PICOe-945GSE Half-Size CPU Card PICOe-945GSE CPU Card MODEL: PICOe-945GSE Half-size PCIe CPU Card with Intel® Atom™ Processor, 512 MB On-board Memory, VGA/LVDS/HDTV-out Dual GbE, Seven USB 2.0, CF Slot and Two SATA User Manual Page 1 Rev. 1.
PICOe-945GSE Half-Size CPU Card Revision Date Version Changes 23 October, 2013 1.02 Modified Section 2.5.4.1: PCI GbE Controllers 11 March, 2009 1.01 Changed model name 28 November, 2008 1.
PICOe-945GSE Half-Size CPU Card Copyright COPYRIGHT NOTICE The information in this document is subject to change without prior notice in order to improve reliability, design and function and does not represent a commitment on the part of the manufacturer. In no event will the manufacturer be liable for direct, indirect, special, incidental, or consequential damages arising out of the use or inability to use the product or documentation, even if advised of the possibility of such damages.
PICOe-945GSE Half-Size CPU Card Manual Conventions WARNING! Warnings appear where overlooked details may cause damage to the equipment or result in personal injury. Warnings should be taken seriously. Warnings are easy to recognize. The word “warning” is written as “WARNING,” both capitalized and bold and is followed by text. The text is the warning message. A warning message is shown below: WARNING: This is an example of a warning message.
PICOe-945GSE Half-Size CPU Card NOTE: These messages inform the reader of essential but non-critical information. These messages should be read carefully as any directions or instructions contained therein can help avoid making mistakes. Notes are easy to recognize. The word “note” is written as “NOTE,” both capitalized and bold and is followed by text. The text is the cautionary message. A note message is shown below: NOTE: This is an example of a note message. Notes should always be read.
PICOe-945GSE Half-Size CPU Card Packing List NOTE: If any of the components listed in the checklist below are missing, please do not proceed with the installation. Contact the IEI reseller or vendor you purchased the PICOe-945GSE from or contact an IEI sales representative directly. To contact an IEI sales representative, please send an email to sales@iei.com.tw. 0H The items listed below should all be included in the PICOe-945GSE package.
PICOe-945GSE Half-Size CPU Card Table of Contents 1 INTRODUCTION................................................................................................... 19 1H 398H 1.1 OVERVIEW................................................................................................................ 20 1.1.1 PICOe-945GSE Introduction ........................................................................... 20 1.2 PICOE-945GSE OVERVIEW ...................................................................
PICOe-945GSE Half-Size CPU Card 2.5.2.2 Intel® ICH7-M High Definition (HD) Audio Controller .......................... 37 2.5.3 Intel® ICH7-M Low Pin Count (LPC) Interface .............................................. 37 2.5.4 Intel® ICH7-M PCI Interface........................................................................... 38 2.5.4.1 PCI GbE Controllers ................................................................................. 38 2.5.5 Intel® ICH7-M PCIe Bus ....................................
PICOe-945GSE Half-Size CPU Card 4.1.3 External Interface Panel Connectors............................................................... 54 4.2 INTERNAL PERIPHERAL CONNECTORS ...................................................................... 55 4.2.1 ATX Power Supply Enable Connector ............................................................. 55 4.2.2 Audio Connector (9-pin) .................................................................................. 56 4.2.3 Backlight Inverter Connector .......
PICOe-945GSE Half-Size CPU Card 5.5.2 CF Card Setup ................................................................................................. 86 5.5.3 Clear CMOS Jumper........................................................................................ 87 5.5.4 LVDS Panel Resolution Jumper....................................................................... 88 5.5.5 LVDS Voltage Selection.................................................................................... 90 5.5.
PICOe-945GSE Half-Size CPU Card 6.3.3 Super IO Configuration ................................................................................. 121 6.3.4 Hardware Health Configuration.................................................................... 124 6.3.5 Power Configuration...................................................................................... 128 6.3.5.1 ACPI configuration ................................................................................. 129 6.3.6 APM Configuration.....
PICOe-945GSE Half-Size CPU Card C.3.2 Enable the DIO Output Function .................................................................. 186 165H 562H D WATCHDOG TIMER .......................................................................................... 187 E ADDRESS MAPPING.......................................................................................... 190 16H 167H 563H 564H E.1 I/O ADDRESS MAP .........................................................................................
PICOe-945GSE Half-Size CPU Card List of Figures Figure 1-1: PICOe-945GSE .........................................................................................20 173H 570H Figure 1-2: PICOe-945GSE Overview [Front View] ..................................................21 174H 571H Figure 1-3: PICOe-945GSE Overview [Solder Side].................................................22 175H 572H Figure 2-1: PICOe-945GSE Dimensions (mm)..........................................................
PICOe-945GSE Half-Size CPU Card Figure 4-12: LVDS LCD Connector Pinout Location ...............................................65 201H 598H Figure 4-13: Parallel Port Connector Location.........................................................66 20H 59H Figure 4-14: SATA Drive Connector Locations........................................................67 203H 60H Figure 4-15: COM Connector Pinout Locations .......................................................
PICOe-945GSE Half-Size CPU Card Figure 7-1: Start Up Screen..................................................................................... 154 23H 630H Figure 7-2: Select Operating System ..................................................................... 154 234H 631H Figure 7-3: Drivers.................................................................................................... 155 235H 632H Figure 7-4: Chipset Driver Screen ............................................................
PICOe-945GSE Half-Size CPU Card List of Tables Table 1-1: Technical Specifications ..........................................................................25 26H 659H Table 2-1: Power Consumption .................................................................................46 263H 60H Table 4-1: Peripheral Interface Connectors..............................................................54 264H 61H Table 4-2: Rear Panel Connectors..................................................................
PICOe-945GSE Half-Size CPU Card Table 5-4: Clear CMOS Jumper Settings ..................................................................88 290H 687H Table 5-5: LVDS Panel Resolution Jumper Settings ...............................................89 291H 68H Table 5-6: LVDS Voltage Selection Jumper Settings ..............................................90 29H 689H Table 5-7: PCIe Status Select Jumper Settings .......................................................
PICOe-945GSE Half-Size CPU Card List of BIOS Menus Menu 1: Main............................................................................................................. 111 296H 693H Menu 2: Advanced.................................................................................................... 113 297H 694H Menu 3: CPU Configuration .................................................................................... 113 298H 695H Menu 4: IDE Configuration ....................................
PICOe-945GSE Half-Size CPU Card Chapter 1 1 Introduction Page 19
PICOe-945GSE Half-Size CPU Card 1.1 Overview Figure 1-1: PICOe-945GSE 1.1.1 PICOe-945GSE Introduction The PICOe-945GSE half-size PCIe CPU card is embedded 45 nm Intel® Atom™ processor platform. The Intel® Atom™ processor N270 embedded on the PICOe-945GSE has a 1.60 GHz clock speed, a 533 MHz FSB and a 512 KB L2 cache. The PICOe-945GSE has 512 MB 533 MHz DDR2 memory onboard and also supports one 200-pin 533 MHz 2.0 GB (max.) DDR2 SDRAM SO-DIMM.
PICOe-945GSE Half-Size CPU Card 1.2 PICOe-945GSE Overview 1.2.1 PICOe-945GSE Overview Photo The PICOe-945GSE has a wide variety of peripheral interface connectors. Figure 1-2 is a 746H1 labeled photo of the peripheral interface connectors on the PICOe-945GSE. Figure 1-2: PICOe-945GSE Overview [Front View] Figure 1-3 shows the rear side of the PICOe-945GSE.
PICOe-945GSE Half-Size CPU Card Figure 1-3: PICOe-945GSE Overview [Solder Side] 1.2.
PICOe-945GSE Half-Size CPU Card 1 x SDVO connector 2 x RS-232 serial port connectors 1 x TV Out connector 3 x USB 2.0 connectors (supports six USB 2.0 devices) The PICOe-945GSE has the following external peripheral interface connectors on the board rear panel. 2 x Ethernet connectors 1 x PS/2 connector 1 x USB connector 1 x VGA connector The PICOe-945GSE has the following on-board jumpers: AT power selection Clear CMOS CF card setup LVDS Voltage Selection LVDS Panel Resolution Selection J_PCIE1 1.2.
PICOe-945GSE Half-Size CPU Card One 512 MB 533 MHz DDR2 memory on-board Memory One 200-pin SO-DIMM socket supports one 533/400 MHz 2.0 GB (max.) DDR2 SDRAM SO-DIMM CompactFlash® One CompactFlash® Type I/II socket Super I/O ITE IT8718F Intel® Generation 3.5 integrated GFX core (133 MHz) Display HDTV with 1080i maximum resolution supported 18-bit dual-channel LVDS integrated in Intel® 945GSE BIOS AMI BIOS label 5.1 channel audio kit with Realtek ALC655 AC'97 codec Audio 7.
PICOe-945GSE Half-Size CPU Card One infrared connector through the ITE super I/O. Supports: Infrared Serial Infrared (SIR) Amplitude Shift Keyed IR (ASKIR) Power Supply ATX and AT power supported 5V @ 2.89A, 12V@0.22A, 5VSB@0.03A Power Consumption (1.
PICOe-945GSE Half-Size CPU Card Chapter 2 2 Detailed Specifications Page 26
PICOe-945GSE Half-Size CPU Card 2.1 Dimensions 2.1.
PICOe-945GSE Half-Size CPU Card 2.1.2 External Interface Panel Dimensions External peripheral interface connector panel dimensions are shown in Figure 2-2. 748H1 Figure 2-2: External Interface Panel Dimensions (mm) 2.2 Data Flow Figure 2-3 shows the data flow between the two on-board chipsets and other components 749H18 installed on the CPU card and described in the following sections of this chapter.
