Manual

ManualsBrandsIEI Integration ManualsComputer AccessoriesTANK-720-Q67

TANK-720 Embedded System

Page i

IEI Technology Corp.

User Manual

MODEL:

TANK-720

High Performance Fanless Embedded System with

2nd Gen Intel® Core™ i7/i5/i3, Celeron® and Pentium® desktop processors,

On-

board 2.0 GB DDR3 Memory, VGA/HDMI, USB 3.0, Dual Combo (SFP

Fiber/RJ -45) Gigabit LAN, Isolated CAN-bus, Audio and RoHS Compliant

Rev. 1.03 – 18 December 2012

Summary of content (147 pages)

PAGE 1
TANK-720 Em b e d de d S ys te m IEI Te c h n o lo g y Co rp . MODEL: TANK-720 Hig h P e rfo rm a n c e Fa n le s s Em b e d d e d S ys te m with 2n d Ge n In te l® Co re ™ i7/i5/i3, Ce le ro n ® a n d P e n tiu m ® d e s kto p p ro c e s s o rs , On -b o a rd 2.0 GB DDR3 Me m o ry, VGA/HDMI, US B 3.0, Du a l Co m b o (S FP Fib e r/RJ -45) Gig a b it LAN, Is o la te d CAN-b u s , Au d io a n d Ro HS Co m p lia n t Us e r Ma n u a l Page i Re v. 1.
PAGE 2
TANK-720 Em b e d d e d S ys te m Re vis io n Date Version Changes 18 December 2012 1.03 Update Section 3.9.11: Remote Control Terminal Block 21 June 2012 1.02 Update the system memory capacity 12 March 2012 1.01 Update the pictures for TANK-720 25 October 2011 1.
PAGE 3
TANK-720 Em b e d d e d S ys te m Co p yrig h t COP YRIGHT NOTICE The information in this document is subject to change without prior notice in order to improve reliability, design and function and does not represent a commitment on the part of the manufacturer. In no event will the manufacturer be liable for direct, indirect, special, incidental, or consequential damages arising out of the use or inability to use the product or documentation, even if advised of the possibility of such damages.
PAGE 4
TANK-720 Em b e d d e d S ys te m WARNING This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and(2) this device must accept any interference received, including interference that may cause undesired operation. NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules.
PAGE 5
TANK-720 Em b e d d e d S ys te m Ta b le o f Co n te n ts 1 INTRODUCTION.......................................................................................................... 1 1.1 OVERVIEW.................................................................................................................. 2 1.2 MODEL VARIATIONS ................................................................................................... 2 1.3 FEATURES ................................................................
PAGE 6
TANK-720 Em b e d d e d S ys te m 3.9.6 Digital I/O Connector ...................................................................................... 28 3.9.7 HDMI Connector ............................................................................................. 28 3.9.8 LAN Connectors ............................................................................................... 29 3.9.9 Power Input, 4-pin Terminal Block .................................................................. 31 3.9.
PAGE 7
TANK-720 Em b e d d e d S ys te m 4.3.3.1 CPU Information ....................................................................................... 56 4.3.4 SATA Configuration ......................................................................................... 57 4.3.5 USB Configuration........................................................................................... 59 4.3.6 Secondary Super IO Configuration .................................................................. 61 4.3.6.
PAGE 8
TANK-720 Em b e d d e d S ys te m A.5.4 Manual ............................................................................................................ 115 A.6 RESTORE SYSTEMS FROM A LINUX SERVER THROUGH LAN ...................................116 A.6.1 Configure DHCP Server Settings ................................................................... 117 A.6.2 Configure TFTP Settings ................................................................................ 118 A.6.
PAGE 9
TANK-720 Em b e d d e d S ys te m Lis t o f Fig u re s Figure 1-1: TANK-720 .....................................................................................................................2 Figure 1-2: TANK-720 Front Panel ................................................................................................6 Figure 1-3: TANK-720 Rear Panel .................................................................................................7 Figure 1-4: TANK-720 LED Indicators...................
PAGE 10
TANK-720 Em b e d d e d S ys te m Figure 3-26: RJ-45 RS-422/485 Serial Device Connection ........................................................35 Figure 3-27: RJ-45 RS-422/485 Serial Port Pinout Location .....................................................36 Figure 3-28: DB-9 Connector Pinout Location ..........................................................................36 Figure 3-29: Serial Device Connector .........................................................................................
PAGE 11
TANK-720 Em b e d d e d S ys te m Figure A-18: Image Creation Confirmation ..............................................................................102 Figure A-19: Image Creation Process.......................................................................................102 Figure A-20: Image Creation Complete ....................................................................................102 Figure A-21: Press Any Key to Continue .................................................................
PAGE 12
TANK-720 Em b e d d e d S ys te m Lis t o f Ta b le s Table 1-1: TANK-720 Model Variations .........................................................................................2 Table 1-2: Technical Specifications ..............................................................................................5 Table 3-1: Digital I/O Connector Pinouts ....................................................................................28 Table 3-2: HDMI Connector Pinouts ...................................
PAGE 13
TANK-720 Em b e d d e d S ys te m Ch a p te r 1 1 In tro d u c tio n Page 1
PAGE 14
TANK-720 Em b e d d e d S ys te m 1.1 Ove rvie w Figure 1-1: TANK-720 The TANK-720 Series fanless embedded system is powered by the 2nd Generation Intel® Core™ i7/i5/i3 and Pentium®/Celeron® desktop processor, uses the Intel® Q67 chipset and has 2.0 GB of DDR3 memory. It supports dual display via VGA and HDMI. One SATA 6Gb/s, two USB 3.0 and four USB 2.0 ports provide flexible expansion options. Serial device connectivity is provided by six RS-232 and two RS-422/485 ports. 1.
PAGE 15
TANK-720 Em b e d de d S ys te m 1.3 Fe a tu re s The TANK-720 features are listed below:  2nd Gen Intel® Core™ i7/i5/i3 and Pentium®/Celeron® desktop processor  Intel® HD graphics supports H.264/AVC-MPEG2/VC1, DirectX 10.1 and OpenGL 3.0  2.0 GB of DDR3 SDRAM SO-DIMM preinstalled  Dual combo (10/100/1000 baseT(X) or 1000 baseSPF slot) Gigabit LAN ports with Intel® AMT 7.0 support  8-channel audio/video capture support  Dual display via VGA and HDMI  Two USB 3.0 ports  Four USB 2.
PAGE 16
