Model iP99 The Home System For Your iPhone® or iPod®
Table of Contents Caution Information ........................................................................................................................................................ 1 Quick Start ....................................................................................................................................................................... 2 Controls and Indicators / iP99 display ..................................................................................................
CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
iP99 quick start 3:inserts 1:power 2:antenna Attach AC adaptor cable to jack on back of the iP99 and plug the other end into a working wall socket. Snap AM antenna into provided stand, then plug antenna cable into socket on back of iP99. Move antenna 12” away. NOTE: If you do not have an insert for your iPhone/iPod, please visit an Apple store, www.ihomeaudio.com, or call iHome toll free at 800-288-2792 to purchase one.
Controls and Indicators Top Panel Dock Radio Button Preset Buttons Set Wheel Volume Wheel Alarm Reset / Power Button SPUL PU Play/Pause Button LX Alarm 2 Button EQ Button Sleep Button Alarm 1 Button Snooze/Dimmer Button Rear Panel Time Zone Button Clock Adjust Button AC Adaptor Jack DST switch +* = T( JSVJR HKQ [PTL aVUL +:; HT HU[LUUH Line-in Jack SPUL PU AM Loop Antenna socket FM Antenna iP99 display Time Display Sleep Indicator PM Indic
Using the iP99 Connect iP99 to Power Source Plug the AC adaptor cable into the AC Adaptor Jack and the other end into a standard 120 VAC wall socket. Adaptor must be plugged in to operate. The iP99 does not operate on batteries. Setting the Clock Press and hold the Time Zone Button until the display flashes. Turn the Set Wheel to select your time zone. Press the Time Zone Button again. The clock will display the current time in your time zone.
Using the iP99 Radio Setting up Antennas a) Snap AM loop antenna into provided stand, then plug AM antenna cable into AM Loop Antenna socket on back of unit. Move antenna away from unit and AC adaptor for best reception. b) Extend FM Antenna (on back of unit) fully for best reception. Do not strip, alter or attach to other antennas. Tuning and Playing the Radio a) Press the Radio Button to select radio play mode. Press as needed to select FM or AM radio band.
Using The Remote Control The Remote Control controls basic functions on the iP99 and certain iPhone/iPod functions when the iPhone/iPod is docked in the iP99. For best results, use the remote control within 12 feet of the unit. TLU\ LU[LY T\[L YHKPV LX ZUVVaL SPUL PU ZSLLW WYLZL[Z Power On/Off Alarm Reset Button: Turns iP99 ON or OFF or resets alarm when alarm is sounding Fwd/Rev Button: Skip to previous or next track, or HOLD to scan current playing track.
Troubleshooting Symptom Possible Problem Solution iP99 does not turn on AC adaptor isn't plugged into a working wall socket or not plugged into the power supply jack on back of the unit Plug the AC adaptor into a working wall socket and plug the connector into the supply jack on the unit iP99 doesn’t respond iP99 requires a reset If unit is plugged in and doesn't respond, try resetting the unit by following these steps: a) remove iPhone/iPod from dock b) unplug unit from power source c) remove back
Troubleshooting Symptom Possible Problem Solution No AM band radio sound but others OK AM loop antenna is not connected to the unit Plug the AM loop antenna connector to the jack on the back of the unit AM band radio is very noisy AM loop antenna isn’t located properly Move the AM loop antenna away from the main unit and AC adaptor and rotate it for best reception Unit makes odd beeping noise in radio mode GSM noise: iPhone is sending signals to cell towers Undock your iPhone or put iPhone in Air
Solucionando problemas Síntoma Causa Solución La unidad no enciende El adaptador de corriente AC no está conectado a un tomacorriente que funcione o no está conectado en la parte posterior de la unidad Conecte el adaptador de corriente a un tomacorriente que funcione y a la parte posterior de la unidad La unidad no responde La unidad debe ser reprogramada Si la unidad está conectada y no responde, pruebe reprogramarla siguiendo estos pasos: a) Quite el iPhone/iPod de la base b) Desconecte la unidad
Solucionando problemas Síntoma Causa Solución La banda de AM no suena pero las demás sí La antena no está ubicada correctamente Aleje la antena de la unidad y gírela para mejorar la recepción El sonido sale distorsionado El volumen se encuentra muy alto Baje el volumen El sonido sale distorsionado de la unidad Si el sonido original de su iPhone/iPod era de pobre calidad, las distorsiones y ruidos se harán más notables con los parlantes de alta potencia.
A Consumer Guide to Product Safety When used in the directed manner, this unit has been designed and manufactured to ensure your personal safety. However, improper use can result in potential electrical shock or fire hazards. Please read all safety and operating instructions carefully before installation and use, and keep these instructions handy for future reference. Take special note of all warnings listed in these instructions and on the unit. 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16.
Limited 90-Day Warranty Information iHome Products, a division of SDI Technologies Inc. (hereafter referred to as SDI Technologies), warrants this product to be free from defects in workmanship and materials, under normal use and conditions, for a period of 90 days from the date of original purchase. Should this product fail to function in a satisfactory manner, it is best to first return it to the store where it was originally purchased.