PICOe-945GSE Half-Size CPU Card Figure 2-3: Data Flow Block Diagram 2.3 Embedded PICOe-945GSE Processor 2.3.1 Overview The PICOe-945GSE comes with an embedded 45 nm 1.60 GHz Intel® Atom™ processor N270. The processor supports a 533 MHz FSB and has a 1.6 GHz 512 KB L2 cache.
PICOe-945GSE Half-Size CPU Card low power processor has a maximum power of 2.5 W. The processor is shown in Figure 719H 2-4 below. Figure 2-4: Embedded Processor 2.3.
PICOe-945GSE Half-Size CPU Card Advanced power management features including Enhanced Intel SpeedStep® Technology Execute Disable Bit support for enhanced security 2.3.3 Front Side Bus (FSB) The Intel® Atom™ processor on the PICOe-945GSE is interfaced to the Intel® 945GSE through a 533 MHz front side bus (FSB). The FSB is shown in Figure 2-5 below.
PICOe-945GSE Half-Size CPU Card 2.4 Intel 945GSE Northbridge Chipset 2.4.1 Intel® 945GSE Overview The Intel® 945GSE Graphics and Memory Controller Hub (GMCH) supports the embedded Intel® Atom™ N270 processor. The Intel® 945GSE is interfaced to the processor through a 533 MHz FSB. 2.4.2 Intel® 945GSE DDR2 Controller 2.4.2.1 On-board DDR2 SDRAM 512 MB 533 MHz DDR2 SDRAM is embedded on the PICOe-945GSE. The on-board SDRAM chips are shown in Figure 2-6. 721H Figure 2-6: On-board DDR2 SDRAM Chips 2.4.2.
PICOe-945GSE Half-Size CPU Card Support for DDR2 at 400 MHz and 533 MHz No support for Dual-Channel Interleaved mode of operation Enhanced Addressing support (Swap only) The SO-DIMM socket is shown in Figure 2-7 below. 72H Figure 2-7: DDR2 SO-DIMM Socket 2.4.3 Intel® 945GSE Graphics The Intel® 945GSE supports CRT, LVDS, TV-Out and SDVO. The internal graphics engine has the following features: Intel® Gen 3.5 Integrated Graphics Engine 250-MHz core render clock and 200 MHz core display clock at 1.
PICOe-945GSE Half-Size CPU Card Microsoft DirectX* 9.1 operating system Intermediate Z in Classic Rendering Internal Graphics Display Device States: D0, D1, D3 Graphics Display Adapter States: D0, D3. 2.4.3.1 Analog CRT Graphics Mode The analog CRT bus is interfaced to an external DB-15 interface connector. The connector is shown below. Figure 2-8: VGA Connector Some of the features of the CRT include: Integrated 400-MHz RAMDAC Analog Monitor Support up to QXGA Support for CRT Hot Plug 2.4.3.
PICOe-945GSE Half-Size CPU Card Panel support up to UXGA (1600 x 1200) 25-MHz to 112-MHz single-/dual-channel; @18 bpp o TFT panel type supported Pixel Dithering for 18-bit TFT panel to emulate 24-bpp true color displays Panel Fitting. Panning, and Center Mode Supported CPIS 1.5 compliant Spread spectrum clocking supported Panel Power Sequencing support Integrated PWM interface for LCD backlight inverter control 2.4.3.3 TV Out Interface The TV Out interface has the following features.
PICOe-945GSE Half-Size CPU Card 2.5 Intel® ICH7-M Southbridge Chipset 2.5.1 Intel® ICH7-M Overview The Intel® ICH7-M chipset is connected to the Intel® 945GSE GMCH through the chip-to-chip Direct Media Interface (DMI). Some of the features of the Intel® ICH7-M are listed below. Complies with PCI Express Base Specification, Revision 1.0a Complies with PCI Local Bus Specification, Revision 2.
PICOe-945GSE Half-Size CPU Card The controllers share the same pins and only one can be activated at a time. The controllers are interfaced to the PICOe-945GSE audio connector which is in turn connected to an option audio kit with either an AC’97 codec or an HD Audio codec. 2.5.2.1 Intel® ICH7-M Audio Codec ’97 Controller The Audio Codec ’97 (AC’97) controller integrated into the ICH7-M complies with AC’97 Component Specification, Version 2.3.
PICOe-945GSE Half-Size CPU Card 2.5.4 Intel® ICH7-M PCI Interface The PCI interface on the ICH7-M is compliant with the PCI Revision 2.3 implementation. Some of the features of the PCI interface are listed below. PCI Revision 2.3 compliant 33 MHz 5V tolerant PCI signals (except PME#) Integrated PCI arbiter supports up to seven PCI bus masters The PCI bus is connected to an interface gold finger on the bottom of the CPU cards and supports four expansion PCI cards on the backplane.
PICOe-945GSE Half-Size CPU Card Figure 2-10: RJ-45 Connectors and GbE Controllers The Realtek RTL8110SC PCI GbE controllers combine a triple-speed IEEE 802.3 compliant Media Access Controller (MAC) with a triple-speed Ethernet transceiver, 32-bit PCI bus controller, and embedded memory. With state-of-the-art DSP technology and mixed-mode signal technology, they offer high-speed transmission over CAT 5 UTP cable or CAT 3 UTP (10Mbps only) cable.
PICOe-945GSE Half-Size CPU Card Supports IEEE 802.1P Layer 2 Priority Encoding Supports IEEE 802.1Q VLAN tagging Serial EEPROM Transmit/Receive on-chip buffer support Supports power down/link down power saving Supports PCI MSI (Message Signaled Interrupt) and MSI-X Supports Receive-Side Scaling (RSS) 2.5.5 Intel® ICH7-M PCIe Bus The Intel® ICH7-M chipset has four PCIe lanes.
PICOe-945GSE Half-Size CPU Card 2.5.6 Intel® ICH7-M Real Time Clock 256 bytes of battery backed RAM is provided by the Motorola MC146818A real time clock (RTC) integrated into the ICH7-M. The RTC operates on a 3V battery and 32.768KHz crystal. The RTC keeps track of the time and stores system data even when the system is turned off. 2.5.7 Intel® ICH7-M SATA Controller The integrated SATA controller on the ICH7-M supports up to two SATA drives with independent DMA operations.
PICOe-945GSE Half-Size CPU Card 2.5.8 Intel® ICH7-M USB Controller Up to seven high-speed, full-speed or low-speed USB devices are supported by the ICH7-M on the PICOe-945GSE. High-speed USB 2.0, with data transfers of up to 480MB/s, is enabled with the ICH7-M integrated Enhanced Host Controller Interface (EHCI) compliant host controller. USB full-speed and low-speed signaling is supported by the ICH7-M integrated Universal Host Controller Interface (UHCI) controllers.
PICOe-945GSE Half-Size CPU Card 2.6.2 iTE IT8718F Super I/O Chipset The iTE IT8718F Super I/O chipset is connected to the ICH7-M through the LPC bus. Figure 2-14: Super I/O The iTE IT8718F is an LPC interface-based Super I/O device that comes with Environment Controller integration.
PICOe-945GSE Half-Size CPU Card 2.6.2.1 Super I/O LPC Interface The LPC interface on the Super I/O complies with the Intel® Low Pin Count Specification Rev. 1.0. The LPC interface supports both LDRQ# and SERIRQ protocols as well as PCI PME# interfaces. 2.6.2.2 Super I/O 16C550 UARTs The onboard Super I/O has two integrated 16C550 UARTs that can support the following: Two standard serial ports (COM1 and COM2) IrDa 1.0 and ASKIR protocols 2.6.2.
PICOe-945GSE Half-Size CPU Card Supports mouse double-click and/or mouse move power on events 2.6.2.7 Super I/O Parallel Port The multi-mode high-performance parallel port supports the bi-directional Standard Parallel Port (SPP), the Enhanced Parallel Port (EPP) and the Extended Capabilities Port (ECP) modes. 2.7 Environmental and Power Specifications 2.7.
PICOe-945GSE Half-Size CPU Card The values for the above environmental parameters are all recorded in the BIOS Hardware Health Configuration menu. 2.7.2 Operating Temperature and Temperature Control The maximum and minimum operating temperatures for the PICOe-945GSE are listed below. Minimum Operating Temperature: 0ºC (32°F) Maximum Operating Temperature: 60°C (140°F) A heat sink must be installed on the CPU. Thermal paste must be smeared on the lower side of the heat sink before it is mounted on the CPU.
PICOe-945GSE Half-Size CPU Card Chapter 3 3 Unpacking Page 47
PICOe-945GSE Half-Size CPU Card 3.1 Anti-static Precautions WARNING! Failure to take ESD precautions during the installation of the PICOe-945GSE may result in permanent damage to the PICOe-945GSE and severe injury to the user. Electrostatic discharge (ESD) can cause serious damage to electronic components, including the PICOe-945GSE. Dry climates are especially susceptible to ESD.
PICOe-945GSE Half-Size CPU Card 3.3 Unpacking Checklist NOTE: If any of the components listed in the checklist below are missing, do not proceed with the installation. Contact the IEI reseller or vendor the PICOe-945GSE was purchased from or contact an IEI sales representative directly by sending an email to sales@iei.com.tw. 326H17 3.3.
PICOe-945GSE Half-Size CPU Card 1 Mini jumper pack (2.0mm) (P/N: 33100-000033-RS) 1 Utility CD 1 Quick Installation Guide 3.3.2 Optional Items The PICOe-945GSE is shipped with the following components: Item and Part Number SATA power cable (P/N: 32100-088600-RS) LPT cable (w/o bracket) (P/N: 32200-015100-RS) HDTV output cable (P/N: HDTVCABLESET-01) Audio kit_ 5.1 Channel (P/N: AC-KIT08R-R10) Audio kit_ 7.
