iA91/iA92 IB_US version Size: 178 x 178 mm (16 pages) Printing color: Black Mat’l: 90gsm book paper Apr. 14, 11. P1 Model iA91/iA92 The App-enhanced Home System For Your iPhone® or iPod® works with iHome + Sleep alarm clock app iHome + Radio internet radio app download QR code reader app and scan Note: iHome+Sleep and iHome+Radio apps are not covered in detail in this booklet.
P2 Table of Contents Quick Start ........................................................................................................................................................................1 Controls and Indicators / Unit Display ..........................................................................................................................2 Setting Up the Unit ..............................................................................................................................
P3 quick start 1: power 2: antennas 3: inserts Tab RESET R ESET TEST T EST Slot Attach AC adaptor cable to DC jack on back of the unit and plug the other end into a wall socket. Uncoil AM antenna cable from antenna frame and plug cable into socket on back of unit. Hold base of AM antenna in one hand and bend the outer frame around towards the base and snap tabs into open slot on base. Move antenna 12” away. Extend FM antenna. NOTE: Inserts provide the best stability for your iPhone or iPod.
P4 Controls and Indicators Top Panel Dock Play/Pause Button Alarm 2 Button Nap Button Alarm 1 Button Bedtime Button Lower/raise volume Button Set +/- Button, skip/search FWD/REV nap bedtime mode eq presets alm. reset wakeup Alarm Reset / Power Button Wakeup Button snooze/dimmer Mode Button EQ Button Presets Button Snooze/Dimmer Button Rear Panel Clock Adjust /Time Sync Button AC Adaptor Jack DST switch AM Antenna 7.5V 2.
P5 Setting Up the Unit Connect Unit to Power Source Plug the AC adaptor cable into the AC Adaptor Jack and the other end into a standard 120V AC wall socket. Adaptor must be plugged in to operate unit. The unit does not operate on batteries (a battery back up system maintains clock settings during power failures). Updating firmware on the Unit For best performance, make sure to update the unit’s firmware. To do so, download the free iHome+Sleep app from the App Store.
P6 Using the unit Using the Alarms This unit has a dual alarm system so you can set two separate alarms to different alarm times, wake-to sources and frequencies (daily, weekdays or weekend). Tip: Download the free iHome+Sleep app for advanced alarm, snooze and sleep functions. Setting the Alarms Note: Alarm 1 and Alarm 2 are set the same way; Alarm Button below means the button ( or ) for whichever alarm you are setting. 1.
P7 Using the unit Snooze Operation 1. Default snooze time is 9 minutes. To program a custom snooze time, press and hold the Snooze Button during normal operation (when alarm is not sounding) until the snooze minutes display appears. Press and release the + or - Button to set the snooze timer from 1 to 29 minutes. Press and release the Snooze/Dimmer Button to exit snooze setting mode. 2. Press and release the Snooze/Dimmer Button after an alarm sounds.
P8 Using the unit 3. You can set up to 12 presets (6 AM, 6 FM).To memorize a station as a preset: A. Press and release the Mode Button to select the desired AM or FM band. B. Press and release the Presets Button as needed to step through the 6 presets (P1 - P6) to the number you wish to assign, and then hold the Presets Button until the selected preset number begins flashing in the display. C. Press and release the + or - Button to tune the radio to a desired station.
P9 Using the Unit Nap Operation Nap mode lets you set an alarm separate from the Alarm 1 and Alarm 2 settings. The nap wake to source by default is the buzzer alarm, but if an iPhone/iPod is docked (no other source is playing), that will act as the alarm source. If you are listening to the radio or aux-in source, it will be muted and the buzzer will sound at the selected wake time. 1.
P10 A Consumer Guide to Product Safety IMPORTANT SAFETY INSTRUCTIONS When used in the directed manner, this unit has been designed and manufactured to ensure your personal safety. However, improper use can result in potential electrical shock or fire hazards. Please read all safety and operating instructions carefully before installation and use, and keep these instructions handy for future reference. Take special note of all warnings listed in these instructions and on the unit. 1. 2. 3. 4. 5. 6. 7. 8.
P11 Troubleshooting Symptom Unit does not turn on Unit doesn’t respond Possible Problem Solution AC adaptor isn't plugged into a working wall socket or not plugged into the power supply jack on back of the unit Unit requires a reset Plug the AC adaptor into a working wall socket and plug the connector into the supply jack on the unit If unit is plugged in and doesn't respond, try resetting the unit by following these steps: a) remove iPhone/iPod from dock b) unplug unit from power source c) remove back
P12 Troubleshooting Symptom Sound is distorted Possible Problem Solution Volume level is set too high Decrease the volume Sound source is distorted If the iPhone/iPod original sound source is old or of poor quality, distortion and noise are easily noticed with high-power speakers. Try a different audio file from a trusted source such as iTunes. If you are using an external sound source try reducing the output volume on the device itself. Also try turning bass boost OFF. EQ settings are too high.
P13 Limited 1 Year Warranty Information iHome Products, a division of SDI Technologies Inc. (hereafter referred to as SDI Technologies), warrants this product to be free from defects in workmanship and materials, under normal use and conditions, for a period of 1 Year from the date of original purchase. Should this product fail to function in a satisfactory manner, it is best to first return it to the store where it was originally purchased.