Manual

ManualsBrandsIEI Integration ManualsComputer AccessoriesTANK-6000-C226

TANK-6000-C226 Embedded System

Page i

User Manual

MODEL:

TANK-6000-C226

Embedded s ystem supports 22nm LGA1155 Intel® Xeon® E3 / Core™

i3 CPU, HDMI, VGA, GbE, Two USB 2.0, Four USB 3.0,

Tw o COM and RoHS Compliant

Rev. 1.00 – 14 March 2014

Summary of content (138 pages)

PAGE 1
TANK-6000-C226 Em b e d d e d S ys te m , MODEL: TANK-6000-C226 Em b e d d e d s ys te m s u p p o rts 22n m LGA1155 In te l® Xe o n ® E3 / Co re ™ i3 CP U, HDMI, VGA, Gb E, Two US B 2.0, Fo u r US B 3.0, Two COM a n d Ro HS Co m p lia n t Us e r Ma n u a l Page i Re v. 1.
PAGE 2
TANK-6000-C226 Em b e d d e d S ys te m Re vis io n Date Version Changes 14 March 2014 1.
PAGE 3
TANK-6000-C226 Em b e d d e d S ys te m Co p yrig h t COP YRIGHT NOTICE The information in this document is subject to change without prior notice in order to improve reliability, design and function and does not represent a commitment on the part of the manufacturer. In no event will the manufacturer be liable for direct, indirect, special, incidental, or consequential damages arising out of the use or inability to use the product or documentation, even if advised of the possibility of such damages.
PAGE 4
TANK-6000-C226 Em b e d d e d S ys te m Ta b le o f Co n te n ts 1 INTRODUCTION.......................................................................................................... 1 1.1 OVERVIEW.................................................................................................................. 2 1.2 MODEL VARIATIONS ................................................................................................... 2 1.3 FEATURES ..........................................................
PAGE 5
TANK-6000-C226 Em b e d d e d S ys te m 3.8.5 USB Device Connection ................................................................................... 25 3.8.6 VGA Monitor Connection ................................................................................ 26 4 SYSTEM MOTHERBOARD ..................................................................................... 28 4.1 MOTHERBOARD LAYOUT.......................................................................................... 29 4.
PAGE 6
TANK-6000-C226 Em b e d d e d S ys te m 5.1.4 Unable to Reboot after Configuration Changes .............................................. 41 5.1.5 BIOS Menu Bar ................................................................................................ 41 5.2 MAIN ........................................................................................................................ 42 5.3 ADVANCED .........................................................................................................
PAGE 7
TANK-6000-C226 Em b e d d e d S ys te m A.2.2 Cleaning Tools ................................................................................................. 80 B BIOS MENU OPTIONS ............................................................................................. 81 C ONE KEY RECOVERY ............................................................................................. 84 C.1 ONE KEY RECOVERY INTRODUCTION ...................................................................... 85 C.1.
PAGE 8
TANK-6000-C226 Em b e d d e d S ys te m Lis t o f Fig u re s Figure 1-1: TANK-6000-C226 .........................................................................................................2 Figure 1-2: TANK-6000-C226 Front Panel ....................................................................................5 Figure 1-3: TANK-6000-C226 Rear Panel .....................................................................................6 Figure 1-4: Physical Dimensions (mm) .............................
PAGE 9
TANK-6000-C226 Em b e d d e d S ys te m Figure C-8: Building the Recovery Partition ..............................................................................95 Figure C-9: Press Any Key to Continue .....................................................................................95 Figure C-10: Press F3 to Boot into Recovery Mode..................................................................96 Figure C-11: Recovery Tool Menu ........................................................................
PAGE 10
TANK-6000-C226 Em b e d d e d S ys te m Lis t o f Ta b le s Table 1-1: Model Variations ...........................................................................................................2 Table 1-2: Technical Specifications ..............................................................................................4 Table 2-1: Package List Contents ...............................................................................................11 Table 4-1: Peripheral Interface Connectors ........
PAGE 11
TANK-6000-C226 Em b e d d e d S ys te m Ch a p te r 1 1 In tro d u c tio n Page 1
PAGE 12
TANK-6000-C226 Em b e d d e d S ys te m 1.1 Ove rvie w Figure 1-1: TANK-6000-C226 The TANK-6000-C226 embedded system is with one VGA port and one HDMI port for dual display. It accepts an Intel® Xeon® E3 / Core™ i3 CPU and supports four 240-pin DDR3 U-DIMM modules up to 64 GB. The TANK-6000-C226 supports one 2.5” SATA HDD with up to 3 Gb/s data transfer rate and two 2.5” SATA HDDs with up to 6 Gb/s data transfer rate. Two serial ports, two external USB 2.0 ports and four external USB 3.
PAGE 13
TANK-6000-C226 Em b e d d e d S ys te m 1.3 Fe a tu re s The TANK-6000-C226 features are listed below:  LGA1155 socket supports Intel® Xeon® E3 / Core™ i3 CPU (up to 95W CPU )  4 x 240-pin DDR3 U-DIMM (system max: 64GB)  Extended temperature design supports -20°C to 55°C  Easy to install Hard Disk Drive (HDD)  USB 3.0 for high super speed data transfer  Programmable OLED display  RoHS compliant 1.
PAGE 14
TANK-6000-C226 Em b e d d e d S ys te m I/O in te rfa c e s 4 x USB 3.0 US B 2 x USB 2.0 Eth e rn e t 1 x RJ-45 for Intel® i217 PHY with AMT 8.
PAGE 15
TANK-6000-C226 Em b e d d e d S ys te m  2 x HDD/SSD bay  1 x OLED display  1 x Power button  2 x USB 3.0 connectors Figure 1-2: TANK-6000-C226 Front Panel 1.
PAGE 16
TANK-6000-C226 Em b e d d e d S ys te m Figure 1-3: TANK-6000-C226 Rear Panel Page 6
PAGE 17
TANK-6000-C226 Em b e d d e d S ys te m 1.
PAGE 18
TANK-6000-C226 Em b e d d e d S ys te m Ch a p te r 2 2 Un p a c kin g Page 8
PAGE 19
TANK-6000-C226 Em b e d d e d S ys te m 2.1 An ti-s ta tic P re c a u tio n s WARNING: Failure to take ESD precautions during installation may result in permanent damage to the TANK-6000-C226 and severe injury to the user. Electrostatic discharge (ESD) can cause serious damage to electronic components, including the TANK-6000-C226. Dry climates are especially susceptible to ESD.
PAGE 20
TANK-6000-C226 Em b e d d e d S ys te m 2.3 Un pa c kin g Ch e c klis t NOTE: If some of the components listed in the checklist below are missing, please do not proceed with the installation. Contact the IEI reseller or vendor you purchased the TANK-6000-C226 from or contact an IEI sales representative directly. To contact an IEI sales representative, please send an email to sales@iei.com.tw.
PAGE 21
TANK-6000-C226 Em b e d d e d S ys te m Qu a n tity Ite m a n d P a rt Nu m b e r Im a g e Utility CD 1 1 One Key Recovery CD Table 2-1: Package List Contents P a g e 11
PAGE 22
TANK-6000-C226 Em b e d d e d S ys te m Ch a p te r 3 3 In s ta lla tio n P a g e 12
PAGE 23
TANK-6000-C226 Em b e d d e d S ys te m 3.1 In s ta lla tio n P re c a u tio n s During installation, be aware of the precautions below:  Read the user manual: The user manual provides a complete description of the TANK-6000-C226, installation instructions and configuration options.  DANGER! Disconnect Power: Power to the TANK-6000-C226 must be disconnected during the installation process, or before any attempt is made to access the rear panel.