PICOe-945GSE Half-Size CPU Card Chapter 4 4 Connectors Page 51
PICOe-945GSE Half-Size CPU Card 4.1 Peripheral Interface Connectors Section 4.1.1 shows peripheral interface connector locations. Section 4.2 lists all the 730H 731H 76H peripheral interface connectors seen in Section 4.1.1. 732H 4.1.1 PICOe-945GSE Layout Figure 4-1 shows the on-board peripheral connectors, rear panel peripheral connectors 768H3 and on-board jumpers. Figure 4-1: Connector and Jumper Locations [Front Side] Figure 4-2 shows the solder side of the PICOe-945GSE.
PICOe-945GSE Half-Size CPU Card Figure 4-2: Connector and Jumper Locations [Solder Side] 4.1.2 Peripheral Interface Connectors Table 4-1 shows a list of the peripheral interface connectors on the PICOe-945GSE. 769H35 Detailed descriptions of these connectors can be found below.
PICOe-945GSE Half-Size CPU Card Keyboard connector 6-pin wafer KB_MS1 LVDS connector 30-pin crimp LVDS1 Parallel port connector 26-pin header LPT1 Serial ATA (SATA) drive connectors 7-pin SATA S_ATA1 Serial ATA (SATA) drive connectors 7-pin SATA S_ATA2 SDVO connector 48-pin crimp SDVO1 RS-232 serial port connector 10-pin header COM1 RS-232 serial port connector 10-pin header COM2 TV Out connector 6-pin header TV1 USB 2.0 connector 8-pin header USB1 USB 2.
PICOe-945GSE Half-Size CPU Card 4.2 Internal Peripheral Connectors Internal peripheral connectors are found on the CPU card and are only accessible when the CPU card is outside of the chassis. This section has complete descriptions of all the internal, peripheral connectors on the PICOe-945GSE. 4.2.
PICOe-945GSE Half-Size CPU Card 4.2.2 Audio Connector (9-pin) CN Label: J_AUDIO1 CN Type: 9-pin header (2x5) CN Location: See Figure 4-4 CN Pinouts: See Table 4-4 741H 742H The 9-pin audio connector is connected to external audio devices including speakers and microphones for the input and output of audio signals to and from the system. Figure 4-4: Audio Connector Location (9-pin) PIN NO. DESCRIPTION PIN NO.
PICOe-945GSE Half-Size CPU Card 4.2.3 Backlight Inverter Connector CN Label: INVERTER1 CN Type: 5-pin wafer (1x5) CN Location: See Figure 4-5 CN Pinouts: See Table 4-5 743H 74H The backlight inverter connector provides the backlight on the LCD display connected to the PICOe-945GSE with +12V of power. Figure 4-5: Panel Backlight Connector Pinout Locations PIN NO.
PICOe-945GSE Half-Size CPU Card 4.2.4 CompactFlash® Socket CN Label: CF1 (solder side) CN Type: 50-pin header (2x25) CN Location: See Figure 4-6 CN Pinouts: See Table 4-6 745H 746H A CF Type I or Type II memory card is inserted to the CF socket on the solder side of the PICOe-945GSE. Figure 4-6: CF Card Socket Location PIN NO. DESCRIPTION PIN NO.
PICOe-945GSE Half-Size CPU Card PIN NO. DESCRIPTION PIN NO.
PICOe-945GSE Half-Size CPU Card The digital input/output connector is managed through a Super I/O chip. The DIO connector pins are user programmable. Figure 4-7: DIO Connector Connector Locations PIN NO. DESCRIPTION PIN NO. DESCRIPTION 1 GND 2 VCC 3 Output 3 4 Output 2 5 Output 1 6 Output 0 7 Input 3 8 Input 2 9 Input 1 10 Input 0 Table 4-7: DIO Connector Connector Pinouts 4.2.
PICOe-945GSE Half-Size CPU Card system BIOS can recognize the fan speed. Please note that only specified fans can issue the rotation signals. Figure 4-8: +12V Fan Connector Location PIN NO. DESCRIPTION 1 GND 2 +12V 3 Fan Speed Detect Table 4-8: +12V Fan Connector Pinouts 4.2.
PICOe-945GSE Half-Size CPU Card Figure 4-9: Front Panel Connector Pinout Locations (8-pin) FUNCTION PIN DESCRIPTION FUNCTION PIN DESCRIPTION Power 1 PWR_BTN+ Power LED 2 PWR_LED+ Button 3 PWR_BTN- 4 PWR_LED- HDD LED 5 HDD_LED+ 6 RESET+ 7 HDD_LED- 8 RESET- Reset Table 4-9: Front Panel Connector Pinouts (8-pin) 4.2.
PICOe-945GSE Half-Size CPU Card Figure 4-10: Infrared Connector Pinout Locations PIN NO. DESCRIPTION 1 VCC 2 NC 3 IR-RX 4 GND 5 IR-TX Table 4-10: Infrared Connector Pinouts 4.2.9 Keyboard/Mouse Connector CN Label: KB_MS1 CN Type: 6-pin header (1x6) CN Location: See Figure 4-11 CN Pinouts: See Table 4-11 75H 756H The keyboard and mouse connector can be connected to a standard PS/2 cable or PS/2 Y-cable to add keyboard and mouse functionality to the system.
PICOe-945GSE Half-Size CPU Card Figure 4-11: Keyboard/Mouse Connector Location PIN NO. DESCRIPTION 1 VCC5_KBMS 2 MS DATA 3 MS CLK 4 KB DATA 5 KB CLK 6 GROUND Table 4-11: Keyboard/Mouse Connector Pinouts 4.2.10 LVDS LCD Connector CN Label: LVDS1 CN Type: 30-pin crimp (3x10) CN Location: See Figure 4-12 CN Pinouts: See Table 4-12 789H5 790H58 The 30-pin LVDS LCD connectors can be connected to single channel or dual channel, 24-bit or 36-bit LVDS panel.
PICOe-945GSE Half-Size CPU Card Figure 4-12: LVDS LCD Connector Pinout Location PIN NO. DESCRIPTION PIN NO.
PICOe-945GSE Half-Size CPU Card 4.2.11 Parallel Port Connector CN Label: LPT1 CN Type: 26-pin header CN Location: See Figure 4-13 CN Pinouts: See Table 4-13 759H 760H The 26-pin parallel port connector connects to a parallel port connector interface or some other parallel port device such as a printer. Figure 4-13: Parallel Port Connector Location PIN NO. DESCRIPTION PIN NO.
PICOe-945GSE Half-Size CPU Card PIN NO. DESCRIPTION PIN NO. DESCRIPTION 17 PRINTER SELECT LN# 18 GROUND 19 GROUND 20 GROUND 21 GROUND 22 GROUND 23 GROUND 24 GROUND 25 GROUND 26 NC Table 4-13: Parallel Port Connector Pinouts 4.2.12 SATA Drive Connectors CN Label: S_ATA1 and S_ATA2 CN Type: 7-pin SATA drive connectors CN Location: See Figure 4-14 CN Pinouts: See Table 4-14 793H61 794H62 The two SATA drive connectors are each connected to a first generation SATA drive.
PICOe-945GSE Half-Size CPU Card 3 TX- 4 GND 5 RX- 6 RX+ 7 GND Table 4-14: SATA Drive Connector Pinouts 4.2.13 Serial Port Connectors (COM 1 and COM 2) CN Label: COM1 and COM2 CN Type: 10-pin header (2x5) CN Location: See Figure 4-15 CN Pinouts: See Table 4-15 795H63 796H4 The 10-pin serial port connector provides a second RS-232 serial communications channel. The COM serial port connectors can be connected to external RS-232 serial port devices.
PICOe-945GSE Half-Size CPU Card PIN NO. DESCRIPTION PIN NO. DESCRIPTION 1 Data Carrier Direct (DCD) 2 Receive Data (SIN) 3 Transmit Data (SOUT) 4 Data Terminal Ready (DTR) 5 Ground (GND) 6 DATA Set Ready (DSR) 7 Request To Send (RTS) 8 Clear To Send (CTS) 9 Ring Indicator (XRI) 10 N/C Table 4-15: COM Connector Pinouts 4.2.
PICOe-945GSE Half-Size CPU Card Figure 4-16: SDVO Connector Pinout Locations PIN NO. DESCRIPTION PIN NO.
PICOe-945GSE Half-Size CPU Card 12 SDVOB_GREEN+ 36 SDVO_TVCLKIN+ 13 GROUND 37 GROUND 14 NC 38 SDVO_CLK 15 NC 39 SDVO_DATA 16 GROUND 40 PCIRST 17 SDVOB_INT+ 41 +5VS 18 SDVOB_INT+ 42 +5VS 19 GROUND 43 +5VS 20 NC 44 NC 21 NC 45 NC 22 GROUND 46 GROUND 23 NC 47 GROUND 24 NC Table 4-16: SDVO Connector Pinouts 4.2.
PICOe-945GSE Half-Size CPU Card Figure 4-17: TV Connector Pinout Locations S-Video Connector PIN NO. DESCRIPTION PIN NO. DESCRIPTION 1 GND 2 AGREEN_Y 3 GND 4 ARED_C RCA Connector (only video signal) 5 GND 6 ABLUE_CVBS Table 4-17: TV Port Connector Pinouts 4.2.16 USB Connectors (Internal) CN Label: USB1, USB2 and USB3 CN Type: 8-pin header (2x4) CN Location: See Figure 4-18 CN Pinouts: See Table 4-18 801H769 802H7 The 2x4 USB pin connectors each provide connectivity to two USB 1.
