Manual

ManualsBrandsIEI Integration ManualsHardwareNANO-PV-D4252_N4552_D5252

NANO-PV-D4252/N4552/D5252 EPIC SBC

Page i

IEI Technology Corp.

User Manual

NANO-PV-D4252/N4552/D5252

MODEL:

EPIC Motherboard with Intel®

tom™ processor

D425/N455/D525, VGA, Dual LVDS, GbE LAN, Eight USB 2.0,

Two SATA 3Gb/s, Four RS-232, RS-232/422/485, PCIe mini,

PCI-104, RoHS

Rev. 1.05 – 31 December, 2011

Summary of content (148 pages)

PAGE 1
NANO-PV-D4252/N4552/D5252 EPIC SBC IEI Technology Corp. MODEL: NANO-PV-D4252/N4552/D5252 EPIC Motherboard with Intel® Atom™ processor D425/N455/D525, VGA, Dual LVDS, GbE LAN, Eight USB 2.0, Two SATA 3Gb/s, Four RS-232, RS-232/422/485, PCIe mini, PCI-104, RoHS User Manual Page i Rev. 1.
PAGE 2
NANO-PV-D4252/N4552/D5252 EPIC SBC Revision Date Version Changes 31 December, 2011 1.05 Added note to Section 3.1.3 and Section 4.8 24 August, 2011 1.04 Minor revision to pin definitions in the following sections: 4.5.9 LVDS1 Screen Resolution Selection 4.5.10 LVDS2 Screen Resolution Selection 17 June, 2011 1.03 Minor revision to pin definitions in section 3.2.16 Power Connector 18 April, 2011 1.02 Updated Table 4-7, 4-8, and 4-10 jumper settings.
PAGE 3
NANO-PV-D4252/N4552/D5252 EPIC SBC Copyright COPYRIGHT NOTICE The information in this document is subject to change without prior notice in order to improve reliability, design and function and does not represent a commitment on the part of the manufacturer. In no event will the manufacturer be liable for direct, indirect, special, incidental, or consequential damages arising out of the use or inability to use the product or documentation, even if advised of the possibility of such damages.
PAGE 4
NANO-PV-D4252/N4552/D5252 EPIC SBC Table of Contents 1 INTRODUCTION.......................................................................................................... 1 1.1 INTRODUCTION........................................................................................................... 2 1.2 CONNECTORS ............................................................................................................. 3 1.3 DIMENSIONS ...................................................................
PAGE 5
NANO-PV-D4252/N4552/D5252 EPIC SBC 3.2.13 Parallel Port Connector ................................................................................ 25 3.2.14 PCI-104 Connector........................................................................................ 26 3.2.15 PCIe Mini Card Slot ...................................................................................... 28 3.2.16 Power Connector (+12 V, power supply)....................................................... 29 3.2.
PAGE 6
NANO-PV-D4252/N4552/D5252 EPIC SBC 4.5.11 LVDS Voltage Selection.................................................................................. 54 4.5.12 PCI-104 Voltage Setup ................................................................................... 55 4.6 CHASSIS INSTALLATION ............................................................................................ 56 4.6.1 Airflow..............................................................................................................
PAGE 7
NANO-PV-D4252/N4552/D5252 EPIC SBC 5.3.7 H/W Monitor .................................................................................................... 85 5.3.8 Serial Port Console Redirection ...................................................................... 87 5.4 CHIPSET ................................................................................................................... 88 5.4.1 Host Bridge Configuration ..............................................................................
PAGE 8
NANO-PV-D4252/N4552/D5252 EPIC SBC List of Figures Figure 1-1: NANO-PV-D4252/N4552/D5252 ..................................................................................2 Figure 1-2: Connectors ..................................................................................................................3 Figure 1-3: NANO-PV-D4252/N4552/D5252 Dimensions (mm) ...................................................4 Figure 1-4: Data Flow Block Diagram ........................................................
PAGE 9
NANO-PV-D4252/N4552/D5252 EPIC SBC Figure 3-27: PS/2 Pinout and Configuration ..............................................................................37 Figure 3-28: VGA Connector .......................................................................................................39 Figure 4-1: SO-DIMM Installation ................................................................................................44 Figure 4-2: AT Auto Button Select Jumper Settings.......................................
PAGE 10
NANO-PV-D4252/N4552/D5252 EPIC SBC Figure B-10: Symantec Ghost Path ......................................................................................... 112 Figure B-11: Select a Local Source Drive ............................................................................... 112 Figure B-12: Select a Source Partition from Basic Drive ...................................................... 112 Figure B-13: File Name to Copy Image to ......................................................................
PAGE 11
NANO-PV-D4252/N4552/D5252 EPIC SBC List of Tables Table 1-1: Technical Specifications..............................................................................................7 Table 3-1: Peripheral Interface Connectors ...............................................................................15 Table 3-2: Rear Panel Connectors ..............................................................................................15 Table 3-3: Audio Connector Pinouts ........................................
PAGE 12
NANO-PV-D4252/N4552/D5252 EPIC SBC Table 3-30: VGA Connector Pinouts...........................................................................................39 Table 4-1: Jumpers .......................................................................................................................45 Table 4-2: AT Auto Button Power Select Jumper Settings ......................................................46 Table 4-3: AT/ATX Power Select Jumper Settings ..................................................
PAGE 13
NANO-PV-D4252/N4552/D5252 EPIC SBC BIOS Menus BIOS Menu 1: Main .......................................................................................................................72 BIOS Menu 2: Advanced ..............................................................................................................73 BIOS Menu 3: ACPI Settings .......................................................................................................74 BIOS Menu 4: TPM Configuration ..........................
PAGE 14
NANO-PV-D4252/N4552/D5252 EPIC SBC Page xiv
PAGE 15
NANO-PV-D4252/N4552/D5252 EPIC SBC Chapter 1 1 Introduction Page 1
PAGE 16
