ROCKY-3786EV CPU Card MODEL NAME ROCKY-3786EV CPU Card IEI Technology Corp. MODEL: ROCKY-3786EV PICMG Socket 370 133 MHz FSB CPU Card with VGA, LAN, GbE, USB 2.0, Audio and SATA RAID User Manual Rev. 4.
ROCKY-3786EV CPU Card Revision Date Version Changes 25 September, 2009 4.10 Changed SATA chip to VIA VT6421A 28 September, 2006 4.
ROCKY-3786EV CPU Card MODEL NAME Table of Contents 1 INTRODUCTION........................................................................................................ 12 1.1 ROCKY-3786EV CPU BOARD OVERVIEW.............................................................. 13 1.1.1 ROCKY-3786EV Model Variations .................................................................. 13 1.1.2 ROCKY-3786EV CPU Board Applications...................................................... 13 1.1.
ROCKY-3786EV CPU Card 2.15 AUDIO CODEC ........................................................................................................ 29 2.16 POWER CONSUMPTION ........................................................................................... 30 2.17 PACKAGED CONTENTS AND OPTIONAL ACCESSORY ITEMS ..................................... 30 2.17.1 Package Contents........................................................................................... 30 2.17.2 Optional Accessory Items.....
ROCKY-3786EV CPU Card MODEL NAME 3.3.4 Keyboard/Mouse Connector ............................................................................ 60 3.3.5 VGA Connector ................................................................................................ 60 3.4 ONBOARD JUMPERS ................................................................................................. 62 3.4.1 Clear CMOS Jumper........................................................................................ 63 3.4.
ROCKY-3786EV CPU Card 5.1.2 Using Setup ...................................................................................................... 81 5.1.3 Getting Help..................................................................................................... 82 5.1.4 Unable to Reboot after Configuration Changes .............................................. 82 5.1.5 Main BIOS Menu ............................................................................................. 82 5.
ROCKY-3786EV CPU Card MODEL NAME List of Figures Figure 1-1 ROCKY-3786EV CPU Board Overview..................................................................14 Figure 2-1: Data Flow Block Diagram .........................................................................................24 Figure 3-1: Connector and Jumper Locations...........................................................................33 Figure 3-2: ATX Power Connector Location ...........................................................
ROCKY-3786EV CPU Card Figure 4-6: Connection of IDE Connector..................................................................................77 Figure 6-6: ATI Software Setup ................................................................................................ 121 Figure 6-7: ATI Software Setup Welcome ............................................................................... 122 Figure 6-8: License Agreement .................................................................................
ROCKY-3786EV CPU Card MODEL NAME List of Tables Table 1-1: ROCKY-3786EV Model Variations.............................................................................13 Table 1-2: Technical Specifications............................................................................................16 Table 2-1: Power Consumption...................................................................................................30 Table 3-1: Peripheral Interface Connectors .......................................
ROCKY-3786EV CPU Card Table 3-29: BIOS Protection Selection Jumper Settings..........................................................64 Table 3-30: Keyboard Power Selection Jumper Settings .........................................................64 Table 3-31: CF Mode Selection Jumper Settings ......................................................................65 Table 4-1: IEI Provided Cables ....................................................................................................
ROCKY-3786EV CPU Card MODEL NAME List of BIOS Menus BIOS Menu 1: Award BIOS CMOS Setup Utility ........................................................................83 BIOS Menu 2: Standard CMOS Features....................................................................................85 BIOS Menu 3: Advanced BIOS Features ....................................................................................90 BIOS Menu 4: Advanced Chipset Features.........................................................
ROCKY-3786EV CPU Card Chapter 1 1 Introduction Page 12 Page 12
MODEL NAME ROCKY-3786EV CPU Card 1.1 ROCKY-3786EV CPU Board Overview The PICMG form factor ROCKY-3786EV Pentium® III CPU platform is fully equipped with a high performance processor and advanced multi-mode I/Os. The ROCKY-3786EV is designed for system manufacturers, integrators, and VARs that want performance, reliability, and quality at a reasonable price. 1.1.1 ROCKY-3786EV Model Variations The ROCKY-3786EV has two model variations shown in Table 1-1.
ROCKY-3786EV CPU Card Complies with PICMG 1.0 Complies with RoHS Supports up to 133 MHz front side bus (FSB) Supports up to 512 MB SDRAM memory module Supports two SATA channels with transfer rates up to 150MB/s Optional high performance gigabit Ethernet (GbE) controller Optional USB 2.0 connectors 1.2 ROCKY-3786EV CPU Board Overview Figure 1-1 ROCKY-3786EV CPU Board Overview 1.2.
MODEL NAME ROCKY-3786EV CPU Card 1 x IrDA connector 1 x Keyboard/Mouse connector 1 x LAN LED connector 1 x Multi panel connector 1 x Parallel port connector 2 x SATA connectors 2 x Serial port connectors 2 x USB 1.1 connectors 4 x USB 2.
ROCKY-3786EV CPU Card Graphics Support On Chip Intel® 815E Memory Two PC 100/133 SDRAM memory modules (Max. 512MB) PCI Bus Interface 33MHz, Revision 2.2 Serial ATA (SATA) Two SATA connectors support RAID 0, 1 (VIA VT6421A Serial RAID controller) HDD Interface Two IDE channels supports four Ultra ATA 33/66/100 devices Floppy Disk Drive (FDD) Supports FDD USB Interfaces Two USB 1.1 connectors supported Four USB 2.
ROCKY-3786EV CPU Card MODEL NAME Chapter 2 2 Detailed Specifications Page 17 Page 17
ROCKY-3786EV CPU Card 2.1 CPU Support The ROCKY-3786EV CPU card has socket 370 and supports the following CPUs: Intel® Pentium® III (FC-PGA) processor, up to 1.4GHz Intel® Celeron® processor, 700MHz – 1.2GHz VIA C3 processor, 733MHz or above 2.1.1 Pentium® III The Intel® Pentium® III CPU comes with the following features: Available in 1.
ROCKY-3786EV CPU Card MODEL NAME Integrated high performance 16-KB instruction and 16-KB data, nonblocking, level one cache 256-KB Integrated Full Speed level two cache allows for low latency on read/store operations Double Quad Word Wide (256 bit) cache data bus provides extremely high throughput on read/store operations. 8-way cache associativity provides improved cache hit rate on reads/store operations.
ROCKY-3786EV CPU Card Plug-compatible with Socket 370 processors in terms of bus protocol, electrical interface, and physical package Software-compatible with thousands of x86 software applications available MMX-compatible instructions SSE-compatible instructions Two large (64-KB each, 4-way) on-chip caches (2-way in Stepping 8 and higher) 64-KB Level 2 victim cache (16-way) Two large TLBs (128 entries each, 8-way) Branch Target Address Cache with 1k entries each identifying 2 branches Unique and sophistica
ROCKY-3786EV CPU Card MODEL NAME Increased I/O bus bandwidth through the use of Intel Hub Architecture which allows better concurrency for next-generation embedded computing applications Support for 100 and 133 MHz SDRAM enabling cost effective high volume memory 512 MB maximum memory Low power sleep mode for energy savings Dual (815) or Quad (815E) USB ports Support for ATA/66 (815) or ATA/100 (815E) Integrated AC '97 Controller for cost effective audio and modem solutions Support (815E) Alert on LAN 1.