TANK-720 Em b e d d e d S ys te m S p e c ific a tio n s I/O a n d In d ic a to rs Eth e rn e t 2 x Combo (SFP Fiber/RJ-45) Gigabit LAN RS -232 4 x DB-9 serial ports on rear panel 2 x RJ-45 serial ports with isolation on front panel RS -422/RS -485 2 x RJ-45 serial ports with isolation on front panel US B In te rfa c e s 2 x USB 3.0 ports on front panel 4 x USB 2.
PAGE 17
TANK-720 Em b e d d e d S ys te m S p e c ific a tio n s SATA 6Gb/s with 2.5” HDD/SSD support S ATA P owe r 90W power adapter P owe r Ad a p te r Input: 100V AC~240V AC, 50/60 Hz Output: 19V DC Redundant dual DC input P owe r S u p p ly Power 1: 9V (+/-3%) ~ 36V Power 2: 10.5V (+/-3%) ~36 V P owe r Co n s u m p tio n 19V@3.
PAGE 18
TANK-720 Em b e d d e d S ys te m  2 x Wi-Fi antenna connectors An overview of the front panel is shown in Figure 1-2. Figure 1-2: TANK-720 Front Panel 1.5.2 Re a r P a n e l The TANK-720 rear panel contains: Page 6  1 x DIO port  1 x HDMI port  1 x Line-out port (green)  1 x Mic-in port (pink)  1 x 4-pin power jack for 10.
PAGE 19
TANK-720 Em b e d d e d S ys te m  2 x RJ-45 combo Gigabit LAN ports  4 x RS-232 serial ports  2 x SFP Fiber combo Gigabit LAN ports  4 x USB 2.0 ports  1 x VGA port  1 x Wi-Fi antenna connector An overview of the rear panel is shown in Figure 1-3 below.
PAGE 20
TANK-720 Em b e d d e d S ys te m NOTE: The TANK-720 provides two pairs of combo LANs. For each pair of combo LAN, only one LAN port can work at one time, and the SFP Fiber port works prior to the RJ-45 one. When a LAN port is working, the corresponding LED indicator lights up. Refer to Section 1.6 for the locations of the LED indicators. 1.6 LED In d ic a to rs There are several indicators on the front panel of the TANK-720 as shown in Figure 1-4.
PAGE 21
TANK-720 Em b e d d e d S ys te m 1.
PAGE 22
TANK-720 Em b e d d e d S ys te m Ch a p te r 2 2 Un p a c kin g P a g e 10
PAGE 23
TANK-720 Em b e d d e d S ys te m 2.1 An ti-s ta tic P re c a u tio n s WARNING: Failure to take ESD precautions during installation may result in permanent damage to the TANK-720 and severe injury to the user. Electrostatic discharge (ESD) can cause serious damage to electronic components, including the TANK-720. Dry climates are especially susceptible to ESD.
PAGE 24
TANK-720 Em b e d d e d S ys te m 2.3 Un pa c kin g Ch e c klis t NOTE: If some of the components listed in the checklist below are missing, please do not proceed with the installation. Contact the IEI reseller or vendor you purchased the TANK-720 from or contact an IEI sales representative directly. To contact an IEI sales representative, please send an email to sales@iei.com.tw.
PAGE 25
TANK-720 Em b e d d e d S ys te m Qu a n tity Ite m a n d P a rt Nu m b e r Im a g e S ta n d a rd 8 Chassis screw (P/N: 44013-030041-RS) 4 RJ-45 to DB-9 COM port cable (P/N: 32005-000200-200-RS) 3 Wi-Fi antenna (for Wi-Fi module only) (P/N: 32505-000900-100-RS) 1 Pluggable DC-in terminal block (P/N: 33502-000055-RS) 1 Pluggable CAN-bus terminal block (P/N: 33502-000007-RS) 1 Pluggable remote control terminal block (P/N: 33101-000422-RS) 1 User manual and driver CD 1 One Key Recovery CD 2
PAGE 26
TANK-720 Em b e d d e d S ys te m The following table lists the optional items that can be purchased separately. Op tio n a l Gigabit Ethernet SFP module (P/N: SFP1G-SX/-I SFP1G-MLX/-I SFP1G-LX10/-I SFP1G-ZX70/-I) Fiber cord (P/N: FPC-LCLC-MM3M FPC-LCLC-SS3M) OS: Win CE 6.
PAGE 27
TANK-720 Em b e d d e d S ys te m Ch a p te r 3 3 In s ta lla tio n P a g e 15
PAGE 28
TANK-720 Em b e d d e d S ys te m 3.1 In s ta lla tio n P re c a u tio n s During installation, be aware of the precautions below:  Read the user manual: The user manual provides a complete description of the TANK-720, installation instructions and configuration options.  DANGER! Disconnect Power: Power to the TANK-720 must be disconnected during the installation process, or before any attempt is made to access the rear panel.
PAGE 29
TANK-720 Em b e d d e d S ys te m Figure 3-1: Bottom Panel Retention Screws S te p 2: Remove the two HDD bracket retention screws (Figure 3-2). Figure 3-2: HDD Bracket Retention Screws S te p 3: Lift the HDD bracket out of the TANK-720 and put it on a flat surface. S te p 4: Attach the HDD to the HDD bracket. Secure the HDD with the HDD bracket by four retention screws (Figure 3-3).
PAGE 30
TANK-720 Em b e d d e d S ys te m Figure 3-3: HDD Installation S te p 5: Slide the HDD bracket to connect the HDD to the SATA connector. Secure the HDD bracket with TANK-720 by the two retention screws that were previously removed (Figure 3-4). Figure 3-4: HDD Bracket Installation S te p 6: Reinstall the bottom panel to the TANK-720. 3.
PAGE 31
TANK-720 Em b e d d e d S ys te m S te p 2: Align the pluggable CAN-bus terminal block with the CAN-bus terminal block connector on the TANK-720. S te p 3: Once aligned, insert the pluggable CAN-bus terminal block into the CAN-bus terminal block connector. S te p 4: Secure the pluggable CAN-bus terminal block to the external interface by tightening the two retention screws on either side of the terminal block (Figure 3-5). Figure 3-5: Pluggable CAN-bus Terminal Block Installation 3.
PAGE 32
TANK-720 Em b e d d e d S ys te m Figure 3-6: Pluggable DC-in Terminal Block Installation 3.5 P lu g g a b le Re m o te Co n tro l Te rm in a l Blo c k In s ta lla tio n To install the pluggable remote control terminal block, please follow the steps below: S te p 1: Locate the remote control terminal block connector. The location of the connector is shown in Figure 1-3. S te p 2: Align the pluggable remote control terminal block with the remote control terminal block connector on the TANK-720.
PAGE 33
TANK-720 Em b e d d e d S ys te m 3.6 S FP Mo d u le In s ta lla tio n To install an SFP module, please follow the steps below: S te p 1: Locate the SFP fiber connectors. The locations of the connectors are shown in Figure 1-3. S te p 2: Align the SFP module with one of the SFP fiber connectors on the TANK-720 (Figure 3-8). S te p 3: Once aligned, slide the SFP module into place (Figure 3-8).
PAGE 34
TANK-720 Em b e d d e d S ys te m 3.7 S O-DIMM In s ta lla tio n WARNING: Using incorrectly specified SO-DIMM may cause permanently damage the TANK-720. Please make sure the purchased SO-DIMM complies with the memory specifications of the TANK-720. To install a SO-DIMM into a SO-DIMM socket, please follow the steps below. S te p 1: Remove the bottom panel by removing the 10 retention screws from the bottom panel (Figure 3-1).
PAGE 35
TANK-720 Em b e d d e d S ys te m Figure 3-10: SO-DIMM Socket S te p 4: Align the SO-DIMM with the socket. The SO-DIMM must be oriented in such a way that the notch in the middle of the SO-DIMM must be aligned with the plastic bridge in the socket (Figure 3-11). S te p 5: Push the SO-DIMM into the socket at an angle (Figure 3-11). Figure 3-11: SO-DIMM Installation S te p 6: Gently pull the arms of the SO-DIMM socket out and push the rear of the SO-DIMM down (Figure 3-11).
PAGE 36
TANK-720 Em b e d d e d S ys te m S te p 8: Install the bracket that was previously removed in the same position it was before. S te p 9: Reinstall the bottom panel to the TANK-720. 3.8 Mo u n tin g th e S ys te m with Mo u n tin g Bra c ke ts To mount the embedded system onto a wall or some other surface using the two mounting brackets, please follow the steps below. S te p 1: Turn the embedded system over.