PAGE 24
TANK-6000-C226 Em b e d d e d S ys te m 3.3 Ha rd Dis k Drive (HDD) In s ta lla tio n 3.3.1 S e ria l ATA 2.0 Drive In s ta lla tio n To install the hard disk drive to the SATA 2.0 driver bay, please follow the steps below: S te p 1: Remove two retention screws from the HDD cover, as shown in Figure 3-1. 35H Figure 3-1: HDD Cover Retention Screws S te p 2: Remove the HDD cover from the device. S te p 3: Loosen two HDD bracket retention screws (Figure 3-2).
PAGE 25
TANK-6000-C226 Em b e d d e d S ys te m Figure 3-2: HDD Bracket Retention Screws S te p 4: Lift the HDD bracket out of the TANK-6000-C226 and slide the HDD to the HDD bracket (Figure 3-3). 36H Figure 3-3: Inserting the HDD S te p 5: Install the HDD bracket in the same position it was before and tighten the HDD bracket retention screws. S te p 6: Reinstall the HDD cover.
PAGE 26
TANK-6000-C226 Em b e d d e d S ys te m 3.3.2 S e ria l ATA 3.0 Drive In s ta lla tio n To install the hard disk drive to the SATA 3.0 driver bay, please follow the steps below: S te p 1: Unlock the HDD drive bay using the key. The keys can be found in the packing list. Figure 3-4: HDD Drive Bay S te p 2: Loosen two HDD bracket retention screws and lift the HDD bracket out of the TANK-6000-C226.
PAGE 27
TANK-6000-C226 Em b e d d e d S ys te m Figure 3-6: Installing the HDD S te p 4: Install the HDD bracket in the same position it was before and tighten the HDD bracket retention screws. S te p 5: Lock the HDD drive bay using the key 3.4 P CIe Expa n s io n Ca rd In s ta lla tio n (Op tio n a l) To install a PCIe expansion card, please do the following. S te p 1: Loosen the two thumbscrews on the rear panel and remove the top cover. Then remove the two retention screws and open the side cover.
PAGE 28
TANK-6000-C226 Em b e d d e d S ys te m S te p 2: Remove the expansion slot cover. The expansion slot cover is secured to the system with a single retention screw. Remove the screw. Figure 3-8: Expansion Slot Retention Screw S te p 3: Insert the expansion card. Align the PCIe expansion card edge connector with the PCIe expansion slot on the PCIe riser card. Gently insert the PCIe card into the PCIe expansion slot. S te p 4: Secure the expansion card.
PAGE 29
TANK-6000-C226 Em b e d d e d S ys te m 3.5 AT/ATX Mo d e S e le c tio n AT or ATX power mode can be used on the TANK-6000-C226. The selection is made through an AT/ATX switch located on the rear panel. To select AT mode or ATX mode, follow the steps below. Locate the AT/ATX switch on the rear panel (Figure 3-10). S te p 1: Figure 3-10: AT/ATX Switch Location Adjust the AT/ATX switch. S te p 0: S te p 2: 3.5.
PAGE 30
TANK-6000-C226 Em b e d d e d S ys te m in standby mode. Remote power control is perfect for advertising applications since the broadcasting time for each panel PC can be set individually and controlled remotely. Other possible application includes:  Security surveillance  Point-of-Sale (POS)  Advertising terminal 3.6 Re s e t th e S ys te m The reset button enables user to reboot the system when the system is turned on. To reboot the system, follow the steps below.
PAGE 31
TANK-6000-C226 Em b e d d e d S ys te m Secure the brackets to the system by inserting two retention screws into each S te p 3: bracket as illustrated in Figure 3-12. 340H Figure 3-12: Mounting Bracket Retention Screws S te p 4: Drill holes in the intended installation surface. S te p 5: Align the mounting holes in the sides of the mounting brackets with the predrilled holes in the mounting surface. Insert four retention screws, two in each bracket, to secure the system to the S te p 6: wall.
PAGE 32
TANK-6000-C226 Em b e d d e d S ys te m To install these devices, connect the corresponding cable connector from the actual device to the corresponding TANK-6000-C226 external peripheral interface connector making sure the pins are properly aligned. 3.8.1 Au d io Co n n e c tio n The audio jacks on the external audio connector enable the TANK-6000-C226 to be connected to a stereo sound setup. To install the audio devices, follow the steps below. Identify the audio plugs.
PAGE 33
TANK-6000-C226 Em b e d d e d S ys te m 3.8.2 HDMI De vic e Co n n e c tio n The HDMI connector transmits a digital signal to compatible HDMI display devices such as a TV or computer screen. To connect the HDMI cable to the TANK-6000-C226, follow the steps below. S te p 1: Locate the HDMI connector. The location is shown in Chapter 1. S te p 2: Align the connector. Align the HDMI connector with the HDMI port. Make sure the orientation of the connector is correct.
PAGE 34
TANK-6000-C226 Em b e d d e d S ys te m S te p 1: Locate the RJ-45 connectors. The location of the LAN connector is shown in Chapter 1. S te p 2: Align the connectors. Align the RJ-45 connector on the LAN cable with one of the RJ-45 connectors on the TANK-6000-C226. See Figure 3-15. 360H Figure 3-15: LAN Connection S te p 3: Insert the LAN cable RJ-45 connector. Once aligned, gently insert the LAN cable RJ-45 connector into the RJ-45 connector. S te p 0: 3.8.
PAGE 35
TANK-6000-C226 Em b e d d e d S ys te m Figure 3-16: DB-9 Serial Port Connector S te p 3: Secure the connector. Secure the serial device connector to the external interface by tightening the two retention screws on either side of the connector. Step 0: 3.8.5 US B De vic e Co n n e c tio n NOTE: User must install the USB 3.0 driver before connecting a USB device to the system or else the system may not recognize the connected device. There are four USB 3.0 connectors and two USB 2.
PAGE 36
TANK-6000-C226 Em b e d d e d S ys te m S te p 2: Align the connectors. Align the USB device connector with one of the connectors on the external peripheral interface. See Figure 3-18. Figure 3-17: USB Device Connection S te p 3: Insert the device connector. Once aligned, gently insert the USB device connector into the onboard connector. 3.8.6 VGA Mo n ito r Co n n e c tio n The TANK-6000-C226 has one female DB-15 connectors on the external peripheral interface panel.
PAGE 37
TANK-6000-C226 Em b e d d e d S ys te m S te p 3: Insert the VGA connector. Once the connectors are properly aligned with the insert the male connector from the VGA screen into the female connector on the TANK-6000-C226. See Figure 3-19. Figure 3-18: VGA Connector S te p 4: Secure the connector. Secure the DB-15 VGA connector from the VGA monitor to the external interface by tightening the two retention screws on either side of the connector.
PAGE 38
TANK-6000-C226 Em b e d d e d S ys te m Ch a p te r 4 4 S ys te m Mo th e rb o a rd P a g e 28
PAGE 39
TANK-6000-C226 Em b e d d e d S ys te m 4.1 Mo th e rb o a rd La yo u t The TANK-6000-C226 embedded system motherboard comes with a number of peripheral interface connectors and configuration jumpers. The connector locations are shown in Figure 6-1. The Pin 1 locations of the on-board connectors are also indicated in the diagrams. The connector pinouts for these connectors are listed in the following sections.
