Manual

ManualsBrandsIEI Integration ManualsHardwarePCISA-9652 v1.01

PCISA -9652 Half-Size CPU Card

Page i

PCISA-9652 Half-size CPU Card

Summary of content (232 pages)

PAGE 1
PCISA -9652 Half-Size CPU Card PCISA-9652 Half-size CPU Card Page i
PAGE 2
PCISA-9652 Half-Size CPU Card Revision Date Version Changes 2008-08 1.01 Modified part numbers of the SATA cable, SATA power cable and USB cable 2008-04 Page ii 1.
PAGE 3
PCISA -9652 Half-Size CPU Card Copyright COPYRIGHT NOTICE The information in this document is subject to change without prior notice in order to improve reliability, design and function and does not represent a commitment on the part of the manufacturer. In no event will the manufacturer be liable for direct, indirect, special, incidental, or consequential damages arising out of the use or inability to use the product or documentation, even if advised of the possibility of such damages.
PAGE 4
PCISA-9652 Half-Size CPU Card Manual Conventions WARNING! Warnings appear where overlooked details may cause damage to the equipment or result in personal injury. Warnings should be taken seriously. Warnings are easy to recognize. The word “warning” is written as “WARNING,” both capitalized and bold and is followed by text. The text is the warning message. A warning message is shown below: WARNING: This is an example of a warning message.
PAGE 5
PCISA -9652 Half-Size CPU Card CAUTION: This is an example of a caution message. Failure to adhere to cautions messages may result in permanent damage to the PCISA-9652. Please take caution messages seriously. NOTE: These messages inform the reader of essential but non-critical information. These messages should be read carefully as any directions or instructions contained therein can help avoid making mistakes. Notes are easy to recognize.
PAGE 6
PCISA-9652 Half-Size CPU Card Packing List NOTE: If any of the components listed in the checklist below are missing, please do not proceed with the installation. Contact the IEI reseller or vendor you purchased the PCISA-9652 from or contact an IEI sales representative directly. To contact an IEI sales representative, please send an email to sales@iei.com.tw. The items listed below should all be included in the PCISA-9652 package.
PAGE 7
PCISA -9652 Half-Size CPU Card Table of Contents 1 INTRODUCTION..................................................................................................... 1 1.1 PCISA-9652 OVERVIEW ............................................................................................ 2 1.1.1 PCISA-9652 Features ........................................................................................ 2 1.2 PCISA-9652 BOARD OVERVIEW .............................................................................
PAGE 8
PCISA-9652 Half-Size CPU Card 2.6.6 Intel® ICH8ME PCIe x1 Bus............................................................................ 23 2.6.7 Intel® ICH8ME Real Time Clock ..................................................................... 23 2.6.8 Intel® ICH8ME SATA Controller ..................................................................... 23 2.6.9 Intel® ICH8ME Serial Peripheral Interface (SPI) BIOS ................................. 24 2.6.10 Intel® ICH8ME USB Controller .....................
PAGE 9
PCISA -9652 Half-Size CPU Card 4.1.1 PCISA-9652 Layout ......................................................................................... 40 4.1.2 Peripheral Interface Connectors ..................................................................... 41 4.1.3 Rear Panel Connectors .................................................................................... 42 4.2 INTERNAL PERIPHERAL CONNECTORS ...................................................................... 43 4.2.1 AT Power Connector....
PAGE 10
PCISA-9652 Half-Size CPU Card 5.3 CPU, CPU COOLING KIT AND DIMM INSTALLATION ............................................. 77 5.3.1 Socket P CPU Installation ............................................................................... 77 5.3.2 Cooling Kit CF-479B-RS Installation.............................................................. 79 5.3.3 DIMM Installation ........................................................................................... 81 5.4 JUMPER SETTINGS .........................
PAGE 11
PCISA -9652 Half-Size CPU Card 6.3.2 IDE Configuration ......................................................................................... 107 6.3.2.1 IDE Master, IDE Slave ........................................................................... 109 6.3.3 Floppy Configuration......................................................................................114 6.3.4 Super IO Configuration...................................................................................115 6.3.
PAGE 12
PCISA-9652 Half-Size CPU Card C DIO INTERFACE................................................................................................. 187 C.1 DIO INTERFACE INTRODUCTION ........................................................................... 188 C.2 DIO CONNECTOR PINOUTS ................................................................................... 188 C.3 ASSEMBLY LANGUAGE SAMPLES ........................................................................... 189 C.3.
PAGE 13
PCISA -9652 Half-Size CPU Card List of Figures Figure 1-1: PCISA-9652 CPU Card...............................................................................2 Figure 1-2: PCISA-9652 Board Overview (Front Side)...............................................3 Figure 1-2: PCISA-9652 Board Overview (Solder Side).............................................4 Figure 2-1: PCISA-9652 Dimensions (mm) ...............................................................
PAGE 14
PCISA-9652 Half-Size CPU Card Figure 4-11: IDE Device Connector Location ...........................................................55 Figure 4-12: Infrared Connector Pinout Locations ..................................................56 Figure 4-13: Keyboard Connector Location .............................................................57 Figure 4-14: LCD Backlight Connector Location .....................................................58 Figure 4-15: LVDS LCD Connector Location............................
PAGE 15
PCISA -9652 Half-Size CPU Card Figure 5-18: LAN Connection.....................................................................................98 Figure 5-19: VGA Connector ......................................................................................99 Figure 5-20: USB Device Connection..................................................................... 100 Figure 7-1: Introduction Screen..............................................................................
PAGE 16
PCISA-9652 Half-Size CPU Card Figure 7-30: Setup Type .......................................................................................... 162 Figure 7-31: Intel® 82573 Driver Installation Progress ........................................ 162 Figure 7-32: Select the Audio CODEC.................................................................... 164 Figure 7-33: Select the OS....................................................................................... 165 Figure 7-34: Select the OS Version ..
PAGE 17
PCISA -9652 Half-Size CPU Card List of Tables Table 1-1: Technical Specifications ............................................................................7 Table 2-1: Supported Intel® Processors...................................................................13 Table 2-2: Supported HDD Specifications ................................................................20 Table 2-3: Power Consumption .................................................................................
PAGE 18
PCISA-9652 Half-Size CPU Card Table 4-23: USB3 and USB4 Pinouts.........................................................................68 Table 4-24: VGA Connector Pinouts .........................................................................70 Table 4-25: LAN1 and LAN2 Pinouts .........................................................................70 Table 4-26: RJ-45 Ethernet Connector LEDs............................................................71 Table 4-27: External USB Connector Pinouts ......
PAGE 19
PCISA -9652 Half-Size CPU Card List of BIOS Menus Menu 1: Main ................................................................................................. 104 Menu 2: Advanced.................................................................................................... 106 Menu 3: CPU Configuration .................................................................................... 107 Menu 4: IDE Configuration ..................................................................................
PAGE 20
PCISA-9652 Half-Size CPU Card THIS PAGE IS INTENTIONALLY LEFT BLANK Page xx
PAGE 21
PCISA -9652 Half-Size CPU Card Chapter 1 1 Introduction Page 1
PAGE 22
PCISA-9652 Half-Size CPU Card 1.1 PCISA-9652 Overview Figure 1-1: PCISA-9652 CPU Card The PCISA-9652 half-size PCISA CPU card is a Socket P Intel® CoreTM2 Duo (Merom core) CPU platform. The PCISA-9652 has a maximum front side bus (FSB) frequency of 800 MHz and comes with a VGA interface and dual PCI Express (PCIe) Gigabit Ethernet (GbE). The PCISA-9652 supports up to three, second-generation serial ATA (SATA) hard disk drives (HDD) with maximum transfer rates of 3.0 Gbps and up to six USB 2.0 devices.
PAGE 23
PCISA -9652 Half-Size CPU Card Supports six USB 2.0 devices Supports HDTV-Out, 24-bit dual-channel LVDS and CRT 1.
PAGE 24
PCISA-9652 Half-Size CPU Card Figure 1-3: PCISA-9652 Board Overview (Solder Side) 1.2.
PAGE 25
PCISA -9652 Half-Size CPU Card 1 x Infrared interface connector 1 x Keyboard connector 1 x LCD backlight connector 1 x LVDS LCD connector 1 x Parallel port connector 1 x RS-232 serial port connector 1 x RS-232/422/485 serial port connector 3 x SATA II connectors 1 x SDVO connector 1 x TV out connector 2 x USB connectors The PCISA-9652 has the following connectors on the board rear panel: 1 x CRT connector 2 x Ethernet connectors 2 x USB 2.
PAGE 26
PCISA-9652 Half-Size CPU Card 1.2.2 Technical Specifications PCISA-9652 technical specifications are listed in Table 1-1. Detailed descriptions of each specification can be found in Chapter 2.
PAGE 27
PCISA -9652 Half-Size CPU Card Amplitude Shift Keyed IR (ASKIR) Digital I/O 8-bit digital I/O, 4 input / 4 output by super I/O Audio Supports 7.1 channel HD audio via AC-KIT883HD audio kit Ethernet Dual Intel® 82573L PCIe GbE controllers BIOS AMI BIOS Label Power AT and ATX power Power Consumption 5V @ 7.72 A, +12V @ 0.139 A (2.
PAGE 28
PCISA-9652 Half-Size CPU Card THIS PAGE IS INTENTIONALLY LEFT BLANK Page 8
PAGE 29
PCISA -9652 Half-Size CPU Card Chapter 2 2 Detailed Specifications Page 9
PAGE 30
PCISA-9652 Half-Size CPU Card 2.1 Overview This chapter describes the specifications and on-board features of the PCISA-9652 in detail. 2.2 Dimensions 2.2.1 Board Dimensions The dimensions of the board are listed below: Length: 185.0 mm Width: 127.
PAGE 31
PCISA -9652 Half-Size CPU Card 2.2.2 External Interface Panel Dimensions External peripheral interface connector panel dimensions are shown in Figure 2-2. Figure 2-2: External Interface Panel Dimensions (mm) 2.3 Data Flow The PCISA-9652 motherboard comes with an Intel® GME965 GMCH and an Intel® ICH8ME I/O Controller Hub. Figure 2-3 shows the data flow between the system chipset, the CPU and other components installed on the motherboard.
PAGE 32
PCISA-9652 Half-Size CPU Card Figure 2-3: Data Flow Block Diagram Page 12
PAGE 33
PCISA -9652 Half-Size CPU Card 2.4 Compatible Processors Table 2-1 lists the Intel® processors supported on the PCISA-9652. All the processors in Table 2-1 are 65nm Socket P processors. Processor Max. CPU Speed FSB Speed Max. Cache Size Intel® Core2 Duo 2.60 GHz 800 MHz 4 MB Intel® Celeron® M 2.13 GHz 533 MHz 1 MB Table 2-1: Supported Intel® Processors 2.5 Intel® GME965 Graphics and Memory Controller Hub 2.5.
PAGE 34
PCISA-9652 Half-Size CPU Card Figure 2-4: Front Side Bus (FSB) 2.5.3 Intel® GME965 Memory Support WARNING: Only DDR2 memory module can be installed on the PCISA-9652. Do not install DDR memory modules. If a DDR memory module is installed on the PCISA-9652, the PCISA-9652 may be irreparably damaged.