ROCKY-3786EV CPU Card o o 10/100 Mbit/sec Ethernet support 1 Mbit/sec HomePNA* support Integrated IDE Controller o o o o o Independent timing of up to 4 drives Ultra ATA/100/66/33, BMIDE and PIO modes Read transfers up to 100MB/s, Writes to 89 MB/s Separate IDE connections for Primary and Secondary cables Implements Write Ping-Pong Buffer for faster write performance USB o o o o 2 UHCI Host Controllers with a total of 4 ports USB 1.
ROCKY-3786EV CPU Card o o o o MODEL NAME ACPI Power Management Timer PCI PME# support SMI# generation All registers readable/restorable for proper resume from 0V suspend states o Support for APM-based legacy power management for non-ACPI implementations External Glue Integration o Integrated Pull-up, Pull-down and Series Termination resistors on IDE and processor interface Enhanced Hub I/F buffers improve routing flexibility (Not available with all Memory Controller Hubs) Firmware Hub (FWH) I/F sup
ROCKY-3786EV CPU Card 2.3 Data Flow Figure 2-1 shows the data flow between the two onboard chipsets and other components installed on the CPU board and described in the following sections of this chapter. Figure 2-1: Data Flow Block Diagram 2.4 Graphics Support The graphics features listed below are all integrated on the Intel 815E northbridge chipset.
ROCKY-3786EV CPU Card o o o o MODEL NAME Fogging Atmospheric Effects Z Buffering 3D Pipe 2D Clipping Backface Culling Digital Video Output o 85 MHz Flat Panel Monitor/Digital CRT Interface Or Digital Video Output for use with a external TV encoder Display o o o Integrated 24-bit 230 MHz RAMDAC Gamma Corrected Video DDC2B Compliant 2D Graphics o o Up to 1600x1200 in 8-bit Color at 85 Hz Refresh Hardware Accelerated Functions Arithmetic Stretch Blitter Video o o o o o o H/W Motion Compensation
ROCKY-3786EV CPU Card One PCI REQ/GNT pair can be given higher arbitration priority (intended for external 1394 host controller) 2.7 10/100/1000Mbps Ethernet The onboard Intel 82562ET controller (for ROCKY-3786EV) provides 10/100 Base-T Internet connectivity to the system. The Intel 82562ET controller features are below. IEEE 802.3 10BASE-T/100BASE-TX compliant physical layer interface IEEE 802.
ROCKY-3786EV CPU Card MODEL NAME 2.8 Drive Interfaces The ROCKY-3786EV can support the following drive interfaces. 2 x SATA drives 2 x IDE devices 1 x FDD 1 x Compact Flash (CF) Card 2.8.1 SATA Drives The ROCKY-3786EV CPU Board supports two first generation SATA drives with transfer rates up to 150MB/s via VIA VT6421A Serial RAID controller. The two SATA connectors also support RAID 0, 1. 2.8.
ROCKY-3786EV CPU Card 2.9 Serial Ports The ROCKY-3786EV CPU board has two high-speed UART serial ports, configured as CN2 and CN8. The serial ports have the following specifications. 16C550 UART with 16-byte FIFO buffer 115.2Kbps transmission rate 2.10 Real Time Clock 256-byte battery backed CMOS RAM 2.11 Infrared Data Association (IrDA) Interface The ROCKY-3786EV CPU Board IrDA supports the following interfaces.
ROCKY-3786EV CPU Card MODEL NAME Minimum Operating Temperature: 0ºC (32°F) Maximum Operating Temperature: 60°C (140°F) A cooling fan and heat sink must be installed on the CPU. Thermal paste must be smeared on the lower side of the heat sink before it is mounted on the CPU. Heat sinks are also mounted on the northbridge and southbridge chipsets to ensure the operating temperature of these chips remain low. 2.15 Audio Codec The ROCKY-3786EV has an integrated REALTEK ALC655 CODEC.
ROCKY-3786EV CPU Card Adjustable VREFOUT control Supports 48KHz S/PDIF output, complying with AC'97 Rev 2.3 specifications Supports 32K/44.1K/48KHz S/PDIF input Power support: Digital: 3.3V; Analog: 3.3V/5V Standard 48-pin LQFP package EAX™ 1.0 & 2.0 compatible Direct Sound 3D™ compatible A3D™ compatible I3DL2 compatible HRTF 3D positional audio 10-band software equalizer Voice cancellation and key shifting in Karaoke mode 2.
ROCKY-3786EV CPU Card MODEL NAME 1 x Keyboard/ PS2 mouse Y cable 1 x Mini jumper pack 1 x QIG (quick installation guide) 1 x Utility CD 2.17.2 Optional Accessory Items The items shown in the list below are optional accessory items purchased separately.
ROCKY-3786EV CPU Card Chapter 3 3 Connectors and Jumpers Page 32 Page 32
MODEL NAME ROCKY-3786EV CPU Card 3.1 Peripheral Interface Connectors The locations of the peripheral interface connectors are shown in Section 3.1.1. A complete list of all the peripheral interface connectors can be seen in Section 3.1.2. 3.1.1 ROCKY-3786EV CPU Board Layout Figure 3-1 shows the onboard peripheral connectors, backplane peripheral connectors and onboard jumpers. Figure 3-1: Connector and Jumper Locations 3.1.
ROCKY-3786EV CPU Card CPU fan connector (1) 3-pin header FAN2 CPU fan connector (2) 3-pin header FAN3 CRT connector 10-pin header CN26 SDRAM slot (1) 168-pin slot DIMM0 SDRAM slot (2) 168-pin slot DIMM1 FDD connector 34-pin header CN3 IDE Interface connector (Primary) 40-pin header CN1 IDE Interface connector (Secondary) 40-pin header CN7 IrDA connector 5-pin header CN4 Keyboard connector 5-pin header CN22 LAN LED connector 8-pin header CN12 Multi Panel connector 14-pin hea
MODEL NAME ROCKY-3786EV CPU Card 3.1.3 Rear Panel Connectors Table 3-2 lists the rear panel connectors on the ROCKY-3786EV CPU card. Detailed descriptions of these connectors can be found in Section 3.3. Connectors Type Label Audio Line Out connector LINE OUT CN16 10/100Mbps Ethernet connector RJ-45 LAN1 Optional 1Gb Ethernet connector RJ-45 LAN2 Keyboard/Mouse connector PS/2 CN23 VGA connector 15-pin VGA connector CN11 Table 3-2: Peripheral Interface Connectors 3.1.
ROCKY-3786EV CPU Card 3.2 Internal Peripheral Connectors Internal peripheral connectors are found on the CPU card and are only accessible when the CPU board is outside of the chassis. This section has complete descriptions of all the internal, peripheral connectors on the ROCKY-3786EV CPU board. 3.2.
ROCKY-3786EV CPU Card MODEL NAME Figure 3-2: ATX Power Connector Location 3.2.2 ATX Power 5VSB and PSON connector CN Label: CN20 CN Type: 3-pin header CN Location: See Figure 3-3 CN Pinouts: See Table 3-5 PIN NO.
ROCKY-3786EV CPU Card Figure 3-3: ATX Power 5VSB and PSON Connector Location 3.2.3 ATX Power Switch Connector CN Label: CN5 CN Type: 2-pin header CN Location: See Figure 3-4 CN Pinouts: See Table 3-6 The ATX power switch connector supports ATX power switch and enables power on/off from the chassis. PIN NO.