PICOe-945GSE Half-Size CPU Card Figure 4-18: USB Connector Pinout Locations PIN NO. DESCRIPTION PIN NO. DESCRIPTION 1 VCC 2 GND 3 DATA- 4 DATA- 5 DATA+ 6 DATA+ 7 GND 8 VCC Table 4-18: USB Port Connector Pinouts 4.3 External Peripheral Interface Connector Panel Figure 4-19 shows the PICOe-945GSE external peripheral interface connector (EPIC) 803H71 panel.
PICOe-945GSE Half-Size CPU Card Figure 4-19: PICOe-945GSE External Peripheral Interface Connector 4.3.1 Keyboard/Mouse Connector CN Label: KB_MS2 CN Type: PS/2 CN Location: See Figure 4-19 CN Pinouts: See Figure 4-20, Table 4-19 72H 73H 74H The PICOe-945GSE keyboard and mouse connector is a standard PS/2 connector.
PICOe-945GSE Half-Size CPU Card 4.3.2 LAN Connectors CN Label: LAN1 and LAN2 CN Type: RJ-45 CN Location: See Figure 4-19 CN Pinouts: See Table 4-20 80H75 809H76 The PICOe-945GSE is equipped with two built-in RJ-45 Ethernet controllers. The controllers can connect to the LAN through two RJ-45 LAN connectors. There are two LEDs on the connector indicating the status of LAN.
PICOe-945GSE Half-Size CPU Card STATUS DESCRIPTION GREEN Activity STATUS DESCRIPTION YELLOW Linked Table 4-21: RJ-45 Ethernet Connector LEDs 4.3.3 USB Connectors CN Label: USB_C1 CN Type: USB port CN Location: See Figure 4-19 CN Pinouts: See Table 4-22 814H7 815H79 The PICOe-945GSE has two external USB 2.0 ports. The ports connect to both USB 2.0 and USB 1.1 devices. PIN NO. DESCRIPTION 1 VCC 2 DATA- 3 DATA+ 4 GND Table 4-22: USB Port Pinouts 4.3.
PICOe-945GSE Half-Size CPU Card Figure 4-22: VGA Connector PIN DESCRIPTION PIN DESCRIPTION 1 RED 2 GREEN 3 BLUE 4 NC 5 GND 6 CRT_PLUG- 7 GND 8 GND 9 VCC 10 GND 11 NC 12 DDC DAT 13 HSYNC 14 VSYNC 15 DDCCLK Table 4-23: VGA Connector Pinouts Page 77
PICOe-945GSE Half-Size CPU Card Chapter 5 5 Installation Page 78
PICOe-945GSE Half-Size CPU Card 5.1 Anti-static Precautions WARNING: Failure to take ESD precautions during the installation of the PICOe-945GSE may result in permanent damage to the PICOe-945GSE and severe injury to the user. Electrostatic discharge (ESD) can cause serious damage to electronic components, including the PICOe-945GSE. Dry climates are especially susceptible to ESD.
PICOe-945GSE Half-Size CPU Card 5.2 Installation Considerations NOTE: The following installation notices and installation considerations should be read and understood before the PICOe-945GSE is installed. All installation notices pertaining to the installation of the PICOe-945GSE should be strictly adhered to. Failing to adhere to these precautions may lead to severe damage of the PICOe-945GSE and injury to the person installing the CPU card. 5.2.
PICOe-945GSE Half-Size CPU Card o When working with the PICOe-945GSE, make sure that it is disconnected from all power supplies and that no electricity is being fed into the system. Before and during the installation of the PICOe-945GSE DO NOT: Remove any of the stickers on the PCB board. These stickers are required for warranty validation. Use the product before verifying all the cables and power connectors are properly connected.
PICOe-945GSE Half-Size CPU Card 5.3 Unpacking When the PICOe-945GSE is unpacked, please check all the unpacking list items listed in Chapter 3 are indeed present. If any of the unpacking list items are not available please contact the PICOe-945GSE vendor reseller/vendor where the PICOe-945GSE was purchased or contact an IEI sales representative. 5.4 SO-DIMM and CF Card Installation 5.4.1 SO-DIMM Installation WARNING: Using incorrectly specified SO-DIMM may cause permanently damage the PICOe-945GSE.
PICOe-945GSE Half-Size CPU Card Step 2: Align the SO-DIMM with the socket. The SO-DIMM must be oriented in such a way that the notch in the middle of the SO-DIMM must be aligned with the plastic bridge in the socket. Step 3: Insert the SO-DIMM. Push the SO-DIMM chip into the socket at an angle. (See Figure 5-1) 784H Step 4: Open the SO-DIMM socket arms. Gently pull the arms of the SO-DIMM socket out and push the rear of the SO-DIMM down. (See Figure 5-1) 785H Step 5: Secure the SO-DIMM.
PICOe-945GSE Half-Size CPU Card Figure 5-2: CF Card Installation 5.5 Jumper Settings NOTE: A jumper is a metal bridge used to close an electrical circuit. It consists of two or three metal pins and a small metal clip (often protected by a plastic cover) that slides over the pins to connect them. To CLOSE/SHORT a jumper means connecting the pins of the jumper with the plastic clip and to OPEN a jumper means removing the plastic clip from a jumper.
PICOe-945GSE Half-Size CPU Card Description Label Type AT Power Mode Setting ATXCTL1 2-pin header CF Card Setting JCF1 2-pin header Clear CMOS J_CMOS1 3-pin header LVDS Panel Resolution J_LCD_TYPE1 8-pin header LVDS Voltage Select J_VLVDS1 3-pin header PCIe Status Select J_PCIE1 2-pin header Table 5-1: Jumpers 5.5.1 AT Power Select Jumper Settings NOTE: The AT Power Select Jumper is the same as the ATX Enable connector.
PICOe-945GSE Half-Size CPU Card AT Power Select Description Short 1 – 2 Use AT power Open Use ATX power Default Table 5-2: AT Power Select Jumper Settings The location of the AT Power Select jumper is shown in Figure 5-4 below. 791H Figure 5-4: AT Power Select Jumper Location 5.5.
PICOe-945GSE Half-Size CPU Card Figure 5-5: CF Card Setup Jumper Location 5.5.3 Clear CMOS Jumper Jumper Label: J_CMOS1 Jumper Type: 3-pin header Jumper Settings: See Table 5-4 Jumper Location: See Figure 5-6 830H796 831H79 If the PICOe-945GSE fails to boot due to improper BIOS settings, the clear CMOS jumper clears the CMOS data and resets the system BIOS information. To do this, use the jumper cap to close pins 2 and 3 for a few seconds then reinstall the jumper clip back to pins 1 and 2.
PICOe-945GSE Half-Size CPU Card The clear CMOS jumper settings are shown in Table 5-4. 832H79 Clear CMOS Description Short 1 - 2 Keep CMOS Setup Short 2 - 3 Clear CMOS Setup Default Table 5-4: Clear CMOS Jumper Settings The location of the clear CMOS jumper is shown in Figure 5-6 below. 83H79 Figure 5-6: Clear CMOS Jumper 5.5.
PICOe-945GSE Half-Size CPU Card J_LCD_TYPE1 Description Open 640 x 480 (18-bit) Short 1-2 800 x 480 (18-bit) Short 3-4 800 x 600 (18-bit) Short 1-2, 3-4 1024 X 768 (18-bit) Short 5-6 1280X1024 (36-bit) Short 1-2, 5-6 1400 X 1050 (36-bit) Short 3-4, 5-6 1400 x 900 (36-bit) Short 1-2, 3-4, 5-6 1600 x 1200 (36-bit) Default Table 5-5: LVDS Panel Resolution Jumper Settings The LVDS Panel Resolution jumper location is shown in Figure 5-7.
PICOe-945GSE Half-Size CPU Card 5.5.5 LVDS Voltage Selection WARNING: Permanent damage to the screen and PICOe-945GSE may occur if the wrong voltage is selected with this jumper. Please refer to the user guide that cam with the monitor to select the correct voltage. Jumper Label: J_VLVDS1 Jumper Type: 3-pin header Jumper Settings: See Table 5-6 Jumper Location: See Figure 5-8 804H 805H The LVDS Voltage Selection jumpers allow the LVDS screen voltages to be set.
PICOe-945GSE Half-Size CPU Card Figure 5-8: LVDS Voltage Selection Jumper Pinout Locations 5.5.6 PCIe Status Select Jumper Label: J_PCIE1 Jumper Type: 2-pin header Jumper Settings: See Table 5-7 Jumper Location: See Figure 5-9 80H 809H The PCIe Status Select jumper allows the PCIe status to be configured. The PCIe Status Select jumper settings are shown in Table 5-6.
PICOe-945GSE Half-Size CPU Card Figure 5-9: PCIe Status Select Jumper Pinout Locations 5.6 Chassis Installation 5.6.1 Airflow WARNING: Airflow is critical to the cooling of the CPU and other onboard components. The chassis in which the PICOe-945GSE must have air vents to allow cool air to move into the system and hot air to move out. The PICOe-945GSE must be installed in a chassis with ventilation holes on the sides allowing airflow to travel through the heat sink surface.
PICOe-945GSE Half-Size CPU Card NOTE: IEI has a wide range of backplanes available. Please contact your PICOe-945GSE vendor, reseller or an IEI sales representative at sales@iei.com.tw or visit the IEI website (http://www.ieiworld.com.tw) 318H 319H to find out more about the available chassis. 5.6.3 CPU Card Installation To install the PICOe-945GSE CPU card onto the backplane, carefully align the CPU card interface connectors with the corresponding socket on the backplane.