PAGE 35
PCISA -9652 Half-Size CPU Card Figure 2-5: 240-pin DDR2 DIMM Socket 2.5.
PAGE 36
PCISA-9652 Half-Size CPU Card Figure 2-6: Integrated Graphics Interfaces 2.5.4.1 Intel® GME965 Analog CRT Support A DB-15 VGA connector on the external peripheral interface connector panel is interfaced to the Intel® GME965 graphics engine. The Intel® GME965 internal graphics engine, with an integrated 300 MHz RAMDAC and hot plug CRT support, supports analog CRT monitors up to QXGA (2048 x 1536). 2.5.4.
PAGE 37
PCISA -9652 Half-Size CPU Card Three integrated 10-bit DACs Overscaling NTSC and PAL formats supported Supports Component, S-Video, TV D connector or Composite output connectivity Supports with the following resolutions: o o o o SDTV 480i EDTV 480p HDTV 720p, 1080i True HDTV 1080p 2.5.4.
PAGE 38
PCISA-9652 Half-Size CPU Card Figure 2-7: DMI Chip-to-Chip Connection Features of the Intel® GME965 DMI are listed below: 2GB/s (1GB/s in each direction) bus speed Configurable as x2 or x4 DMI lanes 32-bit downstream address 2.6 Intel® ICH8ME I/O Controller Hub 2.6.1 Intel® ICH8ME Overview The Intel® ICH8ME I/O Controller Hub (ICH) is connected to the Intel® GME965 GMCH through the chip-to-chip Direct Media Interface (DMI). Some of the features of the Intel® ICH8ME are listed below.
PAGE 39
PCISA -9652 Half-Size CPU Card connectors on the PCISA-9652 Supports the six USB 2.0 devices on the PCISA-9652 with four UHCI controllers and one EHCI controller Complies with System Management Bus (SMBus) Specification, Version 2.0 Supports Intel® High Definition Audio Contains Low Pin Count (LPC) interface Supports Firmware Hub (FWH) interface Serial Peripheral Interface (SPI) support 2.6.
PAGE 40
PCISA-9652 Half-Size CPU Card Figure 2-8: Audio Connector 2.6.3 Intel® ICH8ME IDE Interface The integrated IDE interface on the ICH8ME supports two IDE hard disks and ATAPI devices. PIO IDE transfers up to 16 MB/s and Ultra ATA transfers of 100MB/s.
PAGE 41
PCISA -9652 Half-Size CPU Card 2.6.4 Intel® ICH8ME Low Pin Count (LPC) Interface The ICH8ME LPC interface complies with the LPC 1.1 specifications. The LPC bus from the ICH7 is connected to the ITE IT8712F Super I/O chipset. For more detailed information please refer to Section 2.8.2. 2.6.5 Intel® ICH8ME PCI Interface The PCI bus on the ICH8ME is compliant with the PCI Revision 2.3 implementation. Some of the features of the PCI interface are listed below. PCI Revision 2.
PAGE 42
PCISA-9652 Half-Size CPU Card Figure 2-9: PCI-to-ISA Bridge The ITE IT8888G has a PCI specification v2.1 compliant 32-bit PCI bus interface and supports both PCI Bus master and slave. The PCI interface supports both programmable positive and full subtractive decoding schemes. Some of the features of the IT8888G PCI to ISA bridge are listed below.
PAGE 43
PCISA -9652 Half-Size CPU Card 2.6.6 Intel® ICH8ME PCIe x1 Bus The Intel® ICH8ME GMCH has six PCIe x1 lanes. Two of the six PCIe lanes are implemented on the PCISA-9652, including: Two PCIe x1 lanes are connected to two Intel® 82573L GbE controllers For more detailed information, please refer to Section 2.7. 2.6.7 Intel® ICH8ME Real Time Clock 256 bytes of battery backed RAM is provided by the Motorola MC146818A real time clock (RTC) integrated into the ICH8ME. The RTC operates on a 3V battery and 32.
PAGE 44
PCISA-9652 Half-Size CPU Card 2.6.9 Intel® ICH8ME Serial Peripheral Interface (SPI) BIOS The 4-pin SPI is connected to an SPI BIOS chip. A licensed copy of AMI BIOS is preinstalled on the SPI BIOS chip. A master-slave protocol is used for communication on the SPI bus. The slave is connected to the Intel® ICH8ME and is implemented as a tri-state bus. 2.6.10 Intel® ICH8ME USB Controller Up to eight high-speed, full-speed or low-speed USB devices are supported by the ICH8ME on the PCISA-9652.
PAGE 45
PCISA -9652 Half-Size CPU Card Two PCIe x1 lanes are connected to two Intel® PCIe GbE connectors 2.7.2 Intel® 82573L PCIe GbE Controller Two RJ-45 Ethernet LAN connectors are interfaced directly to two Intel® 82573L PCIe GbE controllers. The Intel® 82573L PCIe GbE controller is a compact, single-port integrated physical layer (PHY) device with its own Memory Access Controller (MAC) and interfaced to the Intel® ICH8ME Southbridge through a PCIe x1 lane.
PAGE 46
PCISA-9652 Half-Size CPU Card Mechanism for reducing interrupts from Tx/Rx operations Integrated PHY for 10/100/1000 Mbps (full- and half-duplex) IEEE 802.3ab* auto-negotiation support IEEE 802.3ab PHY compliance and compatibility Tx/Rx IP,TCP,and UDP checksum offloading Tx TCP segmentation IEEE 802.1q* Virtual Local Area Network (VLAN) support with VLAN tag insertion, stripping, and packet filtering for up to 4096 VLAN tags Boot ROM Preboot eXecution Environment (PXE) Flash interface support SDG 3.0,WfM 3.
PAGE 47
PCISA -9652 Half-Size CPU Card The iTE IT8712F is an LPC interface-based Super I/O device that comes with Environment Controller integration.
PAGE 48
PCISA-9652 Half-Size CPU Card 2.8.2.4 Super I/O Fan Speed Controller The Super I/O fan speed controller enables the system to monitor the speed of the fan. One of the pins on the fan connector is reserved for fan speed detection and interfaced to the fan speed controller on the Super I/O. The fan speed is then reported in the BIOS. 2.8.2.5 Super I/O GPIO Ports The Super I/O has 38 programmable GPIO pins of which 8 are implemented on the PCISA-9652.
PAGE 49
PCISA -9652 Half-Size CPU Card The parallel port controller is connected to an on-board LPT connector on the PCISA-9652. 2.8.2.9 Super I/O Floppy Disk Drive (FDD) Controller The Super I/O FDD controller is compatible with the following specifications. FDD anti-virus functions with software write protect and FDD write enable signal Supports 3.5-inch or 5.25-inch FDD Compatible with industry standard 82077 Supported capacities: o o o o o 360K 720K 1.2M 1.44M 2.
PAGE 50
PCISA-9652 Half-Size CPU Card Eight voltage inputs on the PCISA-9652 Super I/O Enhanced Hardware Monitor monitor the following voltages: CPU Core +1.8V +3.30V +5.00V +12.0V +1.05V +1.5V +1.25V VBAT The PCISA-9652 Super I/O Enhanced Hardware Monitor also monitors the following fan speed: CPU Fan speed The values for the above environmental parameters are all recorded in the BIOS Hardware Health Configuration menu. 2.9.
PAGE 51
PCISA -9652 Half-Size CPU Card Table 2-3 shows the power consumption parameters for the PCISA-9652 running with a 2.0GHz Intel® Core™2 Duo T7300 with a 800 MHz FSB and a 667 MHz 1 GB DDR2 DIMM, Voltage Current +5V 7.72 A +12V 0.
PAGE 52
PCISA-9652 Half-Size CPU Card THIS PAGE IS INTENTIONALLY LEFT BLANK Page 32
PAGE 53
PCISA -9652 Half-Size CPU Card Chapter 3 3 Unpacking Page 33
PAGE 54
PCISA-9652 Half-Size CPU Card 3.1 Anti-static Precautions WARNING: Failure to take ESD precautions during the installation of the PCISA-9652 may result in permanent damage to the PCISA-9652 and severe injury to the user. Electrostatic discharge (ESD) can cause serious damage to electronic components, including the PCISA-9652. Dry climates are especially susceptible to ESD.
PAGE 55
PCISA -9652 Half-Size CPU Card 3.3 Unpacking Checklist NOTE: If some of the components listed in the checklist below are missing, please do not proceed with the installation. Contact the IEI reseller or vendor you purchased the PCISA-9652 from or contact an IEI sales representative directly. To contact an IEI sales representative, please send an email to sales@iei.com.tw. 3.3.
PAGE 56
PCISA-9652 Half-Size CPU Card 1 Mini jumper pack 1 Quick Installation Guide 1 Dual port USB cable (P/N: CB-USB02-RS) 1 Utility CD Table 3-1: Package List Contents 3.3.2 Optional Items NOTE: The items listed in this section are optional items that must be ordered separately. Please contact your PCISA-9652 vendor, distributor or reseller for more information or, contact IEI directly by sending an email to sales@iei.com.tw. The following optional items are available for the PCISA-9652.
PAGE 57
PCISA -9652 Half-Size CPU Card Quantity 1 Item and Part Number Image CPU Cooler (P/N: CF-479B-RS) 1 FDD cable (P/N: 32200-000058-RS) 1 KB/MS cable with bracket (P/N: 19800-000075-RS) 1 HDTV cable set with S-Video/Composite/Component interfaces (P/N: HDTVCABLESET-01) 1 RS-232/422/485 cable (P/N: 32200-000077-RS) Table 3-2: Optional Items Page 37
PAGE 58
PCISA-9652 Half-Size CPU Card THIS PAGE IS INTENTIONALLY LEFT BLANK Page 38
PAGE 59
PCISA -9652 Half-Size CPU Card Chapter 4 4 Connectors and Jumpers Page 39
PAGE 60
PCISA-9652 Half-Size CPU Card 4.1 Peripheral Interface Connectors Section 4.1.1 shows peripheral interface connector locations. Section 4.1.2 lists all the peripheral interface connectors seen in Section 4.1.1. 4.1.1 PCISA-9652 Layout Figure 4-1 shows the on-board peripheral connectors, backplane peripheral connectors and on-board jumpers.
PAGE 61
PCISA -9652 Half-Size CPU Card Figure 4-2: Connector and Jumper Locations (Solder Side) 4.1.2 Peripheral Interface Connectors Table 4-1 shows a list of the peripheral interface connectors on the PCISA-9652. Detailed descriptions of these connectors can be found in Section 4.2.
PAGE 62
PCISA-9652 Half-Size CPU Card FDD connector 34-pin header FDD1 Flash SPI ROM connector 8-pin header JSPI1 Front panel connector 8-pin header F_PANEL1 IDE Interface connector 40-pin box header PIDE1 Infrared interface connector 5-pin header IR1 Keyboard connector 6-pin wafer KB_MS1 LCD backlight connector 5-pin wafer connector INVERTER1 LVDS LCD connector 30-pin crimp connector LVDS1 Parallel port connector 26-pin header LPT1 SATA drive connector (1) 7-pin SATA connector S_ATA1
PAGE 63
PCISA -9652 Half-Size CPU Card Connector Type Label CRT connector 15-pin female connector VGA1 Ethernet connector (1) RJ-45 connector LAN1 Ethernet connector (2) RJ-45 connector LAN2 USB 2.0 port (1) USB port connector USB_C4 USB 2.0 port (2) USB port connector USB_C5 Table 4-2: Rear Panel Connectors 4.2 Internal Peripheral Connectors Internal peripheral connectors are found on the motherboard and are only accessible when the motherboard is outside of the chassis.