NANO-PV-D4252/N4552/D5252 EPIC SBC 1.1 Introduction Figure 1-1: NANO-PV-D4252/N4552/D5252 The NANO-PV-D4252/N4552/D5252 EPIC motherboard is a Intel® Atom™ processor D525, D425 or N455 platform. Up to one 2.0 GB 800 MHz or 667 MHz DDR3 SDRAM SO-DIMM is supported by the NANO-PV-D4252/N4552/D5252. The integrated Intel® ICH8M Chipset supports a GbE LAN port through the Realtek RTL8111E Ethernet controller (with ASF 2.0 support).
PAGE 17
NANO-PV-D4252/N4552/D5252 EPIC SBC 1.2 Connectors The connectors on the NANO-PV-D4252/N4552/D5252 are shown in the figure below.
PAGE 18
NANO-PV-D4252/N4552/D5252 EPIC SBC 1.
PAGE 19
NANO-PV-D4252/N4552/D5252 EPIC SBC 1.4 Data Flow Figure 1-4 shows the data flow between the two on-board chipsets and other components 6 installed on the motherboard and described in the following sections of this chapter.
PAGE 20
NANO-PV-D4252/N4552/D5252 EPIC SBC 1.5 Technical Specifications NANO-PV-D4252/N4552/D5252 technical specifications are listed in table below. Specification NANO-PV-D4252/N4552/D5252 Form Factor EPIC CPU options Intel® Atom™ processor D525, 1.8 GHz/1 MB L2 cache Intel® Atom™ processor D425, 1.8 GHz/512 KB L2 cache Intel® Atom™ processor N455, 1.66 GHz/512 KB L2 cache Express Chipset Intel® ICH8M Memory One 204-pin SO-DIMM sockets support one 800/667 MHz 2.0 GB (max.) DDR3 SDRAM SO-DIMM (system max.
PAGE 21
NANO-PV-D4252/N4552/D5252 EPIC SBC Specification NANO-PV-D4252/N4552/D5252 Serial Ports One RS-232 serial port Three RS-232 via four 10-pin headers One RS-232/422/485 via 14–pin header USB 2.0/1.1 Ports Two external USB ports Six internal USB ports via three 8-pin headers Parallel Ports One LPT connector via 26-pin header Storage Serial ATA Two SATA 3.
PAGE 22
NANO-PV-D4252/N4552/D5252 EPIC SBC Chapter 2 2 Unpacking Page 8
PAGE 23
NANO-PV-D4252/N4552/D5252 EPIC SBC 2.1 Anti-static Precautions WARNING! Static electricity can destroy certain electronics. Make sure to follow the ESD precautions to prevent damage to the product, and injury to the user. Make sure to adhere to the following guidelines:  Wear an anti-static wristband: Wearing an anti-static wristband can prevent electrostatic discharge.  Self-grounding: Touch a grounded conductor every few minutes to discharge any excess static buildup.
PAGE 24
NANO-PV-D4252/N4552/D5252 EPIC SBC 2.3 Packing List NOTE: If any of the components listed in the checklist below are missing, do not proceed with the installation. Contact the IEI reseller or vendor the NANO-PV-D4252/N4552/D5252 was purchased from or contact an IEI sales representative directly by sending an email to sales@iei.com.tw.
PAGE 25
NANO-PV-D4252/N4552/D5252 EPIC SBC 1 Dual USB cable (w bracket) (P/N:CB-USB02A-RS) 1 Mini jumper pack (2.0mm) (P/N: 33100-000033-RS) 1 Utility CD 1 Quick Installation Guide 2.3.
PAGE 26
NANO-PV-D4252/N4552/D5252 EPIC SBC Chapter 3 3 Connectors Page 12
PAGE 27
NANO-PV-D4252/N4552/D5252 EPIC SBC 3.1 Peripheral Interface Connectors This chapter details all the jumpers and connectors. 3.1.1 NANO-PV-D4252/N4552/D5252 Layout The figures below show all the connectors and jumpers.
PAGE 28
NANO-PV-D4252/N4552/D5252 EPIC SBC 3.1.2 Peripheral Interface Connectors The table below lists all the connectors on the board.
PAGE 29
NANO-PV-D4252/N4552/D5252 EPIC SBC Serial ATA (SATA) drive connector 7-pin SATA SATA1 Serial ATA (SATA) drive connector 7-pin SATA SATA2 SATA power connector 2-pin wafer PWR1 SMBus connector 4-pin wafer CN1 USB connector 8-pin header USB0_1 USB connector 8-pin header USB2_3 USB connector 8-pin header USB4_5 Table 3-1: Peripheral Interface Connectors 3.1.
PAGE 30
NANO-PV-D4252/N4552/D5252 EPIC SBC 3.2 Internal Peripheral Connectors The section describes all of the connectors on the NANO-PV-D4252/N4552/D5252. 3.2.1 Audio Connector CN Label: AUDIO1 CN Type: 10-pin header (2x5) CN Location: See Figure 3-2 CN Pinouts: See Table 3-3 The audio connector is connected to external audio devices including speakers and microphones for the input and output of audio signals to and from the system. Figure 3-2: Audio Connector Location PIN NO. DESCRIPTION PIN NO.
PAGE 31
NANO-PV-D4252/N4552/D5252 EPIC SBC This is connected to the system battery. The battery provides power to the system clock to retain the time when power is turned off. Figure 3-3: Battery Connector Location Pin Description 1 Battery+ 2 Ground Table 3-4: Battery Connector Pinouts 3.2.3 CompactFlash® Slot CN Label: CF1 CN Type: CompactFlash® card slot CN Location: See Figure 3-4 CN Pinouts: See Table 3-5 A CompactFlash® Type I/II card can be used in this slot.
PAGE 32
NANO-PV-D4252/N4552/D5252 EPIC SBC Pin Description Pin Description 2 DATA 3 27 DATA 11 3 DATA 4 28 DATA 12 4 DATA 5 29 DATA 13 5 DATA 6 30 DATA 14 6 DATA 7 31 DATA 15 7 HDC_CS0# 32 HDC_CS1 8 GROUND 33 N/C 9 GROUND 34 IOR# 10 GROUND 35 IOW# 11 GROUND 36 VCC_CF 12 GROUND 37 IRQ14 13 VCC_CF 38 VCC_CF 14 GROUND 39 CSEL 15 GROUND 40 N/C 16 GROUND 41 HDD_RESET 17 GROUND 42 IORDY 18 SA2 43 SDREQ 19 SA1 44 SDACK# 20 SA0 45 HDD_ACTIVE# 2
PAGE 33
NANO-PV-D4252/N4552/D5252 EPIC SBC The digital I/O connector provides programmable input and output for external devices. The digital I/O provides 4-bit output and 4-bit input. Figure 3-5: Digital I/O Connector Locations Pin Description Pin Description 1 GND 2 +5V 3 Output 3 4 Output 2 5 Output 1 6 Output 0 7 Input 3 8 Input 2 9 Input 1 10 Input 0 Table 3-6: Digital I/O Connector Pinouts 3.2.
PAGE 34
NANO-PV-D4252/N4552/D5252 EPIC SBC Pin Description 1 FANIO1 2 POWER 3 GND Table 3-7: CPU Fan Connector Pinouts 3.2.6 Fan Connector (System) CN Label: SYS_FAN1 CN Type: 3-pin wafer (1x3) CN Location: See Figure 3-7 CN Pinouts: See Table 3-8 6 6 The cooling fan connector provides a 12V, 500mA current to the cooling fan. The connector has a "rotation" pin to get rotation signals from fans and notify the system so the system BIOS can recognize the fan speed.
PAGE 35
NANO-PV-D4252/N4552/D5252 EPIC SBC CN Type: 8-pin header (2x4) CN Location: See Figure 3-8 CN Pinouts: See Table 3-9 The front panel connector connects to external switches and indicators to monitor and controls the motherboard.
PAGE 36
NANO-PV-D4252/N4552/D5252 EPIC SBC The keyboard/mouse connector connects to a PS/2 Y-cable that can be connected to a PS/2 keyboard and mouse. Figure 3-9: Keyboard/Mouse Connector Location Pin Description 1 +5 VCC 2 MS DATA 3 MS CLK 4 KB DATA 5 KB CLK 6 GROUND Table 3-10: Keyboard/Mouse Connector Pinouts 3.2.
PAGE 37
NANO-PV-D4252/N4552/D5252 EPIC SBC Pin Description 1 BL_ADJ 2 GROUND 3 +12 V 4 GROUND 5 BACKLIGHT ENABLE Table 3-11: Backlight Inverter Connector Pinouts 3.2.10 LVDS Backlight Adjustment (LVDS2) CN Label: KEY1 CN Type: 9-pin header CN Location: See Figure 3-11 CN Pinouts: See Table 3-12 Interfaces to the LPC interface on the Southbridge.
PAGE 38
NANO-PV-D4252/N4552/D5252 EPIC SBC CN Type: 20-pin crimp (2x10) CN Location: See Figure 3-12 CN Pinouts: See Table 3-14 The LVDS1 connector is for an LCD panel connected to the board.
PAGE 39
NANO-PV-D4252/N4552/D5252 EPIC SBC The LVDS2 connector is for an LCD panel connected to the board.
PAGE 40
NANO-PV-D4252/N4552/D5252 EPIC SBC The parallel port connector connects to a parallel port connector interface or some other parallel port device such as a printer.
PAGE 41
