Manual

ManualsBrandsIEI Integration ManualsHardwareNANO-HM650

NANO-HM650 EPIC SBC

Page I

User Manual

NANO-HM650

MODEL:

EP IC SBC Supports Socket G2 In te l® 2nd generation Core™ i7/i5/i3

and Celeron® CPU, VGA/HDMI, Dual P CIe GbE, Eight USB 2.0,

Tw o S ATA 6Gb/s , Three COM, PCI-104, HD Audio and RoHS

Rev. 1.01 - 31 July, 2013

NANO-HM650 CPU Card

Summary of content (175 pages)

PAGE 1
NANO-HM650 EP IC S BC NANO-HM650 CPU Card MODEL: NANO-HM650 EP IC S BC S u p p o rts S o c ke t G2 In te l® 2n d g e n e ra tio n Co re ™ i7/i5/i3 a n d Ce le ro n ® CP U, VGA/HDMI, Du a l P CIe Gb E, Eig h t US B 2.0, Two S ATA 6Gb /s , Th re e COM, P CI-104, HD Au d io a n d Ro HS Us e r Ma n u a l Page I Re v. 1.
PAGE 2
NANO-HM650 EP IC S BC Re vis io n Date Version Changes 31 July, 2013 1.01 Update Section 3.2.2: Backlight Inverter Connector 3 February, 2012 1.
PAGE 3
NANO-HM650 EP IC S BC Co p yrig h t COP YRIGHT NOTICE The information in this document is subject to change without prior notice in order to improve reliability, design and function and does not represent a commitment on the part of the manufacturer. In no event will the manufacturer be liable for direct, indirect, special, incidental, or consequential damages arising out of the use or inability to use the product or documentation, even if advised of the possibility of such damages.
PAGE 4
NANO-HM650 EP IC S BC Ta b le o f Co n te n ts 1 INTRODUCTION.......................................................................................................... 1 1.1 INTRODUCTION........................................................................................................... 2 1.2 CONNECTORS ............................................................................................................. 3 1.3 DIMENSIONS .........................................................................
PAGE 5
NANO-HM650 EP IC S BC 3.2.13 PCI-104 Slot................................................................................................... 26 3.2.14 PCIe Mini Card Slot ...................................................................................... 27 3.2.15 Power Connector ........................................................................................... 27 3.2.16 SATA 6Gb/s Drive Connectors ....................................................................... 28 3.2.
PAGE 6
NANO-HM650 EP IC S BC 4.6 EXTERNAL PERIPHERAL INTERFACE CONNECTION ................................................... 58 4.6.1 HDMI Display Device Connection .................................................................. 59 4.6.2 LAN Connection ............................................................................................... 59 4.6.3 USB Connection ............................................................................................... 60 4.6.4 VGA Monitor Connection ..............
PAGE 7
NANO-HM650 EP IC S BC 6.2 SOFTWARE INSTALLATION ........................................................................................ 92 6.3 CHIPSET DRIVER INSTALLATION ............................................................................... 94 6.4 GRAPHICS DRIVER INSTALLATION ............................................................................ 97 6.5 LAN DRIVER INSTALLATION .................................................................................. 100 6.
PAGE 8
NANO-HM650 EP IC S BC C TERMINOLOGY ..................................................................................................... 149 D WATCHDOG TIMER .............................................................................................. 154 E HAZARDOUS MATERIALS DISCLOSURE ....................................................... 157 E.1 HAZARDOUS MATERIAL DISCLOSURE TABLE FOR IPB PRODUCTS CERTIFIED AS ROHS COMPLIANT UNDER 2002/95/EC WITHOUT MERCURY .....................................
PAGE 9
NANO-HM650 EP IC S BC Lis t o f Fig u re s Figure 1-1: NANO-HM650 ...............................................................................................................2 Figure 1-2: Connectors ..................................................................................................................3 Figure 1-3: NANO-HM650 Dimensions (mm) ...............................................................................4 Figure 1-4: Data Flow Block Diagram .....................................
PAGE 10
NANO-HM650 EP IC S BC Figure 4-2: Lock the CPU Socket Retention Screw ...................................................................44 Figure 4-3: IEI CF-989A-RS Cooling Kit ......................................................................................44 Figure 4-4: Cooling Kit Support Bracket ....................................................................................45 Figure 4-4: SO-DIMM Installation ....................................................................................
PAGE 11
NANO-HM650 EP IC S BC Figure 6-17: Audio Driver – Extracting Files ............................................................................103 Figure 6-18: Audio Driver Welcome Screen .............................................................................103 Figure 6-19: Audio Driver Installation.......................................................................................103 Figure 6-20: Audio Driver Installation Complete ..................................................................
PAGE 12
NANO-HM650 EP IC S BC Figure B-32: Recovery Tool Menu ............................................................................................132 Figure B-33: Recovery Tool Main Menu ...................................................................................133 Figure B-34: Restore Factory Default .......................................................................................134 Figure B-35: Recovery Complete Window ........................................................................
PAGE 13
NANO-HM650 EP IC S BC Lis t o f Ta b le s Table 1-1: Technical Specifications ..............................................................................................7 Table 3-1: Peripheral Interface Connectors ...............................................................................15 Table 3-2: Rear Panel Connectors ..............................................................................................15 Table 3-3: Audio Connector Pinouts ...............................................
PAGE 14
NANO-HM650 EP IC S BC Table 4-6: LVDS Voltage Select Jumper Settings .....................................................................52 Table 4-7: ME RTC Register Jumper Settings ...........................................................................53 Table 4-8: PCI-104 Power Select Jumper Settings ....................................................................53 Table 5-1: BIOS Navigation Keys ................................................................................................
PAGE 15
NANO-HM650 EP IC S BC Lis t o f BIOS Me n u s BIOS Menu 1: Main .......................................................................................................................66 BIOS Menu 2: Advanced ..............................................................................................................67 BIOS Menu 3: ACPI Configuration ..............................................................................................68 BIOS Menu 4: TPM Configuration ..............................
PAGE 16
NANO-HM650 EP IC S BC Chapter 1 1 In tro d u c tio n Page 1
PAGE 17
NANO-HM650 EP IC S BC 1.1 In tro d u c tio n Figure 1-1: NANO-HM650 The NANO-HM650 EPIC SBC motherboard is a Socket G2 32nm Intel® Core™ i7/i5/i3 and Celeron® mobile processor platform. Up to one 8.0 GB 1066 MHz or 1333 MHz DDR3 SDRAM SO-DIMM is supported by the NANO-HM650. The integrated Intel® HM65 System Chipset supports two GbE LAN ports through the dual Realtek RTL8111E Ethernet controllers (with ASF 2.0 support). The NANO-HM650 also supports two SATA 6Gb/s drives and provides 5 V SATA power.
PAGE 18
NANO-HM650 EP IC S BC 1.2 Co n n e c to rs The connectors on the NANO-HM650 are shown in the figure below.
PAGE 19
NANO-HM650 EP IC S BC 1.
PAGE 20
NANO-HM650 EP IC S BC 1.4 Da ta Flow Figure 1-4 shows the data flow between the system chipset, the CPU and other components installed on the motherboard.
PAGE 21
NANO-HM650 EP IC S BC 1.5 Te c h n ic a l Sp e c ific a tio n s NANO-HM650 technical specifications are listed in table below. S p e c ific a tio n NANO-HM650 Fo rm Fa c to r EPIC SBC S o c ke t Socket G2 CP U S u p p o rte d Intel® Core™ i7/i5/i3 and Celeron® mobile processor S ys te m Ch ip s e t Intel® HM65 Me m o ry One 204-pin 1066/1333 DDR3 SO-DIMM supported (system max. 8GB) Au d io Realtek ALC662 HD codec LAN Dual PCIe LAN controller by Realtek RTL8111E with ASF 2.
PAGE 22
NANO-HM650 EP IC S BC S p e c ific a tio n NANO-HM650 US B P o rts Four external USB ports Four internal USB ports via two 8-pin header One 4-pin CPU fan connector Fa n One 3-pin system fan connector Ke yb o a rd /Mo u s e One internal keyboard/mouse connector via 6-pin header S to ra g e S e ria l ATA Two SATA 6Gb/s connectors Two 5V SATA power connectors En viro n m e n ta l a n d P o we r S p e c ific a tio n s P o we r S u p p ly 12 V only ATX and AT power supported P o we r Co n n e c to r
PAGE 23
NANO-HM650 EP IC S BC Chapter 2 2 Un p a c kin g Page 8
PAGE 24
NANO-HM650 EP IC S BC 2.1 An ti-s ta tic P re c a u tio n s WARNING! Static electricity can destroy certain electronics. Make sure to follow the ESD precautions to prevent damage to the product, and injury to the user. Make sure to adhere to the following guidelines:  Wear an anti-static wristband: Wearing an anti-static wristband can prevent electrostatic discharge.  Self-grounding: Touch a grounded conductor every few minutes to discharge any excess static buildup.
PAGE 25
NANO-HM650 EP IC S BC 2.3 P a c kin g Lis t NOTE: If any of the components listed in the checklist below are missing, do not proceed with the installation. Contact the IEI reseller or vendor the NANO-HM650 was purchased from or contact an IEI sales representative directly by sending an email to sales@iei.com.tw.
