iP43 IB in USA English version Print color : Black text on white paper Size of manual: 178mmW x 178mmH Sept 2,2010 Model iP43 FM alarm clock radio with pillow shaker Questions? Visit www.ihomeaudio.
Table of Contents Quick Start .........................................................................................................................................................................1 Controls and Indicators ................................................................................................................................................ 2-3 iP43 Display .............................................................................................................................
iP43 Quick start 2: inserts 1: power 3: time sync RESET RESET TEST TEST Attach AC adaptor cable to DC jack on back of the iP43 and plug the other end into a working outlet. Select the dock insert for your iPhone or iPod® model from the table below and place insert in dock. • Dock your iPhone • Press the Time set/sync button on back of the unit. • “SYNC” will flash on the display, indicating sync attempt • “SYNC OK” will appear and you will hear 2 beeps when sync is complete.
Controls and Indicators Top Panel Dock Preset Buttons 1-6 EQ Button Volume Wheel Set Wheel Alarm Reset / Power Button Play/Pause Button Radio Button Alarm 2 Button Sleep Button Alarm 1 Button Snooze/Dimmer Button Rear Panel Time Set/ Sync Button DST switch DC 7.
Controls and Indicators Pillow Shaker On/OFF Switch Line-in Plug Snooze Button iP43 Display NOTE: AM/PM indicators will not appear when clock is set to 24 hour display mode Time Display PM Indicator AM Indicator Wake to Icon Sleep Mode Icon Battery Low Indicator wake to Alarm Indicators FM Radio Indicator Alarm Time Display 3
Installing/Replacing the iP43 Backup Batteries The iP43 uses “AA” LR06 batteries (pre-installed) for backup battery system to provide continuous alarm operation and clock settings in the event of a power failure. If the Battery Low Icon located on the right of the display is flashing, it is time to replace the backup batteries. Please make sure the AC adaptor is connected, otherwise all settings may be lost during battery replacement. 1.
Setting Up the iP43 Connect iP43 to Power Source Plug the AC adaptor cable into the AC Adaptor Jack and the other end into a standard 120V AC wall socket. Adaptor must be plugged in to operate unit. The iP43 does not operate on batteries (a battery back up system maintains clock settings during power failures). This unit is a preset clock: the clock is preset at the factory. It’s simple to match the Time Zone setting to your location (US only). 1.
Using the iP43 Alarms Using the Alarms iP43 has a dual alarm system so you can set two separate alarms to different alarm times, wake-to sources and frequencies (daily, weekdays or weekend). Using the Pillow Shaker The iP43 comes with a pillow shaker that plugs into the pillow shaker jack on the back of the unit. You can wake to any alarm mode with or without the shaker.
Using the iP43 Alarms Resetting the Alarm to Come on the Next Day When an alarm is sounding, press the Button to stop the alarm and reset it to come on the next set day. For example, if an alarm is set for 5 days and you press the alarm reset on Friday, the alarm will come on again on Monday, not Saturday. Snooze Operation 1. Press and hold the Snooze/Dimmer Button for a few seconds until the snooze time flashes. Turn the Set Wheel to set the snooze timer from 1 to 29 minutes. 2.
To memorize a station as a preset 1. In Radio mode, turn the Set Wheel to select a station. 2. Press and hold the desired Preset Button until the odd number preset (P1, P3, P5) flashes on the display; press again to assign the station to the related even number preset (P2, P4, P6). Allow to time-out. You will hear a beep confirming the preset has been assigned. To change presets, repeat steps 1 and 2. To access a preset station 1.
A Consumer Guide to Product Safety When used in the directed manner, this unit has been designed and manufactured to ensure your personal safety. However, improper use can result in potential electrical shock or fire hazards. Please read all safety and operating instructions carefully before installation and use, and keep these instructions handy for future reference. Take special note of all warnings listed in these instructions and on the unit. 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14.
Troubleshooting Symptom Possible Problem Solution iP43 does not turn on AC adaptor isn't plugged into a working wall socket or not plugged into the power supply jack on back of the unit iP43 doesn’t respond iP43 requires a reset Plug the AC adaptor into a working wall socket and plug the connector into the supply jack on the unit If unit is plugged in and doesn't respond, try resetting the unit by following these steps: a) remove iPhone/iPod from dock b) unplug unit from power source c) remove back up b
Troubleshooting Symptom Sound is distorted Possible Problem Solution Volume level is set too high Decrease the volume Sound source is distorted If the iPhone/iPod original sound source (MP3) is old or of poor quality, distortion and noise are easily noticed with high-power speakers. Try updating the sound file from a trusted source such as iTunes. If you are using an external sound source like older generation of iPod or iPod Shuffle, try reducing the output volume on the device itself.
Limited 1 Year Warranty Information iHome Products, a division of SDI Technologies Inc. (hereafter referred to as SDI Technologies), warrants this product to be free from defects in workmanship and materials, under normal use and conditions, for a period of 1 Year from the date of original purchase. Should this product fail to function in a satisfactory manner, it is best to first return it to the store where it was originally purchased.