NANO-PV-D4252/N4552/D5252 EPIC SBC Figure 3-15: PCI-104 Connector Location Pin Row A Row B Row C Row D 1 GND/5 V TBD1 5V AD00 2 VI/O1 AD02 AD01 +5 V 3 AD05 GND AD04 AD03 4 C/BE0# AD07 GND AD06 5 GND AD09 AD08 GND 6 AD11 VI/O2 AD10 M66EN 7 AD14 AD13 GND AD12 8 +3.3 V C/BE1# AD15 +3.3 V 9 SERR# GND SB0# PAR 10 GND PERR# +3.3 V SDONE 11 STOP# +3.3 V LOCK# GND 12 +3.3 V TRDY# GND DEVSEL# 13 FRAME# GND IRDY# +3.3 V 14 GND AD16 +3.
PAGE 42
NANO-PV-D4252/N4552/D5252 EPIC SBC Pin Row A Row B Row C Row D 26 +5 V CLK0 GND CLK1 27 CLK2 +5 V CLK3 GND 28 GND INTD# +5 V RST# 29 +12 V INTA# INTB# INTC# 30 -12 V TBD2 TBD GND/3.3 V Table 3-16: PCI-104 Connector Pinouts 3.2.15 PCIe Mini Card Slot CN Label: MINI-PCIE1 CN Type: PCIe Mini card slot CN Location: See Figure 3-16 CN Pinouts: See Table 3-17 6 The PCIe Mini card slot is for installing PCIe Mini expansion cards.
PAGE 43
NANO-PV-D4252/N4552/D5252 EPIC SBC Pin Description Pin Description 19 LPC 20 VCC3 21 GND 22 PCIRST# 23 PERN2 24 3VDual 25 PERP2 26 GND 27 GND 28 1.5 V 29 GND 30 SMBCLK 31 PETN2 32 SMBDATA 33 PETP2 34 GND 35 GND 36 USBD- 37 GND 38 USBD+ 39 VCC3 40 GND 41 VCC3 42 N/C 43 GND 44 RF_LINK# 45 SATATXP1 46 BLUELED# 47 SATATXN1 48 1.5 V 49 SATARXN1 50 GND 51 SATARXP1 52 VCC3 Table 3-17: PCIe Mini Card Slot Pinouts 3.2.
PAGE 44
NANO-PV-D4252/N4552/D5252 EPIC SBC Figure 3-17: CPU 12V Power Connector Location PIN NO. DESCRIPTION PIN NO. DESCRIPTION 1 GND 2 GND 3 +12V 4 +12V Table 3-18: CPU 12V Power Connector Pinouts 3.2.17 SATA Drive Connectors CN Label: SATA1, SATA2 CN Type: 7-pin SATA drive connectors CN Location: See Figure 3-18 CN Pinouts: See Table 3-19 6 6 The two SATA 3Gb/s drive connectors are each connected to a SATA 3Gb/s drive. The SATA 3Gb/s drives transfer data at speeds as high as 3.0 Gb/s.
PAGE 45
NANO-PV-D4252/N4552/D5252 EPIC SBC 4 GND 5 RX- 6 RX+ 7 GND Table 3-19: SATA Drive Connector Pinouts 3.2.18 SATA Power Connector CN Label: PWR1 CN Type: 2-pin wafer (1x2) CN Location: See Figure 3-19 CN Pinouts: See Table 3-20 The SATA Power Connector provides +5V power output to the SATA connectors. Figure 3-19: SATA Power Connector Locations PIN NO. DESCRIPTION 1 +5V 2 GND Table 3-20: SATA Power Connector Pinouts 3.2.
PAGE 46
NANO-PV-D4252/N4552/D5252 EPIC SBC These connectors provide RS-232 communications. Figure 3-20: COM Connector Pinout Locations PIN NO. DESCRIPTION PIN NO.
PAGE 47
NANO-PV-D4252/N4552/D5252 EPIC SBC 3.2.20 Serial Port Connector (RS-232/422/485) CN Label: COM3 CN Type: 14-pin header (2x7) CN Location: See Figure 3-21 CN Pinouts: See Table 3-22 Used for RS-232/422/485 communications. Figure 3-21: Serial Port Connector Location PIN NO. DESCRIPTION PIN NO.
PAGE 48
NANO-PV-D4252/N4552/D5252 EPIC SBC Figure 3-22: SMBus Connector Locations PIN NO. DESCRIPTION 1 GND 2 SMBDATA 3 SMBCLK 4 VCC5S Table 3-23: SMBus Connector Pinouts 3.2.22 SPI Flash Connector CN Label: SPI1 CN Type: 8-pin header (2x4) CN Location: See Figure 3-23 CN Pinouts: See Table 3-24 The 8-pin SPI Flash connector is used to flash the BIOS.
PAGE 49
NANO-PV-D4252/N4552/D5252 EPIC SBC Pin Description Pin Description 5 SO 6 SI 7 NC 8 NC Table 3-24: SPI Flash Connector Pinouts 3.2.23 USB Connectors CN Label: USB0_1, USB2_3, USB4_5 CN Type: 8-pin header (2x4) CN Location: See Figure 3-24 CN Pinouts: See Table 3-25 The USB connectors connect to USB devices. Each pin header provides two USB ports. Figure 3-24: USB Connector Pinout Locations PIN NO. DESCRIPTION PIN NO.
PAGE 50
NANO-PV-D4252/N4552/D5252 EPIC SBC 3.3 External Peripheral Interface Connector Panel Figure 3-25 shows the NANO-PV-D4252/N4552/D5252 external peripheral interface 6 connector (EPIC) panel. The NANO-PV-D4252/N4552/D5252 EPIC panel consists of the following:  1 x Ethernet connector  1 x Keyboard/Mouse  1 x Serial port (RS-232)  2 x USB connectors  1 x VGA connector Figure 3-25: NANO-PV-D4252/N4552/D5252 External Peripheral Interface Connector 3.3.
PAGE 51
NANO-PV-D4252/N4552/D5252 EPIC SBC Table 3-26: LAN Pinouts The RJ-45 Ethernet connector has two status LEDs, one green and one yellow. The green LED indicates activity on the port and the yellow LED indicates the speed. See Table 6 3-27.
PAGE 52
NANO-PV-D4252/N4552/D5252 EPIC SBC Pin Description 1 KB DATA 2 MS DATA 3 GND 4 VCC 5 KB CLOCK 6 MS CLOCK Table 3-28: Keyboard Connector Pinouts 3.3.3 USB Connectors CN Label: USB6_7 CN Type: USB port CN Location: See Figure 3-25 CN Pinouts: See Table 3-29 6 6 The NANO-PV-D4252/N4552/D5252 has four external USB 2.0 ports. The ports connect to both USB 2.0 and USB 1.1 devices. PIN NO. DESCRIPTION PIN NO.
PAGE 53
NANO-PV-D4252/N4552/D5252 EPIC SBC Connects to a monitor that accepts a standard VGA input.
PAGE 54
NANO-PV-D4252/N4552/D5252 EPIC SBC Chapter 4 4 Installation Page 40
PAGE 55
NANO-PV-D4252/N4552/D5252 EPIC SBC 4.1 Anti-static Precautions WARNING: Failure to take ESD precautions during the installation of the NANO-PV-D4252/N4552/D5252 may result in permanent damage to the NANO-PV-D4252/N4552/D5252 and severe injury to the user. Electrostatic discharge (ESD) can cause serious damage to electronic components, including the NANO-PV-D4252/N4552/D5252. Dry climates are especially susceptible to ESD.
PAGE 56
NANO-PV-D4252/N4552/D5252 EPIC SBC 4.2 Installation Considerations NOTE: The following installation notices and installation considerations should be read and understood before the NANO-PV-D4252/N4552/D5252 is installed. All installation notices pertaining to the installation of the NANO-PV-D4252/N4552/D5252 should be strictly adhered to. Failing to adhere to these precautions may lead to severe damage of the NANO-PV-D4252/N4552/D5252 and injury to the person installing the motherboard. 4.2.
PAGE 57
NANO-PV-D4252/N4552/D5252 EPIC SBC  Turn all power to the NANO-PV-D4252/N4552/D5252 off: o When working with the NANO-PV-D4252/N4552/D5252, make sure that it is disconnected from all power supplies and that no electricity is being fed into the system. Before and during the installation of the NANO-PV-D4252/N4552/D5252 DO NOT:  Remove any of the stickers on the PCB board. These stickers are required for warranty validation.
PAGE 58
NANO-PV-D4252/N4552/D5252 EPIC SBC 4.4.1 SO-DIMM Installation To install an SO-DIMM, please follow the steps below and refer to Figure 4-1. Figure 4-1: SO-DIMM Installation Step 1: Locate the SO-DIMM socket. Place the board on an anti-static mat. Step 2: Align the SO-DIMM with the socket. Align the notch on the memory with the notch on the memory socket. Step 3: Insert the SO-DIMM. Push the memory in at a 20º angle. (See Figure 4-1) Step 4: Seat the SO-DIMM.
PAGE 59
NANO-PV-D4252/N4552/D5252 EPIC SBC Before the NANO-PV-D4252/N4552/D5252 is installed in the system, the jumpers must be set in accordance with the desired configuration. The jumpers on the NANO-PV-D4252/N4552/D5252 are listed in Table 4-1.
PAGE 60
NANO-PV-D4252/N4552/D5252 EPIC SBC Setting Description Open Use ATX power Table 4-2: AT Auto Button Power Select Jumper Settings Figure 4-2: AT Auto Button Select Jumper Settings 4.5.2 AT/ATX Power Select Jumper Settings Jumper Label: J_ATXCTL1 Jumper Type: 3-pin header (1x3) Jumper Settings: See Table 4-3 Jumper Location: See Figure 4-3 The AT/ATX Power Select jumper specifies the systems power mode as AT or ATX. AT/ATX Power Select jumper settings are shown in Table 4-3.
