Manual

ManualsBrandsIEI Integration ManualsHardwareWAFER-CV-D25501_N26001

WAFER-CV-D25501/N26001 3.5" Motherboard

Page i

IEI Technology Corp.

User Manual

3.5" SBC with Intel® Atom™ D2550/N2600 Processor,

DDR3, VGA/Dual LVDS, Dual PCIe GbE, USB 2.0,

PCIe Mini, SATA 3Gb/s, Audio and RoHS

MODEL:

WAFER-CV-D25501/N26001

Rev. 1.03 – 11 December, 2012

Summary of content (181 pages)

PAGE 1
WAFER-CV-D25501/N26001 3.5" Motherboard 1 IEI Technology Corp. MODEL: WAFER-CV-D25501/N26001 3.5" SBC with Intel® Atom™ D2550/N2600 Processor, DDR3, VGA/Dual LVDS, Dual PCIe GbE, USB 2.0, PCIe Mini, SATA 3Gb/s, Audio and RoHS User Manual Page i Rev. 1.
PAGE 2
WAFER-CV-D25501/N26001 3.5" Motherboard Revision Date Version Changes 11 December, 2012 1.03 Added CN6 connector information 23 November, 2012 1.02 Updated the note for the Intel® GMA driver limitation 13 August, 2012 1.01 Added a note for the Intel® GMA driver limitation 26 June, 20 1.
PAGE 3
WAFER-CV-D25501/N26001 3.5" Motherboard Copyright COPYRIGHT NOTICE The information in this document is subject to change without prior notice in order to improve reliability, design and function and does not represent a commitment on the part of the manufacturer. In no event will the manufacturer be liable for direct, indirect, special, incidental, or consequential damages arising out of the use or inability to use the product or documentation, even if advised of the possibility of such damages.
PAGE 4
WAFER-CV-D25501/N26001 3.5" Motherboard Table of Contents 1 INTRODUCTION.......................................................................................................... 1 1.1 INTRODUCTION........................................................................................................... 2 1.2 MODEL VARIATIONS ................................................................................................... 2 1.3 CONNECTORS ..................................................................
PAGE 5
WAFER-CV-D25501/N26001 3.5" Motherboard 3.2.12 PCIe Mini Card Slots..................................................................................... 26 3.2.13 Power & HDD LED Connector..................................................................... 28 3.2.14 Power Button Connector................................................................................ 29 3.2.15 Reset Button Connector ................................................................................. 30 3.2.
PAGE 6
WAFER-CV-D25501/N26001 3.5" Motherboard 4.7 EXTERNAL PERIPHERAL INTERFACE CONNECTION ................................................... 58 4.7.1 LAN Connection............................................................................................... 58 4.7.2 Serial Device Connection ................................................................................ 59 4.7.3 USB Connection (Dual Connector) ................................................................. 60 4.7.4 VGA Monitor Connection ..
PAGE 7
WAFER-CV-D25501/N26001 3.5" Motherboard 6.1 AVAILABLE SOFTWARE DRIVERS .............................................................................. 93 6.2 STARTING THE DRIVER PROGRAM ............................................................................ 93 6.3 CHIPSET DRIVER INSTALLATION ............................................................................... 95 6.4 GRAPHICS DRIVER INSTALLATION ............................................................................ 99 6.
PAGE 8
WAFER-CV-D25501/N26001 3.5" Motherboard C TERMINOLOGY ..................................................................................................... 153 D DIGITAL I/O INTERFACE..................................................................................... 157 D.1 INTRODUCTION ...................................................................................................... 158 D.2 DIO CONNECTOR PINOUTS ...................................................................................
PAGE 9
WAFER-CV-D25501/N26001 3.5" Motherboard List of Figures Figure 1-1: WAFER-CV-D25501/N26001 .......................................................................................2 Figure 1-2: Connectors ..................................................................................................................3 Figure 1-3: WAFER-CV-D25501/N26001 Dimensions (mm) ........................................................4 Figure 1-4: External Interface Panel Dimensions (mm) ..............................
PAGE 10
WAFER-CV-D25501/N26001 3.5" Motherboard Figure 4-2: AT/ATX Power Selection Jumper Location ............................................................43 Figure 4-3: Clear CMOS Jumper Location .................................................................................44 Figure 4-4: LVDS1 Voltage Selection Jumper Location ...........................................................45 Figure 4-5: LVDS2 Voltage Selection Jumper Location ...........................................................
PAGE 11
WAFER-CV-D25501/N26001 3.5" Motherboard Figure 6-14: LAN Driver Welcome Screen .............................................................................. 103 Figure 6-15: LAN Driver Installation ........................................................................................ 104 Figure 6-16: LAN Driver Installation Complete....................................................................... 104 Figure 6-17: Audio Driver Installation File Extraction.............................................
PAGE 12
WAFER-CV-D25501/N26001 3.5" Motherboard Figure B-29: Press any key to continue .................................................................................. 132 Figure B-30: IEI Feature ............................................................................................................ 133 Figure B-31: Partitions for Linux.............................................................................................. 134 Figure B-32: System Configuration for Linux.................................
PAGE 13
WAFER-CV-D25501/N26001 3.5" Motherboard List of Tables Table 1-1: WAFER-CV-D25501/N26001 Model Variations ...........................................................2 Table 1-2: WAFER-CV-D25501/N26001 Specifications ...............................................................8 Table 2-1: Packing List.................................................................................................................12 Table 2-2: Optional Items..................................................................
PAGE 14
WAFER-CV-D25501/N26001 3.5" Motherboard Table 4-1: Jumpers .......................................................................................................................42 Table 4-2: AT/ATX Power Selection Jumper Settings...............................................................43 Table 4-3: Clear CMOS Jumper Settings....................................................................................43 Table 4-4: LVDS1 Voltage Selection Jumper Settings..........................................
PAGE 15
WAFER-CV-D25501/N26001 3.5" Motherboard BIOS Menus BIOS Menu 1: Main .......................................................................................................................67 BIOS Menu 2: Advanced ..............................................................................................................68 BIOS Menu 3: ACPI Settings .......................................................................................................69 BIOS Menu 4: RTC Wake Settings .....................
PAGE 16
WAFER-CV-D25501/N26001 3.
PAGE 17
WAFER-CV-D25501/N26001 3.5" Motherboard 1.1 Introduction Figure 1-1: WAFER-CV-D25501/N26001 The WAFER-CV-D25501/N26001 3.5” motherboard is an Intel® Atom™ D2550/N2600 processor platform that supports one 1066 MHz or 800 MHz DDR3 SO-DIMM memory. The WAFER-CV-D25501/N26001 supports VGA display output and comes with two LVDS connectors supporting 24-bit or 18-bit LVDS screens.
PAGE 18
WAFER-CV-D25501/N26001 3.5" Motherboard 1.3 Connectors The connectors on the WAFER-CV-D25501/N26001 are shown in the figure below.
PAGE 19
WAFER-CV-D25501/N26001 3.5" Motherboard 1.4 Dimensions The main dimensions of the WAFER-CV-D25501/N26001 are shown in the diagram below.
PAGE 20
WAFER-CV-D25501/N26001 3.5" Motherboard .
PAGE 21
WAFER-CV-D25501/N26001 3.5" Motherboard 1.5 Data Flow Figure 1-5 shows the data flow between the system chipset, the CPU and other 6 components installed on the motherboard.
PAGE 22
WAFER-CV-D25501/N26001 3.5" Motherboard 1.6 Technical Specifications The WAFER-CV-D25501/N26001 technical specifications are listed below. Specification/Model WAFER-CV-D25501 Form Factor 3.5” System CPU Intel® Atom™ D2550 1.86 GHz System Chipset Intel® NM10 Memory Graphics Engine WAFER-CV-N26001 Intel® Atom™ N2600 1.6 GHz One 1066 MHz DDR3/DDR3L (1.35V) One 800 MHz DDR3/DDR3L (1.
PAGE 23
WAFER-CV-D25501/N26001 3.5" Motherboard Specification/Model Fan WAFER-CV-D25501 WAFER-CV-N26001 One 3-pin CPU fan connector One 3-pin system fan connector Keyboard/mouse One internal pin-header connector SATA Two SATA 3Gb/s ports with 5V power Six USB 2.0/1.1 devices supported: USB Two by external connectors Four by on-board pin headers 12 V only Power Supply AT and ATX support One internal 4-pin (2x2) power connector 12V @ 1.53 A (1.86 GHz Intel® 12V @ 1.15 A (1.
PAGE 24
WAFER-CV-D25501/N26001 3.
PAGE 25
WAFER-CV-D25501/N26001 3.5" Motherboard 2.1 Anti-static Precautions WARNING! Static electricity can destroy certain electronics. Make sure to follow the ESD precautions to prevent damage to the product, and injury to the user. Make sure to adhere to the following guidelines: Wear an anti-static wristband: Wearing an anti-static wristband can prevent electrostatic discharge. Self-grounding: Touch a grounded conductor every few minutes to discharge any excess static buildup.