PAGE 37
TANK-720 Em b e d d e d S ys te m 3.9 Exte rn a l P e rip h e ra l In te rfa c e Co n n e c to rs The TANK-720 has the following connectors. Detailed descriptions of the connectors can be found in the subsections below.
PAGE 38
TANK-720 Em b e d d e d S ys te m 3.9.1 ACC Mo d e S witc h The TANK-720 allows turning the ACC mode on or off. The setting can be made through the ACC mode switch on the rear panel as shown below. Figure 3-13: ACC Mode Switch 3.9.2 AT/ATX P o we r Mo d e S witc h The TANK-720 supports AT and ATX power modes. The setting can be made through the AT/ATX power mode switch on the rear panel as shown below.
PAGE 39
TANK-720 Em b e d d e d S ys te m 3.9.3 Au d io Co n n e c to r CN La b e l: Lin e o u t and Mic CN Typ e : Audio jack CN Lo c a tio n : See Figure 3-15 The audio jacks connect to external audio devices.  Microphone (Pink): Connects a microphone.  Line Out port (Green): Connects to a headphone or a speaker. With multi-channel configurations, this port can also connect to front speakers. Figure 3-15: Audio Connector 3.9.
PAGE 40
TANK-720 Em b e d d e d S ys te m 3.9.6 Dig ita l I/O Co n n e c to r CN La b e l: DIO x 8 CN Typ e : DB-9 male connector CN Lo c a tio n : See Figure 1-3 CN P in o u ts : See Table 3-1 and Figure 3-17 The digital I/O connector provides programmable input and output for external devices. The pinouts for the digital I/O connector are listed in the table below.
PAGE 41
TANK-720 Em b e d d e d S ys te m Pin Description Pin Description 1 HDMI_DATA2 2 GND 3 HDMI_DATA2# 4 HDMI_DATA1 5 GND 6 HDMI_DATA1# 7 HDMI_DATA0 8 GND 9 HDMI_DATA0# 10 HDMI_CLK 11 GND 12 HDMI_CLK# 13 N/C 14 N/C 15 HDMI_SCL 16 HDMI_SDA 17 GND 18 +5V 19 HDMI_HPD 20 HDMI_GND 21 HDMI_GND 22 HDMI_GND 23 HDMI_GND Table 3-2: HDMI Connector Pinouts 3.9.
PAGE 42
TANK-720 Em b e d d e d S ys te m Figure 3-18: LAN Connection S te p 3: Insert the LAN cable RJ-45 connector. Once aligned, gently insert the LAN cable RJ-45 connector into the on-board RJ-45 connector. Pin Description Pin Description 1 TRD1P0 5 TRD1P2 2 TRD1N0 6 TRD1N2 3. TRD1P1 7 TRD1P3 4. TRD1N1 8 TRD1N3 Table 3-3: LAN Pinouts Figure 3-19: RJ-45 Ethernet Connector The RJ-45 Ethernet connector has two status LEDs, one green and one yellow.
PAGE 43
TANK-720 Em b e d d e d S ys te m Activity/Link LED Speed LED STATUS DESCRIPTION STATUS DESCRIPTION Off No link Off 10 Mbps connection Yellow Linked Green 100 Mbps connection Blinking TX/RX activity Orange 1 Gbps connection Table 3-4: RJ-45 Ethernet Connector LEDs 3.9.
PAGE 44
TANK-720 Em b e d d e d S ys te m The power connector connects to the 10.5V~36V DC power adapter. Figure 3-21: Power Input Connector Pin Description Pin Description 1 +12V 3 +12V 2 GND 4 GND Table 3-6: Power Input Pinouts 3.9.11 Re m o te Co n tro l Te rm in a l Blo c k (Fo r AT P o we r Mo d e On ly) CN La b e l: Remoter CN Typ e : 2-pin terminal block CN Lo c a tio n : See Figure 1-3 CN P in o u ts : See Figure 3-22 The 2-pin terminal block connects to a remote control device.
PAGE 45
TANK-720 Em b e d d e d S ys te m 3.9.12 RJ -45 RS -232 S e ria l P o rt Co n n e c to rs CN La b e l: RS 232 CN Typ e : RJ-45 CN Lo c a tio n : See Figure 1-2 CN P in o u ts : See Table 3-7, Table 3-8, Figure 3-24 and Figure 3-25 RS-232 serial port devices can be attached to the RJ-45 RS-232 serial ports on the front panel. S te p 1: Locate the RJ-45 RS-232 connectors. The locations of the RJ-45 RS-232 connectors are shown in Figure 1-2. S te p 2: Insert the RJ-45 connector.
PAGE 46
TANK-720 Em b e d d e d S ys te m Figure 3-24: RJ-45 RS-232 Serial Port Pinout Location Pin Description Pin Description 1 RI 5 RTS 2 DTR 6 RX 3. CTS 7 DSR 4.
PAGE 47
TANK-720 Em b e d d e d S ys te m 3.9.13 RJ -45 RS -422/485 S e ria l P o rt Co n n e c to rs CN La b e l: RS 422/485 CN Typ e : RJ-45 CN Lo c a tio n : See Figure 1-2 CN P in o u ts : See Table 3-9, Table 3-10, Figure 3-27 and Figure 3-28 RS-422/485 serial port devices can be attached to the RJ-45 RS-422/485 serial ports on the front panel. S te p 1: Locate the RJ-45 RS-422/485 connectors. The locations of the RJ-45 RS-422/485 connectors are shown in Figure 1-2.
PAGE 48
TANK-720 Em b e d d e d S ys te m Figure 3-27: RJ-45 RS-422/485 Serial Port Pinout Location Pin Description Pin Description 1 N/A 5 N/A 2 TXD485# 6 RXD485# 3. N/A 7 N/A 4.
PAGE 49
TANK-720 Em b e d d e d S ys te m 3.9.14 RS -232 S e ria l P o rt Co n n e c to rs CN La b e l: COM1, COM2, COM3 and COM4 CN Typ e : DB-9 connectors CN Lo c a tio n : See Figure 1-3 CN P in o u ts : See Table 3-11 and Figure 3-30 RS-232 serial port devices can be attached to the RS-232 serial ports on the rear panel. S te p 1: Locate the DB-9 connector. The locations of the DB-9 connectors are shown in Figure 1-3. S te p 2: Insert the serial connector.
PAGE 50
TANK-720 Em b e d d e d S ys te m Pin Description Pin Description 1 DCD 6 DSR 2 RX 7 RTS 3 TX 8 CTS 4 DTR 9 RI 5 GND Table 3-11: Serial Port Pinouts Figure 3-30: Serial Port Pinout Location 3.9.15 S FP Fib e r Co n n e c to rs The TANK-720 has two SFP fiber connectors. The locations of the connectors are shown in Figure 1-3. To install an SFP module, refer to Section 3.6. 3.9.
PAGE 51
TANK-720 Em b e d d e d S ys te m Figure 3-31: USB Device Connection S te p 3: Insert the device connector. Once aligned, gently insert the USB device connector into the USB connector on the TANK-720. Pin Description Pin Description 1 VCC 5 VCC 2 DATA- 6 DATA- 3 DATA+ 7 DATA+ 4 GROUND 8 GROUND Table 3-12: USB Port Pinouts 3.9.
PAGE 52
TANK-720 Em b e d d e d S ys te m S te p 1: Locate the female DB-15 connector. The location of the female DB-15 connector is shown in Figure 1-3. S te p 2: Align the VGA connector. Align the male DB-15 connector on the VGA screen cable with the female DB-15 connector on the external peripheral interface. S te p 3: Insert the VGA connector. Once the connectors are properly aligned with, insert the male connector from the VGA screen cable into the female connector on the TANK-720. See Figure 3-32.
PAGE 53
TANK-720 Em b e d d e d S ys te m Pin Description Pin Description 1 RED 2 GREEN 3 BLUE 4 NC 5 GND 6 GND 7 GND 8 GND 9 VCC / NC 10 GND 11 NC 12 DDC DAT 13 HSYNC 14 VSYNC 15 DDCCLK Table 3-13: VGA Connector Pinouts 3.10 P o we rin g On /Off th e S ys te m WARNING: Make sure a power supply with the correct input voltage is being fed into the system.
PAGE 54
TANK-720 Em b e d d e d S ys te m 3.11 Re d u n d a n t P o we r The TANK-720 is a system that supports redundant power. The redundant power input increases the reliability of the system and prevents data loss and system corruption from sudden power failure. The system can instantly and uninterruptedly switch to the second power input when the main power is unavailable or in low voltage capacity. There are two power connectors on the rear panel.
PAGE 55
TANK-720 Em b e d d e d S ys te m 3.11.1 ACC ON NOTE: In ACC On mode, the Power 1 connector must connect to ACC on signal to be able to control the system power. The ACC On mode is designed for vehicle applications. When the TANK-720 is in ACC On mode, the main power input is Power 1 connector and the backup power is from Power 2 connector. 3.11.1.
PAGE 56