PAGE 26
NANO-HM650 EP IC S BC 1 One Key Recovery CD 1 Quick Installation Guide 2.4 Op tio n a l Ite m s The following are optional components which may be separately purchased: Ite m a n d P a rt Nu m b e r Dual-port USB cable (P/N: 32001-008600-100-RS) RS-422/485 cable (P/N: 32205-003800-100-RS) Keyboard/Mouse cable (P/N: 32000-023800-RS) CPU Cooler for mobile socket-G up to 55 W processor, Copper, 60x60x27.
PAGE 27
NANO-HM650 EP IC S BC Chapter 3 3 Co n n e c to rs P a g e 12
PAGE 28
NANO-HM650 EP IC S BC 3.1 P e rip h e ra l In te rfa c e Co n n e c to rs This chapter details all the jumpers and connectors. 3.1.1 NANO-HM650 La yo u t The figures below show all the connectors and jumpers.
PAGE 29
NANO-HM650 EP IC S BC 3.1.2 P e rip h e ra l In te rfa c e Co n n e c to rs The table below lists all the connectors on the board.
PAGE 30
NANO-HM650 EP IC S BC TPM connector 20-pin connector TPM1 USB connector 8-pin header USB4_5,USB8_9 Table 3-1: Peripheral Interface Connectors 3.1.3 Exte rn a l In te rfa c e P a n e l Co n n e c to rs The table below lists the connectors on the external I/O panel. Connector Type Label Ethernet connectors RJ-45 LAN1，LAN2 HDMI connector HDMI port HDMI1 USB connectors USB port USB0_1，USB2_3 VGA connector 15-pin Female VGA1 Table 3-2: Rear Panel Connectors 3.
PAGE 31
NANO-HM650 EP IC S BC Figure 3-2: Audio Connector Location P IN NO. DES CRIP TION P IN NO. DES CRIP TION 1 LFRONT-R 2 LLINE-R 3 GND 4 GND 5 LFRONT-L 6 LLINE-L 7 GND 8 GND 9 LMIC1-CONN-R 10 LMIC1-CONN-L Table 3-3: Audio Connector Pinouts 3.2.2 Ba c klig h t In ve rte r Co n n e c to r CN La b e l: INV1 CN Typ e : 5-pin wafer CN Lo c a tio n : See Figure 3-3 CN P in o u ts : See Table 3-4 The backlight inverter connector provides power to an LCD panel.
PAGE 32
NANO-HM650 EP IC S BC Figure 3-3: Backlight Inverter Connector Location Pin Description 1 LCD_ADJ 2 GND 3 +12 V 4 GND 5 BL_EN Table 3-4: Backlight Inverter Connector Pinouts 3.2.3 Ba tte ry Co n n e c to r CN La b e l: BAT1 CN Typ e : 2-pin wafer CN Lo c a tio n : See Figure 3-4 CN P in o u ts : See Table 3-5 The battery connector is connected to the system battery. The battery provides power to the system clock to retain the time when power is turned off.
PAGE 33
NANO-HM650 EP IC S BC Figure 3-4: Battery Connector Location Pin Description 1 Battery+ 2 Ground Table 3-5: Battery Connector Pinouts 3.2.4 BIOS Upd a te Co n n e c to r CN La b e l: J S P I1 CN Typ e : 6-pin wafer CN Lo c a tio n : See Figure 3-5 CN P in o u ts : See Table 3-6 The BIOS update connector is for BIOS updating only and is located on the solder side (back).
PAGE 34
NANO-HM650 EP IC S BC Figure 3-5: BIOS Update Connector Location Pin Description Pin Description 1 +SPI_VCC 2 SPI_CS#0_CN 3 SPI_SO0_CN 4 SPI_CLK0_CN 5 SPI_SI0_CN 6 GND Table 3-6: BIOS Update Connector Pinouts 3.2.5 DDR3 S O-DIMM S o c ke t CN La b e l: DIMM1 CN Typ e : DDR3 SO-DIMM socket CN Lo c a tio n : See Figure 3-6 The DDR3 SO-DIMM socket is for DDR3 SO-DIMM memory module.
PAGE 35
NANO-HM650 EP IC S BC Figure 3-6: DDR3 SO-DIMM Socket Location 3.2.6 De b u g P o rt Co n n e c to r CN La b e l: DEBUGCN1 CN Typ e : 9-pin wafer CN Lo c a tio n : See Figure 3-7 CN P in o u ts : See Table 3-7 The debug port connector is for system debug.
PAGE 36
NANO-HM650 EP IC S BC Pin Description 4 LPC_AD3 5 LPC_AD2 6 LPC_AD1 7 LPC_AD0 8 LPC_FRAME# 9 +3.3V Table 3-7: Debug Port Connector Pinouts 3.2.7 Dig ita l I/O Co n n e c to r CN La b e l: DIO1 CN Typ e : 10-pin header CN Lo c a tio n : See Figure 3-8 CN P in o u ts : See Table 3-8 The digital I/O connector provides programmable input and output for external devices. The digital I/O provides 4-bit output and 4-bit input.
PAGE 37
NANO-HM650 EP IC S BC Pin Description Pin Description 3 DGPO3 4 DGPO2 5 DGPO1 6 DGPO0 7 DGPI3 8 DGPI2 9 DGPI1 10 DGPI0 Table 3-8: Digital I/O Connector Pinouts 3.2.8 Fa n Co n n e c to r (CP U) CN La b e l: CP U_FAN1 CN Typ e : 4-pin wafer CN Lo c a tio n : See Figure 3-9 CN P in o u ts : See Table 3-9 The fan connector attaches to a CPU cooling fan.
PAGE 38
NANO-HM650 EP IC S BC Pin Description 4 FANOUT1 Table 3-9: CPU Fan Connector Pinouts 3.2.9 Fa n Co n n e c to r (S ys te m ) CN La b e l: SYS_FAN1 CN Typ e : 3-pin wafer CN Lo c a tio n : See Figure 3-10 CN P in o u ts : See Table 3-10 The fan connector attaches to a cooling fan. Figure 3-10: System Fan Connector Location P IN NO. DES CRIP TION 1 NC 2 +12V 3 GND Table 3-10: System Fan Connector Pinouts 3.2.
PAGE 39
NANO-HM650 EP IC S BC CN Lo c a tio n : See Figure 3-11 CN P in o u ts : See Table 3-11 The front panel connector connects to external switches and indicators to monitor and controls the motherboard.
PAGE 40
NANO-HM650 EP IC S BC The keyboard/mouse connector connects to a PS/2 Y-cable that can be connected to a PS/2 keyboard and mouse. Figure 3-12: Keyboard/Mouse Connector Location Pin Description 1 VCC5_KBMS 2 MSDATA 3 MSCLK 4 KBDATA 5 KBCLK 6 GND Table 3-12: Keyboard/Mouse Connector Pinouts 3.2.
PAGE 41
NANO-HM650 EP IC S BC Figure 3-13: LVDS Connector Location Pin Description Pin Description 1 GND 2 GND 3 LVDSA_DATA0 4 LVDSA_DATA0# 5 LVDSA_DATA1 6 LVDSA_DATA1# 7 LVDSA_DATA2 8 LVDSA_DATA2# 9 LVDSA_CLK 10 LVDSA_CLK# 11 LVDSA_DATA3 12 LVDSA_DATA3# 13 GND 14 GND 15 LVDSB_DATA0 16 LVDSB_DATA0# 17 LVDSB_DATA1 18 LVDSB_DATA1# 19 LVDSB_DATA2 20 LVDSB_DATA2# 21 LVDSB_CLK 22 LVDSB_CLK# 23 LVDSB_DATA3 24 LVDSB_DATA3# 25 GND 26 GND 27 VCC_LCD 28 VCC_LCD 29
PAGE 42
NANO-HM650 EP IC S BC Figure 3-14: PCI-104 Connector Location 3.2.14 P CIe Min i Ca rd S lo t CN La b e l: MINI_P CIE1 CN Typ e : PCIe Mini card slot CN Lo c a tio n : See Figure 3-15 The PCIe Mini card slot is for installing PCIe Mini expansion cards. Figure 3-15: PCIe Mini Card Slot Location 3.2.
PAGE 43
NANO-HM650 EP IC S BC CN Type: 4-pin Molex CN Location: See Figure 3-16 CN Pinouts: See Table 3-14 The power connector supports the 12V power supply. Figure 3-16: Power Connector Location PIN NO. DESCRIPTION PIN NO. DESCRIPTION 1 GND 2 GND 3 +V12A_VIN 4 +V12A_VIN Table 3-14: Power Connector Pinouts 3.2.
PAGE 44
NANO-HM650 EP IC S BC Figure 3-17: SATA Drive Connector Locations 3.2.17 S ATA P o we r Co n n e c to rs CN La b e l: CN5, CN9 CN Typ e : 2-pin wafer CN Lo c a tio n : See Figure 3-18 CN P in o u ts : See Table 3-15 The SATA power connectors provide +5V power output to the SATA connectors. Figure 3-18: SATA Power Connector Locations PIN NO.