PAGE 64
PCISA-9652 Half-Size CPU Card Figure 4-3: AT Power Connector Location PIN NO. DESCRIPTION 1 +12V 2 GND 3 GND 4 +5V Table 4-3: AT Power Connector Pinouts 4.2.2 ATX Power Supply Enable Connector CN Label: ATXCTL1 CN Type: 3-pin wafer (1x3) CN Location: See Figure 4-4 CN Pinouts: See Table 4-4 The ATX power supply enable connector enables the PCISA-9652 to be connected to an ATX power supply.
PAGE 65
PCISA -9652 Half-Size CPU Card Figure 4-4: ATX Power Supply Enable Connector Location PIN NO. DESCRIPTION 1 GND 2 PS-ON 3 +5V Standby Table 4-4: ATX Power Supply Enable Connector Pinouts 4.2.3 Audio Connector CN Label: J_AUDIO1 CN Type: 10-pin header (2x5) CN Location: See Figure 4-5 CN Pinouts: See Table 4-5 The audio connector connects to the optional audio kit to provide 7.1 channel HD audio to the system.
PAGE 66
PCISA-9652 Half-Size CPU Card Figure 4-5: Audio Connector Location PIN NO. DESCRIPTION PIN NO. DESCRIPTION 1 HDA_SYNC 2 HDA_BITCLK 3 HDA_SDOUT 4 SB_SPKR 5 HDA_SDIN0 6 HDA_RST# 7 VCC 8 GND 9 +12V 10 GND Table 4-5: Audio Connector Pinouts 4.2.4 CompactFlash® Socket CN Label: CF1 (solder side) CN Type: 50-pin slot (2x25) CN Location: See Figure 4-6 CN Pinouts: See Table 4-6 A CF Type I or Type II memory card is inserted to the CF socket on the solder side of the PCISA-9652.
PAGE 67
PCISA -9652 Half-Size CPU Card Figure 4-6: CF Card Socket Location Page 47
PAGE 68
PCISA-9652 Half-Size CPU Card PIN NO. DESCRIPTION PIN NO.
PAGE 69
PCISA -9652 Half-Size CPU Card CN Location: See Figure 4-7 CN Pinouts: See Table 4-7 The DIO connector is managed through a Super I/O chip. The DIO connector pins are user programmable. The digital IO port of PCISA-9652 is 5V CMOS level. Figure 4-7: GPIO Connector Location PIN NO. DESCRIPTION PIN NO. DESCRIPTION 1 GND 2 VCC 3 OUTPUT 3 4 OUTPUT 2 5 OUTPUT 1 6 OUTPUT 0 7 INPUT 3 8 INPUT 2 9 INPUT 1 10 INPUT 0 Table 4-7: GPIO Connector Pinouts 4.2.
PAGE 70
PCISA-9652 Half-Size CPU Card CN Pinouts: See Table 4-8 The cooling fan connector provides a 12V, 500mA current to a CPU cooling fan. The connector has a "rotation" pin to get rotation signals from fans and notify the system so the system BIOS can recognize the fan speed. Please note that only specified fans can issue the rotation signals. Figure 4-8: Fan Connector Locations PIN NO. DESCRIPTION 1 GND 2 +12V 3 Rotation Signal 4 Control Table 4-8: Fan Connector Pinouts 4.2.
PAGE 71
PCISA -9652 Half-Size CPU Card CN Location: See Figure 4-9 CN Pinouts: See Table 4-9 The floppy disk connector is connected to a floppy disk drive. Figure 4-9: 34-pin FDD Connector Location PIN NO. DESCRIPTION PIN NO.
PAGE 72
PCISA-9652 Half-Size CPU Card 27 GND 28 WRITE PROTECT# 29 GND 30 READ DATA# 31 GND 32 SIDE 1 SELECT# 33 GND 34 DISK CHANGE# Table 4-9: 34-pin FDD Connector Pinouts 4.2.8 Flash SPI ROM Connector CN Label: JSPI1 CN Type: 8-pin header (2x4) CN Location: See Figure 4-23 CN Pinouts: See Table 4-23 Use the Flash SPI ROM connector to flash SPI ROM. Figure 4-10: Flash SPI ROM Connector Locations PIN NO. DESCRIPTION PIN NO. DESCRIPTION 1 3.
PAGE 73
PCISA -9652 Half-Size CPU Card 7 NC 8 NC Table 4-10: Flash SPI ROM Connector Pinouts 4.2.9 Front Panel Connector CN Label: F_PANEL1 CN Type: 8-pin header (2x4) CN Location: See Figure 4-11 CN Pinouts: See Table 4-11 The front panel connector connects to several external switches and indicators to monitor and control the motherboard.
PAGE 74
PCISA-9652 Half-Size CPU Card FUNCTION PIN DESCRIPTION FUNCTION PIN DESCRIPTION Power 1 PWR_BTN+ Power 2 PWR_LED+ Button 3 PWR_BTN- LED 4 PWR_LED- HDD LED 5 HDD_LED+ Reset 6 RESET+ 7 HDD_LED- 8 RESET- Table 4-11: Front Panel Connector Pinouts 4.2.
PAGE 75
PCISA -9652 Half-Size CPU Card Figure 4-12: IDE Device Connector Location PIN NO. DESCRIPTION PIN NO.
PAGE 76
PCISA-9652 Half-Size CPU Card PIN NO. DESCRIPTION 39 HDD ACTIVE# PIN NO. 40 DESCRIPTION GND Table 4-12: IDE Connector Pinouts 4.2.11 Infrared Interface Connector CN Label: IR1 CN Type: 5-pin header (1x5) CN Location: See Figure 4-13 CN Pinouts: See Table 4-13 The infrared interface connector supports both Serial Infrared (SIR) and Amplitude Shift Key Infrared (ASKIR) interfaces. Figure 4-13: Infrared Connector Pinout Locations PIN NO.
PAGE 77
PCISA -9652 Half-Size CPU Card 4.2.12 Keyboard/Mouse Connector CN Label: KB_MS1 CN Type: 6-pin header (1x6) CN Location: See Figure 4-14 CN Pinouts: See Table 4-14 The keyboard/mouse connector can be connected to a standard PS/2 cable or PS/2 Y cable to add keyboard and mouse functionality to the system. Figure 4-14: Keyboard/Mouse Connector Location PIN NO. DESCRIPTION 1 VCC5_KBMS 2 MS DATA 3 MS CLK 4 KB DATA 5 KB CLK 6 KB GROUND Table 4-14: Keyboard/Mouse Connector Pinouts 4.2.
PAGE 78
PCISA-9652 Half-Size CPU Card CN Location: See Figure 4-15 CN Pinouts: See Table 4-15 The LCD backlight connector is for the LCD inverter connection. Figure 4-15: LCD Backlight Connector Location PIN NO. DESCRIPTION 1 BRIGHTNESS 2 GND1 3 12V 4 GND2 5 BL_EN Table 4-15: LCD Backlight Connector Pinouts 4.2.
PAGE 79
PCISA -9652 Half-Size CPU Card CN Pinouts: See Table 4-16 The connector supports one or two channel 24-bit LVDS panel. Figure 4-16: LVDS LCD Connector Location PIN NO. DESCRIPTION PIN NO.
PAGE 80
PCISA-9652 Half-Size CPU Card PIN NO. DESCRIPTION PIN NO. DESCRIPTION 19 2nd LVDS data2 output + 20 2nd LVDS data2 output - 21 2nd LVDS clock output + 22 2nd LVDS clock output - 23 2nd LVDS data3 output + 24 2nd LVDS data3 output - 25 GND 26 GND 27 +LCD (3.3V or 5V) 28 +LCD (3.3V or 5V) 29 +LCD (3.3V or 5V) 30 +LCD (3.3V or 5V) Table 4-16: LVDS LCD Connector Pinouts 4.2.
PAGE 81
PCISA -9652 Half-Size CPU Card PIN NO. DESCRIPTION PIN NO. DESCRIPTION 1 STROBE# 2 DATA 0 3 DATA 1 4 DATA 2 5 DATA 3 6 DATA 4 7 DATA 5 8 DATA 6 9 DATA 7 10 ACKNOWLEDGE 11 BUSY 12 PAPER EMPTY 13 PRINTER SELECT 14 AUTO FORM FEED # 15 ERROR# 16 INITIALIZE 17 PRINTER SELECT LN# 18 GROUND 19 GROUND 20 GROUND 21 GROUND 22 GROUND 23 GROUND 24 GROUND 25 GROUND 26 NC Table 4-17: Parallel Port Connector Pinouts 4.2.
PAGE 82
PCISA-9652 Half-Size CPU Card Figure 4-18: SATA Drive Connector Locations PIN NO. DESCRIPTION 1 GND 2 TXP 3 TXN 4 GND 5 RXN 6 RXP 7 GND Table 4-18: SATA Drive Connector Pinouts 4.2.17 SDVO Connector CN Label: CN1 CN Type: 47-pin connector (1x47) CN Location: See Figure 4-19 CN Pinouts: See Table 4-19 The 47-pin SDVO (Serial Digital Video Out) connector supports additional video signaling interfaces.
PAGE 83
PCISA -9652 Half-Size CPU Card Figure 4-19: SDVO Connector Pinout Locations PIN NO. DESCRIPTION PIN NO.
PAGE 84
PCISA-9652 Half-Size CPU Card 8 SDVOB_CLK- 32 SDVO1_STALL- 9 SDVOB_ CLK+ 33 SDVO1_STALL+ 10 GROUND 34 GROUND 11 SDVOB_GREEN- 35 SDVO_TVCLKIN- 12 SDVOB_GREEN+ 36 SDVO_TVCLKIN+ 13 GROUND 37 GROUND 14 SDVOC_INT+ 38 SDVO_CLK 15 SDVOC_INT+ 39 SDVO_DATA 16 GROUND 40 PCIRST 17 SDVOB_INT+ 41 +5VS 18 SDVOB_INT+ 42 +5VS 19 GROUND 43 +5VS 20 SDVOC_BLUE- 44 NC 21 SDVOC_BLUE+ 45 NC 22 GROUND 46 GROUND 23 SDVOC_RED- 47 GROUND 24 SDVOC_RED+ Table 4-19: SDVO
PAGE 85
PCISA -9652 Half-Size CPU Card Figure 4-20: RS-232 Connector Pinout Locations PIN NO. DESCRIPTION PIN NO. DESCRIPTION 1 Data Carrier Direct (DCD) 2 Data Set Ready (DSR) 3 Receive Data (RXD) 4 Request To Send (RTS) 5 Transmit Data (TXD) 6 Clear To Send (CTS) 7 Data Terminal Ready (DTR) 8 Ring Indicator (RI) 9 Ground (GND) 10 Ground (GND) Table 4-20: RS-232 Connector Pinouts 4.2.
