IER 602 Reader User Guide N0F102A N0F102A - Rev.
IER 602 Reader User Guide IER SIEGE - HEADQUARTERS IER S.A.S. 3, rue Salomon de Rothschild 92156 SURESNES CEDEX France Tel. +33 (0)1 41 38 60 00 Fax +33 (0)1 41 38 62 75 IER DANS LE MONDE - IER WORLDWIDE CHINA UNITED ARAB EMIRATES IER Shanghai Kuen Yang Plaza #1101 798 Zhao Jia Bang Road SHANGHAI 200030 P.R.C.
IER 602 Reader User Guide NOTICE WARNING THIS PRODUCT COMES WITH A LITHIUM BATTERY. BATTERY REPLACEMENT MUST IMPERATIVELY BE PERFORMED BY QUALIFIED MAINTENANCE PERSONNEL. MOREOVER, ONLY IER APPROVED MODELS MAY BE USED. DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY REPLACED. REPLACE ONLY WITH THE SAME OR EQUIVALENT TYPE RECOMMENDED BY THE MANUFACTURER. DISPOSE OF USED BATTERIES ACCORDING TO THE MANUFACTURER’S INSTRUCTIONS. The United States Federal Communications Commission (in 47 CFR 15.
IER 602 Reader User Guide NORWAY: This product is also designed for IT power distribution system with phase-to-phase voltage 230V. NORWAY – SWEDEN – FINLAND: Apparaten skall anslutas till jordat uttag när den ansluts till ett nätverk. THIS PRODUCT MUST EXCLUSIVELY BE CONNECTED TO AN ELECTRICAL CIRCUIT PROVIDED WITH A GROUND FAULT CIRCUIT INTERRUPTER (GFCI) AND COMPLYING WITH IEC 364 AND NFC15-100 REGULATIONS.
IER 602 Reader User Guide CONTENTS 1 General ............................................................................................................. 6 1.1. General Description .................................................................................. 6 1.2. User Interface............................................................................................ 7 1.3. Dimensions and Weight ............................................................................ 8 1.4.
IER 602 Reader User Guide 1 GENERAL 1.1. General Description The IER 602 is primarily designed for airport applications to control access to boarding gates and check-in areas or can be used for access control to security check points. The reader can also be integrated into other public space applications, dedicated, for example, to train stations, museums, stadiums, etc.
IER 602 Reader User Guide 1.2. User Interface The IER 602 Reader has a sleek box shape with a slightly slanted top which makes up the user interface. The user interface is divided into the following two zones: - Read zone dedicated to scanning printed barcodes or barcodes displayed on cell phone screens, as well as RF-enabled smart cards. User information zone made up of an LCD graphic display and a LED light bar lighting up either green or red.
IER 602 Reader User Guide 1.3. Dimensions and Weight Depth: 227 mm (8.9 in) Width: 142 mm (5.6 in) Height: 124 mm (4.9 in) Weight: 1.5 kg (3.3 lbs) Angle of the slanted top: 15° in relation to a horizontal plane. 15° Page 8 N0F102A - Rev.
IER 602 Reader User Guide 1.4. Optional Thermal Printer The optional thermal printer allows printing of documents via the IER 602 Reader. This optional device, an add-on, must be connected to a power source and communicates with the reader through a USB or serial connection. Note: Refer to the thermal printer User Guide for information on device installation, operation and recommended maintenance. Page 9 This document is the property of IER and may not be reproduced or N0F102A - Rev.
IER 602 Reader User Guide 2 READER CONNECTIONS WARNING This product must exclusively be connected to an electrical circuit provided with a ground fault circuit interrupter (GFCI) and complying with IEC 364 and NFC15-100 regulations. Make sure the reader is switched off (power switch set to the 0-position) and that the power cord is disconnected. It is vital to proceed in the order described. To comply with class B FCC regulations it is necessary to use a data cable provided with a braided shield.
IER 602 Reader User Guide 2.1. Connecting the Reader CAUTION The IER 600 Reader switches automatically to the available AC power within the authorized voltage ranges, i.e. 100-120Vac-60 Hz or 200-240Vac-50 Hz.
IER 602 Reader User Guide 3 OPERATION 3.1. Operating Conditions and Power Requirements 3.1.1. Environment Operating temperature ............................. +5°C to 40°C (+41°F to +104°F) Storage temperature ..................................-20°C to 60°C (-4°F to +140°F) Relative humidity ..................................20% to 80%, without condensation Operating environment .................................................. fully enclosed area .....................................
IER 602 Reader User Guide 3.2. Powering up the Reader Switch the AC power switch to the I-position. On power up, allow for an approximately 40-sec. initialization period before the IER 602 is operational. Page 13 This document is the property of IER and may not be reproduced or N0F102A - Rev.
IER 602 Reader User Guide 3.3. Barcode Scanning Recommendations IMPORTANT When scanning barcodes, it is important to keep the following recommendations in mind: Present one single document at a time. Place the barcode face down on and in the center of the scanner window. Place the document horizontally on the scanner window without moving it.
IER 602 Reader User Guide 3.4. Reading a Barcoded or RF-Enabled Document Hold the barcoded or RF-enabled document to be read face down against the scan/read window (keeping in mind the recommendations listed page 14).
IER 602 Reader User Guide 3.5. Powering down the Reader Set the AC Power switch to the 0-position. Page 16 N0F102A - Rev.
IER 602 Reader User Guide 4 MAINTENANCE 4.1. Periodic Maintenance To ensure optimum bar code reading, it is important to keep the scanner window clean. The decision on the periodicity of window cleaning is up to the personnel in charge of the reader. IMPORTANT: To clean the glass of the scanner window, exclusively use a soft, nonabrasive cloth containing cotton. Only use window cleaning products. Be careful not to splash or spray any water or cleaning product directly on the scanner window.