ROCKY-3786EV CPU Card MODEL NAME Figure 3-4: ATX Power Switch Connector Location 3.2.4 Audio Connector CN Label: CN28 CN Type: 12-pin header (2x6) CN Location: See Figure 3-5 CN Pinouts: See Table 3-7 The ROCKY-3786EV has a built-in AC ’97 AUDIO CODEC connector directly connected to the SPEAKER-OUT, MIC-IN, LINE-IN and LINE-OUT. PIN NO.
ROCKY-3786EV CPU Card 10 GROUND (NO USE) 11 MIC IN 12 GROUND (FOR MIC IN CONNECTOR) Table 3-7: Audio Connector Pinouts Figure 3-5: Audio connector Location 3.2.5 CD In Connector CN Label: CN27 CN Type: 4-pin header CN Location: See Figure 3-6 CN Pinouts: See Table 3-8 This 4-pin header connects to audio sources such as CD/DVD-ROM optical drives. PIN NO.
MODEL NAME ROCKY-3786EV CPU Card 4 CD Right Table 3-8: CD In Connector Pinouts Figure 3-6: CD In Connector Location 3.2.6 Compact Flash Socket CN Label: CN25 CN Type: 50-pin header (2x25) CN Location: See Figure 3-7 CN Pinouts: See Table 3-9 A compact flash memory module is inserted to the Compact Flash connector (CF1). Jumper 2 (JP2) configures the compact flash drive as either a slave or master device. PIN NO. DESCRIPTION PIN NO.
ROCKY-3786EV CPU Card 9 GROUND 34 IOR# 10 N/C 35 IOW# 11 N/C 36 OBLIGATORY TO PULL HIGH 12 N/C 37 IRQ15 13 VCC 38 VCC 14 N/C 39 MASTER/SLAVE 15 N/C 40 N/C 16 N/C 41 RESET# 17 N/C 42 IORDY 18 A2 43 N/C 19 A1 44 OBLIGATORY TO PULL HIGH 20 A0 45 ACTIVE# 21 D0 46 PDIAG# 22 D1 47 D8 23 D2 48 D9 24 N/C 49 D10 25 CARD DETECT2 50 GROUND Table 3-9: CFII Socket Pinouts Figure 3-7: CFII Socket Location Page 42 Page 42
ROCKY-3786EV CPU Card MODEL NAME 3.2.7 CPU Fan Connector CN Label: FAN2 and FAN3 CN Type: 3-pin header CN Location: See Figure 3-8 CN Pinouts: See Table 3-10 The CPU fan connector provides a 12V/500mA to the cooling fan. The connector has a "rotation" pin to get rotation signals from the fan and notify the system so the system BIOS can recognize the fan speed. Please note that only certain fans can issue the rotation signals. PIN NO.
ROCKY-3786EV CPU Card 3.2.8 CRT Connector CN Label: CN26 CN Type: 10-pin header (2x5) CN Location: See Figure 3-10 CN Pinouts: See Table 3-12 PIN NO. DESCRIPTION PIN NO. DESCRIPTION 1 RED 2 DDCCLK 3 GREEN 4 DDC DAT 5 BLUE 6 GROUND 7 HSYNC 8 GROUND 9 VSYNC 10 GROUND Table 3-11: CRT Connector Pinouts Figure 3-9: CRT Connector Location 3.2.
MODEL NAME ROCKY-3786EV CPU Card The ROCKY-3786EV is shipped with a 34-pin daisy-chain drive connector cable. This cable can be connected to the FDD connector. PIN NO. DESCRIPTION PIN NO.
ROCKY-3786EV CPU Card Figure 3-10: FDD Connector Location 3.2.10 IDE Interface Connectors CN Label: CN1 (primary) and CN7 (secondary) CN Type: 40-pin header (2x20) CN Location: See Figure 3-11 CN Pinouts: See Table 3-13 Two IDE connectors provide connectivity for four IDE devices.
MODEL NAME ROCKY-3786EV CPU Card PIN NO. DESCRIPTION PIN NO.
ROCKY-3786EV CPU Card Figure 3-11: IDE Interface Connector Locations 3.2.11 IrDA Connector CN Label: CN4 CN Type: 5-pin header CN Location: See Figure 3-12 CN Pinouts: See Table 3-14 The integrated IrDA connector supports both the SIR and ASKIR infrared protocols. PIN NO.
ROCKY-3786EV CPU Card MODEL NAME Figure 3-12: IrDA Connector Location 3.2.12 Keyboard Connector CN Label: CN22 CN Type: 5-pin header CN Location: See Figure 3-13 CN Pinouts: See Table 3-15 For alternative applications, an on board keyboard pin header connector is also available. PIN NO.
ROCKY-3786EV CPU Card Figure 3-13: Keyboard Connector Location 3.2.13 LAN LED Connector CN Label: CN12 CN Type: 8-pin header CN Location: See Figure 3-14 CN Pinouts: See Table 3-16 Use the LAN LED connector to connect the LAN status and activity LEDs. PIN NO. DESCRIPTION PIN NO. DESCRIPTION 1 100ACT+ 2. 100ACT- 3 100LINK+ 4. 100LINK- 5. 1G_ACT+ 6. 1G_ACT- 7. 1G_ LINK+ 8.
MODEL NAME ROCKY-3786EV CPU Card Figure 3-14: LAN LED Connector Location 3.2.14 Multi Panel Connector CN Label: CN24 CN Type: 14-pin header (2x7) CN Location: See Figure 3-15 CN Pinouts: See Table 3-17 The Multi Panel connector provides connectivity to several external switches and indicators for monitoring and controlling the CPU board. PIN NO. DESCRIPTION PIN NO. DESCRIPTION 1. POWER-LED + 2 SPEAKER - 3. N/C 4 N/C 5. POWER-LED - 6 N/C 7. N/C 8 SPEAKER +5V 9.
ROCKY-3786EV CPU Card Figure 3-15: Multi Panel Connector Location 3.2.15 Parallel Port Connector CN Label: CN9 CN Type: 26-pin header (2x13 pins) CN Location: See Figure 3-16 CN Pinouts: See Table 3-18 The parallel port is connected to a printer or other parallel device with a 26-pin flat-cable connector. PIN NO. DESCRIPTION PIN NO.
MODEL NAME ROCKY-3786EV CPU Card 17 PRINTER SELECT LN# 18 GROUND 19 GROUND 20 GROUND 21 GROUND 22 GROUND 23 GROUND 24 GROUND 25 GROUND 26 NC Table 3-18: Parallel Port Connector Pinouts Figure 3-16: Parallel Port Connector Location 3.2.16 SATA Drive Ports CN Label: CN29, CN30 CN Type: 7-pin port CN Location: See Figure 3-17 CN Pinouts: See Table 3-19 The SATA drive ports provide connectivity to SATA drives with a maximum data transfer rate of 150MB/s.
ROCKY-3786EV CPU Card PIN NO. DESCRIPTION PIN NO. DESCRIPTION 1 GND 5 RX- 2 TX+ 6 RX+ 3 TX- 7 GND 4 GND Table 3-19: SATA Connector Pinouts Figure 3-17: SATA Connector Locations 3.2.17 Serial Port Connectors CN Label: CN2, CN8 CN Type: 10-pin headers (2x5 pins) CN Location: See Figure 3-18 CN Pinouts: See Table 3-20 The CN2 and CN8 serial port connectors connect to RS-232 serial port devices.