TANK-720 Em b e d d e d S ys te m 3.11.1.2 S witc h to Ba c ku p P o we r During the operation, the system power will switch from Power 1 to Power 2 automatically when the following situations occur:  Power 1 < 9V and Power 2 > 10.5V  Power 1 > 9V, but the ACC ON signal jump from high to low  Power 1 is unplugged and Power 2 > 10.5V The following flow diagram shows how the power is switched between Power 1 and Power 2 and their LED statuses. Figure 3-38: ACC On: Switch Between PWR1 and PWR2 3.11.
PAGE 57
TANK-720 Em b e d d e d S ys te m NOTE: To turn on the system in the ATX power mode, press the Power button for three seconds. Press the Power button for six seconds to turn off the system. 3.11.2 ACC OFF When the TANK-720 is in ACC Off mode, the main power input is Power 2 connector and the backup power is from Power 1 connector. 3.11.2.1 Bo o t-u p When both power connectors are connected to a power source with over 9 V, the two power LEDs on the front panel turn on.
PAGE 58
TANK-720 Em b e d d e d S ys te m 3.11.2.2 S witc h to Ba c ku p P o we r During the operation, the system power will switch from Power 2 to Power 1 automatically when the following situations occur:  Power 2 < 10.5V and Power 1 > 9V  Power 2 is unplugged and Power 1 > 9V The following flow diagram shows how the power is switched between Power 2 and Power 1 and their LED statuses. Figure 3-42: ACC Off: Switch Between PWR1 and PWR2 3.11.2.
PAGE 59
TANK-720 Em b e d d e d S ys te m NOTE: The power LED turns off when the power cable is unplugged from the system.
PAGE 60
TANK-720 Em b e d d e d S ys te m Ch a p te r 4 4 BIOS P a g e 48
PAGE 61
TANK-720 Em b e d d e d S ys te m 4.1 In tro d u c tio n The BIOS is programmed onto the BIOS chip. The BIOS setup program allows changes to certain system settings. This chapter outlines the options that can be changed. 4.1.1 Sta rtin g S e tu p The UEFI BIOS is activated when the computer is turned on. The setup program can be activated in one of two ways. 1. Press the DEL or F2 key as soon as the system is turned on or 2.
PAGE 62
TANK-720 Em b e d d e d S ys te m Ke y Fu n c tio n F2 Previous values F3 Load optimized defaults F4 Save changes and Exit BIOS Table 4-1: BIOS Navigation Keys 4.1.3 Ge ttin g He lp When F1 is pressed a small help window describing the appropriate keys to use and the possible selections for the highlighted item appears. To exit the Help Window press ESC or the F1 key again. 4.1.
PAGE 63
TANK-720 Em b e d d e d S ys te m 4.2 Ma in The Main BIOS menu (BIOS Menu 1) appears when the BIOS Setup program is entered. The Main menu gives an overview of the basic system information. Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc. Main Advanced Chipset Boot Security Save & Exit BIOS Information BIOS Vendor Core Version Compliency Project Version Build Date and Time American Megatrends 4.6.4.0 UEFI 2.0 SC95AR11.ROM 10/27/2011 11:53:40 iWDD Vendor iWDD Version ICP SC95ER12.
PAGE 64
TANK-720 Em b e d d e d S ys te m  iWDD Ve rs io n  The iWDD Version displays the current iWDD version. The fields in iWDD Version cannot be changed.  Me m o ry In fo rm a tio n The Memory Information lists a brief summary of the on-board memory. The fields in Memory Information cannot be changed.  Total Memory: Displays the auto-detected system memory size and type.
PAGE 65
TANK-720 Em b e d d e d S ys te m Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc. Main Advanced Chipset Boot Security Save & Exit > > > > > > > > > > ACPI Settings Trusted Computing CPU Configuration SATA Configuration USB Configuration Second Super IO Configuration Super IO Configuration H/M Monitor Serial Port Console Redirection iEi Feature System ACPI Parameters ---------------------- : Select Screen ↑ ↓: Select Item Enter Select + - Change Opt.
PAGE 66
TANK-720 Em b e d d e d S ys te m  ACP I S le e p Sta te [S 1 (CP U Sto p Clo c k)] Use the ACPI Sleep State option to specify the sleep state the system enters when it is not being used.  Suspend Disabled  S1 (CPU Stop DEFAULT The system enters S1 (POS) sleep state. The system appears off. The CPU is stopped; RAM is Clock) refreshed; the system is running in a low power mode.  S3 (Suspend The caches are flushed and the CPU is powered to off. Power to the RAM is maintained.
PAGE 67
TANK-720 Em b e d d e d S ys te m  TP M S u p p o rt [Dis a b le ] Use the TPM Support option to configure support for the TPM.  Disable DEFAULT TPM support is disabled.  Enable TPM support is enabled. 4.3.3 CP U Co n fig u ra tio n Use the CPU Configuration menu (BIOS Menu 5) to view detailed CPU specifications and configure the CPU. Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc.
PAGE 68
TANK-720 Em b e d d e d S ys te m  In te l Virtu a liza tio n Te c h n o lo g y [Dis a b le d ] Use the Intel Virtualization Technology option to enable or disable virtualization on the system. When combined with third party software, Intel Virtualization technology allows several OSs to run on the same system at the same time.  Disabled DEFAULT Disables Intel Virtualization Technology.  Enables Intel Virtualization Technology. Enabled 4.3.3.
PAGE 69
TANK-720 Em b e d d e d S ys te m  Min CPU Speed: Lists the minimum CPU processing speed.  Processor Cores: Lists the number of the processor core  Intel HT Technology: Indicates if Intel HT Technology is supported by the CPU.  Intel VT-x Technology: Indicates if Intel VT-x Technology is supported by the CPU.  Intel SMX Technology: Indicates if Intel SMX Technology is supported by the CPU.  L1 Data Cache: Lists the amount of data storage space on the L1 cache.
PAGE 70
TANK-720 Em b e d d e d S ys te m   Disable  IDE Mode  RAID Mode Disables SATA devices. DEFAULT Configures SATA devices as normal IDE device. Configures SATA devices as RAID device. S e ria l-ATA Co n tro lle r 0 [Co m pa tib le ] Use the Serial-ATA Controller 0 option to configure the Serial-ATA controller mode when the SATA mode is set to IDE Mode.  Disable Disables Serial-ATA controller.  Enhanced Configures the Serial-ATA controller to be in enhanced mode.
PAGE 71
TANK-720 Em b e d d e d S ys te m 4.3.5 US B Co n fig u ra tio n Use the USB Configuration menu (BIOS Menu 8) to read USB configuration information and configure the USB settings. Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc. Advanced USB Configuration USB Support Parameters USB Devices: 1 Keyboard, 2 Hubs --------------------: Select Screen ↑ ↓: Select Item Enter Select + - Change Opt.
PAGE 72
TANK-720 Em b e d d e d S ys te m  Le g a c y US B3.0 S u p p o rt [En a b le d ] Use the USB3.0 Support option to enable or disable USB 3.0 support on the system.   Enabled  Disabled DEFAULT USB 3.0 support enabled USB 3.0 support disabled US B tra n s fe r tim e -o u t [20 s e c ] Use the USB transfer time-out option to set the USB transfer time-out.   1 sec Set the USB transfer time-out to 1 sec.  5 sec Set the USB transfer time-out to 5 sec.
PAGE 73
TANK-720 Em b e d d e d S ys te m 4.3.6 S e c o n d a ry S u p e r IO Co n fig u ra tio n Use the Secondary Super IO Configuration menu (BIOS Menu 9) to set or change the configurations for the serial ports. Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc.
PAGE 74
