS OPTIONS .................................................................................................... 203 B DIO INTERFACE................................................................................................. 209 B.1 DIO INTERFACE INTRODUCTION ........................................................................... 210 B.2 DIO CONNECTOR PINOUTS ................................................................................... 210 B.
List of Figures Figure 1-1: NANO-9452 Overview [Front View] ...........................................................................3 Figure 1-2: NANO-9452 Overview [Rear View].............................................................................4 Figure 2-1: NANO-9452 Dimensions (mm) ...................................................................................8 Figure 2-2: External Interface Panel Dimensions (mm) ..............................................................
NANO-9452 EPIC Motherboard Figure 4-26: COM1 Serial Port Connector..................................................................................62 Figure 4-27: VGA Connector........................................................................................................63 Figure 5-1: Make sure the CPU socket retention screw is unlocked ......................................70 Figure 5-2: Lock the CPU Socket Retention Screw...................................................................
Figure 7-12: GMA Driver Installation Welcome Screen.......................................................... 177 Figure 7-13: GMA Driver License Agreement ......................................................................... 178 Figure 7-14: GMA Driver Installing Notice............................................................................... 178 Figure 7-15: GMA Driver Installation Complete ......................................................................
NANO-9452 EPIC Motherboard List of Tables Table 1-1: Technical Specifications ..............................................................................................6 Table 2-1: Processor Features ....................................................................................................10 Table 2-2: Supported Processors ...............................................................................................11 Table 2-3: Supported HDD Specifications...................................
Table 4-24: LAN Pinouts...............................................................................................................61 Table 4-25: RJ-45 Ethernet Connector LEDs .............................................................................61 Table 4-26: COM 1 Pinouts...........................................................................................................62 Table 4-27: USB Port Pinouts .........................................................................................
NANO-9452 EPIC Motherboard BIOS Menus Menu 1: Main .............................................................................................................................. 100 Menu 2: Advanced ..................................................................................................................... 102 Menu 3: CPU Configuration...................................................................................................... 103 Menu 4: IDE Configuration ................................
Glossary AC ’97 Audio Codec 97 ACPI Advanced Configuration and HDD Hard Disk Drive Power Interface IDE Integrated Data Electronics APM Advanced Power Management I/O Input/Output ARMD ATAPI Removable Media Device ICH4 I/O Controller Hub 4 ASKIR Shift Keyed Infrared L1 Cache Level 1 Cache ATA Advanced Technology L2 Cache Level 2 Cache Attachments LCD Liquid Crystal Display BIOS Basic Input/Output System LPT Parallel Port Connector CFII Compact Flash Type 2 LVDS Low Voltage Dif
NANO-9452 EPIC Motherboard THIS PAGE IS INTENTIONALLY LEFT BLANK Page xix
NANO-9452 EPIC Motherboard Chapter 1 1 Introduction Page 1
NANO-9452 EPIC Motherboard 1.1 Introduction The NANO-9452 EPIC form factor CPU card is a Socket 479 Intel® Core Duo or Socket 479 Intel® Core Solo CPU platform. The NANO-9452 has a maximum front side bus (FSB) frequency of 667MHz and comes with a VGA interface and dual PCI Express (PCIe) Gigabit Ethernet (GbE). The NANO-9452 supports up to two, second-generation serial ATA (SATA) hard disk drives (HDD) with maximum transfer rates of 3Gb/s and up to six USB 2.0 devices.
NANO-9452 EPIC Motherboard dual-channel LVDS EPIC form factor RoHS compliant Supports AT and ATX power supplies 1.2 NANO-9452 Overview 1.2.1 NANO-9452 Overview Photo The NANO-9452 has a wide variety of internal and external peripheral connectors. The peripheral connectors are connected to devices including PCI-104 devices, mini PCIe devices, storage devices, display devices and parallel communications devices.
NANO-9452 EPIC Motherboard Figure 1-2: NANO-9452 Overview [Rear View] 1.2.
NANO-9452 EPIC Motherboard 2 x Serial port connectors (internal COM 3 and COM 4 RS-232) 2 x USB connectors The NANO-9452 has the following external peripheral interface connectors on the board rear panel 2 x Ethernet connectors 1 x PS/2 keyboard or mouse connector 1 x Serial port connector 2 x USB port connectors 1 x VGA connector The NANO-9452 has the following on-board jumpers: Clear CMOS LCD voltage selector CF card setting COM 2 port mode setting PC104+ VIO selector PC104+ SERIRQ# support 1.2.
NANO-9452 EPIC Motherboard Specification NANO-9452 One 200-pin SO-DIMM socket supports one 533MHz or Memory 667MHz DDR2 SO-DIMM with a maximum capacity of 1GB CRT: Integrated in the Intel® 945GM to support CRT Display TV-Out: S-Video and composite output LVDS: Dual channel 18-bit LVDS LCD panel BIOS AMI BIOS Audio 7.1 channel or 5.
NANO-9452 EPIC Motherboard Chapter 2 2 Detailed Specifications Page 7
NANO-9452 EPIC Motherboard 2.1 Overview This chapter describes the specifications and on-board features of the NANO-9452 in detail. 2.2 Dimensions 2.2.1 Board Dimensions The dimensions of the board are listed below: Length: 165mm Width: 115mm Figure 2-1: NANO-9452 Dimensions (mm) 2.2.2 External Interface Panel Dimensions External peripheral interface connector panel dimensions are shown in Figure 2-2.
NANO-9452 EPIC Motherboard Figure 2-2: External Interface Panel Dimensions (mm) 2.3 Data Flow Figure 2-3 shows the data flow between the two on-board chipsets and other components installed on the motherboard and described in the following sections of this chapter.
NANO-9452 EPIC Motherboard 2.4 Compatible Processors 2.4.1 Compatible Processor Overview The NANO-9452 supports the following socket 479 processors: ® Intel ® Intel ® Intel Core™2 Duo Mobile processors Core™ Duo processors Core™ Solo processors All three of the above processors communicate with the Intel ® 945GM northbridge chipset through a 667MHz front side bus (FSB). Features of the supported processors are listed in Table 2-1.
NANO-9452 EPIC Motherboard Family sSpec# CPU Speed Processor # Bus Speed Mfg Tech Stepping Cache Size Core™ Duo SL8VT 2 GHz T2500 667 MHz 65 nm C0 2 MB SL9DN 1.66 GHz T2300E 667 MHz 65 nm C0 2 MB SL92X 1.83 GHz T1400 667 MHz 65 nm C0 2 MB Core™ Solo Table 2-2: Supported Processors 2.5 Intel® 945GM Northbridge Chipset 2.5.1 Intel® 945GM Overview The Intel® 945GM northbridge chipset has the Generation 3.
NANO-9452 EPIC Motherboard DDR2 only (DO NOT install a DDR SO-DIMM) Single-channel or dual-channel Capacities of 256MB, 512MB or 1GB Transfer speeds of 533MHz, or 667MHz 64-bit wide channel The memory socket is shown in Figure 2-4. Figure 2-4: 200-pin SO-DIMM Socket 2.5.3 Intel® 945GM Integrated Graphics The Intel® 945GM northbridge chipset has an Intel® Gen. 3.
NANO-9452 EPIC Motherboard 2.5.3.1 Intel® 945GM Analog CRT Support A DB-15 VGA connector on the external peripheral interface connector panel is interfaced to the Intel® 945GM graphics engine. The Intel® 945GM internal graphics engine, with an integrated 400MHz RAMDAC and hot plug CRT support, supports analog CRT monitors up to QXGA. 2.5.3.2 Intel® 945GM LVDS Support A 30-pin LVDS crimp connector is interfaced to the Intel® 945GM graphics engine.
NANO-9452 EPIC Motherboard Two SDVO ports supported o o o o o SDVO is muxed onto the PCIe pins DVI 1.0 support for external digital monitor Only Downstream HDCP support Supports TV and DVD formats Display hot plug support 2.5.4 Intel® 945GM Direct Media Interface (DMI) Intel® 945GM northbridge GMCH is connected to the Intel® ICH7M Southbridge Chipset through the chip-to-chip Direct Media Interface (DMI).
NANO-9452 EPIC Motherboard controllers and one EHCI controller Complies with System Management Bus (SMBus) Specification, Version 2.0 Supports Audio Codec ’97 (AC’97) Revision 2.3 Supports Intel® High Definition Audio Contains Low Pin Count (LPC) interface Supports Firmware Hub (FWH) interface 2.6.2 Intel® ICH7M Audio Codec ’97 Controller The Audio Codec ’97 (AC’97) controller integrated into the ICH7M complies with AC’97 Component Specification, Version 2.3.
NANO-9452 EPIC Motherboard Specification Ultra ATA/100 Ultra ATA/66 Ultra ATA/100 PIO Mode 0–4 0–4 0–4 PIO Max Transfer Rate 16.6 MB/s 16.6 MB/s 16.6 MB/s DMA/UDMA designation UDMA 3 - 4 UDMA 3 – 4 UDMA 2 DMA/UDMA Max Transfer 100MB/s 66MB/s 33MB/s Controller Interface 5V 5V 5V Table 2-3: Supported HDD Specifications 2.6.4 Intel® ICH7M Low Pin Count (LPC) Interface The ICH7M LPC interface complies with the LPC 1.1 specifications.
NANO-9452 EPIC Motherboard 2.6.7 Intel® ICH7M SATA Controller The integrated SATA controller on the ICH7M southbridge supports two SATA drives on the NANO-9452 with independent DMA operations. SATA controller specifications are listed below. Supports two SATA drives Supports 3Gb/s data transfer speeds Supports Serial ATA Specification, Revision 1.0a 2.6.8 Intel® ICH7M USB Controller Up to six high-speed, full-speed or low-speed USB devices are supported by the ICH7M on the NANO-9452. High-speed USB 2.
NANO-9452 EPIC Motherboard PCIe v1.0a 10/100/1000BASE-T full/half-duplex MAC Wake on LAN support meeting the ACPI requirements Statistics for SNMP MIB II, Ethernet-like MIB, and Ethernet MIB (802.3z, clause 30) Serial EEPROM or serial flash support JTAG support 2.7.3 Mini PCIe The Mini PCIe socket supports Mini PCIe cards that are compliant with PCI Express Base Specification, Revision 1.0a. The Mini PCIe cards are easily installed into the socket. Mini PCIe cards are 30mm wide, 50.
NANO-9452 EPIC Motherboard 2.8.3 Super I/O chipset The iTE IT8712F Super I/O chipset is connected to the ICH6 southbridge through the LPC bus. The iTE IT8712F is an LPC interface-based Super I/O device that comes with Environment Controller integration.
NANO-9452 EPIC Motherboard Another two chipsets connected to the LPC bus provided connectivity to another two serial port connectors (COM3 and COM4). 2.8.3.3 Super I/O Enhanced Hardware Monitor The Super I/O Enhanced Hardware Monitor monitors three thermal inputs, VBAT internally, and eight voltage monitor inputs. These hardware parameters are reported in the BIOS and can be read from the BIOS Hardware Health Configuration menu. 2.8.3.