PAGE 40
TANK-6000-C226 Em b e d d e d S ys te m 4.2 In te rn a l P e rip h e ra l Co n n e c to rs Internal peripheral connectors are found on the motherboard and are only accessible when the motherboard is outside of the chassis. The table below shows a list of the peripheral interface connectors on the TANK-6000-C226 motherboard. Pinouts of these connectors can be found in the following sections.
PAGE 41
TANK-6000-C226 Em b e d d e d S ys te m 4.2.2 Ba tte ry Co n n e c to r (BAT1) PIN NO. DESCRIPTION 1 VBATT 2 GND Table 4-3: Battery Connector (BAT1) Pinouts 4.2.3 BMC De b u g Co n n e c to r (J 2_BMC) PIN NO. DESCRIPTION PIN NO. DESCRIPTION 1 V_3P3_A 2 BMC_TXD5 3 BMC_RXD5 4 GND Table 4-4: BMC Debug Connector (J2_BMC) Pinouts 4.2.4 EC De b u g P o rt Co n n e c to r (CN2) PIN NO. DESCRIPTION PIN NO.
PAGE 42
TANK-6000-C226 Em b e d d e d S ys te m 4.2.5 Fa n Co n n e c to rs (CP U_FAN1, S YS _FAN2) PIN NO. DESCRIPTION 1 GND 2 +12V 3 FANIO 4 PWM Table 4-6: Fan Connectors (CPU_FAN1, SYS_FAN2) Pinouts 4.2.6 Fla s h BIOS ROM Co n n e c to r (J S P I1) PIN NO. DESCRIPTION 1 +V3.3M_SPI_CON 2 SPI_CS#0_CN 3 SPI_SO_SW 3 SPI_CLK_SW 5 SPI_SI_SW 6 GND Table 4-7: Flash BIOS ROM Connector (JSPI1) Pinouts 4.2.7 Fla s h EC ROM Co n ne c to r (J S P I2) PIN NO. DESCRIPTION 1 +3.
PAGE 43
TANK-6000-C226 Em b e d d e d S ys te m 4.2.8 Fla s h BMC ROM Co n n e c to r (S P I1) PIN NO. DESCRIPTION 1 SPI_VCC 2 FLA_CS0_R 3 FLA_D2_R 3 FLA_D0_R 5 FLA_D1_R 6 GND Table 4-9: Flash BMC ROM Connector (SPI1) Pinouts 4.2.9 OLED Co n n e c to r (OLED1) PIN NO. DESCRIPTION 1 12VWidth 2 V_3P3_A 3 GND 3 OLED_RX 5 OLED_TX 6 GND Table 4-10: OLED Connector (OLED1) Pinouts 4.2.10 P owe r o n Co n n e c to r (CN3) PIN NO.
PAGE 44
TANK-6000-C226 Em b e d d e d S ys te m 4.2.11 S e ria l ATA 3.0 c o n n e c to rs (S ATA1) PIN NO. DESCRIPTION PIN NO. DESCRIPTION S1 GND P5 GND S2 SATA_TX2+_C P6 GND S3 SATA_TX2-_C P7 +5V S4 GND P8 +5V S5 SATA_RX2-_C P9 +5V S6 SATA_RX2+_C P10 GND S7 GND P11 GND P1 +3.3V P12 GND P2 +3.3V P13 +12V P3 +3.3V P14 +12V P4 GND P15 +12V Table 4-12: Serial ATA 3.0 connectors (SATA1) Pinouts 4.
PAGE 45
TANK-6000-C226 Em b e d d e d S ys te m Co n n e c to r Typ e La b e l USB 2.0 connector Dual USB 2.0 port USB_CON3 VGA connector 15-pin female VGA1 Table 4-13: Rear Panel Connectors 4.3.1 Au d io In p u t & Ou tp u t Co n n e c to rs (MIC1, AUDIO1) PIN NO. DESCRIPTION MIC1 (Line_Out) Connect this port to headphone or speaker AUDIO1 (Microphone) Connect this port to microphone Table 4-14: Audio Input & Output Connectors (MIC1, AUDIO1) Pinouts 4.3.
PAGE 46
TANK-6000-C226 Em b e d d e d S ys te m 4.3.4 Eth e rn e t Co n n e c to rs (LAN3, LAN4) PIN NO. DESCRIPTION PIN NO. DESCRIPTION C1 LAN1_MDI0P C5 LAN1_MDI2P C2 LAN1_MDI0N C6 LAN1_MDI2N C3 LAN1_MDI1P C7 LAN1_MDI3P C4 LAN1_MDI1N C8 LAN1_MDI3N Table 4-17: Ethernet Connector (LAN3, LAN4) Pinouts 4.3.5 Exte rn a l Fib e r Co n n e c to rs (S FP LAN1, S FP LAN 2) PIN NO. DESCRIPTION PIN NO.
PAGE 47
TANK-6000-C226 Em b e d d e d S ys te m 8 GND 20 HDMI_GND 9 HDMI_DATA0# 21 HDMI_GND 10 HDMI_CLK 22 HDMI_GND 11 GND 23 HDMI_GND 12 HDMI_CLK# Table 4-19: HDMI Connector (HDMI1) Pinouts 4.3.7 RS -232 S e ria l P o rt (COM1_2) PIN NO. DESCRIPTION PIN NO.
PAGE 48
TANK-6000-C226 Em b e d d e d S ys te m 1 VCC 10 VCC 2 USB_DATA- 11 USB_DATA- 3 USB_DATA+ 12 USB_ DATA+ 4 GND 13 GND 5 USB3_RX- 14 USB3_RX- 6 USB3_RX+ 15 USB3_ RX+ 7 GND 16 GND 8 USB3_TX- 17 USB3_TX- 9 USB3_TX+ 18 USB3_TX+ Table 4-22: USB 3.0 Connector (USB_CON4) Pinouts 4.3.10 US B 2.0 Co n n e c to rs (US B_CON3) PIN NO. DESCRIPTION PIN NO. DESCRIPTION 1 VCC 5 VCC 2 USB_DATA- 6 USB_DATA- 3 USB_DATA+ 7 USB_DATA+ 4 GND 8 GND Table 4-23: USB 3.
PAGE 49
TANK-6000-C226 Em b e d d e d S ys te m Ch a p te r 5 5 BIOS P a g e 39
PAGE 50
TANK-6000-C226 Em b e d d e d S ys te m 5.1 In tro d u c tio n The BIOS is programmed onto the BIOS chip. The BIOS setup program allows changes to certain system settings. This chapter outlines the options that can be changed. NOTE: Some of the BIOS options may vary throughout the life cycle of the product and are subject to change without prior notice. 5.1.1 Sta rtin g S e tu p The UEFI BIOS is activated when the computer is turned on. The setup program can be activated in one of two ways. 1.
PAGE 51
TANK-6000-C226 Em b e d d e d S ys te m Ke y Fu n c tio n - Decrease the numeric value or make changes Esc key Main Menu – Quit and not save changes into CMOS Status Page Setup Menu and Option Page Setup Menu -Exit current page and return to Main Menu F1 key General help, only for Status Page Setup Menu and Option Page Setup Menu F2 key Load previous values F3 key Load optimized defaults F4 key Save changes and Exit BIOS Table 5-1: BIOS Navigation Keys 5.1.
PAGE 52
TANK-6000-C226 Em b e d d e d S ys te m The following sections completely describe the configuration options found in the menu items at the top of the BIOS screen and listed above. 5.2 Ma in The Main BIOS menu (BIOS Menu 1) appears when the BIOS Setup program is entered. The Main menu gives an overview of the basic system information.