MODEL NAME ROCKY-3786EV CPU Card PIN DESCRIPTION PIN DESCRIPTION 1 DATA CARRIER DETECT (DCD) 6 DATA SET READY (DSR) 2 RECEIVE DATA (RXD) 7 REQUEST TO SEND (RTS) 3 TRANSMIT DATA (TXD) 8 CLEAR TO SEND (CTS) 4 DATA TERMINAL READY (DTR) 9 RING INDICATOR (RI) 5 GND (GND) 10 NC Table 3-20: Serial Port Connector Pinouts Figure 3-18 Serial Port Connector Locations 3.2.18 Internal USB 1.
ROCKY-3786EV CPU Card PIN NO. DESCRIPTION PIN NO. DESCRIPTION 1 VCC 2 GND 3 DATA1- 4 DATA1+ 5 DATA2+ 6 DATA2- 7 GND 8 VCC Table 3-21: Internal USB 1.1 Connector Pinouts Figure 3-19: Internal USB 1.1 Connector Location 3.2.19 Optional USB 2.0 Connectors CN Label: USB1, USB2 CN Type: 8-pin header (2x4 pins) CN Location: See Figure 3-20 CN Pinouts: See Table 3-22 Two 2x4 pin connectors provide connectivity to four USB 2.0 ports. The USB ports are used for I/O bus expansion.
MODEL NAME ROCKY-3786EV CPU Card PIN NO. DESCRIPTION PIN NO. DESCRIPTION 1 VCC 2 DATA1- 3 DATA1+ 4 GND 5 VCC 6 DATA2- 7 DATA2+ 8 GND Table 3-22: Optional USB 2.0 Connector Pinouts Figure 3-20: Optional USB 2.0 Connector Locations 3.3 External (Rear Panel) Connectors Figure 3-21 shows the ROCKY-3786EV CPU board rear panel. The peripheral connectors on the back panel can be connected to devices externally when the CPU card is installed in a chassis.
ROCKY-3786EV CPU Card Figure 3-21: ROCKY-3786EV CPU Board Rear Panel 3.3.1 Audio Line Out Connector CN Label: CN16 CN Location: See Figure 3-21 (labeled number 4) CN Pinouts: See Table 3-23 Connect an audio device to the line out connector on the rear panel Figure 3-21 (labeled number 4). PIN NO. DESCRIPTION 1 GROUND 2 LEFT SIGNAL 3 NC 4 RIGHT SIGNAL 5 NC Table 3-23: Line Out Connector Pinouts 3.3.
MODEL NAME ROCKY-3786EV CPU Card The 10/100Mbps connection can be made between the Ethernet connectors and a Local Area Network (LAN) through a network hub. An RJ-45 Ethernet connector is shown in Figure 3-22. PIN NO. DESCRIPTION PIN NO. DESCRIPTION 1 TX+ 5. N/C 2 TX- 6. RX- 3. RX+ 7. N/C 4. N/C 8. N/C Table 3-24: 10/100Mbps Ethernet Connector Pinouts Figure 3-22: Ethernet Connector 3.3.
ROCKY-3786EV CPU Card PIN NO. DESCRIPTION PIN NO. DESCRIPTION 1 TXA+ ( TX+ ) 5. TXC-( N/C ) 2 TXA-( TX- ) 6. TXB-( RX- ) 3. TXB+( RX+ ) 7. TXD+( N/C ) 4. TXC+( N/C ) 8. TXD-( N/C ) Table 3-25: Optiona 1Gb Ethernet Connector Pinouts 3.3.4 Keyboard/Mouse Connector CN Label: CN23 CN Type: PS/2 CN Location: See Figure 3-21 (labeled number 1) CN Pinouts: See Table 3-26 The PS/2 mouse and keyboard connectors are connected to a mouse and a keyboard. PIN NO. DESCRIPTION PIN NO.
MODEL NAME ROCKY-3786EV CPU Card CN Location: See Figure 3-21 (labeled number 5) The standard 15-pin VGA connector connects to a CRT or LCD display monitor. PIN NO. DESCRIPTION PIN NO.
ROCKY-3786EV CPU Card 3.4 Onboard Jumpers NOTE: A jumper is a metal bridge that is used to close an electrical circuit. It consists of two metal pins and a small metal clip (often protected by a plastic cover) that slides over the pins to connect them. To CLOSE/SHORT a jumper means connecting the pins of the jumper with the plastic clip and to OPEN a jumper means removing the plastic clip from a jumper. Figure 3-25 Jumper The ROCKY-3786EV CPU Board has four onboard jumpers. See Table 3-3.
MODEL NAME ROCKY-3786EV CPU Card 3.4.1 Clear CMOS Jumper Jumper Label: JP1 Jumper Type: 3-pin header Jumper Settings: See Table 3-28 Jumper Location: See Figure 3-26 If the CPU Card fails to boot due to improper BIOS setting, use this jumper to clear the CMOS data and reset the system BIOS information. To do this, use the jumper cap to close pins 2 and 3 for a few seconds then reinstall the jumper clip back to pins 1 and 2.
ROCKY-3786EV CPU Card Jumper Location: See Figure 3-26 Use the jumper cap to close pins 2 and 3 of the JP2 jumper to protect BIOS from writing. JP2 BIOS Protection 2-3 closed Locked (default) 1-2 closed Unlocked Table 3-29: BIOS Protection Selection Jumper Settings 3.4.3 Keyboard Power Selection Jumper Jumper Label: JP4 Jumper Type: 3-pin header Jumper Settings: See Table 3-30 Jumper Location: See Figure 3-26 This jumper allows the user to set the keyboard power.
ROCKY-3786EV CPU Card JP3 CF Mode Open SLAVE (default) Closed MASTER MODEL NAME Table 3-31: CF Mode Selection Jumper Settings Page 65 Page 65
ROCKY-3786EV CPU Card Page 66 Page 66
ROCKY-3786EV CPU Card MODEL NAME Chapter 4 4 Installation and Configuration Page 67 Page 67
ROCKY-3786EV CPU Card 4.1 Installation Considerations NOTE: The following installation notices and installation considerations should be read and understood before the motherboard is installed. All installation notices pertaining to the installation of the motherboard should be strictly adhered to. Failing to adhere to these precautions may lead to severe damage of the motherboard and injury to the person installing the motherboard. 4.1.
ROCKY-3786EV CPU Card MODEL NAME Use the product before verifying all the cables and power connectors are properly connected. Allow screws to come in contact with the PCB circuit, connector pins, or its components. 4.2 Unpacking NOTE: If any of the items listed below are missing when the ROCKY-3786EV is unpacked, do not proceed with the installation. Contact the ROCKY-3786EV reseller or vendor. 4.2.
ROCKY-3786EV CPU Card 1 x ATA66/100 flat cable 2 x SATA cables 1 x SATA power cable 1 x RS232 cable 1 x USB cable 1 x Keyboard/ PS2 mouse Y cable 1 x Mini jumper pack 1 x QIG (Quick Installation Guide) 1 x Utility CD If any of these items are missing, please contact the CPU card reseller or vendor and do not proceed any further with the installation. 4.3 ROCKY-3786EV CPU Card Installation WARNING: Never run the motherboard without the appropriate heat sinks and coolers.
