User Manual

ManualsBrandsIEI Integration ManualsHardwareNANO-QM770

NANO-QM770 EPIC SBC

Page i

User Manual

NANO-QM770

MODEL:

EPIC SBC with 3rd Generation 22nm Intel

Mobile CPU

Up to 8.0 GB DDR3, DVI, HDMI, LVDS, Dual GbE,

SATA 6Gb/s, USB 3.0, PCIe Mini, Intel® AMT, RoHS

Rev. 1.01 – 26 November, 2013

Summary of content (190 pages)

PAGE 1
NANO-QM770 EPIC SBC MODEL: NANO-QM770 EPIC SBC with 3rd Generation 22nm Intel® Mobile CPU Up to 8.0 GB DDR3, DVI, HDMI, LVDS, Dual GbE, SATA 6Gb/s, USB 3.0, PCIe Mini, Intel® AMT, RoHS User Manual Page i Rev. 1.
PAGE 2
NANO-QM770 EPIC SBC Revision Date Version Changes 26 November, 2013 1.01 Updated Appendix D.2: DIO Connector Pinouts 24 May, 2012 1.
PAGE 3
NANO-QM770 EPIC SBC Copyright COPYRIGHT NOTICE The information in this document is subject to change without prior notice in order to improve reliability, design and function and does not represent a commitment on the part of the manufacturer. In no event will the manufacturer be liable for direct, indirect, special, incidental, or consequential damages arising out of the use or inability to use the product or documentation, even if advised of the possibility of such damages.
PAGE 4
NANO-QM770 EPIC SBC Table of Contents 1 INTRODUCTION.......................................................................................................... 1 1.1 INTRODUCTION........................................................................................................... 2 1.2 BENEFITS ................................................................................................................... 2 1.3 FEATURES ................................................................................
PAGE 5
NANO-QM770 EPIC SBC 3.2.11 Power Connector (12V) ................................................................................. 27 3.2.12 RS-232 Serial Port Connectors (COM1, COM2) .......................................... 28 3.2.13 RS-422/485 Serial Port Connector (COM3).................................................. 28 3.2.14 SATA Drive Connectors ................................................................................. 29 3.2.15 SATA Power Connectors .......................................
PAGE 6
NANO-QM770 EPIC SBC 4.7.3 SATA Drive Connection ................................................................................... 54 4.7.4 Single RS-232 Cable (w/o Bracket) ................................................................. 55 4.8 EXTERNAL PERIPHERAL INTERFACE CONNECTION ................................................... 56 4.8.1 DVI Display Device Connection...................................................................... 56 4.8.2 HDMI Display Device Connection ......................
PAGE 7
NANO-QM770 EPIC SBC 5.4.2 System Agent (SA) Configuration .................................................................... 86 5.4.2.1 Graphics Configuration............................................................................. 87 5.4.2.2 Memory Configuration ............................................................................. 90 5.5 BOOT........................................................................................................................ 91 5.6 SECURITY ................
PAGE 8
NANO-QM770 EPIC SBC B.5.4 Manual........................................................................................................... 153 B.6 RESTORE SYSTEMS FROM A LINUX SERVER THROUGH LAN .................................. 154 B.6.1 Configure DHCP Server Settings .................................................................. 155 B.6.2 Configure TFTP Settings ............................................................................... 156 B.6.3 Configure One Key Recovery Server Settings ......
PAGE 9
NANO-QM770 EPIC SBC List of Figures Figure 1-1: NANO-QM770...............................................................................................................2 Figure 1-2: Connectors (Front)......................................................................................................3 Figure 1-3: Connectors (Solder Side) ...........................................................................................4 Figure 1-4: Dimensions (mm) ................................................
PAGE 10
NANO-QM770 EPIC SBC Figure 3-26: HDMI Connector ......................................................................................................38 Figure 4-1: SO-DIMM Installation ................................................................................................43 Figure 4-2: PCIe Mini Card Installation.......................................................................................44 Figure 4-3: AT/ATX Mode Selection Jumper Location.................................................
PAGE 11
NANO-QM770 EPIC SBC Figure 6-17: LAN Driver Installation ........................................................................................ 108 Figure 6-18: LAN Driver Installation Complete....................................................................... 108 Figure 6-19: InstallShield Wizard Welcome Screen ............................................................... 109 Figure 6-20: Audio Driver Software Configuration.................................................................
PAGE 12
NANO-QM770 EPIC SBC Figure B-17: Compress Image.................................................................................................. 138 Figure B-18: Image Creation Confirmation ............................................................................. 139 Figure B-19: Image Creation Complete ................................................................................... 139 Figure B-20: Image Creation Complete .............................................................................
PAGE 13
NANO-QM770 EPIC SBC List of Tables Table 1-1: Technical Specifications..............................................................................................8 Table 2-1: Packing List.................................................................................................................12 Table 2-2: Optional Items.............................................................................................................13 Table 3-1: Peripheral Interface Connectors ..........................
PAGE 14
NANO-QM770 EPIC SBC Table 4-1: Jumpers .......................................................................................................................45 Table 4-2: AT/ATX Mode Selection Jumper Settings ................................................................45 Table 4-3: Clear CMOS Jumper Settings....................................................................................47 Table 4-4: Clear ME RTC Registers Jumper Settings .............................................................
PAGE 15
NANO-QM770 EPIC SBC BIOS Menus BIOS Menu 1: Main .......................................................................................................................65 BIOS Menu 2: Advanced ..............................................................................................................66 BIOS Menu 3: ACPI Configuration ..............................................................................................67 BIOS Menu 4: RTC Wake Settings .............................................
PAGE 16
NANO-QM770 EPIC SBC Chapter 1 1 Introduction Page 1
PAGE 17
NANO-QM770 EPIC SBC 1.1 Introduction Figure 1-1: NANO-QM770 The NANO-QM770 is an EPIC SBC with a 3rd generation 22nm Intel® mobile CPU and Intel® QM77 Express Chipset. Storage on the board is handled by the SATA 6Gb/s ports for connecting a hard drive, optical drive or SSD. The PCIe Mini slot allows an mSATA card to be installed. The board has three types of graphics outputs. A DVI-I output connects to a DVI monitor or a traditional VGA monitor.
PAGE 18
NANO-QM770 EPIC SBC EPIC form factor RoHS compliant Intel® AMT 8.0 support Dual GbE Supports HDMI, LVDS and DVI-I interface for triple independent display (HDMI V1.3a compliant) Six USB ports (two USB 2.0, four USB 3.0) Three serial ports PCIe Mini card slot 1.4 Connectors The connectors on the NANO-QM770 are shown in the figure below.
PAGE 19
NANO-QM770 EPIC SBC Figure 1-3: Connectors (Solder Side) Page 4
PAGE 20
NANO-QM770 EPIC SBC 1.5 Dimensions The main dimensions of the NANO-QM770 are shown in the diagram below.
PAGE 21
NANO-QM770 EPIC SBC 1.6 Data Flow Figure 1-5 shows the data flow between the system chipset, the CPU and other components installed on the motherboard.
PAGE 22
NANO-QM770 EPIC SBC 1.7 Technical Specifications NANO-QM770 technical specifications are listed in Table 1-1. Specification NANO-QM770 Form Factor EPIC CPU Socket Socket G2 CPU 3rd generation 22nm Intel® mobile CPU System Chipset Intel® QM77 Memory One 204-pin 1600/1333/1066 MHz DDR3 SO-DIMM supported (system max. 8GB) Graphics Engine Intel® Gen 7 with DirectX 11, OGL 3.1, OCL 1.
PAGE 23
NANO-QM770 EPIC SBC USB Ports Two USB 2.0 (via pin header) Four external USB 3.0 ports One 4-pin wafer connector SMBus Storage Two independent SATA channels with 6Gb/s data transfer rates SATA Environmental and Power Specifications Power Supply 12V only, AT/ATX support Power Connector 1 x Internal 4-pin (2x2) power connector Power Consumption 12V@5.87A (2.
PAGE 24
NANO-QM770 EPIC SBC Chapter 2 2 Packing List Page 9
PAGE 25
NANO-QM770 EPIC SBC 2.1 Anti-static Precautions WARNING! Static electricity can destroy certain electronics. Make sure to follow the ESD precautions to prevent damage to the product, and injury to the user. Make sure to adhere to the following guidelines: Wear an anti-static wristband: - Wearing an anti-static wristband can prevent electrostatic discharge. Self-grounding:- Touch a grounded conductor every few minutes to discharge any excess static buildup.
PAGE 26
NANO-QM770 EPIC SBC 2.3 Packing List NOTE: If any of the components listed in the checklist below are missing, do not proceed with the installation. Contact the IEI reseller or vendor the NANO-QM770 was purchased from or contact an IEI sales representative directly by sending an email to sales@iei.com.tw.
PAGE 27
NANO-QM770 EPIC SBC Quantity Item and Part Number 1 Utility CD 1 One Key Recovery CD 1 Quick installation guide Image Table 2-1: Packing List 2.4 Optional Items These optional items are available.
PAGE 28
NANO-QM770 EPIC SBC Item and Part Number Image Infineon TPM module (P/N: TPM-IN01-R11) Table 2-2: Optional Items Page 13
PAGE 29
NANO-QM770 EPIC SBC Chapter 3 3 Connector Pinouts Page 14
PAGE 30
NANO-QM770 EPIC SBC 3.1 Peripheral Interface Connectors Section 3.1.1 shows peripheral interface connector locations. Section 3.1.2 lists all the peripheral interface connectors seen in Section 3.1.1. 3.1.1 Layout The figure below shows the on-board peripheral connectors, rear panel peripheral connectors and on-board jumpers.
