Owner manual
Table Of Contents
- 1 Introduction
- 2 Unpacking
- 3 Connectors
- 3.1 Peripheral Interface Connectors
- 3.2 Internal Peripheral Connectors
- 3.2.1 Audio Connector
- 3.2.2 Battery Connector
- 3.2.3 CompactFlash® Slot
- 3.2.4 Digital I/O Connector
- 3.2.5 Fan Connector (CPU)
- 3.2.6 Fan Connector (System)
- 3.2.7 Front Panel Connector
- 3.2.8 Keyboard/Mouse Connector
- 3.2.9 Backlight Inverter Connector
- 3.2.10 LVDS1 LCD Connector
- 3.2.11 Parallel Port Connector
- 3.2.12 PCI-104 Connector
- 3.2.13 PCIe Mini Card Slot
- 3.2.14 12V Power Connector
- 3.2.15 SATA Drive Connectors
- 3.2.16 SATA Power Connector
- 3.2.17 Serial Port Connectors (RS-232)
- 3.2.18 Serial Port Connector (RS-232/422/485)
- 3.2.19 SMBus Connector
- 3.2.20 SPI Flash Connector
- 3.2.21 TPM Connector
- 3.2.22 USB Connectors
- 3.3 External Peripheral Interface Connector Panel
- 4 Installation
- 4.1 Anti-static Precautions
- 4.2 Installation Considerations
- 4.3 Unpacking
- 4.4 SO-DIMM Installation
- 4.5 Jumper Settings
- 4.5.1 AT Auto Button Power Select Jumper Settings
- 4.5.2 AT/ATX Power Select Jumper Settings
- 4.5.3 Clear CMOS Jumper
- 4.5.4 COM 3 Function Select Jumper
- 4.5.5 COM 3 RS-422/485 Function Select Jumper
- 4.5.6 CompactFlash® Card Setup
- 4.5.7 CompactFlash® Voltage Selection
- 4.5.8 LVDS1 Screen Resolution Selection
- 4.5.9 LVDS Voltage Selection
- 4.5.10 PCI-104 Voltage Setup
- 4.6 Chassis Installation
- 4.7 Internal Peripheral Device Connections
- 4.8 External Peripheral Interface Connection
- 4.9 Software Installation
- 5 BIOS Screens
- A BIOS Menu Options
- B One Key Recovery
- C Terminology
- D Watchdog Timer
- E Hazardous Materials Disclosure
NANO-PV-D4251/N4551/D5251 EPIC SBC
Page 43
o When installing or configuring the motherboard, place it on an antistatic
pad. This helps to prevent potential ESD damage.
Turn all power to the NANO-PV-D4251/N4551/D5251 off:
o When working with the NANO-PV-D4251/N4551/D5251, make sure that it
is disconnected from all power supplies and that no electricity is being fed
into the system.
Before and during the installation of the NANO-PV-D4251/N4551/D5251 DO NOT:
Remove any of the stickers on the PCB board. These stickers are required for
warranty validation.
Use the product before verifying all the cables and power connectors are
properly connected.
Allow screws to come in contact with the PCB circuit, connector pins, or its
components.
4.3 Unpacking
When the NANO-PV-D4251/N4551/D5251 is unpacked, please check all the unpacking
list items listed in Chapter 3 are indeed present. If any of the unpacking list items are not
available please contact the NANO-PV-D4251/N4551/D5251 vendor reseller/vendor
where the NANO-PV-D4251/N4551/D5251 was purchased or contact an IEI sales
representative.
4.4 SO-DIMM Installation
SO-DIMM is a critical component of the NANO-PV-D4251/N4551/D5251. If it is not
installed the NANO-PV-D4251/N4551/D5251 cannot run.