NANO-9452 EPIC Motherboard Supports mouse double-click and/or mouse move power on events 2.9 Environmental and Power Specifications 2.9.1 System Monitoring Three thermal inputs on the NANO-9152 Super I/O Enhanced Hardware Monitor monitor the following temperatures: System temperature Power temperature CPU temperature Eight voltage inputs on the NANO-9152 Super I/O Enhanced Hardware Monitor monitor the following voltages: Vcore +2.5V +3.3V +5.0V +12.0V DDR Vtt +1.
NANO-9452 EPIC Motherboard 2.9.2 Operating Temperature and Temperature Control The maximum and minimum operating temperatures for the NANO-9152 are listed below. Minimum Operating Temperature: 0ºC (32°F) Maximum Operating Temperature: 60°C (140°F) A cooling fan and heat sink must be installed on the CPU. Thermal paste must be smeared on the lower side of the heat sink before it is mounted on the CPU.
NANO-9452 EPIC Motherboard Chapter 3 3 Unpacking Page 23
NANO-9452 EPIC Motherboard 3.1 Anti-static Precautions WARNING: Failure to take ESD precautions during the installation of the NANO-9452 may result in permanent damage to the NANO-9452 and severe injury to the user. Electrostatic discharge (ESD) can cause serious damage to electronic components, including the NANO-9452. Dry climates are especially susceptible to ESD.
NANO-9452 EPIC Motherboard 3.3 Unpacking Checklist NOTE: If some of the components listed in the checklist below are missing, please do not proceed with the installation. Contact the IEI reseller or vendor you purchased the NANO-9452 from or contact an IEI sales representative directly. To contact an IEI sales representative, please send an email to sales@iei.com.tw. 3.3.
NANO-9452 EPIC Motherboard 1 KB/MS cable (P/N: 32000-000138-RS) 2 SATA cables (P/N: 32000-062800-RS) 1 SATA power cable (P/N: 32100-088600-RS) 1 Mini jumper Pack 1 Quick Installation Guide 1 Utility CD Table 3-1: Package List Contents Page 26
NANO-9452 EPIC Motherboard 3.3.2 Optional Items NOTE: The items listed in this section are optional items that must be ordered separately. Please contact your NANO-9452 vendor, distributor or reseller for more information or, contact iEi directly by sending an email to sales@iei.com.tw. The following optional items are available for the NANO-9452.
NANO-9452 EPIC Motherboard Quantity Item and Part Number 1 LPT cable (P/N: 32200-000017-RS) 1 RS-232 cable (P/N: 32200-000049-RS) 1 7.1 Channel HD audio kit with Realtek ALC883 supporting dual audio streams (P/N: AC-KIT-883HD) 1 5.
NANO-9452 EPIC Motherboard Chapter 4 4 Connector Pinouts Page 29
NANO-9452 EPIC Motherboard 4.1 Peripheral Interface Connectors Section 4.1.2 shows peripheral interface connector locations. Section 4.1.2 lists all the peripheral interface connectors seen in Section 4.1.2. 4.1.1 NANO-9452 Layout Figure 4-1 shows the on-board peripheral connectors, rear panel peripheral connectors and on-board jumpers.
NANO-9452 EPIC Motherboard Figure 4-2: Connector and Jumper Locations (Solder Side) 4.1.2 Peripheral Interface Connectors Table 4-1 shows a list of the peripheral interface connectors on the WAFER-LX. Detailed descriptions of these connectors can be found below.
NANO-9452 EPIC Motherboard Connector Type Label Front panel connector 8-pin header F_PANEL1 IDE Interface connector 44-pin header IDE1 Infrared connector 5-pin header IR1 Inverter power connector 5-pin header INVERTER1 Keyboard and mouse connector 6-pin wafer KB1 LVDS connector 30-pin crimp LVDS1 Parallel port connector 26-pin header LPT1 PCI-104 slot 104-pin slot PC104_PLUS1 PCIe Mini Card slot 52-pin slot CN4 Serial ATA (SATA) connector 7-pin SATA connector SATA1 Serial AT
NANO-9452 EPIC Motherboard Connector Type Label Ethernet connector RJ-45 LAN1 Ethernet connector RJ-45 LAN2 Keyboard and mouse connector PS/2 connector KB_MS1 RS-232 serial port connector Male DB-9 COM1 USB port USB port USB_C45 VGA port connector Female DB-15 VGA1 Table 4-2: Rear Panel Connectors 4.2 Internal Peripheral Connectors Internal peripheral connectors are found on the motherboard and are only accessible when the motherboard is outside of the chassis.
NANO-9452 EPIC Motherboard Figure 4-3: +12V ATX Power Connector Location PIN NO. DESCRIPTION 1 GND 2 GND 3 +12V 4 +12V Table 4-3: +12V ATX Power Connector Pinouts 4.2.2 +5V ATX Power Supply Connector CN Label: CN3 CN Type: 2-pin Wafer (1 x 2) CN Location: See Figure 4-4 CN Pinouts: See Table 4-4 The 2-pin +5V ATX power supply connector is connected to a +5V ATX power supply.
NANO-9452 EPIC Motherboard Figure 4-4: +5V ATX Power Connector Location PIN NO. DESCRIPTION 1 GND 2 GND 3 +12V 4 +12V Table 4-4: +5V ATX Power Connector Pinouts 4.2.3 ATX Power Supply Enable Connector CN Label: ATXCTL1 CN Type: 3-pin wafer (1x3) CN Location: See Figure 4-5 CN Pinouts: See Table 4-5 The ATX power supply enable connector enables the NANO-9452 to be connected to an ATX power supply. In default mode, the NANO-9452 can only us an AT power supply.
NANO-9452 EPIC Motherboard Figure 4-5: ATX Power Supply Enable Connector Location PIN NO. DESCRIPTION 1 GND 2 PS-ON 3 +5V Standby Table 4-5: ATX Power Supply Enable Connector Pinouts 4.2.
NANO-9452 EPIC Motherboard Figure 4-6: Audio Connector Pinouts (10-pin) PIN NO. DESCRIPTION PIN NO. DESCRIPTION 1 AC97_SYNC 2 AC97_BITCLK 3 AC97_SDOUT 4 AC97_PCBEEP 5 AC97_SDIN 6 AC97_RST# 7 AC97_VCC 8 AC97_GND 9 AC97_12V Table 4-6: Audio Connector Pinouts (10-pin) 4.2.
NANO-9452 EPIC Motherboard Figure 4-7: CF Card Socket Location Page 38
NANO-9452 EPIC Motherboard PIN NO. DESCRIPTION PIN NO.
NANO-9452 EPIC Motherboard 4.2.6 Digital Input/Output (DIO) Connector CN Label: DIO1 CN Type: 10-pin header (2x5) CN Location: See Figure 4-8 CN Pinouts: See Table 4-8 The digital input/output connector is managed through a Super I/O chip. The DIO connector pins are user programmable. Figure 4-8: DIO Connector Connector Locations PIN NO. DESCRIPTION PIN NO.
NANO-9452 EPIC Motherboard CN Location: See Figure 4-9 CN Pinouts: See Table 4-9 The cooling fan connector provides a 12V, 500mA current to a system cooling fan. The connector has a "rotation" pin to get rotation signals from fans and notify the system so the system BIOS can recognize the fan speed. Please note that only specified fans can issue the rotation signals. Figure 4-9: +12V Fan Connector Location PIN NO.
NANO-9452 EPIC Motherboard CN Location: See Figure 4-10 CN Pinouts: See Table 4-10 The front panel connector connects to external switches and indicators to monitor and controls the motherboard.
NANO-9452 EPIC Motherboard 4.2.9 IDE Connector(44-pin) CN Label: KB1 CN Type: 44-pin header (2x22) CN Location: See Figure 4-11 CN Pinouts: See Table 4-11 One 44-pin IDE device connector on the NANO-9452 supports connectivity to two hard disk drives.
NANO-9452 EPIC Motherboard PIN NO. DESCRIPTION PIN NO.
NANO-9452 EPIC Motherboard The infrared interface connector supports both Serial Infrared (SIR) and Amplitude Shift Key Infrared (ASKIR) interfaces. Figure 4-12: Infrared Connector Pinout Locations PIN NO. DESCRIPTION 1 VCC 2 NC 3 IR-RX 4 GND 5 IR-TX Table 4-12: Infrared Connector Pinouts 4.2.
NANO-9452 EPIC Motherboard Figure 4-13: Keyboard/Mouse Connector Location PIN NO. DESCRIPTION 1 +5V KB DATA 2 MS DATA 3 MS CLK 4 KB DATA 5 KB CLK 6 GROUND Table 4-13: Keyboard/Mouse Connector Pinouts 4.2.12 LVDS LCD Connector CN Label: LVDS1 CN Type: 30-pin crimp (2x10) CN Location: See Figure 4-14 CN Pinouts: See Table 4-14 The 30-pin LVDS LCD connector can be connected to single channel or dual channel, 18-bit or 36-bit LVDS panel.
NANO-9452 EPIC Motherboard Figure 4-14: LVDS LCD Connector Pinout Locations PIN NO. DESCRIPTION PIN NO.
NANO-9452 EPIC Motherboard 4.2.13 Mini PCIe Socket CN Label: CN4 CN Type: 26-pin box header CN Location: See CN Pinouts: See The 52-pin mini PCIe socket supports the latest PCIe extension cards such as wireless LAN cards and other compatible devices.
NANO-9452 EPIC Motherboard PIN NO. DESCRIPTION PIN NO. DESCRIPTION 1 PCIE_WAKE# 2 VCC3 3 N/C 4 GND 5 N/C 6 1.5V 7 CLKREQ# 8 LFRAME# 9 GND 10 LAD3 11 CLK- 12 LAD2 13 CLK+ 14 LAD1 15 GND 16 LAD0 17 PCIRST# 18 GND 19 LPC 20 VCC3 21 GND 22 PCIRST# 23 PERN2 24 3VDual 25 PERP2 26 GND 27 GND 28 1.
NANO-9452 EPIC Motherboard 4.2.14 Parallel Port Connector CN Label: LPT1 CN Type: 26-pin box header CN Location: See Figure 4-16 CN Pinouts: See Table 4-16 The 26-pin parallel port connector connects to a parallel port connector interface or some other parallel port device such as a printer. Figure 4-16: Parallel Port Connector Location PIN NO. DESCRIPTION PIN NO.
NANO-9452 EPIC Motherboard PIN NO. DESCRIPTION PIN NO. DESCRIPTION 17 PRINTER SELECT LN# 18 GROUND 19 GROUND 20 GROUND 21 GROUND 22 GROUND 23 GROUND 24 GROUND 25 GROUND 26 NC Table 4-16: Parallel Port Connector Pinouts 4.2.15 PCI-104 Slot CN Label: PC104_PLUS1 CN Type: 120-pin PCI-104 slot CN Location: See Figure 4-17 CN Pinouts: See Table 4-17 The PCI-104 slot enables a PCI-104 compatible expansion module to be connected to the board.