PAGE 61
NANO-PV-D4252/N4552/D5252 EPIC SBC Figure 4-3: AT/ATX Power Select Jumper Location 4.5.3 Clear CMOS Jumper Jumper Label: J_CMOS1 Jumper Type: 3-pin header (1x3) Jumper Settings: See Table 4-4 Jumper Location: See Figure 4-4 6 6 If the NANO-PV-D4252/N4552/D5252 fails to boot due to improper BIOS settings, the clear CMOS jumper clears the CMOS data and resets the system BIOS information.
PAGE 62
NANO-PV-D4252/N4552/D5252 EPIC SBC Clear CMOS Description Short 1 - 2 Keep CMOS Setup Short 2 - 3 Clear CMOS Setup Default Table 4-4: Clear CMOS Jumper Settings The location of the clear CMOS jumper is shown in Figure 4-4 below. 6 Figure 4-4: Clear CMOS Jumper 4.5.
PAGE 63
NANO-PV-D4252/N4552/D5252 EPIC SBC Figure 4-5: COM 3 Function Select Jumper Location 4.5.5 COM 3 RS-422/485 Function Select Jumper Jumper Label: J6 Jumper Type: 6-pin header Jumper Settings: See Table 4-5 Jumper Location: See Figure 4-5 The COM 3 Function Select jumper sets the communication protocol used by the second serial communications port (COM 3) as RS-422 or RS-485. The COM 3 Function Select settings are shown below.
PAGE 64
NANO-PV-D4252/N4552/D5252 EPIC SBC Figure 4-6: COM 3 RS-422/485 Function Select Jumper Location 4.5.6 COM 3 RS-422/485 Termination Select Jumpers Jumper Label: J9 and J10 Jumper Type: 2-pin header Jumper Settings: See Table 4-5 and Table 4-7 Jumper Location: See Figure 4-7 The COM 3 RS-422 and RS-485 Termination Select jumpers enable or disable the termination used by the serial COM 3 communications port as 120 ohm.
PAGE 65
NANO-PV-D4252/N4552/D5252 EPIC SBC Figure 4-7: COM 3 RS-422 and RS-485 Termination Select Jumper Location 4.5.7 CompactFlash® Card Setup Jumper Label: JCF1 Jumper Type: 2-pin header Jumper Settings: See Table 4-9 Jumper Location: See Figure 4-4 The CompactFlash® slot is connected through an IDE connection. This jumper sets the CompactFlash® card as the master or slave IDE device.
PAGE 66
NANO-PV-D4252/N4552/D5252 EPIC SBC 4.5.8 CompactFlash® Voltage Selection WARNING: Incorrect voltages can destroy the CF card. Make sure to select a voltage that matches the voltage required by the CF card. Jumper Label: J_VCF1 Jumper Type: 2-pin header Jumper Settings: See Table 4-10 Jumper Location: See Figure 4-9 The CompactFlash® voltage selection jumper sets the voltage of the power supplied to the CF card. Setting Description Short 1-2 +5 V Short 2-3 +3.
PAGE 67
NANO-PV-D4252/N4552/D5252 EPIC SBC The LVDS1 Screen Resolution Selection jumper allows the LVDS screen voltage to be set. The LVDS1 Screen Resolution Selection jumper settings are shown in Table 4-13. Pin Description Open 640 x 480 1-2 800 x 600 3-4 1024 x 768 1-2 and 3-4 1280 x 1024 5-6 1366 x 768 1-2 and 5-6 1920 x 1080 Table 4-11: LVDS1 Screen Resolution Jumper Settings Figure 4-10: LVDS1 Screen Resolution Jumper Location 4.5.
PAGE 68
NANO-PV-D4252/N4552/D5252 EPIC SBC Pin Description 5-6 1366 x 768 1-2 and 5-6 1920 x 1080 Table 4-12: LVDS2 Screen Resolution Jumper Settings Figure 4-11: LVDS2 Screen Resolution Jumper Location 4.5.11 LVDS Voltage Selection WARNING: Incorrect voltages can destroy the LCD panel. Make sure to select a voltage that matches the voltage required by the LCD panel.
PAGE 69
NANO-PV-D4252/N4552/D5252 EPIC SBC Figure 4-12: LVDS Voltage Selection Jumper Locations 4.5.12 PCI-104 Voltage Setup Jumper Label: JP1 Jumper Type: 3-pin header Jumper Settings: See Table 4-14 Jumper Location: See Figure 4-13 This jumper selects the voltage supplied to the PCI-104 expansion module. Setting Description 1-2 +5.0 V 2-3 +3.
PAGE 70
NANO-PV-D4252/N4552/D5252 EPIC SBC 4.6 Chassis Installation 4.6.1 Airflow WARNING: Airflow is critical to the cooling of the CPU and other onboard components. The chassis in which the NANO-PV-D4252/N4552/D5252 must have air vents to allow cool air to move into the system and hot air to move out. The NANO-PV-D4252/N4552/D5252 must be installed in a chassis with ventilation holes on the sides allowing airflow to travel through the heat sink surface.
PAGE 71
NANO-PV-D4252/N4552/D5252 EPIC SBC Step 1: Locate the power cable. The power cable is shown in the packing list in Chapter 3. Step 2: Connect the Power Cable to the Motherboard. Connect the 4-pin (2x2) Molex type power cable connector to the AT/ATX power connector on the motherboard. See Figure 4-14. Figure 4-14: Power Cable to Motherboard Connection Step 3: Connect Power Cable to Power Supply. Connect one of the 4-pin (1x4) Molex type power cable connectors to an AT/ATX power supply. See Figure 4-15.
PAGE 72
NANO-PV-D4252/N4552/D5252 EPIC SBC Figure 4-15: Connect Power Cable to Power Supply 4.7.2 Audio Kit Installation The Audio Kit that came with the NANO-PV-D4252/N4552/D5252 connects to the audio connector on the NANO-PV-D4252/N4552/D5252. The audio kit consists of three audio jacks. Mic-in connects to a microphone. Line-in provides a stereo line-level input to connect to the output of an audio device. Line-out, a stereo line-level output, connects to two amplified speakers.
PAGE 73
NANO-PV-D4252/N4552/D5252 EPIC SBC Figure 4-16: Audio Kit Cable Connection Step 3: Connect the audio devices. Connect speakers to the line-out audio jack. Connect the output of an audio device to the line-in audio jack. Connect a microphone to the mic-in audio jack.Step 0: 4.7.3 Single RS-232 Cable (w/o Bracket) The single RS-232 cable consists of one serial port connector attached to a serial communications cable that is then attached to a D-sub 9 male connector.
PAGE 74
NANO-PV-D4252/N4552/D5252 EPIC SBC Figure 4-17: Single RS-232 Cable Installation Step 3: Secure the bracket. The single RS-232 connector has two retention screws that must be secured to a chassis or bracket. Step 4: Connect the serial device. Once the single RS-232 connector is connected to a chassis or bracket, a serial communications device can be connected to the system. Step 0: 4.
PAGE 75
NANO-PV-D4252/N4552/D5252 EPIC SBC The following external peripheral devices can be connected to the external peripheral interface connectors.  Keyboard and mouse  RJ-45 Ethernet cable connector  Serial devices  USB devices  VGA monitor To install these devices, connect the corresponding cable connector from the actual device to the corresponding NANO-PV-D4252/N4552/D5252 external peripheral interface connector making sure the pins are properly aligned. 4.8.
PAGE 76
NANO-PV-D4252/N4552/D5252 EPIC SBC Figure 4-18: LAN Connection Step 3: Insert the LAN cable RJ-45 connector. Once aligned, gently insert the LAN cable RJ-45 connector into the on-board RJ-45 connector. Step 0: 4.8.2 PS/2 Y-Cable Connection The NANO-PV-D4252/N4552/D5252 has a PS/2 connector on the external peripheral interface panel. The dual PS/2 connector is connected to the PS/2 Y-cable that came with the NANO-PV-D4252/N4552/D5252.
PAGE 77
NANO-PV-D4252/N4552/D5252 EPIC SBC Figure 4-19: PS/2 Keyboard/Mouse Connector Step 3: Connect the keyboard and mouse. Connect the keyboard and mouse to the appropriate connector. The keyboard and mouse connectors can be distinguished from each other by looking at the small graphic at the top of the connector. Step 0: 4.8.3 Serial Device Connection The NANO-PV-D4252/N4552/D5252 has a single female DB-9 connector on the external peripheral interface panel for a serial device.