PICOe-945GSE Half-Size CPU Card HDTV out cable 5.1 channel audio kit 7.1 channel audio kit 5.7.2 5.1 Channel Audio Kit Installation NOTE: This is an optional item that must be ordered separately. For further information please contact the nearest PICOe-945GSE distributor, reseller or vendor or contact an iEi sales representative directly. Send any queries to sales@iei.com.tw. 320H The optional 5.1 channel audio kit connects to the 10-pin audio connector on the PICOe-945GSE.
PICOe-945GSE Half-Size CPU Card Figure 5-10: 5.1 Channel Audio Kit Step 4: Mount the audio kit onto the chassis. Once the audio kit is connected to the PICOe-945GSE, secure the audio kit bracket to the system chassis. Step 5: Connect the audio devices. Connect one speaker to the line-in audio jack, one speaker to the line-out audio jack and a microphone to the mic-in audio jack. Step 6: Install the driver. If the 5.1 channel audio kit is used, the ALC655 Realtek codec driver must be installed.
PICOe-945GSE Half-Size CPU Card The optional 7.1 channel audio kit connects to the 10-pin audio connector on the PICOe-945GSE. The audio kit consists of five audio jacks. One audio jack, Mic In, connects to a microphone. The remaining four audio jacks, Line-In, Front-Out, Rear-Out, and Center Subwoofer, connect to speakers. To install the audio kit, please refer to the steps below: Step 1: Connect the audio kit cable. The audio kit is shipped with a cable that connects the audio kit to the PICOe-945GSE.
PICOe-945GSE Half-Size CPU Card PICOe-945GSE, secure the audio kit bracket to the system chassis. Step 5: Connect the audio devices. Connect one speaker to the line-in audio jack, one speaker to the line-out audio jack and a microphone to the mic-in audio jack. Step 6: Install the driver. If the 7.1 channel audio kit is used, the ALC883 Realtek codec driver must be installed. Refer to Chapter 7 for driver installation instructions.Step 0: 5.7.
PICOe-945GSE Half-Size CPU Card Figure 5-12: SATA Drive Cable Connection Step 3: Connect the cable to the SATA disk. Connect the connector on the other end of the cable to the connector at the back of the SATA drive. See Figure 5-13. 853H16 Step 4: Connect the SATA power cable. Connect the SATA power connector to the back of the SATA drive. See Figure 5-13.
PICOe-945GSE Half-Size CPU Card Figure 5-13: SATA Power Drive Connection 5.7.5 USB Cable (Dual Port) with Slot Bracket The PICOe-945GSE is shipped with a dual port USB 2.0 cable. To connect the USB cable connector, please follow the steps below. Step 1: Locate the connectors. The locations of the USB connectors are shown in Chapter 3. WARNING: If the USB pins are not properly aligned, the USB device can burn out. Step 2: Align the connectors. The cable has two connectors.
PICOe-945GSE Half-Size CPU Card Figure 5-14: Dual USB Cable Connection Step 4: Attach the bracket to the chassis. The USB 2.0 connectors are attached to a bracket. To secure the bracket to the chassis please refer to the installation instructions that came with the chassis.Step 0: 5.7.6 Parallel Port Cable without Bracket The optional parallel port (LPT) cable respectively connects the on-board LPT 26-pin box header to an external LPT device (like a printer).
PICOe-945GSE Half-Size CPU Card Step 2: Align the connectors. Correctly align pin 1 on the cable connector with pin 1 on the PICOe-945GSE LPT box-header connector. See Figure 5-15. 819H Step 3: Insert the cable connectors. Once the cable connector is properly aligned with the 26-pin box-header connector on the PICOe-945GSE, connect the cable connector to the on-board connector. See Figure 5-15. 820H Figure 5-15: LPT Cable Connection Step 4: Attach the LPT connector to the chassis.
PICOe-945GSE Half-Size CPU Card Figure 5-16: Connect the LPT Device 5.7.7 Dual RS-232 Cable with Slot Bracket The dual RS-232 cable slot connector consists of two connectors attached to two independent cables. Each cable is then attached to a D-sub 9 male connector that is mounted onto a slot. To install the dual RS-232 cable, please follow the steps below. Step 1: Locate the connectors. The locations of the RS-232 connectors are shown in Chapter 3. Step 2: Insert the cable connectors.
PICOe-945GSE Half-Size CPU Card Figure 5-17: Dual RS-232 Cable Installation Step 3: Secure the bracket. The dual RS-232 connector has two D-sub 9 male connectors secured on a bracket. To secure the bracket to the chassis please refer to the reference material that came with the chassisStep 0: 5.8 External Peripheral Interface Connection The following external peripheral devices can be connected to the external peripheral interface connectors.
PICOe-945GSE Half-Size CPU Card 5.8.1 LAN Connection (Single Connector) There are two external RJ-45 LAN connectors. The RJ-45 connectors enable connection to an external network. To connect a LAN cable with an RJ-45 connector, please follow the instructions below. Step 1: Locate the RJ-45 connectors. The locations of the USB connectors are shown in Chapter 4. Step 2: Align the connectors. Align the RJ-45 connector on the LAN cable with one of the RJ-45 connectors on the PICOe-945GSE. See Figure 5-18.
PICOe-945GSE Half-Size CPU Card Step 1: Locate the dual PS/2 connector. The location of the PS/2 connector is shown in Chapter 3. Step 2: Insert the keyboard/mouse connector. Insert the PS/2 connector on the end of the PS/2 y-cable into the external PS/2 connector. See Figure 5-19. 824H Figure 5-19: PS/2 Keyboard/Mouse Connector Step 3: Connect the keyboard and mouse. Connect the keyboard and mouse to the appropriate connector.
PICOe-945GSE Half-Size CPU Card Series "A" receptacle connectors are shown in Chapter 3. Step 2: Insert a USB Series "A" plug. Insert the USB Series "A" plug of a device into the USB Series "A" receptacle on the external peripheral interface. See Figure 862H5 5-20. Figure 5-20: USB Connector 5.8.4 VGA Monitor Connection The PICOe-945GSE has a single female DB-15 connector on the external peripheral interface panel. The DB-15 connector is connected to a CRT or VGA monitor.
PICOe-945GSE Half-Size CPU Card insert the male connector from the VGA screen into the female connector on the PICOe-945GSE. See Figure 5-21. 863H2 Figure 5-21: VGA Connector Step 4: Secure the connector. Secure the DB-15 VGA connector from the VGA monitor to the external interface by tightening the two retention screws on either side of the connector.
PICOe-945GSE Half-Size CPU Card Chapter 6 6 BIOS Screens Page 108
PICOe-945GSE Half-Size CPU Card 6.1 Introduction A licensed copy of AMI BIOS is preprogrammed into the ROM BIOS. The BIOS setup program allows users to modify the basic system configuration. This chapter describes how to access the BIOS setup program and the configuration options that may be changed. 6.1.1 Starting Setup The AMI BIOS is activated when the computer is turned on. The setup program can be activated in one of two ways. 1. Press the DELETE key as soon as the system is turned on or 2.
PICOe-945GSE Half-Size CPU Card F1 key General help, only for Status Page Setup Menu and Option Page Setup Menu F2 /F3 key Change color from total 16 colors. F2 to select color forward. F10 key Save all the CMOS changes, only for Main Menu Table 6-1: BIOS Navigation Keys 6.1.3 Getting Help When F1 is pressed a small help window describing the appropriate keys to use and the possible selections for the highlighted item appears. To exit the Help Window press ESC or the F1 key again. 6.1.
PICOe-945GSE Half-Size CPU Card 6.2 Main The Main BIOS menu (BIOS Menu 1) appears when the BIOS Setup program is entered. 864H27 The Main menu gives an overview of the basic system information. BIOS Menu 1: Main System Overview The System Overview lists a brief summary of different system components. The fields in System Overview cannot be changed.
PICOe-945GSE Half-Size CPU Card o Size: Lists memory size The System Overview field also has two user configurable fields: System Time [xx:xx:xx] Use the System Time option to set the system time. Manually enter the hours, minutes and seconds. System Date [xx/xx/xx] Use the System Date option to set the system date. Manually enter the day, month and year. 6.
PICOe-945GSE Half-Size CPU Card BIOS Menu 2: Advanced 6.3.1 CPU Configuration Use the CPU Configuration menu (BIOS Menu 3) to view detailed CPU specifications 873H6 and configure the CPU.
PICOe-945GSE Half-Size CPU Card The CPU Configuration menu (BIOS Menu 3) lists the following CPU details: 837H Manufacturer: Lists the name of the CPU manufacturer Brand String: Lists the brand name of the CPU being used Frequency: Lists the CPU processing speed FSB Speed: Lists the FSB speed Cache L1: Lists the CPU L1 cache size Cache L2: Lists the CPU L2 cache size 6.3.
PICOe-945GSE Half-Size CPU Card Compatible Configures the on-board ATA/IDE controller to be in DEFAULT compatible mode. In this mode, a SATA channel will replace one of the IDE channels. This mode supports up to 4 storage devices. Configures the on-board ATA/IDE controller to be in Enhanced Enhanced mode. In this mode, IDE channels and SATA channels are separated. This mode supports up to 6 storage devices. Some legacy OS do not support this mode.
PICOe-945GSE Half-Size CPU Card The IDE Configuration menu (BIOS Menu 4) allows changes to the configurations for the 876H39 IDE devices installed in the system. If an IDE device is detected, and one of the above listed four BIOS configuration options are selected, the IDE configuration options shown in Section 6.3.2.1 appear. 87H40 6.3.2.