NANO-9452 EPIC Motherboard Figure 4-17: PCI-104 Slot Location Page 52
NANO-9452 EPIC Motherboard Pin No. Column A Column B Column C Column D 1 GND/5V TBD1 5V AD00 2 VI/O1 AD02 AD01 +5V 3 AD05 GND AD04 AD03 4 C/BE0# AD07 GND AD06 5 GND AD09 AD08 GND 6 AD11 VI/O2 AD10 M66EN 7 AD14 AD13 GND AD12 8 +3.3V C/BE1# AD15 +3.3V 9 SERR# GND SB0# PAR 10 GND PERR# +3.3V SDONE 11 STOP# +3.3V LOCK# GND 12 +3.3V TRDY# GND DEVSEL# 13 FRAME# GND IRDY# +3.3V 14 GND AD16 +3.3V C/BE2# 15 AD18 +3.
NANO-9452 EPIC Motherboard Pin No. Column A Column B Column C Column D 30 -12V TBD2 TBD GND/3.3V Table 4-17: PCI-104 Slot Connector Pinouts 4.2.16 SATA Drive Connectors CN Label: SATA1 and SATA2 CN Type: 7-pin SATA drive connectors CN Location: See Figure 4-18 CN Pinouts: See Table 4-18 The two SATA drive connectors are each connected to a first generation SATA drive. First generation SATA drives transfer data at speeds as high as 150Mb/s.
NANO-9452 EPIC Motherboard PIN NO. DESCRIPTION 4 GND 5 RX- 6 RX+ 7 GND Table 4-18: SATA Drive Connector Pinouts 4.2.17 Serial Port Connector (COM 2)(RS-232, RS-422 or RS-485) CN Label: COM2 CN Type: 14-pin header (2x7) CN Location: See Figure 4-19 CN Pinouts: See Table 4-19 The 14-pin serial port connector connects to the COM 2 serial communications channels. COM 2 is a multi function channel.
NANO-9452 EPIC Motherboard PIN NO. DESCRIPTION PIN NO. DESCRIPTION 7 DTR 8 NRI2 9 GND 10 GND 11 TXD485+ 12 TXD485# 13 RXD485+ 14 RXD485# Table 4-19: RS-232/RS-485 Serial Port Connector Pinouts 4.2.18 Serial Port Connector (COM 3 and COM 4) CN Label: COM3 and COM4 CN Type: 10-pin header (2x5) CN Location: See Figure 4-20 CN Pinouts: See Table 4-20 The 10-pin serial port connector provides a second RS-232 serial communications channel.
NANO-9452 EPIC Motherboard PIN NO. DESCRIPTION PIN NO. DESCRIPTION 5 Transmit Data (TXD) 6 Clear To Send (CTS) 7 Data Terminal Ready (DTR) 8 Ring Indicator (RI) 9 Ground (GND) 10 NC Table 4-20: COM3 and COM4 4.2.19 TV Out Connector CN Label: TV1 CN Type: 6-pin header (2x3) CN Location: See Figure 4-21 CN Pinouts: See Table 4-21 The 2x3 pin TV out connector connects to a TV output by using an S-Video or RCA connector.
NANO-9452 EPIC Motherboard S-Video Connector PIN NO. DESCRIPTION PIN NO. DESCRIPTION 1 GND 2 AGREEN_Y 3 GND 4 ARED_C RCA Connector (only video signal) 5 GND 6 ABLUE_CVBS Table 4-21: TV Port Connector Pinouts 4.2.20 USB Connectors (Internal) CN Label: USB01 and USB23 CN Type: 8-pin header (2x4) CN Location: See Figure 4-22 CN Pinouts: See Table 4-22 The 2x4 USB pin connectors each provide connectivity to two USB 1.1 or two USB 2.0 ports.
NANO-9452 EPIC Motherboard PIN NO. DESCRIPTION PIN NO. DESCRIPTION 1 VCC 2 GND 3 DATAN- 4 DATA1M- 5 DATAN+ 6 DATAM+ 7 GND 8 VCC Table 4-22: USB Port Connector Pinouts 4.3 External Peripheral Interface Connector Panel Figure 4-23 shows the NANO-9452 rear panel. The NANO-9452 rear panel consists of two RJ-45 Ethernet connectors, a PS/2 keyboard connector a USB port and a VGA connector. These connectors are accessible when the NANO-9452 is installed in a chassis.
NANO-9452 EPIC Motherboard Figure 4-24: PS/2 Pinouts PIN DESCRIPTION 1 KEYBOARD DATA 2 MOUSE DATA 3 GND 4 VCC 5 KEYBOARD CLOCK 6 MOUSE CLOCK Table 4-23: Mini-DIN 6 PS/2 Connector Pinouts 4.3.2 LAN Connectors CN Label: LAN1 and LAN2 CN Type: RJ-45 CN Location: See Figure 4-23 CN Pinouts: See Table 4-24 The NANO-9452 is equipped with two built-in GbE Ethernet controllers. The controllers can connect to the LAN through two RJ-45 LAN connectors.
NANO-9452 EPIC Motherboard PIN DESCRIPTION PIN DESCRIPTION 1 TXA+ 5 TXC- 2 TXA- 9 TXB- 3 TXB+ 10 TXD+ 4 TXC+ 11 TXD- Table 4-24: LAN Pinouts Figure 4-25: RJ-45 Ethernet Connector The RJ-45 Ethernet connector has two status LEDs, one green and one yellow. The green LED indicates activity on the port and the yellow LED indicates the port is linked. See Table 4-25. STATUS DESCRIPTION STATUS DESCRIPTION GREEN Activity YELLOW Linked Table 4-25: RJ-45 Ethernet Connector LEDs 4.3.
NANO-9452 EPIC Motherboard Figure 4-26: COM1 Serial Port Connector COM1 pinouts are shown below. PIN Description PIN Description 1 DCD1 6 DSR1 2 RXD1 7 RTS1 3 TXD1 8 CTS1 4 DTR1 9 RI1 5 GROUND 10 Table 4-26: COM 1 Pinouts 4.3.4 USB Connector CN Label: USB_C45 CN Type: USB port CN Location: See Figure 4-23 CN Pinouts: See Table 4-27 The NANO-9452 has a one external USB 2.0 port. The port connects to both USB 2.0 and USB 1.1 devices.
NANO-9452 EPIC Motherboard PIN NO. DESCRIPTION PIN NO. DESCRIPTION 1 USBV3L 5V 2 GND 3 USBP4N 4 USBP5P 5 USBP4P 6 USBP5N 7 GND 8 USBV3L 5V Table 4-27: USB Port Pinouts 4.3.5 VGA Connector CN Label: VGA1 CN Type: 15-pin Female CN Location: See Figure 4-23 CN Pinouts: See Figure 4-27 and Table 4-28 The NANO-9452 has a single 15-pin female connector for connectivity to standard display devices.
NANO-9452 EPIC Motherboard PIN DESCRIPTION 13 HSYNC 15 DDCCLK PIN 14 DESCRIPTION VSYNC Table 4-28: VGA Connector Pinouts Page 64
NANO-9452 EPIC Motherboard Chapter 5 5 Installation Page 65
NANO-9452 EPIC Motherboard 5.1 Anti-static Precautions WARNING: Failure to take ESD precautions during the installation of the NANO-9452 may result in permanent damage to the NANO-9452 and severe injury to the user. Electrostatic discharge (ESD) can cause serious damage to electronic components, including the NANO-9452. Dry climates are especially susceptible to ESD.
NANO-9452 EPIC Motherboard 5.2 Installation Considerations NOTE: The following installation notices and installation considerations should be read and understood before the NANO-9452 is installed. All installation notices pertaining to the installation of the NANO-9452 should be strictly adhered to. Failing to adhere to these precautions may lead to severe damage of the NANO-9452 and injury to the person installing the motherboard. 5.2.
NANO-9452 EPIC Motherboard o When working with the NANO-9452, make sure that it is disconnected from all power supplies and that no electricity is being fed into the system. Before and during the installation of the NANO-9452 DO NOT: Remove any of the stickers on the PCB board. These stickers are required for warranty validation. Use the product before verifying all the cables and power connectors are properly connected.
NANO-9452 EPIC Motherboard o o o Keyboard Mouse RS-232 serial communications device 5.3 CPU, CPU Cooling Kit and DIMM Installation WARNING: A CPU should never be turned on without the specified cooling kit being installed. If the cooling kit (heat sink and fan) is not properly installed and the system turned on, permanent damage to the CPU, NANO-9452 and other electronic components attached to the system may be incurred. Running a CPU without a cooling kit may also result in injury to the user.
NANO-9452 EPIC Motherboard WARNING: When handling the CPU, only hold it on the sides. DO NOT touch the pins at the bottom of the CPU. Step 1: Unlock the CPU retention screw. When shipped, the retention screw of the CPU socket should be in the unlocked position. If it is not in the unlocked position, use a screwdriver to unlock the screw. See Figure 5-1. Figure 5-1: Make sure the CPU socket retention screw is unlocked Step 2: Inspect the CPU socket.
NANO-9452 EPIC Motherboard Step 5: Align the CPU pins. Carefully align the CPU pins with the holes in the CPU socket. Step 6: Insert the CPU. Gently insert the CPU into the socket. If the CPU pins are properly aligned, the CPU should slide into the CPU socket smoothly. Step 7: Lock the retention screw. Rotate the retention screw into the locked position. See Figure 5-2.
NANO-9452 EPIC Motherboard 5.3.2 Cooling Kit CF-479B-RS Installation Figure 5-3: IEI CF-479B-RS Cooling Kit An IEI Socket 479 CPU cooling kit can be purchased separately. The cooling kit comprises a CPU heat sink and a cooling fan. WARNING: Do not wipe off (accidentally or otherwise) the pre-sprayed layer of thermal paste on the bottom of the [Fan model#] heat sink. The thermal paste between the CPU and the heat sink is important for optimum heat dissipation.
NANO-9452 EPIC Motherboard Figure 5-4: Cooling Kit Support Bracket Step 4: Tighten the screws. Use a screwdriver to tighten the four screws. Tighten each nut a few turns at a time and do not over-tighten the screws. Step 5: Connect the fan cable. Connect the cooling kit fan cable to the fan connector on the motherboard. Carefully route the cable and avoid heat generating chips and fan blades. See Figure 5-5.
NANO-9452 EPIC Motherboard 5.3.3 SODIMM Installation WARNING: Using incorrectly specified SODIMM may cause permanently damage the NANO-9452. Please make sure the purchased SODIMM complies with the memory specifications of the NANO-9452. SODIMM specifications compliant with the NANO-9452 are listed in Chapter 2. To install a SODIMM into a SODIMM socket, please follow the steps below and refer Figure 5-6. Figure 5-6: SODIMM Installation Step 1: Locate the SODIMM socket.
NANO-9452 EPIC Motherboard Step 4: Open the SODIMM socket arms. Gently pull the arms of the SODIMM socket out and push the rear of the SODIMM down. (See Figure 5-6) Step 5: Secure the SODIMM. Release the arms on the SODIMM socket. They clip into place and secure the SODIMM in the socket.Step 0: 5.3.4 CF Card Installation NOTE: The NANO-9452 can support both CF Type I cards and CF Type II cards. For the complete specifications of the supported CF cards please refer to Chapter 2.