PAGE 86
PCISA-9652 Half-Size CPU Card Figure 4-21: 14-Pin Serial Port Connector Locations PIN NO. DESCRIPTION PIN NO. DESCRIPTION 1 DCD 2 DSR 3 RXD 4 RTS 5 TXD 6 CTS 7 DTR 8 RI 9 GND 10 GND 11 TXD 485+ 12 TXD 485# 13 RXD 485+ 14 RXD 485# Table 4-21: COM 2 Pinouts 4.2.20 TV Out Connector CN Label: TV1 CN Type: 6-pin header (2x3) CN Location: See Figure 4-22 CN Pinouts: See Table 4-22 The 2x3 pin TV out connector connects to a TV output by using an S-Video or RCA connector.
PAGE 87
PCISA -9652 Half-Size CPU Card Figure 4-22: TV Connector Pinout Locations S-Video Connector PIN NO. DESCRIPTION PIN NO. DESCRIPTION 1 GND 2 AGREEN_Y 3 GND 4 ARED_C RCA Connector (only video signal) 5 GND 6 ABLUE_CVBS Table 4-22: TV Port Connector Pinouts 4.2.21 Internal USB Connectors CN Label: USB01 and USB23 CN Type: 8-pin header (2x4) CN Location: See Figure 4-23 CN Pinouts: See Table 4-23 One 2x4 pin connector provides connectivity to two USB 2.0 ports.
PAGE 88
PCISA-9652 Half-Size CPU Card Figure 4-23: Internal USB Connector Locations PIN NO. DESCRIPTION PIN NO.
PAGE 89
PCISA -9652 Half-Size CPU Card 4.3 External Interface Connectors The peripheral connectors on the back panel are connected to devices externally when the PCISA-9652 is installed in a chassis. The peripheral connectors on the rear panel are: 1 x CRT connector 2 x RJ-45 Ethernet connectors 2 x USB 2.0 connectors Figure 4-24: PCISA-9652 External Interface Connectors 4.3.
PAGE 90
PCISA-9652 Half-Size CPU Card PIN NO. DESCRIPTION PIN NO. DESCRIPTION 1 RED 2 GREEN 3 BLUE 4 N/C 5 GND 6 GND 7 GND 8 GND 9 VCC 10 GND 11 N/C 12 DDC DAT 13 HSYNC 14 VSYNC 15 DDC CLK Table 4-24: VGA Connector Pinouts 4.3.2 Ethernet Connectors CN Label: LAN1 and LAN2 CN Type: RJ-45 CN Location: See Figure 4-24 CN Pinouts: See Table 4-25 The PCISA-9652 is equipped with two built-in GbE Ethernet controllers.
PAGE 91
PCISA -9652 Half-Size CPU Card Figure 4-26: RJ-45 Ethernet Connector The RJ-45 Ethernet connector has two status LEDs, one green and one yellow. The green LED indicates activity on the port and the yellow LED indicates the port is linked. See Table 4-26. SPEED LED STATUS ACT/LINK LED DESCRIPTION STATUS DESCRIPTION OFF 10Mbps connection OFF No link ORANGE 100Mbps connection YELLOW Linked GREEN 1Gbps connection BLINKING Data Activity Table 4-26: RJ-45 Ethernet Connector LEDs 4.3.
PAGE 92
PCISA-9652 Half-Size CPU Card THIS PAGE IS INTENTIONALLY LEFT BLANK Page 72
PAGE 93
PCISA -9652 Half-Size CPU Card Chapter 5 5 Installation Page 73
PAGE 94
PCISA-9652 Half-Size CPU Card 5.1 Anti-static Precautions WARNING: Failure to take ESD precautions during the installation of the PCISA-9652 may result in permanent damage to the PCISA-9652 and severe injury to the user. Electrostatic discharge (ESD) can cause serious damage to electronic components, including the PCISA-9652. Dry climates are especially susceptible to ESD.
PAGE 95
PCISA -9652 Half-Size CPU Card 5.2 Installation Considerations NOTE: The following installation notices and installation considerations should be read and understood before the PCISA-9652 is installed. All installation notices pertaining to the installation of the PCISA-9652 should be strictly adhered to. Failing to adhere to these precautions may lead to severe damage of the PCISA-9652 and injury to the person installing the motherboard. 5.2.
PAGE 96
PCISA-9652 Half-Size CPU Card o When working with the PCISA-9652, make sure that it is disconnected from all power supplies and that no electricity is being fed into the system. Before and during the installation of the PCISA-9652 DO NOT: Remove any of the stickers on the PCB board. These stickers are required for warranty validation. Use the product before verifying all the cables and power connectors are properly connected.
PAGE 97
PCISA -9652 Half-Size CPU Card 5.3 CPU, CPU Cooling Kit and DIMM Installation WARNING: A CPU should never be turned on without the specified cooling kit being installed. If the cooling kit (heat sink and fan) is not properly installed and the system turned on, permanent damage to the CPU, PCISA-9652 and other electronic components attached to the system may be incurred. Running a CPU without a cooling kit may also result in injury to the user.
PAGE 98
PCISA-9652 Half-Size CPU Card CPU socket should be in the unlocked position. If it is not in the unlocked position, use a screwdriver to unlock the screw. See Figure 5-1. Figure 5-1: Make sure the CPU socket retention screw is unlocked Step 2: Inspect the CPU socket. Make sure there are no bent pins and make sure the socket contacts are free of foreign material. If any debris is found, remove it with compressed air. Step 3: Correctly Orientate the CPU.
PAGE 99
PCISA -9652 Half-Size CPU Card Figure 5-2: Lock the CPU Socket Retention Screw 5.3.2 Cooling Kit CF-479B-RS Installation Figure 5-3: IEI CF-479B-RS Cooling Kit An IEI Socket P CPU cooling kit can be purchased separately. The cooling kit comprises a CPU heat sink and a cooling fan.
PAGE 100
PCISA-9652 Half-Size CPU Card WARNING: Do not wipe off (accidentally or otherwise) the pre-sprayed layer of thermal paste on the bottom of the CF-479B-RS heat sink. The thermal paste between the CPU and the heat sink is important for optimum heat dissipation. To install the CF-479B-RS cooling kit, please follow the steps below. Step 1: Place the cooling kit onto the CPU. Make sure the CPU cooling fan cable can be properly routed when the cooling kit is installed. Step 2: Properly align the cooling kit.
PAGE 101
PCISA -9652 Half-Size CPU Card Step 5: Connect the fan cable. Connect the cooling kit fan cable to the fan connector on the motherboard. Carefully route the cable and avoid heat generating chips and fan blades. See Figure 5-5. Step 0: Figure 5-5: Connect the cooling fan cable 5.3.3 DIMM Installation WARNING: Only DDR2 memory module can be installed on the PCISA-9652. Do not install DDR memory modules. If a DDR memory module is installed on the PCISA-9652, the PCISA-9652 may be irreparably damaged.
PAGE 102
PCISA-9652 Half-Size CPU Card CAUTION: The DIMM1 socket must be installed with one DDR2 DIMM to enable the PCISA-9652 to boot-up properly. To install a DIMM into a DIMM socket, please follow the steps below and refer to Figure 5-6. Figure 5-6: Installing a DIMM Step 1: Open the DIMM socket handles. The DIMM socket has two handles that secure the DIMM into the socket. Before the DIMM can be inserted into the socket, the handles must be opened. See Figure 5-6. Step 2: Align the DIMM with the socket.
PAGE 103
PCISA -9652 Half-Size CPU Card close automatically and secure the DIMM to the socket. See Figure 5-6. Step 4: Removing a DIMM. To remove a DIMM, push both handles outward. The memory module is ejected by a mechanism in the socket.Step 0: 5.4 Jumper Settings NOTE: A jumper is a metal bridge used to close an electrical circuit. It consists of two or three metal pins and a small metal clip (often protected by a plastic cover) that slides over the pins to connect them.
PAGE 104
PCISA-9652 Half-Size CPU Card 5.4.1 CF Card Setup Jumper Label: JCF1 Jumper Type: 2-pin header Jumper Settings: See Table 5-2 Jumper Location: See Figure 5-8 The CF Card Setup jumper sets the CF Type I card or CF Type II cards as either the slave device or the master device. CF Card Setup jumper settings are shown in Table 5-2. CF Card Setup Description Open Slave Closed Master Default Table 5-2: CF Card Setup Jumper Settings The CF Card Setup jumper location is shown in Figure 5-8.
PAGE 105
PCISA -9652 Half-Size CPU Card 5.4.2 Clear CMOS Jumper Jumper Label: J_COMS1 Jumper Type: 3-pin header Jumper Settings: See Table 5-3 Jumper Location: See Figure 5-9 If the PCISA-9652 fails to boot due to improper BIOS settings, the clear CMOS jumper clears the CMOS data and resets the system BIOS information. To do this, use the jumper cap to close pins 2 and 3 for a few seconds then reinstall the jumper clip back to pins 1 and 2.
PAGE 106
PCISA-9652 Half-Size CPU Card Figure 5-9: Clear CMOS Jumper 5.4.3 COM 2 Function Select Jumper Jumper Label: JP2 Jumper Type: 6-pin header Jumper Settings: See Table 5-4 Jumper Location: See Figure 5-10 The COM 2 Function Select jumper sets the communication protocol used by the second serial communications port (COM 2) as RS-232, RS-422 or RS-485. The COM 2 Function Select settings are shown in Figure 5-10.
PAGE 107
PCISA -9652 Half-Size CPU Card Figure 5-10: COM 2 Function Select Jumper Location 5.4.4 LVDS Voltage Selection WARNING: Permanent damage to the screen and PCISA-9652 may occur if the wrong voltage is selected with this jumper. Please refer to the user guide that cam with the monitor to select the correct voltage.
PAGE 108
PCISA-9652 Half-Size CPU Card LVDS Voltage Select Description Short 1-2 +3V Short 2-3 +5V Default Table 5-5: LVDS Voltage Selection Jumper Settings The LVDS Voltage Selection jumper location is shown in Figure 5-11. Figure 5-11: LVDS Voltage Selection Jumper Pinout Locations 5.4.
PAGE 109
PCISA -9652 Half-Size CPU Card Short 1-2 & 3-4 1024 x 768 (24-bit) Short 5-6 1024 x 768 (48-bit) Short 1-2 & 5-6 1280 x 1024 (48-bit) Short 3-4 & 5-6 1600 x 1200 (48-bit) Short 1-2 & 3-4 & 5-6 1280 x 768 (18-bit) Short 7-8 1280 x 800 (18-bit) Short 1-2 & 7-8 1366 x 768 (24-bit) Short 3-4 & 7-8 1440 x 900 (36-bit) Short 1-2 & 3-4 & 7-8 1440 x 900 (48-bit) Short 5-6 & 7-8 1680 X 1050 (48-bit) Short 1-2 & 5-6 & 7-8 1920 X 1080 (48-bit) Short 3-4 & 5-6 & 7-8 1920 X 1200 (48-bit) Table 5-
PAGE 110
PCISA-9652 Half-Size CPU Card 5.5 Chassis Installation 5.5.1 Airflow WARNING: Airflow is critical to the cooling of the CPU and other onboard components. The chassis in which the PCISA-9652 must have air vents to allow cool air to move into the system and hot air to move out. The PCISA-9652 must be installed in a chassis with ventilation holes on the sides allowing airflow to travel through the heat sink surface.