PAGE 45
NANO-HM650 EP IC S BC 3.2.18 S e ria l P o rt Co n n e c tors (RS -232) CN La b e l: COM1, COM2 CN Typ e : 10-pin header CN Lo c a tio n : See Figure 3-19 CN P in o u ts : See Table 3-16 These connectors provide RS-232 communications. Figure 3-19: COM Connector Pinout Locations P IN NO. DES CRIP TION P IN NO. DES CRIP TION 1 NDCD1/2 2 NRXD1/2 3 NTXD1/2 4 NDTR1/2 5 GND 6 NDSR1/2 7 NRTS1/2 8 NCTS1/2 9 NRI1/2 10 GND Table 3-16: COM Connector Pinouts 3.2.
PAGE 46
NANO-HM650 EP IC S BC This connector provides RS-422 or RS-485 communications. Figure 3-20: Serial Port Connector Location PIN NO. DESCRIPTION PIN NO. DESCRIPTION 1 RXD485# 2 RXD485+ 3 TXD485+ 4 TXD485# Table 3-17: Serial Port Connector Pinouts 3.2.20 S MBu s Co n n e c to r CN La b e l: SMBUS_1 CN Typ e : 4-pin wafer CN Lo c a tio n : See Figure 3-21 CN P in o u ts : See Table 3-18 The SMBus (System Management Bus) connector provides low-speed system management communications.
PAGE 47
NANO-HM650 EP IC S BC Figure 3-21: SMBus Connector Location P IN NO. DES CRIP TION P IN NO. DES CRIP TION 1 +5V_DUAL 2 SMBCLK_RESUME 3 SMBDATA_RESUME 4 GND Table 3-18: SMBus Connector Pinouts 3.2.21 TP M Co n n e c to r CN La b e l: TPM1 CN Typ e : 20-pin header CN Lo c a tio n : See Figure 3-22 CN P in o u ts : See Table 3-19 The TPM connector connects to a Trusted Platform Module (TPM) module.
PAGE 48
NANO-HM650 EP IC S BC Figure 3-22: TPM Connector Pinout Location PIN NO. DESCRIPTION PIN NO. DESCRIPTION 1 TPMPCLK 2 GND 3 LPC_FRAME# 4 NC 5 BUF_PCIRST# 6 +5V 7 LPC_AD3 8 LPC_AD2 9 +3.3V 10 LPC_AD1 11 LPC_AD0 12 GND 13 SMBCLK 14 SMBDATA 15 +3V_DUAL 16 SERIRQ 17 GND 18 +3.3V 19 LPCPD_N 20 LDRQ0# Table 3-19: TPM Connector Pinouts 3.2.
PAGE 49
NANO-HM650 EP IC S BC Figure 3-23: USB Connector Pinout Locations PIN NO. DESCRIPTION PIN NO. DESCRIPTION 1 +5V 2 GND 3 USB20_C_N4/8 4 USB20_C_P5/9 5 USB20_C_P4/8 6 USB20_C_N5/9 7 GND 8 +5V Table 3-20: USB Port Connector Pinouts 3.3 Exte rn a l P e rip h e ra l In te rfa c e Co n n e c to r P a n e l Figure 3-24 shows the NANO-HM650 external peripheral interface connector (EPIC) panel.
PAGE 50
NANO-HM650 EP IC S BC 3.3.1 Eth e rn e t Co n n e c to rs CN La b e l: LAN1, LAN2 CN Typ e : RJ-45 CN Lo c a tio n : See Figure 3-24 CN P in o u ts : See Table 3-21 The NANO-HM650 is equipped with two built-in RJ-45 Ethernet controllers. Each controller can connect to the LAN through one RJ-45 LAN connector. P IN DES CRIP TION P IN DES CRIP TION 1 MDI0+ 2 MDI0- 3 MDI1+ 4 MDI1- 5 GND 6 GND 7 MDI2+ 8 MDI2- 9 MDI3+ 10 MDI3- 11 LINK100 12 LINK1000 13 ACT 14 +V3.
PAGE 51
NANO-HM650 EP IC S BC Figure 3-25: RJ-45 Ethernet Connector 3.3.2 HDMI Co n n e c to r CN La b e l: HDMI1 CN Typ e : HDMI type A connector CN Lo c a tio n : See Figure 3-24 CN P in o u ts : See Table 3-23 The HDMI (High-Definition Multimedia Interface) connector connects to digital audio or video sources.
PAGE 52
NANO-HM650 EP IC S BC 3.3.3 US B Co n n e c to rs CN Label: USB0_1, USB2_3 CN Type: USB port CN Location: See Figure 3-24 CN Pinouts: See Table 3-24 The NANO-HM650 has four external USB 2.0 connectors. The USB connector can be connected to a USB device. PIN NO. DESCRIPTION PIN NO. DESCRIPTION 1 +5V 5 USB_PN0/2 2 USB_PP0/2 6 GND 3 +5V 7 USB_PN1/3 4 USB_PP1/3 8 GND Table 3-24: USB Port Connector Pinouts 3.3.
PAGE 53
NANO-HM650 EP IC S BC PIN DESCRIPTION PIN DESCRIPTION 1 RED 2 GREEN 3 BLUE 4 NC 5 GND 6 GND 7 GND 8 GND 9 VGAVCC 10 HOTPLUG 11 NC 12 DDCDAT 13 HSYNC 14 VSYNC 15 DDCCLK Table 3-25: VGA Connector Pinouts P a g e 38
PAGE 54
NANO-HM650 EP IC S BC Chapter 4 4 In s ta lla tio n P a g e 39
PAGE 55
NANO-HM650 EP IC S BC 4.1 An ti-s ta tic P re c a u tio n s WARNING: Failure to take ESD precautions during the installation of the NANO-HM650 may result in permanent damage to the NANO-HM650 and severe injury to the user. Electrostatic discharge (ESD) can cause serious damage to electronic components, including the NANO-HM650. Dry climates are especially susceptible to ESD.
PAGE 56
NANO-HM650 EP IC S BC WARNING: The installation instructions described in this manual should be carefully followed in order to prevent damage to the NANO-HM650, NANO-HM650 components and injury to the user. Before and during the installation please DO the following:  Read the user manual: o The user manual provides a complete description of the NANO-HM650 installation instructions and configuration options.
PAGE 57
NANO-HM650 EP IC S BC 4.3 Ba s ic In s ta lla tio n WARNING: A CPU should never be turned on without the specified cooling kit being installed. If the cooling kit (heat sink and fan) is not properly installed and the system turned on, permanent damage to the CPU, NANO-HM650 and other electronic components attached to the system may be incurred. Running a CPU without a cooling kit may also result in injury to the user. The CPU, CPU cooling kit and DIMM are the most critical components of the NANO-HM650.
PAGE 58
NANO-HM650 EP IC S BC Figure 4-1: Make sure the CPU socket retention screw is unlocked S te p 2: Inspect the CPU socket. Make sure there are no bent pins and make sure the socket contacts are free of foreign material. If any debris is found, remove it with compressed air. S te p 3: Correctly Orientate the CPU. Make sure the IHS (integrated heat sink) side is facing upwards. S te p 4: Correctly position the CPU. Match the Pin 1 mark with the cut edge on the CPU socket. See Figure 4-1.
PAGE 59
NANO-HM650 EP IC S BC Figure 4-2: Lock the CPU Socket Retention Screw 4.3.2 Co o lin g Kit In s ta lla tio n Figure 4-3: IEI CF-989A-RS Cooling Kit An IEI Socket 989A CPU cooling kit can be purchased separately. (See Chapter 3) The cooling kit comprises a CPU heat sink and a cooling fan. WARNING: Do not wipe off (accidentally or otherwise) the pre-sprayed layer of thermal paste on the bottom of the heat sink.
PAGE 60
NANO-HM650 EP IC S BC To install the cooling kit, please follow the steps below. S te p 1: Place the cooling kit onto the CPU. Make sure the CPU cooling fan cable can be properly routed when the cooling kit is installed. S te p 2: Properly align the cooling kit. Make sure its four spring screw fasteners can pass through the pre-drilled holes on the PCB. S te p 3: Secure the cooling kit.
PAGE 61
NANO-HM650 EP IC S BC 4.3.3 S O-DIMM In s ta lla tio n To install an SO-DIMM, please follow the steps below and refer to Figure 4-4. Figure 4-5: SO-DIMM Installation S te p 1: Locate the SO-DIMM socket. Place the board on an anti-static mat. S te p 2: Align the SO-DIMM with the socket. Align the notch on the memory with the notch on the memory socket. S te p 3: Insert the SO-DIMM. Push the memory in at a 20º angle. (See Figure 4-4) S te p 4: Seat the SO-DIMM.
PAGE 62
NANO-HM650 EP IC S BC Before the NANO-HM650 is installed in the system, the jumpers must be set in accordance with the desired configuration. The jumpers on the NANO-HM650 are listed in Table 4-1.
PAGE 63
NANO-HM650 EP IC S BC Figure 4-7: AT Auto Button Select Jumper Settings 4.4.2 AT/ATX P owe r S e le c t J u m p e r J u m p e r La b e l: J_ATXCTL1 J u m p e r Typ e : 3-pin header J u m p e r S e ttin g s : See Table 4-3 J u m p e r Lo c a tio n : See Figure 4-7 The AT/ATX Power Select jumper specifies the systems power mode as AT or ATX. AT/ATX Power Select jumper settings are shown in Table 4-3.