PAGE 31
NANO-QM770 EPIC SBC Figure 3-2: Connector and Jumper Locations (Solder Side) 3.1.2 Peripheral Interface Connectors The table below shows a list of the peripheral interface connectors on the NANO-QM770. Detailed descriptions of these connectors can be found below.
PAGE 32
NANO-QM770 EPIC SBC Connector Type Label PCIe Mini card slot PCIe Mini card slot CN4 Power connector (12V) 4-pin connector PWR1 RS-232 serial ports (COM1, COM2) 10-pin header COM1, COM2 RS-422/485 serial port (COM3) 4-pin wafer COM3 SATA connectors SATA connector S_ATA1, S_ATA2 SATA power connectors 2-pin wafer CN1, CN2 SMBus connector 4-pin wafer CN3 SO-DIMM connector SO-DIMM connector DIMM1 SPI Flash 6-pin wafer JSPI1 TPM connector 20-pin header TPM1 USB 2.
PAGE 33
NANO-QM770 EPIC SBC 3.2 Internal Peripheral Connectors Internal peripheral connectors are found on the motherboard and are only accessible when the motherboard is outside of the chassis. This section has complete descriptions of all the internal, peripheral connectors on the NANO-QM770. 3.2.1 Audio Connector CN Label: AUDIO1 CN Type: 10-pin header CN Location: See Figure 3-3 CN Pinouts: See Table 3-3 This connector connects to speaker, microphone and audio input connectors on the front panel.
PAGE 34
NANO-QM770 EPIC SBC 3.2.2 Battery Connector CAUTION: Risk of explosion if battery is replaced by an incorrect type. Only certified engineers should replace the on-board battery. Dispose of used batteries according to instructions and local regulations. CN Label: BAT1 CN Type: 2-pin wafer CN Location: See Figure 3-4 CN Pinouts: See Table 3-4 This is connected to the system battery. The battery provides power to the system clock to retain the time when power is turned off.
PAGE 35
NANO-QM770 EPIC SBC 3.2.3 Digital I/O Connector CN Label: DIO1 CN Type: 10-pin header CN Location: See Figure 3-5 CN Pinouts: See Table 3-5 The digital I/O connector provides programmable input and output for external devices. The digital I/O provides 4-bit output and 4-bit input.
PAGE 36
NANO-QM770 EPIC SBC The fan connector attaches to a CPU cooling fan. Figure 3-6: CPU Fan Connector Location Pin Description 1 GND 2 +V12S 3 Rotation Signal 4 PWM Control Signal Table 3-6: CPU Fan Connector Pinouts 3.2.5 Fan Connector (System) CN Label: SYS_FAN1 CN Type: 3-pin wafer CN Location: See Figure 3-7 CN Pinouts: See Table 3-7 The fan connector attaches to a system cooling fan.
PAGE 37
NANO-QM770 EPIC SBC Pin Description 1 Rotation Signal 2 +12V 3 GND Table 3-7: System Fan Connector Pinouts 3.2.6 Front Panel Connector CN Label: F_PANEL1 CN Type: 10-pin header CN Location: See Figure 3-8 CN Pinouts: See Table 3-8 The front panel connector connects to the indicator LEDs and buttons on the computer's front panel.
PAGE 38
NANO-QM770 EPIC SBC 3.2.7 Keyboard/Mouse Connector CN Label: KB_MS1 CN Type: 6-pin wafer CN Location: See Figure 3-9 CN Pinouts: See Table 3-9 The keyboard/mouse connector connects to a PS/2 Y-cable that can be connected to a PS/2 keyboard and mouse. Figure 3-9: Keyboard/Mouse Connector Location Pin Description 1 VCC5_KBMS 2 Mouse Data 3 Mouse Clock 4 Keyboard Data 5 Keyboard Clock 6 GND Table 3-9: Keyboard/Mouse Connector Pinouts 3.2.
PAGE 39
NANO-QM770 EPIC SBC CN Pinouts: See Table 3-10 The LVDS connector is for an LCD panel connected to the board.
PAGE 40
NANO-QM770 EPIC SBC 3.2.9 LVDS Backlight Connector CN Label: INVERTER1 CN Type: 5-pin wafer CN Location: See Figure 3-11 CN Pinouts: See Table 3-11 The backlight inverter connectors provide power to LCD panels. Figure 3-11: LVDS Backlight Inverter Connector Pin Description 1 BRIGHTNESS 2 GROUND 3 +12VS_LCD_BKL 4 GROUND 5 BACKLIGHT ENABLE Table 3-11: Backlight Inverter Connector Pinouts 3.2.
PAGE 41
NANO-QM770 EPIC SBC The PCIe Mini card slot enables a PCIe Mini card expansion module to be connected to the board. Cards supported include among others wireless LAN (WLAN) cards and IEI PCIe Mini disk on module (DOM) SSD cards. Figure 3-12: PCIe Mini Card Slot Location Pin Description Pin Description 1 PCIE_WAKE# 2 VCC3 3 N/C 4 GND 5 N/C 6 1.
PAGE 42
NANO-QM770 EPIC SBC Pin Description Pin Description 41 N/C 42 N/C 43 N/C 44 N/C 45 N/C 46 N/C 47 N/C 48 1.5V 49 N/C 50 GND 51 N/C 52 VCC3 Table 3-12: PCIe Mini Card Slot Pinouts 3.2.11 Power Connector (12V) CN Label: PWR1 CN Type: 4-pin connector CN Location: See Figure 3-13 CN Pinouts: See Table 3-13 The power connector is connected to an external power supply and supports 12V power input. Power is provided to the system, from the power supply through this connector.
PAGE 43
NANO-QM770 EPIC SBC 3.2.12 RS-232 Serial Port Connectors (COM1, COM2) CN Label: COM1, COM2 CN Type: 10-pin header CN Location: See Figure 3-14 CN Pinouts: See Table 3-14 The 10-pin serial port connectors provide two RS-232 serial communications channels. The COM serial port connectors can be connected to external RS-232 serial port devices.
PAGE 44
NANO-QM770 EPIC SBC CN Pinouts: See Table 3-15 This connector provides RS-422 or RS-485 communications. Figure 3-15: RS-422/485 Serial Port Connector Location Pin Description 1 RXD485# 2 RXD485+ 3 TXD485+ 4 TXD485# Table 3-15: RS-422/485 Serial Port Connector Pinouts Use the optional RS-422/485 cable to connect to a serial device. The pinouts of the DB-9 connector are listed below. RS-422 Pinouts RS-485 Pinouts Table 3-16: DB-9 RS-422/485 Pinouts 3.2.
PAGE 45
NANO-QM770 EPIC SBC CN Location: See Figure 3-16 CN Pinouts: See Table 3-17 The SATA connectors connect to SATA hard drives or optical drives with data transfer speeds as high as 6Gb/s. Figure 3-16: SATA Drive Connector Locations Pin Description 1 GND 2 TX+ 3 TX- 4 GND 5 RX- 6 RX+ 7 GND Table 3-17: SATA Drive Connector Pinouts 3.2.
PAGE 46
NANO-QM770 EPIC SBC Figure 3-17: SATA Power Connector Locations Pin Description 1 +V5S 2 GND Table 3-18: SATA Power Connector Pinouts 3.2.16 SMBus Connector CN Label: CN3 CN Type: 4-pin wafer CN Location: See Figure 3-18 CN Pinouts: See Table 3-19 The SMBus (System Management Bus) connector provides low-speed system management communications.
PAGE 47
NANO-QM770 EPIC SBC Pin Description 1 GND 2 SMB_DATA 3 SMB_CLK 4 +V5S Table 3-19: SMBus Connector Pinouts 3.2.17 SO-DIMM Connector CN Label: DIMM1 CN Type: 204-pin DDR3 SO-DIMM connector CN Location: See Figure 3-19 The SO-DIMM connector is for installing memory on the system. Figure 3-19: SO-DIMM Connector Location 3.2.
PAGE 48
NANO-QM770 EPIC SBC Figure 3-20: SPI Flash Connector Location Pin Description 1 +V3.3M_SPI_CON 2 SPI_CS 3 SPI_SO_SW 4 SPI_CLK_SW 5 SPI_SI_SW 6 GND Table 3-20: SPI Flash Connector Pinouts 3.2.19 TPM Connector CN Label: TPM1 CN Type: 20-pin header CN Location: See Figure 3-21 CN Pinouts: See Table 3-21 The Trusted Platform Module (TPM) connector secures the system on bootup.
PAGE 49
NANO-QM770 EPIC SBC Figure 3-21: TPM Connector Location Pin Description Pin Description 1 LCLK 2 GND 3 LFRAME# 4 KEY 5 LRERST# 6 +5V 7 LAD3 8 LAD2 9 +3V 10 LAD1 11 LAD0 12 GND 13 SCL 14 SDA 15 SB3V 16 SERIRQ 17 GND 18 GLKRUN# 19 LPCPD# 20 LDRQ# Table 3-21: TPM Connector Pinouts 3.2.20 USB 2.0 Connector CN Label: USB1 CN Type: 8-pin header CN Location: See Figure 3-22 CN Pinouts: See Table 3-22 The USB header can connect to two USB devices.
PAGE 50
NANO-QM770 EPIC SBC Figure 3-22: USB Connector Location Pin Description Pin Description 1 VCC 2 GND 3 DATA- 4 DATA+ 5 DATA+ 6 DATA- 7 GND 8 VCC Table 3-22: USB Port Connector Pinouts 3.3 External Interface Connectors Figure 3-23 shows the NANO-QM770 motherboard external interface connectors. The NANO-QM770 on-board external interface connectors are shown in Figure 3-23. Figure 3-23: External Interface Connectors 3.3.
