Model iH64 Portable Computer Speakers for your iPod Questions? Visit www.ihomeaudio.
Table of Contents Quick Start ......................................................................................................................................................................... 1 Controls and Indicators....................................................................................................................................................... 2 Using iH64...........................................................................................................................
FCC Information This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Quick Start: Connections 1:connections 2:power Important: Turn off iH64 before connecting or disconncting speakers! 1. Power off iH64. 2. Connect the right speaker to the speaker jack on the back of main unit. 3. Connect the left speaker to the speaker jack on the back of right speaker. Attach the AC adaptor cable to the jack on the back of the main unit and plug the other end into a working wall socket. 3:inserts Select the dock insert for your iPod model from the table below and place insert in dock.
Controls and Indicators Top Panel iPod sync Button iPod sync iPod sync LED iPod Dock Volume - Button Power Button Volume + Button Power LED Rear Panel USB Port Line-in Jack Speaker Jack iPod sync line-in AC Adaptor Jack DC 7.
Using iH64 Install iPod Insert Your iH64 comes with inserts to ensure your iPod fits properly in the dock. To place an insert: 1. Select the insert for your iPod (see table on page 1). 2. Gently press the iPod insert into the dock. 3. Carefully place your iPod into the dock. The iPod must not be in a case or “skin”. Connect Speakers Important: You must turn off the iH64 before connecting or disconnecting speakers! 1. Power off iH64. Install iPod Insert 2.
Listening to non-docking iPod or other audio devices If you are using an iPod without a docking port or other MP3 player or portable audio device, you can play it through the iH64 via the Line-in Jack. 1. Plug one end of an audio cable (available at www.ihomeaudio.com) into the headphone or line-out jack on your device and the other end of the audio cable into the iH64 Line-in Jack. 2. Press the Button to turn the iH64 on. 3. Press the or Buttons to adjust the system volume.
Using the Optional Remote Control Power Button turns unit ON and OFF Volume Buttons raise and lower volume on the unit. Pressing FWD/REV while iPod is inserted will FWD/REV to next/previous track Pressing and holding FWD/REV while iPod is docked will scan forward/reverse within currently playing track. Pressing Play/Pause from power off mode will play iPod. Pressing Play/Pause while iPod is docked and playing will pause iPod. Press again to resume play.
A Consumer Guide to Product Safety When used in the directed manner, this unit has been designed and manufactured to ensure your personal safety. However, improper use can result in potential electrical shock or fire hazards. Please read all safety and operating instructions carefully before installation and use, and keep these instructions handy for future reference. Take special note of all warnings listed in these instructions and on the unit. 1.
Trouble Shooting Symptom Unit doesn’t respond (no power) Possible Problem Solution AC adaptor isn’t plugged to a wall outlet or the connector is not plugged into the power supply jack on the back of the unit Wall outlet is not functioning Plug the AC adaptor into a wall outlet and plug the connector into the supply jack on the unit iPod does not dock properly Using no or wrong iPod insert Make sure the dock insert is the proper one for your iPod Dock or connector is obstructed iPod does not respond
Solucionando Problemas Síntoma La unidad no responde (no enciende) El iPod no encastra correctamente El iPod no se comunica con la unidad El iPod no carga El sonido sale distorsionado El control remoto no funciona Causa Posible Solución El adaptador de AC no ha sido conectado a la corriente eléctrica o el cable no ha sido conectado a la parte posterior de la unidad. El tomacorrientes no funciona. Conecte el adaptador AC al tomacorrientes y el cable a la ficha de entrada de la unidad.
Limited 90-Day Warranty Information iHome Products, a division of SDI Technologies Inc. (hereafter referred to as SDI Technologies), warrants this product to be free from defects in workmanship and materials, under normal use and conditions, for a period of 90 days from the date of original purchase. Should this product fail to function in a satisfactory manner, it is best to first return it to the store where it was originally purchased.