PAGE 53
TANK-6000-C226 Em b e d d e d S ys te m Aptio Setup Utility – Copyright (C) 2012 American Megatrends, Inc. Main Advanced Chipset Boot Security Save & Exit BIOS Information BIOS Vendor Core Version Compliency Project Version Build Date American Megatrends 4.6.5.4 UEFI 2.3.1;PI 1.2 SE71AR07.ROM 12/20/2013 20:05:21 iWDD Vendor iWDD Version iEi SE71ER16.
PAGE 54
TANK-6000-C226 Em b e d d e d S ys te m  BIOS Information  Processor Information  Memory Information  PCH Information  SPI Clock Frequency The Main menu has two user configurable fields:  S ys te m Da te [xx/xx/xx] Use the System Date option to set the system date. Manually enter the day, month and year.  S ys te m Tim e [xx:xx:xx] Use the System Time option to set the system time. Manually enter the hours, minutes and seconds. 5.
PAGE 55
TANK-6000-C226 Em b e d d e d S ys te m Aptio Setup Utility – Copyright (C) 2012 American Megatrends, Inc.
PAGE 56
TANK-6000-C226 Em b e d d e d S ys te m  ACP I S le e p Sta te [S 1 o n ly (CP U Sto p Clo c k)] Use the ACPI Sleep State option to specify the sleep state the system enters when it is not being used.  S1 only (CPU Stop DEFAULT The system enters S1 (POS) sleep state. The system appears off. The CPU is stopped; RAM is Clock) refreshed; the system is running in a low power mode.  S3 only (Suspend The caches are flushed and the CPU is powered to RAM) off. Power to the RAM is maintained.
PAGE 57
TANK-6000-C226 Em b e d d e d S ys te m  Wa ke S ys te m with Fixe d Tim e [Dis a b le d ] Use the Wake System with Fixed Time option to specify the time the system should be roused from a suspended state.
PAGE 58
TANK-6000-C226 Em b e d d e d S ys te m Aptio Setup Utility – Copyright (C) 2012 American Megatrends, Inc. Advanced CPU Information Intel® COR(TM) i7-4770S CPU @ 3.
PAGE 59
TANK-6000-C226 Em b e d d e d S ys te m  Intel SMX Technology: Indicates if Intel SMX Technology is supported by the CPU.  EIST Technology: Indicates if Enhanced Intel SpeedStep® Techonology is supported by the CPU.   L1 Data Cache: Lists the amount of data storage space on the L1 cache.  L1 Code Cache: Lists the amount of code storage space on the L1 cache.  L2 Cache: Lists the amount of storage space on the L2 cache.  L3 Cache: Lists the amount of storage space on the L3 cache.
PAGE 60
TANK-6000-C226 Em b e d d e d S ys te m  EIS T [En a b le d ] Use the EIST option to enable or disable Enhanced Intel SpeedStep® Techonology (EIST).  Disables Enhanced Intel SpeedStep® Disabled Techonology.  Enabled DEFAULT Enables Enhanced Intel SpeedStep® Techonology. 5.3.4 S ATA Co n fig u ra tio n Use the SATA Configuration menu (BIOS Menu 6) to change and/or set the configuration of the SATA devices installed in the system. Aptio Setup Utility – Copyright (C) 2012 American Megatrends, Inc.
PAGE 61
TANK-6000-C226 Em b e d d e d S ys te m   Disables the on-board SATA controller. Disabled S ATA Mo d e S e le c tio n [IDE Mo d e ] Use the SATA Mode Selection option to configure SATA devices as normal IDE devices.  IDE  AHCI Configures SATA devices as AHCI device.  RAID Configures SATA devices as RAID device. DEFAULT Configures SATA devices as normal IDE device. 5.3.
PAGE 62
TANK-6000-C226 Em b e d d e d S ys te m  Intel® Rapid Start Technology is enabled Enabled 5.3.6 AMT Co n fig u ra tio n The AMT Configuration submenu (BIOS Menu 8) allows Intel® Active Management Technology (AMT) options to be configured. Aptio Setup Utility – Copyright (C) 2012 American Megatrends, Inc. Advanced Intel AMT Un-Configure ME [Enabled] [Disabled] Enable/Disable Intel(R) Active Management Technology BIOS Extension. Note : iAMT H/W is always enabled.
PAGE 63
TANK-6000-C226 Em b e d d e d S ys te m  Disabled  Enabled Disable ME unconfigure DEFAULT Enable ME unconfigure 5.3.7 US B Co n fig u ra tio n Use the USB Configuration menu (BIOS Menu 9) to read USB configuration information and configure the USB settings. Aptio Setup Utility – Copyright (C) 2012 American Megatrends, Inc. Advanced USB Configuration USB Devices: 1 Keyboard, 2 Hubs Legacy USB Support [Enabled] Enables Legacy USB support.
PAGE 64
TANK-6000-C226 Em b e d d e d S ys te m keyboard can control the system even when there is no USB driver loaded onto the system.  Enabled  Disabled Legacy USB support disabled  Auto Legacy USB support disabled if no USB devices are DEFAULT Legacy USB support enabled connected 5.3.8 F81866 S u pe r IO Co nfig u ra tio n Use the F81866 Super IO Configuration menu (BIOS Menu 10) to set or change the configurations for the FDD controllers, parallel ports and serial ports.
PAGE 65
TANK-6000-C226 Em b e d d e d S ys te m 5.3.8.1 S e ria l P o rt n Co n fig u ra tio n Use the Serial Port n Configuration menu (BIOS Menu 11) to configure the serial port n. Aptio Setup Utility – Copyright (C) 2012 American Megatrends, Inc. Advanced Serial Port n Configuration Serial Port Device Settings Enable or Disable Serial Port (COM) [Enabled] IO=3F8h;IRQ=4 --------------------: Select Screen ↑ ↓: Select Item Enter Select = - Change Opt.
PAGE 66
TANK-6000-C226 Em b e d d e d S ys te m    IO=3F8h; Serial Port I/O port address is 3F8h and the interrupt IRQ=3, 4 address is IRQ3,4 IO=2C0h; Serial Port I/O port address is 2C0h and the interrupt IRQ=3, 4 address is IRQ3, 4 IO=2C8h; Serial Port I/O port address is 2C8h and the interrupt IRQ=3, 4 address is IRQ3, 4 5.3.8.1.2 S e ria l P o rt 2 Co n fig u ra tio n  S e ria l P o rt [En a b le d ] Use the Serial Port option to enable or disable the serial port.
PAGE 67
TANK-6000-C226 Em b e d d e d S ys te m 5.3.9 iWDD H/W Mo n ito r The iWDD H/W Monitor menu (BIOS Menu 12) contains the fan configuration submenus and displays operating temperature, fan speeds and system voltages. Aptio Setup Utility – Copyright (C) 2012 American Megatrends, Inc. Advanced PC Health Status Smart Fan Mode Select > Smart Fan Mode Configuration CPU Temperature SYS Temperature CPU_FAN1 Speed SYS_FAN1 Speed CPU_CORE +5V +12V DDR +5VSB +3.3V +3.3VSB :+49 C :+27 C :709 RPM :N/A :+1.743 V :+5.
PAGE 68
TANK-6000-C226 Em b e d d e d S ys te m o o +3.3V +3.3VSB 5.3.9.1 S m a rt Fa n Mo d e Co nfig u ra tio n Use the Smart Fan Mode Configuration submenu (BIOS Menu 13) to configure smart fan temperature and speed settings. Aptio Setup Utility – Copyright (C) 2012 American Megatrends, Inc.