PAGE 64
NANO-HM650 EP IC S BC Figure 4-8: AT/ATX Power Select Jumper Location 4.4.3 Cle a r CMOS J u m p e r J u m p e r La b e l: ME_RTC2 J u m p e r Typ e : 3-pin header J u m p e r S e ttin g s : See Table 4-4 J u m p e r Lo c a tio n : See Figure 4-8 If the NANO-HM650 fails to boot due to improper BIOS settings, the clear CMOS jumper clears the CMOS data and resets the system BIOS information.
PAGE 65
NANO-HM650 EP IC S BC Clear CMOS Description Short 1 - 2 Normal Operation Short 2 - 3 Clear CMOS Setup Default Table 4-4: Clear CMOS Jumper Settings The location of the clear CMOS jumper is shown in Figure 4-8 below. Figure 4-9: Clear CMOS Jumper 4.4.4 LCD P a n e l Typ e J u m p e r J u m p e r La b e l: J _P ID1 J u m p e r Typ e : 8-pin header J u m p e r S e ttin g s : See Table 4-5 J u m p e r Lo c a tio n : See Figure 4-9 The LCD Panel Type jumper allows the LCD panel type to be set.
PAGE 66
NANO-HM650 EP IC S BC Pin Description 3-4 and 5-6 1600 x 1200 (48-bit) 1-2 and 3-4 and 5-6 1280 x 768 (18-bit) 7-8 1200 x 800 (18-bit) 1-2 and 7-8 1366 x 768 (24-bit) 3-4 and 7-8 1440 x 900 (36-bit) 1-2 and 3-4 and 7-8 1440 x 900 (48-bit) 5-6 and 7-8 1680 x 1050 (48-bit) 1-2 and 5-6 and 7-8 1920 x 1080 (48-bit) 3-4 and 5-6 and 7-8 1920 x 1200 (48-bit) Table 4-5: LVDS Screen Resolution Jumper Settings Figure 4-10: LVDS Screen Resolution Jumper Locations 4.4.
PAGE 67
NANO-HM650 EP IC S BC J u m p e r Lo c a tio n : See Figure 4-10 The LCD voltage select jumper sets the voltage of the power supplied to the LCD panel. Setting Description 1-2 +3.3 V (Default) 3-4 +5 V 5-6 +12 V Table 4-6: LVDS Voltage Select Jumper Settings Figure 4-11: LVDS Voltage Select Jumper Locations 4.4.
PAGE 68
NANO-HM650 EP IC S BC Setting Description Short 2-3 Clear ME RTC registers Table 4-7: ME RTC Register Jumper Settings Figure 4-12: ME RTC Register Jumper Location 4.4.7 P CI-104 P owe r S e le c t J u m p e r J u m p e r La b e l: J P1 J u m p e r Typ e : 3-pin header J u m p e r S e ttin g s : See Table 4-8 J u m p e r Lo c a tio n : See Figure 4-12 The PCI-104 power select jumper allows the user to select the PCI-104 power setting.
PAGE 69
NANO-HM650 EP IC S BC Figure 4-13: PCI-104 Power Select Jumper Location 4.5 In te rn a l P e rip h e ra l De vic e Co n n e c tio n s This section outlines the installation of peripheral devices to the onboard connectors 4.5.1 AT/ATX P owe r Co n n e c tio n Follow the instructions below to connect the NANO-HM650 to an AT or ATX power supply. WARNING: Disconnect the power supply power cord from its AC power source to prevent a sudden power surge to the NANO-HM650. S te p 1: Locate the power cable.
PAGE 70
NANO-HM650 EP IC S BC Figure 4-14: Power Cable to Motherboard Connection S te p 3: Connect Power Cable to Power Supply. Connect one of the 4-pin (1x4) Molex type power cable connectors to an AT/ATX power supply. See Figure 4-14.
PAGE 71
NANO-HM650 EP IC S BC Figure 4-15: Connect Power Cable to Power Supply 4.5.2 Au d io Kit In s ta lla tio n The Audio Kit that came with the NANO-HM650 connects to the audio connector on the NANO-HM650. The audio kit consists of three audio jacks. Mic-in connects to a microphone. Line-in provides a stereo line-level input to connect to the output of an audio device. Line-out, a stereo line-level output, connects to two amplified speakers.
PAGE 72
NANO-HM650 EP IC S BC Figure 4-16: Audio Kit Cable Connection S te p 3: Connect the audio devices. Connect speakers to the line-out audio jack. Connect the output of an audio device to the line-in audio jack. Connect a microphone to the mic-in audio jack.S te p 0: 4.5.3 S in g le RS -232 Ca ble Co n n e c tio n The single RS-232 cable consists of one serial port connector attached to a serial communications cable that is then attached to a D-sub 9 male connector.
PAGE 73
NANO-HM650 EP IC S BC Figure 4-17: Single RS-232 Cable Connection Secure the bracket. The single RS-232 connector has two retention screws S te p 3: that must be secured to a chassis or bracket. Connect the serial device. Once the single RS-232 connector is connected to S te p 4: a chassis or bracket, a serial communications device can be connected to the system. 4.
PAGE 74
NANO-HM650 EP IC S BC 4.6.1 HDMI Dis p la y De vic e Co n n e c tio n The NANO-HM650 has one female HDMI connector on the external peripheral interface panel. The HDMI connectors are connected to digital display devices. To connect a digital display device to the NANO-HM650, please follow the instructions below. S te p 1: Locate the HDMI connector. The location of the HDMI connector is shown in another chapter. S te p 2: Align the HDMI connector.
PAGE 75
NANO-HM650 EP IC S BC Figure 4-18: LAN Connection S te p 3: Insert the LAN cable RJ-45 connector. Once aligned, gently insert the LAN cable RJ-45 connector into the on-board RJ-45 connector. S te p 0: 4.6.3 US B Co n n e c tio n The external USB Series "A" receptacle connectors provide easier and quicker access to external USB devices. Follow the steps below to connect USB devices to the NANO-HM650. S te p 1: Locate the USB Series "A" receptacle connectors.
PAGE 76
NANO-HM650 EP IC S BC Figure 4-19: USB Connector 4.6.4 VGA Mo n ito r Co n n e c tio n The NANO-HM650 has a single female DB-15 connector on the external peripheral interface panel. The DB-15 connector is connected to a CRT or VGA monitor. To connect a monitor to the NANO-HM650, please follow the instructions below. S te p 1: Locate the female DB-15 connector. The location of the female DB-15 connector is shown in Chapter 3. S te p 2: Align the VGA connector.
PAGE 77
NANO-HM650 EP IC S BC Figure 4-20: VGA Connector S te p 4: Secure the connector. Secure the DB-15 VGA connector from the VGA monitor to the external interface by tightening the two retention screws on either side of the connector.
PAGE 78
NANO-HM650 EP IC S BC Chapter 5 5 BIOS P a g e 63
PAGE 79
NANO-HM650 EP IC S BC 5.1 In tro d u c tio n The BIOS is programmed onto the BIOS chip. The BIOS setup program allows changes to certain system settings. This chapter outlines the options that can be changed. 5.1.1 Sta rtin g S e tu p The AMI BIOS is activated when the computer is turned on. The setup program can be activated in one of two ways. 1. Press the DELETE key as soon as the system is turned on or 2. Press the DELETE key when the “Press Del to enter SETUP” message appears on the screen. 0.
PAGE 80
NANO-HM650 EP IC S BC Ke y Fu n c tio n F4 key Save all the CMOS changes Table 5-1: BIOS Navigation Keys 5.1.3 Ge ttin g He lp When F1 is pressed a small help window describing the appropriate keys to use and the possible selections for the highlighted item appears. To exit the Help Window press ESC or the F1 key again. 5.1.4 Un a b le to Re b o o t a fte r Co n fig u ra tio n Ch a n g e s If the computer cannot boot after changes to the system configuration is made, CMOS defaults.
PAGE 81
NANO-HM650 EP IC S BC 5.2 Ma in The Main BIOS menu (BIOS Menu 1) appears when the BIOS Setup program is entered. The Main menu gives an overview of the basic system information. Aptio Setup Utility – Copyright (C) 2010 American Megatrends, Inc. Main Advanced Chipset Boot Security Save & Exit BIOS Information BIOS Vendor Core Version Compliency Project Version Build Date American Megatrends 4.6.4.0 0.15 UEFI 2.1 SA66AR03.ROM 01/05/2012 18:24:22 Set the Date. Use Tab to switch between Data elements.
PAGE 82
NANO-HM650 EP IC S BC  S ys te m Tim e [xx:xx:xx] Use the System Time option to set the system time. Manually enter the hours, minutes and seconds. 5.3 Ad va n c e d Use the Advanced menu (BIOS Menu 2) to configure the CPU and peripheral devices through the following sub-menus: WARNING! Setting the wrong values in the sections below may cause the system to malfunction. Make sure that the settings made are compatible with the hardware. Aptio Setup Utility – Copyright (C) 2009 American Megatrends, Inc.