PAGE 26
WAFER-CV-D25501/N26001 3.5" Motherboard 2.3 Packing List NOTE: If any of the components listed in the checklist below are missing, do not proceed with the installation. Contact the IEI reseller or vendor the WAFER-CV-D25501/N26001 was purchased from or contact an IEI sales representative directly by sending an email to sales@iei.com.tw.
PAGE 27
WAFER-CV-D25501/N26001 3.5" Motherboard Quantity Item and Part Number 1 Mini jumper pack 1 One Key Recovery CD 1 Utility CD 1 Quick Installation Guide Image Table 2-1: Packing List 2.
PAGE 28
WAFER-CV-D25501/N26001 3.
PAGE 29
WAFER-CV-D25501/N26001 3.5" Motherboard 3.1 Peripheral Interface Connectors This chapter details all the jumpers and connectors. 3.1.1 WAFER-CV-D25501/N26001 Layout The figure below shows all the connectors and jumpers.
PAGE 30
WAFER-CV-D25501/N26001 3.5" Motherboard 3.1.2 Peripheral Interface Connectors The table below lists all the connectors on the board.
PAGE 31
WAFER-CV-D25501/N26001 3.5" Motherboard 3.1.3 External Interface Panel Connectors The table below lists the connectors on the external I/O panel. Connector Type Label Dual USB port Dual USB port USB1 Ethernet connectors RJ-45 LAN1, LAN2 RS-232 serial port connector Male DB-9 COM1 VGA connector 15-pin female VGA1 Table 3-2: Rear Panel Connectors 3.2 Internal Peripheral Connectors The section describes all of the connectors on the WAFER-CV-D25501/N26001. 3.2.
PAGE 32
WAFER-CV-D25501/N26001 3.5" Motherboard Pin No. Description 1 +5V 2 Ground Table 3-3: 5 V SATA Power Connector Pinouts 3.2.2 12 V Power Connector CN Label: CN3 CN Type: 4-pin Molex power connector CN Location: See Figure 3-3 CN Pinouts: See Table 3-4 The ATX power connector connects to an ATX power supply. Figure 3-3: 12 V Power Connector Location Pin Description 1 GND 2 GND 3 +12V 4 +12V Table 3-4: 12 V Power Connector Pinouts 3.2.
PAGE 33
WAFER-CV-D25501/N26001 3.5" Motherboard The 10-pin audio connector is connected to external audio devices including speakers and microphones for the input and output of audio signals to and from the system. Figure 3-4: Audio Connector Location Pin Description Pin Description 1 Line-out_R 2 Line-in_R 3 AUD_GND 4 AUD_GND 5 Line-out _L 6 Line-in _L 7 AUD_GND 8 AUD_GND 9 MIC1_R 10 MIC1_L Table 3-5: Audio Connector Pinouts 3.2.
PAGE 34
WAFER-CV-D25501/N26001 3.5" Motherboard Figure 3-5: Backlight Inverter Connector Locations Pin Description 1 LCD_BKLTCTL 2 GROUND 3 +12V 4 GROUND 5 LCD_BKLEN Table 3-6: Backlight Inverter Connector Pinouts 3.2.5 Battery Connector CAUTION: Risk of explosion if battery is replaced by an incorrect type. Only certified engineers should replace the on-board battery. Dispose of used batteries according to instructions and local regulations.
PAGE 35
WAFER-CV-D25501/N26001 3.5" Motherboard CN Location: See Figure 3-6 CN Pinouts: See Table 3-7 This is connected to the system battery. The battery provides power to the system clock to retain the time when power is turned off. Figure 3-6: Battery Connector Location Pin Description 1 Battery+ 2 GND Table 3-7: Battery Connector Pinouts 3.2.
PAGE 36
WAFER-CV-D25501/N26001 3.5" Motherboard Figure 3-7: Digital I/O Connector Location Pin Description Pin Description 1 GND 2 VCC 3 Output 3 4 Output 2 5 Output 1 6 Output 0 7 Input 3 8 Input 2 9 Input 1 10 Input 0 Table 3-8: Digital I/O Connector Pinouts 3.2.7 Fan Connectors CN Label: CPU_FAN1, SYS_FAN1 CN Type: 3-pin wafer CN Location: See Figure 3-8 CN Pinouts: See Table 3-9 The fan connectors attach to the CPU/system cooling fans.
PAGE 37
WAFER-CV-D25501/N26001 3.5" Motherboard Figure 3-8: Fan Connector Locations PIN NO. DESCRIPTION 1 GND 2 +12 V 3 Fan Speed Detect Table 3-9: Fan Connector Pinouts 3.2.8 Keyboard/Mouse Connector CN Label: KB_MS1 CN Type: 6-pin wafer CN Location: See Figure 3-9 CN Pinouts: See Table 3-10 The keyboard and mouse connector can be connected to a standard PS/2 cable or PS/2 Y-cable to add keyboard and mouse functionality to the system.
PAGE 38
WAFER-CV-D25501/N26001 3.5" Motherboard Figure 3-9: Keyboard/Mouse Connector Location Pin Description 1 +5 V KB DATA 2 MS DATA 3 MS CLK 4 KB DATA 5 KB CLK 6 GROUND Table 3-10: Keyboard/Mouse Connector Pinouts 3.2.9 LVDS1 Connector CN Label: LVDS1 CN Type: 20-pin crimp CN Location: See Figure 3-10 CN Pinouts: See Table 3-11 The 20-pin LVDS LCD connector can be connected to an 18-bit/24-bit single-channel LVDS panel.
PAGE 39
WAFER-CV-D25501/N26001 3.5" Motherboard Figure 3-10: LVDS1 Connector Location Pin Description Pin Description 1 GND 2 GND 3 LVDS_DATA0 4 LVDS_DATA0# 5 LVDS_DATA1 6 LVDS_DATA1# 7 LVDS_DATA2 8 LVDS_DATA2# 9 LVDS_CLK 10 LVDS_CLK# 11 LVDS_DATA3 12 LVDS_DATA3# 13 GND 14 GND 15 LDDC_DATA 16 LDDC_CLK 17 VCC_LCD 18 VCC_LCD 19 VCC_LCD 20 VCC_LCD Table 3-11: LVDS1 Connector Pinouts 3.2.
PAGE 40
WAFER-CV-D25501/N26001 3.
PAGE 41
WAFER-CV-D25501/N26001 3.5" Motherboard 3.2.11 LVDS2 Backlight Control Connector CN Label: CN6 CN Type: 6-pin wafer CN Location: See Figure 3-12 CN Pinouts: See Table 3-13 This connector allows control of the LVDS2 panel backlight. Figure 3-12: LVDS2 Backlight Control Connector Location Function Panel power button Panel brightness + Panel brightness - Pin Description 1 PWRDN 2 GND 3 BLUP 4 GND 5 BLDN 6 GND Table 3-13: LVDS2 Backlight Control Connector Pinouts 3.2.
PAGE 42
WAFER-CV-D25501/N26001 3.5" Motherboard NOTE: The M_PCIE2 slot supports mSATA devices. Figure 3-13: PCIe Mini Card Slot Locations Pin Description Pin Description 1 PCIE_WAKE# 2 VCC3 3 N/C 4 GND 5 N/C 6 1.5V 7 N/C 8 N/C 9 GND 10 N/C 11 PCIE_CLK# 12 N/C 13 PCIE_CLK 14 N/C 15 GND 16 N/C 17 N/C 18 GND 19 N/C 20 N/C 21 GND 22 PCIRST# 23 PCIE_RXN 24 VCC3 25 PCIE_RXP 26 GND 27 GND 28 1.
PAGE 43
WAFER-CV-D25501/N26001 3.5" Motherboard Pin Description Pin Description 37 GND 38 USBD+ 39 VCC3 40 GND 41 VCC3 42 N/C 43 GND 44 N/C 45 N/C 46 N/C 47 N/C 48 1.5V 49 N/C 50 GND 51 N/C 52 VCC3 Table 3-14: PCIe Mini Card Slot Pinouts 3.2.
PAGE 44
WAFER-CV-D25501/N26001 3.5" Motherboard Pin Description 1 +5V 2 GND 3 Power LED+ 4 Power LED- 5 HDD LED+ 6 HDD LED- Table 3-15: Power & HDD LED Connector Pinouts 3.2.14 Power Button Connector CN Label: PWR_BTN1 CN Type: 2-pin wafer CN Location: See Figure 3-15 CN Pinouts: See Table 3-16 The power button connector is connected to a power switch on the system chassis to enable users to turn the system on and off.
PAGE 45
WAFER-CV-D25501/N26001 3.5" Motherboard 3.2.15 Reset Button Connector CN Label: RST_BTN1 CN Type: 2-pin wafer CN Location: See Figure 3-16 CN Pinouts: See Table 3-17 The reset button connector is connected to a reset switch on the system chassis to enable users to reboot the system when the system is turned on. Figure 3-16: Reset Button Connector Location Pin Description 1 RESET+ 2 RESET- Table 3-17: Reset Button Connector Pinouts 3.2.