TANK-720 Em b e d d e d S ys te m 4.3.6.1.1 S e ria l P o rt 7 Co n fig u ra tio n  S e ria l P o rt [En a b le d ] Use the Serial Port option to enable or disable the serial port.   Disabled  Enabled Disable the serial port DEFAULT Enable the serial port Ch a n g e S e ttin g s [Au to ] Use the Change Settings option to change the serial port IO port address and interrupt address.  Auto DEFAULT The serial port IO port address and interrupt address are automatically detected.
PAGE 75
TANK-720 Em b e d d e d S ys te m   Disabled  Enabled Disable the serial port DEFAULT Enable the serial port Ch a n g e S e ttin g s [Au to ] Use the Change Settings option to change the serial port IO port address and interrupt address.  Auto DEFAULT The serial port IO port address and interrupt address are automatically detected.
PAGE 76
TANK-720 Em b e d d e d S ys te m 4.3.7 S u p e r IO Co n fig u ra tio n Use the Super IO Configuration menu (BIOS Menu 11) to set or change the configurations for the serial ports. Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc.
PAGE 77
TANK-720 Em b e d d e d S ys te m 4.3.7.1.1 S e ria l P o rt 1 Co n fig u ra tio n  S e ria l P o rt [En a b le d ] Use the Serial Port option to enable or disable the serial port.   Disabled  Enabled Disable the serial port DEFAULT Enable the serial port Ch a n g e S e ttin g s [Au to ] Use the Change Settings option to change the serial port IO port address and interrupt address.  Auto DEFAULT The serial port IO port address and interrupt address are automatically detected.
PAGE 78
TANK-720 Em b e d d e d S ys te m   Enabled DEFAULT Enable the serial port Ch a n g e S e ttin g s [Au to ] Use the Change Settings option to change the serial port IO port address and interrupt address.  Auto DEFAULT The serial port IO port address and interrupt address are automatically detected.
PAGE 79
TANK-720 Em b e d d e d S ys te m  Auto DEFAULT The serial port IO port address and interrupt address are automatically detected.
PAGE 80
TANK-720 Em b e d d e d S ys te m    IO=2E8h; Serial Port I/O port address is 2E8h and the interrupt IRQ=10, 11 address is IRQ10, 11 IO=2D0h; Serial Port I/O port address is 2D0h and the interrupt IRQ=10, 11 address is IRQ10, 11 IO=2D8h; Serial Port I/O port address is 2D8h and the interrupt IRQ=10, 11 address is IRQ10, 11 4.3.7.1.5 S e ria l P o rt 5 Co n fig u ra tio n  S e ria l P o rt [En a b le d ] Use the Serial Port option to enable or disable the serial port.
PAGE 81
TANK-720 Em b e d d e d S ys te m   IO=2E0h; Serial Port I/O port address is 2E0h and the interrupt IRQ=10, 11 address is IRQ10, 11 De vic e Mo d e [RS 422/485] Use the Device Mode option to set the serial port to normal or RS-422/485 communications..  Normal  RS422/485 Sets the serial port mode to normal. DEFAULT Enables serial port RS-422/485 support. 4.3.7.1.
PAGE 82
TANK-720 Em b e d d e d S ys te m     IO=2D0h; Serial Port I/O port address is 2D0h and the interrupt IRQ=10, 11 address is IRQ10, 11 IO=2D8h; Serial Port I/O port address is 2D8h and the interrupt IRQ=10, 11 address is IRQ10, 11 IO=2E0h; Serial Port I/O port address is 2E0h and the interrupt IRQ=10, 11 address is IRQ10, 11 De vic e Mo d e [RS 422/485] Use the Device Mode option to set the serial port to normal or RS-422/485 communications..
PAGE 83
TANK-720 Em b e d d e d S ys te m  P C He a lth Sta tu s The following system parameters and values are shown. The system parameters that are monitored are:  System Temperatures: o o  CPU Temperature System Temperature Voltages: o o o o o o o o V3.3S CPU_CORE +V5S +V12S +1.5V_DDR3 VSB3V VBAT 5VSB 4.3.9 S e ria l P o rt Co n s o le Re d ire c tio n The Serial Port Console Redirection menu (BIOS Menu 14) allows the console redirection options to be configured.
PAGE 84
TANK-720 Em b e d d e d S ys te m Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc.
PAGE 85
TANK-720 Em b e d d e d S ys te m 4.3.10 iEi Fe a tu re Use the iEi Feature menu (BIOS Menu 15) to configure the iEi features. Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc. Advanced iEi Feature Auto Recovery Function [Disabled] Auto Recovery Function Reboot and recover system automatically within 10 min, when OS crashes. Please install Auto Recovery API service before enabling this function. --------------------: Select Screen ↑ ↓: Select Item Enter Select + - Change Opt.
PAGE 86
TANK-720 Em b e d d e d S ys te m 4.4 Ch ips e t Use the Chipset menu (BIOS Menu 16) to access the Northbridge and Southbridge configuration menus. WARNING! Setting the wrong values for the Chipset BIOS selections in the Chipset BIOS menu may cause the system to malfunction. Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc.
PAGE 87
TANK-720 Em b e d d e d S ys te m 4.4.1 No rth Brid g e Use the North Bridge menu (BIOS Menu 17) to configure the Northbridge chipset. Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc. Chipset Memory Information Config Graphics Settings. Total Memory 2048 MB (DDR3 1333) Memory Slot Onboard Memory 0 MB (DDR3 1333) 2048 MB (DDR3 1333) --------------------: Select Screen ↑ ↓: Select Item > Intel IGD SWSCI OpRegion Enter Select + - Change Opt.
PAGE 88
TANK-720 Em b e d d e d S ys te m Use the DVMT Mode Select option to select the Intel Dynamic Video Memory Technology (DVMT) operating mode.  A fixed portion of graphics memory is reserved as Fixed Mode graphics memory.  DVMT Mode DEFAULT Graphics memory is dynamically allocated according to the system and graphics needs.  DVMT Me m o ry [256MB] Use the DVMT Memory option to specify the maximum amount of memory that can be allocated as graphics memory. Configuration options are listed below.
PAGE 89
TANK-720 Em b e d d e d S ys te m Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc. Chipset Auto Power Button Status [OFF] USB Controller USB3.
PAGE 90
TANK-720 Em b e d d e d S ys te m   Disabled  Enabled DEFAULT Disables Intel 82583V PXE Boot option Enables Intel 82583V PXE Boot option In te l 82579LM P XE Bo o t [Dis a b le d ] Use the Intel 82579LM PXE Boot option to enable or disable the boot option for the Intel 82579LM PXE.
PAGE 91
TANK-720 Em b e d d e d S ys te m  Wa ke o n Gb e LAN [En a b le d ] Use the Wake on Gbe LAN option to enable or disable wake on Gbe LAN.   Disabled  Enabled Disables wake on Gbe LAN DEFAULT Enables wake on Gbe LAN Re s to re AC P owe r Lo s s [La s t Sta te ] Use the Restore AC Power Loss option to specify what state the system returns to if there is a sudden loss of power to the system.
PAGE 92
TANK-720 Em b e d d e d S ys te m  MEBx Mo d e [No rm a l] Use the MEBx Mode option to configure MEBx Mode options.  Normal  Hidden DEFAULT Enables normal mode Enables hidden Ctrl+P function Ctrl + P  Enables user to enter MEBx setup Enter MEBx Setup  Un c o n fig u re AMT/ME [Dis a b le d ] Use the Unconfigure AMT/ME option to perform AMT/ME unconfigure without password operation.  Disabled  Enabled DEFAULT Not perform AMT/ME unconfigure To perform AMT/ME unconfigure 4.
PAGE 93
TANK-720 Em b e d d e d S ys te m  Bo o tu p Nu m Lo c k Sta te [On ] Use the Bootup NumLock State BIOS option to specify if the number lock setting must be modified during boot up.  On DEFAULT Allows the Number Lock on the keyboard to be enabled automatically when the computer system boots up. This allows the immediate use of the 10-key numeric keypad located on the right side of the keyboard. To confirm this, the Number Lock LED light on the keyboard is lit.