PAGE 78
NANO-PV-D4252/N4552/D5252 EPIC SBC Figure 4-20: Serial Device Connector Step 3: Secure the connector. Secure the serial device connector to the external interface by tightening the two retention screws on either side of the connector. Step 0: 4.8.4 USB Connection (Dual Connector) The external USB Series "A" receptacle connectors provide easier and quicker access to external USB devices. Follow the steps below to connect USB devices to the NANO-PV-D4252/N4552/D5252.
PAGE 79
NANO-PV-D4252/N4552/D5252 EPIC SBC Figure 4-21: USB Connector 4.8.5 VGA Monitor Connection The NANO-PV-D4252/N4552/D5252 has a single female DB-15 connector on the external peripheral interface panel. The DB-15 connector is connected to a CRT or VGA monitor. To connect a monitor to the NANO-PV-D4252/N4552/D5252, please follow the instructions below. Step 1: Locate the female DB-15 connector. The location of the female DB-15 connector is shown in Chapter 3. Step 2: Align the VGA connector.
PAGE 80
NANO-PV-D4252/N4552/D5252 EPIC SBC Figure 4-22: VGA Connector Step 4: Secure the connector. Secure the DB-15 VGA connector from the VGA monitor to the external interface by tightening the two retention screws on either side of the connector. Step 0: 4.9 Software Installation All the drivers for the NANO-PV-D4252/N4552/D5252 are on the CD that came with the system. To install the drivers, please follow the steps below. Step 1: Insert the CD into a CD drive connected to the system.
PAGE 81
NANO-PV-D4252/N4552/D5252 EPIC SBC Figure 4-23: Introduction Screen Step 3: Click NANO-PV-D4252/N4552/D5252. Step 4: A new screen with a list of available drivers appears (Figure 4-24).
PAGE 82
NANO-PV-D4252/N4552/D5252 EPIC SBC Figure 4-24: Available Drivers Step 5: Install all of the necessary drivers in this menu.
PAGE 83
NANO-PV-D4252/N4552/D5252 EPIC SBC Chapter 5 5 BIOS Screens Page 69
PAGE 84
NANO-PV-D4252/N4552/D5252 EPIC SBC 5.1 Introduction The BIOS is programmed onto the BIOS chip. The BIOS setup program allows changes to certain system settings. This chapter outlines the options that can be changed. 5.1.1 Starting Setup The AMI BIOS is activated when the computer is turned on. The setup program can be activated in one of two ways. 1. Press the DELETE key as soon as the system is turned on or 2. Press the DELETE key when the “Press Del to enter SETUP” message appears on the screen. 0.
PAGE 85
NANO-PV-D4252/N4552/D5252 EPIC SBC Key Function F4 key Save all the CMOS changes Esc key Main Menu – Quit and not save changes into CMOS Status Page Setup Menu and Option Page Setup Menu -Exit current page and return to Main Menu Table 5-1: BIOS Navigation Keys 5.1.3 Getting Help When F1 is pressed a small help window describing the appropriate keys to use and the possible selections for the highlighted item appears. To exit the Help Window press ESC or the F1 key again. 5.1.
PAGE 86
NANO-PV-D4252/N4552/D5252 EPIC SBC 5.2 Main The Main BIOS menu (BIOS Menu 1) appears when the BIOS Setup program is entered. The Main menu gives an overview of the basic system information. Aptio Setup Utility – Copyright (C) 2010 American Megatrends, Inc. Main Advanced Chipset Boot Security Save & Exit BIOS Information BIOS Vendor Core Version Compliency Project Version Build Date American Megatrends 4.6.4.0 0.20 UEFI 2.0 SA24AR11.ROM 09/13/2010 20:29:21 Set the Time.
PAGE 87
NANO-PV-D4252/N4552/D5252 EPIC SBC  System Time [xx:xx:xx] Use the System Time option to set the system time. Manually enter the hours, minutes and seconds. 5.3 Advanced Use the Advanced menu (BIOS Menu 2) to configure the CPU and peripheral devices through the following sub-menus: WARNING! Setting the wrong values in the sections below may cause the system to malfunction. Make sure that the settings made are compatible with the hardware.
PAGE 88
NANO-PV-D4252/N4552/D5252 EPIC SBC Aptio Setup Utility – Copyright (C) 2010 American Megatrends, Inc. Advanced ACPI Sleep State [S3 (Suspend to R…)] Set the ACPI state used for System suspend ---------------------: Select Screen  : Select Item Enter Select F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save ESC Exit Version 2.01.1204. Copyright (C) 2010 American Megatrends, Inc.
PAGE 89
NANO-PV-D4252/N4552/D5252 EPIC SBC Aptio Setup Utility – Copyright (C) 2010 American Megatrends, Inc. Advanced TPM Configuration TPM SUPPORT [Disable] Current TPM Status Information NO TPM Hardware Enables or Disables TPM support. O.S. will not show TPM. Reset of platform is required. ---------------------: Select Screen  : Select Item Enter Select F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save ESC Exit Version 2.02.1205. Copyright (C) 2010 American Megatrends, Inc.
PAGE 90
NANO-PV-D4252/N4552/D5252 EPIC SBC Aptio Setup Utility – Copyright (C) 2010 American Megatrends, Inc. Advanced CPU Configuration Processor Type EMT64 Processor Speed System Bus Speed Ratio Status Actual Ratio Processor Stepping Microcode Revision L1 Cache RAM L2 Cache RAM Processor Core Hyper-Threading Intel(R) Atom(TM) CPU CPU N475 @ 1.
PAGE 91
NANO-PV-D4252/N4552/D5252 EPIC SBC 5.3.4 SATA Configuration Use the SATA Configuration menu (BIOS Menu 6) to change and/or set the configuration of the SATA devices installed in the system. Aptio Setup Utility – Copyright (C) 2010 American Megatrends, Inc. Advanced PATA Master PATA Slave Not Present Not Present SATA SATA SATA SATA Not Not Not Not Port0 Port1 Port2 Port3 Present Present Present Present Select ATA/IDE Configuration.
PAGE 92
NANO-PV-D4252/N4552/D5252 EPIC SBC  Configure SATA as [IDE] Use the Configure SATA as option to configure SATA devices as normal IDE devices.  IDE  AHCI DEFAULT Configures SATA devices as normal IDE device. Configures SATA devices as AHCI device. 5.3.5 USB Configuration Use the USB Configuration menu (BIOS Menu 7) to read USB configuration information and configure the USB settings. Aptio Setup Utility – Copyright (C) 2010 American Megatrends, Inc.
PAGE 93
NANO-PV-D4252/N4552/D5252 EPIC SBC  Legacy USB Support [Enabled] Use the Legacy USB Support BIOS option to enable USB mouse and USB keyboard support. Normally if this option is not enabled, any attached USB mouse or USB keyboard does not become available until a USB compatible operating system is fully booted with all USB drivers loaded. When this option is enabled, any attached USB mouse or USB keyboard can control the system even when there is no USB driver loaded onto the system.
PAGE 94
NANO-PV-D4252/N4552/D5252 EPIC SBC 5.3.6.1 Serial Port n Configuration Use the Serial Port n Configuration menu (BIOS Menu 9) to configure the serial port n. Aptio Setup Utility – Copyright (C) 2010 American Megatrends, Inc. Advanced Serial Port 0 Configuration Serial Port Device Settings Enable or Disable Serial Port (COM) [Enabled] IO=3F8h; IRQ=4 --------------------: Select Screen  : Select Item Enter Select F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save ESC Exit Version 2.02.
PAGE 95