PAGE 46
WAFER-CV-D25501/N26001 3.5" Motherboard Figure 3-17: RS-232 Serial Port Connector Locations Pin Description Pin Description 1 DCD 2 DSR 3 RXD 4 RTS 5 TXD 6 CTS 7 DTR 8 RI 9 GND 10 GND Table 3-18: RS-232 Serial Port Connector Pinouts 3.2.17 RS-422/485 Serial Port Connector CN Label: COM4 CN Type: 4-pin wafer CN Location: See Figure 3-18 CN Pinouts: See Table 3-19 NOTE: These pins are shared with those on the main serial port.
PAGE 47
WAFER-CV-D25501/N26001 3.5" Motherboard Figure 3-18: RS-422/485 Connector Location Pin Description Pin Description 1 RXD422- 3 TXD422+/TXD485+ 2 RXD422+ 4 TXD422-/TXD485- Table 3-19: RS-422/485Connector Pinouts 3.2.18 SATA Drive Connectors CN Label: SATA1, SATA2 CN Type: 7-pin SATA drive connector CN Location: See Figure 3-19 CN Pinouts: See Table 3-20 The SATA drive connectors can be connected to SATA drives and support up to 3Gb/s data transfer rate.
PAGE 48
WAFER-CV-D25501/N26001 3.5" Motherboard Pin Description 1 GND 2 TX+ 3 TX- 4 GND 5 RX- 6 RX+ 7 GND Table 3-20: SATA Drive Connector Pinouts 3.2.19 USB Connectors CN Label: USB2, USB3 CN Type: 8-pin header CN Location: See Figure 3-20 CN Pinouts: See Table 3-21 Each USB connector provides connectivity to two USB 1.1/2.0 ports.
PAGE 49
WAFER-CV-D25501/N26001 3.5" Motherboard Pin Description Pin Description 7 GND 8 USB_VCC Table 3-21: USB Connector Pinouts 3.3 External Peripheral Interface Connector Panel The figure below shows the external peripheral interface connector (EPIC) panel. The EPIC panel consists of the following: Figure 3-21: External Peripheral Interface Connector 3.3.
PAGE 50
WAFER-CV-D25501/N26001 3.5" Motherboard Figure 3-22: RJ-45 Ethernet Connector LED Description LED Description A on: linked B off: 10 Mb/s blinking: data is being sent/received green: 100 Mb/s orange: 1000 Mb/s Table 3-23: RJ-45 Ethernet Connector LEDs 3.3.2 Serial Port Connector (COM1) CN Label: COM1 CN Type: Male DB-9 connector CN Location: See Figure 3-21 CN Pinouts: See Table 3-24 and Figure 3-23 The serial port connects to a RS-232 serial communications device.
PAGE 51
WAFER-CV-D25501/N26001 3.5" Motherboard Figure 3-23: COM1 Pinout Locations 3.3.3 USB Connectors CN Label: USB1 CN Type: Dual USB port CN Location: See Figure 3-21 CN Pinouts: See Table 3-25 The ports connect to both USB 2.0 and USB 1.1 devices. Pin Description Pin Description 1 USB_VCC 2 USB_VCC 3 DATA- 4 DATA- 5 DATA+ 6 DATA+ 7 GND 8 GND Table 3-25: USB Port Pinouts 3.3.
PAGE 52
WAFER-CV-D25501/N26001 3.5" Motherboard Pin Description Pin Description 1 RED 2 GREEN 3 BLUE 4 NC 5 GND 6 GND 7 GND 8 GND 9 VGAVCC 10 GND 11 NC 12 DDCDAT 13 HSYNC 14 VSYNC 15 DDCCLK Table 3-26: VGA Connector Pinouts Figure 3-24: VGA Connector NOTE: Due to Intel® GMA driver limitation, the monitor connected to the VGA connector may become extended desktop or not have signal to it after restarting from the graphics driver installation.
PAGE 53
WAFER-CV-D25501/N26001 3.
PAGE 54
WAFER-CV-D25501/N26001 3.5" Motherboard 4.1 Anti-static Precautions WARNING: Failure to take ESD precautions during the installation of the WAFER-CV-D25501/N26001 may result in permanent damage to the WAFER-CV-D25501/N26001 and severe injury to the user. Electrostatic discharge (ESD) can cause serious damage to electronic components, including the WAFER-CV-D25501/N26001. Dry climates are especially susceptible to ESD.
PAGE 55
WAFER-CV-D25501/N26001 3.5" Motherboard WARNING: The installation instructions described in this manual should be carefully followed in order to prevent damage to the components and injury to the user. Before and during the installation please DO the following: Read the user manual: o The user manual provides a complete description of the WAFER-CV-D25501/N26001 installation instructions and configuration options.
PAGE 56
WAFER-CV-D25501/N26001 3.5" Motherboard 4.3 SO-DIMM Installation WARNING: Using incorrectly specified SO-DIMM may cause permanent damage to the WAFER-CV-D25501/N26001. Please make sure the purchased SO-DIMM complies with the memory specifications of the WAFER-CV-D25501/N26001. SO-DIMM specifications compliant with the WAFER-CV-D25501/N26001 are listed in Chapter 1. To install a SO-DIMM into a SO-DIMM socket, please follow the steps below and refer to Figure 4-1.
PAGE 57
WAFER-CV-D25501/N26001 3.5" Motherboard Step 5: Secure the SO-DIMM. Release the arms on the SO-DIMM socket. They clip into place and secure the SO-DIMM in the socket.Step 0: 4.4 Jumper Settings NOTE: A jumper is a metal bridge used to close an electrical circuit. It consists of two or three metal pins and a small metal clip (often protected by a plastic cover) that slides over the pins to connect them.
PAGE 58
WAFER-CV-D25501/N26001 3.5" Motherboard The AT/ATX power selection jumper specifies the system power mode as AT or ATX. Setting Description Short 1-2 Use ATX power (Default) Off Use AT power Table 4-2: AT/ATX Power Selection Jumper Settings Figure 4-2: AT/ATX Power Selection Jumper Location 4.4.
PAGE 59
WAFER-CV-D25501/N26001 3.5" Motherboard Figure 4-3: Clear CMOS Jumper Location 4.4.3 LVDS1 Voltage Selection WARNING: Permanent damage to the screen and WAFER-CV-D25501/N26001 may occur if the wrong voltage is selected with this jumper. Please refer to the user guide that came with the monitor to select the correct voltage. Jumper Label: JP4 Jumper Type: 3-pin header Jumper Settings: See Table 4-4 Jumper Location: See Figure 4-4 Sets the voltage provided to the monitor by LVDS1.
PAGE 60
WAFER-CV-D25501/N26001 3.5" Motherboard Figure 4-4: LVDS1 Voltage Selection Jumper Location 4.4.4 LVDS2 Voltage Selection WARNING: Permanent damage to the screen and WAFER-CV-D25501/N26001 may occur if the wrong voltage is selected with this jumper. Please refer to the user guide that came with the monitor to select the correct voltage.
PAGE 61
WAFER-CV-D25501/N26001 3.5" Motherboard Figure 4-5: LVDS2 Voltage Selection Jumper Location 4.4.5 LVDS2 Panel Type Selection Jumper Jumper Label: SW1 Jumper Type: 4-pin switch Jumper Settings: See Table 4-6 Jumper Location: See Figure 4-6 Sets the panel type of the LVDS2 video channel. Pin No.
PAGE 62
WAFER-CV-D25501/N26001 3.5" Motherboard Pin No. 4321 EDID Resolution Color Depth Channel 1100 1680 x 1050 @ 60Hz 24-bit Dual 1101 1600 x 1200 @ 60Hz 24-bit Dual 1110 1920 x 1080 @ 60Hz 24-bit Dual 1111 1920 x 1200 @ 60Hz 24-bit Dual Table 4-6: LVDS2 Panel Resolution Figure 4-6: LVDS2 Panel Type Selection Switch Location 4.5 Chassis Installation 4.5.1 Airflow WARNING: Airflow is critical to the cooling of the CPU and other on-board components.
PAGE 63
WAFER-CV-D25501/N26001 3.5" Motherboard individual power supply unit, the cooling fan of a power supply can also help generate airflow through the board surface. NOTE: IEI has a wide range of chassis available. Please contact your WAFER-CV-D25501/N26001 representative at vendor, sales@iei.com.tw 3 reseller or visit or the an IEI IEI sales website (http://www.ieiworld.com.tw) to find out more about the available 3 chassis. 4.5.
