Owner manual
Table Of Contents
- 1 Introduction
- 2 Unpacking
- 3 Connectors
- 3.1 Peripheral Interface Connectors
- 3.2 Internal Peripheral Connectors
- 3.2.1 Audio Connector
- 3.2.2 Battery Connector
- 3.2.3 CompactFlash® Slot
- 3.2.4 Digital I/O Connector
- 3.2.5 Fan Connector (CPU)
- 3.2.6 Fan Connector (System)
- 3.2.7 Front Panel Connector
- 3.2.8 Keyboard/Mouse Connector
- 3.2.9 Backlight Inverter Connector
- 3.2.10 LVDS1 LCD Connector
- 3.2.11 Parallel Port Connector
- 3.2.12 PCI-104 Connector
- 3.2.13 PCIe Mini Card Slot
- 3.2.14 12V Power Connector
- 3.2.15 SATA Drive Connectors
- 3.2.16 SATA Power Connector
- 3.2.17 Serial Port Connectors (RS-232)
- 3.2.18 Serial Port Connector (RS-232/422/485)
- 3.2.19 SMBus Connector
- 3.2.20 SPI Flash Connector
- 3.2.21 TPM Connector
- 3.2.22 USB Connectors
- 3.3 External Peripheral Interface Connector Panel
- 4 Installation
- 4.1 Anti-static Precautions
- 4.2 Installation Considerations
- 4.3 Unpacking
- 4.4 SO-DIMM Installation
- 4.5 Jumper Settings
- 4.5.1 AT Auto Button Power Select Jumper Settings
- 4.5.2 AT/ATX Power Select Jumper Settings
- 4.5.3 Clear CMOS Jumper
- 4.5.4 COM 3 Function Select Jumper
- 4.5.5 COM 3 RS-422/485 Function Select Jumper
- 4.5.6 CompactFlash® Card Setup
- 4.5.7 CompactFlash® Voltage Selection
- 4.5.8 LVDS1 Screen Resolution Selection
- 4.5.9 LVDS Voltage Selection
- 4.5.10 PCI-104 Voltage Setup
- 4.6 Chassis Installation
- 4.7 Internal Peripheral Device Connections
- 4.8 External Peripheral Interface Connection
- 4.9 Software Installation
- 5 BIOS Screens
- A BIOS Menu Options
- B One Key Recovery
- C Terminology
- D Watchdog Timer
- E Hazardous Materials Disclosure
NANO-PV-D4251/N4551/D5251 EPIC SBC
Page 76
Î Legacy USB Support [Enabled]
Use the Legacy USB Support BIOS option to enable USB mouse and USB keyboard
support. Normally if this option is not enabled, any attached USB mouse or USB keyboard
does not become available until a USB compatible operating system is fully booted with all
USB drivers loaded. When this option is enabled, any attached USB mouse or USB
keyboard can control the system even when there is no USB driver loaded onto the
system.
Î
Enabled DEFAULT
Legacy USB support enabled
Î
Disabled
Legacy USB support disabled
Î
Auto
Legacy USB support disabled if no USB devices are
connected
5.3.6 Super IO Configuration
Use the Super IO Configuration menu (BIOS Menu 8) to set or change the
configurations for the FDD controllers, parallel ports and serial ports.
Aptio Setup Utility – Copyright (C) 2010 American Megatrends, Inc.
Advanced
Super IO Configuration
Super IO Chip Finteck F81865
> Serial Port 0 Configuration
> Serial Port 1 Configuration
> Serial Port 2 Configuration
> Serial Port 3 Configuration
> Serial Port 4 Configuration
> IrDA Configuration
> Parallel Port Configuration
S
et Parameters of Serial
Port 0 (COMA)
---------------------
ÅÆ
: Select Screen
↑ ↓: Select Item
Enter Select
F1 General Help
F2 Previous Values
F3 Optimized
Defaults
F4 Save
ESC Exit
Version 2.02.1205. Copyright (C) 2010 American Megatrends, Inc.
BIOS Menu 8: Super IO Configuration