PAGE 69
TANK-6000-C226 Em b e d d e d S ys te m  Fa n s ta rt P WM Use the + or – key to change the Fan start PWM value. Enter a decimal number between 1 and 128.  Fa n s lo p e P WM Use the + or – key to change the Fan slope PWM value. Enter a decimal number between 1 and 64. 5.3.10 S e ria l P o rt Co n s o le Re d ire c tio n The Serial Port Console Redirection menu (BIOS Menu 14) allows the console redirection options to be configured.
PAGE 70
TANK-6000-C226 Em b e d d e d S ys te m  Enabled the console redirection function Enabled The following options are available in the Console Redirection Settings submenu when the Console Redirection option is enabled.  Te rm in a l Typ e [ANS I] Use the Terminal Type option to specify the remote terminal type.
PAGE 71
TANK-6000-C226 Em b e d d e d S ys te m  None  Even DEFAULT No parity bit is sent with the data bits. The parity bit is 0 if the number of ones in the data bits is even.  The parity bit is 0 if the number of ones in the data Odd bits is odd.  The parity bit is always 1. This option does not Mark provide error detection.  The parity bit is always 0. This option does not Space provide error detection.
PAGE 72
TANK-6000-C226 Em b e d d e d S ys te m 5.3.11 iEi Fe a tu re Use the iEi Feature menu (BIOS Menu 15) to configure IEI One Key Recovery function. Aptio Setup Utility – Copyright (C) 2012 American Megatrends, Inc. Advanced iEi Feature Auto Recovery Function [Disabled] Auto Recovery Function Reboot and recover system automatically within 10 min, when OS crashes. Please install Auto Recovery API service before enabling this function.
PAGE 73
TANK-6000-C226 Em b e d d e d S ys te m 5.4 Ch ips e t Use the Chipset menu (BIOS Menu 16) to access the PCH-IO and System Agent (SA) Subsystem configuration menus. WARNING! Setting the wrong values for the Chipset BIOS selections in the Chipset BIOS menu may cause the system to malfunction. Aptio Setup Utility – Copyright (C) 2012 American Megatrends, Inc. Main Advanced Chipset Boot Security Save & Exit > PCH-IO Configuration > System Agent (SA) Configuration PCH Parameters.
PAGE 74
TANK-6000-C226 Em b e d d e d S ys te m 5.4.1 P CH-IO Co n fig u ra tio n Use the PCH-IO Configuration menu (BIOS Menu 17) to configure the PCH chipset. Aptio Setup Utility – Copyright (C) 2012 American Megatrends, Inc. Chipset Auto Power Button Status [Disabled (ATX)] Restore AC Power Loss [Last State] Select AC power state when power is re-applied after a power failure.
PAGE 75
TANK-6000-C226 Em b e d d e d S ys te m   Power Saving Function support enabled Enabled US B P o we r S W1 [+5V DUAL] Use the USB Power SW1 BIOS option to configure the USB power source for the corresponding USB connector.  +5V  +5V DUAL Set the USB power source to +5V DEFAULT Set the USB power source to +5V dual 5.4.1.1 P CH Aza lia Co n fig u ra tio n Use the PCH Azalia Configuration submenu (BIOS Menu 18) to configure the PCH Azalia codec.
PAGE 76
TANK-6000-C226 Em b e d d e d S ys te m  Enabled DEFAULT The onboard High Definition Audio controller is detected automatically and enabled 5.4.2 S ys te m Ag e n t (S A) Co n fig u ra tio n Use the System Agent (SA) Configuration menu (BIOS Menu 19) to configure the video device connected to the system. Aptio Setup Utility – Copyright (C) 2012 American Megatrends, Inc. Advanced VT-d [Enabled] Check to enable VT-d function on MCH.
PAGE 77
TANK-6000-C226 Em b e d d e d S ys te m 5.4.2.1 Gra p h ic s Co n fig u ra tio n Use the Graphics Configuration submenu (BIOS Menu 20) to configure the graphics settings. Aptio Setup Utility – Copyright (C) 2012 American Megatrends, Inc. Chipset Graphics Configuration Primary Display DVMT Pre-Allocated DVMT Total Gfx Mem > LCD Control [Auto] [256M] [MAX] Select which of IGFX/PEG/PCI Graphics device should be Primary Display Or select SG for Switchable Gfx.
PAGE 78
TANK-6000-C226 Em b e d d e d S ys te m  64M 64 MB of memory used by internal graphics device  128M 128 MB of memory used by internal graphics device  256M DEFAULT 256 MB of memory used by internal graphics device  512 MB of memory used by internal graphics 512M device  DVMT To ta l Gfx Me m [Max] Use the DVMT Total Gfx Mem option to specify the maximum amount of memory that can be allocated as graphics memory. Configuration options are listed below.  128M  256M  MAX Default 5.
PAGE 79
TANK-6000-C226 Em b e d d e d S ys te m Aptio Setup Utility – Copyright (C) 2012 American Megatrends, Inc. Chipset LCD Control Primary IGFX Boot Display [VBIOS Default] Select the Video Device which will be activated during POST. This has no effect if external graphics present. Secondary boot display selection will appear based on your selection. VGA modes will be supported only on primary display. ---------------------: Select Screen ↑ ↓: Select Item Enter: Select +/-: Change Opt.
PAGE 80
TANK-6000-C226 Em b e d d e d S ys te m 5.4.2.2 NB P CIe Co n fig u ra tio n Use the NB PCIe Configuration submenu (BIOS Menu 22) to configure the northbridge PCIe settings. Aptio Setup Utility – Copyright (C) 2012 American Megatrends, Inc. Chipset NB PCIe Configuration PEG0 PEG0-Gen X x0 Gen1 [Gen1] Enable PEG Detect Non-Compliance Device [Enabled] [Enabled] Configure PEG0 B0:D1:F0 Gen1-Gen3 (PCIEX16_1 Slot) --------------------: Select Screen ↑ ↓: Select Item Enter Select + - Change Opt.
PAGE 81
TANK-6000-C226 Em b e d d e d S ys te m  De te c t No n -Co m p lia n c e [En a b le d ] Use the Detect Non-Compliance option to detect non-compliance PCIe device in PEG.  Disabled  Enabled Do not detect non-compliance PCIe device in PEG DEFAULT Detect non-compliance PCIe device in PEG 5.4.2.3 Me m o ry Co n fig u ra tio n Use the Memory Configuration submenu (BIOS Menu 23) to configure the Memory settings. Aptio Setup Utility – Copyright (C) 2012 American Megatrends, Inc.
PAGE 82
TANK-6000-C226 Em b e d d e d S ys te m 5.5 Bo o t Use the Boot menu (BIOS Menu 24) to configure system boot options. Aptio Setup Utility – Copyright (C) 2012 American Megatrends, Inc.
PAGE 83
TANK-6000-C226 Em b e d d e d S ys te m  Qu ie t Bo o t [En a b le d ] Use the Quiet Boot BIOS option to select the screen display when the system boots.   Disabled  Enabled Normal POST messages displayed DEFAULT OEM Logo displayed instead of POST messages Op tio n ROM Me s s a g e s [Fo rc e BIOS ] Use the Option ROM Messages option to set the Option ROM display mode.  Force DEFAULT Sets display mode to force BIOS. BIOS  Sets display mode to current.
PAGE 84
TANK-6000-C226 Em b e d d e d S ys te m 5.6 S e c u rity Use the Security menu (BIOS Menu 25) to set system and user passwords. Aptio Setup Utility – Copyright (C) 2012 American Megatrends, Inc. Main Advanced Chipset Boot Security Save & Exit Password Description If ONLY the Administrator’s password is set, then this only limits access to Setup and is only asked for when entering Setup. If ONLY the User’s password is set, then this is a power on password and must be entered to boot or enter Setup.