NANO-9452 EPIC Motherboard Figure 5-7: CF Card Installation Page 76
NANO-9452 EPIC Motherboard 5.4 Jumper Settings NOTE: A jumper is a metal bridge used to close an electrical circuit. It consists of two or three metal pins and a small metal clip (often protected by a plastic cover) that slides over the pins to connect them. To CLOSE/SHORT a jumper means connecting the pins of the jumper with the plastic clip and to OPEN a jumper means removing the Figure 5-8: Jumper Locations plastic clip from a jumper.
NANO-9452 EPIC Motherboard 5.4.1 CF Card Setup Jumper Label: JCF1 Jumper Type: 3-pin header Jumper Settings: See Table 5-2 Jumper Location: See Figure 5-9 The CF Card Setup jumper sets the CF Type I card or CF Type II cards as either the slave device or the master device. CF Card Setup jumper settings are shown in Table 5-2. AT Power Select Description Short 1-2 Slave Short 2-3 Master Default Table 5-2: CF Card Setup Jumper Settings The CF Card Setup jumper location is shown in Figure 5-9.
NANO-9452 EPIC Motherboard 5.4.2 Clear CMOS Jumper Jumper Label: J_CMOS1 Jumper Type: 3-pin header Jumper Settings: See Table 5-3 Jumper Location: See Figure 5-10 If the NANO-9452 fails to boot due to improper BIOS settings, the clear CMOS jumper clears the CMOS data and resets the system BIOS information. To do this, use the jumper cap to close pins 2 and 3 for a few seconds then reinstall the jumper clip back to pins 1 and 2.
NANO-9452 EPIC Motherboard Figure 5-10: Clear CMOS Jumper 5.4.3 COM 2 Function Select Jumper Jumper Label: JP1 Jumper Type: 3-pin header Jumper Settings: See Table 5-4 Jumper Location: See Figure 5-11 The COM 2 Function Select jumper sets the communication protocol used by the second serial communications port (COM 2) as RS-232, RS-422 or RS-485. The COM 2 Function Select settings are shown in Figure 5-11.
NANO-9452 EPIC Motherboard Figure 5-11: COM 2 Function Select Jumper Location 5.4.4 LVDS Voltage Selection WARNING: Permanent damage to the screen and NANO-9452 may occur if the wrong voltage is selected with this jumper. Please refer to the user guide that cam with the monitor to select the correct voltage. Jumper Label: J_LVDS1 Jumper Type: 3-pin header Jumper Settings: See Table 5-5 Jumper Location: See Figure 5-12 The LVDS Voltage Selection jumper allows the LVDS screen voltage to be set.
NANO-9452 EPIC Motherboard AT Power Select Description Short 1-2 +3V LVDS Short 2-3 +5V LVDS Default Table 5-5: LVDS Voltage Selection Jumper Settings The LVDS Voltage Selection jumper location. is shown in Figure 5-12. Figure 5-12: LVDS Voltage Selection Jumper Pinout Locations 5.4.5 PCI-104 VIO Selector Jumper Jumper Label: JP2 Jumper Type: 3-pin header Jumper Settings: See Table 5-6 Jumper Location: See Figure 5-13 The PCI-104 VIO Selector jumper allows the PCI-104 voltage to be set.
NANO-9452 EPIC Motherboard AT Power Select Description Short 1-2 VCC Short 2-3 VCC3 Default Table 5-6: PCI-104 VIO Selector Jumper Settings The PCI-104 VIO Selector jumper location. is shown in Figure 5-12. Figure 5-13: PCI-104 VIO Selector Jumper Pinout Locations 5.4.
NANO-9452 EPIC Motherboard Jumper Location: See Figure 5-14 The PCI-104 SERIRQ# Support jumper enables or disable SERIRQ# on the PCI-104. The PCI-104 SERIRQ# Support jumper settings are shown in Table 5-5. AT Power Select Description Open None Short Support Default Table 5-7: PCI-104 SERIRQ# Support Jumper Settings The PCI-104 SERIRQ# Support jumper location is shown in Figure 5-12. Figure 5-14: PCI-104 SERIRQ# Support Jumper Pinout Locations 5.
NANO-9452 EPIC Motherboard 5.5.1 Airflow WARNING: Airflow is critical to the cooling of the CPU and other onboard components. The chassis in which the NANO-9452 must have air vents to allow cool air to move into the system and hot air to move out. The NANO-9452 must be installed in a chassis with ventilation holes on the sides allowing airflow to travel through the heat sink surface.
NANO-9452 EPIC Motherboard Quantity Type 1 IDE Cable 1 KB/MS cable 2 SATA drive cables 1 SATA drive power cable Table 5-8: IEI Provided Cables Optional cables are listed below: USB cable TV out cable RS-232/422/485 cable LPT cable RS-232 cable 7.1 channel audio kit 5.1 channel audio kit 5.6.2 IDE Cable Connection The IDE flat cable connects to the NANO-9452 to one or two IDE devices. To connect an IDE HDD to the NANO-9452 please follow the instructions below. Step 1: Locate the IDE connector.
NANO-9452 EPIC Motherboard Figure 5-15: IDE Cable Connection Step 3: Connect the cable to an IDE device. Connect the two connectors on the other side of the cable to one or two IDE devices.
NANO-9452 EPIC Motherboard 5.6.3 5.1 Channel Audio Kit Installation NOTE: This is an optional item that must be ordered separately. For further information please contact the nearest NANO-9452 distributor, reseller or vendor or contact an iEi sales representative directly. Send any queries to sales@iei.com.tw. The optional 5.1 channel audio kit connects to the 10-pin audio connector on the NANO-9452. The audio kit consists of three audio jacks. One audio jack, Mic In, connects to a microphone.
NANO-9452 EPIC Motherboard Figure 5-16: 5.1 Channel Audio Kit Step 4: Mount the audio kit onto the chassis. Once the audio kit is connected to the NANO-9452, secure the audio kit bracket to the system chassis. Step 5: Connect the audio devices. Connect one speaker to the line-in audio jack, one speaker to the line-out audio jack and a microphone to the mic-in audio jack. Step 6: Install the driver. If the 5.1 channel audio kit is used, the ALC655 Realtek codec driver must be installed.
NANO-9452 EPIC Motherboard 5.6.4 7.1 Channel Audio Kit Installation NOTE: This is an optional item that must be ordered separately. For further information please contact the nearest NANO-9452 distributor, reseller or vendor or contact an iEi sales representative directly. Send any queries to sales@iei.com.tw. The optional 7.1 channel audio kit connects to the 10-pin audio connector on the NANO-9452. The audio kit consists of five audio jacks. One audio jack, Mic In, connects to a microphone.
NANO-9452 EPIC Motherboard Figure 5-17: 5.1 Channel Audio Kit Step 4: Mount the audio kit onto the chassis. Once the audio kit is connected to the NANO-9452, secure the audio kit bracket to the system chassis. Step 5: Connect the audio devices. Connect one speaker to the line-in audio jack, one speaker to the line-out audio jack and a microphone to the mic-in audio jack. Step 6: Install the driver. If the 5.1 channel audio kit is used, the ALC655 Realtek codec driver must be installed.
NANO-9452 EPIC Motherboard in Chapter 3. Step 2: Insert the cable connector. Press the clip on the connector at the end of the SATA cable and insert the cable connector into the onboard SATA drive connector. See Figure 5-18. Figure 5-18: SATA Drive Cable Connection Step 3: Connect the cable to the SATA disk. Connect the connector on the other end of the cable to the connector at the back of the SATA drive. See Figure 5-19. Step 4: Connect the SATA power cable.
NANO-9452 EPIC Motherboard back of the SATA drive. See Figure 5-19. Step 0: Figure 5-19: SATA Power Drive Connection 5.7 External Peripheral Interface Connection The following external peripheral devices can be connected to the external peripheral interface connectors.
NANO-9452 EPIC Motherboard To install these devices, connect the corresponding cable connector from the actual device to the corresponding NANO-9452 external peripheral interface connector making sure the pins are properly aligned. 5.7.1 VGA Monitor Connection The NANO-9452 has a single female DB-15 connector on the external peripheral interface panel. The DB-15 connector is connected to a CRT or VGA monitor. To connect a monitor to the NANO-9452, please follow the instructions below.
NANO-9452 EPIC Motherboard monitor to the external interface by tightening the two retention screws on either side of the connector. Step 0: 5.7.2 PS/2 Keyboard/Mouse Connection The NANO-9452 has a single PS/2 connector on the external peripheral interface panel. The PS/2 connector is connected to a keyboard and a mouse through the keyboard and mouse cable that was shipped with the system. To connect a keyboard and mouse to the NANO-9452, please follow the instructions below.
NANO-9452 EPIC Motherboard Figure 5-21: PS/2 Connector Step 4: Connect the keyboard and mouse. Once the cable is connected to the NANO-9452 PS/2 connector. Connect the keyboard and mouse to their respective PS/2 connector on the keyboard and mouse cable. Step 0: CAUTION: The keyboard and mouse cable has a specific connector for the mouse and a specific connector for the keyboard. The cable is marked. Please make sure the devices are connected to the correct connector.
NANO-9452 EPIC Motherboard Chapter 6 6 AMI BIOS Page 97
NANO-9452 EPIC Motherboard 6.1 Introduction A licensed copy of AMI BIOS is preprogrammed into the ROM BIOS. The BIOS setup program allows users to modify the basic system configuration. This chapter describes how to access the BIOS setup program and the configuration options that may be changed. 6.1.1 Starting Setup The AMI BIOS is activated when the computer is turned on. The setup program can be activated in one of two ways. 1. Press the DELETE key as soon as the system is turned on or 2.
NANO-9452 EPIC Motherboard Key Function F1 key General help, only for Status Page Setup Menu and Option Page Setup Menu F2 /F3 key Change color from total 16 colors. F2 to select color forward. F10 key Save all the CMOS changes, only for Main Menu Table 6-1: BIOS Navigation Keys 6.1.3 Getting Help When F1 is pressed a small help window describing the appropriate keys to use and the possible selections for the highlighted item appears. To exit the Help Window press ESC or the F1 key again. 6.1.
NANO-9452 EPIC Motherboard 6.2 Main The Main BIOS menu (BIOS Menu 1) appears when the BIOS Setup program is entered. The Main menu gives an overview of the basic system information. BIOS Menu 1: Main System Overview The System Overview lists a brief summary of different system components. The fields in System Overview cannot be changed.
NANO-9452 EPIC Motherboard Processor: Displays auto-detected CPU specifications o o o Type: Names the currently installed processor Speed: Lists the processor speed Count: The number of CPUs on the motherboard System Memory: Displays the auto-detected system memory. o Size: Lists memory size The System Overview field also has two user configurable fields: System Time [xx:xx:xx] Use the System Time option to set the system time. Manually enter the hours, minutes and seconds.