PAGE 111
PCISA -9652 Half-Size CPU Card NOTE: IEI has a wide range of backplanes available. Please contact your PCISA-9652 vendor, reseller or an IEI sales representative at sales@iei.com.tw or visit the IEI website (http://www.ieiworld.com.tw) to find out more about the available chassis. 5.5.3 CPU Card Installation To install the PCISA-9652 CPU card onto the backplane, carefully align the CPU card interface connectors with the corresponding socket on the backplane.
PAGE 112
PCISA-9652 Half-Size CPU Card HDTV/TV cable with S-Video/Composite/Component output 5.6.2 IDE Cable Connection The IDE flat cable connects to the PCISA-9652 to one or two IDE devices. To connect an IDE HDD to the PCISA-9652, please follow the instructions below. Step 1: Locate the IDE connector. The location of the IDE device connector is shown in Chapter 3. Step 2: Insert the connector. Connect the IDE cable connector to the onboard connector. See Figure 5-13.
PAGE 113
PCISA -9652 Half-Size CPU Card The PCISA-9652 is shipped with two SATA drive cables and one SATA drive power cable. To connect the SATA drives to the connectors, please follow the steps below. Step 1: Locate the connectors. The locations of the SATA drive connectors are shown in Chapter 3. Step 2: Insert the cable connector. Press the clip on the connector at the end of the SATA cable and insert the cable connector into the onboard SATA drive connector. See Figure 5-14.
PAGE 114
PCISA-9652 Half-Size CPU Card Figure 5-15: SATA Power Drive Connection 5.6.4 USB Cable (Dual Port) with Slot Bracket The PCISA-9653 can be shipped with a dual port USB 2.0 cable. To connect the USB cable connector, please follow the steps below. Step 1: Locate the connectors. The locations of the USB connectors are shown in Chapter 3. WARNING: If the USB pins are not properly aligned, the USB device can burn out. Step 2: Align the connectors. The cable has two connectors.
PAGE 115
PCISA -9652 Half-Size CPU Card the onboard connectors. See Figure 5-16. Figure 5-16: Dual USB Cable Connection Step 4: Attach the bracket to the chassis. The USB 2.0 connectors are attached to a bracket. To secure the bracket to the chassis please refer to the installation instructions that came with the chassis.Step 0: 5.6.5 7.1 Channel Audio Kit Installation (Optional) NOTE: This is an optional item that must be ordered separately.
PAGE 116
PCISA-9652 Half-Size CPU Card Center Subwoofer, connect to speakers. To install the audio kit, please refer to the steps below: Step 1: Connect the audio kit cable. The audio kit is shipped with a cable that connects the audio kit to the PCISA-9652. Connect the cable to the connector on the back of the audio kit. Make sure the pins are properly aligned (i.e. pin 1 connects to pin 1). Step 2: Locate the audio connector. The location of the 10-pin audio connector is shown in Chapter 3. Step 3: Align pin 1.
PAGE 117
PCISA -9652 Half-Size CPU Card Step 6: Install the driver. If the 7.1 channel audio kit is used, the ALC883 Realtek codec driver must be installed. Refer to Chapter 7 for driver installation instructions.Step 0: 5.7 External Peripheral Interface Connection The following external peripheral devices can be connected to the external peripheral interface connectors.
PAGE 118
PCISA-9652 Half-Size CPU Card Figure 5-18: LAN Connection Step 3: Insert the LAN cable RJ-45 connector. Once aligned, gently insert the LAN cable RJ-45 connector into the on-board RJ-45 connector. Step 0: 5.7.2 VGA Monitor Connection The PCISA-9652 has a single female DB-15 connector on the external peripheral interface panel. The DB-15 connector is connected to a CRT or VGA monitor. To connect a monitor to the PCISA-9652, please follow the instructions below. Step 1: Locate the female DB-15 connector.
PAGE 119
PCISA -9652 Half-Size CPU Card Figure 5-19: VGA Connector Step 4: Secure the connector. Secure the DB-15 VGA connector from the VGA monitor to the external interface by tightening the two retention screws on either side of the connector. Step 0: 5.7.3 USB Device Connection (Single Connector) There are two external USB 2.0 connectors. Both connectors are perpendicular to the PCISA-9652. To connect a USB 2.0 or USB 1.1 device, please follow the instructions below. Step 1: Located the USB connectors.
PAGE 120
PCISA-9652 Half-Size CPU Card Figure 5-20: USB Device Connection Step 3: Insert the device connector. Once aligned, gently insert the USB device connector into the on-board connector.
PAGE 121
PCISA -9652 Half-Size CPU Card Chapter 6 6 AMI BIOS Page 101
PAGE 122
PCISA-9652 Half-Size CPU Card 6.1 Introduction A licensed copy of AMI BIOS is preprogrammed into the ROM BIOS. The BIOS setup program allows users to modify the basic system configuration. This chapter describes how to access the BIOS setup program and the configuration options that may be changed. 6.1.1 Starting Setup The AMI BIOS is activated when the computer is turned on. The setup program can be activated in one of two ways. 1. Press the DELETE key as soon as the system is turned on or 2.
PAGE 123
PCISA -9652 Half-Size CPU Card F1 key General help, only for Status Page Setup Menu and Option Page Setup Menu F2 /F3 key Change color from total 16 colors. F2 to select color forward. F10 key Save all the CMOS changes, only for Main Menu Table 6-1: BIOS Navigation Keys 6.1.3 Getting Help When F1 is pressed a small help window describing the appropriate keys to use and the possible selections for the highlighted item appears. To exit the Help Window press ESC or the F1 key again. 6.1.
PAGE 124
PCISA-9652 Half-Size CPU Card 6.2 Main The Main BIOS menu (BIOS Menu 1) appears when the BIOS Setup program is entered. The Main menu gives an overview of the basic system information. BIOS Menu 1: Main System Overview The System Overview lists a brief summary of different system components. The fields in System Overview cannot be changed.
PAGE 125
PCISA -9652 Half-Size CPU Card o Count: The number of CPUs on the motherboard System Memory: Displays the auto-detected system memory. o Size: Lists memory size The System Overview field also has two user configurable fields: System Time [xx:xx:xx] Use the System Time option to set the system time. Manually enter the hours, minutes and seconds. System Date [xx/xx/xx] Use the System Date option to set the system date. Manually enter the day, month and year. 6.
PAGE 126
PCISA-9652 Half-Size CPU Card BIOS Menu 2: Advanced 6.3.1 CPU Configuration Use the CPU Configuration menu (BIOS Menu 3) to view detailed CPU specifications and configure the CPU.
PAGE 127
PCISA -9652 Half-Size CPU Card BIOS Menu 3: CPU Configuration The CPU Configuration menu (BIOS Menu 3) lists the following CPU details: Manufacturer: Lists the name of the CPU manufacturer Brand String: Lists the brand name of the CPU being used Frequency: Lists the CPU processing speed FSB Speed: Lists the FSB speed Cache L1: Lists the CPU L1 cache size Cache L2: Lists the CPU L2 cache size 6.3.
PAGE 128
PCISA-9652 Half-Size CPU Card BIOS Menu 4: IDE Configuration ATA/IDE Configurations [Compatible] Use the ATA/IDE Configurations option to configure the ATA/IDE controller. Disables the on-board ATA/IDE controller. Disabled Compatible DEFAULT Configures the on-board ATA/IDE controller to be in compatible mode. In this mode, a SATA channel will replace one of the IDE channels. This mode supports up to 4 storage devices. Enhanced Configures the on-board ATA/IDE controller to be in Enhanced mode.
PAGE 129
PCISA -9652 Half-Size CPU Card Legacy IDE Channels [SATA Pri, PATA Sec] SATA Only SATA Pri., PATA Sec DEFAULT PATA Only IDE Master and IDE Slave When entering setup, BIOS auto detects the presence of IDE devices. BIOS displays the status of the auto detected IDE devices.
PAGE 130
PCISA-9652 Half-Size CPU Card BIOS Menu 5: IDE Master and IDE Slave Configuration Type [Auto] Use the Type BIOS option select the type of device the AMIBIOS attempts to boot from after the Power-On Self-Test (POST) is complete. BIOS is prevented from searching for an IDE disk Not Installed drive on the specified channel. Auto DEFAULT The BIOS auto detects the IDE disk drive type attached to the specified channel.
PAGE 131
PCISA -9652 Half-Size CPU Card IDE disk drives on the specified channel. This option specifies an ATAPI Removable Media ARMD Device. These include, but are not limited to: ZIP LS-120 LBA/Large Mode [Auto] Use the LBA/Large Mode option to disable or enable BIOS to auto detects LBA (Logical Block Addressing). LBA is a method of addressing data on a disk drive. In LBA mode, the maximum drive capacity is 137 GB. BIOS is prevented from using the LBA mode control on Disabled the specified channel.
PAGE 132
PCISA-9652 Half-Size CPU Card PIO Mode [Auto] Use the PIO Mode option to select the IDE PIO (Programmable I/O) mode program timing cycles between the IDE drive and the programmable IDE controller. As the PIO mode increases, the cycle time decreases. Auto DEFAULT BIOS auto detects the PIO mode. Use this value if the IDE disk drive support cannot be determined. 0 PIO mode 0 selected with a maximum transfer rate of 3.3MBps 1 PIO mode 1 selected with a maximum transfer rate of 5.
PAGE 133
PCISA -9652 Half-Size CPU Card MWDMA0 Multi Word DMA mode 0 selected with a maximum data transfer rate of 4.2MBps MWDMA1 Multi Word DMA mode 1 selected with a maximum data transfer rate of 13.3MBps MWDMA2 Multi Word DMA mode 2 selected with a maximum data transfer rate of 16.6MBps UDMA1 Ultra DMA mode 0 selected with a maximum data transfer rate of 16.
PAGE 134
PCISA-9652 Half-Size CPU Card Auto DEFAULT BIOS auto detects HDD SMART support. Disabled Prevents BIOS from using the HDD SMART feature. Enabled Allows BIOS to use the HDD SMART feature 32Bit Data Transfer [Enabled] Use the 32Bit Data Transfer BIOS option to enables or disable 32-bit data transfers. Prevents the BIOS from using 32-bit data transfers. Disabled Enabled DEFAULT Allows BIOS to use 32-bit data transfers on supported hard disk drives. 6.3.
PAGE 135
PCISA -9652 Half-Size CPU Card Floppy A Use the Floppy A option to configure the floppy disk drive. Options are listed below: Disabled 360 KB 51/4” 1.2 MB 51/4” 720 KB 31/2” 1.44 MB 31/2’ 2.88 MB 31/2” 6.3.4 Super IO Configuration Use the Super IO Configuration menu (BIOS Menu 7) to set or change the configurations for the FDD controllers, parallel ports and serial ports.
PAGE 136
PCISA-9652 Half-Size CPU Card Serial Port1 Address [3F8/IRQ4] Use the Serial Port1 Address option to select the Serial Port 1 base address.