ROCKY-3786EV CPU Card MODEL NAME ROCKY-3786EV always take anti-static precautions in order to prevent ESD damage to the motherboard and other electronic components like the CPU and DIMM modules. The following components must be installed onto the ROCKY-3786EV or connected to the ROCKY-3786EV during the installation process. CPU CPU cooling kit DIMM modules Peripheral device connection 4.3.1 CPU Installation WARNING: CPUs are expensive and sensitive components.
ROCKY-3786EV CPU Card Step 1: Inspect the CPU socket. Make sure there are no bent pins and make sure the socket contacts are free of foreign material. If any debris is found, remove it with compressed air. Step 2: Open the CPU socket lever. Disengage the load lever by pressing the lever down and slightly outward to clear the retention tab. Rotate the load lever to a fully open position. (See Figure 4-1) Step 3: Orientate the CPU properly. Make sure the IHS (Integrated Heat Sink) side is facing upward.
ROCKY-3786EV CPU Card MODEL NAME CF-504-RS CF-507-RS CF-512-RS CF-513-RS Figure 4-2: IEI Socket 370 Cooling Kits NOTE: The heat sink comes with a sprayed layer of thermal paste. Do not accidentally wipe away the thermal paste while unpacking or installing the heat sink. Thermal paste between the CPU and the heat sink is important for optimum heat dissipation. To install the cooling kit, please follow the steps below. Step 1: Properly orient the cooling kit.
ROCKY-3786EV CPU Card Step 3: Secure the cooling kit in place. Gently push the levered mounting clip down with a slight inward movement to snap it into place under the connecting tab. (See Figure 4-3) Step 4: Connect the fan cable. Connect the cooling kit fan cable to the fan connector on the CPU card. Carefully route the cable and avoid heat generating chips and fan blades.Step 0: Figure 4-3: Install the CPU cooler 4.3.3 DIMM Module Installation 4.3.3.
ROCKY-3786EV CPU Card MODEL NAME When purchasing the DIMM modules, make sure the modules are compatible with the DIMM slot specified in Section 2.5 Memory Support. 4.3.3.2 DIMM Module Installation The ROCKY-3786EV CPU card has two SDRAM DIMM socket. Follow the steps below to install the DIMM module. Step 1: Make sure the two handles of the DIMM socket are in the "open" position, leaning outward (Figure 4-4).
ROCKY-3786EV CPU Card Figure 4-5: Locking the DIMM Module Step 3: To remove the memory module, push both handles outward, and the memory module is ejected by the mechanism in the socket.Step 0: 4.3.4 Peripheral Device Connection Cables provided by IEI that connect peripheral devices to the CPU card are listed in Table 4-1. Cables not included in the kit must be purchased separately.
ROCKY-3786EV CPU Card MODEL NAME 4.3.4.2 IDE Disk Drive Connector (CN1, CN7) The cable used to connect the CPU card to an IDE HDD is a standard 40-pin ATA66/100 flat cable. Follow the instructions below to connect an IDE HDD to the CPU card. Step 1: Find the ATA66/100 flat cable in the kit that came with the CPU card. Step 2: Connect one end of the cable to the IDE1 connector on the CPU card. A keyed pin on the IDE connectors prevents them from being connected incorrectly.
ROCKY-3786EV CPU Card Step 1: Plug the 26-pin FPC-cable connector into CN34. Make sure that the red wire corresponds to pin one on the connector. Step 2: Attach the appropriate connector on the other end of the cable to the floppy drive. Only one connector in the set can be used.Step 0: 4.3.4.4 Parallel Port Connector (CN9) The onboard parallel port connector (CN9) connects to a printer. The ROCKY-3786EV comes with a multi-mode (ECP/EPP/SPP) parallel port.
ROCKY-3786EV CPU Card MODEL NAME 4.5 Rear Panel Connectors 4.5.1 Ethernet Connection The rear panel RJ-45 connectors can be connected to an external LAN and communicate with data transfer rates up to 1Gb/s. 4.5.2 Keyboard and Mouse Connection A PS/2 keyboard and a PS/2 mouse can be connected to the appropriate PS/2 connector on the rear panel. 4.5.3 VGA Connection The conventional CRT monitor connector (CN11) is a 15-pin, female D-SUB connector. It can be connected to an external monitor.
ROCKY-3786EV CPU Card Chapter 5 5 Award BIOS Setup Page 80 Page 80
ROCKY-3786EV CPU Card MODEL NAME 5.1 Introduction A licensed copy of Phoenix Award BIOS is preprogrammed into the ROM BIOS. The BIOS setup program allows users to modify the basic system configuration. This chapter describes how to access the BIOS setup program and the configuration options that may be changed. 5.1.1 Starting Setup The Phoenix Award BIOS is activated when the computer is turned on. The setup program can be activated in one of two ways. 1.
ROCKY-3786EV CPU Card F6 Fail-safe defaults for the current page menu items F7 Optimized defaults for the current page menu items F9 Menu in BIOS F10 Save changes and Exit BIOS Table 5-1: BIOS Navigation Keys 5.1.3 Getting Help When F1 is pressed a small help window describing the appropriate keys to use and the possible selections for the highlighted item appears. To exit the Help Window press ESC or the F1 key again. 5.1.
ROCKY-3786EV CPU Card MODEL NAME BIOS Menu 1: Award BIOS CMOS Setup Utility NOTE: The following sections completely describe the menus listed below and the configuration options available to users. The following menu options are seen in “BIOS Menu 1”. Standard CMOS Features: Changes the basic system configuration. Advanced BIOS Features: Changes the advanced system settings. Advanced Chipset Features: Changes the chipset configuration features.
ROCKY-3786EV CPU Card The following user configurable options are also available in BIOS Menu 1: Load Fail-Safe Defaults Use the Load Fail-Safe Defaults option to load failsafe default values for each BIOS parameter in the setup menus. Press F6 for this operation on any page. Load Optimized Defaults Use the Load Optimized Defaults option to load optimal default values for each BIOS parameter in the setup menus. Press F7 for this operation on any page.
MODEL NAME ROCKY-3786EV CPU Card Exit Without Saving Use the Exit Without Saving option to exit the BIOS menus without saving any configuration changes. 5.2 Standard CMOS Features Use the Standard CMOS Features BIOS menu (BIOS Menu 2) to set basic BIOS configuration options. BIOS Menu 2: Standard CMOS Features Date [Day mm:dd:yyyy] Use the Date option to set the system date. Time [hh/mm/ss] Use the Time option to set the system time.
ROCKY-3786EV CPU Card IDE Master and IDE Slave When entering setup, BIOS auto detects the presence of IDE devices. The Standard CMOS Features menu shows the status of the auto detected IDE devices. The following IDE devices are detected and shown in the Standard CMOS Features menu: IDE Primary Master IDE Primary Slave IDE Secondary Master IDE Secondary Slave IDE device configurations are changed or set in the IDE Configuration menu.
MODEL NAME ROCKY-3786EV CPU Card Halt On [All, But Keyboard] Use the Halt On option to specify what errors detected during the power up process stop the system. Whenever BIOS detects a non-fatal error the All Errors system is stopped and the user prompted. The system boot is not stopped for any errors No Errors that may be detected. All, But Keyboard (Default) The system boot does not stop for a keyboard error; it stops for all other errors.
ROCKY-3786EV CPU Card 5.2.1 IDE Primary Master/Slave Use the IDE Primary Master/Slave menu to set or change the master/slave IDE configurations. IDE HDD Auto-Detection [Press Enter] Use the IDE HDD Auto-Detection option to enable BIOS to automatically detect the IDE settings. Select IDE HDD Auto-Detection and press ENTER. BIOS automatically detects the HDD type. Do not set this option manually.