PAGE 51
NANO-QM770 EPIC SBC CN Location: See Figure 3-23 CN Pinouts: See Table 3-23 and Figure 3-24 The 24-pin Digital Visual Interface (DVI) connector connects to high-speed, high-resolution digital displays. The DVI-I connector supports both digital and analog signals.
PAGE 52
NANO-QM770 EPIC SBC CN Pinouts: See Table 3-24 The LAN connector connects to a local network. PIN DESCRIPTION PIN DESCRIPTION 1 MDIA3- 5 MDIA1+ 2 MDIA3+ 6 MDIA2+- 3 MDIA2- 7 MDIA0- 4 MDIA1- 8 MDIA0+ Table 3-24: LAN Pinouts Figure 3-25: Ethernet Connector LED Description LED Description A on: linked B off: 10 Mb/s blinking: data is being sent/received green: 100 Mb/s orange: 1000 Mb/s Table 3-25: Connector LEDs 3.3.
PAGE 53
NANO-QM770 EPIC SBC Pin Description Pin Description 1 HDMI_DATA2 13 N/C 2 GND 14 N/C 3 HDMI_DATA2# 15 HDMI_SCL 4 HDMI_DATA1 16 HDMI_SDA 5 GND 17 GND 6 HDMI_DATA1# 18 +5V 7 HDMI_DATA0 19 HDMI_HPD 8 GND 20 HDMI_GND 9 HDMI_DATA0# 21 HDMI_GND 10 HDMI_CLK 22 HDMI_GND 11 GND 23 HDMI_GND 12 HDMI_CLK# Table 3-26: HDMI Connector Pinouts Figure 3-26: HDMI Connector 3.3.4 USB 3.0 Connectors CN Label: USB_CON1, USB_CON2 CN Type: USB 3.
PAGE 54
NANO-QM770 EPIC SBC Pin Description Pin Description 1 VBUS 2 DATA1- 3 DATA1+ 4 GND 5 SSRX1- 6 SSRX1+ 7 GND 8 SSTX1- 9 SSTX1+ 10 VBUS 11 DATA2- 12 DATA2+ 13 GND 14 SSRX2- 15 SSRX2+ 16 GND 17 SSTX2- 18 SSTX2+ Table 3-27: USB Port Pinouts Page 39
PAGE 55
NANO-QM770 EPIC SBC Chapter 4 4 Installation Page 40
PAGE 56
NANO-QM770 EPIC SBC 4.1 Anti-static Precautions WARNING: Failure to take ESD precautions during installation may result in permanent damage to the product and severe injury to the user. Electrostatic discharge (ESD) can cause serious damage to electronic components, including the NANO-QM770. Dry climates are especially susceptible to ESD. It is therefore critical to strictly adhere to the following anti-static precautions whenever the NANO-QM770, or any other electrical component, is handled.
PAGE 57
NANO-QM770 EPIC SBC WARNING: The installation instructions described in this manual should be carefully followed in order to prevent damage to the NANO-QM770, NANO-QM770 components and injury to the user. Before and during the installation please DO the following: Read the user manual: o The user manual provides a complete description of the installation instructions and configuration options. Wear an electrostatic discharge cuff (ESD): o Electronic components are easily damaged by ESD.
PAGE 58
NANO-QM770 EPIC SBC 4.3 SO-DIMM Installation To install an SO-DIMM, please follow the steps below and refer to Figure 4-1. Figure 4-1: SO-DIMM Installation Step 1: Locate the SO-DIMM socket. Place the board on an anti-static mat. Step 2: Align the SO-DIMM with the socket. Align the notch on the memory with the notch on the memory socket. Step 3: Insert the SO-DIMM. Push the memory in at a 20º angle. (See Figure 4-1) Step 4: Seat the SO-DIMM. Gently push downwards and the arms clip into place.
PAGE 59
NANO-QM770 EPIC SBC Figure 4-2: PCIe Mini Card Installation Step 1: Insert into the socket at an angle. Line up the notch on the card with the notch on the connector. Slide the PCIe Mini card into the socket at an angle of about 20º. Step 2: Push down until the card clips into place. Push the other end of the card down until it clips into place on the plastic connector.Step 0: 4.5 Jumper Settings NOTE: A jumper is a metal bridge that is used to close an electrical circuit.
PAGE 60
NANO-QM770 EPIC SBC Before the NANO-QM770 is installed in the system, the jumpers must be set in accordance with the desired configuration. The jumpers on the NANO-QM770 are listed in Table 4-1.
PAGE 61
NANO-QM770 EPIC SBC Figure 4-3: AT/ATX Mode Selection Jumper Location 4.5.2 Clear CMOS Jumper Label: J_CMOS1 Jumper Type: 3-pin header Jumper Settings: See Table 4-3 Jumper Location: See Figure 4-4 If the NANO-QM770 fails to boot due to improper BIOS settings, the clear CMOS jumper clears the CMOS data and resets the system BIOS information. To do this, use the jumper cap to close pins 2 and 3 for a few seconds then reinstall the jumper clip back to pins 1 and 2.
PAGE 62
NANO-QM770 EPIC SBC Pin Description Short 1-2 Keep CMOS Setup (Default) Short 2-3 Clear CMOS Setup Table 4-3: Clear CMOS Jumper Settings Figure 4-4: Clear CMOS Jumper Location 4.5.3 Clear ME RTC Registers Jumper Label: ME_RTC1 Jumper Type: 3-pin header Jumper Settings: See Table 4-4 Jumper Location: See Figure 4-5 Resets the RTC registers used for the Intel® Management Engine when the on-board battery is changed.
PAGE 63
NANO-QM770 EPIC SBC Figure 4-5: Clear ME RTC Registers Jumper Location 4.5.4 Flash Descriptor Security Override Jumper Label: J_FLASH1 Jumper Type: 3-pin header Jumper Settings: See Table 4-5 Jumper Location: See Figure 4-6 The Flash Descriptor Security Override jumper specifies whether to override the flash descriptor.
PAGE 64
NANO-QM770 EPIC SBC 4.5.5 LVDS Voltage Selection Jumper Label: J_VLVDS1 Jumper Type: 3-pin header Jumper Settings: See Table 4-6 Jumper Location: See Figure 4-7 Selects the voltage of the LVDS connector. Pin Description Short 1-2 +3.3 V (Default) Short 2-3 +5 V Table 4-6: LVDS Voltage Selection Jumper Settings Figure 4-7: LVDS Voltage Selection Jumper Location 4.5.
PAGE 65
NANO-QM770 EPIC SBC Pin Description 3-4 1024 X 768 (18bit) 1-2 & 3-4 1024 X 768 (24bit) 5-6 1280 X 800 (24bit) 1-2 & 5-6 1280 X 1024 (48bit) 3-4 & 5-6 1366 X 768 (24bit) 1-2 & 3-4 & 5-6 1440 X 900 (48bit) 7-8 1400 X 1050 (48bit) 1-2 & 7-8 1600 X 900 (48bit) 3-4 & 7-8 1600 X 1200 (48bit) 1-2 & 3-4 & 7-8 1680 X 1050 (48bit) 5-6 & 7-8 1920 X 1080 (48bit) 1-2 & 5-6 & 7-8 1920 X 1200 (48bit) 3-4 & 5-6 & 7-8 2048 X 1536 (48bit) 1-2 & 3-4 & 5-6 & 7-8 LVDS disabled Default Table 4-7:
PAGE 66
NANO-QM770 EPIC SBC Pin Description Closed PCIe Mini (Default) Open mSATA Table 4-8: PCIe Mini/mSATA Mode Selection Jumper Settings Figure 4-9: PCIe Mini/mSATA Mode Selection Jumper Location 4.6 Chassis Installation 4.6.1 Airflow WARNING: Airflow is critical for keeping components within recommended operating termperatures. The chassis should have fans and vents as necessary to keep things cool.
PAGE 67
NANO-QM770 EPIC SBC 4.7 Internal Peripheral Device Connections This section outlines the installation of peripheral devices to the onboard connectors. 4.7.1 AT Power Connection Follow the instructions below to connect the NANO-QM770 to an AT power supply. WARNING: Disconnect the power supply power cord from its AC power source to prevent a sudden power surge to the NANO-QM770. Step 1: Locate the power cable. The power cable is shown in the packing list in Chapter 2.
PAGE 68
NANO-QM770 EPIC SBC Step 3: Connect Power Cable to Power Supply. Connect one of the 4-pin (1x4) Molex type power cable connectors to an AT power supply. See Figure 4-11. Figure 4-11: Connect Power Cable to Power Supply 4.7.2 Audio Kit Installation The Audio Kit that came with the NANO-QM770 connects to the audio connector on the NANO-QM770. The audio kit consists of three audio jacks. Mic-in connects to a microphone. Line-in provides a stereo line-level input to connect to the output of an audio device.
PAGE 69
NANO-QM770 EPIC SBC Figure 4-12: Audio Kit Cable Connection Step 3: Connect the audio devices. Connect speakers to the line-out audio jack. Connect the output of an audio device to the line-in audio jack. Connect a microphone to the mic-in audio jack.Step 0: 4.7.3 SATA Drive Connection The NANO-QM770 is shipped with two SATA drive cable. To connect the SATA drive to the connector, please follow the steps below. Step 1: Locate the SATA connector and the SATA power connector.
PAGE 70
NANO-QM770 EPIC SBC Figure 4-13: SATA Drive Cable Connection Step 3: Connect the cable to the SATA disk. Connect the connector on the other end of the cable to the connector at the back of the SATA drive. See Figure 4-13. Step 4: To remove the SATA cable from the SATA connector, press the clip on the connector at the end of the cable. Step 0: 4.7.