PAGE 64
WAFER-CV-D25501/N26001 3.5" Motherboard Figure 4-7: Audio Kit Cable Connection Step 3: Connect the audio devices. Connect one speaker to the line-in audio jack, one speaker to the line-out audio jack and a microphone to the mic-in audio jack. 4.6.2 LVDS LCD Installation The WAFER-CV-D25501/N26001 can be connected to a TFT LCD screen through the LVDS crimp connectors on the board. To connect a TFT LCD to the WAFER-CV-D25501/N26001, please follow the steps below. Step 1: Locate the connector.
PAGE 65
WAFER-CV-D25501/N26001 3.5" Motherboard WARNING: The diagram below is merely for illustration. The configuration and connection of the cables from the TFT LCD screen being installed may be different. Please refer to the installation manual that came with the TFT LCD screen. Figure 4-8: LVDS Connector Step 3: Locate the backlight inverter connector. The locations of the backlight inverter connectors are shown in Chapter 3. Step 4: Connect backlight connector.
PAGE 66
WAFER-CV-D25501/N26001 3.5" Motherboard Figure 4-9: Backlight Inverter Connection 4.6.3 Full-size PCIe Mini Card Installation To install a full-size PCIe Mini card, please follow the steps below. Step 1: Locate the full-size PCIe Mini card slot. The location of the full-size PCIe Mini card slot is shown in Chapter 3. Step 2: Remove the retention screw. Remove the retention screw secured on the motherboard as shown in Figure 4-10.
PAGE 67
WAFER-CV-D25501/N26001 3.5" Motherboard Figure 4-10: Remove the Retention Screw for the Full-size PCIe Mini Card Step 3: Insert into the socket at an angle. Line up the notch on the card with the notch on the connector. Slide the PCIe Mini card into the socket at an angle of about 20º (Figure 4-11). Figure 4-11: Insert the Full-size PCIe Mini Card into the Socket at an Angle Step 4: Secure the full-size PCIe Mini card.
PAGE 68
WAFER-CV-D25501/N26001 3.5" Motherboard Figure 4-12: Secure the Full-size PCIe Mini Card 4.6.4 Half-size PCIe Mini Card Installation To install a half-size PCIe Mini card, please follow the steps below. Step 1: Locate the half-size PCIe Mini card slot. The location of the half-size PCIe Mini card slot is shown in Chapter 3. Step 2: Remove the retention screws. Remove the two retention screws secured on the motherboard as shown in Figure 4-13.
PAGE 69
WAFER-CV-D25501/N26001 3.5" Motherboard Step 3: Insert into the socket at an angle. Line up the notch on the card with the notch on the connector. Slide the PCIe Mini card into the socket at an angle of about 20º (Figure 4-14). Figure 4-14: Insert the Half-size PCIe Mini Card into the Socket at an Angle Step 4: Secure the half-size PCIe Mini card. Secure the half-size PCIe Mini card with the two retention screws previously removed (Figure 4-15). Figure 4-15: Secure the Half-size PCIe Mini Card 4.6.
PAGE 70
WAFER-CV-D25501/N26001 3.5" Motherboard Step 1: Locate the SATA connector and the SATA power connector. The locations of the connectors are shown in Chapter 3. Step 2: Insert the cable connector. Insert the cable connector into the on-board SATA drive connector and the SATA power connector. See Figure 4-16. Figure 4-16: SATA Drive Cable Connection Step 3: Connect the cable to the SATA disk. Connect the connector on the other end of the cable to the connector at the back of the SATA drive. See Figure 4-16.
PAGE 71
WAFER-CV-D25501/N26001 3.5" Motherboard Step 1: Locate the connector. The locations of the RS-232 connectors are shown in Chapter 3. Step 2: Insert the cable connector. Insert the connector into the serial port header. See Figure 4-17. A key on the front of the cable connector ensures the connector can only be installed in one direction. Figure 4-17: Single RS-232 Cable Installation Step 3: Secure the bracket.
PAGE 72
WAFER-CV-D25501/N26001 3.5" Motherboard Step 1: Locate the connector. The location of the keyboard/mouse Y-cable connector is shown in Chapter 3. Step 2: Align the connectors. Correctly align pin 1 on the cable connector with pin 1 on the WAFER-CV-D25501/N26001 keyboard/mouse connector. See Figure 4-18. Step 3: Insert the cable connectors. Once the cable connector is properly aligned with the keyboard/mouse connector on the WAFER-CV-D25501/N26001, connect the cable connector to the on-board connector.
PAGE 73
WAFER-CV-D25501/N26001 3.5" Motherboard PS/2 connectors. The keyboard PS/2 connector and mouse PS/2 connector are both marked. Please make sure the keyboard and mouse are connected to the correct PS/2 connector. 4.7 External Peripheral Interface Connection This section describes connecting devices to the external connectors on the WAFER-CV-D25501/N26001. 4.7.1 LAN Connection The RJ-45 connector enables connection to an external network.
PAGE 74
WAFER-CV-D25501/N26001 3.5" Motherboard Step 3: Insert the LAN cable RJ-45 connector. Once aligned, gently insert the LAN cable RJ-45 connector into the on-board RJ-45 connector. 4.7.2 Serial Device Connection The WAFER-CV-D25501/N26001 has a single male DB-9 connector on the external peripheral interface panel for a serial device. Follow the steps below to connect a serial device to the WAFER-CV-D25501/N26001. Step 1: Locate the DB-9 connector. The location of the DB-9 connector is shown in Chapter 3.
PAGE 75
WAFER-CV-D25501/N26001 3.5" Motherboard 4.7.3 USB Connection (Dual Connector) The external USB Series "A" receptacle connectors provide easier and quicker access to external USB devices. Follow the steps below to connect USB devices to the WAFER-CV-D25501/N26001. Step 1: Locate the USB Series "A" receptacle connectors. The locations of the USB Series "A" receptacle connectors are shown in Chapter 3. Step 2: Insert a USB Series "A" plug.
PAGE 76
WAFER-CV-D25501/N26001 3.5" Motherboard Step 1: Locate the female DB-15 connector. The location of the female DB-15 connector is shown in Chapter 3. Step 2: Align the VGA connector. Align the male DB-15 connector on the VGA screen cable with the female DB-15 connector on the external peripheral interface. Step 3: Insert the VGA connector. Once the connectors are properly aligned with the insert the male connector from the VGA screen into the female connector on the WAFER-CV-D25501/N26001. See Figure 4-22.
PAGE 77
WAFER-CV-D25501/N26001 3.5" Motherboard 4.8 Heat Sink Enclosure WARNING: Never run the WAFER-CV-D25501/N26001 without the heat sink secured to the board. The heat sink ensures the system remains cool and does not need addition heat sinks to cool the system. WARNING: When running the WAFER-CV-D25501/N26001, do not put the WAFER-CV-D25501/N26001 directly on a surface that can not dissipate system heat, especially the wooden or plastic desk.
PAGE 78
WAFER-CV-D25501/N26001 3.
PAGE 79
WAFER-CV-D25501/N26001 3.
PAGE 80
WAFER-CV-D25501/N26001 3.5" Motherboard 5.1 Introduction The BIOS is programmed onto the BIOS chip. The BIOS setup program allows changes to certain system settings. This chapter outlines the options that can be changed. 5.1.1 Starting Setup The UEFI BIOS is activated when the computer is turned on. The setup program can be activated in one of two ways. 1. Press the DEL or F2 key as soon as the system is turned on or 2.
PAGE 81
WAFER-CV-D25501/N26001 3.5" Motherboard Key Function Esc key Main Menu – Quit and not save changes into CMOS Status Page Setup Menu and Option Page Setup Menu -Exit current page and return to Main Menu F1 General help, only for Status Page Setup Menu and Option Page Setup Menu F2 Load previous values F3 Load optimized defaults F4 Save changes and Exit BIOS Table 5-1: BIOS Navigation Keys 5.1.
PAGE 82
WAFER-CV-D25501/N26001 3.5" Motherboard 5.2 Main The Main BIOS menu (BIOS Menu 1) appears when the BIOS Setup program is entered. The Main menu gives an overview of the basic system information. Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc. Main Advanced Chipset Boot Security Save & Exit BIOS Information BIOS Vendor Core Version Compliancy Project Version Build Date and Time American Megatrends 4.6.5.3 0.16 UEFI 2.3; PI 1.2 B217AR10.ROM 03/14/2012 11:53:40 Set the Date.
PAGE 83
WAFER-CV-D25501/N26001 3.5" Motherboard System Time [xx:xx:xx] Use the System Time option to set the system time. Manually enter the hours, minutes and seconds. 5.3 Advanced Use the Advanced menu (BIOS Menu 2) to configure the CPU and peripheral devices through the following sub-menus: WARNING: Setting the wrong values in the sections below may cause the system to malfunction. Make sure that the settings made are compatible with the hardware.
PAGE 84
WAFER-CV-D25501/N26001 3.5" Motherboard Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc. Advanced ACPI Settings ACPI Sleep State [S1 (CPU Stop Clock)] Select the highest ACPI sleep state the system will enter when the SUSPEND button is pressed. ---------------------: Select Screen ↑ ↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit Version 2.14.1219. Copyright (C) 2011 American Megatrends, Inc.