ROCKY-3786EV CPU Card MODEL NAME CHS Select this mode if the HDD capacity is less than 504MB. Select this mode if the HDD capacity is more than LBA 8.4GB. This mode is an extended ECHS mode and while it Large supports HDDs larger than 504MB, it is not recommended. Auto (Default) If you are unsure of what access mode to set, select this option. Capacity The Capacity specification indicates the storage capacity of the HDD installed in the system.
ROCKY-3786EV CPU Card Sector The Sector specification indicates how many logical sectors the HDD has been divided into. 5.3 Advanced BIOS Features Use the Advanced BIOS Features menu (BIOS Menu 3) to configure the CPU and peripheral device configuration options. BIOS Menu 3: Advanced BIOS Features Virus Warning [Disabled] NOTE: Many disk diagnostic programs can cause the above warning message to appear when the program attempts to access the boot sector table.
MODEL NAME ROCKY-3786EV CPU Card recommended that the virus protection function be disabled before running such a program. Use the Virus Warning option to enable BIOS to monitor the boot sector and partition table of the HDD for any attempted modification. If a modification attempt is made, the BIOS halts the system and an error message appears. If necessary, an anti-virus program can then be run to locate and remove the virus before any damage is done.
ROCKY-3786EV CPU Card Quick Power On Self Test [Enabled] Use the Quick Power On Self Test option to speed up the POST after the computer is turned on. If enabled, BIOS shortens or skips some POST check items. Disabled Enabled Normal POST occurs after the computer is turned on. (Default) Quick POST occurs after the computer is turned on. LAN(CN17/UP) BootROM [Disabled] Use the LAN(CN17/UP) BootROM option to enable the system to be booted from a remote system.
MODEL NAME ROCKY-3786EV CPU Card HDD-1 HDD-2 HDD-3 ZIP100 USB-FDD USB-ZIP USB-CDROM USB-HDD LAN Disabled Boot Other Device [Enabled] Use the Boot Other Device option to determine whether the system uses a second or third boot device if the first boot device is not found. The system does not look for second and third boot Disabled devices if the first one is not found. Enabled (Default) The system looks for second and third boot devices if the first one is not found.
ROCKY-3786EV CPU Card BIOS does not search for the type of FDD drive by track Disabled number. Note that there is no warning message if the drive installed is 360K. Enabled (Default) BIOS searches for a FDD to determine if it has 40 or 80 tracks. Note that BIOS cannot tell the difference between 720K, 1.2M or 1.44M drives as they all have 80 tracks. Boot Up Numlock Status [On] Use the Boot Up Numlock Status option to specify the default state of the numeric keypad.
MODEL NAME ROCKY-3786EV CPU Card x Typematic Rate (Chars/sec) [6] The Typematic Rate option can only be configured if the Typematic Rate Setting is enabled. Use the Typematic Rate option to specify the rate keys are accelerated.
ROCKY-3786EV CPU Card NOTE: To disable security, select the password setting in the Main Menu. When asked to enter a password, don’t type anything, press ENTER and the security is disabled. Once the security is disabled, the system boots and Setup can be accessed. OS Select For DRAM > 64MB [Non-OS2] Use the OS Select For DRAM > 64MB option to specify the operating system. Non-OS2 (Default) Select this option when not using the OS/2 operating system. Specifies the operating system used as OS/2.
MODEL NAME ROCKY-3786EV CPU Card Enabled EPA logo appears during boot up. 5.4 Advanced Chipset Features Use the Advanced Chipset Features menu (BIOS Menu 4) to change chipset configuration options. BIOS Menu 4: Advanced Chipset Features SDRAM CAS Latency Time [3] The CAS Latency Time configuration option refers to the Column Address Strobe (CAS) delay time.
ROCKY-3786EV CPU Card 7/9 5/7 Auto (Default) SDRAM RAS-to-CAS Delay [Auto] The SDRAM RAS-to-CAS Delay sets the delay between the RAS and CAS signals. The appropriate delay for the memory module is reflected in its rated timings. The following configuration options are available: 3 2 Auto (Default) SDRAM RAS Precharge Time [Auto] Use SDRAM RAS Precharge Time option to set the number of cycles required for the RAS to accumulate its charge before the SDRAM refreshes.
MODEL NAME ROCKY-3786EV CPU Card Video BIOS not written to C0000h-C7FFFh. Disabled Enabled (Default) Video BIOS is written to F0000h-FFFFFh. Memory Hole At 15M – 16M [Disabled] Use the Memory Hole At 15M – 16M option to reserve memory space between 15MB and 16MB for ISA expansion cards that require a specified area of memory to work properly. If an older ISA expansion card is used, please refer to the documentation that came with the card to see if it is necessary to reserve the space.
ROCKY-3786EV CPU Card AGP Graphics Aperture Size Use the AGP Graphics Aperture Size option to select the size of the AGP aperture. The aperture is a portion of the PCI memory address range dedicated for graphics memory address space. Host cycles that hit the aperture range are forwarded to the AGP without any translation.
MODEL NAME ROCKY-3786EV CPU Card 5.5 Integrated Peripherals Use the Integrated Peripherals menu (BIOS Menu 5) to change the configuration options for the attached peripheral devices. BIOS Menu 5: Integrated Peripherals On-Chip PCI IDE [Enabled] Use the On-Chip PCI IDE options below to select if the system uses the following integrated IDE controller or not: On-Chip Primary PCI IDE On-Chip Secondary PCI IDE The onboard IDE controller is not used.
ROCKY-3786EV CPU Card IDE PIO [Auto] Use the IDE PIO options below to select the Programmed Input/Output (PIO) mode for the following HDDs: IDE Primary Master PIO IDE Primary Slave PIO IDE Secondary Master PIO IDE Secondary Slave PIO (Default) Auto The computer selects the correct mode. Mode 0 PIO mode 0 selected with a maximum transfer rate of 3.3MBps. Mode 1 PIO mode 1 selected with a maximum transfer rate of 5.2MBps. Mode 2 PIO mode 2 selected with a maximum transfer rate of 8.3MBps.
MODEL NAME ROCKY-3786EV CPU Card Integrated USB controller disabled. Disabled Enabled (Default) Integrated USB controller enabled. USB(CN6) Keyboard Support [Enabled] Use the USB Keyboard Support option to enable or disable the use of a USB keyboard. USB keyboard cannot be used. Disabled Enabled (Default) USB keyboard can be used. Init Display First [PCI Slot] Use the Init Display First option to select the primary display device.
ROCKY-3786EV CPU Card Onboard FDC Controller [Enabled] Use the Onboard FDC Controller option to enable or disable the onboard floppy controller. If the system is not connected to a floppy disk or uses an adapter for the FDD, this option can be disabled. The FDD controller is disabled. Disabled Enabled (Default) The FDD controller is enabled. Onboard Serial Port 1 [3F8/IRQ4] Use the Onboard Serial Port 1 option to select the I/O address and IRQ for the onboard serial port 1.
MODEL NAME ROCKY-3786EV CPU Card Normal (Default) RS-232C serial port IrDA Infrared port compliant with IrDA 1.0 specification ASKIR Amplitude shift keyed infrared port SCR Scratch pad register UR2 Duplex Mode [Half] Use the UR2 Duplex Mode option to specify the transmission mode for the IR port device. Simultaneous bi-directional transmission occurs. Full Half (Default) Transmission only occurs in one direction at a time.