PAGE 71
NANO-QM770 EPIC SBC Figure 4-14: Single RS-232 Cable Installation Step 3: Secure the bracket. The single RS-232 connector has two retention screws that must be secured to a chassis or bracket. Step 4: Connect the serial device. Once the single RS-232 connector is connected to a chassis or bracket, a serial communications device can be connected to the system. Step 0: 4.8 External Peripheral Interface Connection Devices can be connected to the external connectors.
PAGE 72
NANO-QM770 EPIC SBC Step 2: Align the DVI-I connector. Align the male DVI-I connector on the digital display device cable with the female DVI-I connector on the external peripheral interface. Step 3: Insert the DVI-I connector. Once the connectors are properly aligned with the male connector, insert the male connector from the digital display device into the female connector on the NANO-QM770. See Figure 4-15. Figure 4-15: DVI Connector Step 4: Secure the connector.
PAGE 73
NANO-QM770 EPIC SBC Step 2: Align the connector. Align the HDMI connector with the HDMI port. Make sure the orientation of the connector is correct. Figure 4-16: HDMI Connection Step 3: Insert the HDMI connector. Gently insert the HDMI connector. The connector should engage with a gentle push. If the connector does not insert easily, check again that the connector is aligned correctly, and that the connector is being inserted with the right way up. Step 0: 4.8.
PAGE 74
NANO-QM770 EPIC SBC Figure 4-17: LAN Connection Step 3: Insert the LAN cable RJ-45 connector. Once aligned, gently insert the LAN cable RJ-45 connector into the on-board RJ-45 connector. Step 0: 4.8.4 USB Connection The external USB 3.0 connectors provide easier and quicker access to external USB devices. Follow the steps below to connect USB devices to the NANO-QM770. Step 1: Locate the USB 3.0 connectors. The locations of the USB 3.0 connectors are shown in Chapter 3. Step 2: Insert a USB 3.0 plug.
PAGE 75
NANO-QM770 EPIC SBC Figure 4-18: USB Connector 4.9 Intel® AMT Setup Procedure The NANO-QM770 is featured with the Intel® Active Management Technology (AMT). To enable the Intel® AMT function, follow the steps below. Step 1: Make sure the DIMM1 socket is installed with one DDR3 SO-DIMM. Step 2: Connect an Ethernet cable to the RJ-45 connector labeled LAN1.
PAGE 76
NANO-QM770 EPIC SBC NOTE: To change the password, enter a new password following the strong password rule (containing at least one upper case letter, one lower case letter, one digit and one special character, and be at least eight characters).
PAGE 77
NANO-QM770 EPIC SBC Chapter 5 5 BIOS Page 62
PAGE 78
NANO-QM770 EPIC SBC 5.1 Introduction The BIOS is programmed onto the BIOS chip. The BIOS setup program allows changes to certain system settings. This chapter outlines the options that can be changed. 5.1.1 Starting Setup The UEFI BIOS is activated when the computer is turned on. The setup program can be activated in one of two ways. 1. Press the DELETE or F2 key as soon as the system is turned on or 2. Press the DELETE or F2 key when the “Press Del to enter SETUP” message appears on the screen. 0.
PAGE 79
NANO-QM770 EPIC SBC Key Function Esc Main Menu – Quit and do not save changes into CMOS Status Page Setup Menu and Option Page Setup Menu -Exit current page and return to Main Menu F1 General help, only for Status Page Setup Menu and Option Page Setup Menu F9 Load optimized defaults F10 Save changes and Exit BIOS Table 5-1: BIOS Navigation Keys 5.1.
PAGE 80
NANO-QM770 EPIC SBC 5.2 Main The Main BIOS menu (BIOS Menu 1) appears when the BIOS Setup program is entered. The Main menu gives an overview of the basic system information. Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc. Main Advanced Chipset Boot Security Save & Exit BIOS Information BIOS Vendor Core Version Compliency Project Version Build Date American Megatrends 4.6.5.3 0.18 UEFI 2.3; PI 1.2 B208AR01.ROM 05/10/2012 10:09:44 Set the Date. Use Tab to switch between Date elements.
PAGE 81
NANO-QM770 EPIC SBC Î System Time [xx:xx:xx] Use the System Time option to set the system time. Manually enter the hours, minutes and seconds. 5.3 Advanced Use the Advanced menu (BIOS Menu 2) to configure the CPU and peripheral devices through the following sub-menus: WARNING! Setting the wrong values in the sections below may cause the system to malfunction. Make sure that the settings made are compatible with the hardware. Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc.
PAGE 82
NANO-QM770 EPIC SBC 5.3.1 ACPI Configuration The ACPI Configuration menu (BIOS Menu 3) configures the Advanced Configuration and Power Interface (ACPI) options. Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc. Advanced ACPI Settings ACPI Sleep State [S1 only (CPU Stop C…] Select ACPI sleep state the system will enter when the SUSPEND button is pressed.
PAGE 83
NANO-QM770 EPIC SBC 5.3.2 RTC Wake Settings The RTC Wake Settings menu (BIOS Menu 4) configures RTC wake event. Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc. Advanced Wake system with Fixed Time [Disabled] Enable or disable System wake on alarm event. When enabled, System will wake on the dat::hr::min::sec specified ---------------------ÅÆ: Select Screen ↑ ↓: Select Item Enter Select F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save ESC Exit Version 2.14.1219.
PAGE 84
NANO-QM770 EPIC SBC Î Enabled If selected, the following appears with values that can be selected: *Wake up every day *Wake up date *Wake up hour *Wake up minute *Wake up second After setting the alarm, the computer turns itself on from a suspend state when the alarm goes off. 5.3.3 Trusted Computing Use the Trusted Computing menu (BIOS Menu 5) to configure settings related to the Trusted Computing Group (TCG) Trusted Platform Module (TPM).
PAGE 85
NANO-QM770 EPIC SBC Î Security Device Support [Disable] Use the Security Device Support option to configure support for the TPM. Î Disable DEFAULT TPM support is disabled. Î Enable TPM support is enabled. 5.3.4 CPU Configuration Use the CPU Configuration menu (BIOS Menu 6) to view detailed CPU specifications and configure the CPU. Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc. Advanced CPU Configuration Intel(R) Core(TM) i7-3610QE CPU @ 2.
PAGE 86
NANO-QM770 EPIC SBC Max CPU Speed: Lists the maximum CPU processing speed. Min CPU Speed: Lists the minimum CPU processing speed. CPU Speed: Lists the CPU processing speed Processor Core: Lists the number of the processor cores Intel HT Technology: Indicates if Intel HT Technology is supported by the CPU. Intel VT-x Technology: Indicates if Intel VT-x Technology is supported by the CPU. Intel SMX Technology: Indicates if Intel SMX Technology is supported by the CPU.
PAGE 87
NANO-QM770 EPIC SBC 5.3.5 SATA Configuration Use the SATA Configuration menu (BIOS Menu 7) to change and/or set the configuration of the SATA devices installed in the system. Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc. Advanced SATA Mode Selection [AHCI] Serial ATA Software Hot Plug Serial ATA Software Hot Plug Empty Unknown [Disabled] Empty Unknown [Disabled] Port0 Preserve Port1 Preserve Determines how SATA controller(s) operate.
PAGE 88
NANO-QM770 EPIC SBC 5.3.6 Intel(R) Rapid Start Technology Use the Intel(R) Rapid Start Technology menu to configure Intel® Rapid Start Technology support. Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc. Advanced Intel(R) Rapid Start Technology [Disabled] --------------------ÅÆ: Select Screen ↑ ↓: Select Item Enter Select + - Change Opt. F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save & Exit ESC Exit Version 2.14.1219. Copyright (C) 2011 American Megatrends, Inc.
PAGE 89
NANO-QM770 EPIC SBC Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc. Advanced Intel Trusted Execution Technology Configuration Intel TXT support only can be enabled/disabled if SMX is enabled. VT and VT-d support must also be enabled prior to TXT. Secure Mode Extensons (SMX) Disabled Intel TXT(LT) Support [Disabled] --------------------ÅÆ: Select Screen ↑ ↓: Select Item Enter Select + - Change Opt.
PAGE 90
NANO-QM770 EPIC SBC Î Intel AMT [Enabled] Use Intel AMT option to enable or disable the Intel® AMT function. Î Î Disabled Î Enabled Intel® AMT is disabled DEFAULT Intel® AMT is enabled Unconfigure ME [Disabled] Use the Unconfigure ME option to perform ME unconfigure without password operation. Î Disabled Î Enabled DEFAULT Not perform ME unconfigure To perform ME unconfigure 5.3.
PAGE 91
NANO-QM770 EPIC SBC Î USB Devices The USB Devices Enabled field lists the USB devices that are enabled on the system Î Legacy USB Support [Enabled] Use the Legacy USB Support BIOS option to enable USB mouse and USB keyboard support. Normally if this option is not enabled, any attached USB mouse or USB keyboard does not become available until a USB compatible operating system is fully booted with all USB drivers loaded.
PAGE 92
NANO-QM770 EPIC SBC 5.3.10.1 Serial Port n Configuration Use the Serial Port n Configuration menu (BIOS Menu 13) to configure the serial port n. Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc. Advanced Serial Port 1 Configuration Serial Port Device Settings Enable or Disable Serial Port (COM) [Enabled] IO=3F8h; IRQ=4 --------------------ÅÆ: Select Screen ↑ ↓: Select Item Enter Select F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save ESC Exit Version 2.14.1219.