PAGE 85
WAFER-CV-D25501/N26001 3.5" Motherboard Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc. Advanced Wake system with Fixed Time [Disabled] Enable or disable System wake on alarm event. When enabled, System will wake on the date::hr::min::sec specified ---------------------- : Select Screen ↑ ↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit Version 2.14.1219. Copyright (C) 2011 American Megatrends, Inc.
PAGE 86
WAFER-CV-D25501/N26001 3.5" Motherboard 5.3.3 CPU Configuration Use the CPU Configuration menu (BIOS Menu 5) to view detailed CPU specifications and configure the CPU. Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc. Advanced CPU Configuration Processor Type EMT64 Processor Speed System Bus Speed Ratio Status Actual Ratio System Bus Speed Processor Stepping Microcode Revision L1 Cache RAM L2 Cache RAM Processor Core Hyper-Threading Intel(R) Atom(TM) CPU D2700 @ 2.
PAGE 87
WAFER-CV-D25501/N26001 3.5" Motherboard Hyper-Threading [Enabled] Use the Hyper-Threading BIOS option to enable or disable the Intel Hyper-Threading Technology. Disables the Intel Hyper-Threading Technology. Disabled Enabled DEFAULT Enables the Intel Hyper-Threading Technology. 5.3.4 IDE Configuration Use the IDE Configuration menu (BIOS Menu 6) to change and/or set the configuration of the SATA devices installed in the system. Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc.
PAGE 88
WAFER-CV-D25501/N26001 3.5" Motherboard 5.3.5 USB Configuration Use the USB Configuration menu (BIOS Menu 7) to read USB configuration information and configure the USB settings. Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc. Advanced USB Configuration USB Devices: None Legacy USB Support [Enabled] Enables Legacy USB support. AUTO option disables legacy support if no USB devices are connected. DISABLE option will keep USB devices available only for EFI applications.
PAGE 89
WAFER-CV-D25501/N26001 3.5" Motherboard 5.3.6 F81866 Super IO Configuration Use the F81866 Super IO Configuration menu (BIOS Menu 8) to set or change the configurations for the serial ports. Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc.
PAGE 90
WAFER-CV-D25501/N26001 3.5" Motherboard 5.3.6.1.1 Serial Port 1 Configuration Serial Port [Enabled] Use the Serial Port option to enable or disable the serial port. Disable the serial port Disabled Enabled DEFAULT Enable the serial port Change Settings [Auto] Use the Change Settings option to change the serial port IO port address and interrupt address. Auto DEFAULT The serial port IO port address and interrupt address are automatically detected.
PAGE 91
WAFER-CV-D25501/N26001 3.5" Motherboard Change Settings [Auto] Use the Change Settings option to change the serial port IO port address and interrupt address. Auto DEFAULT The serial port IO port address and interrupt address are automatically detected.
PAGE 92
WAFER-CV-D25501/N26001 3.
PAGE 93
WAFER-CV-D25501/N26001 3.
PAGE 94
WAFER-CV-D25501/N26001 3.5" Motherboard PC Health Status The following system parameters and values are shown. The system parameters that are monitored are: System Temperatures: o o CPU Temperature System Temperature Fan Speeds: o o CPU Fan Speed System Fan Speed Voltages: o o o o o o o o +VCC_CPU +VCC_GFX +V1.05S +1.5_DDR3 VSB5V +V3.3S VSB3V VBAT 5.3.7.1 Smart Fan Mode Configuration Use the Smart Fan Mode Configuration submenu (BIOS Menu 11) to configure fan temperature and speed settings.
PAGE 95
WAFER-CV-D25501/N26001 3.5" Motherboard Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc.
PAGE 96
WAFER-CV-D25501/N26001 3.5" Motherboard Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc. Advanced COM1 Console Redirection > Console Redirection Settings [Disabled] COM2 Console Redirection > Console Redirection Settings [Disabled] Console Redirection Enable or Disable --------------------: Select Screen ↑ ↓: Select Item COM3 Enter: Select Console Redirection [Disabled] +/-: Change Opt.
PAGE 97
WAFER-CV-D25501/N26001 3.5" Motherboard 9600 Sets the serial port transmission speed at 9600. 19200 Sets the serial port transmission speed at 19200. 38400 Sets the serial port transmission speed at 38400. 57600 Sets the serial port transmission speed at 57600. 115200 DEFAULT Sets the serial port transmission speed at 115200. Data Bits [8] Use the Data Bits option to specify the number of data bits. Sets the data bits at 7. 7 8 DEFAULT Sets the data bits at 8.
PAGE 98
WAFER-CV-D25501/N26001 3.5" Motherboard 1 DEFAULT Sets the number of stop bits at 1. Sets the number of stop bits at 2. 2 5.3.9 iEi Feature Use the iEi Feature menu (BIOS Menu 13) to configure One Key Recovery function. Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc. Advanced iEi Feature Auto Recovery Function [Disabled] Auto Recovery Function Reboot and recover system automatically within 10 min, when OS crashes.
PAGE 99
WAFER-CV-D25501/N26001 3.5" Motherboard 5.4 Chipset Use the Chipset menu (BIOS Menu 14) to access the Host Bridge and Southbridge configuration menus. WARNING! Setting the wrong values for the Chipset BIOS selections in the Chipset BIOS menu may cause the system to malfunction. Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc.
PAGE 100
WAFER-CV-D25501/N26001 3.5" Motherboard Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc. Chipset > Intel IGD Configuration Config Intel IGD Settings ******* Memory Information ******* Memory Frequency Total Memory DIMM#1 1067 MHz(DDR3) 1024 MB 1024 MB --------------------: Select Screen ↑ ↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit Version 2.14.1219. Copyright (C) 2011 American Megatrends, Inc.
PAGE 101
WAFER-CV-D25501/N26001 3.5" Motherboard IGFX - Boot Type [VBIOS Default] Use the IGFX - Boot Type option to select the display device used by the system when it boots. Configuration options are listed below. VBIOS Default DEFAULT CRT LVDS1 LVDS2 LVDS1 Panel Type [800x600 LVDS] Use the LVDS1 Panel Type option to select the type of flat panel connected to the system. Configuration options are listed below.
PAGE 102
WAFER-CV-D25501/N26001 3.5" Motherboard 5.4.2 South Bridge Configuration Use the South Bridge Configuration menu (BIOS Menu 17) to configure the Southbridge chipset. Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc. Chipset Auto Power Button Status [Disabled] Power Saving Function(ERP) Restore AC Power Loss [Disabled] [Last State] Enable to reduce power consumption in system off state. --------------------: Select Screen ↑ ↓: Select Item Enter: Select +/-: Change Opt.
PAGE 103
WAFER-CV-D25501/N26001 3.5" Motherboard 5.5 Boot Use the Boot menu (BIOS Menu 18) to configure system boot options. Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc.
PAGE 104
WAFER-CV-D25501/N26001 3.5" Motherboard Quiet Boot [Enabled] Use the Quiet Boot BIOS option to select the screen display when the system boots. Normal POST messages displayed Disabled Enabled DEFAULT OEM Logo displayed instead of POST messages Launch PXE OpROM [Disabled] Use the Launch PXE OpROM option to enable or disable boot option for legacy network devices. Disabled DEFAULT Ignore all PXE Option ROMs Load PXE Option ROMs.
PAGE 105
WAFER-CV-D25501/N26001 3.5" Motherboard 5.6 Security Use the Security menu (BIOS Menu 19) to set system and user passwords. Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc. Main Advanced Chipset Boot Security Save & Exit Password Description Set Setup Administrator Password If ONLY the Administrator’s password is set, then this only limits access to Setup and is only asked for when entering Setup.
PAGE 106
WAFER-CV-D25501/N26001 3.5" Motherboard Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc. Main Advanced Chipset Boot Security Save & Exit Save Changes and Reset Discard Changes and Reset Reset the system after saving the changes. Restore Defaults Save as User Defaults Restore User Defaults --------------------: Select Screen ↑ ↓: Select Item Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit Version 2.14.1219.
PAGE 107
WAFER-CV-D25501/N26001 3.
PAGE 108
WAFER-CV-D25501/N26001 3.5" Motherboard 6.1 Available Software Drivers NOTE: The content of the CD may vary throughout the life cycle of the product and is subject to change without prior notice. Visit the IEI website or contact technical support for the latest updates. The following drivers can be installed on the system: Chipset Graphics LAN Audio Installation instructions are given below. 6.2 Starting the Driver Program To access the driver installation programs, please do the following.
PAGE 109
WAFER-CV-D25501/N26001 3.5" Motherboard Figure 6-1: Start Up Screen Step 3: Click WAFER-CV-D25501/N26001. Step 4: The list of drivers in Figure 6-2 appears.