PAGE 83
NANO-HM650 EP IC S BC Aptio Setup Utility – Copyright (C) 2009 American Megatrends, Inc. Advanced ACPI Sleep State [S1 (CPU Stop Clock)] Set the ACPI state used for System suspend ---------------------: Select Screen ↑ ↓: Select Item Enter Select F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save ESC Exit Version 2.00.1201. Copyright (C) 2009 American Megatrends, Inc.
PAGE 84
NANO-HM650 EP IC S BC Aptio Setup Utility – Copyright (C) 2010 American Megatrends, Inc. Advanced TPM Configuration TPM SUPPORT [Disable] Current TPM Status Information NO TPM Hardware Enables or Disables TPM support. O.S. will not show TPM. Reset of platform is required. ---------------------: Select Screen ↑ ↓: Select Item Enter Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit Version 2.10.1208. Copyright (C) 2010 American Megatrends, Inc.
PAGE 85
NANO-HM650 EP IC S BC Aptio Setup Utility – Copyright (C) 2009 American Megatrends, Inc. Advanced CPU Configuration Intel(R) Core(TM) i7-2710QE CPU Processor Stepping Processor Revision Max Processor Speed Min Processor Speed Processor Speed Processor Cores Intel HT Technology EMT64 Hyper-threading Intel Virtualization Technology @ 2.
PAGE 86
NANO-HM650 EP IC S BC  Disables the use of hyper threading Disabled technology  Enabled DEFAULT Enables the use of hyper threading technology  In te l® Virtu a liza tio n Te c h n o lo g y [Dis a b le d ] Use the Intel® Virtualization Technology option to enable or disable virtualization on the system. When combined with third party software, Intel Virtualization technology allows several OSs to run on the same system at the same time.
PAGE 87
NANO-HM650 EP IC S BC  S ATA Co n tro lle r(s ) [En a b le d ] Use the SATA Controller(s) option to enable or disable the use of SATA Devices.   Enabled  Disabled DEFAULT Enables SATA devices. Disables SATA devices. S ATA Mo d e S e le c tio n [IDE] Use the SATA Mode option to configure SATA devices as normal IDE devices.  IDE  AHCI Configures SATA devices as AHCI device.  RAID Configures SATA devices as RAID device. DEFAULT Configures SATA devices as normal IDE device. 5.3.
PAGE 88
NANO-HM650 EP IC S BC  US B2.0 S u p p o rt [En a b le d ] Use the USB2.0 Support option to enable or disable USB2.0 support on the system.   Disabled  Enabled USB2.0 support disabled DEFAULT USB2.0 support enabled Le g a c y US B2.0 S u p p o rt [En a b le d ] Use the Legacy USB2.0 Support BIOS option to enable USB mouse and USB keyboard support.
PAGE 89
NANO-HM650 EP IC S BC 5.3.6 S u pe r IO Co n fig u ra tio n Use the Super IO Configuration menu (BIOS Menu 7) to set or change the configurations for the FDD controllers, parallel ports and serial ports. Aptio Setup Utility – Copyright (C) 2009 American Megatrends, Inc.
PAGE 90
NANO-HM650 EP IC S BC 5.3.6.1.1 S e ria l P o rt 1 Co n fig u ra tio n  S e ria l P o rt [En a b le d ] Use the Serial Port option to enable or disable the serial port.   Disabled  Enabled Disable the serial port DEFAULT Enable the serial port Ch a n g e S e ttin g s [Au to ] Use the Change Settings option to change the serial port IO port address and interrupt address.  Auto DEFAULT The serial port IO port address and interrupt address are automatically detected.
PAGE 91
NANO-HM650 EP IC S BC   Disabled  Enabled Disable the serial port DEFAULT Enable the serial port Ch a n g e S e ttin g s [Au to ] Use the Change Settings option to change the serial port IO port address and interrupt address.  Auto DEFAULT The serial port IO port address and interrupt address are automatically detected.
PAGE 92
NANO-HM650 EP IC S BC  Auto DEFAULT The serial port IO port address and interrupt address are automatically detected.
PAGE 93
NANO-HM650 EP IC S BC  P C He a lth Sta tu s The following system parameters and values are shown. The system parameters that are monitored are:  System Temperatures: o o o  CPU Temperature System Temperature1 System Temperature2 Voltages: o o o o o o o VCC3V V_core +1.05V VDDR VSB3V VBAT 5VSB 5.3.8 S e ria l P o rt Co n s o le Re d ire c tio n The Serial Port Console Redirection menu (BIOS Menu 10) allows the console redirection options to be configured.
PAGE 94
NANO-HM650 EP IC S BC  Co n s o le Re d ire c tio n Use Console Redirection option to enable or disable the console redirection function.  Disabled Disabled the console redirection function  Enabled Enabled the console redirection function 5.3.8.1 Co n s o le Re d ire c tio n S e ttin g s The Console Redirection Settings menu (BIOS Menu 11) allows the console redirection options to be configured. The option is active when Console Redirection option is enabled.
PAGE 95
NANO-HM650 EP IC S BC   VT-UTF8 The target terminal type is VT-UTF8  ANSI The target terminal type is ANSI Bits p e r s e c o n d [115200] Use the Bits per second option to specify the transmission speed of the serial port.  9600 The transmission speed is 9600  19200 The transmission speed is 19200  38400 The transmission speed is 38400  57600 The transmission speed is 57600  115200 DEFAULT The transmission speed is 115200 5.
PAGE 96
NANO-HM650 EP IC S BC Aptio Setup Utility – Copyright (C) 2009 American Megatrends, Inc. Main Advanced Chipset Boot Security Save & Exit > NorthBridge Configuration > SouthBridge Configuration NorthBridge Parameters --------------------: Select Screen ↑ ↓: Select Item Enter Select F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save ESC Exit Version 2.00.1201. Copyright (C) 2009 American Megatrends, Inc. BIOS Menu 13: Chipset 5.4.
PAGE 97
NANO-HM650 EP IC S BC 5.4.1.1 Gra p h ic s Co n fig u ra tio n Use the Graphics Configuration submenu (BIOS Menu 9) to configure graphics options. Aptio Setup Utility – Copyright (C) 2010 American Megatrends, Inc. Chipset Graphics Configuration DVMT Pre-Allocated DVMT Total Gfx Mem [64M] [MAX] Boot Display Device LCD Panel Type PID Current Jumper Setting [CRT+LFP] [By Hardware] Select DVMT 5.0 Pre-Allocated (Fixed) Graphics Memory size used by the Internal Graphics Device.
PAGE 98
NANO-HM650 EP IC S BC  192 M 192 MB of memory used by internal graphics device  224 M 224 MB of memory used by internal graphics device  256 M 256 MB of memory used by internal graphics device  288 M 288 MB of memory used by internal graphics device  320 M 320 MB of memory used by internal graphics device  352 M 352 MB of memory used by internal graphics device  384 M 384 MB of memory used by internal graphics device  416 M 416 MB of memory used by internal graphics device 
PAGE 99
NANO-HM650 EP IC S BC  256MB of memory used by internal graphics 256M device  MAX DEFAULT Maximum amount of memory used by internal graphics device  Bo o t Dis p la y De vic e [CRT+LFP ] Use the CRT+LFP option to configure the boot display device function.   CRT+LFP  CRT Enables CRT as the boot display device.  HDMI Enables HDMI as the boot display device.  LFP Enables LFP as the boot display device.  HDMI2 Enables HDMI2 as the boot display device.
PAGE 100
NANO-HM650 EP IC S BC  1440x900 48bit Sets the panel type to 1440x900 48bit  1600x900 48bit Sets the panel type to 1600x900 48bit  1680x1050 48bit Sets the panel type to 1680x1050 48bit  1920x1080 48bit Sets the panel type to 1920x1080 48bit  1920x1200 48bit Sets the panel type to 1920x1200 48bit 5.4.2 S o u th b rid g e Co n fig u ra tio n Use the Southbridge Configuration menu (BIOS Menu 14) to configure the Southbridge chipset.
PAGE 101
NANO-HM650 EP IC S BC  Disabled  Enabled The onboard High Definition Audio controller is disabled DEFAULT The onboard High Definition Audio controller is detected automatically and enabled  Aza lia In te rn a l HDMI Co d e c [Dis a b le d ] Use the Azalia internal HDMI Codec option to enable or disable the internal HDMI codec for High Definition Audio.
PAGE 102
NANO-HM650 EP IC S BC 5.5 Bo o t Use the Boot menu (BIOS Menu 16) to configure system boot options. Aptio Setup Utility – Copyright (C) 2009 American Megatrends, Inc. Main Advanced Chipset Boot Security Save & Exit Boot Configuration Bootup NumLock State [On] Quiet Boot [Enabled] Select the keyboard NumLock state --------------------: Select Screen ↑ ↓: Select Item Enter Select F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save ESC Exit Version 2.00.1201.
PAGE 103
NANO-HM650 EP IC S BC  Disabled  Enabled Normal POST messages displayed DEFAULT OEM Logo displayed instead of POST messages 5.6 S e c u rity Use the Security menu (BIOS Menu 17) to set system and user passwords. Aptio Setup Utility – Copyright (C) 2009 American Megatrends, Inc.