PAGE 93
NANO-QM770 EPIC SBC Î Î Î Î IO=3F8h; Serial Port I/O port address is 3E8h and the interrupt IRQ=3, 4 address is IRQ3, 4 IO=2F8h; Serial Port I/O port address is 2F8h and the interrupt IRQ=3, 4 address is IRQ3, 4 IO=3E8h; Serial Port I/O port address is 3E8h and the interrupt IRQ=3, 4 address is IRQ3, 4 IO=2E8h; Serial Port I/O port address is 2E8h and the interrupt IRQ=3, 4 address is IRQ3, 4 5.3.10.1.
PAGE 94
NANO-QM770 EPIC SBC Î IO=2E8h; Serial Port I/O port address is 2E8h and the interrupt IRQ=3, 4 address is IRQ3, 4 5.3.10.1.3 Serial Port 3 Configuration Î Serial Port [Enabled] Use the Serial Port option to enable or disable the serial port. Î Î Disabled Î Enabled Disable the serial port DEFAULT Enable the serial port Change Settings [Auto] Use the Change Settings option to change the serial port IO port address and interrupt address.
PAGE 95
NANO-QM770 EPIC SBC 5.3.11 F81866 H/W Monitor The F8186 H/W Monitor menu (BIOS Menu 14) shows the operating temperature, fan speeds and system voltages. Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc. Advanced PC Health Status Smart Fan Mode Select CPU temperature :+62 C Accuracy: 1. -5~ +10 degree around 100 degree. 2. -10~ +15 degree around 50 degree. System temperature :+37 C CPU Fan Speed :2325 RPM SYS Fan Speed :N/A +5VS :+5.171 V +V12S :+12.056 V +V1.5 :+1.632 V VSB5V :+5.
PAGE 96
NANO-QM770 EPIC SBC o o o o VSB5V VCC3V VSB3V VBAT 5.3.11.1 Smart Fan Mode Configuration Use the Smart Fan Mode Configuration submenu (BIOS Menu 15) to configure the smart fan temperature and speed settings. Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc.
PAGE 97
NANO-QM770 EPIC SBC Î SYS_FAN1 Smart Fan Control [Auto Duty-Cycle Mode] Use the SYS_FAN1 Smart Fan Control option to configure the System Smart Fan (SYS_FAN1). Î Î Î Manual Duty The fan spins at the speed set in Manual by Duty Mode Cycle settings Auto Duty-Cycle The fan adjusts its speed using Auto by Mode Duty-Cycle settings Temperature n Use the + or – key to change the fan Temperature n value. Enter a decimal number between 0 and 85. 5.3.
PAGE 98
NANO-QM770 EPIC SBC Î Console Redirection [Disabled] Use Console Redirection option to enable or disable the console redirection function. Î Disabled Î Enabled DEFAULT Disabled the console redirection function Enabled the console redirection function 5.3.13 IEI Feature Use the IEI Feature menu (BIOS Menu 17) to configure One Key Recovery function. Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc.
PAGE 99
NANO-QM770 EPIC SBC 5.4 Chipset Use the Chipset menu (BIOS Menu 18) to access the Hostbridge and Southbridge configuration menus. WARNING! Setting the wrong values for the Chipset BIOS selections in the Chipset BIOS menu may cause the system to malfunction. Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc.
PAGE 100
NANO-QM770 EPIC SBC 5.4.1 PCH-IO Configuration Use the PCH-IO Configuration menu (BIOS Menu 19) to configure the PCH chipset. Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc. Chipset PCH-IO Configuration Intel PCH RC Version Intel PCH SKU Name Intel PCH Rev ID 1.1.0.0 QM77 04/C1 Auto Power Button Status [Disabled] Azalia Azalia Internal HDMI Codec [Auto] [Enabled] Restore AC Power Loss [Last State] Control Detection of the Azalia device.
PAGE 101
NANO-QM770 EPIC SBC Î Disabled Î Enabled Î Disable internal HDMI codec for High Definition Audio DEFAULT Enable internal HDMI codec for High Definition Audio Restore AC Power Loss [Last State] Use the Restore AC Power Loss BIOS option to specify what state the system returns to if there is a sudden loss of power to the system. Î Power Off The system remains turned off Î Power On The system turns on Î Last State DEFAULT The system returns to its previous state. If it was on, it turns itself on.
PAGE 102
NANO-QM770 EPIC SBC Aptio Setup Utility – Copyright (C) 2010 American Megatrends, Inc. Chipset System Agent Bridge Name System Agent RC Version VT-d Capability IvyBridge 1.1.0.0 Supported VT-d > Graphics Configuration > Memory Configuration [Enabled] Enabled to reduce power consumption in system off state. --------------------ÅÆ: Select Screen ↑ ↓: Select Item Enter Select F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save ESC Exit Version 2.14.1219.
PAGE 103
NANO-QM770 EPIC SBC Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc. Chipset Graphics Configuration IGFX VBIOS Version Igfx Frequency 2132 350 MHz Primary Display PEG0 – Gen X [IGFX] [Gen1] DVMT Pre-Allocated DVMT Total Gfx Mem [128M] [MAX] Select which of IGFX/PEG/PCI Graphics device should be Primary Display Or select SG for Switchable Gfx.
PAGE 104
NANO-QM770 EPIC SBC then only be used as graphics memory, and is no longer available to applications or the operating system. Configuration options are listed below: Î 32M 64M 96M 128M 256M 512M 1024M Default DVMT Total Gfx Mem [MAX] Use the DVMT Total Gfx Mem option to select DVMT5.0 total graphic memory size used by the internal graphic device.
PAGE 105
NANO-QM770 EPIC SBC Î 800x600 18BIT 1024x768 18BIT 1024x768 24BIT 1280x800 24BIT 1280x1024 48BIT 1366x768 24BIT 1440x900 48BIT 1400x1050 48BIT 1600x900 48BIT 1600x1200 48BIT 1680x1050 48BIT 1920x1080 48BIT 1920x1200 48BIT 2048x1536 48BIT Backlight Control [Inverted] Use the Backlight Control option to select the backlight control mode. Î Inverted Î Normal DEFAULT The LVDS backlight is brighter at high voltage level.
PAGE 106
NANO-QM770 EPIC SBC Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc. Chipset Memory Information Memory RC Version 1.1.0.0 Memory Frequency 1333 MHz Total Memory 2048 MB (DDR3) DIMM#0 2048 MB (DDR3) CAS Latency (tCL) 9 Minimum delay time CAS to RAS (tRCDmin) 9 Row Precharge (tRPmin) 9 Active to Precharge (tRASmin) 24 XMP Profile 1 Not Supported XMP Profile 2 Not Supported --------------------ÅÆ: Select Screen ↑ ↓: Select Item Enter Select +/-: Change Opt.
PAGE 107
NANO-QM770 EPIC SBC Î Bootup NumLock State [On] Use the Bootup NumLock State BIOS option to specify if the number lock setting must be modified during boot up. Î On DEFAULT Allows the Number Lock on the keyboard to be enabled automatically when the computer system boots up. This allows the immediate use of the 10-key numeric keypad located on the right side of the keyboard. To confirm this, the Number Lock LED light on the keyboard is lit.
PAGE 108
NANO-QM770 EPIC SBC Î Option ROM Messages [Force BIOS] Use the Option ROM Messages option to set the Option ROM display mode. Î Force DEFAULT Sets display mode to force BIOS. BIOS Î Sets display mode to current. Keep Current Î Launch PXE OpROM [Disabled] Use the Launch PXE OpROM option to enable or disable boot option for legacy network devices. Î Î Disabled Î Enabled DEFAULT Ignore all PXE Option ROMs Load PXE Option ROMs.
PAGE 109
NANO-QM770 EPIC SBC 5.6 Security Use the Security menu (BIOS Menu 24) to set system and user passwords. Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc. Main Advanced Chipset Boot Security Save & Exit Password Description If ONLY the Administrator’s password is set, then this only limits access to Setup and is only asked for when entering Setup If ONLY the User’s password is set, then this is a power on password and must be entered to boot or enter Setup.
PAGE 110
NANO-QM770 EPIC SBC Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc. Main Advanced Chipset Boot Security Save & Exit Save Changes and Reset Discard Changes and Reset Reset the system after saving the changes. Restore Defaults Save as User Defaults Restore User Defaults --------------------ÅÆ: Select Screen ↑ ↓: Select Item Enter Select F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save ESC Exit Version 2.14.1219. Copyright (C) 2011 American Megatrends, Inc.
PAGE 111
NANO-QM770 EPIC SBC Chapter 6 6 Software Drivers Page 96
PAGE 112
NANO-QM770 EPIC SBC 6.1 Available Software Drivers NOTE: The content of the CD may vary throughout the life cycle of the product and is subject to change without prior notice. Visit the IEI website or contact technical support for the latest updates. The following drivers can be installed on the system: Chipset Graphics LAN Audio SATA (Intel® Rapid Storage Technology) USB 3.0 Intel® AMT Installation instructions are given below. 6.
PAGE 113
NANO-QM770 EPIC SBC Figure 6-1: Introduction Screen Step 3: Click NANO-QM770. Step 4: A new screen with a list of available drivers appears (Figure 6-2). Figure 6-2: Available Drivers Step 5: Install all of the necessary drivers in this menu.
PAGE 114
NANO-QM770 EPIC SBC 6.3 Chipset Driver Installation To install the chipset driver, please do the following. Step 1: Access the driver list. (See Section 6.2) Step 2: Click “Chipset”. Step 3: Locate the setup file and double click on it. Step 4: The Welcome Screen in Figure 6-3 appears. Step 5: Click Next to continue. Figure 6-3: Chipset Driver Welcome Screen Step 6: The license agreement in Figure 6-4 appears. Step 7: Read the License Agreement. Step 8: Click Yes to continue.