NANO-PV-D4252/N4552/D5252 EPIC SBC   IO=3F8h; Serial Port I/O port address is 3F8h and the interrupt IRQ=3, 4 address is IRQ3 and IRQ4 IO=2F8h; Serial Port I/O port address is 2F8h and the interrupt IRQ=3, 4 address is IRQ3 and IRQ4 5.3.6.1.2 Serial Port 1 Configuration  Serial Port [Enabled] Use the Serial Port option to enable or disable the serial port.
PAGE 96
NANO-PV-D4252/N4552/D5252 EPIC SBC   Enabled DEFAULT Enable the serial port Change Settings [Auto] Use the Change Settings option to change the serial port IO port address and interrupt address.  Auto DEFAULT The serial port IO port address and interrupt address are automatically detected.
PAGE 97
NANO-PV-D4252/N4552/D5252 EPIC SBC    IO=2E8h; Serial Port I/O port address is 2E8h and the interrupt IRQ=10 address is IRQ10 IO=3E8h; Serial Port I/O port address is 3E8h and the interrupt IRQ=10, 11 address is IRQ10, 11 IO=2E8h; Serial Port I/O port address is 2E8h and the interrupt IRQ=10, 11 address is IRQ10, 11 5.3.6.2 IrDA Configuration Use the IrDA Configuration menu (BIOS Menu 9) to configure the serial port n. Aptio Setup Utility – Copyright (C) 2010 American Megatrends, Inc.
PAGE 98
NANO-PV-D4252/N4552/D5252 EPIC SBC 5.3.6.3 Parallel Port Configuration Use the Parallel Port Configuration menu (BIOS Menu 9) to configure the serial port n. Aptio Setup Utility – Copyright (C) 2010 American Megatrends, Inc. Advanced Parallel Port Configuration Parallel Port Device Settings Change the Printer Port mode [Enabled] IO=378h; IRQ=7 --------------------: Select Screen  : Select Item Enter Select F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save ESC Exit Version 2.02.1205.
PAGE 99
NANO-PV-D4252/N4552/D5252 EPIC SBC   IO=3BCh; Parallel Port I/O port address is 3BCh and the IRQ=7 interrupt address is IRQ7  IO=378h Parallel Port I/O port address is 378h  IO=278h Parallel Port I/O port address is 278h  IO=3BCh Parallel Port I/O port address is 3BCh Device Mode [Printer Mode] Use the Device Mode option to select the mode the parallel port operates in. Configuration options are listed below.  Printer Mode  SPP Mode  EPP-1.9 and SPP Mode  EPP-1.
PAGE 100
NANO-PV-D4252/N4552/D5252 EPIC SBC Aptio Setup Utility – Copyright (C) 2010 American Megatrends, Inc. Advanced PC Health Status CPU Temperature SYS Temperature CPU FAN Speed VCC3V V_core Vcc Vcc12 V1_5VDDR VSB3V VBAT CPU Smart Fan control Temperature Bound1 Temperature Bound2 Temperature Bound3 Temperature Bound4 :+39 C :+40 C :4950 RPM :+3.344 V :+1.136 V :+5.087 V :+11.352 V :+1.504 V :+3.360 V :+3.
PAGE 101
NANO-PV-D4252/N4552/D5252 EPIC SBC  CPU Smart Fan control [Auto Mode] Use the CPU Smart Fan control option to configure the CPU fan.  Auto Mode The fan adjusts its speed using these settings: Temperature Bound 1 Temperature Bound 2 Temperature Bound 3 Temperature Bound 4  Manual Mode The fan spins at the speed set in: Manual Duty Cycle Setting 5.3.8 Serial Port Console Redirection The Serial Port Console Redirection menu (BIOS Menu 13) allows the console redirection options to be configured.
PAGE 102
NANO-PV-D4252/N4552/D5252 EPIC SBC  Disabled  Enabled DEFAULT Disabled the console redirection function Enabled the console redirection function 5.4 Chipset Use the Chipset menu (BIOS Menu 14) to access the Northbridge and Southbridge configuration menus WARNING! Setting the wrong values for the Chipset BIOS selections in the Chipset BIOS menu may cause the system to malfunction. Aptio Setup Utility – Copyright (C) 2010 American Megatrends, Inc.
PAGE 103
NANO-PV-D4252/N4552/D5252 EPIC SBC 5.4.1 Host Bridge Configuration Use the Host Bridge Configuration menu (BIOS Menu 15) to configure the Northbridge chipset. Aptio Setup Utility – Copyright (C) 2010 American Megatrends, Inc. Chipset > OnChip VGA Configuration Initate Graphic Adapter [IGD] Select which graphics controller to use as the primary boot device.
PAGE 104
NANO-PV-D4252/N4552/D5252 EPIC SBC 5.4.1.1 OnChip VGA Configuration Use the OnChip VGA Configuration menu (BIOS Menu 15) to configure the OnChip VGA. Aptio Setup Utility – Copyright (C) 2010 American Megatrends, Inc. Chipset OnChip VGA Configuration Select Share Memory Size. Share Memory Size Multi-Monitor Support [8 MB] [Enabled] --------------------: Select Screen  : Select Item Enter Select F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save ESC Exit Version 2.02.1205.
PAGE 105
NANO-PV-D4252/N4552/D5252 EPIC SBC  Disabled  Enabled Disabled the multi-monitor function Enabled the multi-monitor function DEFAULT 5.4.2 South Bridge Configuration Use the South Bridge Configuration menu (BIOS Menu 17) to configure the Southbridge chipset. Aptio Setup Utility – Copyright (C) 2010 American Megatrends, Inc. Chipset Auto Power Button Function HD Audio Controller USB Function USB 2.
PAGE 106
NANO-PV-D4252/N4552/D5252 EPIC SBC   Enabled DEFAULT USB function support enabled USB 2.0 (EHCI) Support [Enabled] Use the USB 2.0 (EHCI) Support BIOS option to enable or disable USB 2.0 support.   Enabled  Disabled DEFAULT USB 2.0 (EHCI) support enabled USB 2.0 (EHCI) support disabled Set Spread Spectrum Function [Disabled] The Set Spread Spectrum Function option can help to improve CPU EMI issues.
PAGE 107
NANO-PV-D4252/N4552/D5252 EPIC SBC  DVMT Mode Select [DVMT Mode] Use the DVMT Mode Select option to select the Intel Dynamic Video Memory Technology (DVMT) operating mode.   Fixed A fixed portion of graphics memory is reserved as Mode graphics memory. DVMT DEFAULT Mode  Graphics memory is dynamically allocated according to the system and graphics needs. DVMT/FIXED Memory [256 MB] Use the DVMT/FIXED Memory option to specify the maximum amount of memory that can be allocated as graphics memory.
PAGE 108
NANO-PV-D4252/N4552/D5252 EPIC SBC  1024x768 18bit  1280x1024 18bit  1366x768 18bit  1280x800 18bit  1280x600 18bit 5.5 Boot Use the Boot menu (BIOS Menu 19) to configure system boot options. Aptio Setup Utility – Copyright (C) 2010 American Megatrends, Inc.
PAGE 109
NANO-PV-D4252/N4552/D5252 EPIC SBC  Does not enable the keyboard Number Lock Off automatically. To use the 10-keys on the keyboard, press the Number Lock key located on the upper left-hand corner of the 10-key pad. The Number Lock LED on the keyboard lights up when the Number Lock is engaged.  Quiet Boot [Enabled] Use the Quiet Boot BIOS option to select the screen display when the system boots.
PAGE 110
NANO-PV-D4252/N4552/D5252 EPIC SBC Aptio Setup Utility – Copyright (C) 2010 American Megatrends, Inc. Main Advanced Chipset Boot Security Save & Exit Password Description Set Setup Administrator Password If ONLY the Administrator’s password is set, then this only limits access to Setup and is only asked for when entering Setup If ONLY the User’s password is set, then this is a power on password and must be entered to boot or enter Setup. In Setup the User will have Administrator rights.
PAGE 111
NANO-PV-D4252/N4552/D5252 EPIC SBC 5.7 Exit Use the Exit menu (BIOS Menu 21) to load default BIOS values, optimal failsafe values and to save configuration changes. Aptio Setup Utility – Copyright (C) 2010 American Megatrends, Inc. Main Advanced Chipset Boot Security Save & Exit Save Changes and Reset Discard Changes and Reset Exit system setup after saving the changes.