PAGE 137
PCISA -9652 Half-Size CPU Card Serial Port 2 I/O port address is 2E8 and the interrupt 2E8/IRQ3 address is IRQ3 Serial Port2 Mode [Normal] Use the Serial Port2 Mode option to select the Serial Port2 operational mode. Normal Serial Port 2 mode is normal DEFAULT IrDA Serial Port 2 mode is IrDA ASK IR Serial Port 2 mode is ASK IR Parallel Port Address [378] Use the Parallel Port Address option to select the parallel port base address.
PAGE 138
PCISA-9652 Half-Size CPU Card Normal mode. The ECP parallel port operates in the extended capabilities port (ECP) mode. The ECP mode supports bi-directional communication between the system and the parallel port device and the transmission rates between the two are much faster than the Normal mode EPP+ECP The parallel port is compatible with both EPP and ECP devices described above Parallel Port IRQ [IRQ7] Use the Parallel Port IRQ selection to set the parallel port interrupt address.
PAGE 139
PCISA -9652 Half-Size CPU Card BIOS Menu 8: Hardware Health Configuration The following system parameters and values are shown. The system parameters that are monitored are: System Temperatures: The following system temperatures are monitored o o o CPU Temperature PWM Temperature System Temperature Fan Speeds: The CPU cooling fan speed is monitored. o Fan1 Speed Voltages: The following system voltages are monitored o o o o o CPU Core +1.8V +3.30V +5.00V +12.
PAGE 140
PCISA-9652 Half-Size CPU Card o o o o +1.05V +1.5V +1.25V VBAT 6.3.6 Remote Access Configuration Use the Remote Access Configuration menu (BIOS Menu 9) to configure remote access parameters. The Remote Access Configuration is an AMIBIOS feature and allows a remote host running a terminal program to display and configure the BIOS settings.
PAGE 141
PCISA -9652 Half-Size CPU Card Disabled DEFAULT Remote access is disabled. Remote access configuration options shown below Enabled appear: Serial Port Number Serial Port Mode Redirection after BIOS POST Terminal Type These configuration options are discussed below. Serial Port Number [COM1] Use the Serial Port Number option allows users to select the serial port used for remote access.
PAGE 142
PCISA-9652 Half-Size CPU Card 38400 8,n,1 19200 8,n,1 09600 8,n,1 NOTE: Identical baud rate setting musts be set on the host (a management computer running a terminal software) and the slave Redirection After BIOS POST [Always] Use the Redirection After BIOS POST option to specify when console redirection should occur.
PAGE 143
PCISA -9652 Half-Size CPU Card BIOS Menu 10: USB Configuration USB Configuration The USB Configuration field shows the system USB configuration. The items listed are: Module Version: x.xxxxx.xxxxx USB Devices Enabled The USB Devices Enabled field lists the USB devices that are enabled on the system USB Function [Enabled] Use the USB Function BIOS option to enable or disable the USB function.
PAGE 144
PCISA-9652 Half-Size CPU Card Legacy USB Support [Enabled] Use the Legacy USB Support BIOS option to enable USB mouse and USB keyboard support. Normally if this option is not enabled, any attached USB mouse or USB keyboard does not become available until a USB compatible operating system is fully booted with all USB drivers loaded. When this option is enabled, any attached USB mouse or USB keyboard can control the system even when there is no USB driver loaded onto the system.
PAGE 145
PCISA -9652 Half-Size CPU Card 6.3.7.1 USB Mass Storage Device Configuration Use the USB Mass Storage Device Configuration menu (BIOS Menu 11) to configure USB mass storage class devices. BIOS Menu 11: USB Mass Storage Device Configuration USB Mass Storage Reset Delay [20 Sec] Use the USB Mass Storage Reset Delay option to set the number of seconds POST waits for the USB mass storage device after the start unit command.
PAGE 146
PCISA-9652 Half-Size CPU Card device after the start unit command. POST waits 40 seconds for the USB mass storage 40 Sec device after the start unit command. Device ## The Device## field lists the USB devices that are connected to the system. Emulation Type [Auto] Use the Emulation Type BIOS option to specify the type of emulation BIOS has to provide for the USB device.
PAGE 147
PCISA -9652 Half-Size CPU Card floppy image. This option works only for drives formatted with FAT12, FAT16 or FAT32. Hard Disk Allows the USB device to be emulated as hard disk responding to INT13h calls that return DL values of 80h or above. CDROM Assumes the CD-ROM is formatted as bootable media. All the devices that support block sizes greater than 512 bytes can only be booted using this option. 6.3.
PAGE 148
PCISA-9652 Half-Size CPU Card Power Supply Mode [ATX] Use the Power Supply Mode BIOS option to select the power supply that is connected to the system. AT An AT power supply is connected to the system ATX An ATX power supply is connected to the system BY HARDWARE DEFAULT The power supply mode is depends on hardware 6.4 PCI/PnP Use the PCI/PnP menu (BIOS Menu 13) to configure advanced PCI and PnP settings.
PAGE 149
PCISA -9652 Half-Size CPU Card IRQ# Use the IRQ# address to specify what IRQs can be assigned to a particular peripheral device. The specified IRQ is available to be used by Available PCI/PnP devices The specified IRQ is reserved for use by Legacy ISA Reserved devices Available IRQ addresses options are: IRQ3 IRQ4 IRQ5 IRQ7 IRQ9 IRQ10 IRQ 11 IRQ 14 IRQ 15 DMA Channel# [Available] Use the DMA Channel# option to assign a specific DMA channel to a particular PCI/PnP device.
PAGE 150
PCISA-9652 Half-Size CPU Card DM Channel 1 DM Channel 3 DM Channel 5 DM Channel 6 DM Channel 7 Reserved Memory Size [Disabled] Use the Reserved Memory Size BIOS option to specify the amount of memory that should be reserved for legacy ISA devices. Disabled DEFAULT No memory block reserved for legacy ISA devices 16K 16KB reserved for legacy ISA devices 32K 32KB reserved for legacy ISA devices 64K 54KB reserved for legacy ISA devices 6.
PAGE 151
PCISA -9652 Half-Size CPU Card BIOS Menu 14: Boot 6.5.1 Boot Settings Configuration Use the Boot Settings Configuration menu (BIOS Menu 15) to configure advanced system boot options.
PAGE 152
PCISA-9652 Half-Size CPU Card BIOS Menu 15: Boot Settings Configuration Quick Boot [Enabled] Use the Quick Boot BIOS option to make the computer speed up the boot process. No POST procedures are skipped Disabled Enabled DEFAULT Some POST procedures are skipped to decrease the system boot time Quiet Boot [Enabled] Use the Quiet Boot BIOS option to select the screen display when the system boots.
PAGE 153
PCISA -9652 Half-Size CPU Card Use the AddOn ROM Display Mode option to allow add-on ROM (read-only memory) messages to be displayed. Force BIOS DEFAULT The system forces third party BIOS to display during system boot. The system displays normal information during Keep Current system boot. Bootup Num-Lock [On] Use the Bootup Num-Lock BIOS option to specify if the number lock setting must be modified during boot up. Does not enable the keyboard Number Lock automatically.
PAGE 154
PCISA-9652 Half-Size CPU Card Enabled Can be booted from a remote system through the Intel® 82573L PCIe GbE controller 6.5.2 Boot Device Priority Use the Boot Device Priority menu (BIOS Menu 16) to specify the boot sequence from the available devices. Possible boot devices may include: USB HDD CD/DVD BIOS Menu 16: Boot Device Priority Settings 6.5.3 Removable Drives Use the Removable Drives menu (BIOS Menu 17) to specify the boot sequence of the available USB devices.
PAGE 155
PCISA -9652 Half-Size CPU Card 1st Drive [1st USB] 2nd Drive [2nd USB] NOTE: Only the drives connected to the system are shown. For example, if only one USB device is connected only “1st Drive” is listed. The boot sequence from the available devices is selected. If the “1st Drive” option is selected a list of available USB devices is shown. Select the first USB device the system boots from. If the “1st Drive” is not used for booting this option may be disabled. BIOS Menu 17: Removable Drives 6.
PAGE 156
PCISA-9652 Half-Size CPU Card BIOS Menu 18: Security Change Supervisor Password Use the Change Supervisor Password to set or change a supervisor password. The default for this option is Not Installed. If a supervisor password must be installed, select this field and enter the password. After the password has been added, Install appears next to Change Supervisor Password. Change User Password Use the Change User Password to set or change a user password. The default for this option is Not Installed.
PAGE 157
PCISA -9652 Half-Size CPU Card Use the Chipset menu to access the NorthBridge, SouthBridge and ME Subsystem configuration menus. WARNING! Setting the wrong values for the Chipset BIOS selections in the Chipset BIOS menu may cause the system to malfunction. 6.7.1 NorthBridge Configuration Use the Northbridge Chipset Configuration menu (BIOS Menu 19) to configure the Northbridge chipset.
PAGE 158
PCISA-9652 Half-Size CPU Card Overlapped PCI memory cannot be remapped Disabled Enabled DEFAULT Overlapped PCI memory can be remapped Memory Hole [Disabled] Use the Memory Hole option to reserve memory space between 15MB and 16MB for ISA expansion cards that require a specified area of memory to work properly. If an older ISA expansion card is used, please refer to the documentation that came with the card to see if it is necessary to reserve the space.
PAGE 159
PCISA -9652 Half-Size CPU Card 6.7.1.1 Video Function Configuration Use the Video Function Configuration menu to configure the video device connected to the system. Boot Display Device [Auto] Use the Boot Display Device option to select the display device used by the system when it boots. Configuration options are listed below. Auto DEFAULT CRT TV LFP Flat Panel Type [BY HARDWARE] Use the Flat Panel Type option to select the type of flat panel connected to the system.
PAGE 160
PCISA-9652 Half-Size CPU Card SMPTE240M ITU-R television SMPTE295M SMPTE296M EIA-770.2 EIA-770.3 6.7.2 Southbridge Configuration The Southbridge Configuration menu (BIOS Menu 20) allows the Southbridge chipset to be configured. BIOS Menu 20:Southbridge Chipset Configuration HDA Controller [Enabled] Use the HDA Controller option to enable the Southbridge high definition audio controller. If the HDA device has been connected to the system, this option should be enabled.
PAGE 161
PCISA -9652 Half-Size CPU Card Disabled Southbridge HDA controller is disabled 6.8 Exit Use the Exit menu (BIOS Menu 21) to load default BIOS values, optimal failsafe values and to save configuration changes. BIOS Menu 21: Exit Save Changes and Exit Use the Save Changes and Exit option to save the changes made to the BIOS options and to exit the BIOS configuration setup program.
PAGE 162
PCISA-9652 Half-Size CPU Card Discard Changes Use the Discard Changes option to discard the changes and remain in the BIOS configuration setup program. Load Optimal Defaults Use the Load Optimal Defaults option to load the optimal default values for each of the parameters on the Setup menus. F9 key can be used for this operation. Load Failsafe Defaults Use the Load Failsafe Defaults option to load failsafe default values for each of the parameters on the Setup menus. F8 key can be used for this operation.