ROCKY-3786EV CPU Card port (ECP) mode. The ECP mode supports bi-directional communication between the system and the parallel port device and the transmission rates between the two are much faster than the SPP mode. The parallel port is compatible with both ECP and EPP ECP+EPP devices. ECP Mode Use DMA [3] Use the ECP Mode Use DMA option to specify the DMA channel the parallel port must use in the ECP mode. The parallel port uses DMA Channel 1 in ECP mode.
MODEL NAME ROCKY-3786EV CPU Card BIOS Menu 6: Power Management Setup ACPI Function [Enabled] Use the ACPI Function to enable the ACPI (Advanced Configuration and Power Interface) function. ACPI function disabled. Disabled Enabled (Default) ACPI function enabled. ACPI Suspend Type [S1(POS)] Use the ACPI Suspend Type BIOS option to specify the sleep state the system enters when not being used. S1 (POS) (Default) System appears off.
ROCKY-3786EV CPU Card Power Management [Min Saving] Use the Power Management option to specify the power management selection methods. User must define when the system goes into a User Defined sleep state or a suspend state. Min. Saving (Default) The longest period of time that can be specified before the system enters either the Doze mode or the suspend state. The longest time for either of these is one hour. Max.
MODEL NAME ROCKY-3786EV CPU Card Video Off In Suspend [Yes] Use Video Off In Suspend option to specify the status of the system display when the system is in a sleep or suspend state. The system display is on when the system is in a No suspend state. (Default) Yes The system display is off when the system is in a suspend state. Suspend Type [Stop Grant] The Suspend Type option specifies the CPU status during power saving mode.
ROCKY-3786EV CPU Card Disabled (Default) 1 Min 2 Min 4 Min 8 Min 12 Min 20 Min 30 Min 40 Min 1 Hour HDD Power Down [Disabled] Use the HDD Power Down option to specify how long the computer must wait for no activity before the HDD powers down. If this option is disabled, the HDD does not power down. The following settings can be made.
MODEL NAME ROCKY-3786EV CPU Card Soft-Off by PWR-BTTN [Instant-Off] Use the Soft-Off by PWR-BTTN option to enabled the system to enter a very low-power-usage state when the power button is pressed. Instant-Off (Default) When the power button is pressed, the system is immediately shutdown. To shutdown the system the power button must be held Delay 4-sec down longer than four seconds otherwise the system enters a low power usage state.
ROCKY-3786EV CPU Card Reload Global Timer Events The Reload Global Timer Events option allows the user to specify the following events that activate the power management timer. Primary IDE 0 Primary IDE 1 Secondary IDE 0 Secondary IDE 1 FDD, COM, LPT Port PCI PIRQ[A-D]# Disabled (Default) An event occurring on each listed device does not restart the global timer for Standby mode. Enabled An event occurring on each listed device restarts the global timer for Standby mode. 5.
MODEL NAME ROCKY-3786EV CPU Card BIOS Menu 7: PnP/PCI Configurations PNP OS Installed [No] The PNP OS Installed option determines whether the Plug and Play devices connected to the system are configured by the operating system or the BIOS. No (Default) If the operating system does not meet the Plug and Play specifications, BIOS configures all the devices in the system. Yes Set this option if the system is running Plug and Play aware operating systems.
ROCKY-3786EV CPU Card Resources Controlled By [Auto (ESCD)] Use the Resources Controlled By option to either manually configure all the boot and plug and play devices, or allow BIOS to configure these devices automatically. If BIOS is allowed to configure the devices automatically IRQs, DMA and memory base address fields cannot be set manually. Auto(ESCD) (Default) BIOS automatically configures plug and play devices as well as boot devices.
MODEL NAME ROCKY-3786EV CPU Card DMA Resources [Press Enter] The DMA Resources menu can only be accessed if the Resources Controlled By option is set to Manual. The menu has six configurable options: DMA-0 assigned to DMA-1 assigned to DMA-3 assigned to DMA-5 assigned to DMA-6 assigned to DMA-7 assigned to The above options all have the following default options.
ROCKY-3786EV CPU Card PCI Latency Timer (CLK) [32] The PCI Latency Timer (CLK) option defines the minimum amount of time, in PCI clock cycle, that the bus master can retain the ownership of the bus. The values are from 0 to 255. The default value is 32. 5.8 PC Health Status The PC Health Status menu (BIOS Menu 8) has no user configurable options, but shows system operating parameters that are essential to the stable operation of the system.
ROCKY-3786EV CPU Card MODEL NAME +5.0 V +12 V -12 V -5.0 V 5VSB Voltage Battery System Temperature The following temperatures are monitored: System Temperature CPU Temperature Fan Speeds The following fan speeds are monitored: FAN2 Speed FAN3 Speed 5.9 Frequency/Voltage Control Use the Frequency/Voltage Control menu (BIOS Menu 9) to set the frequency options for the DIMM, PCI and CPU host.
ROCKY-3786EV CPU Card BIOS Menu 9: Frequency/Voltage Control Auto Detect DIMM/PCI Clk [Enabled] Use the Auto Detect DIMM/PCI Clk option to actively reduce EMI (Electromagnetic Interference) and reduce power consumption by turning off unoccupied or inactive expansion slots. AGP, PCI and memory slots are not monitored. Disabled Enabled (Default) AGP, PCI and memory slots are monitored and clock signals to all unoccupied and inactive slots are turned off.
MODEL NAME ROCKY-3786EV CPU Card Disabled (Default) EMI not reduced. EMI reduced. Enabled CPU Host/PCI Clock [Default] Use the CPU Host/PCI Clock option to select a timing combination for the CPU and the PCI bus. When set to Default, the BIOS uses the actual CPU and PCI bus clock values. Configuration options are below. Default (Default) 83/28 MHz 90/30 MHz 100/33 MHz 103/34 MHz 112/37 MHz 115/38 MHz 120/40 MHz 125/42 MHz CPU Clock Ratio [X 3] Use the CPU Clock Ratio option to select CPU clock ratio.
ROCKY-3786EV CPU Card Chapter 6 6 Software Drivers Page 120 Page 120
ROCKY-3786EV CPU Card MODEL NAME 6.1 Available Software Drivers NOTE: The content of the CD may vary throughout the life cycle of the product and is subject to change without prior notice. Visit the IEI website or contact technical support for the latest updates. The ROCKY-3786EV CPU card has the following software drivers: ATI Display Driver Intel® Chipset Driver Realtek Lan Driver (For GbE Lan) All drivers can be found on the CD that came with the CPU card.
ROCKY-3786EV CPU Card Step 3: Once initialized, the ATI Software Setup welcome screen appears (Figure 6-2). Figure 6-2: ATI Software Setup Welcome Step 4: Click NEXT and the license agreement appears (Figure 6-3).
ROCKY-3786EV CPU Card MODEL NAME Figure 6-3: License Agreement Step 5: Read the license agreement. To accept the terms and conditions stipulated in the agreement, click YES and the Select Components screen appears (Figure 6-4).
ROCKY-3786EV CPU Card Figure 6-4: Select Components Step 6: There are two options for express or custom software installations. Click EXPRESS to continue (Figure 6-4). Step 7: The Hardware Installation window may appear (Figure 6-5). Click CONTINUE ANYWAY to continue.