PAGE 112
NANO-PV-D4252/N4552/D5252 EPIC SBC  Save as User Defaults Use the Save as User Defaults option to save the changes done so far as user defaults.  Restore User Defaults Use the Restore User Defaults option to restore the user defaults to all the setup options.
PAGE 113
NANO-PV-D4252/N4552/D5252 EPIC SBC Appendix A A BIOS Menu Options BIOS Information .................................................................................................................72 System Date [xx/xx/xx] ........................................................................................................72 System Time [xx:xx:xx] .......................................................................................................73 ACPI Sleep State [S3 (Suspend to RAM)]..............
PAGE 114
NANO-PV-D4252/N4552/D5252 EPIC SBC Device Mode [Printer Mode]................................................................................................85 PC Health Status ..................................................................................................................86 CPU Smart Fan control [Auto Mode] .................................................................................87 Console Redirection [Disabled] .....................................................................
PAGE 115
NANO-PV-D4252/N4552/D5252 EPIC SBC Appendix B B One Key Recovery Page 101
PAGE 116
NANO-PV-D4252/N4552/D5252 EPIC SBC B.1 One Key Recovery Introduction The IEI one key recovery is an easy-to-use front end for the Norton Ghost system backup and recovery tool. The one key recovery provides quick and easy shortcuts for creating a backup and reverting to that backup or for reverting to the factory default settings. To create the system backup the main storage device must be split into two partitions (three partitions for Linux).
PAGE 117
NANO-PV-D4252/N4552/D5252 EPIC SBC o o o o  Windows 7 Windows CE 5.0 Windows CE 6.0 Windows XP Embedded Linux o o o o o o o o o o o o o o Fedora Core 12 (Constantine) Fedora Core 11 (Leonidas) Fedora Core 10 (Cambridge) Fedora Core 8 (Werewolf) Fedora Core 7 (Moonshine) RedHat RHEL-5.4 RedHat 9 (Ghirke) Ubuntu 8.10 (Intrepid) Ubuntu 7.10 (Gutsy) Ubuntu 6.10 (Edgy) Debian 5.0 (Lenny) Debian 4.0 (Etch) SuSe 11.2 SuSe 11.3 NOTE: Installing unsupported OS versions may cause the recovery tool to fail.
PAGE 118
NANO-PV-D4252/N4552/D5252 EPIC SBC NOTE: The recovery CD can only be used with IEI products. The software will fail to run and a warning message will appear when used on non-IEI hardware. B.2 Setup Procedure for Windows Prior to using the recovery tool to backup or restore system, a few setup procedures are required. Step 1: Hardware and BIOS setup Step 2: Create partitions Step 3: Install operating system, drivers and system applications.
PAGE 119
NANO-PV-D4252/N4552/D5252 EPIC SBC NOTE: The setup procedures described below are for Microsoft Windows operating system users. For Linux system, most setup procedures are the same with Microsoft Windows except for several steps which is described in Section B.3. B.2.1 Hardware and BIOS Setup Step 1: Make sure the system is powered off and unplugged. Step 2: Install a hard driver or SSD in the NANO-PV-D4252/N4552/D5252. An unformatted and unpartitioned disk is recommended.
PAGE 120
NANO-PV-D4252/N4552/D5252 EPIC SBC Figure B-1: Recovery Tool Setup Menu Step 5: Press <5> then . Figure B-2: Command Mode Step 6: The command prompt window appears. Type the following commands (marked in red) to create two partitions. One is for the OS installation; the other is for saving recovery files and images which will be an invisible partition.
PAGE 121
NANO-PV-D4252/N4552/D5252 EPIC SBC Figure B-3: Partition Creation Commands Page 107
PAGE 122
NANO-PV-D4252/N4552/D5252 EPIC SBC NOTE: Use the following commands to check if the partitions were created successfully. Step 7: Press any key to exit the recovery tool and automatically reboot the system. Please continue to the following procedure: Build-up Recovery Partition.Step0: B.2.3 Install Operating System, Drivers and Applications Install the operating system onto the unlabelled partition.
PAGE 123
NANO-PV-D4252/N4552/D5252 EPIC SBC Step 2: Start the system. Step 3: Press any key to boot from the recovery CD. It will take a while to launch the recovery tool. Please be patient. Step 4: When the recovery tool setup menu appears, press <2> then . Figure B-4: System Configuration for Windows Step 5: The Symantec Ghost window appears and starts configuring the system to build-up a recovery partition. In this process, the partition which is created for recovery files in Section B.2.
PAGE 124
NANO-PV-D4252/N4552/D5252 EPIC SBC Step 6: After completing the system configuration, press any key in the following window to reboot the system. Figure B-6: Press any key to continue Step 7: Eject the recovery CD.Step0: B.2.5 Create Factory Default Image NOTE: Before creating the factory default image, please configure the system to a factory default environment, including driver and application installations. To create a factory default image, please follow the steps below. Step 1: Turn on the system.
PAGE 125
NANO-PV-D4252/N4552/D5252 EPIC SBC Figure B-8: Recovery Tool Menu Step 3: The About Symantec Ghost window appears. Click OK button to continue. Figure B-9: About Symantec Ghost Window Step 4: Use mouse to navigate to the option shown below (Figure B-10).
PAGE 126
NANO-PV-D4252/N4552/D5252 EPIC SBC Figure B-10: Symantec Ghost Path Step 5: Select the local source drive as shown in Figure B-11. Then click OK. Figure B-11: Select a Local Source Drive Step 6: Select a source partition from basic drive as shown in Figure B-12. Then click OK.
PAGE 127
NANO-PV-D4252/N4552/D5252 EPIC SBC Step 7: Select 1.2: [Recovery] NTFS drive and enter a file name called iei (Figure B-13). Click Save. The factory default image will then be saved in the selected recovery drive and named IEI.GHO. WARNING: The file name of the factory default image must be iei.GHO.
PAGE 128
NANO-PV-D4252/N4552/D5252 EPIC SBC Step 8: When the Compress Image screen in Figure B-14 prompts, click High to make the image file smaller. Figure B-14: Compress Image Step 9: The Proceed with partition image creation window appears, click Yes to continue. Figure B-15: Image Creation Confirmation Step 10: The Symantec Ghost starts to create the factory default image (Figure B-16).
PAGE 129
NANO-PV-D4252/N4552/D5252 EPIC SBC Step 11: When the image creation completes, a screen prompts as shown in Figure B-17. Click Continue and close the Ghost window to exit the program. Figure B-17: Image Creation Complete Step 12: The recovery tool main menu window is shown as below. Press any key to reboot the system. Step0: Figure B-18: Press Any Key to Continue B.3 Setup Procedure for Linux The initial setup procedures for Linux system are mostly the same with the procedure for Microsoft Windows.
PAGE 130