PAGE 85
TANK-6000-C226 Em b e d d e d S ys te m Aptio Setup Utility – Copyright (C) 2012 American Megatrends, Inc. Main Advanced Chipset Boot Security Save & Exit Save Changes and Reset Discard Changes and Reset Exit the system after saving the changes. Restore Defaults Save as User Defaults Restore User Defaults --------------------: Select Screen ↑ ↓: Select Item Enter Select + - Change Opt. F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save & Exit ESC Exit Version 2.15.1236.
PAGE 86
TANK-6000-C226 Em b e d d e d S ys te m Appendix A A S a fe ty P re c a u tio n s P a g e 76
PAGE 87
TANK-6000-C226 Em b e d d e d S ys te m WARNING: The precautions outlined in this chapter should be strictly followed. Failure to follow these precautions may result in permanent damage to the TANK-6000-C226. A.1 S a fe ty P re c a u tio n s Please follow the safety precautions outlined in the sections that follow: A.1.1 Ge n e ra l S a fe ty P re c a u tio n s Please ensure the following safety precautions are adhered to at all times.
PAGE 88
TANK-6000-C226 Em b e d d e d S ys te m A.1.2 An ti-s ta tic P re c a u tio n s WARNING: Failure to take ESD precautions during the installation of the TANK-6000-C226 may result in permanent damage to the TANK-6000-C226 and severe injury to the user. Electrostatic discharge (ESD) can cause serious damage to electronic components, including the TANK-6000-C226. Dry climates are especially susceptible to ESD.
PAGE 89
TANK-6000-C226 Em b e d d e d S ys te m A.1.3 P ro d u c t Dis p o s a l CAUTION: Risk of explosion if battery is replaced by and incorrect type. Only certified engineers should replace the on-board battery. Dispose of used batteries according to instructions and local regulations.  Outside the European Union - If you wish to dispose of used electrical and electronic products outside the European Union, please contact your local authority so as to comply with the correct disposal method.
PAGE 90
TANK-6000-C226 Em b e d d e d S ys te m  The interior of the TANK-6000-C226X does not require cleaning. Keep fluids away from the TANK-6000-C226 interior.  Be cautious of all small removable components when vacuuming the TANK-6000-C226.  Turn the TANK-6000-C226 off before cleaning the TANK-6000-C226.  Never drop any objects or liquids through the openings of the TANK-6000-C226.  Be cautious of any possible allergic reactions to solvents or chemicals used when cleaning the TANK-6000-C226.
PAGE 91
TANK-6000-C226 Em b e d d e d S ys te m Appendix B B BIOS Me n u Op tio n s P a g e 81
PAGE 92
TANK-6000-C226 Em b e d d e d S ys te m  System Date [xx/xx/xx] ........................................................................................................44  System Time [xx:xx:xx] .......................................................................................................44  ACPI Sleep State [S1 only (CPU Stop Clock)] ...................................................................46  Wake System with Fixed Time [Disabled] ............................................
PAGE 93
TANK-6000-C226 Em b e d d e d S ys te m  Azalia [Enabled] ...................................................................................................................65  VT-d [Enabled] ......................................................................................................................66  Primary Display [Auto] ........................................................................................................67  DVMT Pre-Allocated [256M] ..............................
PAGE 94
TANK-6000-C226 Em b e d d e d S ys te m Ap p e n d ix C C On e Ke y Re c o ve ry P a g e 84
PAGE 95
TANK-6000-C226 Em b e d d e d S ys te m C.1 On e Ke y Re c o ve ry In tro d u c tio n The IEI one key recovery is an easy-to-use front end for the Norton Ghost system backup and recovery tool. This tool provides quick and easy shortcuts for creating a backup and reverting to that backup or reverting to the factory default settings.
PAGE 96
TANK-6000-C226 Em b e d d e d S ys te m After completing the five initial setup procedures as described above, users can access the recovery tool by pressing while booting up the system. The detailed information of each function is described in Section C.5. NOTE: The initial setup procedures for Linux system are described in Section C.3. C.1.1 S ys te m Re q u ire m e n t NOTE: The recovery CD can only be used with IEI products.
PAGE 97
TANK-6000-C226 Em b e d d e d S ys te m partitions. Please take the following table as a reference when calculating the size of the partition. OS OS Image after Ghost Compression Ratio Windows® 7 7 GB 5 GB 70% Windows® XPE 776 MB 560 MB 70% Windows® CE 6.0 36 MB 28 MB 77% NOTE: Specialized tools are required to change the partition size if the operating system is already installed. C.1.
PAGE 98
TANK-6000-C226 Em b e d d e d S ys te m o o o o o o o Ubuntu 8.10 (Intrepid) Ubuntu 7.10 (Gutsy) Ubuntu 6.10 (Edgy) Debian 5.0 (Lenny) Debian 4.0 (Etch) SuSe 11.2 SuSe 10.3 NOTE: Installing unsupported OS versions may cause the recovery tool to fail. C.2 S e tu p P ro c e d u re fo r Win d ows Prior to using the recovery tool to backup or restore, a few setup procedures are required. S te p 1: Hardware and BIOS setup (see Section C.2.1) S te p 2: Create partitions (see Section C.2.
PAGE 99
TANK-6000-C226 Em b e d d e d S ys te m C.2.1 Ha rdwa re a n d BIOS S e tu p S te p 1: Make sure the system is powered off and unplugged. S te p 2: Install a hard drive or SSD in the system. An unformatted and unpartitioned disk is recommended. S te p 3: Connect an optical disk drive to the system and insert the recovery CD. S te p 4: Turn on the system. S te p 5: Press the key as soon as the system is turned on to enter the BIOS.
PAGE 100
TANK-6000-C226 Em b e d d e d S ys te m Figure C-2: Launching the Recovery Tool S te p 3: The recovery tool setup menu is shown as below. Figure C-3: Recovery Tool Setup Menu S te p 4: P a g e 90 Press <6> then .
PAGE 101
TANK-6000-C226 Em b e d d e d S ys te m Figure C-4: Command Prompt S te p 5: The command prompt window appears. Type the following commands (marked in red) to create two partitions. One is for the OS installation; the other is for saving recovery files and images which will be an invisible partition.
PAGE 102
TANK-6000-C226 Em b e d d e d S ys te m Figure C-5: Partition Creation Commands P a g e 92
PAGE 103
TANK-6000-C226 Em b e d d e d S ys te m NOTE: Use the following commands to check if the partitions were created successfully. S te p 6: Press any key to exit the recovery tool and automatically reboot the system. Please continue to the following procedure: Build the Recovery Partition.Step0: C.2.3 In s ta ll Op e ra tin g S ys te m , Drive rs a n d Ap p lic a tio n s Install the operating system onto the unlabelled partition.
PAGE 104
TANK-6000-C226 Em b e d d e d S ys te m C.2.4 Bu ild in g th e Re c o ve ry P a rtitio n S te p 1: Put the recover CD in the optical drive. S te p 2: Start the system. S te p 3: Boot the system from the recovery CD. When prompted, press any key to boot from the recovery CD. It will take a while to launch the recovery tool. Please be patient! Figure C-6: Launching the Recovery Tool S te p 4: When the recovery tool setup menu appears, press <2> then .
PAGE 105
TANK-6000-C226 Em b e d d e d S ys te m S te p 5: The Symantec Ghost window appears and starts configuring the system to build a recovery partition. In this process the partition created for recovery files in Section C.2.2 is hidden and the recovery tool is saved in this partition. Figure C-8: Building the Recovery Partition S te p 6: After completing the system configuration, press any key in the following window to reboot the system.
