User guide

ManualsBrandsIEI Integration ManualsComputer AccessoriesRACK-360G

RACK-360G

4U Rackmount Chassis

Version: 1.0

Quick Installation Guide

RACK-360G QIG IEI Technology Corp. Page 1

ABOUT THE RACK-360G

AT/ATX compatible

to operate reliably in

rd 4U, 19” wide

ull-size, slot CPU cards

+ 1 x 3.5” HDD (hard disk

py disk drive)

 Dimens

: 0~40°C

midity: 5~95%

 Vibratio

o 5-17H mplitude displacement

o 1 40

The 4U, heavy-duty steel RACK-360G

rackmount industrial chassis is designed

industrial environments where it will be exposed to dust, wide

temperature variations, and shocks and vibrations, among other

things.

SPECIFICATIONS

 Form Factor: Standa

 SBC Form Factor: F

 Construction: Heavy-duty steel

 Slots Number: 14-slot (360G), 7-slot (360GAT

 Cooling(s): 1 x 12cm fan

 Drive Bay Combinations:

o 3 x 5.25” Optical drive

o 2 x 5.25” Optical drives

drive) + 1 x 3.5” FDD (flop

2 x 5.25” Optical drives + 2 x 3.5” FDDs

ions (DxWxH):

o 435.5mm x 431mm x 176mm

 Operating Temperature

 Relative Hu

z, 0.1” double a

7-6 Hz, 1.5G acceleration peak to peak

 Shock: 10G acceleration peak to peak

PACKING LIST

When you unpack the chassis, make sure the following

tems have been shipped.

 1 x Quick Installation Guide

 1 x Power Cord

 2 x Handles and handle plates

 1 x Screw Set

 2 x Keys

DETAILS OF INCLUDED SCREWS

The attached screw set includes five types of screws. Screws

used for chassis installation are shown below.

1 2 3 4 5

Peripherals/Parts Screw Labels in the Picture Above

5.25” Disk Drives 5

3.5” FDD 5

3.5” HDD 1

2.5” HDD 4

Power Supply Unit 1

Rackmount Bracket 3

3 Backplane

Table 1: Screws for Peripheral/Parts

Summary of content (9 pages)

PAGE 1
RACK-360G 4U Rackmount Chassis Version: 1.0 Quick Installation Guide Relative Humidity: 5~95% Vibration: o 5-17Hz, 0.1” double amplitude displacement o 17-640Hz, 1.5G acceleration peak to peak Shock: 10G acceleration peak to peak PACKING LIST When you unpack the chassis, make sure the following items have been shipped.
PAGE 2
DIMENSION DRAWING The dimensions of RACK-360G are shown on the diagram below. 431.00 320.00 176.00 176.00 I O 431.00 Figure 1: Dimension Drawing (measurement units: millimeter) RACK-360G QIG IEI Technology Corp.
PAGE 3
INSTALLATION STEPS To install the RACK-360G chassis, the following installation steps must be completed: STEP 3: TOP COVER AND HOLD-DOWN CLAMP REMOVAL STEP 3.1:REMOVE THE TOP COVER Step 1: Unpack the chassis. Step 2: Install the front handles. Step 3: Remove the top cover and hold-down clamp. The top cover is secured by a total of six screws, three on each side, of the chassis. Remove the screws and slide the cover toward the rear of the chassis. Step 4: Install the PSU (power supply unit).
PAGE 4
STEP 4: INSTALL THE POWER SUPPLY UNIT (PSU) Once the top cover and hold-down clamp have been removed, a user supplied PSU must be installed. Compatible IEI PSUs are listed in the table below. Model No. ACE-940AP-RS ACE-832AP-RS ACE-841AP-S-RS ACE-850AP-RS ACE-R4130AP-RS Input Type Watt AC AC AC AC AC AT ATX ATX ATX ATX 390W 300W 400W 500W 300W +3.3V N/A 28A 28A 27A 18A +5V 40A 30A 33A 29A 25A Output Range +12V1 +12V2 -5V 15A N/A 0.3A 15A N/A 0.3A 20A N/A 0.5A 18A 18A 0.3A 16A N/A 0.5A -12V 0.8A 0.
PAGE 5
To install the drives, please follow the steps outlined in the sections below. STEP 8.1: REMOVE THE SIDE BRACKET Before any drives can be installed, the side bracket attached to the main drive bracket must be removed. To remove the side bracket, remove the two retention screws from the top of the side bracket that secure the side bracket to the main bracket. Figure 8: Remove the Slot Cover Retention Screw Step 2: Slide the CPU card into the socket on the backplane reserved for the CPU card.
PAGE 6
Figure 11: Remove the Four Retention Screws STEP 8.4: INSTALL DRIVES INTO THE MAIN DRIVE BRACKET Figure 12: Remove the Front Metal Cover Retention Screws The main drive bracket has three bays that can support: o o o 3 x 5.25” Optical drives 2 x 5.25” Optical drives + 1 x 3.5” HDD 2 x 5.25” Optical drives + 1 x 3.5” FDD A 3.5” drive tray (HDD or FDD) is installed into the top drive bay. The two lower drive bays are covered with two metal plates. The 3.
PAGE 7
Step 2: Step 3: Place 3.5” HDD into the drive bracket. Make sure the PCB on the 3.5” HDD is placed directly on the bottom surface of the drive bracket and the 4-pin HDD power connector and IDE/SATA drive interface connector are facing the rear. Step 5: Secure the FDD to the drive bracket by inserting four retention screws (two on each side) through the sides of the drive bracket and into the HDD. Step 6: Reinsert the 3.5” drive tray, with the installed 3.5” FDD into the main drive bracket.
PAGE 8
1 Reset Switch cable 1 Step 1: Remove the chassis cover. (Refer to STEP 3: TOP COVER AND HOLD-DOWN CLAMP REMOVAl) Step 2: Unplug the power cable that is connected to the fan. Step 3: Remove the two retention screws at the top of the fan bracket. HDD LED cable 1 Power switch cable Table 4: Chassis Connectors Figure 16: Remove the Fan Bracket The pin definitions for the USB cable are shown below.
PAGE 9
Step 2: Replace the filter pad inside. Step 3: Slide the fan filter back into the chassis.Step 0: RACK-360G QIG IEI Technology Corp.