NANO-PV-D4252/N4552/D5252 EPIC SBC NOTE: If the Linux OS is not installed with GRUB (v0.97 or earlier) and Ext3, the Symantec Ghost may not function properly. While installing Linux OS, please create two partitions:  Partition 1: /  Partition 2: SWAP NOTE: Please reserve enough space for partition 3 for saving recovery images. Figure B-19: Partitions for Linux Step 3: Create a recovery partition. Insert the recovery CD into the optical disk drive. Follow Step 1 ~ Step 3 described in Section B.2.2.
PAGE 131
NANO-PV-D4252/N4552/D5252 EPIC SBC system32>format N: /fs:ntfs /q /v:Recovery /y system32>exit Step 4: Build-up recovery partition. Press any key to boot from the recovery CD. It will take a while to launch the recovery tool. Please be patient. When the recovery tool setup menu appears, type <3> and press (Figure B-20). The Symantec Ghost window appears and starts configuring the system to build-up a recovery partition. After completing the system configuration, press any key to reboot the system.
PAGE 132
NANO-PV-D4252/N4552/D5252 EPIC SBC Step 7: The recovery tool menu appears. (Figure B-22) Figure B-22: Recovery Tool Menu Step 8: Create a factory default image. Follow Step 2 ~ Step 12 described in Section B.2.5 to create a factory default image. B.4 Recovery Tool Functions After completing the initial setup procedures as described above, users can access the recovery tool by pressing while booting up the system. The main menu of the recovery tool is shown below.
PAGE 133
NANO-PV-D4252/N4552/D5252 EPIC SBC Figure B-23: Recovery Tool Main Menu The recovery tool has several functions including: 1. Factory Restore: Restore the factory default image (iei.GHO) created in Section B.2.5. 2. Backup system: Create a system backup image (iei_user.GHO) which will be saved in the hidden partition. 3. Restore your last backup: Restore the last system backup image 4. Manual: Enter the Symantec Ghost window to configure manually. 5. Quit: Exit the recovery tool and restart the system.
PAGE 134
NANO-PV-D4252/N4552/D5252 EPIC SBC B.4.1 Factory Restore To restore the factory default image, please follow the steps below. Step 1: Type <1> and press in the main menu. Step 2: The Symantec Ghost window appears and starts to restore the factory default. A factory default image called iei.GHO is created in the hidden Recovery partition. Figure B-24: Restore Factory Default Step 3: The screen is shown as in Figure B-25 when completed. Press any key to reboot the system.
PAGE 135
NANO-PV-D4252/N4552/D5252 EPIC SBC B.4.2 Backup System To backup the system, please follow the steps below. Step 1: Type <2> and press in the main menu. Step 2: The Symantec Ghost window appears and starts to backup the system. A backup image called iei_user.GHO is created in the hidden Recovery partition. Figure B-26: Backup System Step 3: The screen is shown as in Figure B-27 when system backup is completed. Press any key to reboot the system.
PAGE 136
NANO-PV-D4252/N4552/D5252 EPIC SBC B.4.3 Restore Your Last Backup To restore the last system backup, please follow the steps below. Step 1: Type <3> and press in the main menu. Step 2: The Symantec Ghost window appears and starts to restore the last backup image (iei_user.GHO). Figure B-28: Restore Backup Step 3: The screen is shown as in Figure B-29 when backup recovery is completed. Press any key to reboot the system.
PAGE 137
NANO-PV-D4252/N4552/D5252 EPIC SBC B.4.4 Manual To restore the last system backup, please follow the steps below. Step 1: Type <4> and press in the main menu. Step 2: The Symantec Ghost window appears. Use the Ghost program to backup or recover the system manually. Figure B-30: Symantec Ghost Window Step 3: When backup or recovery is completed, press any key to reboot the system.
PAGE 138
NANO-PV-D4252/N4552/D5252 EPIC SBC Appendix C C Terminology Page 124
PAGE 139
NANO-PV-D4252/N4552/D5252 EPIC SBC AC ’97 Audio Codec 97 (AC’97) refers to a codec standard developed by Intel® in 1997. ACPI Advanced Configuration and Power Interface (ACPI) is an OS-directed configuration, power management, and thermal management interface. AHCI Advanced Host Controller Interface (AHCI) is a SATA Host controller register-level interface. ATA The Advanced Technology Attachment (ATA) interface connects storage devices including hard disks and CD-ROM drives to a computer.
PAGE 140
NANO-PV-D4252/N4552/D5252 EPIC SBC memory. DIMM Dual Inline Memory Modules are a type of RAM that offer a 64-bit data bus and have separate electrical contacts on each side of the module. EHCI The Enhanced Host Controller Interface (EHCI) specification is a register-level interface description for USB 2.0 Host Controllers. GbE Gigabit Ethernet (GbE) is an Ethernet version that transfers data at 1.0 Gbps and complies with the IEEE 802.3-2005 standard.
PAGE 141
NANO-PV-D4252/N4552/D5252 EPIC SBC SATA Serial ATA (SATA) is a serial communications bus designed for data transfers between storage devices and the computer chipsets. The SATA bus has transfer speeds up to 1.5 Gbps and the SATA 3Gb/s bus has data transfer speeds of up to 3.0 Gbps. S.M.A.R.T Self Monitoring Analysis and Reporting Technology (S.M.A.R.T) refers to automatic status checking technology implemented on hard disk drives.
PAGE 142
NANO-PV-D4252/N4552/D5252 EPIC SBC Appendix D D Watchdog Timer Page 128
PAGE 143
NANO-PV-D4252/N4552/D5252 EPIC SBC NOTE: The following discussion applies to DOS environment. IEI support is contacted or the IEI website visited for specific drivers for more sophisticated operating systems, e.g., Windows and Linux. The Watchdog Timer is provided to ensure that standalone systems can always recover from catastrophic conditions that cause the CPU to crash. This condition may have occurred by external EMI or a software bug.
PAGE 144
NANO-PV-D4252/N4552/D5252 EPIC SBC NOTE: When exiting a program it is necessary to disable the Watchdog Timer, otherwise the system resets.
PAGE 145
NANO-PV-D4252/N4552/D5252 EPIC SBC Appendix E E Hazardous Materials Disclosure Page 131
PAGE 146
NANO-PV-D4252/N4552/D5252 EPIC SBC E.1 Hazardous Material Disclosure Table for IPB Products Certified as RoHS Compliant Under 2002/95/EC Without Mercury The details provided in this appendix are to ensure that the product is compliant with the Peoples Republic of China (China) RoHS standards. The table below acknowledges the presences of small quantities of certain materials in the product, and is applicable to China RoHS only.
PAGE 147
NANO-PV-D4252/N4552/D5252 EPIC SBC Part Name Toxic or Hazardous Substances and Elements Lead Mercury Cadmium Hexavalent Polybrominated Polybrominated (Pb) (Hg) (Cd) Chromium Biphenyls Diphenyl Ethers (CR(VI)) (PBB) (PBDE) Housing X O O O O X Display X O O O O X Printed Circuit Board X O O O O X Metal Fasteners X O O O O O Cable Assembly X O O O O X Fan Assembly X O O O O X Power Supply Assemblies X O O O O X Battery O O O O O O O: This
PAGE 148
NANO-PV-D4252/N4552/D5252 EPIC SBC 此附件旨在确保本产品符合中国 RoHS 标准。以下表格标示此产品中某有毒物质的含量符合中国 RoHS 标准规定的限量要求。本产品上会附有”环境友好使用期限”的标签，此期限是估算这些物质”不会有泄漏或突变”的年限。本产品可能包含有较短的环境友好使用期限的可替换元件，像是电池或灯管，这些元件将会单独标示出来。部件名称有毒有害物质或元素铅汞镉六价铬多溴联苯多溴二苯醚 (Pb) (Hg) (Cd) (CR(VI)) (PBB) (PBDE) 壳体 X O O O O X 显示 X O O O O X 印刷电路板 X O O O O X 金属螺帽 X O O O O O 电缆组装 X O O O O X 风扇组装 X O O O O X 电力供应组装 X O O O O X 电池 O O O O O O O: 表示该有毒有害物质在该部件所有物质材料中的含量均在 SJ/T11363-2006 标准规定的限