PAGE 106
TANK-6000-C226 Em b e d d e d S ys te m C.2.5 Cre a te Fa c to ry De fa u lt Im a g e NOTE: Before creating the factory default image, please configure the system to a factory default environment, including driver and application installations. To create a factory default image, please follow the steps below. S te p 1: Turn on the system. When the following screen displays (Figure C-10), press the key to access the recovery tool.
PAGE 107
TANK-6000-C226 Em b e d d e d S ys te m Figure C-12: About Symantec Ghost Window S te p 4: Use mouse to navigate to the option shown below (Figure C-13). Figure C-13: Symantec Ghost Path S te p 5: Select the local source drive (Drive 1) as shown in Figure C-14. Then click OK.
PAGE 108
TANK-6000-C226 Em b e d d e d S ys te m Figure C-14: Select a Local Source Drive S te p 6: Select a source partition (Part 1) from basic drive as shown in Figure C-15. Then click OK. Figure C-15: Select a Source Partition from Basic Drive S te p 7: Select 1.2: [Recovery] NTFS drive and enter a file name called iei (Figure C-16). Click Save. The factory default image will then be saved in the selected recovery drive and named IEI.GHO. WARNING: The file name of the factory default image must be iei.GHO.
PAGE 109
TANK-6000-C226 Em b e d d e d S ys te m Figure C-16: File Name to Copy Image to S te p 8: When the Compress Image screen in Figure C-17 prompts, click High to make the image file smaller.
PAGE 110
TANK-6000-C226 Em b e d d e d S ys te m S te p 9: The Proceed with partition image creation window appears, click Yes to continue. Figure C-18: Image Creation Confirmation S te p 10: The Symantec Ghost starts to create the factory default image (Figure C-19). Figure C-19: Image Creation Complete S te p 11: When the image creation completes, a screen prompts as shown in Figure C-20. Click Continue and close the Ghost window to exit the program.
PAGE 111
TANK-6000-C226 Em b e d d e d S ys te m S te p 12: The recovery tool main menu window is shown as below. Press any key to reboot the system. Step0: Figure C-21: Press Any Key to Continue C.3 Au to Re c o ve ry S e tu p P ro c e d u re The auto recovery function allows a system to automatically restore from the factory default image after encountering a Blue Screen of Death (BSoD) or a hang for around 10 minutes. To use the auto recovery function, follow the steps described in the following sections.
PAGE 112
TANK-6000-C226 Em b e d d e d S ys te m Figure C-22: Auto Recovery Utility S te p 3: Reboot the system from the recovery CD. When prompted, press any key to boot from the recovery CD. It will take a while to launch the recovery tool. Please be patient! Figure C-23: Launching the Recovery Tool S te p 4: When the recovery tool setup menu appears, press <4> then .
PAGE 113
TANK-6000-C226 Em b e d d e d S ys te m S te p 5: The Symantec Ghost window appears and starts configuring the system to build an auto recovery partition. In this process the partition created for recovery files in Section C.2.2 is hidden and the auto recovery tool is saved in this partition. Figure C-25: Building the Auto Recovery Partition S te p 6: After completing the system configuration, the following message prompts to confirm whether to create a factory default image.
PAGE 114
TANK-6000-C226 Em b e d d e d S ys te m S te p 7: The Symantec Ghost starts to create the factory default image (Figure C-27). Figure C-27: Image Creation Complete S te p 8: After completing the system configuration, press any key in the following window to restart the system. Figure C-28: Press any key to continue S te p 9: Eject the One Key Recovery CD and restart the system. S te p 10: Press the key as soon as the system is turned on to enter the BIOS.
PAGE 115
TANK-6000-C226 Em b e d d e d S ys te m Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc. Advanced iEi Feature Auto Recovery Function [Disabled] Auto Recovery Function Reboot and recover system automatically within 10 min, when OS crashes. Please install Auto Recovery API service before enabling this function --------------------: Select Screen ↑ ↓: Select Item Enter Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit Version 2.
PAGE 116
TANK-6000-C226 Em b e d d e d S ys te m S te p 1: Hardware and BIOS setup. Refer to Section C.2.1. S te p 2: Install Linux operating system. Make sure to install GRUB (v0.97 or earlier) MBR type and Ext3 partition type. Leave enough space on the hard drive to create the recover partition later. NOTE: If the Linux OS is not installed with GRUB (v0.97 or earlier) and Ext3, the Symantec Ghost may not function properly.
PAGE 117
TANK-6000-C226 Em b e d d e d S ys te m DISKPART>sel disk 0 DISKPART>create part pri size= ___ DISKPART>assign letter=N DISKPART>exit system32>format N: /fs:ntfs /q /v:Recovery /y system32>exit S te p 4: Build the recovery partition. Press any key to boot from the recovery CD. It will take a while to launch the recovery tool. Please be patient. When the recovery tool setup menu appears, type <3> and press (Figure C-30).
PAGE 118
TANK-6000-C226 Em b e d d e d S ys te m Figure C-31: Access menu.lst in Linux (Text Mode) S te p 6: Modify the menu.lst as shown below. S te p 7: The recovery tool menu appears. (Figure C-32) Figure C-32: Recovery Tool Menu S te p 8: Create a factory default image. Follow Step 2 ~ Step 12 described in Section C.2.5 to create a factory default image.
PAGE 119
TANK-6000-C226 Em b e d d e d S ys te m C.5 Re c o ve ry To o l Fu n c tio n s After completing the initial setup procedures as described above, users can access the recovery tool by pressing while booting up the system. However, if the setup procedure in Section C.3 has been completed and the auto recovery function is enabled, the system will automatically restore from the factory default image without pressing the F3 key. The recovery tool main menu is shown below.
PAGE 120
TANK-6000-C226 Em b e d d e d S ys te m WARNING: All data in the system will be deleted during the system recovery. Please backup the system files before restoring the system (either Factory Restore or Restore Backup). C.5.1 Fa c to ry Re s to re To restore the factory default image, please follow the steps below. S te p 1: Type <1> and press in the main menu. S te p 2: The Symantec Ghost window appears and starts to restore the factory default. A factory default image called iei.
PAGE 121
TANK-6000-C226 Em b e d d e d S ys te m Figure C-35: Recovery Complete Window C.5.2 Ba c ku p S ys te m To backup the system, please follow the steps below. S te p 1: Type <2> and press in the main menu. S te p 2: The Symantec Ghost window appears and starts to backup the system. A backup image called iei_user.GHO is created in the hidden Recovery partition. Figure C-36: Backup System S te p 3: The screen shown in Figure C-37 appears when system backup is complete.
PAGE 122
TANK-6000-C226 Em b e d d e d S ys te m Figure C-37: System Backup Complete Window C.5.3 Re s to re Yo u r La s t Ba c ku p To restore the last system backup, please follow the steps below. S te p 1: Type <3> and press in the main menu. S te p 2: The Symantec Ghost window appears and starts to restore the last backup image (iei_user.GHO). Figure C-38: Restore Backup S te p 3: The screen shown in Figure C-39 appears when backup recovery is complete. Press any key to reboot the system.
PAGE 123
TANK-6000-C226 Em b e d d e d S ys te m Figure C-39: Restore System Backup Complete Window C.5.4 Ma n u a l To restore the last system backup, please follow the steps below. S te p 1: Type <4> and press in the main menu. S te p 2: The Symantec Ghost window appears. Use the Ghost program to backup or recover the system manually. Figure C-40: Symantec Ghost Window S te p 3: When backup or recovery is completed, press any key to reboot the system.