NANO-9452 EPIC Motherboard APM Configuration (See Section 6.3.6) MPS Configuration (see Section 6.3.6) Remote Access Configuration (see Section 6.3.8) USB Configuration (see Section 6.3.8) BIOS Menu 2: Advanced 6.3.1 CPU Configuration Use the CPU Configuration menu (BIOS Menu 3) to view detailed CPU specifications and configure the CPU.
NANO-9452 EPIC Motherboard BIOS Menu 3: CPU Configuration The CPU Configuration menu (BIOS Menu 3) lists the following CPU details: Manufacturer: Lists the name of the CPU manufacturer Brand String: Lists the brand name of the CPU being used Frequency: Lists the CPU processing speed FSB Speed: Lists the FSB speed Cache L1: Lists the CPU L1 cache size Cache L2: Lists the CPU L2 cache size The following CPU Configuration menu items can be configured. Intel ® SpeedStep ™ tech.
NANO-9452 EPIC Motherboard 6.3.2 IDE Configuration Use the IDE Configuration menu (BIOS Menu 4) to change and/or set the configuration of the IDE devices installed in the system.
NANO-9452 EPIC Motherboard SATA Only PATA Pri, SATA Sec (Default) PATA Pri., PATA Sec IDE Master and IDE Slave When entering setup, BIOS auto detects the presence of IDE devices. BIOS displays the status of the auto detected IDE devices.
NANO-9452 EPIC Motherboard BIOS Menu 5: IDE Master and IDE Slave Configuration Auto-Detected Drive Parameters The “grayed-out” items in the left frame are IDE disk drive parameters automatically detected from the firmware of the selected IDE disk drive. The drive parameters are listed as follows: Device: Lists the device type (e.g. hard disk, CD-ROM etc.) Type: Indicates the type of devices a user can manually select Vendor: Lists the device manufacturer Size: List the storage capacity of the device.
NANO-9452 EPIC Motherboard interrupt if block mode is not used. Block mode allows transfers of up to 64 KB per interrupt. PIO Mode: Indicates the PIO mode of the installed device. Async DMA: Indicates the highest Asynchronous DMA Mode that is supported. Ultra DMA: Indicates the highest Synchronous DMA Mode that is supported. S.M.A.R.T.: Indicates whether or not the Self-Monitoring Analysis and Reporting Technology protocol is supported. 32Bit Data Transfer: Enables 32-bit data transfer.
NANO-9452 EPIC Motherboard LBA/Large Mode [Auto] Use the LBA/Large Mode option to disable or enable BIOS to auto detects LBA (Logical Block Addressing). LBA is a method of addressing data on a disk drive. In LBA mode, the maximum drive capacity is 137 GB. BIOS is prevented from using the LBA mode control on Disabled the specified channel. Auto DEFAULT BIOS auto detects the LBA mode control on the specified channel.
NANO-9452 EPIC Motherboard 0 PIO mode 0 selected with a maximum transfer rate of 3.3MBps 1 PIO mode 1 selected with a maximum transfer rate of 5.2MBps 2 PIO mode 2 selected with a maximum transfer rate of 8.3MBps 3 PIO mode 3 selected with a maximum transfer rate of 11.1MBps 4 PIO mode 4 selected with a maximum transfer rate of 16.6MBps (This setting generally works with all hard disk drives manufactured after 1999.
NANO-9452 EPIC Motherboard Ultra DMA mode 0 selected with a maximum data transfer UDMA1 rate of 16.6MBps Ultra DMA mode 1 selected with a maximum data transfer UDMA1 rate of 25MBps Ultra DMA mode 2 selected with a maximum data transfer UDMA2 rate of 33.3MBps Ultra DMA mode 3 selected with a maximum data transfer UDMA3 rate of 44MBps (To use this mode, it is required that an 80-conductor ATA cable is used.) Ultra DMA mode 4 selected with a maximum data transfer UDMA4 rate of 66.
NANO-9452 EPIC Motherboard Prevents the BIOS from using 32-bit data transfers. Disabled Enabled DEFAULT Allows BIOS to use 32-bit data transfers on supported hard disk drives. 6.3.3 Super IO Configuration Use the Super IO Configuration menu (BIOS Menu 6) to set or change the configurations for the FDD controllers, parallel ports and serial ports.
NANO-9452 EPIC Motherboard OnBoard Floppy Controller [Enabled] Use the OnBoard Floppy Controller to enable or disable the floppy controller. If a floppy disk is not being used in the system, disabling this option frees up system resources that can be redirected elsewhere in the system.
NANO-9452 EPIC Motherboard Serial Port1 Mode [Normal] Use the Serial Port1 Mode option to select the transmitting and receiving mode for the first serial port. Normal (Default) Serial Port 1 mode is normal IrDA Serial Port 1 mode is IrDA ASK IR Serial Port 1 mode is ASK IR Serial Port2 Address [2F8/IRQ3] Use the Serial Port2 Address option to select the Serial Port 2 base address.
NANO-9452 EPIC Motherboard Disabled DEFAULT No base address is assigned to the Parallel Port 378 Parallel Port I/O port address is 378 278 Parallel Port I/O port address is 278 3BC Parallel Port I/O port address is 3BC Parallel Port Mode [Normal] Use the Parallel Port Mode option to select the mode the parallel port operates in. Normal DEFAULT The normal parallel port mode is the standard mode for parallel port operation. Bi-directional Parallel port outputs are 8-bits long.
NANO-9452 EPIC Motherboard Parallel Port IRQ [IRQ7] Use the Parallel Port IRQ option to set the parallel port interrupt address.
NANO-9452 EPIC Motherboard 2E8 DEFAULT Serial port 4 I/O port address is 2E8 Serial port 4 I/O port address is 2E0 2E0 Serial Port4 IRQ [10] Use the Serial Port4 IRQ option to select the interrupt address for serial port 4. 3 DEFAULT Serial port 4 IRQ address is 9 9 10 11 Serial port 4 IRQ address is 3 DEFAULT Serial port 4 IRQ address is 10 Serial port 4 IRQ address is 11 6.3.
NANO-9452 EPIC Motherboard BIOS Menu 7: Hardware Health Configuration CPU FAN Mode Setting [Full On Mode] Use the CPU FAN Mode Setting option to configure the second fan. Full On Mode Automatic mode DEFAULT Fan is on all the time Fan is off when the temperature is low enough. Parameters must be set by the user. PWM Manual mode Pulse width modulation set manually When the CPU FAN Mode Setting option is in the Automatic Mode, the following parameters can be set.
NANO-9452 EPIC Motherboard Temperature 3 Limit of OFF Temperature 3 Limit of Start Temperature 3 Limit of Full Fan 3 Start PWM Slope PWM 3 When the CPU FAN Mode Setting option is in the PWM Manual Mode, the following parameters can be set. Fan 3 PWM control Temperature 3 Limit of OFF [000] WARNING: Setting this value too high may cause the fan to stop when the CPU is at a high temperature and therefore cause the system to be damaged.
NANO-9452 EPIC Motherboard Temperature 3 Limit of Start [020] WARNING: Setting this value too high may cause the fan to start only when the CPU is at a high temperature and therefore cause the system to be damaged. The Temperature 3 Limit of Start option can only be set if the CPU FAN Mode Setting option is set to Automatic Mode. Use the Temperature 3 Limit of Start option to select the CPU temperature at which the cooling fan should automatically turn on.
NANO-9452 EPIC Motherboard speed. To select a value, select the Temperature 3 Limit of Full option and enter a decimal number between 000 and 127. The temperature range is specified below. Minimum Value: 0°C Maximum Value: 127°C Fan 3 Start PWM [070] The Fan 3 Start PWM option can only be set if the CPU FAN Mode Setting option is set to Automatic Mode.
NANO-9452 EPIC Motherboard Fan 3 PWM Control [070] The Fan 3 PWM Control option can only be set if the CPU FAN Mode Setting option is set to Manual Mode. Use the Fan 3 PWM Control option to select PWM duty cycle control. The PWM duty cycle specifies the width of the modulated pulse. A high value ensures a wide pulse and a low value ensures a narrow pulse. To select a value, select the Fan 3 PWM Control option and enter a decimal number between 000 and 127.
NANO-9452 EPIC Motherboard 6.3.5 ACPI Configuration The ACPI Configuration menu (BIOS Menu 8) configures the Advanced Configuration and Power Interface (ACPI) and Power Management (APM) options. BIOS Menu 8: ACPI Configuration ACPI Aware O/S [Yes] Use the ACPI Aware O/S option to enable the system to configure ACPI power saving options. ACPI can only be implemented if the system OS complies with the ACPI standard. Windows 98, Windows 2000, and Windows XP all comply with ACPI.
NANO-9452 EPIC Motherboard Yes DEFAULT Enables the ACPI support for the operating system. This selection should be enabled if the OS does support ACPI 6.3.5.1 General ACPI Configuration Use the General ACPI Configuration menu (BIOS Menu 9) to select the ACPI state when the system is suspended. BIOS Menu 9: General ACPI Configuration [Advanced\ ACPI Configuration] Suspend Mode [S1(POS)] Use the Suspend Mode option to specify the sleep state the system enters when it is not being used.
NANO-9452 EPIC Motherboard The system enters a S3(STR) sleep state. The CPU has S3 (STR) no power; RAM is in slow refresh; the power supply is in a reduced power mode. The BIOS automatically selects a sleep state for the Auto system. Repost Video on S3 Resume [No] Use the Repost Video on S3 Resume to determine whether the VGA BIOS post will be invoked after the system is roused from an S3 (STR) suspend state. No Yes DEFAULT The VGA BIOS post is not invoked The VGA BIOS post is invoked 6.3.
NANO-9452 EPIC Motherboard BIOS Menu 10:Advanced Power Management Configuration Power Management/APM [Enabled] Use the Power Management/APM BIOS option to enable access to the advanced power management features. If this option is disabled, the only other option on the screen is the Power Button Mode.
NANO-9452 EPIC Motherboard Restore on AC Power Loss [Power Off] Use the Restore on AC Power Loss BIOS option to specify what state the system returns to if there is a sudden loss of power to the system. The system remains turned off Power Off Power On (Default) The system turns on The system returns to its previous state. If it was on, it Last State turns itself on. If it was off, it remains off. Power Button Mode [On/Off] Use the Power Button Mode BIOS to specify how the power button functions.
NANO-9452 EPIC Motherboard Disabled (Default) Wake event not generated by PCI PME controller activity Wake event generated by PCI PME controller activity Enabled Resume On RTC Alarm [Disabled] Use the Resume On RTC Alarm option to specify the time the system should be roused from a suspended state.
NANO-9452 EPIC Motherboard BIOS Menu 11: MPS Configuration MPS Revision [1.4] Use the Multiprocessor Specification (MPS) for OS option to specify the MPS version to be used. MPS version 1.1 is used 1.1 1.4 DEFAULT MPS version 1.4 is used 6.3.8 Remote Access Configuration Use the Remote Access Configuration menu (BIOS Menu 12) to configure remote access parameters.
NANO-9452 EPIC Motherboard allows a remote host running a terminal program to display and configure the BIOS settings. BIOS Menu 12: Remote Access Configuration [Advanced] Remote Access [Disabled] Use the Remote Access option to enable or disable access to the remote functionalities of the system. Disabled Enabled DEFAULT Remote access is disabled.