ROCKY-3786EV CPU Card MODEL NAME Figure 6-5: Hardware Installation Step 8: The driver files are copied onto the system (Figure 6-6). Figure 6-6: Copying Driver Files Step 9: After the files are copied, the Setup Complete screen appears (Figure 6-7).
ROCKY-3786EV CPU Card Figure 6-7: Setup Complete Step 10: Once the installation process is complete, the computer may be restarted immediately or later. For the settings to take effect, the computer must be restarted. Click FINISH to restart the computer.Step 0: 6.3 Intel® Chipset Driver Installation To install the chipset driver, please follow the steps below. Step 1: Insert the Utility CD that came with the CPU card into the system CD drive.
ROCKY-3786EV CPU Card MODEL NAME Figure 6-8: Chipset Software Installation Utility Extracting Files Step 2: The Chipset Software Installation Utility prepares the InstallShield Wizard (Figure 6-9). Figure 6-9: InstallShield Wizard Preparation Screen Step 3: The InstallShield Wizard Welcome screen appears (Figure 6-10).
ROCKY-3786EV CPU Card Figure 6-10: Chipset Software Installation Utility Welcome Screen Step 4: Click NEXT and the license agreement appears (Figure 6-11).
ROCKY-3786EV CPU Card MODEL NAME Step 5: Read the license agreement. To accept the terms and conditions stipulated in the agreement, click YES and the Readme file information appears (Figure 6-12). Figure 6-12: Chipset Software Installation Utility Readme File Information Step 6: Read the Readme file information. Click NEXT and the chipset driver is installed (Figure 6-13).
ROCKY-3786EV CPU Card Figure 6-14: Chipset Software Installation Utility Complete Step 8: The confirmation screen offers the option of restarting the computer now or later. For the settings to take effect, the computer must be restarted. Click FINISH to restart the computer.Step 0: 6.4 Realtek LAN Driver (for GbE LAN) Installation To install the Realtek LAN driver, please follow the steps below. Step 1: Insert the Utility CD that came with the CPU card into the system CD drive.
ROCKY-3786EV CPU Card MODEL NAME Figure 6-15: Realtek LAN Driver InstallShield Wizard Step 2: The InstallShield Wizard Welcome screen appears (Figure 6-16).
ROCKY-3786EV CPU Card Step 3: Click NEXT and the Ready to Install screen appears (Figure 6-17). Figure 6-17: Realtek LAN Driver Ready to Install Step 4: Click INSTALL and the Setup Status screen appears as the driver is installed (Figure 6-18).
ROCKY-3786EV CPU Card MODEL NAME Step 5: After the driver installation process is complete, a confirmation screen appears (Figure 6-19). Figure 6-19: Realtek LAN Driver Installation Complete Step 6: Click FINISH to exit the InstallShield wizard.
ROCKY-3786EV CPU Card Appendix A A BIOS Configuration Options Page 134 Page 134
ROCKY-3786EV CPU Card MODEL NAME A.1 BIOS Configuration Options Below is a list of BIOS configuration options described in Chapter 5. Load Fail-Safe Defaults .................................................................................84 Load Optimized Defaults ...............................................................................84 Set Supervisor Password..............................................................................84 Set User Password.........................................
ROCKY-3786EV CPU Card Quick Power On Self Test [Enabled]............................................................92 LAN(CN17/UP) BootROM [Disabled] ............................................................92 Boot Device ....................................................................................................92 Boot Other Device [Enabled] ........................................................................93 Swap Floppy Drive [Disabled]....................................................
ROCKY-3786EV CPU Card MODEL NAME IDE HDD Block Mode [Enabled]................................................................. 103 Onboard FDC Controller [Enabled] ........................................................... 104 Onboard Serial Port 1 [3F8/IRQ4] .............................................................. 104 Onboard Serial Port 2 [2F8/IRQ3] .............................................................. 104 UART Mode Select [Normal] ........................................................
ROCKY-3786EV CPU Card Fan Speeds ................................................................................................. 117 Auto Detect DIMM/PCI Clk [Enabled] ........................................................ 118 Spread Spectrum [Disabled] ...................................................................... 118 CPU Host/PCI Clock [Default] .................................................................... 119 CPU Clock Ratio [X 3] .......................................................
ROCKY-3786EV CPU Card MODEL NAME Appendix B B Watchdog Timer Page 139 Page 139
ROCKY-3786EV CPU Card NOTE: The following discussion applies to DOS environment. It is recommended to contact IEI support or visit our website for specific drivers for more sophisticated operating systems, e.g., Windows and Linux. The Watchdog Timer is provided to ensure that standalone systems can always recover from catastrophic conditions that cause the CPU to crash. This condition may have occurred by external EMI or a software bug.
MODEL NAME ROCKY-3786EV CPU Card NOTE: When exiting a program it is necessary to disable the Watchdog Timer, otherwise the system will reset.
ROCKY-3786EV CPU Card Appendix C C External AC’97 Audio CODEC Page 142 Page 142
ROCKY-3786EV CPU Card MODEL NAME C.1 Introduction The CPU card comes with an onboard Realtek ALC655 CODEC. Realtek ALC655 is a 16-bit, full duplex AC’97 Rev. 2.3 compatible audio CODEC with a sampling rate of 48KHz. C.1.1 Accessing the AC’97 CODEC The CODEC is accessed through the phone jack on the rear panel of CPU card. The phone jack include: 1. A LINE input 2. A LINE output 3. A MIC input line 4. A Speaker output C.1.2 Driver Installation The driver installation has been described in Chapter 6.
ROCKY-3786EV CPU Card Figure C-1: Sound Effect Manager con C.2 Sound Effect Configuration C.2.1 Accessing the Sound Effects Manager To access the Sound Effects Manager, please do the following: Step 1: Install the audio CODEC driver. Step 2: Click either: The Sound Effect Manager icon in the Notification Area of the system task bar (see Figure C-2), or The Sound Effect Manager icon in the Control Panel (Figure C-3).
ROCKY-3786EV CPU Card MODEL NAME Figure C-3: Sound Effect Manager Icon [Control Panel] Step 3: The sound effect manager appears. (See Figure C-4) Step 0: Figure C-4: Sound Effects Manager (ALC655) NOTE: The Sound Effect Manager shown in Figure C-4 is for the RealTek ALC655 audio CODEC. Different CODECs may have different sound manager appearances. The following section describes the different configuration options in the Sound Effect Manager. C.2.
ROCKY-3786EV CPU Card NOTE: The Karaoke Mode is configured in the Sound Effect menu. To access Karaoke configuration settings, click on the Sound Effect menu tab. Sound Effect Karaoke Mode Equalizer Speaker Configuration Speaker Test S/PDIF-In S/PDIF-Out Connector Sensing HRTF Demo Microphone Effect General NOTE: Not all RealTek Sound Effect Managers have all the above listed options. The Sound Effect Manager loaded onto the system may only have some of the options listed above.
ROCKY-3786EV CPU Card MODEL NAME Karaoke Mode:- The Karaoke Mode is accessed in the Sound Effect window. The Voice Cancellation disables the vocal part of the music being played. The Key adjustment up or down arrow icons enables users to define a key that fits a certain vocal range. Equalizer Selection:- Preset equalizer settings enable easy audio range settings. Ten frequency bands can be configured. Speaker Configuration:- Multi-channel speaker settings are configured in this menu.