PAGE 104
NANO-HM650 EP IC S BC 5.7 Exit Use the Exit menu (BIOS Menu 18) to load default BIOS values, optimal failsafe values and to save configuration changes. Aptio Setup Utility – Copyright (C) 2009 American Megatrends, Inc. Main Advanced Chipset Boot Security Save & Exit Save Changes and Reset Discard Changes and Reset Reset the system after saving the changes.
PAGE 105
NANO-HM650 EP IC S BC  Re s to re Us e r De fa u lts Use the Restore User Defaults option to restore the user defaults to all the setup options.
PAGE 106
NANO-HM650 EP IC S BC Chapter 6 6 S o ftwa re Drive rs P a g e 91
PAGE 107
NANO-HM650 EP IC S BC 6.1 Ava ila b le S o ftwa re Drive rs NOTE: The content of the CD may vary throughout the life cycle of the product and is subject to change without prior notice. Visit the IEI website or contact technical support for the latest updates. The following drivers can be installed on the system:  Chipset  Graphic  LAN  Audio Installation instructions are given below. 6.2 S o ftwa re In s ta lla tio n All the drivers for the NANO-HM650 are on the CD that came with the system.
PAGE 108
NANO-HM650 EP IC S BC Figure 6-1: Introduction Screen S te p 3: Click NANO-HM650. S te p 4: A new screen with a list of available drivers appears (Figure 6-2).
PAGE 109
NANO-HM650 EP IC S BC S te p 5: Install all of the necessary drivers in this menu. 6.3 Ch ips e t Drive r In s ta lla tio n To install the chipset driver, please do the following. S te p 1: Access the driver list. (See Section 6.2) S te p 2: Click “Chipset”. S te p 3: Locate the setup file and double click on it. S te p 4: The setup files are extracted as shown in Figure 6-3.
PAGE 110
NANO-HM650 EP IC S BC Figure 6-4: Chipset Driver Welcome Screen S te p 7: The license agreement in Figure 6-5 appears. S te p 8: Read the License Agreement. S te p 9: Click Yes to continue. Figure 6-5: Chipset Driver License Agreement S te p 10: The Read Me file in Figure 6-6 appears.
PAGE 111
NANO-HM650 EP IC S BC S te p 11: Click Next to continue. Figure 6-6: Chipset Driver Read Me File S te p 12: Setup Operations are performed as shown in Figure 6-7. S te p 13: Once the Setup Operations are complete, click Next to continue.
PAGE 112
NANO-HM650 EP IC S BC S te p 14: The Finish screen in Figure 6-8 appears. S te p 15: Select “Yes, I want to restart this computer now” and click Finish.S te p 0: Figure 6-8: Chipset Driver Installation Finish Screen 6.4 Gra p h ic s Drive r In s ta lla tio n To install the Graphics driver, please do the following. S te p 1: Access the driver list. (See Section 6.2) S te p 2: Click “VGA” and select the folder which corresponds to the operating system. S te p 3: Double click the setup file.
PAGE 113
NANO-HM650 EP IC S BC Figure 6-9: Graphics Driver Welcome Screen S te p 6: The License Agreement in Figure 6-10 appears. S te p 7: Click Yes to accept the agreement and continue. Figure 6-10: Graphics Driver License Agreement S te p 8: Setup Operations are performed as shown in Figure 6-11.
PAGE 114
NANO-HM650 EP IC S BC S te p 9: Once the Setup Operations are complete, click Next to continue. Figure 6-11: Graphics Driver Setup Operations S te p 10: The Finish screen in Figure 6-12 appears. S te p 11: Select “Yes, I want to restart this computer now” and click Finish.
PAGE 115
NANO-HM650 EP IC S BC 6.5 LAN Drive r In s ta lla tio n To install the LAN driver, please do the following. S te p 1: Access the driver list. (See Section 6.2) S te p 2: Click “LAN” and select the folder which corresponds to the operating system. S te p 3: Double click the setup file. S te p 4: The Welcome screen in Figure 6-13 appears. Figure 6-13: LAN Driver Welcome Screen S te p 5: Click Next to continue. S te p 6: The Ready to Install the Program Screen in Figure 6-14 appears.
PAGE 116
NANO-HM650 EP IC S BC Figure 6-14: LAN Driver Ready to Install Screen S te p 8: The program begins to install. S te p 9: The Setup Status screen in Figure 6-15 appears. Figure 6-15: LAN Driver Setup Status Screen S te p 10: When the driver installation is complete, the screen in Figure 6-16 appears. S te p 11: Click Finish to exit.
PAGE 117
NANO-HM650 EP IC S BC Figure 6-16: LAN Driver Installation Complete 6.6 Au d io Drive r In s ta lla tio n To install the audio driver, please do the following. S te p 1: Access the driver list. (See Section 6.2) S te p 2: Click “Audio” and select the folder which corresponds to the operating system. S te p 3: Double click the setup file. S te p 4: The InstallShield Wizard starts to extracting files (Figure 6-17).
PAGE 118
NANO-HM650 EP IC S BC Figure 6-17: Audio Driver – Extracting Files S te p 5: The Audio Driver Welcome message in Figure 6-18 appears. S te p 6: Click Yes to install the audio driver. Figure 6-18: Audio Driver Welcome Screen S te p 7: The audio driver installation begins. See Figure 6-19. Figure 6-19: Audio Driver Installation S te p 8: P a g e 103 When the installation is complete, the screen in Figure 6-20 appears.
PAGE 119
NANO-HM650 EP IC S BC S te p 9: Select “Yes, I want to restart my computer now” and click OK.
PAGE 120
NANO-HM650 EP IC S BC Ap p e n d ix A A BIOS Me n u Op tio n s P a g e 105
PAGE 121
NANO-HM650 EP IC S BC  BIOS Information .................................................................................................................66  System Date [xx/xx/xx] ........................................................................................................66  System Time [xx:xx:xx] .......................................................................................................67  ACPI Sleep State [S1 (CPU Stop Clock)] ............................................
PAGE 122
NANO-HM650 EP IC S BC  Discard Changes and Reset ...............................................................................................89  Restore Defaults ..................................................................................................................89  Save as User Defaults .........................................................................................................89  Restore User Defaults .................................................................
PAGE 123
NANO-HM650 EP IC S BC Ap p e n d ix B B On e Ke y Re c o ve ry P a g e 108
PAGE 124
NANO-HM650 EP IC S BC B.1 On e Ke y Re c o ve ry In tro d u c tio n The IEI one key recovery is an easy-to-use front end for the Norton Ghost system backup and recovery tool. This tool provides quick and easy shortcuts for creating a backup and reverting to that backup or reverting to the factory default settings.
PAGE 125
NANO-HM650 EP IC S BC After completing the five initial setup procedures as described above, users can access the recovery tool by pressing while booting up the system. The detailed information of each function is described in Section B.5. NOTE: The initial setup procedures for Linux system are described in Section B.3. B.1.1 S ys te m Re q u ire m e n t NOTE: The recovery CD can only be used with IEI products.
PAGE 126
NANO-HM650 EP IC S BC partitions. Please take the following table as a reference when calculating the size of the partition. OS OS Image after Ghost Compression Ratio Windows® 7 7 GB 5 GB 70% Windows® XPE 776 MB 560 MB 70% Windows® CE 6.0 36 MB 28 MB 77% NOTE: Specialized tools are required to change the partition size if the operating system is already installed. B.1.
PAGE 127
NANO-HM650 EP IC S BC o o o o o o o Ubuntu 8.10 (Intrepid) Ubuntu 7.10 (Gutsy) Ubuntu 6.10 (Edgy) Debian 5.0 (Lenny) Debian 4.0 (Etch) SuSe 11.2 SuSe 10.3 NOTE: Installing unsupported OS versions may cause the recovery tool to fail. B.2 S e tu p P ro c e d u re fo r Win d ows Prior to using the recovery tool to backup or restore, a few setup procedures are required. S te p 1: Hardware and BIOS setup (see Section B.2.1) S te p 2: Create partitions (see Section B.2.
PAGE 128
NANO-HM650 EP IC S BC B.2.1 Ha rdwa re a n d BIOS S e tu p S te p 1: Make sure the system is powered off and unplugged. S te p 2: Install a hard drive or SSD in the system. An unformatted and unpartitioned disk is recommended. S te p 3: Connect an optical disk drive to the system and insert the recovery CD. S te p 4: Turn on the system. S te p 5: Press the key as soon as the system is turned on to enter the BIOS. S te p 6: Select the connected optical disk drive as the 1 boot device.
PAGE 129
NANO-HM650 EP IC S BC Figure B-2: Launching the Recovery Tool S te p 3: The recovery tool setup menu is shown as below. Figure B-3: Recovery Tool Setup Menu S te p 4: Press <6> then .
PAGE 130
NANO-HM650 EP IC S BC Figure B-4: Command Prompt S te p 5: The command prompt window appears. Type the following commands (marked in red) to create two partitions. One is for the OS installation; the other is for saving recovery files and images which will be an invisible partition.