NANO-9452 EPIC Motherboard Serial Port Mode Flow Control Redirection after BIOS POST Terminal Type VT-UTF8 Combo Key Support These configuration options are discussed below. Serial Port Number [COM1] Use the Serial Port Number option allows to select the serial port used for remote access. COM1 DEFAULT COM2 System is remotely accessed through COM1 System is remotely accessed through COM2 NOTE: Make sure the selected COM port is enabled through the Super I/O configuration menu.
NANO-9452 EPIC Motherboard 09600 8,n,1 NOTE: Identical baud rate setting musts be set on the host (a management computer running a terminal software) and the slave Flow Control [None] Use the Flow Control option to report the flow control method for the console redirection application.
NANO-9452 EPIC Motherboard ANSI DEFAULT The target terminal type is ANSI VT100 The target terminal type is VT100 VT-UTF8 The target terminal type is VT-UTF8 VT-UTF8 Combo Key Support [Disabled] Use the VT-UFT8 Combo Key Support option to enable additional keys that are not provided by VT100 for the PC 101 keyboard. The VT100 Terminal Definition is the standard convention used to configure and conduct emergency management tasks with UNIX-based servers.
NANO-9452 EPIC Motherboard BIOS Menu 13: USB Configuration USB Function [6 USB ports] Use the USB Function BIOS option to enable or disable a specified number of USB ports. If only two USB ports are being used, disabling the remaining six USB frees up system resources that can be redirected elsewehere.
NANO-9452 EPIC Motherboard USB 2.0 Controller [Enabled] Use the USB 2.0 Controller BIOS option to enable or disable the USB 2.0 controller USB 2.0 controller disabled Disabled Enabled DEFAULT USB 2.0 controller enabled Legacy USB Support [Enabled] Use the Legacy USB Support BIOS option to enable USB mouse and USB keyboard support.
NANO-9452 EPIC Motherboard Systems with OSes that do not support EHCI can Disabled use the EHCI handoff functionality. Enabled DEFAULT Systems with OSes that do not support EHCI cannot use the EHCI handoff functionality. 6.4 PCI/PnP Use the PCI/PnP menu (BIOS Menu 13) to configure advanced PCI and PnP settings. WARNING: Setting wrong values for the BIOS selections in the PCIPnP BIOS menu may cause the system to malfunction.
NANO-9452 EPIC Motherboard BIOS Menu 14: PCI/PnP Configuration Clear NVRAM [No] Use the Clear NVRAM option to specify if the NVRAM (Non-Volatile RAM) is cleared when the power is turned off. No DEFAULT System does not clear NVRAM during system boot System clears NVRAM during system boot Yes Plug & Play O/S [No] Use the Plug & Play O/S BIOS option to specify whether system plug and play devices are configured by the operating system or the BIOS.
NANO-9452 EPIC Motherboard devices in the system. This setting allows the operating system to change the Yes interrupt, I/O, and DMA settings. Set this option if the system is running Plug and Play aware operating systems. PCI Latency Timer [64] Use the PCI Latency Timer option to specify the PCI latency time. The latency time is measured in units of PCI clock cycles for the PCI device latency timer register.
NANO-9452 EPIC Motherboard snooping to be enabled, this option should be disabled. No/Enab PCI devices are informed that an ISA based Graphics led device is installed in the system so the ISA based Graphics card functions correctly. This does not necessarily indicate a physical ISA adapter card. The graphics chipset can be mounted on a PCI card. Always check with the adapter card manual first, before modifying the default settings in the BIOS.
NANO-9452 EPIC Motherboard PCI Slot 3 is selected as the location of the OffBoard PCI Slot 3 PCI IDE adapter card. Only select this slot if the adapter card is installed in PCI Slot 3. PCI Slot 4 is selected as the location of the OffBoard PCI Slot 4 PCI IDE adapter card. Only select this slot if the adapter card is installed in PCI Slot 4. PCI Slot 5 is selected as the location of the OffBoard PCI Slot 5 PCI IDE adapter card. Only select this slot if the adapter card is installed in PCI Slot 5.
NANO-9452 EPIC Motherboard IRQ 11 IRQ 14 IRQ 15 DMA Channel# [Available] Use the DMA Channel# option to assign a specific DMA channel to a particular PCI/PnP device.
NANO-9452 EPIC Motherboard Use the Boot menu (BIOS Menu 15) to configure system boot options. BIOS Menu 15: Boot 6.5.1 Boot Settings Configuration Use the Boot Settings Configuration menu (BIOS Menu 15) to configure advanced system boot options.
NANO-9452 EPIC Motherboard BIOS Menu 16: Boot Settings Configuration Quick Boot [Enabled] Use the Quick Boot BIOS option to make the computer speed up the boot process. No POST procedures are skipped Disabled Enabled DEFAULT Some POST procedures are skipped to decrease the system boot time Quiet Boot [Disabled] Use the Quiet Boot BIOS option to select the screen display when the system boots.
NANO-9452 EPIC Motherboard OEM Logo displayed instead of POST messages Enabled AddOn ROM Display Mode [Force BIOS] Use the AddOn ROM Display Mode option to allow add-on ROM (read-only memory) messages to be displayed. Force BIOS DEFAULT The system forces third party BIOS to display during system boot. The system displays normal information during Keep Current system boot. Bootup Num-Lock [On] Use the Bootup Num-Lock BIOS option to specify if the number lock setting must be modified during boot up.
NANO-9452 EPIC Motherboard PS/2 mouse support is disabled and prevented from Disabled using system resources. Enabled DEFAULT Allows the system to use a PS/2 mouse. The system auto-adjusts PS/2 mouse support. Auto Giga LAN Boot Support [Disabled] Use the Giga LAN Boot Support option to enable the system to be booted from a remote system. Disabled (Default) Cannot be booted from a remote system through the LAN Enabled (Default) Can be booted from a remote system through the LAN 6.5.
NANO-9452 EPIC Motherboard BIOS Menu 17: Boot Device Priority Settings Page 145
NANO-9452 EPIC Motherboard 6.5.3 Hard Disk Drives Use the Hard Disk Drives menu to specify the boot sequence of the available HDDs. When the menu is opened, the HDDs connected to the system are listed as shown below: 1st Drive [HDD: PM-(part number)] 2nd Drive [HDD: PS-(part number)] 3rd Drive [HDD: SM-(part number)] 4th Drive [HDD: SM-(part number)] NOTE: Only the drives connected to the system are shown. For example, if only two HDDs are connected only “1st Drive” and “2nd Drive” are listed.
NANO-9452 EPIC Motherboard BIOS Menu 18: Hard Disk Drives Page 147
NANO-9452 EPIC Motherboard 6.6 Security Use the Security menu (BIOS Menu 19) to set system and user passwords. BIOS Menu 19: Security Change Supervisor Password Use the Change Supervisor Password to set or change a supervisor password. The default for this option is Not Installed. If a supervisor password must be installed, select this field and enter the password. After the password has been added, Install appears next to Change Supervisor Password.
NANO-9452 EPIC Motherboard Change User Password Use the Change User Password to set or change a user password. The default for this option is Not Installed. If a user password must be installed, select this field and enter the password. After the password has been added, Install appears next to Change User Password. 6.7 Chipset Use the Chipset menu (BIOS Menu 20) to access the NorthBridge and SouthBridge configuration menus.
NANO-9452 EPIC Motherboard BIOS Menu 20: Chipset 6.7.1 NorthBridge Configuration Use the NorthBridge Configuration menu (BIOS Menu 20) to configure the northbridge chipset.
NANO-9452 EPIC Motherboard BIOS Menu 21:NorthBridge Chipset Configuration DRAM Frequency [Auto] Use the DRAM Frequency option to specify the DRAM frequency or allow the system to automatically detect the DRAM frequency.
NANO-9452 EPIC Motherboard Use the Configure DRAM Timing by SPD option to determine if the system uses the SPD (Serial Presence Detect) EEPROM to configure the DRAM timing. The SPD EEPROM contains all necessary DIMM specifications including the speed of the individual components such as CAS and bank cycle time as well as valid settings for the module and the manufacturer's code. The SPD enables the BIOS to read the spec sheet of the DIMMs on boot-up and then adjust the memory timing parameters accordingly.
NANO-9452 EPIC Motherboard strobe) signal. A pause is required between the RAS signal and the CAS signal to ensure the memory is correctly addressed.
NANO-9452 EPIC Motherboard 8 DRAM Clocks 9 DRAM Clocks 10 DRAM Clocks 11 DRAM Clocks 12 DRAM Clocks 13 DRAM Clocks 14 DRAM Clocks 15 DRAM Clocks DEFAULT DRAM CAS# Latency [By SPD] Use the DRAM CAS# Latency option to set the CAS (Column Address Strobe) latency. The CAS latency is the number of clock cycles (or Ticks, denoted with T) between the receipt of a "read" command and when the RAM chip actually starts reading. The BIOS options are as follows: By SPD (Default) 2T 2.
NANO-9452 EPIC Motherboard Boots Graphics Adapter [PEG/PCI] Use the Boots Graphics Adapter option to select the graphics controller used as the primary boot device. Select either an integrated graphics controller (IGD) or a combination of PCI graphics controller, a PCI express (PEG) controller or an IGD.
NANO-9452 EPIC Motherboard Figure 6-1: Video Function Configuration DVMT Mode Select [DVMT Mode] Use the DVMT Mode Select option to select the Intel Dynamic Video Memory Technology (DVMT) operating mode. A fixed portion of graphics memory is reserved as Fixed Mode graphics memory. DVMT Mode DEFAULT Graphics memory is dynamically allocated according to the system and graphics needs. Combo Mode A fixed portion of graphics memory is reserved as graphics memory.
NANO-9452 EPIC Motherboard DVMT/FIXED Memory Use the DVMT/FIXED Memory option to specify the maximum amount of memory that can be allocated as graphics memory. This option can only be configured for if DVMT Mode or Fixed Mode is selected in the DVMT Mode Select option. If Combo Mode is selected, the maximum amount of graphics memory is 128MB. Configuration options are listed below.
NANO-9452 EPIC Motherboard Type 8 Type 9 Local Flat Panel Scaling [Auto] Use the Local Flat Panel Scaling option to select the method of scaling for the flat panel screen attached to the system. Auto DEFAULT Scaling is automatic Forced Scaling Scaling is forced Disabled Scaling is disabled TV Connector [Auto] Use the TC Connector option to select the connector that is used to connect the system to the television. The configuration options are listed below.
NANO-9452 EPIC Motherboard odd lines and the second field presents the even lines. In progressive scanning, the image is refreshed from top to bottom, one line after the other.
NANO-9452 EPIC Motherboard BIOS Menu 22:SouthBridge Chipset Configuration Audio Controller [AC`97 Audio] The Audio Controller option allows selection of the audio controller to use. DEFAULT Azalia The Intel® High Definition Audio controller is enabled AC`97 Audio The on-board AC’97 controller is enabled All Disabled All audio controllers are disabled OnBoard LAN1 [Auto] The OnBoard LAN1 option enables or disables the on-board LAN1.