PICOe-945GSE Half-Size CPU Card Device: Lists the device type (e.g. hard disk, CD-ROM etc.) Type: Indicates the type of devices a user can manually select Vendor: Lists the device manufacturer Size: List the storage capacity of the device. LBA Mode: Indicates whether the LBA (Logical Block Addressing) is a method of addressing data on a disk drive is supported or not. Block Mode: Block mode boosts IDE drive performance by increasing the amount of data transferred.
PICOe-945GSE Half-Size CPU Card IDE disk drives on the specified channel. This option specifies an ATAPI Removable Media ARMD Device. These include, but are not limited to: ZIP LS-120 LBA/Large Mode [Auto] Use the LBA/Large Mode option to disable or enable BIOS to auto detects LBA (Logical Block Addressing). LBA is a method of addressing data on a disk drive. In LBA mode, the maximum drive capacity is 137 GB. BIOS is prevented from using the LBA mode control on Disabled the specified channel.
PICOe-945GSE Half-Size CPU Card PIO Mode [Auto] Use the PIO Mode option to select the IDE PIO (Programmable I/O) mode program timing cycles between the IDE drive and the programmable IDE controller. As the PIO mode increases, the cycle time decreases. Auto DEFAULT BIOS auto detects the PIO mode. Use this value if the IDE disk drive support cannot be determined. 0 PIO mode 0 selected with a maximum transfer rate of 3.3MBps 1 PIO mode 1 selected with a maximum transfer rate of 5.
PICOe-945GSE Half-Size CPU Card MWDMA0 Multi Word DMA mode 0 selected with a maximum data transfer rate of 4.2MBps MWDMA1 Multi Word DMA mode 1 selected with a maximum data transfer rate of 13.3MBps MWDMA2 Multi Word DMA mode 2 selected with a maximum data transfer rate of 16.6MBps UDMA1 Ultra DMA mode 0 selected with a maximum data transfer rate of 16.
PICOe-945GSE Half-Size CPU Card Auto DEFAULT BIOS auto detects HDD SMART support. Disabled Prevents BIOS from using the HDD SMART feature. Enabled Allows BIOS to use the HDD SMART feature 32Bit Data Transfer [Enabled] Use the 32Bit Data Transfer BIOS option to enables or disable 32-bit data transfers. Prevents the BIOS from using 32-bit data transfers. Disabled Enabled DEFAULT Allows BIOS to use 32-bit data transfers on supported hard disk drives. 6.3.
PICOe-945GSE Half-Size CPU Card Parallel Port Address [378] Use the Parallel Port Address option to select the parallel port base address. No base address is assigned to the Parallel Port Disabled 378 DEFAULT Parallel Port I/O port address is 378 278 Parallel Port I/O port address is 278 3BC Parallel Port I/O port address is 3BC Parallel Port Mode [Normal] Use the Parallel Port Mode option to select the mode the parallel port operates in.
PICOe-945GSE Half-Size CPU Card Parallel Port IRQ [IRQ7] Use the Parallel Port IRQ selection to set the parallel port interrupt address. IRQ5 is assigned as the parallel port interrupt address IRQ5 IRQ7 DEFAULT IRQ7 is assigned as the parallel port interrupt address Serial Port1 Address [3F8/IRQ4] Use the Serial Port1 Address option to select the Serial Port 1 base address.
PICOe-945GSE Half-Size CPU Card No base address is assigned to Serial Port 2 Disabled 2F8/IRQ3 DEFAULT Serial Port 2 I/O port address is 3F8 and the interrupt address is IRQ3 Serial Port 2 I/O port address is 3E8 and the interrupt 3E8/IRQ4 address is IRQ4 Serial Port 2 I/O port address is 2E8 and the interrupt 2E8/IRQ3 address is IRQ3 Serial Port2 Mode [Normal] Use the Serial Port2 Mode option to select the Serial Port2 operational mode.
PICOe-945GSE Half-Size CPU Card BIOS Menu 7: Hardware Health Configuration CPU FAN Mode Setting [Full On Mode] Use the CPU FAN Mode Setting option to configure the second fan. Full On Mode DEFAULT Automatic mode Fan is on all the time Fan is off when the temperature is low enough. Parameters must be set by the user. PWM Manual mode Pulse width modulation set manually When the CPU FAN Mode Setting option is in the Automatic Mode, the following parameters can be set. CPU Temp. Limit of OFF CPU Temp.
PICOe-945GSE Half-Size CPU Card When the CPU FAN Mode Setting option is in the PWM Manual Mode, the following parameters can be set. CPU Fan PWM control CPU Temp. Limit of OFF [000] WARNING: Setting this value too high may cause the fan to stop when the CPU is at a high temperature and therefore cause the system to be damaged. The CPU Temp. Limit of OFF option can only be set if the CPU FAN Mode Setting option is set to Automatic Mode. Use the CPU Temp.
PICOe-945GSE Half-Size CPU Card starts, it rotates using the starting pulse width modulation (PWM) specified in the Fan 3 Start PWM option below. To select a value, select the CPU Temp. Limit of Start option and enter a decimal number between 000 and 127. The temperature range is specified below. Minimum Value: 0°C Maximum Value: 127°C CPU Fan Start PWM [070] The Fan 3 Start PWM option can only be set if the CPU FAN Mode Setting option is set to Automatic Mode.
PICOe-945GSE Half-Size CPU Card The following system parameters and values are shown. The system parameters that are monitored are: System Temperatures: The following system temperatures are monitored o o CPU Temperature System Temperature Fan Speeds: The CPU cooling fan speed is monitored. o CPU Fan Speed Voltages: The following system voltages are monitored o o o o o o o o o CPU Core +1.05V +3.30V +5.00V +12.0 V +1.5V +1.8V 5VSB VBAT 6.3.
PICOe-945GSE Half-Size CPU Card BIOS Menu 8: Power Configuration 6.3.5.1 ACPI configuration The ACPI Configuration menu (BIOS Menu 9) configures the Advanced Configuration 80H4 and Power Interface (ACPI).
PICOe-945GSE Half-Size CPU Card BIOS Menu 9: ACPI Configuration Suspend Mode [S1(POS)] Use the Suspend Mode BIOS option to specify the sleep state the system enters when it is not being used. S1 (POS) DEFAULT System appears off. The CPU is stopped; RAM is refreshed; the system is running in a low power mode. S3 (STR) System appears off. The CPU has no power; RAM is in slow refresh; the power supply is in a reduced power mode. 6.3.
PICOe-945GSE Half-Size CPU Card BIOS Menu 10: Advanced Power Management Configuration Restore on AC Power Loss [Power On] Use the Restore on AC Power Loss BIOS option to specify what state the system returns to if there is a sudden loss of power to the system. The system remains turned off Power Off Power On The system turns on DEFAULT The system returns to its previous state. If it was on, it Last State turns itself on. If it was off, it remains off.
PICOe-945GSE Half-Size CPU Card suspend mode Resume on Keyboard/Mouse [Disabled] Use the Resume on Keyboard/Mouse BIOS option to enable activity on either the keyboard or mouse to rouse the system from a suspend or standby state. That is, the system is roused when the mouse is moved or a button on the keyboard is pressed.
PICOe-945GSE Half-Size CPU Card signal activity Enabled DEFAULT Wake event generated by PCI-Express WAKE# signal activity Resume On RTC Alarm [Disabled] Use the Resume On RTC Alarm option to specify the time the system should be roused from a suspended state.
PICOe-945GSE Half-Size CPU Card BIOS Menu 11: Remote Access Configuration [Advanced] Remote Access [Disabled] Use the Remote Access option to enable or disable access to the remote functionalities of the system. Disabled Enabled DEFAULT Remote access is disabled. Remote access configuration options shown below appear: Serial Port Number Serial Port Mode Redirection after BIOS POST Terminal Type These configuration options are discussed below.
PICOe-945GSE Half-Size CPU Card Serial Port Number [COM1] Use the Serial Port Number option allows to select the serial port used for remote access. COM1 DEFAULT System is remotely accessed through COM1 System is remotely accessed through COM2 COM2 NOTE: Make sure the selected COM port is enabled through the Super I/O configuration menu. Base Address, IRQ [3F8h,4] The Base Address, IRQ option cannot be configured and only shows the interrupt address of the serial port listed above.
PICOe-945GSE Half-Size CPU Card Disabled The console is not redirected after POST Boot Loader Redirection is active during POST and during Boot Loader Always DEFAULT Redirection is always active (Some OSes may not work if set to Always) Terminal Type [ANSI] Use the Terminal Type BIOS option to specify the remote terminal type. ANSI DEFAULT The target terminal type is ANSI VT100 The target terminal type is VT100 VT-UTF8 The target terminal type is VT-UTF8 6.3.
PICOe-945GSE Half-Size CPU Card USB Functions [Enabled] Use the USB Function option to enable or disable the USB controllers. USB controllers are enabled Disabled Enabled DEFAULT USB controllers are disabled USB 2.0 Controller [Enabled] The USB 2.0 Controller BIOS option enables or disables the USB 2.0 controller Enabled DEFAULT USB function enabled USB function disabled Disabled Legacy USB Support [Enabled] Use the Legacy USB Support BIOS option to enable USB mouse and USB keyboard support.
PICOe-945GSE Half-Size CPU Card The controller is capable of operating at full speed FullSpeed 12 Mb/s HiSpeed DEFAULT The controller is capable of operating at high speed 480 Mb/s 6.4 PCI/PnP Use the PCI/PnP menu (BIOS Menu 13) to configure advanced PCI and PnP settings. 84H WARNING: Setting wrong values for the BIOS selections in the PCIPnP BIOS menu may cause the system to malfunction.