PAGE 163
PCISA -9652 Half-Size CPU Card Chapter 7 7 Software Drivers Page 143
PAGE 164
PCISA-9652 Half-Size CPU Card 7.1 Available Software Drivers NOTE: The content of the CD may vary throughout the life cycle of the product and is subject to change without prior notice. Visit the IEI website or contact technical support for the latest updates. The following drivers can be installed on the system: Intel® chipset driver VGA driver LAN drivers Audio driver SATA driver Installation instructions are given below. 7.
PAGE 165
PCISA -9652 Half-Size CPU Card Figure 7-1: Introduction Screen Step 3: Click PCISA-9652. Step 4: A new screen with a list of available drivers appears (Figure 7-2). Figure 7-2: Available Drivers Step 5: Select the driver to install from the list in Figure 7-2. Detailed driver installation instructions follow below.
PAGE 166
PCISA-9652 Half-Size CPU Card 7.3 Intel® Chipset Driver To install the Intel® chipset driver, please follow the steps below. Step 1: Select PCISA-9652 from the list in Figure 7-1. Step 2: Select INF from the list in Figure 7-2. Step 3: The window shown in Figure 7-3 appears. Figure 7-3: Intel® Chipset Driver Directory Step 4: Click on the directory icon in Figure 7-3. Step 5: The window in Figure 7-4 appears.
PAGE 167
PCISA -9652 Half-Size CPU Card Figure 7-4: Intel® Chipset Driver Setup Icon Step 6: Click on the infinst_autol setup icon in Figure 7-4. Step 7: The Intel® Package Manager begins to extract the installation files. See Figure 7-5.
PAGE 168
PCISA-9652 Half-Size CPU Card Figure 7-5: Intel® Package Manager Step 8: The Intel® Setup Welcome screen. See Figure 7-6. Figure 7-6: Intel® Setup Welcome Screen Step 9: Click NEXT to continue. Step 10: The Intel® license agreement in appears.
PAGE 169
PCISA -9652 Half-Size CPU Card Figure 7-7: Intel® Chipset Driver License Agreement Step 11: Accept the terms and conditions by clicking YES. Step 12: The Readme file in Figure 7-8 appears. Figure 7-8: Readme File Step 13: Click NEXT to continue.
PAGE 170
PCISA-9652 Half-Size CPU Card Step 14: The driver is then installed. Step 15: When the installation process is complete, the Setup Complete screen appears. See Figure 7-9. Figure 7-9: Intel® Chipset Driver Complete Installation Screen Step 16: To complete the chipset driver installation, click FINISH. Step 0: 7.4 Intel® Graphics Media Accelerator Driver To install the chipset driver, please follow the steps below: Step 1: Select the VGA driver from the list in Figure 7-2. Step 2: A new window opens.
PAGE 171
PCISA -9652 Half-Size CPU Card Figure 7-10: Select the Operating System Step 3: Select the operating system from those shown in Figure 7-10. Step 4: A new window appears. See Figure 7-11.
PAGE 172
PCISA-9652 Half-Size CPU Card Step 5: Click the directory icon in Figure 7-11. Step 6: A new window appears. See Figure 7-12. Figure 7-12: Intel® VGA Driver Setup Icon Step 7: Click on the VGA driver installation icon in See Figure 7-12. Step 8: The Readme information file shown in Figure 7-13 appears.
PAGE 173
PCISA -9652 Half-Size CPU Card Figure 7-13: GMA Driver Readme File Step 9: Click NEXT to extract the GMA driver files. See Figure 7-14. Figure 7-14: GMA Driver File Extraction Step 10: The welcome screen shown in Figure 7-15 appears.
PAGE 174
PCISA-9652 Half-Size CPU Card Figure 7-15: GMA Driver Installation Welcome Screen Step 11: To continue the installation process, click NEXT. Step 12: The license agreement in Figure 7-16 appears. Figure 7-16: GMA Driver License Agreement Step 13: Click the YES in Figure 7-16 to continue.
PAGE 175
PCISA -9652 Half-Size CPU Card Step 14: The installation notice shown in Figure 7-17 appears. Figure 7-17: GMA Driver Installing Notice Step 15: A confirmation screen shown in Figure 7-18 appears. Figure 7-18: GMA Driver Installation Complete Step 16: After selecting when to restart the computer in Figure 7-18, click FINISH. Step 0: 7.5 Intel® 82573 PCI Express Gigabit Ethernet Controller Driver To install the Intel® 82573 PCIe GbE controller, please follow the steps below.
PAGE 176
PCISA-9652 Half-Size CPU Card Figure 7-19: Intel® 82573 Driver Directory Icon Step 3: Click on the Intel® 82573L directory icon in Figure 7-19. Step 4: The window in Figure 7-20 appears.
PAGE 177
PCISA -9652 Half-Size CPU Card Step 5: Select the Operating System in Figure 7-20. Step 6: The window in Figure 7-21 appears. Step 7: In Figure 7-21 select the operating system type installed on the system. Figure 7-21: Select Operating System Type Step 8: The window in Figure 7-22 appears.
PAGE 178
PCISA-9652 Half-Size CPU Card Step 9: Click on the directory icon in Figure 7-22. Step 10: A window containing the Intel® 82573 driver startup icon appears. See Figure 7-22. Figure 7-23: Intel® 82573 Driver Startup Icon Step 11: Click the startup icon in Figure 7-23. Step 12: The License Agreement for the Intel® 82573 appears. See Figure 7-24.
PAGE 179
PCISA -9652 Half-Size CPU Card Figure 7-24: Intel® 82573 License Agreement Step 13: Accept the license terms and agreements in and click NEXT to continue. Step 14: Next, select the directory in which the files must be saved. See Figure 7-25. Figure 7-25: Intel® 82573 File Location Select Step 15: Click NEXT to continue.
PAGE 180
PCISA-9652 Half-Size CPU Card Step 16: The driver begins to extract the installation files. See Figure 7-26. Figure 7-26: Intel® 82573 Installation Files Extraction Step 17: The Intel® PRO Network Connections window appears. See Figure 7-27. Figure 7-27: Intel® PRO Network Connections window Step 18: Click INSTALL DRIVERS in Figure 7-27.
PAGE 181
PCISA -9652 Half-Size CPU Card Step 19: The Intel® PRO Network Connections Welcome screen in Figure 7-28 appears. Figure 7-28: Intel® PRO Network Connections Welcome Step 20: Click NEXT to continue. Step 21: A new License Agreement appears. See Figure 7-29. Figure 7-29: License Agreement Step 22: Accept the terms and conditions in Figure 7-29 and click NEXT to continue.
PAGE 182
PCISA-9652 Half-Size CPU Card Step 23: The Setup Type window in Figure 7-30 appears. Figure 7-30: Setup Type Step 24: Select the setup type in Figure 7-30 and click NEXT to continue. Step 25: The drivers are installed. See Figure 7-31. Figure 7-31: Intel® 82573 Driver Installation Progress Step 26: When the driver is installed. Click FINISH in the termination screen.
PAGE 183
PCISA -9652 Half-Size CPU Card 7.6 Realtek HD Audio Driver (ALC883) Installation To install the Realtek High Definition (HD) Audio driver, please follow the steps below. NOTE: This driver only needs to be installed if an external audio kit with a RealTek ALC883 codec is installed. 7.6.1 BIOS Setup Step 1: Enter the BIOS setup. To do this, reboot the system and press DEL during POST. Step 2: Go to the Southbridge Configuration menu. Enable the High Definition Audio controller.
PAGE 184
PCISA-9652 Half-Size CPU Card Figure 7-32: Select the Audio CODEC Step 3: Double-click the ALC883 folder. Step 4: Double-click the appropriate operating system folder (Figure 7-33).
PAGE 185
PCISA -9652 Half-Size CPU Card Figure 7-33: Select the OS Step 5: Double-click the appropriate operating system version folder (Figure 7-34). Figure 7-34: Select the OS Version Step 6: Double-click the Setup.exe program icon in Figure 7-35.
PAGE 186
PCISA-9652 Half-Size CPU Card Figure 7-35: Locate the Setup Program Icon Step 7: The InstallShield Wizard starts (Figure 7-36). Figure 7-36: The InstallShield Wizard Starts Step 8: The InstallShield Wizard is prepared to guide the user through the rest of the process (Figure 7-37).
PAGE 187
PCISA -9652 Half-Size CPU Card Figure 7-37: Preparing Setup Screen Step 9: Once initialized, the InstallShield Wizard welcome screen appears (Figure 7-38). Figure 7-38: InstallShield Wizard Welcome Screen Step 10: Click NEXT to continue the installation. Step 11: InstallShield starts to install the new software as shown in Figure 7-39.
PAGE 188
PCISA-9652 Half-Size CPU Card Figure 7-39: Audio Driver Software Configuration Step 12: The Installation Wizard updates the system as shown in Figure 7-40. Figure 7-40: Installation Wizard Updates the System Step 13: After the driver installation process is complete, a confirmation screen appears (Figure 7-41).
PAGE 189
PCISA -9652 Half-Size CPU Card Figure 7-41: Restart the Computer Step 14: The confirmation screen offers the option of restarting the computer now or later. For the settings to take effect, the computer must be restarted. Click FINISH to restart the computer. Step 0: 7.7 Intel® Matrix Storage Manager Driver Installation To install the Intel® Matrix Storage Manager driver, please follow the steps below: Step 1: Select SATA from the list in Figure 7-2. Step 2: A new window opens (Figure 7-42).
PAGE 190
PCISA-9652 Half-Size CPU Card Figure 7-42: SATA RAID Driver Installation Program Step 3: Double-click the Intel Matrix Storage Manager folder. Step 4: Double-click the iata75_cd.exe program icon in Figure 7-43.
PAGE 191
PCISA -9652 Half-Size CPU Card Figure 7-43: SATA RAID Setup Program Icon Step 5: Figure 7-44 shows the InstallShield Wizard preparing to guide the user through the rest of the process.
PAGE 192
PCISA-9652 Half-Size CPU Card Step 6: Figure 7-45 shows the Matrix Storage Manager software configuring the installation process. Figure 7-45: Matrix Storage Manager Setup Screen Step 7: Figure 7-46 shows the Matrix Storage Manager welcome screen. Figure 7-46: Matrix Storage Manager Welcome Screen Step 8: Click NEXT and a warning appears (Figure 7-47).
PAGE 193
PCISA -9652 Half-Size CPU Card and decide whether or not to continue the installation process. Figure 7-47: Matrix Storage Manager Warning Screen Step 9: Click NEXT and a license agreement appears (Figure 7-48). Figure 7-48: Matrix Storage Manager License Agreement Step 10: Read the license agreement. To accept the terms and conditions stipulated in the license agreement shown, click YES and the Readme information file shown in Figure 7-49 appears.
PAGE 194
PCISA-9652 Half-Size CPU Card Figure 7-49: Matrix Storage Manager Readme File Step 11: Read the Readme file information and click NEXT. Step 12: After the driver installation process is complete, a confirmation screen appears (Figure 7-50). Figure 7-50: Matrix Storage Manager Setup Complete Step 13: The confirmation screen offers the option of restarting the computer now or later.
PAGE 195
PCISA -9652 Half-Size CPU Card For the settings to take effect, the computer must be restarted. Click FINISH to restart the computer.