NANO-9452 EPIC Motherboard and enabled Enabled The on-board LAN1 controller is manually enabled Disabled The on-board LAN1 controller is manually disabled On-board LAN2 [Auto] The On-board LAN2 option enables or disables the on-board LAN2.
NANO-9452 EPIC Motherboard BIOS Menu 23:Exit Save Changes and Exit Use the Save Changes and Exit option to save the changes made to the BIOS options and to exit the BIOS configuration setup program. Discard Changes and Exit Use the Discard Changes and Exit option to exit the BIOS configuration setup program without saving the changes made to the system. Discard Changes Use the Discard Changes option to discard the changes and remain in the BIOS configuration setup program.
NANO-9452 EPIC Motherboard Load Optimal Defaults Use the Load Optimal Defaults option to load the optimal default values for each of the parameters on the Setup menus. F9 key can be used for this operation. Load Failsafe Defaults Use the Load Failsafe Defaults option to load failsafe default values for each of the parameters on the Setup menus. F8 key can be used for this operation.
NANO-9452 EPIC Motherboard THIS PAGE IS INTENTIONALLY LEFT BLANK Page 164
NANO-9452 EPIC Motherboard Chapter 7 7 Driver Installation Page 165
NANO-9452 EPIC Motherboard 7.1 Available Software Drivers NOTE: The content of the CD may vary throughout the life cycle of the product and is subject to change without prior notice. You may visit the IEI website or contact technical support for the latest updates. The following drivers can be installed on the system. Chipset driver VGA driver LAN driver Installation instructions are given below. 7.2 Driver CD Auto-run All the drivers for the NANO-9452 are on the CD that came with the system.
NANO-9452 EPIC Motherboard Figure 7-1: Introduction Screen Step 4: A new screen with a list of available drivers appears (Figure 7-2).
NANO-9452 EPIC Motherboard Figure 7-2: Available Drivers Step 5: Select the driver to install from the list in Figure 7-2. Step 0: 7.3 Chipset Driver Installation To install the chipset driver, please follow the steps below: Step 1: Select the INF driver from the list in Figure 7-2. Step 2: A new window opens (Figure 7-3).
NANO-9452 EPIC Motherboard Figure 7-3: Chipset Driver Installation Program Step 3: Double click the infinst_Autol icon in Figure 7-3. Step 4: The welcome screen in Figure 7-4 appears.
NANO-9452 EPIC Motherboard Figure 7-4: Chipset Driver Installation Welcome Screen Step 5: Click NEXT in Figure 7-4 to continue the installation process. Step 6: The license agreement in Figure 7-5 appears.
NANO-9452 EPIC Motherboard Figure 7-5: Chipset Driver Installation License Agreement Step 7: Click YES to continue the setup. Step 8: The Readme file in Figure 7-6 appears.
NANO-9452 EPIC Motherboard Figure 7-6: Chipset Driver Readme File Information Step 9: Click NEXT in Figure 7-6 to start the driver installation. Step 10: After the driver installation process is complete, a confirmation screen (Figure 7-7) appears.
NANO-9452 EPIC Motherboard Figure 7-7: Chipset Driver Installation Complete 7.4 Intel Graphics Media Accelerator Driver To install the chipset driver, please follow the steps below: Step 1: Select the VGA driver from the list in Figure 7-2. Step 2: A new window opens (Figure 7-8).
NANO-9452 EPIC Motherboard Figure 7-8: Select the Operating System Step 3: Select the operating system from those shown in Figure 7-8. Step 4: A new window appears (Figure 7-9).
NANO-9452 EPIC Motherboard Figure 7-9: VGA Driver Step 5: Click the installation program icon in Figure 7-9. Step 6: The Readme information file shown in Figure 7-10 appears.
NANO-9452 EPIC Motherboard Figure 7-10: GMA Driver Readme File Step 7: Click NEXT to extract the GMA driver files. See Figure 7-11. Figure 7-11: GMA Driver File Extraction Step 8: The welcome screen shown in Figure 7-12 appears.
NANO-9452 EPIC Motherboard Figure 7-12: GMA Driver Installation Welcome Screen Step 9: To continue the installation process, click NEXT. Step 10: The license agreement in Figure 7-13 appears.
NANO-9452 EPIC Motherboard Figure 7-13: GMA Driver License Agreement Step 11: Click the YES in Figure 7-13 to continue. Step 12: The installation notice shown in Figure 7-14 appears. Figure 7-14: GMA Driver Installing Notice Step 13: A confirmation screen shown in Figure 7-15 appears.
NANO-9452 EPIC Motherboard Figure 7-15: GMA Driver Installation Complete Step 14: After selecting when to restart the computer in Figure 7-15, click FINISH. Step 0: 7.5 Broadcom LAN Driver (for GbE LAN) Installation To install the Broadcom LAN driver, please follow the steps below. Step 1: Open Windows Control Panel (Figure 7-16).
NANO-9452 EPIC Motherboard Figure 7-16: Access Windows Control Panel Step 2: Double click the System icon (Figure 7-17).
NANO-9452 EPIC Motherboard Figure 7-17: Double Click the System Icon Step 3: Double click the Device Manager tab (Figure 7-18). Figure 7-18: Double Click the Device Manager Tab Step 4: A list of system hardware devices appears (Figure 7-19).
NANO-9452 EPIC Motherboard Figure 7-19: Device Manager List Step 5: Double click the listed device that has question marks next to it. (This means Windows does not recognize the device). Step 6: The Device Driver Wizard appears (Figure 7-20). Click NEXT to continue.
NANO-9452 EPIC Motherboard Figure 7-20: Search for Suitable Driver Step 7: Select “Specify a Location” in the Locate Driver Files window (Figure 7-21). Click NEXT to continue.
NANO-9452 EPIC Motherboard Figure 7-21: Locate Driver Files Step 8: Select the proper OS folder under the “X:\3-LAN\BROADCOM BCM57xx Drivers” directory (Figure 7-22) in the location browsing window, where “X:\” is the system CD drive. Figure 7-22: Location Browsing Window Step 9: Click OK to continue. A driver files location menu window appears. Click NEXT to continue. The driver is installed.
NANO-9452 EPIC Motherboard 7.6 Realtek HD Audio Driver (ALC883) Installation To install the Realtek High Definition (HD) Audio driver, please follow the steps below. 7.6.1 BIOS Setup Step 1: Enter the BIOS setup. To do this, reboot the system and press DEL during POST. Step 2: Go to the Southbridge Configuration menu. Set the Audio Controller option to [Azalia]. See Chapter 6 for details. Step 3: Press F10 to save the changes and exit the BIOS setup. The system reboots. Step 0: 7.6.
NANO-9452 EPIC Motherboard Step 4: Once the WDM_R140 icon is double clicked, the contents of the installation package are extracted. See Figure 7-24.
NANO-9452 EPIC Motherboard Step 5: The Welcome screen appears. Click NEXT. See Figure 7-25.
NANO-9452 EPIC Motherboard Step 6: The driver is automatically installed. Step 7: After the driver installation process is complete, a confirmation screen shown in Figure 7-26 appears. Figure 7-26: HD Audio Driver Installation Complete Step 8: The confirmation screen shown in Figure 7-26 allows you to restart the computer immediately after the installation is complete or to restart the computer later. For the settings to take effect the computer must be restarted.
NANO-9452 EPIC Motherboard 7.7 Realtek AC`97 Audio Driver (ALC665) Installation To install the Realtek AC `97 audio driver, please follow the steps below. 7.7.1 BIOS Setup Step 1: Enter the BIOS setup. To do this, reboot the system and press DEL during POST. Step 2: Go to the Southbridge Configuration menu. Set the Audio Controller option to [AC`97]. See Section Error! Reference source not found. for details. Step 3: Press F10 to save the changes and exit the BIOS setup. The system reboots. Step 0: 7.7.
NANO-9452 EPIC Motherboard Figure 7-27: CD 4-AUDIO\AC-KIT08R\Windows Folder Step 3: Double-click the Setup.exe file to begin the driver installation process. Step 4: Once you double click the Setup icon, the install shield wizard for the audio driver starts. See Figure 7-28. Figure 7-28: AC`97 Audio Driver Install Shield Wizard Starting Step 5: The Realtek Audio Setup prepares the install shield to guide you through the rest of the setup process. See Figure 7-25.
NANO-9452 EPIC Motherboard Figure 7-29: AC`97 Audio Driver Setup Preparation Page 191
NANO-9452 EPIC Motherboard Step 6: After the install shield is prepared, the welcome screen shown in Figure 7-30 appears. To continue the installation process, click the “NEXT” button. The install shield starts to configure the new software as shown in Figure 7-31.
NANO-9452 EPIC Motherboard Figure 7-31: AC`97 Audio Driver Software Configuration Page 193
NANO-9452 EPIC Motherboard Step 7: At this stage the “Digital Signal Not Found” screen appears (Figure 7-32). To continue the installation process, click the “YES” button.
NANO-9452 EPIC Motherboard Step 8: After clicking the “YES” button in Figure 7-32, the installation of the driver begins (Figure 7-33).
NANO-9452 EPIC Motherboard Step 9: After the driver installation process is complete, a confirmation screen shown in Figure 7-34 appears. Figure 7-34: AC`97 Audio Driver Installation Complete Step 10: The confirmation screen shown in Figure 7-34 allows you to restart the computer immediately after the installation is complete or to restart the computer later. For the settings to take effect the computer must be restarted. Once you have decided when to restart the computer, click the “FINISH” button.
NANO-9452 EPIC Motherboard 7.8 Intel Matrix Storage Manager Installation To install the Intel® Matrix Storage Manager driver, please follow the steps below: Step 1: Select SATA from the list in Figure 7-2. Step 2: A new window opens (Figure 7-35). Figure 7-35: SATA RAID Driver Installation Program Step 3: Double-click the INTEL folder. Step 4: Double-click the iata62_cd.exe program icon in Figure 7-36.
NANO-9452 EPIC Motherboard Figure 7-36: SATA RAID Setup Program Icon Step 5: Figure 7-37 shows the InstallShield Wizard preparing to guide the user through the rest of the process.
NANO-9452 EPIC Motherboard Step 6: Figure 7-38 shows the Matrix Storage Manager software configuring the installation process. Figure 7-38: Matrix Storage Manager Setup Screen Step 7: Figure 7-39 shows the Matrix Storage Manager welcome screen.
NANO-9452 EPIC Motherboard Step 8: Click NEXT and a warning appears (Figure 7-40). Read the warning carefully and decide whether or not to continue the installation process. Figure 7-40: Matrix Storage Manager Warning Screen Step 9: Click NEXT and a license agreement appears (Figure 7-41).
NANO-9452 EPIC Motherboard Step 10: Read the license agreement. To accept the terms and conditions stipulated in the license agreement shown, click YES and the Readme information file shown in Figure 7-42 appears. Figure 7-42: Matrix Storage Manager Readme File Step 11: Read the Readme file information and click NEXT.