PAGE 94
TANK-720 Em b e d d e d S ys te m  In te rru p t 19 Ca p tu re [Dis a b le d ] Use the Interrupt 19 Capture option to s enable or disable interrupt 19 capture.  Force DEFAULT Enables interrupt 19 capture. BIOS  Keep Disables interrupt 19 capture. Current  Bo o t Op tio n #1 [S ATA S M: IEI Te c h …] Use Boot Option #1 to enable or disable booting from the detected drive.  SATA SM: IEI Tech… DEFAULT Enables booting from the detected storage device.   Disabled Disables boot option.
PAGE 95
TANK-720 Em b e d d e d S ys te m Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc. Main Advanced Chipset Boot Security Save & Exit Password Description Set Setup Administrator Password If ONLY the Administrator’s password is set, then this only limits access to Setup and is only asked for when entering Setup. If ONLY the User’s password is set, then this is a power on password and must be entered to boot or enter Setup. In Setup the User will have Administrator rights.
PAGE 96
TANK-720 Em b e d d e d S ys te m 4.7 Exit Use the Exit menu (BIOS Menu 23) to load default BIOS values, optimal failsafe values and to save configuration changes. Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc. Main Advanced Chipset Boot Security Save & Exit Save Changes and Reset Discard Changes and Reset Exit the system after saving the changes.
PAGE 97
TANK-720 Em b e d d e d S ys te m  S a ve a s Us e r De fa u lts Use the Save as User Defaults option to save the changes done so far as user defaults.  Re s to re Us e r De fa u lts Use the Restore User Defaults option to restore the user defaults to all the setup options.
PAGE 98
TANK-720 Em b e d d e d S ys te m Ap p e n d ix A A On e Ke y Re c o ve ry P a g e 86
PAGE 99
TANK-720 Em b e d d e d S ys te m A.1 On e Ke y Re c o ve ry In tro d u c tio n The IEI one key recovery is an easy-to-use front end for the Norton Ghost system backup and recovery tool. This tool provides quick and easy shortcuts for creating a backup and reverting to that backup or reverting to the factory default settings.
PAGE 100
TANK-720 Em b e d d e d S ys te m After completing the five initial setup procedures as described above, users can access the recovery tool by pressing while booting up the system. The detailed information of each function is described in Section A.5. NOTE: The initial setup procedures for Linux system are described in Section A.3. A.1.1 S ys te m Re q u ire m e n t NOTE: The recovery CD can only be used with IEI products.
PAGE 101
TANK-720 Em b e d d e d S ys te m partitions. Please take the following table as a reference when calculating the size of the partition. OS OS Image after Ghost Compression Ratio Windows® 7 7 GB 5 GB 70% Windows® XPE 776 MB 560 MB 70% Windows® CE 6.0 36 MB 28 MB 77% NOTE: Specialized tools are required to change the partition size if the operating system is already installed. A.1.
PAGE 102
TANK-720 Em b e d d e d S ys te m o o o o o o o Ubuntu 8.10 (Intrepid) Ubuntu 7.10 (Gutsy) Ubuntu 6.10 (Edgy) Debian 5.0 (Lenny) Debian 4.0 (Etch) SuSe 11.2 SuSe 10.3 NOTE: Installing unsupported OS versions may cause the recovery tool to fail. A.2 S e tu p P ro c e d u re fo r Win d o ws Prior to using the recovery tool to backup or restore Windows system, a few setup procedures are required. S te p 1: Hardware and BIOS setup (see Section A.2.1) S te p 2: Create partitions (see Section A.2.
PAGE 103
TANK-720 Em b e d d e d S ys te m A.2.1 Ha rd wa re a n d BIOS S e tu p S te p 1: Make sure the system is powered off and unplugged. S te p 2: Install a hard drive or SSD in the system. An unformatted and unpartitioned disk is recommended. S te p 3: Connect an optical disk drive to the system and insert the recovery CD. S te p 4: Turn on the system. S te p 5: Press the key as soon as the system is turned on to enter the BIOS.
PAGE 104
TANK-720 Em b e d d e d S ys te m Figure A-2: Launching the Recovery Tool S te p 3: The recovery tool setup menu is shown as below. Figure A-3: Recovery Tool Setup Menu S te p 4: P a g e 92 Press <6> then .
PAGE 105
TANK-720 Em b e d d e d S ys te m Figure A-4: Command Mode S te p 5: The command prompt window appears. Type the following commands (marked in red) to create two partitions. One is for the OS installation; the other is for saving recovery files and images which will be an invisible partition.
PAGE 106
TANK-720 Em b e d d e d S ys te m Figure A-5: Partition Creation Commands P a g e 94
PAGE 107
TANK-720 Em b e d d e d S ys te m NOTE: Use the following commands to check if the partitions were created successfully. S te p 6: Press any key to exit the recovery tool and automatically reboot the system. Please continue to the following procedure: Build-up Recovery Partition. A.2.3 In s ta ll Op e ra tin g S ys te m , Drive rs a n d Ap p lic a tio n s Install the operating system onto the unlabelled partition.
PAGE 108
TANK-720 Em b e d d e d S ys te m A.2.4 Bu ild -u p Re c o ve ry P a rtitio n S te p 1: Put the recover CD in the optical drive. S te p 2: Start the system. S te p 3: Boot the system from recovery CD. When prompted, press any key to boot from the recovery CD. It will take a while to launch the recovery tool. Please be patient! Figure A-6: Launching the Recovery Tool S te p 4: When the recovery tool setup menu appears, press <2> then .
PAGE 109
TANK-720 Em b e d d e d S ys te m S te p 5: The Symantec Ghost window appears and starts configuring the system to build a recovery partition. In this process the partition created for recovery files in Section A.2.2 is hidden and the recovery tool is saved in this partition. Figure A-8: Building the Recovery Partition S te p 6: After completing the system configuration, press any key in the following window to reboot the system. Figure A-9: Press Any Key to Continue S te p 7: Eject the recovery CD.
PAGE 110
TANK-720 Em b e d d e d S ys te m A.2.5 Cre a te Fa c to ry De fa u lt Im a g e NOTE: Before creating the factory default image, please configure the system to a factory default environment, including driver and application installations. To create a factory default image, please follow the steps below. S te p 1: Turn on the system. When the following screen displays (Figure A-10), press the key to access the recovery tool.
PAGE 111
TANK-720 Em b e d d e d S ys te m Figure A-12: About Symantec Ghost Window S te p 4: Use mouse to navigate to the option shown below (Figure A-13). Figure A-13: Symantec Ghost Path S te p 5: Select the local source drive (Drive 1) as shown in Figure A-14. Then click OK.
PAGE 112
TANK-720 Em b e d d e d S ys te m Figure A-14: Select a Local Source Drive S te p 6: Select a source partition (Part 1) from basic drive as shown in Figure A-15. Then click OK. Figure A-15: Select a Source Partition from Basic Drive S te p 7: Select 1.2: [Recovery] NTFS drive and enter a file name called iei (Figure A-16). Click Save. The factory default image will then be saved in the selected recovery drive and named IEI.GHO. WARNING: The file name of the factory default image must be iei.GHO.
PAGE 113
TANK-720 Em b e d d e d S ys te m Figure A-16: File Name to Copy Image to S te p 8: When the Compress Image screen in Figure A-17 prompts, click High to make the image file smaller.