PAGE 110
WAFER-CV-D25501/N26001 3.5" Motherboard 6.3 Chipset Driver Installation To install the chipset driver, please do the following. Step 1: Access the driver list. (See Section 6.2) Step 2: Click “1-Chipset”. Step 3: Go to the 32-bit or 64-bit folder that corresponds to your OS version. Step 4: Open the Intel Chipset Software Installation Utility folder. Step 5: Double click the infinst_autol icon. Step 6: The setup files are extracted as shown in Figure 6-3.
PAGE 111
WAFER-CV-D25501/N26001 3.5" Motherboard Figure 6-4: Chipset Driver Welcome Screen Step 8: Click Next to continue. Step 9: The license agreement in Figure 6-5 appears. Step 10: Read the License Agreement. Step 11: Click Yes to continue.
PAGE 112
WAFER-CV-D25501/N26001 3.5" Motherboard Figure 6-5: Chipset Driver License Agreement Step 12: The Read Me file in Figure 6-6 appears. Step 13: Click Next to continue.
PAGE 113
WAFER-CV-D25501/N26001 3.5" Motherboard Step 14: Setup Operations are performed as shown in Figure 6-7. Figure 6-7: Chipset Driver Setup Operations Step 15: Once the Setup Operations are complete, click Next to continue. Step 16: The Finish screen appears. Step 17: Select “Yes, I want to restart the computer now” and click the Finish icon. See Figure 6-8.
PAGE 114
WAFER-CV-D25501/N26001 3.5" Motherboard Figure 6-8: Chipset Driver Installation Finish Screen 6.4 Graphics Driver Installation NOTE: Due to Intel® GMA driver limitation, the monitor connected to the VGA connector may become extended desktop or not have signal to it after restarting from the graphics driver installation. To work out this limitation, press the Ctrl+Alt+F1 hotkey to switch the primary display to CRT mode. To install the graphics driver, please do the following.
PAGE 115
WAFER-CV-D25501/N26001 3.5" Motherboard Step 5: The Welcome Screen in Figure 6-9 appears. Figure 6-9: Graphics Driver Welcome Screen Step 6: Click Next to continue. Step 7: The license agreement in Figure 6-10 appears. Step 8: Read the License Agreement. Step 9: Click Yes to continue.
PAGE 116
WAFER-CV-D25501/N26001 3.5" Motherboard Figure 6-10: Graphics Driver License Agreement Step 10: The Read Me file in Figure 6-11 appears. Step 11: Click Next to continue. Figure 6-11: Graphics Driver Read Me File Step 12: Setup Operations are performed as shown in Figure 6-12.
PAGE 117
WAFER-CV-D25501/N26001 3.5" Motherboard Figure 6-12: Graphics Driver Setup Operations Step 13: Once the Setup Operations are complete, click the Next icon to continue. Step 14: The Finish screen appears. Step 15: Select “Yes, I want to restart the computer now” and click the Finish icon. See Figure 6-13.
PAGE 118
WAFER-CV-D25501/N26001 3.5" Motherboard 6.5 LAN Driver Installation To install the LAN driver, please do the following. Step 1: Access the driver list shown in Figure 6-2. (See Section 6.2) Step 2: Click “3-LAN”. Step 3: Go to the Win7 > Install_Win7_7048_09162011 folder. Step 4: Double click the setup icon. Step 5: The Welcome screen in Figure 6-14 appears. Figure 6-14: LAN Driver Welcome Screen Step 6: Click Next to continue. Step 7: The Ready to Install screen in Figure 6-15 appears.
PAGE 119
WAFER-CV-D25501/N26001 3.5" Motherboard Figure 6-15: LAN Driver Installation Step 9: The program begins to install. Step 10: When the driver installation is complete, the screen in Figure 6-16 appears. Step 11: Click Finish to exit.
PAGE 120
WAFER-CV-D25501/N26001 3.5" Motherboard 6.6 Audio Driver Installation To install the Audio driver, please do the following. Step 1: Access the driver list. (See Section 6.2) Step 2: Click “4-Audio”. Step 3: Open the Win7 folder. Step 4: Double click the Vista_Win7_R263 icon. Step 5: The installation files are extracted as shown in Figure 6-17. Figure 6-17: Audio Driver Installation File Extraction Step 6: The Welcome screen in Figure 6-18 appears.
PAGE 121
WAFER-CV-D25501/N26001 3.5" Motherboard Figure 6-18: Audio Driver Welcome Screen Step 7: Click Next to continue. Step 8: The program begins to install. Step 9: The installation progress can be monitored in the progress bar shown in Figure 6-19. Figure 6-19: Audio Driver Installation Step 10: When the driver installation is complete, the screen in Figure 6-20 appears.
PAGE 122
WAFER-CV-D25501/N26001 3.5" Motherboard Figure 6-20: Audio Driver Installation Complete Step 11: Select “Yes, I want to restart my computer now” and click Finish. Step 12: The system reboots.
PAGE 123
WAFER-CV-D25501/N26001 3.
PAGE 124
WAFER-CV-D25501/N26001 3.5" Motherboard Below is a list of BIOS configuration options in the BIOS chapter. System Overview .................................................................................................................67 System Date [xx/xx/xx] ........................................................................................................67 System Time [xx:xx:xx] .......................................................................................................
PAGE 125
WAFER-CV-D25501/N26001 3.5" Motherboard Quiet Boot [Enabled] ...........................................................................................................89 Launch PXE OpROM [Disabled] .........................................................................................89 Option ROM Messages [Force BIOS].................................................................................89 UEFI Boot [Disabled] ....................................................................................
PAGE 126
WAFER-CV-D25501/N26001 3.
PAGE 127
WAFER-CV-D25501/N26001 3.5" Motherboard B.1 One Key Recovery Introduction The IEI one key recovery is an easy-to-use front end for the Norton Ghost system backup and recovery tool. This tool provides quick and easy shortcuts for creating a backup and reverting to that backup or reverting to the factory default settings.
PAGE 128
WAFER-CV-D25501/N26001 3.5" Motherboard After completing the five initial setup procedures as described above, users can access the recovery tool by pressing while booting up the system. The detailed information of each function is described in Section B.5. NOTE: The initial setup procedures for Linux system are described in Section B.3. 78 B.1.1 System Requirement NOTE: The recovery CD can only be used with IEI products.
PAGE 129
WAFER-CV-D25501/N26001 3.5" Motherboard partitions. Please take the following table as a reference when calculating the size of the partition. OS OS Image after Ghost Compression Ratio Windows® 7 7 GB 5 GB 70% Windows® XPE 776 MB 560 MB 70% Windows® CE 6.0 36 MB 28 MB 77% NOTE: Specialized tools are required to change the partition size if the operating system is already installed. B.1.
PAGE 130
WAFER-CV-D25501/N26001 3.5" Motherboard Linux o o o o o o o o o o o o o o Fedora Core 12 (Constantine) Fedora Core 11 (Leonidas) Fedora Core 10 (Cambridge) Fedora Core 8 (Werewolf) Fedora Core 7 (Moonshine) RedHat RHEL-5.4 RedHat 9 (Ghirke) Ubuntu 8.10 (Intrepid) Ubuntu 7.10 (Gutsy) Ubuntu 6.10 (Edgy) Debian 5.0 (Lenny) Debian 4.0 (Etch) SuSe 11.2 SuSe 10.3 NOTE: Installing unsupported OS versions may cause the recovery tool to fail. B.
PAGE 131
WAFER-CV-D25501/N26001 3.5" Motherboard The detailed descriptions are described in the following sections. NOTE: The setup procedures described below are for Microsoft Windows operating system users. For Linux, most of the setup procedures are the same except for several steps described in Section B.3. 78 B.2.1 Hardware and BIOS Setup Step 1: Make sure the system is powered off and unplugged. Step 2: Install a hard drive or SSD in the system. An unformatted and unpartitioned disk is recommended.
PAGE 132
WAFER-CV-D25501/N26001 3.5" Motherboard Step 2: Boot the system from recovery CD. When prompted, press any key to boot from the recovery CD. It will take a while to launch the recovery tool. Please be patient! Figure B-2: Launching the Recovery Tool Step 3: The recovery tool setup menu is shown as below. Figure B-3: Recovery Tool Setup Menu Step 4: Press <6> then .
PAGE 133
WAFER-CV-D25501/N26001 3.5" Motherboard Figure B-4: Command Prompt Step 5: The command prompt window appears. Type the following commands (marked in red) to create two partitions. One is for the OS installation; the other is for saving recovery files and images which will be an invisible partition.
PAGE 134
WAFER-CV-D25501/N26001 3.
PAGE 135
WAFER-CV-D25501/N26001 3.5" Motherboard NOTE: Use the following commands to check if the partitions were created successfully. Step 6: Press any key to exit the recovery tool and automatically reboot the system. Please continue to the following procedure: Build the Recovery Partition.Step0: B.2.3 Install Operating System, Drivers and Applications Install the operating system onto the unlabelled partition.