PAGE 196
PCISA-9652 Half-Size CPU Card THIS PAGE IS INTENTIONALLY LEFT BLANK Page 176
PAGE 197
PCISA -9652 Half-Size CPU Card Appendix A A BIOS Configuration Options Page 177
PAGE 198
PCISA-9652 Half-Size CPU Card A.1 BIOS Configuration Options Below is a list of BIOS configuration options described in Chapter 6. System Overview ................................................................................................ 104 System Time [xx:xx:xx] ...................................................................................... 105 System Date [xx/xx/xx] .......................................................................................
PAGE 199
PCISA -9652 Half-Size CPU Card Serial Port Number [COM1] ............................................................................... 121 Base Address, IRQ [3F8h,4]............................................................................... 121 Serial Port Mode [115200 8,n,1]......................................................................... 121 Redirection After BIOS POST [Always] ............................................................ 122 Terminal Type [ANSI] .............................
PAGE 200
PCISA-9652 Half-Size CPU Card TV Standard [VBIOS-Default]............................................................................. 139 HDA Controller [Enabled] .................................................................................. 140 Save Changes and Exit ...................................................................................... 141 Discard Changes and Exit ................................................................................. 141 Discard Changes......................
PAGE 201
PCISA -9652 Half-Size CPU Card Appendix B B Terminology Page 181
PAGE 202
PCISA-9652 Half-Size CPU Card AC ’97 Audio Codec 97 (AC’97) refers to a codec standard developed by Intel® in 1997. ACPI Advanced Configuration and Power Interface (ACPI) is an OS-directed configuration, power management, and thermal management interface. AHCI Advanced Host Controller Interface (AHCI) is a SATA Host controller register-level interface. ATA The Advanced Technology Attachment (ATA) interface connects storage devices including hard disks and CD-ROM drives to a computer.
PAGE 203
PCISA -9652 Half-Size CPU Card COM COM refers to serial ports. Serial ports offer serial communication to expansion devices. The serial port on a personal computer is usually a male DB-9 connector. DAC The Digital-to-Analog Converter (DAC) converts digital signals to analog signals. DDR Double Data Rate refers to a data bus transferring data on both the rising and falling edges of the clock signal.
PAGE 204
PCISA-9652 Half-Size CPU Card protocols used to enable electronic devices to wirelessly communicate with each other. L1 Cache The Level 1 Cache (L1 Cache) is a small memory cache built into the system processor. L2 Cache The Level 2 Cache (L2 Cache) is an external processor memory cache. LCD Liquid crystal display (LCD) is a flat, low-power display device that consists of two polarizing plates with a liquid crystal panel in between.
PAGE 205
PCISA -9652 Half-Size CPU Card to automatic status checking technology implemented on hard disk drives. UART Universal Asynchronous Receiver-transmitter (UART) is responsible for asynchronous communications on the system and manages the system’s serial communication (COM) ports. UHCI The Universal Host Controller Interface (UHCI) specification is a register-level interface description for USB 1.1 Host Controllers. USB The Universal Serial Bus (USB) is an external bus standard for interfacing devices.
PAGE 206
PCISA-9652 Half-Size CPU Card THIS PAGE IS INTENTIONALLY LEFT BLANK Page 186
PAGE 207
PCISA -9652 Half-Size CPU Card Appendix C C DIO Interface Page 187
PAGE 208
PCISA-9652 Half-Size CPU Card C.1 DIO Interface Introduction The DIO connector on the PCISA-9652 is interfaced to GPIO ports on the IT8712F Super I/O chipset. The DIO has both 4-bit digital inputs and 4-bit digital outputs. The digital inputs and digital outputs are generally control signals that control the on/off circuit of external devices or TTL devices. Data can be read or written to the selected address to enable the DIO functions.
PAGE 209
PCISA -9652 Half-Size CPU Card C.3 Assembly Language Samples C.3.1 Enable the DIO Input Function The BIOS interrupt call INT 15H controls the digital I/O. An assembly program to enable digital I/O input functions is listed below. MOV AX, 6F08H Sets the digital port as input INT 15H Initiates the INT 15H BIOS call C.3.2 Enable the DIO Output Function The BIOS interrupt call INT 15H controls the digital I/O. An assembly program to enable digital I/O output functions is listed below.
PAGE 210
PCISA-9652 Half-Size CPU Card THIS PAGE IS INTENTIONALLY LEFT BLANK Page 190
PAGE 211
PCISA -9652 Half-Size CPU Card Appendix D D Watchdog Timer Page 191
PAGE 212
PCISA-9652 Half-Size CPU Card NOTE: The following discussion applies to DOS environment. IEI support is contacted or the IEI website visited for specific drivers for more sophisticated operating systems, e.g., Windows and Linux. The Watchdog Timer is provided to ensure that standalone systems can always recover from catastrophic conditions that cause the CPU to crash. This condition may have occurred by external EMI or a software bug.
PAGE 213
PCISA -9652 Half-Size CPU Card NOTE: When exiting a program it is necessary to disable the Watchdog Timer, otherwise the system resets.
PAGE 214
PCISA-9652 Half-Size CPU Card THIS PAGE IS INTENTIONALLY LEFT BLANK Page 194
PAGE 215
PCISA -9652 Half-Size CPU Card Appendix E E Address Mapping Page 195
PAGE 216
PCISA-9652 Half-Size CPU Card E.
PAGE 217
PCISA -9652 Half-Size CPU Card E.3 IRQ Mapping Table IRQ Description IRQ Description IRQ0 System Timer IRQ8 RTC clock IRQ1 Keyboard IRQ9 ACPI IRQ2 Available IRQ10 COM 4 IRQ3 COM2 IRQ11 COM 3 IRQ4 COM1 IRQ12 PS/2 mouse IRQ5 SMBus Controller IRQ13 FPU IRQ6 FDC IRQ14 Primary IDE IRQ7 Parallel port IRQ15 Secondary IDE Table E-3: IRQ Mapping Table E.
PAGE 218
PCISA-9652 Half-Size CPU Card THIS PAGE IS INTENTIONALLY LEFT BLANK Page 198
PAGE 219
PCISA -9652 Half-Size CPU Card Appendix F F Compatibility Page 199
PAGE 220
PCISA-9652 Half-Size CPU Card NOTE: The compatible items described here have been tested by the IEI R&D team and found to be compatible with the PCISA-9652. F.1 Compatible Processors The following Socket 478 processors have been successfully tested on the PCISA-9652. CPU Model Number Frequency FSB Intel® Core™2 Duo T7500 2.20 GHz 800 MHz Intel® Core™2 Duo T7300 2.00 GHz 800 MHz Intel® Core™2 Duo T7100 1.80 GHz 800 MHz Intel® Celeron® 550 2.00 GHz 533 MHz Intel® Celeron® 540 1.
PAGE 221
PCISA -9652 Half-Size CPU Card KingBOX DDR2 512MB 667MHz 512 MB 667 MHz UNIGEN UG12T6400L8DU-5AM 1 GB 533 MHz Transcend 1GB DDR2 533 1 GB 533 MHz Transcend 1GB DDR2 667 1 GB 667 MHz Transcend 2GB DDR2 800 2 GB 800 MHz Apacer 2GB UNB PC2-6400 CL5 2 GB 800 MHz Apacer 1GB UNB PC2-4300 CL4 1 GB 533 MHz UMAX RMUMX 512DDR533C 512 MB 533 MHz DSL 512MB DDR2 667MHz CL5 512 MB 667 MHz DSL 1GB DDR2 533MHz CL4 1 GB 533 MHz Page 201
PAGE 222
PCISA-9652 Half-Size CPU Card THIS PAGE IS INTENTIONALLY LEFT BLANK Page 202
PAGE 223
PCISA -9652 Half-Size CPU Card Appendix G G Hazardous Materials Disclosure Page 203
PAGE 224
PCISA-9652 Half-Size CPU Card G.1 Hazardous Material Disclosure Table for IPB Products Certified as RoHS Compliant Under 2002/95/EC Without Mercury The details provided in this appendix are to ensure that the product is compliant with the Peoples Republic of China (China) RoHS standards. The table below acknowledges the presences of small quantities of certain materials in the product, and is applicable to China RoHS only.
PAGE 225
PCISA -9652 Half-Size CPU Card Part Name Toxic or Hazardous Substances and Elements Lead Mercury Cadmium Hexavalent Polybrominated Polybrominated (Pb) (Hg) (Cd) Chromium Biphenyls Diphenyl Ethers (CR(VI)) (PBB) (PBDE) Housing X O O O O X Display X O O O O X Printed Circuit X O O O O X Metal Fasteners X O O O O O Cable Assembly X O O O O X Fan Assembly X O O O O X Power Supply X O O O O X O O O O O Board Assemblies Battery O O: This to
PAGE 226
PCISA-9652 Half-Size CPU Card 此附件旨在确保本产品符合中国 RoHS 标准。以下表格标示此产品中某有毒物质的含量符合中国 RoHS 标准规定的限量要求。本产品上会附有”环境友好使用期限”的标签，此期限是估算这些物质”不会有泄漏或突变”的年限。本产品可能包含有较短的环境友好使用期限的可替换元件，像是电池或灯管，这些元件将会单独标示出来。部件名称有毒有害物质或元素铅汞镉六价铬多溴联苯多溴二苯醚 (Pb) (Hg) (Cd) (CR(VI)) (PBB) (PBDE) 壳体 X O O O O X 显示 X O O O O X 印刷电路板 X O O O O X 金属螺帽 X O O O O O 电缆组装 X O O O O X 风扇组装 X O O O O X 电力供应组装 X O O O O X 电池 O O O O O O O: 表示该有毒有害物质在该部件所有物质材料中的含量均在 SJ/T11363-2006 标准规定的
PAGE 227
PCISA -9652 Half-Size CPU Card H Index Page 207
PAGE 228
PCISA-9652 Half-Size CPU Card socket ....................................................46 Ａ ACPI ........................................................127 airflow ........................................................90 ALC883........................................................7 AMI BIOS.....................................................7 anti-static precautions..........................34, 74 anti-static pad ..................................34, 74 anti-static wristband........................
PAGE 229
PCISA-9652 Half-Size CPU Card fan..........................................................49 panel..................................................11 floppy disk .............................................50 DIMM .........................................................81 front panel..............................................53 installation..............................................81 IDE.........................................................54 specifcations...............................
PAGE 230
PCISA -9652 Half-Size CPU Card ＨＫ HDTV .......................................................3, 6 keyboard controller ....................................28 heat sink ....................................................79 keyboard/mouse ........................................57 keyboard/mouse connector .......................57 Ｉ ICH8ME .......................................................6 location and pinouts...............................57 Ｌ IDE device ......................................
PAGE 231
PCISA-9652 Half-Size CPU Card Ｐ SDVO connector ........................................62 location and pinouts...............................62 parallel port ................................ 28, 117, 118 serial port connector ..................................64 parallel port connector ...............................60 location and pinouts...............................64 location and pinouts ..............................60 serial ports .................................................
PAGE 232
PCISA -9652 Half-Size CPU Card USB port ....................................................71 connection .............................................98 ＶＷ VGA ...........................................................98 warranty validation .....................................76 VGA monitor ..............................................