PAGE 114
TANK-720 Em b e d d e d S ys te m S te p 9: The Proceed with partition image creation window appears, click Yes to continue. Figure A-18: Image Creation Confirmation S te p 10: The Symantec Ghost starts to create the factory default image (Figure A-19). Figure A-19: Image Creation Process S te p 11: When the image creation completes, a screen prompts as shown in Figure A-20. Click Continue and close the Ghost window to exit the program.
PAGE 115
TANK-720 Em b e d d e d S ys te m S te p 12: The recovery tool main menu window is shown as below. Press any key to reboot the system. Step0: Figure A-21: Press Any Key to Continue A.3 Au to Re c o ve ry S e tu p P ro c e d u re The auto recovery function allows a system to automatically restore from the factory default image after encountering a Blue Screen of Death (BSoD) or a hang for around 10 minutes. To use the auto recovery function, follow the steps described in the following sections.
PAGE 116
TANK-720 Em b e d d e d S ys te m Figure A-22: Auto Recovery Utility S te p 3: Reboot the system from the recovery CD. When prompted, press any key to boot from the recovery CD. It will take a while to launch the recovery tool. Please be patient! Figure A-23: Launching the Recovery Tool S te p 4: When the recovery tool setup menu appears, press <4> then .
PAGE 117
TANK-720 Em b e d d e d S ys te m S te p 5: The Symantec Ghost window appears and starts configuring the system to build an auto recovery partition. In this process the partition created for recovery files in Section A.2.2 is hidden and the auto recovery tool is saved in this partition. Figure A-25: Building the Auto Recovery Partition S te p 6: After completing the system configuration, the following message prompts to confirm whether to create a factory default image.
PAGE 118
TANK-720 Em b e d d e d S ys te m S te p 7: The Symantec Ghost starts to create the factory default image (Figure A-27). Figure A-27: Image Creation Complete S te p 8: After completing the system configuration, press any key in the following window to restart the system. Figure A-28: Press any key to continue S te p 9: Eject the One Key Recovery CD and restart the system. S te p 10: Press the key as soon as the system is turned on to enter the BIOS.
PAGE 119
TANK-720 Em b e d d e d S ys te m Main Advanced PCIPNP BIOS SETUP UTILITY Boot Security Chipset Exit iEi Feature  Auto Recovery Function [Enabled] Recover from PXE [Disabled]  ↑ ↓ Enter F1 F10 ESC Select Screen Select Item Go to SubScreen General Help Save and Exit Exit v02.61 ©Copyright 1985-2006, American Megatrends, Inc. BIOS Menu 24: IEI Feature S te p 12: Save changes and restart the system.
PAGE 120
TANK-720 Em b e d d e d S ys te m Install Linux operating system. Make sure to install GRUB (v0.97 or earlier) S te p 2: MBR type and Ext3 partition type. Leave enough space on the hard drive to create the recover partition later. NOTE: If the Linux OS is not installed with GRUB (v0.97 or earlier) and Ext3, the Symantec Ghost may not function properly.
PAGE 121
TANK-720 Em b e d d e d S ys te m DISKPART>create part pri size= ___ DISKPART>assign letter=N DISKPART>exit system32>format N: /fs:ntfs /q /v:Recovery /y system32>exit S te p 4: Build-up recovery partition. Press any key to boot from the recovery CD. It will take a while to launch the recovery tool. Please be patient. When the recovery tool setup menu appears, type <3> and press (Figure A-30). The Symantec Ghost window appears and starts configuring the system to build-up a recovery partition.
PAGE 122
TANK-720 Em b e d d e d S ys te m Figure A-31: Access menu.lst in Linux (Text Mode) S te p 6: Modify the menu.lst as shown below. S te p 7: The recovery tool menu appears. (Figure A-32) Figure A-32: Recovery Tool Menu S te p 8: Create a factory default image. Follow Step 2 ~ Step 12 described in Section A.2.5 to create a factory default image.
PAGE 123
TANK-720 Em b e d d e d S ys te m A.5 Re c o ve ry To o l Fu n c tio n s After completing the initial setup procedures as described above, users can access the recovery tool by pressing while booting up the system. However, if the setup procedure in Section A.3 has been completed and the auto recovery function is enabled, the system will automatically restore from the factory default image without pressing the F3 key. The recovery tool main menu is shown below.
PAGE 124
TANK-720 Em b e d d e d S ys te m WARNING: All data in the system will be deleted during the system recovery. Please backup the system files before restoring the system (either Factory Restore or Restore Backup). A.5.1 Fa c to ry Re s to re To restore the factory default image, please follow the steps below. S te p 1: Type <1> and press in the main menu. S te p 2: The Symantec Ghost window appears and starts to restore the factory default. A factory default image called iei.
PAGE 125
TANK-720 Em b e d d e d S ys te m Figure A-35: Recovery Complete Window A.5.2 Ba c ku p S ys te m To backup the system, please follow the steps below. S te p 1: Type <2> and press in the main menu. S te p 2: The Symantec Ghost window appears and starts to backup the system. A backup image called iei_user.GHO is created in the hidden Recovery partition. Figure A-36: Backup System S te p 3: The screen is shown as in Figure A-37 when system backup is completed.
PAGE 126
TANK-720 Em b e d d e d S ys te m Figure A-37: System Backup Complete Window A.5.3 Re s to re Yo u r La s t Ba c ku p To restore the last system backup, please follow the steps below. S te p 1: Type <3> and press in the main menu. S te p 2: The Symantec Ghost window appears and starts to restore the last backup image (iei_user.GHO). Figure A-38: Restore Backup S te p 3: The screen is shown as in Figure A-39 when backup recovery is completed. Press any key to reboot the system.
PAGE 127
TANK-720 Em b e d d e d S ys te m Figure A-39: Restore System Backup Complete Window A.5.4 Ma n u a l To restore the last system backup, please follow the steps below. S te p 1: Type <4> and press in the main menu. S te p 2: The Symantec Ghost window appears. Use the Ghost program to backup or recover the system manually. Figure A-40: Symantec Ghost Window S te p 3: When backup or recovery is completed, press any key to reboot the system.
PAGE 128
TANK-720 Em b e d d e d S ys te m A.6 Re s to re S ys te m s fro m a Lin u x S e rve r th ro u g h LAN The One Key Recovery allows a client system to automatically restore to a factory default image saved in a Linux system (the server) through LAN connectivity after encountering a Blue Screen of Death (BSoD) or a hang for around 10 minutes. To be able to use this function, the client system and the Linux system MUST reside in the same domain.
PAGE 129
TANK-720 Em b e d d e d S ys te m A.6.1 Co n fig u re DHCP S e rve r S e ttin g s S te p 1: Install the DHCP #yum install dhcp (CentOS, commands marked in red) #apt-get install dhcp3-server (Debian, commands marked in blue) S te p 2: Confirm the operating system default settings: dhcpd.conf. CentOS Use the following command to show the DHCP server sample location: #vi /etc/dhcpd.conf The DHCP server sample location is shown as below: Use the following command to copy the DHCP server sample to etc/dhcpd.
PAGE 130