PICOe-945GSE Half-Size CPU Card Use the IRQ# address to specify what IRQs can be assigned to a particular peripheral device. Available DEFAULT The specified IRQ is available to be used by PCI/PnP devices The specified IRQ is reserved for use by Legacy ISA Reserved devices Available IRQ addresses are: IRQ3 IRQ4 IRQ5 IRQ7 IRQ9 IRQ10 IRQ 11 IRQ 14 IRQ 15 DMA Channel# [Available] Use the DMA Channel# option to assign a specific DMA channel to a particular PCI/PnP device.
PICOe-945GSE Half-Size CPU Card DM Channel 3 DM Channel 5 DM Channel 6 DM Channel 7 6.5 Boot Use the Boot menu (BIOS Menu 14) to configure system boot options. 85H49 BIOS Menu 14: Boot 6.5.1 Boot Settings Configuration Use the Boot Settings Configuration menu (BIOS Menu 14) to configure advanced system 86H50 boot options.
PICOe-945GSE Half-Size CPU Card BIOS Menu 15: Boot Settings Configuration Quick Boot [Enabled] Use the Quick Boot BIOS option to make the computer speed up the boot process. No POST procedures are skipped Disabled Enabled DEFAULT Some POST procedures are skipped to decrease the system boot time Quiet Boot [Disabled] Use the Quiet Boot BIOS option to select the screen display when the system boots.
PICOe-945GSE Half-Size CPU Card AddOn ROM Display Mode [Force BIOS] The AddOn ROM Display Mode option allows add-on ROM (read-only memory) messages to be displayed. Force BIOS DEFAULT Allows the computer system to force a third party BIOS to display during system boot. Allows the computer system to display the Keep Current information during system boot. Bootup Num-Lock [On] The Bootup Num-Lock BIOS option allows the Number Lock setting to be modified during boot up.
PICOe-945GSE Half-Size CPU Card Can be booted from a remote system through the Enabled LAN Disabled DEFAULT Cannot be booted from a remote system through the LAN 6.5.2 Boot Device Priority Use the Boot Device Priority menu (BIOS Menu 16) to specify the boot sequence from 87H51 the available devices.
PICOe-945GSE Half-Size CPU Card 6.6 Security Use the Security menu (BIOS Menu 17) to set system and user passwords. 8H52 BIOS Menu 17: Security Change Supervisor Password Use the Change Supervisor Password to set or change a supervisor password. The default for this option is Not Installed. If a supervisor password must be installed, select this field and enter the password. After the password has been added, Install appears next to Change Supervisor Password.
PICOe-945GSE Half-Size CPU Card 6.7 Chipset Use the Chipset menu (BIOS Menu 18) to access the NorthBridge and SouthBridge 89H53 configuration menus WARNING! Setting the wrong values for the Chipset BIOS selections in the Chipset BIOS menu may cause the system to malfunction. BIOS Menu 18: Chipset 6.7.1 North Bridge Chipset Configuration Use the North Bridge Chipset Configuration menu (BIOS Menu 18) to configure the 890H54 Northbridge chipset settings.
PICOe-945GSE Half-Size CPU Card BIOS Menu 19:North Bridge Chipset Configuration Memory Hole [Disabled] The Memory Hole reserves the memory space between 15MB and 16MB for ISA expansion cards that require a specified area of memory to work properly. If an older ISA expansion card is used, please refer to the documentation that came with the card to see if it is necessary to reserve the space.
PICOe-945GSE Half-Size CPU Card Enable, 8MB DEFAULT 8MB of memory used by internal graphics device Boots Graphics Adapter Priority [PCI/IGD] Use the Boots Graphics Adapter option to select the graphics controller used as the primary boot device. Select either an integrated graphics controller (IGD) or a combination of PCI graphics controller, a PCI express (PEG) controller or an IGD. Configuration options are listed below: IGD PCI/IGD DEFAULT 6.7.1.
PICOe-945GSE Half-Size CPU Card DVMT/FIXED Memory Use the DVMT/FIXED Memory option to specify the maximum amount of memory that can be allocated as graphics memory. This option can only be configured for if DVMT Mode or Fixed Mode is selected in the DVMT Mode Select option. If Combo Mode is selected, the maximum amount of graphics memory is 128MB. Configuration options are listed below.
PICOe-945GSE Half-Size CPU Card BIOS Menu 20:SouthBridge Chipset Configuration Audio Controller [All Disabled] The Audio Controller option enables or disables the audio controller. Azalia Audio controller configured as Azalia AC’97 Audio Only The on-board AC’97 audio controller is enabled. All Disabled DEFAULT The on-board audio controller is disabled. Spread Spectrum [Disabled] Use the Spread Spectrum option to reduce the EMI.
PICOe-945GSE Half-Size CPU Card EMI reduced Enabled 6.8 Exit Use the Exit menu (BIOS Menu 21) to load default BIOS values, optimal failsafe values 893H56 and to save configuration changes. BIOS Menu 21:Exit Save Changes and Exit Use the Save Changes and Exit option to save the changes made to the BIOS options and to exit the BIOS configuration setup program.
PICOe-945GSE Half-Size CPU Card Discard Changes Use the Discard Changes option to discard the changes and remain in the BIOS configuration setup program. Load Optimal Defaults Use the Load Optimal Defaults option to load the optimal default values for each of the parameters on the Setup menus. F9 key can be used for this operation. Load Failsafe Defaults Use the Load Failsafe Defaults option to load failsafe default values for each of the parameters on the Setup menus. F8 key can be used for this operation.
PICOe-945GSE Half-Size CPU Card Chapter 7 7 Software Drivers Page 152
PICOe-945GSE Half-Size CPU Card 7.1 Available Software Drivers NOTE: The content of the CD may vary throughout the life cycle of the product and is subject to change without prior notice. Visit the IEI website or contact technical support for the latest updates. The following drivers can be installed on the system: Chipset VGA LAN Audio Installation instructions are given below. 7.2 Starting the Driver Program To access the driver installation programs, please do the following.
PICOe-945GSE Half-Size CPU Card Figure 7-1: Start Up Screen Step 3: Click PICOe-945GSE. Step 4: The screen in appears. Figure 7-2: Select Operating System Step 5: Select the operating system installed on the PICOe-945GSE system.
PICOe-945GSE Half-Size CPU Card manual describes the installation for a Windows XP operating system. Step 6: The list of drivers in Figure 7-3 appears. 85H Figure 7-3: Drivers 7.3 Chipset Driver Installation To install the chipset driver, please do the following. Step 1: Access the driver list shown in Figure 7-3. (See Section 7.2) 859H 860H Step 2: Click “1-Chipset Driver” Step 3: The setup files are extracted as shown in Figure 7-4.
PICOe-945GSE Half-Size CPU Card Figure 7-4: Chipset Driver Screen Step 4: When the setup files are completely extracted the Welcome Screen in Figure 862H 7-5 appears. Figure 7-5: Chipset Driver Welcome Screen Step 5: Click Next to continue.
PICOe-945GSE Half-Size CPU Card Step 6: The license agreement in Figure 7-6 appears. 863H Step 7: Read the License Agreement. Step 8: Click the Yes icon to continue. Figure 7-6: Chipset Driver License Agreement Step 9: The Read Me file in Figure 7-7 appears. 864H Step 10: Click Next to continue.
PICOe-945GSE Half-Size CPU Card Figure 7-7: Chipset Driver Read Me File Step 11: Setup Operations are performed as shown in Figure 7-8.
PICOe-945GSE Half-Size CPU Card Figure 7-8: Chipset Driver Setup Operations Step 12: Once the Setup Operations are complete, click the Next icon to continue. Step 13: The Finish screen appears. Step 14: Select “Yes, I want to restart the computer now” and click the Finish icon. See Figure 7-9.
PICOe-945GSE Half-Size CPU Card Figure 7-9: Chipset Driver Installation Finish Screen 7.4 VGA Driver Installation To install the VGA driver, please do the following. Step 1: Access the driver list shown in Figure 7-3. (See Section 7.2) 867H Step 2: Click “2-VGA” Step 3: The VGA Read Me file in Figure 7-10 appears. 869H Step 4: Click Next to continue.
PICOe-945GSE Half-Size CPU Card Figure 7-10: VGA Driver Read Me File Step 5: The installation files are extracted. See Figure 7-11. 870H Figure 7-11: VGA Driver Setup Files Extracted Step 6: The Welcome Screen in Figure 7-12 appears.
PICOe-945GSE Half-Size CPU Card Figure 7-12: VGA Driver Welcome Screen Step 7: Click Next to continue. Step 8: The license agreement in Figure 7-13 appears. 872H Step 9: Read the License Agreement. Step 10: Click the Yes icon to continue.
PICOe-945GSE Half-Size CPU Card Figure 7-13: VGA Driver License Agreement Step 11: The Read Me file in Figure 7-14 appears. 873H Step 12: Click Next to continue. Figure 7-14: VGA Driver Read Me File Step 13: Setup Operations are performed as shown in Figure 7-15.
PICOe-945GSE Half-Size CPU Card Figure 7-15: VGA Driver Setup Operations Step 14: Once the Setup Operations are complete, click the Next icon to continue. Step 15: The Finish screen appears. Step 16: Select “Yes, I want to restart the computer now” and click the Finish icon. See Figure 7-16.
PICOe-945GSE Half-Size CPU Card 7.5 LAN Driver Installation To install the chipset driver, please do the following. Step 1: Access the driver list shown in Figure 7-3. (See Section 7.2) 876H 87H Step 2: Click “3-LAN” Step 3: The Welcome screen in Figure 7-17 appears. 87H Figure 7-17: LAN Driver Welcome Screen Step 4: Click Next to continue. Step 5: The Ready to Install screen in Figure 7-18 appears. 879H Step 6: Click Next to proceed with the installation.