PAGE 136
WAFER-CV-D25501/N26001 3.5" Motherboard B.2.4 Build-up Recovery Partition Step 1: Put the recover CD in the optical drive. Step 2: Start the system. Step 3: Boot the system from the recovery CD. When prompted, press any key to boot from the recovery CD. It will take a while to launch the recovery tool. Please be patient! Figure B-6: Launching the Recovery Tool Step 4: When the recovery tool setup menu appears, press <2> then .
PAGE 137
WAFER-CV-D25501/N26001 3.5" Motherboard Step 5: The Symantec Ghost window appears and starts configuring the system to build a recovery partition. In this process the partition created for recovery files in Section B.2.2 is hidden and the recovery tool is saved in this partition. 78 Figure B-8: Building the Recovery Partition Step 6: After completing the system configuration, press any key in the following window to reboot the system. Figure B-9: Press Any Key to Continue Step 7: Eject the recovery CD.
PAGE 138
WAFER-CV-D25501/N26001 3.5" Motherboard B.2.5 Create Factory Default Image NOTE: Before creating the factory default image, please configure the system to a factory default environment, including driver and application installations. To create a factory default image, please follow the steps below. Step 1: Turn on the system. When the following screen displays (Figure B-10), press 78 the key to access the recovery tool.
PAGE 139
WAFER-CV-D25501/N26001 3.5" Motherboard Figure B-12: About Symantec Ghost Window Step 4: Use mouse to navigate to the option shown below (Figure B-13). 78 Figure B-13: Symantec Ghost Path Step 5: Select the local source drive (Drive 1) as shown in Figure B-14. Then click OK.
PAGE 140
WAFER-CV-D25501/N26001 3.5" Motherboard Figure B-14: Select a Local Source Drive Step 6: Select a source partition (Part 1) from basic drive as shown in Figure B-15. 78 Then click OK. Figure B-15: Select a Source Partition from Basic Drive Step 7: Select 1.2: [Recovery] NTFS drive and enter a file name called iei (Figure B-16). Click Save. The factory default image will then be saved in the 78 selected recovery drive and named IEI.GHO. WARNING: The file name of the factory default image must be iei.
PAGE 141
WAFER-CV-D25501/N26001 3.5" Motherboard Figure B-16: File Name to Copy Image to Step 8: When the Compress Image screen in Figure B-17 prompts, click High to make 78 the image file smaller.
PAGE 142
WAFER-CV-D25501/N26001 3.5" Motherboard Step 9: The Proceed with partition image creation window appears, click Yes to continue. Figure B-18: Image Creation Confirmation Step 10: The Symantec Ghost starts to create the factory default image (Figure B-19). 78 Figure B-19: Image Creation Complete Step 11: When the image creation completes, a screen prompts as shown in Figure B-20. 78 Click Continue and close the Ghost window to exit the program.
PAGE 143
WAFER-CV-D25501/N26001 3.5" Motherboard Step 12: The recovery tool main menu window is shown as below. Press any key to reboot the system. Step0: Figure B-21: Press Any Key to Continue B.3 Auto Recovery Setup Procedure The auto recovery function allows a system to automatically restore from the factory default image after encountering a Blue Screen of Death (BSoD) or a hang for around 10 minutes. To use the auto recovery function, follow the steps described in the following sections.
PAGE 144
WAFER-CV-D25501/N26001 3.5" Motherboard Step 1: Follow the steps described in Section B.2.1 ~ Section B.2.3 to setup BIOS, create partitions and install operating system. Step 2: Install the auto recovery utility into the system by double clicking the Utility/AUTORECOVERY-SETUP.exe in the One Key Recovery CD. This utility MUST be installed in the system, otherwise, the system will automatically restore from the factory default image every ten (10) minutes.
PAGE 145
WAFER-CV-D25501/N26001 3.5" Motherboard Step 4: Reboot the system from the recovery CD. When prompted, press any key to boot from the recovery CD. It will take a while to launch the recovery tool. Please be patient! Figure B-24: Launching the Recovery Tool Step 5: When the recovery tool setup menu appears, press <4> then . Figure B-25: Auto Recovery Environment for Windows Step 6: The Symantec Ghost window appears and starts configuring the system to build an auto recovery partition.
PAGE 146
WAFER-CV-D25501/N26001 3.5" Motherboard Figure B-26: Building the Auto Recovery Partition Step 7: After completing the system configuration, the following message prompts to confirm whether to create a factory default image. Type Y to have the system create a factory default image automatically. Type N within 6 seconds to skip this process (The default option is YES). It is suggested to choose YES for this option.
PAGE 147
WAFER-CV-D25501/N26001 3.5" Motherboard Step 8: The Symantec Ghost starts to create the factory default image (Figure B-28). Figure B-28: Image Creation Complete Step 9: After completing the system configuration, press any key in the following window to restart the system. Figure B-29: Press any key to continue Step 10: Eject the One Key Recovery CD and restart the system. Step 11: Press the key as soon as the system is turned on to enter the BIOS.
PAGE 148
WAFER-CV-D25501/N26001 3.5" Motherboard Main Advanced PCIPNP BIOS SETUP UTILITY Boot Security Chipset Exit iEi Feature ⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯ Auto Recovery Function [Enabled] Recover from PXE [Disabled] ↑ ↓ Enter F1 F10 ESC Select Screen Select Item Go to SubScreen General Help Save and Exit Exit v02.61 ©Copyright 1985-2006, American Megatrends, Inc. Figure B-30: IEI Feature Step 13: Save changes and restart the system.
PAGE 149
WAFER-CV-D25501/N26001 3.5" Motherboard Partition 1: / Partition 2: SWAP NOTE: Please reserve enough space for partition 3 for saving recovery images. Figure B-31: Partitions for Linux Step 3: Create a recovery partition. Insert the recovery CD into the optical disk drive. Follow Step 1 ~ Step 3 described in Section B.2.2. Then type the following 78 commands (marked in red) to create a partition for recovery images.
PAGE 150
WAFER-CV-D25501/N26001 3.5" Motherboard recovery partition. After completing the system configuration, press any key to reboot the system. Eject the recovery CD. Figure B-32: System Configuration for Linux Step 5: Access the recovery tool main menu by modifying the “menu.lst”. To first access the recovery tool main menu, the menu.lst must be modified. In Linux, enter Administrator (root). When prompt appears, type: cd /boot/grub vi menu.lst Figure B-33: Access menu.
PAGE 151
WAFER-CV-D25501/N26001 3.5" Motherboard Step 7: The recovery tool menu appears. (Figure B-34) 78 Figure B-34: Recovery Tool Menu Step 8: Create a factory default image. Follow Step 2 ~ Step 12 described in Section B.2.5 to create a factory default image. 78 B.5 Recovery Tool Functions After completing the initial setup procedures as described above, users can access the recovery tool by pressing while booting up the system. However, if the setup procedure in Section B.
PAGE 152
WAFER-CV-D25501/N26001 3.5" Motherboard Figure B-35: Recovery Tool Main Menu The recovery tool has several functions including: 1. Factory Restore: Restore the factory default image (iei.GHO) created in Section B.2.5. 78 2. Backup system: Create a system backup image (iei_user.GHO) which will be saved in the hidden partition. 3. Restore your last backup: Restore the last system backup image 4. Manual: Enter the Symantec Ghost window to configure manually. 5.
PAGE 153
WAFER-CV-D25501/N26001 3.5" Motherboard B.5.1 Factory Restore To restore the factory default image, please follow the steps below. Step 1: Type <1> and press in the main menu. Step 2: The Symantec Ghost window appears and starts to restore the factory default. A factory default image called iei.GHO is created in the hidden Recovery partition. Figure B-36: Restore Factory Default Step 3: The screen is shown in Figure B-37 appears when completed. Press any key to 78 reboot the system.
PAGE 154
WAFER-CV-D25501/N26001 3.5" Motherboard B.5.2 Backup System To backup the system, please follow the steps below. Step 1: Type <2> and press in the main menu. Step 2: The Symantec Ghost window appears and starts to backup the system. A backup image called iei_user.GHO is created in the hidden Recovery partition. Figure B-38: Backup System Step 3: The screen is shown in Figure B-39 appears when system backup is complete. 78 Press any key to reboot the system.
PAGE 155
WAFER-CV-D25501/N26001 3.5" Motherboard B.5.3 Restore Your Last Backup To restore the last system backup, please follow the steps below. Step 1: Type <3> and press in the main menu. Step 2: The Symantec Ghost window appears and starts to restore the last backup image (iei_user.GHO). Figure B-40: Restore Backup Step 3: The screen shown in Figure B-41 appears when backup recovery is complete. 78 Press any key to reboot the system.
PAGE 156
WAFER-CV-D25501/N26001 3.5" Motherboard B.5.4 Manual To restore the last system backup, please follow the steps below. Step 1: Type <4> and press in the main menu. Step 2: The Symantec Ghost window appears. Use the Ghost program to backup or recover the system manually. Figure B-42: Symantec Ghost Window Step 3: When backup or recovery is completed, press any key to reboot the system.