PAGE 131
NANO-HM650 EP IC S BC Figure B-5: Partition Creation Commands P a g e 116
PAGE 132
NANO-HM650 EP IC S BC NOTE: Use the following commands to check if the partitions were created successfully. S te p 6: Press any key to exit the recovery tool and automatically reboot the system. Please continue to the following procedure: Build the Recovery Partition.Step0: B.2.3 In s ta ll Op e ra tin g S ys te m , Drive rs a n d Ap p lic a tio n s Install the operating system onto the unlabelled partition.
PAGE 133
NANO-HM650 EP IC S BC B.2.4 Bu ild in g th e Re c o ve ry P a rtitio n S te p 1: Put the recover CD in the optical drive. S te p 2: Start the system. S te p 3: Boot the system from the recovery CD. When prompted, press any key to boot from the recovery CD. It will take a while to launch the recovery tool. Please be patient! Figure B-6: Launching the Recovery Tool S te p 4: When the recovery tool setup menu appears, press <2> then .
PAGE 134
NANO-HM650 EP IC S BC S te p 5: The Symantec Ghost window appears and starts configuring the system to build a recovery partition. In this process the partition created for recovery files in Section B.2.2 is hidden and the recovery tool is saved in this partition. Figure B-8: Building the Recovery Partition S te p 6: After completing the system configuration, press any key in the following window to reboot the system. Figure B-9: Press Any Key to Continue S te p 7: P a g e 119 Eject the recovery CD.
PAGE 135
NANO-HM650 EP IC S BC B.2.5 Cre a te Fa c to ry De fa u lt Im a g e NOTE: Before creating the factory default image, please configure the system to a factory default environment, including driver and application installations. To create a factory default image, please follow the steps below. S te p 1: Turn on the system. When the following screen displays (Figure B-10), press the key to access the recovery tool.
PAGE 136
NANO-HM650 EP IC S BC Figure B-12: About Symantec Ghost Window S te p 4: Use mouse to navigate to the option shown below (Figure B-13). Figure B-13: Symantec Ghost Path S te p 5: P a g e 121 Select the local source drive (Drive 1) as shown in Figure B-14. Then click OK.
PAGE 137
NANO-HM650 EP IC S BC Figure B-14: Select a Local Source Drive S te p 6: Select a source partition (Part 1) from basic drive as shown in Figure B-15. Then click OK. Figure B-15: Select a Source Partition from Basic Drive S te p 7: Select 1.2: [Recovery] NTFS drive and enter a file name called iei (Figure B-16). Click Save. The factory default image will then be saved in the selected recovery drive and named IEI.GHO. WARNING: The file name of the factory default image must be iei.GHO.
PAGE 138
NANO-HM650 EP IC S BC Figure B-16: File Name to Copy Image to S te p 8: When the Compress Image screen in Figure B-17 prompts, click High to make the image file smaller.
PAGE 139
NANO-HM650 EP IC S BC S te p 9: The Proceed with partition image creation window appears, click Yes to continue. Figure B-18: Image Creation Confirmation S te p 10: The Symantec Ghost starts to create the factory default image (Figure B-19). Figure B-19: Image Creation Complete S te p 11: When the image creation completes, a screen prompts as shown in Figure B-20. Click Continue and close the Ghost window to exit the program.
PAGE 140
NANO-HM650 EP IC S BC S te p 12: The recovery tool main menu window is shown as below. Press any key to reboot the system. Step0: Figure B-21: Press Any Key to Continue B.3 Au to Re c o ve ry S e tu p P ro c e d u re The auto recovery function allows a system to automatically restore from the factory default image after encountering a Blue Screen of Death (BSoD) or a hang for around 10 minutes. To use the auto recovery function, follow the steps described in the following sections.
PAGE 141
NANO-HM650 EP IC S BC Figure B-22: Auto Recovery Utility S te p 3: Reboot the system from the recovery CD. When prompted, press any key to boot from the recovery CD. It will take a while to launch the recovery tool. Please be patient! Figure B-23: Launching the Recovery Tool S te p 4: When the recovery tool setup menu appears, press <4> then .
PAGE 142
NANO-HM650 EP IC S BC S te p 5: The Symantec Ghost window appears and starts configuring the system to build an auto recovery partition. In this process the partition created for recovery files in Section B.2.2 is hidden and the auto recovery tool is saved in this partition. Figure B-25: Building the Auto Recovery Partition S te p 6: After completing the system configuration, the following message prompts to confirm whether to create a factory default image.
PAGE 143
NANO-HM650 EP IC S BC S te p 7: The Symantec Ghost starts to create the factory default image (Figure B-27). Figure B-27: Image Creation Complete S te p 8: After completing the system configuration, press any key in the following window to restart the system. Figure B-28: Press any key to continue S te p 9: Eject the One Key Recovery CD and restart the system. S te p 10: Press the key as soon as the system is turned on to enter the BIOS.
PAGE 144
NANO-HM650 EP IC S BC Main Advanced PCIPNP BIOS SETUP UTILITY Boot Security Chipset Exit iEi Feature  Auto Recovery Function [Enabled] Recover from PXE [Disabled]  ↑ ↓ Enter F1 F10 ESC Select Screen Select Item Go to SubScreen General Help Save and Exit Exit v02.61 ©Copyright 1985-2006, American Megatrends, Inc. BIOS Menu 20: IEI Feature S te p 12: Save changes and restart the system.
PAGE 145
NANO-HM650 EP IC S BC Install Linux operating system. Make sure to install GRUB (v0.97 or earlier) S te p 2: MBR type and Ext3 partition type. Leave enough space on the hard drive to create the recover partition later. NOTE: If the Linux OS is not installed with GRUB (v0.97 or earlier) and Ext3, the Symantec Ghost may not function properly.
PAGE 146
NANO-HM650 EP IC S BC DISKPART>create part pri size= ___ DISKPART>assign letter=N DISKPART>exit system32>format N: /fs:ntfs /q /v:Recovery /y system32>exit S te p 4: Build the recovery partition. Press any key to boot from the recovery CD. It will take a while to launch the recovery tool. Please be patient. When the recovery tool setup menu appears, type <3> and press (Figure B-30). The Symantec Ghost window appears and starts configuring the system to build a recovery partition.
PAGE 147
NANO-HM650 EP IC S BC Figure B-31: Access menu.lst in Linux (Text Mode) S te p 6: Modify the menu.lst as shown below. S te p 7: The recovery tool menu appears. (Figure B-32) Figure B-32: Recovery Tool Menu S te p 8: Create a factory default image. Follow Step 2 ~ Step 12 described in Section B.2.5 to create a factory default image.
PAGE 148
NANO-HM650 EP IC S BC B.5 Re c o ve ry To o l Fu n c tio n s After completing the initial setup procedures as described above, users can access the recovery tool by pressing while booting up the system. However, if the setup procedure in Section B.3 has been completed and the auto recovery function is enabled, the system will automatically restore from the factory default image without pressing the F3 key. The recovery tool main menu is shown below.
PAGE 149
NANO-HM650 EP IC S BC WARNING: All data in the system will be deleted during the system recovery. Please backup the system files before restoring the system (either Factory Restore or Restore Backup). B.5.1 Fa c to ry Re s to re To restore the factory default image, please follow the steps below. S te p 1: Type <1> and press in the main menu. S te p 2: The Symantec Ghost window appears and starts to restore the factory default. A factory default image called iei.
PAGE 150
NANO-HM650 EP IC S BC Figure B-35: Recovery Complete Window B.5.2 Ba c ku p S ys te m To backup the system, please follow the steps below. S te p 1: Type <2> and press in the main menu. S te p 2: The Symantec Ghost window appears and starts to backup the system. A backup image called iei_user.GHO is created in the hidden Recovery partition. Figure B-36: Backup System S te p 3: The screen shown in Figure B-37 appears when system backup is complete. Press any key to reboot the system.
PAGE 151
NANO-HM650 EP IC S BC Figure B-37: System Backup Complete Window B.5.3 Re s to re Yo u r La s t Ba c ku p To restore the last system backup, please follow the steps below. S te p 1: Type <3> and press in the main menu. S te p 2: The Symantec Ghost window appears and starts to restore the last backup image (iei_user.GHO). Figure B-38: Restore Backup S te p 3: The screen shown in Figure B-39 appears when backup recovery is complete. Press any key to reboot the system.
PAGE 152
NANO-HM650 EP IC S BC Figure B-39: Restore System Backup Complete Window B.5.4 Ma n u a l To restore the last system backup, please follow the steps below. S te p 1: Type <4> and press in the main menu. S te p 2: The Symantec Ghost window appears. Use the Ghost program to backup or recover the system manually. Figure B-40: Symantec Ghost Window S te p 3: When backup or recovery is completed, press any key to reboot the system.
PAGE 153
NANO-HM650 EP IC S BC B.6 Re s to re S ys te m s fro m a Lin u x S e rve r thro u g h LAN The One Key Recovery allows a client system to automatically restore to a factory default image saved in a Linux system (the server) through LAN connectivity after encountering a Blue Screen of Death (BSoD) or a hang for around 10 minutes. To be able to use this function, the client system and the Linux system MUST reside in the same domain.