PAGE 115
NANO-QM770 EPIC SBC Figure 6-4: Chipset Driver License Agreement Step 9: The Read Me file in Figure 6-5 appears. Step 10: Click Next to continue.
PAGE 116
NANO-QM770 EPIC SBC Step 11: Setup Operations are performed as shown in Figure 6-6. Step 12: Once the Setup Operations are complete, click Next to continue. Figure 6-6: Chipset Driver Setup Operations Step 13: The Finish screen in Figure 6-7 appears. Step 14: Select “Yes, I want to restart this computer now” and click Finish.
PAGE 117
NANO-QM770 EPIC SBC Figure 6-7: Chipset Driver Installation Finish Screen 6.4 Graphics Driver Installation To install the Graphics driver, please do the following. Step 1: Access the driver list. (See Section 6.2) Step 2: Click “Graphics” and select the folder which corresponds to the operating system. Step 3: Double click the setup file. Step 4: The Welcome Screen in Figure 6-8 appears. Step 5: Click Next to continue.
PAGE 118
NANO-QM770 EPIC SBC Figure 6-8: Graphics Driver Welcome Screen Step 6: The License Agreement in Figure 6-9 appears. Step 7: Click Yes to accept the agreement and continue. Figure 6-9: Graphics Driver License Agreement Step 8: Setup Operations are performed as shown in Figure 6-10.
PAGE 119
NANO-QM770 EPIC SBC Step 9: Once the Setup Operations are complete, click Next to continue. Figure 6-10: Graphics Driver Setup Operations Step 10: The Finish screen in Figure 6-11 appears. Step 11: Select “Yes, I want to restart this computer now” and click Finish.
PAGE 120
NANO-QM770 EPIC SBC 6.5 LAN Driver Installation Step 1: Right-click the Computer button from the start menu and select Properties. (Figure 6-12). Figure 6-12: Windows Control Panel Step 2: The system control panel window in Figure 6-13 appears. Step 3: Click the Device Manager link (Figure 6-13).
PAGE 121
NANO-QM770 EPIC SBC Step 4: A list of system hardware devices appears (Figure 6-14). Step 5: Right-click the Ethernet Controller that has question marks next to it (this means Windows does not recognize the device). Step 6: Select Update Driver Software. Figure 6-14: Device Manager List Step 7: The Update Driver Software Window appears (Figure 6-15).
PAGE 122
NANO-QM770 EPIC SBC Figure 6-15: Update Driver Software Window Step 8: Select “Browse my computer for driver software” and click NEXT to continue. Step 9: Click Browse to select “X:\3-LAN” directory in the Locate File window, where “X:\” is the system CD drive. (Figure 6-16). Figure 6-16: Locate Driver Files Step 10: Click NEXT to continue. Step 11: Driver Installation is performed as shown in Figure 6-17.
PAGE 123
NANO-QM770 EPIC SBC Figure 6-17: LAN Driver Installation Step 12: The Finish screen in Figure 6-18 appears. Click Close to exit. Step 0: Figure 6-18: LAN Driver Installation Complete 6.6 Audio Driver Installation To install the audio driver, please do the following. Step 1: Access the driver list. (See Section 6.
PAGE 124
NANO-QM770 EPIC SBC Step 2: Click “Audio” and select the folder which corresponds to the operating system. Step 3: Double click the setup file. Step 4: The InstallShield Wizard is prepared to guide the user through the rest of the process. Step 5: Once initialized, the InstallShield Wizard welcome screen appears (Figure 6-19). Figure 6-19: InstallShield Wizard Welcome Screen Step 6: Click NEXT to continue the installation. Step 7: InstallShield starts to install the new software as shown in Figure 6-20.
PAGE 125
NANO-QM770 EPIC SBC Figure 6-20: Audio Driver Software Configuration Step 8: After the driver installation process is complete, a confirmation screen appears (Figure 6-21).
PAGE 126
NANO-QM770 EPIC SBC Step 9: The confirmation screen offers the option of restarting the computer now or later. For the settings to take effect, the computer must be restarted. Click FINISH to restart the computer. Step 0: 6.7 Intel® Rapid Storage Technology Driver Installation To install the Intel® Rapid Storage Technology driver, please do the following. Step 1: Access the driver list. (See Section 6.2) Step 2: Click “SATA”. Step 3: Locate the setup file and double click on it.
PAGE 127
NANO-QM770 EPIC SBC Figure 6-23: SATA RAID Driver License Agreement Step 9: The Read Me file in Figure 6-24 appears. Step 10: Click Next to continue. Figure 6-24: SATA RAID Driver Read Me File Step 11: Setup Operations are performed as shown in Figure 6-25. Step 12: Once the Setup Operations are complete, click Next to continue.
PAGE 128
NANO-QM770 EPIC SBC Figure 6-25: SATA RAID Driver Setup Operations Step 13: The Finish screen in Figure 6-26 appears. Step 14: Select “Yes, I want to restart this computer now” and click Finish.
PAGE 129
NANO-QM770 EPIC SBC 6.8 USB 3.0 Driver Installation WARNING: Do not run this driver’s installer (Setup.exe) from a USB storage device (ie. external USB hard drive or USB thumb drive). For proper installation, please copy driver files to a local hard drive folder and run from there. To install the touch panel software driver, please follow the steps below. Step 1: Access the driver list. (See Section 6.2) Step 2: Click “USB 3.0”. Step 3: Locate the setup file and double click on it.
PAGE 130
NANO-QM770 EPIC SBC Step 7: Read the License Agreement. Step 8: Click Yes to continue. Figure 6-28: USB 3.0 Driver License Agreement Step 9: The Read Me file in Figure 6-29 appears. Step 10: Click Next to continue. Figure 6-29: USB 3.
PAGE 131
NANO-QM770 EPIC SBC Step 11: Setup Operations are performed as shown in Figure 6-30. Step 12: Once the Setup Operations are complete, click Next to continue. Figure 6-30: USB 3.0 Driver Setup Operations Step 13: The Finish screen in Figure 6-31 appears. Step 14: Select “Yes, I want to restart this computer now” and click Finish.Step 0: Figure 6-31: USB 3.
PAGE 132
NANO-QM770 EPIC SBC 6.
PAGE 133
NANO-QM770 EPIC SBC Figure 6-32: Intel® ME Driver Welcome Screen Step 6: The license agreement in Figure 6-33 appears. Step 7: Read the License Agreement. Step 8: Click Yes to continue. Figure 6-33: Intel® ME Driver License Agreement Step 9: Setup Operations are performed as shown in Figure 6-34. Step 10: Once the Setup Operations are complete, click Next to continue.
PAGE 134
NANO-QM770 EPIC SBC Figure 6-34: Intel® ME Driver Setup Operations Step 11: The Finish screen in Figure 6-35 appears. Step 12: Select “Yes, I want to restart this computer now” and click Finish.
PAGE 135
NANO-QM770 EPIC SBC Appendix A A BIOS Options Page 120
PAGE 136
NANO-QM770 EPIC SBC Below is a list of BIOS configuration options in the BIOS chapter. BIOS Information .................................................................................................................65 System Date [xx/xx/xx] ........................................................................................................65 System Time [xx:xx:xx] .......................................................................................................
PAGE 137
NANO-QM770 EPIC SBC PEG0 – Gen X [Gen1]...........................................................................................................88 DVMT Pre-Allocated [128MB]..............................................................................................88 DVMT Total Gfx Mem [MAX]................................................................................................89 Primary IGFX Boot Display [VBIOS Default] .....................................................................
PAGE 138
NANO-QM770 EPIC SBC Appendix B B One Key Recovery Page 123
PAGE 139
NANO-QM770 EPIC SBC B.1 One Key Recovery Introduction The IEI one key recovery is an easy-to-use front end for the Norton Ghost system backup and recovery tool. This tool provides quick and easy shortcuts for creating a backup and reverting to that backup or reverting to the factory default settings.
PAGE 140
NANO-QM770 EPIC SBC After completing the five initial setup procedures as described above, users can access the recovery tool by pressing while booting up the system. The detailed information of each function is described in Section B.5. NOTE: The initial setup procedures for Linux system are described in Section B.3. B.1.1 System Requirement NOTE: The recovery CD can only be used with IEI products. The software will fail to run and a warning message will appear when used on non-IEI hardware.
PAGE 141
NANO-QM770 EPIC SBC partitions. Please take the following table as a reference when calculating the size of the partition. OS OS Image after Ghost Compression Ratio Windows® 7 7 GB 5 GB 70% Windows® XPE 776 MB 560 MB 70% Windows® CE 6.0 36 MB 28 MB 77% NOTE: Specialized tools are required to change the partition size if the operating system is already installed. B.1.2 Supported Operating System The recovery CD is compatible with both Microsoft Windows and Linux operating systems (OS).
PAGE 142
NANO-QM770 EPIC SBC Linux o o o o o o o o o o o o o o Fedora Core 12 (Constantine) Fedora Core 11 (Leonidas) Fedora Core 10 (Cambridge) Fedora Core 8 (Werewolf) Fedora Core 7 (Moonshine) RedHat RHEL-5.4 RedHat 9 (Ghirke) Ubuntu 8.10 (Intrepid) Ubuntu 7.10 (Gutsy) Ubuntu 6.10 (Edgy) Debian 5.0 (Lenny) Debian 4.0 (Etch) SuSe 11.2 SuSe 10.3 NOTE: Installing unsupported OS versions may cause the recovery tool to fail. B.