TANK-720 Em b e d d e d S ys te m filename “pxelinux.0”; A.6.2 Co n fig u re TFTP S e ttin g s S te p 1: Install the tftp, httpd and syslinux. #yum install tftp-server httpd syslinux (CentOS) #apt-get install tftpd-hpa xinetd syslinux (Debian) S te p 2: Enable the TFTP server by editing the “/etc/xinetd.d/tftp” file and make it use the remap file. The “-vvv” is optional but it could definitely help on getting more information while running the remap file. For example: CentOS #vi /etc/xinetd.
PAGE 131
TANK-720 Em b e d d e d S ys te m Debian Replace the TFTP settings from “inetd” to “xinetd” and annotate the “inetd” by adding “#”. #vi /etc/inetd.conf Modify: #tftp dgram udp wait root /usr/sbin....... (as shown below) #vi /etc/xinetd.d/tftp A.6.3 Co n fig u re On e Ke y Re c o ve ry S e rve r S e ttin g s S te p 1: Copy the Utility/RECOVERYR10.TAR.BZ2 package from the One Key Recovery CD to the system (server side). S te p 2: Extract the recovery package to /. #cp RecoveryR10.tar.
PAGE 132
TANK-720 Em b e d d e d S ys te m A.6.4 Sta rt th e DHCP, TFTP a n d HTTP Start the DHCP, TFTP and HTTP. For example: CentOS #service xinetd restart #service httpd restart #service dhcpd restart Debian #/etc/init.d/xinetd reload #/etc/init.d/xinetd restart #/etc/init.d/dhcp3-server restart A.6.5 Cre a te S h a re d Dire c to ry S te p 1: Install the samba. #yum install samba S te p 2: Create a shared directory for the factory default image. #mkdir /share #cd /share #mkdir /image #cp iei.
PAGE 133
TANK-720 Em b e d d e d S ys te m Modify: [image] comment = One Key Recovery path = /share/image browseable = yes writable = yes public = yes create mask = 0644 directory mask = 0755 S te p 4: Edit “/etc/samba/smb.conf” for your environment. For example: S te p 5: Modify the hostname #vi /etc/hostname Modify: RecoveryServer A.6.6 S e tu p a Clie n t S ys te m fo r Au to Re c o ve ry S te p 1: Configure the following BIOS options of the client system.
PAGE 134
TANK-720 Em b e d d e d S ys te m S te p 2: Continue to configure the Boot Option Priorities BIOS option of the client system: Boot Option #1  remain the default setting to boot from the original OS. Boot Option #2  select the boot from LAN option. S te p 3: Save changes and exit BIOS menu. Exit  Save Changes and Exit S te p 4: Install the auto recovery utility into the system by double clicking the Utility/AUTORECOVERY-SETUP.exe in the One Key Recovery CD.
PAGE 135
TANK-720 Em b e d d e d S ys te m NOTE: A firewall or a SELinux is not in use in the whole setup process. If there is a firewall or a SELinux protecting the system, modify the configuration information to accommodate them.
PAGE 136
TANK-720 Em b e d d e d S ys te m A.7 Oth e r In fo rm a tio n A.7.1 Us in g AHCI Mo d e o r ALi M5283 / VIA VT6421A Co n tro lle r When the system uses AHCI mode or some specific SATA controllers such as ALi M5283 or VIA VT6421A, the SATA RAID/AHCI driver must be installed before using one key recovery. Please follow the steps below to install the SATA RAID/AHCI driver. S te p 1: Copy the SATA RAID/AHCI driver to a floppy disk and insert the floppy disk into a USB floppy disk drive.
PAGE 137
TANK-720 Em b e d d e d S ys te m S te p 5: When the following window appears, press ~~to select “Specify Additional Device”. S te p 6: In the following window, select a SATA controller mode used in the system. Then press . The user can now start using the SATA HDD.~~
~~PAGE 138~~
TANK-720 Em b e d d e d S ys te m After pressing , the system will get into the recovery tool setup menu. S te p 7: Continue to follow the setup procedure from Step 4 in Section A.2.2 Create Partitions to finish the whole setup process.Step0: A.7.2 S ys te m Me m o ry Re q u ire m e n t To be able to access the recovery tool by pressing while booting up the system, please make sure to have enough system memory. The minimum memory requirement is listed below.
~~PAGE 139~~
~~TANK-720 Em b e d d e d S ys te m Ap p e n d ix B B S a fe ty P re c a u tio n s P a g e 127~~
~~PAGE 140~~
TANK-720 Em b e d d e d S ys te m B.1 S a fe ty P re c a u tio n s WARNING: The precautions outlined in this appendix should be strictly followed. Failure to follow these precautions may result in permanent damage to the TANK-720. Please follow the safety precautions outlined in the sections that follow: B.1.1 Ge n e ra l S a fe ty P re c a u tio n s Please ensure the following safety precautions are adhered to at all times.
~~PAGE 141~~
TANK-720 Em b e d d e d S ys te m B.1.2 An ti-s ta tic P re c a u tio n s WARNING: Failure to take ESD precautions during the installation of the TANK-720 may result in permanent damage to the TANK-720 and severe injury to the user. Electrostatic discharge (ESD) can cause serious damage to electronic components, including the TANK-720. Dry climates are especially susceptible to ESD.
~~PAGE 142~~
TANK-720 Em b e d d e d S ys te m B.1.3 P ro d u c t Dis p o s a l CAUTION: Risk of explosion if battery is replaced by and incorrect type. Only certified engineers should replace the on-board battery. Dispose of used batteries according to instructions and local regulations.  Outside the European Union - If you wish to dispose of used electrical and electronic products outside the European Union, please contact your local authority so as to comply with the correct disposal method.
~~PAGE 143~~
TANK-720 Em b e d d e d S ys te m  Be cautious of all small removable components when vacuuming the TANK-720.  Turn the TANK-720 off before cleaning the TANK-720.  Never drop any objects or liquids through the openings of the TANK-720.  Be cautious of any possible allergic reactions to solvents or chemicals used when cleaning the TANK-720.  Avoid eating, drinking and smoking within vicinity of the TANK-720. B.2.
~~PAGE 144~~
~~TANK-720 Em b e d d e d S ys te m Ap p e n d ix C C Ha za rd o u s Ma te ria ls Dis c lo s u re P a g e 132~~
~~PAGE 145~~
TANK-720 Em b e d d e d S ys te m C.1 Ha za rd o u s Ma te ria ls Dis c lo s u re Ta b le fo r IP B P ro d u c ts Ce rtifie d a s Ro HS Co m p lia n t Un d e r 2002/95/EC With o u t Me rc u ry The details provided in this appendix are to ensure that the product is compliant with the Peoples Republic of China (China) RoHS standards. The table below acknowledges the presences of small quantities of certain materials in the product, and is applicable to China RoHS only.
~~PAGE 146~~
TANK-720 Em b e d d e d S ys te m P a rt Na m e To xic o r Ha za rd o u s S u b s ta n c e s a n d Ele m e n ts Le a d Me rc u ry Ca d m iu m He xa va le n t P o lyb ro m in a te d P o lyb ro m in a te d (P b ) (Hg ) (Cd ) Ch ro m iu m Bip h e n yls Dip h e n yl (CR(VI)) (P BB) Eth e rs (P BDE) Ho u s in g X O O O O X Dis p la y X O O O O X P rin te d Circ u it X O O O O X X O O O O O X O O O O X Fa n As s e m b ly X O O O O X P owe r S u p p ly X O
~~PAGE 147~~
TANK-720 Em b e d d e d S ys te m 此附件旨在确保本产品符合中国 RoHS 标准。以下表格标示此产品中某有毒物质的含量符合中国 RoHS 标准规定的限量要求。本产品上会附有”环境友好使用期限”的标签，此期限是估算这些物质”不会有泄漏或突变”的年限。本产品可能包含有较短的环境友好使用期限的可替换元件，像是电池或灯管，这些元件将会单独标示出来。部件名称有毒有害物质或元素铅汞镉六价铬多溴联苯多溴二苯 (P b ) (Hg ) (Cd ) (CR(VI)) (P BB) 醚 (P BDE) 壳体 X O O O O X 显示 X O O O O X 印刷电路板 X O O O O X 金属螺帽 X O O O O O 电缆组装 X O O O O X 风扇组装 X O O O O X 电力供应组装 X O O O O X 电池 O O O O O O O: 表示该有毒有害物质在该部件所有物质材料中的含量均在 SJ/T113