PICOe-945GSE Half-Size CPU Card Figure 7-18: LAN Driver Welcome Screen Step 7: The program begins to install. Step 8: The installation progress can be monitored in the progress bar shown in Figure 80H 7-19.
PICOe-945GSE Half-Size CPU Card Step 9: When the driver installation is complete, the screen in Figure 7-20 appears. 81H Figure 7-20: LAN Driver Installation Complete 7.6 Audio Driver Installation To install the chipset driver, please do the following. Step 1: Access the driver list shown in Figure 7-3. (See Section 7.2) 82H 83H Step 2: Click “4-Audio” Step 3: The screen in Figure 7-21 appears.
PICOe-945GSE Half-Size CPU Card Figure 7-21: Audio Driver Options 7.6.1 HD Audio Installation To install the HD Audio driver, please do the following: Step 1: Select “1-HDAudio” in Figure 7-21. 85H Step 2: Installation files are extracted as shown in Figure 7-22.
PICOe-945GSE Half-Size CPU Card Figure 7-22: Extract HD Audio Driver Installation Files Step 3: The Welcome screen in Figure 7-23 appears.
PICOe-945GSE Half-Size CPU Card Figure 7-23: HD Audio Driver Welcome Screen Step 4: Click Next to continue. Step 5: The system updates. See Figure 7-24.
PICOe-945GSE Half-Size CPU Card Figure 7-24: System Update Step 6: Follow the installation instructions until the HD Audio driver installation is complete.Step 0: 7.6.2 AC’97 Driver Installation To install the AC’97 audio driver, please do the following: Step 1: Select “2-AC’97” in Figure 7-21 89H Step 2: The installation files are extracted as shown in Figure 7-25.
PICOe-945GSE Half-Size CPU Card Figure 7-25: AC’97 Driver Installation File Extraction Step 3: The AC’97 Driver Installation screen in Figure 7-26 appears. 891H Step 4: Click Next to continue. Figure 7-26: AC’97 Driver Installation Welcome Screen Step 5: The Verification window in Figure 7-27 may appear. 892H Step 6: Click “Continue Anyway.
PICOe-945GSE Half-Size CPU Card Figure 7-27: AC’97 Driver Installation Verification Step 7: The driver installation begins. See Figure 7-28. 893H Figure 7-28: AC’97 Driver Installation Step 8: When the driver is installed, the driver installation finish screen in Figure 7-29 894H appears.
PICOe-945GSE Half-Size CPU Card Figure 7-29: AC’97 Driver Installation Complete Step 10: The system reboots.
PICOe-945GSE Half-Size CPU Card Appendix A A BIOS Menu Options Page 175
PICOe-945GSE Half-Size CPU Card System Overview......................................................................................... 111 32H 895H System Time [xx:xx:xx] .............................................................................. 112 32H 896H System Date [xx/xx/xx] ............................................................................... 112 324H 897H ATA/IDE Configurations [Compatible] ......................................................
PICOe-945GSE Half-Size CPU Card Power Button Mode [On/Off]...................................................................... 131 352H 925H Resume on Keyboard/Mouse [Disabled] .................................................. 132 35H 926H Resume on Ring [Disabled] ....................................................................... 132 354H 927H Resume on PCI-Express WAKE# [Enabled] ............................................. 132 35H 928H Resume On RTC Alarm [Disabled] .....................
PICOe-945GSE Half-Size CPU Card Internal Graphics Mode Select [Enable, 8MB].......................................... 146 38H 956H Boots Graphics Adapter Priority [PCI/IGD] .............................................. 147 384H 957H DVMT Mode Select [DVMT Mode] .............................................................. 147 385H 958H DVMT/FIXED Memory.................................................................................. 148 386H 95H Boot Display Device [CRT]..........................
PICOe-945GSE Half-Size CPU Card Appendix B B Terminology Page 179
PICOe-945GSE Half-Size CPU Card AC ’97 Audio Codec 97 (AC’97) refers to a codec standard developed by Intel® in 1997. ACPI Advanced Configuration and Power Interface (ACPI) is an OS-directed configuration, power management, and thermal management interface. AHCI Advanced Host Controller Interface (AHCI) is a SATA Host controller register-level interface. ATA The Advanced Technology Attachment (ATA) interface connects storage devices including hard disks and CD-ROM drives to a computer.
PICOe-945GSE Half-Size CPU Card computer is usually a male DE-9 connector. DAC The Digital-to-Analog Converter (DAC) converts digital signals to analog signals. DDR Double Data Rate refers to a data bus transferring data on both the rising and falling edges of the clock signal. DMA Direct Memory Access (DMA) enables some peripheral devices to bypass the system processor and communicate directly with the system memory.
PICOe-945GSE Half-Size CPU Card MAC The Media Access Control (MAC) protocol enables several terminals or network nodes to communicate in a LAN, or other multipoint networks. PCIe PCI Express (PCIe) is a communications bus that uses dual data lines for full-duplex (two-way) serial (point-to-point) communications between the SBC components and/or expansion cards and the SBC chipsets. Each line has a 2.5 Gbps data transmission rate and a 250 MBps sustained data transfer rate.
PICOe-945GSE Half-Size CPU Card asynchronous communications on the system and manages the system’s serial communication (COM) ports. UHCI The Universal Host Controller Interface (UHCI) specification is a register-level interface description for USB 1.1 Host Controllers. USB The Universal Serial Bus (USB) is an external bus standard for interfacing devices. USB 1.1 supports 12Mbps data transfer rates, while USB 2.0 supports 480Mbps data transfer rates.
PICOe-945GSE Half-Size CPU Card Appendix C C DIO Interface Page 184
PICOe-945GSE Half-Size CPU Card C.1 DIO Interface Introduction The DIO connector on the PICOe-945GSE is interfaced to GPIO ports on the ITE IT8718F Super I/O chipset. The DIO has both 4-bit digital inputs and 4-bit digital outputs. The digital inputs and digital outputs are generally control signals that control the on/off circuit of external devices or TTL devices. Data can be read or written to the selected address to enable the DIO functions.
PICOe-945GSE Half-Size CPU Card C.3 Assembly Language Samples C.3.1 Enable the DIO Input Function The BIOS interrupt call INT 15H controls the digital I/O. An assembly program to enable digital I/O input functions is listed below. MOV AX, 6F08H Sets the digital port as input INT 15H Initiates the INT 15H BIOS call C.3.2 Enable the DIO Output Function The BIOS interrupt call INT 15H controls the digital I/O. An assembly program to enable digital I/O output functions is listed below.
PICOe-945GSE Half-Size CPU Card Appendix D D Watchdog Timer Page 187
PICOe-945GSE Half-Size CPU Card NOTE: The following discussion applies to DOS environment. IEI support is contacted or the IEI website visited for specific drivers for more sophisticated operating systems, e.g., Windows and Linux. The Watchdog Timer is provided to ensure that standalone systems can always recover from catastrophic conditions that cause the CPU to crash. This condition may have occurred by external EMI or a software bug.
PICOe-945GSE Half-Size CPU Card NOTE: When exiting a program it is necessary to disable the Watchdog Timer, otherwise the system resets.
PICOe-945GSE Half-Size CPU Card Appendix E E Address Mapping Page 190
PICOe-945GSE Half-Size CPU Card E.
PICOe-945GSE Half-Size CPU Card Table E-1: IO Address Map Page 192
PICOe-945GSE Half-Size CPU Card E.2 IRQ Address Map Table E-2: IRQ Address Map E.
PICOe-945GSE Half-Size CPU Card Appendix F F Hazardous Materials Disclosure Page 194
PICOe-945GSE Half-Size CPU Card F.1 Hazardous Material Disclosure Table for IPB Products Certified as RoHS Compliant Under 2002/95/EC Without Mercury The details provided in this appendix are to ensure that the product is compliant with the Peoples Republic of China (China) RoHS standards. The table below acknowledges the presences of small quantities of certain materials in the product, and is applicable to China RoHS only.
PICOe-945GSE Half-Size CPU Card Part Name Toxic or Hazardous Substances and Elements Lead Mercury Cadmium Hexavalent Polybrominated Polybrominated (Pb) (Hg) (Cd) Chromium Biphenyls Diphenyl Ethers (CR(VI)) (PBB) (PBDE) Housing X O O O O X Display X O O O O X Printed Circuit X O O O O X X O O O O O X O O O O X Fan Assembly X O O O O X Power Supply X O O O O X O O O O O Board Metal Fasteners Cable Assembly Assemblies Battery O O: This tox
PICOe-945GSE Half-Size CPU Card 此附件旨在确保本产品符合中国 RoHS 标准。以下表格标示此产品中某有毒物质的含量符 合中国 RoHS 标准规定的限量要求。 本产品上会附有”环境友好使用期限”的标签，此期限是估算这些物质”不会有泄漏或突变”的 年限。本产品可能包含有较短的环境友好使用期限的可替换元件，像是电池或灯管，这些 元件将会单独标示出来。 部件名称 有毒有害物质或元素 铅 汞 镉 六价铬 多溴联苯 多溴二苯醚 (Pb) (Hg) (Cd) (CR(VI)) (PBB) (PBDE) 壳体 X O O O O X 显示 X O O O O X 印刷电路板 X O O O O X 金属螺帽 X O O O O O 电缆组装 X O O O O X 风扇组装 X O O O O X 电力供应组装 X O O O O X 电池 O O O O O O O: 表示该有毒有害物质在该部件所有物质材料中的含量均在 SJ/T11363-2006 标准规