PAGE 143
NANO-QM770 EPIC SBC The detailed descriptions are described in the following sections. NOTE: The setup procedures described below are for Microsoft Windows operating system users. For Linux, most of the setup procedures are the same except for several steps described in Section B.3. B.2.1 Hardware and BIOS Setup Step 1: Make sure the system is powered off and unplugged. Step 2: Install a hard drive or SSD in the system. An unformatted and unpartitioned disk is recommended.
PAGE 144
NANO-QM770 EPIC SBC Step 2: Boot the system from recovery CD. When prompted, press any key to boot from the recovery CD. It will take a while to launch the recovery tool. Please be patient! Figure B-2: Launching the Recovery Tool Step 3: The recovery tool setup menu is shown as below. Figure B-3: Recovery Tool Setup Menu Step 4: Press <6> then .
PAGE 145
NANO-QM770 EPIC SBC Figure B-4: Command Prompt Step 5: The command prompt window appears. Type the following commands (marked in red) to create two partitions. One is for the OS installation; the other is for saving recovery files and images which will be an invisible partition.
PAGE 146
NANO-QM770 EPIC SBC Figure B-5: Partition Creation Commands Page 131
PAGE 147
NANO-QM770 EPIC SBC NOTE: Use the following commands to check if the partitions were created successfully. Step 6: Press any key to exit the recovery tool and automatically reboot the system. Please continue to the following procedure: Build the Recovery Partition.Step0: B.2.3 Install Operating System, Drivers and Applications Install the operating system onto the unlabelled partition.
PAGE 148
NANO-QM770 EPIC SBC B.2.4 Building the Recovery Partition Step 1: Put the recover CD in the optical drive. Step 2: Start the system. Step 3: Boot the system from the recovery CD. When prompted, press any key to boot from the recovery CD. It will take a while to launch the recovery tool. Please be patient! Figure B-6: Launching the Recovery Tool Step 4: When the recovery tool setup menu appears, press <2> then .
PAGE 149
NANO-QM770 EPIC SBC Step 5: The Symantec Ghost window appears and starts configuring the system to build a recovery partition. In this process the partition created for recovery files in Section B.2.2 is hidden and the recovery tool is saved in this partition. Figure B-8: Building the Recovery Partition Step 6: After completing the system configuration, press any key in the following window to reboot the system. Figure B-9: Press Any Key to Continue Step 7: Eject the recovery CD.
PAGE 150
NANO-QM770 EPIC SBC B.2.5 Create Factory Default Image NOTE: Before creating the factory default image, please configure the system to a factory default environment, including driver and application installations. To create a factory default image, please follow the steps below. Step 1: Turn on the system. When the following screen displays (Figure B-10), press the key to access the recovery tool.
PAGE 151
NANO-QM770 EPIC SBC Figure B-12: About Symantec Ghost Window Step 4: Use mouse to navigate to the option shown below (Figure B-13). Figure B-13: Symantec Ghost Path Step 5: Select the local source drive (Drive 1) as shown in Figure B-14. Then click OK.
PAGE 152
NANO-QM770 EPIC SBC Figure B-14: Select a Local Source Drive Step 6: Select a source partition (Part 1) from basic drive as shown in Figure B-15. Then click OK. Figure B-15: Select a Source Partition from Basic Drive Step 7: Select 1.2: [Recovery] NTFS drive and enter a file name called iei (Figure B-16). Click Save. The factory default image will then be saved in the selected recovery drive and named IEI.GHO. WARNING: The file name of the factory default image must be iei.GHO.
PAGE 153
NANO-QM770 EPIC SBC Figure B-16: File Name to Copy Image to Step 8: When the Compress Image screen in Figure B-17 prompts, click High to make the image file smaller.
PAGE 154
NANO-QM770 EPIC SBC Step 9: The Proceed with partition image creation window appears, click Yes to continue. Figure B-18: Image Creation Confirmation Step 10: The Symantec Ghost starts to create the factory default image (Figure B-19). Figure B-19: Image Creation Complete Step 11: When the image creation completes, a screen prompts as shown in Figure B-20. Click Continue and close the Ghost window to exit the program.
PAGE 155
NANO-QM770 EPIC SBC Step 12: The recovery tool main menu window is shown as below. Press any key to reboot the system. Step0: Figure B-21: Press Any Key to Continue B.3 Auto Recovery Setup Procedure The auto recovery function allows a system to automatically restore from the factory default image after encountering a Blue Screen of Death (BSoD) or a hang for around 10 minutes. To use the auto recovery function, follow the steps described in the following sections.
PAGE 156
NANO-QM770 EPIC SBC Step 1: Follow the steps described in Section B.2.1 ~ Section B.2.3 to setup BIOS, create partitions and install operating system. Step 2: Install the auto recovery utility into the system by double clicking the Utility/AUTORECOVERY-SETUP.exe in the One Key Recovery CD. This utility MUST be installed in the system, otherwise, the system will automatically restore from the factory default image every ten (10) minutes.
PAGE 157
NANO-QM770 EPIC SBC Step 4: Reboot the system from the recovery CD. When prompted, press any key to boot from the recovery CD. It will take a while to launch the recovery tool. Please be patient! Figure B-24: Launching the Recovery Tool Step 5: When the recovery tool setup menu appears, press <4> then . Figure B-25: Auto Recovery Environment for Windows Step 6: The Symantec Ghost window appears and starts configuring the system to build an auto recovery partition.
PAGE 158
NANO-QM770 EPIC SBC Figure B-26: Building the Auto Recovery Partition Step 7: After completing the system configuration, the following message prompts to confirm whether to create a factory default image. Type Y to have the system create a factory default image automatically. Type N within 6 seconds to skip this process (The default option is YES). It is suggested to choose YES for this option.
PAGE 159
NANO-QM770 EPIC SBC Step 8: The Symantec Ghost starts to create the factory default image (Figure B-28). Figure B-28: Image Creation Complete Step 9: After completing the system configuration, press any key in the following window to restart the system. Figure B-29: Press any key to continue Step 10: Eject the One Key Recovery CD and restart the system. Step 11: Press the key as soon as the system is turned on to enter the BIOS.
PAGE 160
NANO-QM770 EPIC SBC Main Advanced PCIPNP BIOS SETUP UTILITY Boot Security Chipset Exit iEi Feature ⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯ Auto Recovery Function [Enabled] Recover from PXE [Disabled] ÅÆ ↑ ↓ Enter F1 F10 ESC Select Screen Select Item Go to SubScreen General Help Save and Exit Exit v02.61 ©Copyright 1985-2006, American Megatrends, Inc. Figure B-30: IEI Feature Step 13: Save changes and restart the system.
PAGE 161
NANO-QM770 EPIC SBC Partition 1: / Partition 2: SWAP NOTE: Please reserve enough space for partition 3 for saving recovery images. Figure B-31: Partitions for Linux Step 3: Create a recovery partition. Insert the recovery CD into the optical disk drive. Follow Step 1 ~ Step 3 described in Section B.2.2. Then type the following commands (marked in red) to create a partition for recovery images.
PAGE 162
NANO-QM770 EPIC SBC recovery partition. After completing the system configuration, press any key to reboot the system. Eject the recovery CD. Figure B-32: Manual Recovery Environment for Linux Step 5: Access the recovery tool main menu by modifying the “menu.lst”. To first access the recovery tool main menu, the menu.lst must be modified. In Linux, enter Administrator (root). When prompt appears, type: cd /boot/grub vi menu.lst Figure B-33: Access menu.lst in Linux (Text Mode) Step 6: Modify the menu.
PAGE 163
NANO-QM770 EPIC SBC Step 7: The recovery tool menu appears. (Figure B-34) Figure B-34: Recovery Tool Menu Step 8: Create a factory default image. Follow Step 2 ~ Step 12 described in Section B.2.5 to create a factory default image. Step0: B.5 Recovery Tool Functions After completing the initial setup procedures as described above, users can access the recovery tool by pressing while booting up the system. However, if the setup procedure in Section B.
PAGE 164
NANO-QM770 EPIC SBC Figure B-35: Recovery Tool Main Menu The recovery tool has several functions including: 1. Factory Restore: Restore the factory default image (iei.GHO) created in Section B.2.5. 2. Backup system: Create a system backup image (iei_user.GHO) which will be saved in the hidden partition. 3. Restore your last backup: Restore the last system backup image 4. Manual: Enter the Symantec Ghost window to configure manually. 5. Quit: Exit the recovery tool and restart the system.
PAGE 165
NANO-QM770 EPIC SBC B.5.1 Factory Restore To restore the factory default image, please follow the steps below. Step 1: Type <1> and press in the main menu. Step 2: The Symantec Ghost window appears and starts to restore the factory default. A factory default image called iei.GHO is created in the hidden Recovery partition. Figure B-36: Restore Factory Default Step 3: The screen shown in Figure B-37 appears when completed. Press any key to reboot the system.
PAGE 166
NANO-QM770 EPIC SBC B.5.2 Backup System To backup the system, please follow the steps below. Step 1: Type <2> and press in the main menu. Step 2: The Symantec Ghost window appears and starts to backup the system. A backup image called iei_user.GHO is created in the hidden Recovery partition. Figure B-38: Backup System Step 3: The screen shown in Figure B-39 appears when system backup is complete. Press any key to reboot the system.
PAGE 167
NANO-QM770 EPIC SBC B.5.3 Restore Your Last Backup To restore the last system backup, please follow the steps below. Step 1: Type <3> and press in the main menu. Step 2: The Symantec Ghost window appears and starts to restore the last backup image (iei_user.GHO). Figure B-40: Restore Backup Step 3: The screen shown in Figure B-41 appears when backup recovery is complete. Press any key to reboot the system.