NANO-9452 EPIC Motherboard Step 12: After the driver installation process is complete, a confirmation screen appears (Figure 7-43). Figure 7-43: Matrix Storage Manager Setup Complete Step 13: The confirmation screen offers the option of restarting the computer now or later. For the settings to take effect, the computer must be restarted. Click FINISH to restart the computer.
NANO-9452 EPIC Motherboard Appendix A A BIOS Options Page 203
NANO-9452 EPIC Motherboard System Overview .............................................................................................................. 100 System Time [xx:xx:xx] .................................................................................................... 101 System Date [xx/xx/xx] ..................................................................................................... 101 ATA/IDE Configurations [Compatible] ............................................................
NANO-9452 EPIC Motherboard Slope PWM 3 [2 PWM] ...................................................................................................... 120 Fan 3 PWM Control [070].................................................................................................. 121 Hardware Health Monitoring ............................................................................................ 121 ACPI Aware O/S [Yes] .......................................................................................
NANO-9452 EPIC Motherboard Clear NVRAM [No]............................................................................................................. 136 Plug & Play O/S [No]......................................................................................................... 136 PCI Latency Timer [64] ..................................................................................................... 137 Allocate IRQ to PCI VGA [Yes]...................................................................
NANO-9452 EPIC Motherboard TV Standard [Auto] ........................................................................................................... 159 Audio Controller [AC`97 Audio]....................................................................................... 160 OnBoard LAN1 [Auto]....................................................................................................... 160 On-board LAN2 [Auto].....................................................................................
NANO-9452 EPIC Motherboard THIS PAGE IS INTENTIONALLY LEFT BLANK Page 208
NANO-9452 EPIC Motherboard Appendix B B DIO Interface Page 209
NANO-9452 EPIC Motherboard B.1 DIO Interface Introduction The DIO connector on the NANO-9452 is interfaced to GIO ports on the iTE Super I/O chipset. The DIO has both 4-bit digital inputs and 4-bit digital outputs. The digital inputs and digital outputs are generally control signals that control the on/off circuit of external devices or TTL devices. Data can be read or written to the selected address to enable the DIO functions.
NANO-9452 EPIC Motherboard B.3 Assembly Language Samples B.3.1 Enable the DIO Input Function The BIOS interrupt call INT 15H controls the digital I/O. An assembly program to enable digital I/O input functions is listed below. MOV AX, 6F08H Sets the digital port as input INT 15H Initiates the INT 15H BIOS call B.3.2 Enable the DIO Output Function The BIOS interrupt call INT 15H controls the digital I/O. An assembly program to enable digital I/O output functions is listed below.
NANO-9452 EPIC Motherboard THIS PAGE IS INTENTIONALLY LEFT BLANK Page 212
NANO-9452 EPIC Motherboard Appendix C C Watchdog Timer Page 213
NANO-9452 EPIC Motherboard NOTE: The following discussion applies to DOS environment. IEI support is contacted or the IEI website visited for specific drivers for more sophisticated operating systems, e.g., Windows and Linux. The Watchdog Timer is provided to ensure that standalone systems can always recover from catastrophic conditions that cause the CPU to crash. This condition may have occurred by external EMI or a software bug.
NANO-9452 EPIC Motherboard NOTE: When exiting a program it is necessary to disable the Watchdog Timer, otherwise the system resets.
NANO-9452 EPIC Motherboard THIS PAGE IS INTENTIONALLY LEFT BLANK Page 216
NANO-9452 EPIC Motherboard Appendix D D Address Mapping Page 217
NANO-9452 EPIC Motherboard D.
NANO-9452 EPIC Motherboard D.3 IRQ Mapping Table IRQ0 System Timer IRQ8 RTC clock IRQ1 Keyboard IRQ9 ACPI IRQ2 Available IRQ10 LAN IRQ3 COM2 IRQ11 LAN/USB2.0/SATA IRQ4 COM1 IRQ12 PS/2 mouse IRQ5 SMBus Controller IRQ13 FPU IRQ6 FDC IRQ14 Primary IDE IRQ7 Available IRQ15 Secondary IDE Table D-3: IRQ Mapping Table D.
NANO-9452 EPIC Motherboard THIS PAGE IS INTENTIONALLY LEFT BLANK Page 220
NANO-9452 EPIC Motherboard Appendix E ® E Intel Matrix Storage Manager Page 221
NANO-9452 EPIC Motherboard E.1 Introduction The Intel® ICH7R chipset can provide data protection for serial ATA (SATA) disks via the Intel® Matrix Storage Manager using one of three fault-tolerant RAID levels: RAID 1, 5 or 10. When using two hard drives, matrix RAID allows RAID 0 and RAID 1 functions to be combined, where critical files can be stored on RAID 1, and RAID 0 can be used for non-critical items such as software.
NANO-9452 EPIC Motherboard CAUTION! Do not accidentally disconnect the SATA drive cables. Carefully route the cables within the chassis to avoid system down time. E.2 Features and Benefits Supports RAID levels 0, 1, 5 and 10 Supports connectivity to two or more disk drives Supported Operating Systems include: Windows XP, Windows Server 2003 and Windows Vista E.3 Accessing the Intel® Matrix Storage Manager To access the Intel® Matrix Storage Manager, please follow the steps below.
NANO-9452 EPIC Motherboard Step 3: Save and Exit BIOS. After the SATA support option is enabled, save and exit the BIOS. Step 4: Reboot the system. Reboot the system after saving and exiting the BIOS. Step 5: Press Ctrl+I. During the system boot process, press Ctrl+I when prompted to enter the RAID configuration software. Step 6: Configure the RAID settings. Use the Intel® Matrix Storage Manager to configure the RAID array. Brief descriptions of configuration options are given below. Step 7: Install the OS.
NANO-9452 EPIC Motherboard Step 1: Select “Create RAID Volume.” Use the arrow keys to highlight Create RAID Volume and press ENTER. See Figure E-1. Figure E-1: Matrix Storage Manager Main Menu Step 2: Name the RAID volume. Enter a name for the RAID volume, or press ENTER to accept the default volume name. Upper and lower case alphabetic, numeric, space, and underscore characters are all applicable for naming an array. See Figure E-2.
NANO-9452 EPIC Motherboard Step 3: Choose the RAID level. Select a RAID level from the list. RAID levels include RAID 0, 1, 5 and 10. See Figure E-3. NOTE: RAID 0 and RAID1 levels require a minimum of two hard drives. RAID 10 level requires a minimum of four hard drives. RAID5 level requires a minimum of three hard drives.
NANO-9452 EPIC Motherboard Step 4: Select the Stripe Size. Select a stripe size from the list. See Figure E-4. Figure E-4: Select the Stripe Size Step 5: Enter the Volume Capacity. Enter the volume capacity, or press ENTER to accept the default capacity. See Figure E-5.
NANO-9452 EPIC Motherboard Step 6: Create the RAID Volume. Press ENTER to create the RAID volume as specified. See Figure E-6. Figure E-6: Create the RAID Volume Step 7: Create RAID Volume Verification. After reading the warning, press Y to create the RAID volume as specified, or N to return to the Create RAID Volume menu. See Figure E-7.
NANO-9452 EPIC Motherboard E.4.2 Deleting a RAID Volume WARNING! All data stored on the member drives of a RAID volume are destroyed during the RAID deletion process. Make sure any data to be saved has been moved or backed up before deleting a RAID volume. Step 1: Select “Delete RAID Volume.” Use the arrow keys to highlight Delete RAID Volume and press ENTER. See Figure E-8.
NANO-9452 EPIC Motherboard Step 2: Select RAID Volume to be Deleted. Use the arrow keys to highlight the RAID volume to be deleted and press ENTER. See Figure E-9. Figure E-9: Select RAID Volume to be Deleted Step 3: Delete Volume Verification. After reading the warning, press Y to delete the specified RAID volume, or N to return to the Delete Volume menu. See Figure E-10.
NANO-9452 EPIC Motherboard Step 4: Non-RAID Disks. After deleting the RAID volume, the disks belonging to the volume will be shown as non-RAID disks. See Figure E-11. Step 0: Figure E-11: Non-RAID Disks E.4.3 Resetting a Disk to Non-RAID WARNING! All data stored on the disk drive of a RAID volume is destroyed when resetting it to non-RAID. Make sure any data to be saved has been moved or backed up before resetting a disk to non-RAID.
NANO-9452 EPIC Motherboard Step 1: Select “Reset Disk to Non-RAID.” Use the arrow keys to highlight Reset Disk to Non-RAID and press ENTER. See Figure E-12. Figure E-12: Reset Disk to Non-RAID Menu Step 2: Select Disks to Reset. Use the arrow keys to scroll through the disk drives and press SPACE to select which drives are to be reset as non-RAID. After all the disks to be reset have been chosen, press ENTER. See Figure E-13.
NANO-9452 EPIC Motherboard Step 3: Reset Disk Verification. After reading the warning, press Y to reset the selected disks as non-RAID, or N to return to the Reset RAID Data menu. See Figure E-14. Figure E-14: Reset Disk Verification Step 4: Disk Drive and RAID Volume Status. After the disk drives have been reset, the Matrix Storage Manager Main menu is shown indicating the status of the RAID volumes and disk drives. See Figure E-15.
NANO-9452 EPIC Motherboard E.4.4 Exiting the Matrix Storage Manager Step 1: Select “Exit.” Use the arrow keys to highlight Exit and press ENTER. See Figure E-16. Figure E-16: Exit Menu Step 2: Exit Verification. Press Y to exit the Matrix Storage Manager, or N to return to the Main menu. See Figure E-17.
NANO-9452 EPIC Motherboard F Index Page 235
NANO-9452 EPIC Motherboard BIOS chipset ....................................... 17, 18 + +12V ATX power supply connector............33 C location and pinouts ..............................33 cables.........................................................85 +5V ATX power supply connector..............34 CF card ............................................... 37, 75 location and pinouts ..............................34 installation..............................................75 location and pinouts.
NANO-9452 EPIC Motherboard connectors, pinouts and location dimensions...................................................8 +12V ATX power supply ........................33 board .......................................................8 +5V ATX power supply ..........................34 external peripheral interface connector ATX power supply enable......................35 panel....................................................8 audio......................................................
NANO-9452 EPIC Motherboard heat sink ....................................................72 K I keyboard ....................................... 45, 93, 95 keyboard connector .....................................4 IDE connector, 40-pin ..................................4 IDE connector, 44-pin ................................43 location and pinouts ..............................43 keyboard controller ....................................20 keyboard/mouse connector .......................
NANO-9452 EPIC Motherboard N R northbridge chipset .................................... 11 RAID ..........................................................54 real time clock ............................................16 P parallel port ................................ 20, 114, 115 parallel port connector .........................49, 50 location and pinouts ........................49, 50 parallel port connector .................................4 parallel port device.....................................
NANO-9452 EPIC Motherboard SIR interface ..............................................45 devices ..................................................58 SiS964 .....................................................159 port.........................................................58 socket 479 CPU USB 1.1 .................................................58 cooling kit ..............................................72 USB 2.0 .................................................58 cooling kit installation ....
