Owner manual
Table Of Contents
- 1 Introduction
- 2 Unpacking
- 3 Connectors
- 3.1 Peripheral Interface Connectors
- 3.2 Internal Peripheral Connectors
- 3.2.1 Audio Connector
- 3.2.2 Battery Connector
- 3.2.3 CompactFlash® Slot
- 3.2.4 Digital I/O Connector
- 3.2.5 Fan Connector (CPU)
- 3.2.6 Fan Connector (System)
- 3.2.7 Front Panel Connector
- 3.2.8 Keyboard/Mouse Connector
- 3.2.9 Backlight Inverter Connector
- 3.2.10 LVDS1 LCD Connector
- 3.2.11 Parallel Port Connector
- 3.2.12 PCI-104 Connector
- 3.2.13 PCIe Mini Card Slot
- 3.2.14 12V Power Connector
- 3.2.15 SATA Drive Connectors
- 3.2.16 SATA Power Connector
- 3.2.17 Serial Port Connectors (RS-232)
- 3.2.18 Serial Port Connector (RS-232/422/485)
- 3.2.19 SMBus Connector
- 3.2.20 SPI Flash Connector
- 3.2.21 TPM Connector
- 3.2.22 USB Connectors
- 3.3 External Peripheral Interface Connector Panel
- 4 Installation
- 4.1 Anti-static Precautions
- 4.2 Installation Considerations
- 4.3 Unpacking
- 4.4 SO-DIMM Installation
- 4.5 Jumper Settings
- 4.5.1 AT Auto Button Power Select Jumper Settings
- 4.5.2 AT/ATX Power Select Jumper Settings
- 4.5.3 Clear CMOS Jumper
- 4.5.4 COM 3 Function Select Jumper
- 4.5.5 COM 3 RS-422/485 Function Select Jumper
- 4.5.6 CompactFlash® Card Setup
- 4.5.7 CompactFlash® Voltage Selection
- 4.5.8 LVDS1 Screen Resolution Selection
- 4.5.9 LVDS Voltage Selection
- 4.5.10 PCI-104 Voltage Setup
- 4.6 Chassis Installation
- 4.7 Internal Peripheral Device Connections
- 4.8 External Peripheral Interface Connection
- 4.9 Software Installation
- 5 BIOS Screens
- A BIOS Menu Options
- B One Key Recovery
- C Terminology
- D Watchdog Timer
- E Hazardous Materials Disclosure
NANO-PV-D4251/N4551/D5251 EPIC SBC
Page 105
NOTE:
Installing unsupported OS versions may cause the recovery tool to fail.
B.2 Setup Procedure for Windows
Prior to using the recovery tool to backup or restore Windows system, a few setup
procedures are required.
Step 1: Hardware and BIOS setup (see Section
B.2.1)
Step 2: Create partitions (see Section
B.2.2)
Step 3: Install operating system, drivers and system applications (see Section
B.2.3)
Step 4: Build-up recovery partition (see Section
B.2.4)
Step 5: Create factory default image (see Section
B.2.5)
Step 6: The detailed descriptions are described in the following sections. Step 0:
NOTE:
The setup procedures described below are for Microsoft Windows
operating system users. For Linux system, most setup procedures are
the same with Microsoft Windows except for several steps which is
described in Section
B.3.
B.2.1 Hardware and BIOS Setup
Step 1: Make sure the system is powered off and unplugged.
Step 2: Install a hard drive or SSD in the system. An unformatted and unpartitioned disk
is recommended.
Step 3: Connect an optical disk drive to the system and insert the recovery CD.