Owner manual
Table Of Contents
- 1 Introduction
- 2 Unpacking
- 3 Connectors
- 3.1 Peripheral Interface Connectors
- 3.2 Internal Peripheral Connectors
- 3.2.1 Audio Connector
- 3.2.2 Battery Connector
- 3.2.3 CompactFlash® Slot
- 3.2.4 Digital I/O Connector
- 3.2.5 Fan Connector (CPU)
- 3.2.6 Fan Connector (System)
- 3.2.7 Front Panel Connector
- 3.2.8 Keyboard/Mouse Connector
- 3.2.9 Backlight Inverter Connector
- 3.2.10 LVDS1 LCD Connector
- 3.2.11 Parallel Port Connector
- 3.2.12 PCI-104 Connector
- 3.2.13 PCIe Mini Card Slot
- 3.2.14 12V Power Connector
- 3.2.15 SATA Drive Connectors
- 3.2.16 SATA Power Connector
- 3.2.17 Serial Port Connectors (RS-232)
- 3.2.18 Serial Port Connector (RS-232/422/485)
- 3.2.19 SMBus Connector
- 3.2.20 SPI Flash Connector
- 3.2.21 TPM Connector
- 3.2.22 USB Connectors
- 3.3 External Peripheral Interface Connector Panel
- 4 Installation
- 4.1 Anti-static Precautions
- 4.2 Installation Considerations
- 4.3 Unpacking
- 4.4 SO-DIMM Installation
- 4.5 Jumper Settings
- 4.5.1 AT Auto Button Power Select Jumper Settings
- 4.5.2 AT/ATX Power Select Jumper Settings
- 4.5.3 Clear CMOS Jumper
- 4.5.4 COM 3 Function Select Jumper
- 4.5.5 COM 3 RS-422/485 Function Select Jumper
- 4.5.6 CompactFlash® Card Setup
- 4.5.7 CompactFlash® Voltage Selection
- 4.5.8 LVDS1 Screen Resolution Selection
- 4.5.9 LVDS Voltage Selection
- 4.5.10 PCI-104 Voltage Setup
- 4.6 Chassis Installation
- 4.7 Internal Peripheral Device Connections
- 4.8 External Peripheral Interface Connection
- 4.9 Software Installation
- 5 BIOS Screens
- A BIOS Menu Options
- B One Key Recovery
- C Terminology
- D Watchdog Timer
- E Hazardous Materials Disclosure
NANO-PV-D4251/N4551/D5251 EPIC SBC
Page 44
4.4.1 SO-DIMM Installation
To install an SO-DIMM, please follow the steps below and refer to Figure 4-1.
Figure 4-1: SO-DIMM Installation
Step 1: Locate the SO-DIMM socket. Place the board on an anti-static mat.
Step 2: Align the SO-DIMM with the socket. Align the notch on the memory with the
notch on the memory socket.
Step 3: Insert the SO-DIMM. Push the memory in at a 20º angle. (See
Figure 4-1)
Step 4: Seat the SO-DIMM. Gently push downwards and the arms clip into place. (See
Figure 4-1)
4.5 Jumper Settings
NOTE:
A jumper is a metal bridge used to close an
electrical circuit. It consists of two or three metal
pins and a small metal clip (often protected by a
plastic cover) that slides over the pins to connect
them. To CLOSE/SHORT a jumper means
connecting the pins of the jumper with the plastic
clip and to OPEN a jumper means removing the
plastic clip from a jumper.