User Manual
Thank you for purchasing this NEO series Stream. The NEO Stream is a Ultra-Res network audio streamer.
/ 1 1. OLED display 2. Multi-function knob 3. Network Status LED 2 2 P.4 P.4-5 P.6 3 4 5 SS 6 4. Input selector/Settings 5. Power switch and indicator 6. USB-C input/output P.6 P.6 P.
7 11 9 15 13 17 19 Stand Alone 8 7. 8. 9. 10. 11. DC power supply connection M12 Ethernet input RJ45 Ethernet input Factory Reset Optical input 10 12 P.7 P.7 P.7 P.7 P.7 12. 13. 14. 15. 16. 14 16 USB-C System upgrade port USB Type A x 2 port HDMI output Balanced 4.4mm analogue output Single-Ended RCA output 18 P.7 P.8 P.8 P.8 P.8 20 17. 18. 19. 20. S-PDIF Optical output P.8 S-PDIF Coaxial output P.8 AES/EBU (XLR) signal outputs P.9 Wi-Fi antenna P.9 Quick Start Guide P.
1. OLED display The OLED display showing current player, sample rate, web address. Tip: OLED screen is on left side when Stream is lying flat. 2. Multi-function knob Cycles Controls: - Screen Brightness (short press) - SYSTEM STATUS - Advanced setting - Audio output port selection - System (Mode) selector - Hotspot selection short press once to enter the selection, turn the knob to switch options, short press again to confirm the selection.
II) SYSTEM STATUS Showing Ethernet IP, Host URL, WiFi iP, Hotspot IP, System Version. III) Advanced setting ‘ ’ Simple Display Ethernet IP and Hotspot URL Advanced Display Ethernet IP, Hotspot URL, WiFi iP, Hotspot IP, System Version. IV) Audio output port selection ‘ ’ Choose between Analog or Digital and USB DAC audio output. V) System (Mode) selector ‘ ’ The following 5 play modes can be selected: - All In One.
3. Network Status LED LED lnternet White lnternet Cyan Local network Green No lnternet Yellow No connection Red Speed Fast Slow Fast Slow - 4. Input selector/Settings Choose between Analog or Digital and USB DAC audio output. 5. Power switch and indicator Short press ≥ 1s to switch on, long press ≥ 2s to switch off. 6.
7. DC power supply connection DC 9V/3A-15V/2A DC power input. Please connect ZEN Stream to the enclosed power supply. 8. M12 Ethernet input Connect a network cable with M12 connector. 9. RJ45 Ethernet input Connect a network cable with RJ45 connector.Optical network input 10. Factory Reset Long press ≥ 3 seconds, wait 3 minutes and the screen will appear with the ifi interface. DO NOT POWER OFF! Warning: Loss of power during this period may damage your device and leave it unusable. 11.
13. USB Type A x 2 Compatible with USB 2.0 and USB 3.0. a) Output - Connect to DAC b) Input - Connect to HDD, USB DISK etc These two USB ports have ANC technology built- in. 14. HDMI output HDMI signal output connect to DAC 15. Balanced 4.4mm output Connection of 4.4mm to XLR or similarly balanced interconnects. 16. Single-Ended RCA output Connect analogue RCA interconnects to an amplifier. 17. S-PDIF Optical output* This is a S-PDIF Optical signal output. 18.
19. AES/EBU (XLR) signal output AES/EBU (XLR) Balanced signal output to an amplifier. 20. Wi-Fi antenna Please attach the enclosed antenna for maximum reception quality.
Quick Start Guide 10
11