PAGE 168
NANO-QM770 EPIC SBC B.5.4 Manual To restore the last system backup, please follow the steps below. Step 1: Type <4> and press in the main menu. Step 2: The Symantec Ghost window appears. Use the Ghost program to backup or recover the system manually. Figure B-42: Symantec Ghost Window Step 3: When backup or recovery is completed, press any key to reboot the system.
PAGE 169
NANO-QM770 EPIC SBC B.6 Restore Systems from a Linux Server through LAN The One Key Recovery allows a client system to automatically restore to a factory default image saved in a Linux system (the server) through LAN connectivity after encountering a Blue Screen of Death (BSoD) or a hang for around 10 minutes. To be able to use this function, the client system and the Linux system MUST reside in the same domain.
PAGE 170
NANO-QM770 EPIC SBC B.6.1 Configure DHCP Server Settings Step 1: Install the DHCP #yum install dhcp (CentOS, commands marked in red) #apt-get install dhcp3-server (Debian, commands marked in blue) Step 2: Confirm the operating system default settings: dhcpd.conf. CentOS Use the following command to show the DHCP server sample location: #vi /etc/dhcpd.conf The DHCP server sample location is shown as below: Use the following command to copy the DHCP server sample to etc/dhcpd.conf: #cp /usr/share/doc/dhcp-3.
PAGE 171
NANO-QM770 EPIC SBC filename “pxelinux.0”; B.6.2 Configure TFTP Settings Step 1: Install the tftp, httpd and syslinux. #yum install tftp-server httpd syslinux (CentOS) #apt-get install tftpd-hpa xinetd syslinux (Debian) Step 2: Enable the TFTP server by editing the “/etc/xinetd.d/tftp” file and make it use the remap file. The “-vvv” is optional but it could definitely help on getting more information while running the remap file. For example: CentOS #vi /etc/xinetd.
PAGE 172
NANO-QM770 EPIC SBC Debian Replace the TFTP settings from “inetd” to “xinetd” and annotate the “inetd” by adding “#”. #vi /etc/inetd.conf Modify: #tftp dgram udp wait root /usr/sbin....... (as shown below) #vi /etc/xinetd.d/tftp B.6.3 Configure One Key Recovery Server Settings Step 1: Copy the Utility/RECOVERYR10.TAR.BZ2 package from the One Key Recovery CD to the system (server side). Step 2: Extract the recovery package to /. #cp RecoveryR10.tar.bz2 / #cd / #tar –xvjf RecoveryR10.tar.
PAGE 173
NANO-QM770 EPIC SBC B.6.4 Start the DHCP, TFTP and HTTP Start the DHCP, TFTP and HTTP. For example: CentOS #service xinetd restart #service httpd restart #service dhcpd restart Debian #/etc/init.d/xinetd reload #/etc/init.d/xinetd restart #/etc/init.d/dhcp3-server restart B.6.5 Create Shared Directory Step 1: Install the samba. #yum install samba Step 2: Create a shared directory for the factory default image. #mkdir /share #cd /share #mkdir /image #cp iei.
PAGE 174
NANO-QM770 EPIC SBC Modify: [image] comment = One Key Recovery path = /share/image browseable = yes writable = yes public = yes create mask = 0644 directory mask = 0755 Step 4: Edit “/etc/samba/smb.conf” for your environment. For example: Step 5: Modify the hostname #vi /etc/hostname Modify: RecoveryServer B.6.6 Setup a Client System for Auto Recovery Step 1: Disable the automatically restart function before creating the factory default image. Go to: My Computer Æ Properties Æ Advanced.
PAGE 175
NANO-QM770 EPIC SBC Figure B-43: Disable Automatically Restart Step 2: Configure the following BIOS options of the client system. Advanced → iEi Feature → Auto Recovery Function → Enabled Advanced → iEi Feature → Recover from PXE → Enabled Boot → Launch PXE OpROM → Enabled Step 3: Continue to configure the Boot Option Priorities BIOS option of the client system: Boot Option #1 Æ remain the default setting to boot from the original OS. Boot Option #2 Æ select the boot from LAN option.
PAGE 176
NANO-QM770 EPIC SBC MUST be installed in the system, otherwise, the system will automatically restore from the factory default image every ten (10) minutes. Step 6: Restart the client system from LAN. If the system encounters a Blue Screen of Death (BSoD) or a hang for around 10 minutes, it will automatically restore from the factory default image. The following screens will show when the system starts auto recovering.
PAGE 177
NANO-QM770 EPIC SBC NOTE: A firewall or a SELinux is not in use in the whole setup process described above. If there is a firewall or a SELinux protecting the system, modify the configuration information to accommodate them. B.7 Other Information B.7.1 Using AHCI Mode or ALi M5283 / VIA VT6421A Controller When the system uses AHCI mode or some specific SATA controllers such as ALi M5283 or VIA VT6421A, the SATA RAID/AHCI driver must be installed before using one key recovery.
PAGE 178
NANO-QM770 EPIC SBC Step 5: When the following window appears, press ~~to select “Specify Additional Device”.~~
~~PAGE 179~~
NANO-QM770 EPIC SBC Step 6: In the following window, select a SATA controller mode used in the system. Then press . The user can now start using the SATA HDD. Step 7: After pressing , the system will get into the recovery tool setup menu. Continue to follow the setup procedure from Step 4 in Section B.2.2 Create Partitions to finish the whole setup process.Step7: B.7.
~~PAGE 180~~
~~NANO-QM770 EPIC SBC Appendix C C Terminology Page 165~~
~~PAGE 181~~
NANO-QM770 EPIC SBC AC ’97 Audio Codec 97 (AC’97) refers to a codec standard developed by Intel® in 1997. ACPI Advanced Configuration and Power Interface (ACPI) is an OS-directed configuration, power management, and thermal management interface. AHCI Advanced Host Controller Interface (AHCI) is a SATA Host controller register-level interface. ATA The Advanced Technology Attachment (ATA) interface connects storage devices including hard disks and CD-ROM drives to a computer.
~~PAGE 182~~
NANO-QM770 EPIC SBC DMA Direct Memory Access (DMA) enables some peripheral devices to bypass the system processor and communicate directly with the system memory. DIMM Dual Inline Memory Modules are a type of RAM that offer a 64-bit data bus and have separate electrical contacts on each side of the module. DIO The digital inputs and digital outputs are general control signals that control the on/off circuit of external devices or TTL devices.
~~PAGE 183~~
NANO-QM770 EPIC SBC LCD Liquid crystal display (LCD) is a flat, low-power display device that consists of two polarizing plates with a liquid crystal panel in between. LVDS Low-voltage differential signaling (LVDS) is a dual-wire, high-speed differential electrical signaling system commonly used to connect LCD displays to a computer. POST The Power-on Self Test (POST) is the pre-boot actions the system performs when the system is turned-on.
~~PAGE 184~~
~~NANO-QM770 EPIC SBC Appendix D D Digital I/O Interface Page 169~~
~~PAGE 185~~
NANO-QM770 EPIC SBC D.1 Introduction The DIO connector on the NANO-QM770 is interfaced to GPIO ports on the Super I/O chipset. The DIO has both 4-bit digital inputs and 4-bit digital outputs. The digital inputs and digital outputs are generally control signals that control the on/off circuit of external devices or TTL devices. Data can be read or written to the selected address to enable the DIO functions. NOTE: For further information, please refer to the datasheet for the Super I/O chipset. D.
~~PAGE 186~~
~~NANO-QM770 EPIC SBC D.3.2 Enable the DIO Output Function The BIOS interrupt call INT 15H controls the digital I/O. An assembly program to enable digital I/O output functions is listed below.~~
~~PAGE 187~~
~~NANO-QM770 EPIC SBC Appendix E E Hazardous Materials Disclosure Page 172~~
~~PAGE 188~~
NANO-QM770 EPIC SBC E.1 Hazardous Materials Disclosure Table for IPB Products Certified as RoHS Compliant Under 2002/95/EC Without Mercury The details provided in this appendix are to ensure that the product is compliant with the Peoples Republic of China (China) RoHS standards. The table below acknowledges the presences of small quantities of certain materials in the product, and is applicable to China RoHS only.
~~PAGE 189~~
NANO-QM770 EPIC SBC Part Name Toxic or Hazardous Substances and Elements Lead Mercury Cadmium Hexavalent Polybrominated Polybrominated (Pb) (Hg) (Cd) Chromium Biphenyls Diphenyl (CR(VI)) (PBB) Ethers (PBDE) Housing X O O O O X Display X O O O O X Printed Circuit X O O O O X X O O O O O X O O O O X Fan Assembly X O O O O X Power Supply X O O O O X O O O O O O Board Metal Fasteners Cable Assembly Assemblies Battery O: This toxic or hazardo
~~PAGE 190~~
NANO-QM770 EPIC SBC 此附件旨在确保本产品符合中国 RoHS 标准。以下表格标示此产品中某有毒物质的含量符合中国 RoHS 标准规定的限量要求。本产品上会附有”环境友好使用期限”的标签，此期限是估算这些物质”不会有泄漏或突变”的年限。本产品可能包含有较短的环境友好使用期限的可替换元件，像是电池或灯管，这些元件将会单独标示出来。部件名称有毒有害物质或元素铅汞镉六价铬多溴联苯多溴二苯 (Pb) (Hg) (Cd) (CR(VI)) (PBB) 醚 (PBDE) 壳体 X O O O O X 显示 X O O O O X 印刷电路板 X O O O O X 金属螺帽 X O O O O O 电缆组装 X O O O O X 风扇组装 X O O O O X 电力供应组装 X O O O O X 电池 O O O O O O O: 表示该有毒有害物质在该部件所有物质材料中的含量均在 SJ/T11363-2006 标准规定的限量要求以下。