PAGE 124
TANK-6000-C226 Em b e d d e d S ys te m C.6 Re s to re S ys te m s fro m a Lin u x S e rve r thro u g h LAN The One Key Recovery allows a client system to automatically restore to a factory default image saved in a Linux system (the server) through LAN connectivity after encountering a Blue Screen of Death (BSoD) or a hang for around 10 minutes. To be able to use this function, the client system and the Linux system MUST reside in the same domain.
PAGE 125
TANK-6000-C226 Em b e d d e d S ys te m C.6.1 Co n fig u re DHCP S e rve r S e ttin g s S te p 1: Install the DHCP #yum install dhcp (CentOS, commands marked in red) #apt-get install dhcp3-server (Debian, commands marked in blue) S te p 2: Confirm the operating system default settings: dhcpd.conf. CentOS Use the following command to show the DHCP server sample location: #vi /etc/dhcpd.
PAGE 126
TANK-6000-C226 Em b e d d e d S ys te m filename “pxelinux.0”; C.6.2 Co n fig u re TFTP S e ttin g s S te p 1: Install the tftp, httpd and syslinux. #yum install tftp-server httpd syslinux (CentOS) #apt-get install tftpd-hpa xinetd syslinux (Debian) S te p 2: Enable the TFTP server by editing the “/etc/xinetd.d/tftp” file and make it use the remap file. The “-vvv” is optional but it could definitely help on getting more information while running the remap file. For example: CentOS #vi /etc/xinetd.
PAGE 127
TANK-6000-C226 Em b e d d e d S ys te m Debian Replace the TFTP settings from “inetd” to “xinetd” and annotate the “inetd” by adding “#”. #vi /etc/inetd.conf Modify: #tftp dgram udp wait root /usr/sbin....... (as shown below) #vi /etc/xinetd.d/tftp C.6.3 Co n fig u re On e Ke y Re c o ve ry S e rve r S e ttin g s S te p 1: Copy the Utility/RECOVERYR10.TAR.BZ2 package from the One Key Recovery CD to the system (server side). S te p 2: Extract the recovery package to /. #cp RecoveryR10.tar.
PAGE 128
TANK-6000-C226 Em b e d d e d S ys te m C.6.4 Sta rt th e DHCP, TFTP a n d HTTP Start the DHCP, TFTP and HTTP. For example: CentOS #service xinetd restart #service httpd restart #service dhcpd restart Debian #/etc/init.d/xinetd reload #/etc/init.d/xinetd restart #/etc/init.d/dhcp3-server restart C.6.5 Cre a te S ha re d Dire c to ry S te p 1: Install the samba. #yum install samba S te p 2: Create a shared directory for the factory default image. #mkdir /share #cd /share #mkdir /image #cp iei.
PAGE 129
TANK-6000-C226 Em b e d d e d S ys te m Modify: [image] comment = One Key Recovery path = /share/image browseable = yes writable = yes public = yes create mask = 0644 directory mask = 0755 S te p 4: Edit “/etc/samba/smb.conf” for your environment. For example: S te p 5: Modify the hostname #vi /etc/hostname Modify: RecoveryServer C.6.6 S e tu p a Clie n t S ys te m fo r Au to Re c o ve ry S te p 1: Configure the following BIOS options of the client system.
PAGE 130
TANK-6000-C226 Em b e d d e d S ys te m S te p 2: Continue to configure the Boot Option Priorities BIOS option of the client system: Boot Option #1  remain the default setting to boot from the original OS. Boot Option #2  select the boot from LAN option. S te p 3: Save changes and exit BIOS menu. Exit  Save Changes and Exit S te p 4: Install the auto recovery utility into the system by double clicking the Utility/AUTORECOVERY-SETUP.exe in the One Key Recovery CD.
PAGE 131
TANK-6000-C226 Em b e d d e d S ys te m NOTE: A firewall or a SELinux is not in use in the whole setup process. If there is a firewall or a SELinux protecting the system, modify the configuration information to accommodate them.
PAGE 132
TANK-6000-C226 Em b e d d e d S ys te m C.7 Oth e r In fo rm a tio n C.7.1 Us in g AHCI Mo d e o r ALi M5283 / VIA VT6421A Co n tro lle r When the system uses AHCI mode or some specific SATA controllers such as ALi M5283 or VIA VT6421A, the SATA RAID/AHCI driver must be installed before using one key recovery. Please follow the steps below to install the SATA RAID/AHCI driver. S te p 1: Copy the SATA RAID/AHCI driver to a floppy disk and insert the floppy disk into a USB floppy disk drive.
PAGE 133
TANK-6000-C226 Em b e d d e d S ys te m S te p 5: When the following window appears, press ~~to select “Specify Additional Device”. S te p 6: In the following window, select a SATA controller mode used in the system. Then press . The user can now start using the SATA HDD.~~
~~PAGE 134~~
TANK-6000-C226 Em b e d d e d S ys te m After pressing , the system will get into the recovery tool setup menu. S te p 7: Continue to follow the setup procedure from Step 4 in Section C.2.2 Create Partitions to finish the whole setup process.Step0: C.7.2 S ys te m Me m o ry Re q u ire m e n t To be able to access the recovery tool by pressing while booting up the system, please make sure to have enough system memory. The minimum memory requirement is listed below.
~~PAGE 135~~
~~TANK-6000-C226 Em b e d d e d S ys te m Ap p e n d ix D D Ha za rd o u s Ma te ria ls Dis c lo s u re P a g e 125~~
~~PAGE 136~~
TANK-6000-C226 Em b e d d e d S ys te m D.1 Ha za rd o u s Ma te ria ls Dis c lo s u re Ta ble for IP B P ro d u c ts Ce rtifie d a s Ro HS Co m p lia n t Un d e r 2002/95/EC With o u t Me rc u ry The details provided in this appendix are to ensure that the product is compliant with the Peoples Republic of China (China) RoHS standards. The table below acknowledges the presences of small quantities of certain materials in the product, and is applicable to China RoHS only.
~~PAGE 137~~
TANK-6000-C226 Em b e d d e d S ys te m P a rt Na m e To xic o r Ha za rd o u s S u b s ta n c e s a n d Ele m e n ts Le a d Me rc u ry Ca d m iu m He xa va le n t P o lyb ro m in a te d P o lyb ro m in a te d (P b ) (Hg ) (Cd ) Ch ro m iu m Bip h e n yls Dip h e n yl (CR(VI)) (P BB) Eth e rs (P BDE) Ho u s in g X O O O O X Dis p la y X O O O O X P rin te d Circ u it X O O O O X X O O O O O X O O O O X Fa n As s e m b ly X O O O O X P o we r S u p p ly
~~PAGE 138~~
TANK-6000-C226 Em b e d d e d S ys te m 此附件旨在确保本产品符合中国 RoHS 标准。以下表格标示此产品中某有毒物质的含量符合中国 RoHS 标准规定的限量要求。本产品上会附有”环境友好使用期限”的标签，此期限是估算这些物质”不会有泄漏或突变”的年限。本产品可能包含有较短的环境友好使用期限的可替换元件，像是电池或灯管，这些元件将会单独标示出来。部件名称有毒有害物质或元素铅汞镉六价铬多溴联苯多溴二苯 (P b ) (Hg ) (Cd ) (CR(VI)) (P BB) 醚 (P BDE) 壳体 X O O O O X 显示 X O O O O X 印刷电路板 X O O O O X 金属螺帽 X O O O O O 电缆组装 X O O O O X 风扇组装 X O O O O X 电力供应组装 X O O O O X 电池 O O O O O O O: 表示该有毒有害物质在该部件所有物质材料中的含量均在 S