PAGE 154
NANO-HM650 EP IC S BC The detailed descriptions are described in the following sections. In this document, two types of Linux OS are used as examples to explain the configuration process – CentOS 5.5 (Kernel 2.6.18) and Debian 5.0.7 (Kernel 2.6.26). B.6.1 Co n fig u re DHCP S e rve r S e ttin g s S te p 1: Install the DHCP #yum install dhcp (CentOS, commands marked in red) #apt-get install dhcp3-server (Debian, commands marked in blue) S te p 2: Confirm the operating system default settings: dhcpd.conf.
PAGE 155
NANO-HM650 EP IC S BC Edit “/etc/dhcpd.conf” for your environment. For example, add next-server PXE server IP address; filename “pxelinux.0”; B.6.2 Co n fig u re TFTP S e ttin g s S te p 1: Install the tftp, httpd and syslinux. #yum install tftp-server httpd syslinux (CentOS) #apt-get install tftpd-hpa xinetd syslinux (Debian) S te p 2: Enable the TFTP server by editing the “/etc/xinetd.d/tftp” file and make it use the remap file.
PAGE 156
NANO-HM650 EP IC S BC Debian Replace the TFTP settings from “inetd” to “xinetd” and annotate the “inetd” by adding “#”. #vi /etc/inetd.conf Modify: #tftp dgram udp wait root /usr/sbin....... (as shown below) #vi /etc/xinetd.d/tftp B.6.3 Co n fig u re On e Ke y Re c o ve ry S e rve r S e ttin g s S te p 1: Copy the Utility/RECOVERYR10.TAR.BZ2 package from the One Key Recovery CD to the system (server side).
PAGE 157
NANO-HM650 EP IC S BC S te p 2: Extract the recovery package to /. #cp RecoveryR10.tar.bz2 / #cd / #tar –xvjf RecoveryR10.tar.bz2 S te p 3: Copy “pxelinux.0” from “syslinux” and install to “/tftboot”. #cp /usr/lib/syslinux/pxelinux.0 /tftpboot/ B.6.4 Sta rt th e DHCP, TFTP a n d HTTP Start the DHCP, TFTP and HTTP. For example: CentOS #service xinetd restart #service httpd restart #service dhcpd restart Debian #/etc/init.d/xinetd reload #/etc/init.d/xinetd restart #/etc/init.d/dhcp3-server restart B.6.
PAGE 158
NANO-HM650 EP IC S BC WARNING: The file name of the factory default image must be iei.gho. S te p 3: Confirm the operating system default settings: smb.conf. #vi /etc/samba/smb.conf Modify: [image] comment = One Key Recovery path = /share/image browseable = yes writable = yes public = yes create mask = 0644 directory mask = 0755 S te p 4: Edit “/etc/samba/smb.conf” for your environment.
PAGE 159
NANO-HM650 EP IC S BC B.6.6 S e tu p a Clie n t S ys te m fo r Au to Re c o ve ry S te p 1: Configure the following BIOS options of the client system. Advanced → iEi Feature → Auto Recovery Function → Enabled Advanced → iEi Feature → Recover from PXE → Enabled Boot → Launch PXE OpROM → Enabled S te p 2: Continue to configure the Boot Option Priorities BIOS option of the client system: Boot Option #1  remain the default setting to boot from the original OS.
PAGE 160
NANO-HM650 EP IC S BC NOTE: A firewall or a SELinux is not in use in the whole setup process. If there is a firewall or a SELinux protecting the system, modify the configuration information to accommodate them.
PAGE 161
NANO-HM650 EP IC S BC B.7 Oth e r In fo rm a tio n B.7.1 Us in g AHCI Mo d e o r ALi M5283 / VIA VT6421A Co n tro lle r When the system uses AHCI mode or some specific SATA controllers such as ALi M5283 or VIA VT6421A, the SATA RAID/AHCI driver must be installed before using one key recovery. Please follow the steps below to install the SATA RAID/AHCI driver. S te p 1: Copy the SATA RAID/AHCI driver to a floppy disk and insert the floppy disk into a USB floppy disk drive.
PAGE 162
NANO-HM650 EP IC S BC S te p 5: When the following window appears, press ~~to select “Specify Additional Device”. S te p 6: In the following window, select a SATA controller mode used in the system. Then press . The user can now start using the SATA HDD.~~
~~PAGE 163~~
NANO-HM650 EP IC S BC After pressing , the system will get into the recovery tool setup menu. S te p 7: Continue to follow the setup procedure from Step 4 in Section B.2.2 Create Partitions to finish the whole setup process.Step0: B.7.2 S ys te m Me m o ry Re q u ire m e n t To be able to access the recovery tool by pressing while booting up the system, please make sure to have enough system memory. The minimum memory requirement is listed below.
~~PAGE 164~~
~~NANO-HM650 EP IC S BC Ap p e n d ix C C Te rm in o lo g y P a g e 149~~
~~PAGE 165~~
NANO-HM650 EP IC S BC AC ’97 Audio Codec 97 (AC’97) refers to a codec standard developed by Intel® in 1997. ACPI Advanced Configuration and Power Interface (ACPI) is an OS-directed configuration, power management, and thermal management interface. AHCI Advanced Host Controller Interface (AHCI) is a SATA Host controller register-level interface. ATA The Advanced Technology Attachment (ATA) interface connects storage devices including hard disks and CD-ROM drives to a computer.
~~PAGE 166~~
NANO-HM650 EP IC S BC computer is usually a male DE-9 connector. DAC The Digital-to-Analog Converter (DAC) converts digital signals to analog signals. DDR Double Data Rate refers to a data bus transferring data on both the rising and falling edges of the clock signal. DMA Direct Memory Access (DMA) enables some peripheral devices to bypass the system processor and communicate directly with the system memory.
~~PAGE 167~~
NANO-HM650 EP IC S BC PCIe PCI Express (PCIe) is a communications bus that uses dual data lines for full-duplex (two-way) serial (point-to-point) communications between the SBC components and/or expansion cards and the SBC chipsets. Each line has a 2.5 Gbps data transmission rate and a 250 MBps sustained data transfer rate. POST The Power-on Self Test (POST) is the pre-boot actions the system performs when the system is turned-on.
~~PAGE 168~~
~~NANO-HM650 EP IC S BC USB 2.0 supports 480Mbps data transfer rates. VGA The Video Graphics Array (VGA) is a graphics display system developed by IBM.~~
~~PAGE 169~~
~~NANO-HM650 EP IC S BC Ap p e n d ix D D Wa tc h d o g Tim e r P a g e 154~~
~~PAGE 170~~
NANO-HM650 EP IC S BC NOTE: The following discussion applies to DOS environment. IEI support is contacted or the IEI website visited for specific drivers for more sophisticated operating systems, e.g., Windows and Linux. The Watchdog Timer is provided to ensure that standalone systems can always recover from catastrophic conditions that cause the CPU to crash. This condition may have occurred by external EMI or a software bug.
~~PAGE 171~~
~~NANO-HM650 EP IC S BC NOTE: When exiting a program it is necessary to disable the Watchdog Timer, otherwise the system resets.~~
~~PAGE 172~~
~~NANO-HM650 EP IC S BC Ap p e n d ix E E Ha za rd o u s Ma te ria ls Dis c lo s u re P a g e 157~~
~~PAGE 173~~
NANO-HM650 EP IC S BC E.1 Ha za rd o u s Ma te ria l Dis c lo s ure Ta b le fo r IP B P ro d u c ts Ce rtifie d a s Ro HS Co m p lia n t Un d e r 2002/95/EC With o u t Me rc u ry The details provided in this appendix are to ensure that the product is compliant with the Peoples Republic of China (China) RoHS standards. The table below acknowledges the presences of small quantities of certain materials in the product, and is applicable to China RoHS only.
~~PAGE 174~~
NANO-HM650 EP IC S BC Part Name Toxic or Hazardous Substances and Elements Lead Mercury Cadmium Hexavalent Polybrominated Polybrominated (Pb) (Hg) (Cd) Chromium Biphenyls Diphenyl Ethers (CR(VI)) (PBB) (PBDE) Housing X O O O O X Display X O O O O X Printed Circuit X O O O O X X O O O O O X O O O O X Fan Assembly X O O O O X Power Supply X O O O O X O O O O O Board Metal Fasteners Cable Assembly Assemblies Battery O O: This toxic or haza
~~PAGE 175~~
NANO-HM650 EP IC S BC 此附件旨在确保本产品符合中国 RoHS 标准。以下表格标示此产品中某有毒物质的含量符合中国 RoHS 标准规定的限量要求。本产品上会附有”环境友好使用期限”的标签，此期限是估算这些物质”不会有泄漏或突变”的年限。本产品可能包含有较短的环境友好使用期限的可替换元件，像是电池或灯管，这些元件将会单独标示出来。部件名称有毒有害物质或元素铅汞镉六价铬多溴联苯多溴二苯醚 (Pb) (Hg) (Cd) (CR(VI)) (PBB) (PBDE) 壳体 X O O O O X 显示 X O O O O X 印刷电路板 X O O O O X 金属螺帽 X O O O O O 电缆组装 X O O O O X 风扇组装 X O O O O X 电力供应组装 X O O O O X 电池 O O O O O O O: 表示该有毒有害物质在该部件所有物质材料中的含量均在 SJ/T11363-2006 标准规定的限量要求以下。