PAGE 157
WAFER-CV-D25501/N26001 3.5" Motherboard B.6 Restore Systems from a Linux Server through LAN The One Key Recovery allows a client system to automatically restore to a factory default image saved in a Linux system (the server) through LAN connectivity after encountering a Blue Screen of Death (BSoD) or a hang for around 10 minutes. To be able to use this function, the client system and the Linux system MUST reside in the same domain.
PAGE 158
WAFER-CV-D25501/N26001 3.5" Motherboard B.6.1 Configure DHCP Server Settings Step 1: Install the DHCP #yum install dhcp (CentOS, commands marked in red) #apt-get install dhcp3-server (Debian, commands marked in blue) Step 2: Confirm the operating system default settings: dhcpd.conf. CentOS Use the following command to show the DHCP server sample location: #vi /etc/dhcpd.conf The DHCP server sample location is shown as below: Use the following command to copy the DHCP server sample to etc/dhcpd.
PAGE 159
WAFER-CV-D25501/N26001 3.5" Motherboard filename “pxelinux.0”; B.6.2 Configure TFTP Settings Step 1: Install the tftp, httpd and syslinux. #yum install tftp-server httpd syslinux (CentOS) #apt-get install tftpd-hpa xinetd syslinux (Debian) Step 2: Enable the TFTP server by editing the “/etc/xinetd.d/tftp” file and make it use the remap file. The “-vvv” is optional but it could definitely help on getting more information while running the remap file. For example: CentOS #vi /etc/xinetd.
PAGE 160
WAFER-CV-D25501/N26001 3.5" Motherboard Debian Replace the TFTP settings from “inetd” to “xinetd” and annotate the “inetd” by adding “#”. #vi /etc/inetd.conf Modify: #tftp dgram udp wait root /usr/sbin....... (as shown below) #vi /etc/xinetd.d/tftp B.6.3 Configure One Key Recovery Server Settings Step 1: Copy the Utility/RECOVERYR10.TAR.BZ2 package from the One Key Recovery CD to the system (server side). Step 2: Extract the recovery package to /. #cp RecoveryR10.tar.bz2 / #cd / #tar –xvjf RecoveryR10.
PAGE 161
WAFER-CV-D25501/N26001 3.5" Motherboard B.6.4 Start the DHCP, TFTP and HTTP Start the DHCP, TFTP and HTTP. For example: CentOS #service xinetd restart #service httpd restart #service dhcpd restart Debian #/etc/init.d/xinetd reload #/etc/init.d/xinetd restart #/etc/init.d/dhcp3-server restart B.6.5 Create Shared Directory Step 1: Install the samba. #yum install samba Step 2: Create a shared directory for the factory default image. #mkdir /share #cd /share #mkdir /image #cp iei.
PAGE 162
WAFER-CV-D25501/N26001 3.5" Motherboard Modify: [image] comment = One Key Recovery path = /share/image browseable = yes writable = yes public = yes create mask = 0644 directory mask = 0755 Step 4: Edit “/etc/samba/smb.conf” for your environment. For example: Step 5: Modify the hostname #vi /etc/hostname Modify: RecoveryServer B.6.6 Setup a Client System for Auto Recovery Step 1: Disable the automatically restart function before creating the factory default image. Go to: My Computer Properties Advanced.
PAGE 163
WAFER-CV-D25501/N26001 3.5" Motherboard Figure B-43: Disable Automatically Restart Step 2: Configure the following BIOS options of the client system. Advanced → iEi Feature → Auto Recovery Function → Enabled Advanced → iEi Feature → Recover from PXE → Enabled Boot → Launch PXE OpROM → Enabled Step 3: Continue to configure the Boot Option Priorities BIOS option of the client system: Boot Option #1 remain the default setting to boot from the original OS. Boot Option #2 select the boot from LAN option.
PAGE 164
WAFER-CV-D25501/N26001 3.5" Motherboard MUST be installed in the system, otherwise, the system will automatically restore from the factory default image every ten (10) minutes. Step 6: Restart the client system from LAN. If the system encounters a Blue Screen of Death (BSoD) or a hang for around 10 minutes, it will automatically restore from the factory default image. The following screens will show when the system starts auto recovering.
PAGE 165
WAFER-CV-D25501/N26001 3.5" Motherboard NOTE: A firewall or a SELinux is not in use in the whole setup process described above. If there is a firewall or a SELinux protecting the system, modify the configuration information to accommodate them. B.7 Other Information B.7.1 Using AHCI Mode or ALi M5283 / VIA VT6421A Controller When the system uses AHCI mode or some specific SATA controllers such as ALi M5283 or VIA VT6421A, the SATA RAID/AHCI driver must be installed before using one key recovery.
PAGE 166
WAFER-CV-D25501/N26001 3.5" Motherboard Step 5: When the following window appears, press ~~to select “Specify Additional Device”.~~
~~PAGE 167~~
WAFER-CV-D25501/N26001 3.5" Motherboard Step 6: In the following window, select a SATA controller mode used in the system. Then press . The user can now start using the SATA HDD. Step 7: After pressing , the system will get into the recovery tool setup menu. Continue to follow the setup procedure from Step 4 in Section B.2.2 Create 78 Partitions to finish the whole setup process. B.7.
~~PAGE 168~~
~~WAFER-CV-D25501/N26001 3.~~
~~PAGE 169~~
WAFER-CV-D25501/N26001 3.5" Motherboard AC ’97 Audio Codec 97 (AC’97) refers to a codec standard developed by Intel® in 1997. ACPI Advanced Configuration and Power Interface (ACPI) is an OS-directed configuration, power management, and thermal management interface. AHCI Advanced Host Controller Interface (AHCI) is a SATA Host controller register-level interface. ATA The Advanced Technology Attachment (ATA) interface connects storage devices including hard disks and CD-ROM drives to a computer.
~~PAGE 170~~
WAFER-CV-D25501/N26001 3.5" Motherboard DIMM Dual Inline Memory Modules are a type of RAM that offer a 64-bit data bus and have separate electrical contacts on each side of the module. DIO The digital inputs and digital outputs are general control signals that control the on/off circuit of external devices or TTL devices. Data can be read or written to the selected address to enable the DIO functions.
~~PAGE 171~~
WAFER-CV-D25501/N26001 3.5" Motherboard LVDS Low-voltage differential signaling (LVDS) is a dual-wire, high-speed differential electrical signaling system commonly used to connect LCD displays to a computer. POST The Power-on Self Test (POST) is the pre-boot actions the system performs when the system is turned-on. RAM Random Access Memory (RAM) is volatile memory that loses data when power is lost. RAM has very fast data transfer rates compared to other storage like hard drives.
~~PAGE 172~~
~~WAFER-CV-D25501/N26001 3.~~
~~PAGE 173~~
WAFER-CV-D25501/N26001 3.5" Motherboard D.1 Introduction The DIO connector on the WAFER-CV-D25501/N26001 is interfaced to GPIO ports on the Super I/O chipset. The DIO has both 4-bit digital inputs and 4-bit digital outputs. The digital inputs and digital outputs are generally control signals that control the on/off circuit of external devices or TTL devices. Data can be read or written to the selected address to enable the DIO functions.
~~PAGE 174~~
WAFER-CV-D25501/N26001 3.5" Motherboard D.3 Assembly Language Samples D.3.1 Enable the DIO Input Function The BIOS interrupt call INT 15H controls the digital I/O. An assembly program to enable digital I/O input functions is listed below. MOV AX, 6F08H Sets the digital port as input INT 15H Initiates the INT 15H BIOS call D.3.2 Enable the DIO Output Function The BIOS interrupt call INT 15H controls the digital I/O. An assembly program to enable digital I/O output functions is listed below.
~~PAGE 175~~
~~WAFER-CV-D25501/N26001 3.~~
~~PAGE 176~~
WAFER-CV-D25501/N26001 3.5" Motherboard NOTE: The following discussion applies to DOS environment. Contact IEI support or visit the IEI website for specific drivers for other operating systems. The Watchdog Timer is provided to ensure that standalone systems can always recover from catastrophic conditions that cause the CPU to crash. This condition may have occurred by external EMIs or a software bug.
~~PAGE 177~~
~~WAFER-CV-D25501/N26001 3.5" Motherboard NOTE: When exiting a program it is necessary to disable the Watchdog Timer, otherwise the system resets.~~
~~PAGE 178~~
~~WAFER-CV-D25501/N26001 3.~~
~~PAGE 179~~
WAFER-CV-D25501/N26001 3.5" Motherboard F.1 Hazardous Materials Disclosure Table for IPB Products Certified as RoHS Compliant Under 2002/95/EC Without Mercury The details provided in this appendix are to ensure that the product is compliant with the Peoples Republic of China (China) RoHS standards. The table below acknowledges the presences of small quantities of certain materials in the product, and is applicable to China RoHS only.
~~PAGE 180~~
~~WAFER-CV-D25501/N26001 3.~~
~~PAGE 181~~
~~WAFER-CV-D25501/N26001 3.~~